Sharp FPF60UW Operation Manual

Download

FP-F60U-W

Device of this mark is a trademark of Sharp Corporation. “Plasmacluster” and “Device of a cluster of grapes” are

registered trademarks of Sharp Corporation in Japan, USA and elsewhere.

AIR PURIFIER OPERATION MANUAL

ENGLISH

Purificateur d’air à fonction MANUEL D’UTILISATION

FRANÇAIS

PURIFICADOR DE AIRE MANUAL DE OPERACIÓN

ESPAÑOL

This product earned the ENERGY STAR by meeting strict energy efficiency guidelines set by the US EPA. US EPA does not endorse any manufacturer claims of healthier indoor air from the use of this product.

The energy efficiency of this ENERGY STAR qualified model is measured based on a ratio between the model’ s CADR for Dust and the electrical energy it consumes, or CADR/Watt.

Ce produit a le droit de porter la marque ENERGY STAR après avoir répondu à des critères stricts en ce qui concerne l’efﬁcacité énergétique, tels qu’établis par l’agence EPA aux É-U. L’agence EPA aux É-U n’appuie aucunement les témoignages publicitaires du fabricant indiquant que ce produit rend l’air intérieur des locaux plus sain.

L’efﬁcacité énergétique de ce modèle, qui bénéﬁcie de la reconnaissanc rapport entre le DAP (débit d’air puriﬁé) du modèle et l’ énergie électrique qu’il consomme, soit le rapport DAP/ Watt.

e ENERGY STAR, est mesurée par le

Please read before operating your new Air Puriﬁer

The air puriﬁer draws in room air from the air intake, passes the air through a PreFilter, a Deodorizing ﬁlter and a True HEPA ﬁlter inside of the unit, then dis-charges the air through the air outlet. The True HEPA ﬁlter can remove 99.97% of dust particles as small as 0.3 microns that pass through the ﬁlter and also helps absorb odors. The Deodorizing ﬁlter gradually absorbs odors as they pass through ﬁlter.the

Some odors absorbed by the ﬁlters may break down over time, resulting in additional

odor. Depending on the usage environment, especially when the product is used in ex-

treme environments (signiﬁcantly more severe than normal household use), this odor may become strong in a shorter period than expected. If the odor persists, the ﬁlters

should be replaced.

NOTE

• The air purifier is designed to remove air-suspended dust and odor, but not harmful gases (for example,

carbon monoxide contained in cigarette smoke). If the source of the odor still exists, the air puriﬁer may

not completely remove the odor.

HEPA Filter

Active Carbon Deodorizing Filter

Back Panel (Pre-filter)

ENGLISH

FEATURES

Unique Combination of Air Treatment Technologies

Triple Filtration System + Plasmacluster Ion.

TRAPS DUST*

W ashable pre-filter traps dust and other large airborne particles.

DECREASES ODORS

Deodorizing ﬁlter absorbs many common

household odors.

REDUCES POLLEN & MOLD*

True HEPA ﬁlter traps 99.97% of particles as small as 0.3 microns.

FRESHENS

Plasmacluster refreshes the air similar to the way nature cleans the environment by emitting a balance of positive and negative ions.

*When air is drawn through the filter system.

Declaration of Conformity SHARP AIR PURIFIER FP-F60U

This device complies with Part 15 of FCC rules.

Responsible Party:

SHARP ELECTRONICS CORPORATION

100 Paragon Drive, Suite #100, Montvale, NJ 07645, U.S.A

CONTENTS

FOR CUSTOMER ASSISTANCE(U.S) CONSUMER LIMITED WARRANTY(U.S) FOR CUSTOMER ASSISTANCE(CANADA) LIMITED WARRANTY(CANADA) IMPORTANT SAFETY INSTRUCTIONS

• WARNING ..................................................

• CAUTIONS CONCERNING OPERATION .

• INSTALLATION GUIDELINES ....................

• FILTER GUIDELINES ................................

PART NAMES

• FRONT VEW ..............................................

• BACK VEW ................................................

• CONTROL PANEL .....................................

PREPARATION FOR USE ..........................

• FILTER INSTALLATION ...........................

OPERATION

• CLEAN AIR MODE ...................................

• QUICK CLEAN MODE .............................

• FAN SPEED Button .................................

