Sharp UX-68, FO-78 Service Manual

Download

UX-68DE FO-78DE

No. 00ZUX68DE/SME

CHAPTER 1. GENERAL DESCRIPTION

[1] Specifications ............................................ 1-1

[2] Operation panel......................................... 1-2

[3] Refer to the service manual of UX-40DE. [4] Refer to the service manual of UX-40DE.

[5] Quick reference guide ............................... 1-8

CHAPTER 2. ADJUSTMENTS

[1] Adjustments............................................... 2-1

[2] Diagnostics and service soft switch .......... 2-2

[3] Troubleshooting...................................... 2-19

[4] Error code table....................................... 2-20

CHAPTER 3. MECHANISM BLOCKS

[1] Refer to the service manual of UX-40DE. [2] Refer to the service manual of UX-40DE.

CHAPTER 4. DIAGRAMS

[1] Block diagram ............................................4-1

[2] Wiring diagram .......................................... 4-2

[3] Point-to-point diagram............................... 4-3

CHAPTER 5. CIRCUIT DESCRIPTION

[1] Circuit description...................................... 5-1

[2] Circuit description of control PWB..............5-2

[3] Circuit description of TEL/LIU PWB .......... 5-9

[4] Circuit description of

power supply PWB............................5-12

[5] Circuit description of CIS unit...................5-12

CHAPTER 6. CIRCUIT SCHEMATICS AND PARTS LAYOUT

[1] Control PWB circuit ................................... 6-1

[2] TEL/LIU PWB circuit ................................. 6-9

[3] Power supply PWB circuit ...................... 6-13

[4] Operation panel PWB circuit ................... 6-15

CHAPTER 7. OPERATION FLOWCHART

[1] Refer to the service manual of UX-40DE. [2] Refer to the service manual of UX-40DE.

CHAPTER 8. OTHERS

[1] Refer to the service manual of UX-40DE. [2] Refer to the service manual of UX-40DE. PARTS GUIDE

CONTENTS

FACSIMILE

UX-68

MODEL FO-78

Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.

This document has been published to be used for after sales service only. The contents are subject to change without notice.

SHARP CORPORATION

SERVICE MANUAL

Illustration: UX-68

This service manual is omitted because it is partly common to UX-40DE of the service manual of the previous issue. Those common parts are to refer to the service manual of UX-40DE (00ZUX40DE/SME).

UX-68DE FO-78DE

(Danish) ADVARSEL !

Lithiumbatteri-Eksplosionsfare ved fejlagtig håndtering.

Udskiftning må kun ske med batteri af samme fabrikat og type.

Levér det brugte batteri tilbage til leverandoren.

(English) Caution !

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type

recommended by the equipment manufacturer.

Discard used batteries according to manufacturer’s

instructions.

(Finnish) VAROITUS

Paristo voi räjähtää, jos se on virheellisesti asennettu.

Vaihda paristo ainoastaan laitevalmistajan suosittelemaan

tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden

mukaisesti.

(French) ATTENTION

Il y a danger d’explosion s’ il y a remplacement incorrect

de la batterie. Remplacer uniquement avec une batterie du

même type ou d’un type recommandé par le constructeur.

Mettre au rébut les batteries usagées conformément aux

instructions du fabricant.

(Swedish) VARNING

Explosionsfare vid felaktigt batteribyte.

Använd samma batterityp eller en ekvivalent

typ som rekommenderas av apparattillverkaren.

Kassera använt batteri enligt fabrikantens

instruktion.

(German) Achtung

Explosionsgefahr bei Verwendung inkorrekter Batterien.

Als Ersatzbatterien dürfen nur Batterien vom gleichen Typ oder

vom Hersteller empfohlene Batterien verwendet werden.

Entsorgung der gebrauchten Batterien nur nach den vom

Hersteller angegebenen Anweisungen.

CAUTION FOR BATTERY REPLACEMENT

UX-68DE FO-78DE

CHAPTER 1. GENERAL DESCRIPTION

[1] Specifications

Automatic dialing: Rapid Key Dialing: 5 numbers

Speed Dialing: 35 numbers

Fax paper: Initial starter roll (included with machine):

10 m Recommended replacement roll: FO-20PR, 30m

Modem speed: 9600 bps with automatic fallback to lower

speeds

Transmission time* : Approx. 15 seconds Resolution: Horizontal: 8 dots/mm

Vertical:

Standard: 3.85 lines/mm Fine/Halftone: 7.7 lines/mm Super fine: 15.4 lines/mm

Automatic document feeder: 5 pages max. (80g/cm2 paper) Halftone (grayscale): 64 levels Display: 16-digit LCD display Compression scheme: MR, MH, Sharp (H2) Applicable telephone line: Public switched telephone network/PBX Compatibility: ITU-T (CCITT) G3 mode Input document size: Automatic feeding:

Width: 148 to 216 mm Length: 140 to 297 mm

Manual feeding:

Width: 148 to 216 mm Length: 140 to 600 mm

Effective scanning width: 210 mm max. Effective printing width: 210 mm max. Contrast control: Automatic/Dark selectable Reception modes: Fax, Tel, Tel/Fax, A.M. Copy function: Yes Telephone function: Yes (cannot be used if power fails) Noise emission: Less than 70 dBA (Measured

according EN 277779 (DIN 45635))

Power requirements: 220-230 V AC, 50 Hz Operating temperature: 5 - 35°C Humidity: Maximum: 85 % RH Power consumption: Standby: 2.6 W

Maximum: 115 W

Dimensions: Width: 304 mm

Depth: 236 mm

Height: 122 mm Weight: Approx. 2.6 kg * Based on ITU-T (CCITT) T est Chart #1 at standard resolution in Sharp

special mode, excluding time for protocol signals (i.e., ITU-T phase C time only).

Note: The facsimile machine is Year 2000 compliant.

As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for procduct improvement without prior notice. The performance specifications figures indicated are nominal values of production units. There may be some deviation from these values in individual units.

1 – 1

UX-68DE FO-78DE

[2] Operation panel

1. Zielwahltasten (Rapid Dial keys)

Press one of these keys to dial a fax number automatically.

2. AUFN. (REC/MEMO key)

Press this key to record a phone conversation or a message.

3. ZURÜCK (REPEAT key)

Press this key to repeat playback of a message.

4. WIEDERG./VOR (PLAY/SKIP key)

Press this key to play recorded messages. During playback, press it to skip forward