• Plasmacluster ON/OFF Button ................

• CHILD LOCK Button ................................

• POWER ON/OFF Button .........................

•

LIGHT CONTROL BRIGHT/DIM/OFF Button

• OFF TIMER Button ..................................

ADJUSTMENT OF SENSOR DETECTION SENSITIVITY

•

CARE AND MAINTENANCE

• REAR PANEL (PRE-FILTER) ........................

• MAIN UNIT ..............................................

• HEPA FILTER, ACTIVE CARBON

DEODORIZING FILTER ..........................

•

FILTER REPLACEMENT GUIDELINES

TROUBLESHOOTING SPECIFICATIONS

.............................................

.................

............................

....................................

......

.....

....

...........

...

.....

E-2 E-3 E-4 E-5 E-6

E-6 E-7 E-7 E-7

E-8 E-8 E-8 E-9

E-10 E-10

E-11 E-11 E-11 E-12 E-12 E-12 E-12 E-13 E-13 E-13

E-14 E-14 E-15

E-15 E-16

E-17 E-19

ENGLISH

Declaration of Conformity SHARP AIR PURIFIER FP-F60U

Thi s ISM dev i ce c omplies with Canadian ICES-3(B)

Responsible Party:

SHARP ELECTRONICS OF CANADA LTD. 335 Britannia Road East Mississauga, Ontario L4Z 1W9 Canada TEL: (905) 568-7140

Thank you for purchasing this SHARP Air Puriﬁer. Please read this manual carefully before using the air puriﬁer.After reading, keep the manual in a conven-ient location for future reference.

E-1

FOR CUSTOMER ASSISTANCE

To aid in answering questions if you call for service or for reporting loss or theft, please use the space below to record the model and serial number located on the back of the unit.

MODEL NUMBER

SERIAL NUMBER

DATE OF PURCHASE

Dealer Name

Address

City

State

Zip

Telephone

(the United States)

TO PHONE: Dial 1-800-BE-SHARP (237-4277) for:

SERVICE (for your nearest Sharp Authorized Servicer) PARTS (for your Authorized Parts Distributor) ACCESSORIES ADDITIONAL CUSTOMER INFORMATION

TO WRITE: For service problems, warranty information, missing items and other assistance:

Sharp Electronics Corporation Customer Assistance Center

Sharp Plaza Blvd.

Memphis, TN 38193

TO ACCESS OUR WEB SITE: www.sharpusa.com

Please provide the following information when you write or call: model number, serial

number, date of purchase, your complete mailing address (including zip code), your daytime telephone number (including area code) and description of the problem.

E-2

CONSUMER LIMITED WARRANTY

CONSUMER LIMITED WARRANTY FOR U.S. USERS

SHARP ELECTRONICS CORPORATION warrants to the ﬁrst consumer purchaser that this Sharp brand product ( the “Product”), when shipped in its original container, will be free from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent at no charge to the purchaser for parts or labor for the period(s) set forth below.

This warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set forth below nor to any Product the exterior of which has been damaged or defaced, which has been subjected to improper

voltage or other misuse, abnormal service or handling, or which has been altered or modiﬁed in design or construction.

In order to enforce the rights under this limited warranty, the purchaser should follow the steps set forth below and provide proof of purchase to the servicer.

The limited warranty described herein is in addition to whatever implied warranties may be granted to purchasers by law. ALL IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE ARE LIMITED TO THE PERIOD(S) FROM THE DATE OF PURCHASE SET FORTH BELOW. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.

Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those described herein, or to extend the duration of any warranties beyond the time period described herein on behalf of Sharp.

The warranties described herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and exclusive remedy available to the purchaser. Correction of defects, in the manner and for the period of time described

herein, shall constitute complete fulﬁllment of all liabilities and responsibilities of Sharp to the purchaser with respect to

the Product, and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise. In no event shall Sharp be liable, or in any way responsible, for any damages or defects in the Product which were caused by repairs or attempted repairs performed by anyone other than an authorized servicer. Nor shall Sharp be liable or in any way responsible for any incidental or consequential economic or property damage. Some states do not allow the exclusion of incidental or consequential damages, so the above exclusion may not apply to you.

THIS WARRANTY GIVES YOU SPECIFlC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARYFROM STATE TO STATE.

Your Product Model Number & Description:

Warranty Period for this Product:

Additional Item(s) Excluded From Warranty Coverage:

Where to Obtain Service:

FP-F60U-W Air Puriﬁer. Be sure to have this information available when you need service for your Product.

One (1) year parts and labor from date of purchase.

Appearance items of the Product, ﬁlters, accessories, or any printed

materials. Product which has been used for rental and/or commercial purposes.

From a Sharp Authorized Servicer located in the United States. To

ﬁnd the location of the nearest Sharp Authorized Servicer, call Sharp

Toll Free at 1-800-BE-SHARP.

ENGLISH

What to Do to Obtain Service:

TO OBTAIN SUPPLY, ACCESSORY OR PRODUCT INFORMATION, CALL 1-800-BE-SHARP, OR VISIT OUR WEBSITE AT www.sharpusa.com

Ship prepaid or carry in your Product to a Sharp Authorized Servicer. Be sure to have Proof of Purchase available. If you ship the Product, be sure it is insured and packaged securely.

SHARP ELECTRONICS CORPORATION

100 Paragon Drive, Suite #100, Montvale, NJ 07645, U.S.A.

E-3

FOR CUSTOMER ASSISTANCE

To aid in answering questions if you call for service or for reporting loss or theft, please use the space below to record the model and serial number located on the back side of the unit.

MODEL NUMBER

SERIAL NUMBER

DATE OF PURCHASE

Dealer Name

Address

City

Province

Postal Code

Telephone

(Canada)

TO PHONE: Dial 1-905-568-7140 for:

SERVICE (for your nearest Sharp Authorized Servicer) PARTS (for yourAuthorized Parts Distributor) ACCESSORIES ADDITIONAL CUSTOMER INFORMATION

TO WRITE: For service problems, warranty information, missing items and

other assistance:

Sharp Electronics of Canada Ltd. Customer Care 335 Britannia Road East Mississauga, Ontario L4Z 1W9

TO ACCESS OUR WEB SITE: www.sharp.ca

Please provide the following information when you write or call: model number, serial number,

date of purchase, your complete mailing address (including Postal Code), your daytime telephone number (including area code) and description of the problem.

E-4

LIMITEDWARRANTY

Consumer Electronics Products

Congratulationsonyourpurchase!

Sharp Electronics of Canada Ltd. (“Sharp”) warrants to the first purchaser for this Sharp brand product (“Product”), when shipped in its original

container and sold or distributed in Canada by Sharp or by an authorized Sharp dealer, and Product was not sold “as is” or “sales final” that the Product will during the applicable warranty period, be free from defects in material and workmanship, and will within the applicable warranty period, either repair the defective Product or provide the first purchaser a replacement of the defective Product.

Conditions: This limited warranty shall not apply to: (a)

Any defects caused or repairs required as a result of abusive operation, negligence, accident, improper installation or inappropriate use as outlined in the owner’s manual or other applicable Product documentation.

(b)

Any defects caused or repairs required as a result of any Product that has been tampered with, modified, adjusted or repaired by any person other than Sharp, a Sharp authorized service centre or a Sharp authorized servicing dealer.

(c)

Any defects caused or repairs required as a result of the use of the Product with items not specified or approved by Sharp, including but not limited to chemical cleaning agents.

(d)

Any replacement of accessories required through normal use of the Product, including but not limited to, earphones, remote controls, AC adapters, batteries, temperature probe, trays, filters, belts, ribbons, cables and paper.

(e)

Any cosmetic damage to the Product surface or exterior that has been defaced or caused by normal wear and tear.

(f)

Any defects caused or repairs required as a result of damage caused by any external or environmental conditions, including but not limited to, transmission line/power line voltage or liquid spillage or acts of God.

(g)

If the serial number or model number affixed to Product has been removed, defaced, changed, altered or tampered with.

(h)

This limited warranty will not apply if the Product has been used or is being used in a commercial setting or application; this warranty is meant solely for the non-commercial, household use of the Product by consumers in their home or residence.

(i)

Any installation, delivery, setup and/or programming charges

(j)

The removal and reinstallation of Over-The-Range Microwave or Microwave Drawer if it is installed in an inaccessible location or requiring removal of cupboards, handles or other cosmetic parts, or is not installed in accordance with installation instructions included with Product.

How to get service: Warranty service may be obtained upon delivery of the Product, together with proof of purchase (including date of purchase) and

a copy of this limited warranty statement, to an authorized Sharp service centre or an authorized Sharp servicing dealer. In home warranty service will be carried out to locations accessible by on-road service vehicle and within 50 km of an authorized Sharp service centre on any Sharp Television with

the repair at the servicer's facility. No other person (including any Sharp dealer or service centre) is authorized to extend, enlarge or transfer this

warranty on behalf of Sharp. The purchaser will be responsible for any and all removal, reinstallation, transportation and insurance costs incurred with exception for Over-The-Range Microwave Oven or Microwave Drawer Oven whereby Sharp will be responsible for the removal and reinstallation.

The express warranties in this limited warranty are, except for consumer purchasers domiciled in Quebec, in lieu of and, except to the extent prohibited by applicable law, Sharp disclaims all other warranties and conditions, express or implied, whether arising by law, statute, by course of dealing or usage of trade, including, without limitation, implied warranties or conditions of merchantability and/or quality, fitness for a particular use or purpose, and/or noninfringement. Limitations (not applicable to consumer purchasers domiciled in Quebec to the extent prohibited under Quebec law): (a) Sharp shall not be liable for any incidental, special, consequential, economic, exemplary or indirect damages of any kind or nature (including lost profits or damages for

loss of time or loss of use or loss of data) arising from or in any connection with the use or performance of a Product or a failure of a Product, even if Sharp is aware of or has been advised of the possibility of such damages; (b) the remedies described in this limited warranty constitute complete

fulfillment of all obligations and responsibilities of Sharp to the purchaser with respect to the Product and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise. Some provinces may not allow the exclusion or limitation of certain damages, or limits on the duration or voiding of implied warranties or conditions; in such provinces, the exclusions and limits herein may not apply. This limited warranty is, except for consumer purchasers domiciled in Quebec, governed by the laws of the Province in Canada in which the purchaser has purchased the Product. For consumer purchasers domiciled in Quebec this limited warranty is governed by the laws of Quebec.

WARRANTY PERIODS (calculated from the date of original purchase): Parts & Labour (exceptions noted)

Audio Product 1 year Blu-Ray Product 1 year LCD/LED TV 1 year Microwave Oven 1 year (magnetron - 4 additional years) Air Purifier 1 year 3D Glasses 1 year Wireless LAN Adapter 1 year Small home appliances 1 year

ENGLISH

To obtain the name and address of the nearest Authorized Sharp Service Centre or Dealer, or for more information on this Limited Warranty, Sharp Extended Warranty Offers, Sharp Canada Products or Accessory Sales, please contact Sharp:

By writing to Sharp Electronics Of Canada Ltd. at 335 Britannia Road East Mississauga, Ontario L4Z 1W9

Calling: at 905-568-7140

Visiting our Web site: www.sharp.ca

THIS LIMITED WARRANTY IS VALID ONLY IN CANADA

E-5

IMPORTANT SAFETY INSTRUCTIONS

When using electrical appliances, basic safety precautions should be followed, including the following:

WARNING

• Read all instructions before using the unit.

• Use only a 120 volt outlet.

• The air puriﬁer has a polarized plug (one blade is wider than the other). This plug will ﬁt in a polar-

ized outlet only one way. If the plug does not ﬁt into the outlet, reverse it. If it still does not ﬁt, contact a qualiﬁed electrician or service person.

• Do not use the unit if the power cord or plug is damaged or the connection to the wall outlet is loosened.

• Periodically remove dust from the plug.

• Do not insert ﬁngers or foreign objects into the air intake or air outlet.

• When removing the power plug, always hold the plug and never pull on the cord.

Electrical shock and/or ﬁre from a short circuit may occur as a result.

• Do not remove the plug when your hands are wet.

• Do not use this unit near gas appliances or ﬁreplaces.

• If the power cord is damaged, it must be replaced by the manufacturer, its service agent, a

Sharp Authorized Service Center or similarly qualiﬁed person in order to avoid a hazard.

• Do not operate when using aerosol insecticides or in rooms where there is oily residue, incense, sparks from lit cigarettes, chemical fumes in the air, or in locations where the unit may get wet, such as a bathroom.

• Be cautious when cleaning the unit. Strong corrosive cleansers may damage the exterior.

• Only a Sharp Authorized Service Center should service this air puriﬁer. Contact the nearest Service Center for any problems, adjustments, or repairs.

- To reduce the risk of electrical shock, ﬁre or injury to persons:

NOTE

If this air puriﬁer should cause interference to radio or television reception, try to correct the interfer-

ence by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation distance between the unit and radio/TV receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This product fulﬁls the requirement of the International standard CISPR 11. In conformity with this standard, this product is classiﬁed as group 2 class B equipment.

Group 2 means that the equipment intentionally generates radio-frequency in the form of electromagnetic radiation for electro-discharge machining equipment. Class B equipment means that the equipment suitable to be used in domestic establishments.

This product complies with the maximum allowable concentration of ozone of 0.050 parts per million

byvolume (ppmv) in a 24-hour period. The Health Canada Guideline 2010 recommends that the maximumexposure limit, based on an averaging time of 8 hours, is 0.020 ppmv or less when tested in

a sealed,controlled room approximately 30 m³.

- Radio or TV Interference

E-6

CAUTIONS CONCERNING OPERATION

• Do not block the intake and/or air outlet.

• Do not use the unit near or on hot objects, such as stoves or heaters or where it may come into contact with steam.

• Always operate the unit in an upright position.

• Always hold the handles on both sides of the unit when moving it. Holding the back panel when carrying may cause it to detach, thus dropping the unit and resulting

in bodily injury.

• Do not operate the unit without the ﬁlters properly installed.

• Do not wash and reuse the True HEPA ﬁlter and Deodorizing filter.

Washing will not improve ﬁlter performance, it may cause electric shock or malfunction.

• Clean the exterior with a soft cloth only.

Do not use volatile ﬂuids and/or detergents. The unit surface may be damaged or cracked. In addition, the sensors may malfunction as a result.

To reduce the risk of electric shock, this equipment has a polarized plug (one blade is wider than

•

the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the

outlet,reverse the plug. If it still does not fit, contact qualified personnel to install the proper outlet. Do not alter the plug in any way.

• Keep the unit away from water.

INSTALLATION GUIDELINES

• During the operation of the product, please place the unit at least 6.5ft. (2m) away from equipment utilizing electrical waves such as televisions, radios or wave clocks.

• Avoid a location where the sensor is exposed to direct breeze or draft.

The unit may not operate properly.

• Avoid use in locations where furniture, fabrics or other items may come in contact with and restrict the air intake and/or air outlet.

• Avoid use in locations where the unit is exposed to condensation or rapid temperature changes. (Use under appropriate conditions between 41 - 95˚F (5 - 35˚C) in the room.)

(If it is unavoidable please allow unit to stand for 1 hour before switching on.)

• Place on a stable surface with sufﬁcient air circulation.

When placing the unit on a heavily carpeted area, the unit may vibrate slightly.

• Avoid use in locations where grease or oily smoke is generated.

The unit surface may crack or the sensor may malfunction as a result.

• Place the unit about 1 ft. (30 cm) away from the wall in order to ensure proper airﬂow.

Placing the purifier 1ft. or more from wall will reduce dust buildup on wall surface.

(such as in a kitchen, etc.)

ENGLISH

FILTER GUIDELINES

• Follow the instructions in this manual for correct care and maintenance of the ﬁlters.Use only ﬁlters designed for this product.

E-7

PART NAMES

FRONT VIEW

BACK VIEW

Control Panel

Odor Sensor



Air Outlet

Handle

Main Unit

Sensor

HEPA Filter

Active Carbon Deodorizing Filter

Back Panel (Pre-filter)

Power Plug Power Cord

E-8

CONTROL PANEL

FAN SPEED button (indicator lights-green)

QUICK CLEAN MODE button (indicator light-green)

PLASMACLUSTER ION ( ) ON/OFF button (indicator light-blue) Light on : ON ; Light off : OFF

CHILD LOCK button (indicator light-green)

LIGHT CONTROL BRIGHT/DIM/OFF button

FILTER RESET button (indicator light-orange)

POWER ON/OFF button

ENGLISH

OFF TIMER button (indicator lights-green)

House Dust

Monitoring

Dust

DUST SENSOR

Green Yellow Red

Room Air

Clean

Dirty

Odor

Monitoring

Odor

ODOR SENSOR

Green Yellow Red

Room Odor

Weak

Strong

E-9

PREPARATION FOR

FILTER INSTALLATION

Remove the back panel

(pre-filter).

There are two filters in the main unit.

USE

Unplug the unit before installing or

adjusting the ﬁlters.

Back Panel (Pre-filter)

Take out the two filters

from the plastic bags.

The side marked with

FRONT shall face outward.

HEPA Filter Active Carbon Deodorizing Filter

HEPA Filter

Active Carbon Deodorizing Filter

The figure on the upper shows the installation order of the HEPA filter and the Active Carbon Deodorizing Filter.

No difference between the front side and back side of deodorizing filter.

Install the back panel

(pre-filter).

Click

E-10

OPERATION

CONTROL PANEL

FAN SPEED button

E-12 E-12

QUICK CLEAN MODE button

PLASMACLUSTER ION ( ) ON/OFF button

E-12

CLEAN AIR MODE

Press the POWER ON/OFF button on the display

• If the power cord was not unplugged between uses, the unit will automatically re-start at the previously selected settings.

CHILD LOCK button

E-11

LIGHT CONTROL BRIGHT/DIM/OFF button FILTER RESET button

(NORMAL OPERATION)

POWER ON/OFF button

E-11,12

OFF TIMER button

E-14

ENGLISH

E-13

Press the FAN SPEED BUTTON to select the

desired fan speed. (See E-12)

QUICK CLEAN MODE

QUICK CLEAN Mode releases high-density Plasmacluster ions.

By continuously discharging strong airﬂow cycles, the unit effectively removes airborne dust, pollen, mold and allergens from the air as they are drawn through the ﬁlter system.

Press the QUICK CLEAN MODE Button on the

display to select this mode.

When the operation ﬁnishes, the unit will return to the prior

operation.

E-11



OPERATION

FAN SPEED Button

Press the FAN SPEED Button to select the preferred fan settings. Indicator lights will show the speed currently

selected. Please note the fan speed cannot be adjusted

during the QUICK CLEAN Mode.

AUTO operation

The fan speed is automatically controlled depending on the amount of impurities in

the air. The sensors detect the impurities for efﬁcient air puriﬁcation.

POLLEN mode operation

MAX operation

MEDIUM operation

LOW operation

The unit will operate at High level for 10 minutes, then will alternated between MED and HIGH every 20 minutes.

The unit will operate at maximun fan speed .

The unit will operate at medium fan speed .

The unit will operate quietly using minimal air intake.

Plasmacluster ON/OFF Button

Press the Plasmacluster ON/OFF Button to turn Plasmacluster Ion Mode ON and OFF. When Plasmacluster is ON, both the Indicator Light and Plasmacluster Indicator Light on the front display turn on.

CHILD LOCK Button

When you want to prevent children or pets from changing operation.

To enable To disable

Beep Beep Beep

Press and hold 3 seconds or longer

POWER ON/OFF Button

Press the Power ON/OFF Button to turn the unit off or on.

E-12

NOTE

While CHILD LOCK is enabled, all functions of the control are locked.

OPERATION

LIGHT CONTROL BRIGHT/DIM/OFF button

Use when the light on the control panel is too bright.

Refer to the diagram to select the desired brightness on the front panel.

NOTE:

The lights on the front panel are brighter.

The lights on the front panel are darker.

The lights on the front monitor turn off.

The lights on the control panel are always brighter when first operatings.

ENGLISH

OFF TIMER button

When you want to set the auto shutdown time.

ENABLE DISABLE

(Running)

Each press will change the setting in the following sequence.

Beep Beep Beep

2h 4h 8h

Beep Beep

DISABLE

Beep BeepBeep

ADJUSTMENT OF SENSOR DETECTION SENSITIVITY

Set to ‘low” if the DUST MONITOR is constantly red to reduce sensitivity, and set to ‘high’ if the DUST MONITOR is constantly green to increase sensitivity.

With the unit OFF, press the Fan Speed Button for 3 seconds.

The Fan Speed Indicator Lights will display the currently set sensor sensitivity level. The factory setting is Standard, indicated by the MED light.

Press the Fan Speed Button to

set the desired sensor sensitivity.

Refer to the diagram on the right to select the desired sensor sensitivity level.

Press the Power OFF Button.

Note that if the Power OFF Button is not pushed within 8 seconds of adjusting sensor

sensitivity, the setting will be saved automatically. The sensor sensitivity setting will be saved even if the unit is subsequently unplugged.

Fan Speed Indicator Light

Sensor Detection sensitivity

High

Standard

Low

E-13

CARE AND MAINTENANCE

Before maintenance, be sure to shut down the unit and remove its power plug. [Otherwise, electric shock or injury may be caused.]

BACK PANEL (PRE-FILTER)

The indicator light is lit when it is time to maintain the back panel (pre-filter).

Service the back panel (pre-filter).

ROUTINE MAINTENANCE

Use a vacuum cleaner to remove the dust.

NOTE

Be careful not to apply too much force to the filter.

Once a month

The indicator light will be lit in one month if the unit works 24 hours a day.

ENGLISH

Service the filter while it is mounted.

Back Panel (Pre-Filter)

As-Needed MAINTENANCE

Back Panel (Pre-Filter)

Soak the back panel in water with a small amount of dish soap.

Rinse the back panel repeatedly with clean water to remove the solution residue.

Drip Dry the panel to remove excess water.

After maintenance, insert the power plug.

When the unit starts to run,press and hold

the FILTER RESET button for 3 seconds

or longer until the indicator light is off.

After maintenance, press and hold the FILTER RESET button for 3 seconds or longer to reset the operation time even if the indicator light is not lit.

Beep

E-14

To keep the unit clean and maintain its long life, we recommend regular care and maintenance.

MAIN UNIT

Surface cleaning

Remove the power plug, and then wipe the main unit with a soft cloth.

Never wash the main unit with water.

Do not use the following articles:

(Otherwise, surface scratch and internal liquid leakage may cause malfunction.)

Volatile oil

Thinner

Do not use volatile fluids or detergents.

Lapping

powder

Abluent

Bleach

Synthetic

detergent

Spraying

detergent

Steel wool

Ifthere are stubborn stains, wipe them off with a cloth moistened with water or warm water (below100℉).

Unplug

HEPA FILTER, ACTIVE CARBON DEODORIZING FILTER

When odor comes out from the air outlet or it is difficult to remove odor.

Clean both the HEPA filter and the Active Carbon Deodorizing Fi

HEPA Filter

Gently vacuum the dust.

Never wash the filter with water.

the performance of the filter may be degraded.)

Clean carefully

Put a piece of paper under the filter to keep dirt off the surrounding area.

(Otherwise,

Only clean the side marked with FRONT on the frame. Do not clean the side marked with BACK on the frame of the filter.

(Otherwise, the performance of the filter may be degraded.)

Remove the dust from the filter. Do not apply too much force because the filter may be damaged easily.

Active Carbon Deodorizing Filter

Never wash the filter with water.

the performance of the filter may be degraded.)

(Otherwise,

Clean both sides of the filter.

Please note that too much force may damage the filter.

Remove the dust on the filter.

Absorb the dust gently

Put a piece of paper under the filter to keep dirt off the surrounding area.

NOTE

Never expose the filter to direct sunlight. (Otherwise, the filter may lose effectiveness.)

E-15

CARE AND MAINTENANCE

FILTER REPLACEMENT GUIDELINES

Before maintenance, be sure to shut down the unit and remove its power plug. [Otherwise, electric shock or injury may occur.]

HEPA FILTER, ACTIVE CARBON DEODORIZING FILTER

Model

HEPA Filter

FZ-F60HFU

The filter cannot be washed with water.

ENGLISH

Active Carbon Deodorizing

FZ-F60DFU

The filter cannot be washed with water.

Filter

NOTE

Put a piece of paper under the filter during replacement to avoid getting the surrounding area dirty.

In harsh environments filter replacement should be more frequent.

Replacing the Filters

1. Replace filters according to the instructions provided with the replacement filters.

2. Use the date labels as a reminder for when the filters should be replaced.

Replacement and Maintenance Cycle

Filter Name

HEPA Filter

Active Carbon

Deodorizing Filter

According to Japan Electric Manufacture's Association JEM 1467, the Max service life is based on the equivalent condition of the smoke from 5 cigarettes per day whereby the dust collection/deodorization power is reduced by half compared with that of new filter.It is recommended to replace the filter more frequently under more severe conditions.

Maintenance

Cycle

When odor emanates from the air outlet

Max Service

Life

5 years

Replacement

Filter Model

FZ-F60HFU

FZ-F60DFU

Disposal of Filters

Please dispose of used filters according to any local laws and regulations.

HEPA filter materials:

· Filter: Polypropylene · Frame: Polyester

Active Carbon Deodorizing Filter Materials:

· Polyester, Rayon, Activated charcoal

E-16

TROUBLESHOOTING

Before calling for service, please review the Troubleshooting chart below, since the problem may notbe a unit malfunction.

The odor or smoke in room is not being reduced.

ODOR

Odor emanates from the air outlet.

SolutionProblem

Is the filter still wrapped in the plastic bag?

Take out the filter from the plastic bag.

Is the air flow diminished?

Clean the areas with in the following table:

Cleaning Areas

Back PanelMain Unit

Is the unit used in a room with strong smells? If the unit is used in the presence of strong smells such as cigarette smoke, the filters may smell . It is recommended to frequently ventilate the room where the air purifier is used. Clean the areas with in the following table, if odor persists, replace the filters.

Cleaning Areas

Back Panel retliF APEHtinU niaM

Active Carbon

Deodorizing Filter

Active Carbon

Deodorizing Filter

★

HEPA Filter

Reference

Page

E - 10

E - 14~15

INDICATOR LIGHT SOUND

The FILTER RESET indicator light is lit.

The FILTER RESET indicator light does not turn off.

Clicking or ticking sounds are heard.

Clean the areas with in the following table:

Cleaning Areas

Back Panel retliF APEHtinU niaM

After maintenance, press and hold the FILTER RESET

) bu

(BRIGHT/DIM/OFF

Clicking or ticking sounds may be audible when the unit isgenerating ions.

tton for 3 seconds or longer.

Active Carbon

Deodorizing Filter

E-17

E - 14

TROUBLESHOOTING

Doublecheck before you call for service.

The Indicator Light does not change.

DUST/ODOR SENSOR

The Indicator Light never turns green.

SolutionProblem

When starting operation, the sensor may not react instantly to dust and odors.

After the unit has been running for several minutes, the sensor sensitivity will become stable.

To test the sensors, shake a dusty cloth near the sensor opening to see if the light changes color.

If you switch the unit on when the room has a strong smell, the sensitivity of the odor sensor may be temporarily deteriorated.

Set Fan Speed to MED and run the unit for several hours.

The doors or windows may be open. A sealed environment is needed to maximize air cleaning performance.

Reference

Page

E - 13

ENGLISH

The Indicator Light switches its state frequently.

The Indicator Light is too bright.

Frequent door opening and closing or airflow and temperature changes may cause reactions.

Adjust the brightness of indicator lights. Press the Light Control (BRIGHT/DIM/OFF) button.

E - 13

E-18

SPECIFICATIONS

Model FP-F60U-W Power supply Fan Speed Adjustment MAX

Fan Speed (CFM)

CLEAN AIR

Recommended Room Size*

Rated Power (W)

Noise Level (dBA)

202

52.8

CADR (Dust/Smoke/Pollen)

Sensors

Filter type

Cord Length

Dimensions

Weight

The recommended room size is appropriate for operating the unit at maximum fan speed

Dust collection Deodorization

True HEPA with Microbial control

357mm (W) × 201mm (D) × 576mm (H)

14 in (W) × 7

120 V 60 Hz

MED LOW

111

39.4

280 sq.ft( 26m )

194/181/202

Dust/odor

Active Carbon Deodorizing

5.9 ft (1.8m)

12.1 lbs (5.5 kg)

in (D) × 22

26.3

in (H)

Standby Power

In order to operate the electrical circuits while the power plug is inserted in the wall outlet, this product consumes about 0.5 W of standby power. For energy conservation, unplug the power cord when the unit is not in use.

E-19

ENGLISH

Sharp FPF60UW Operation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual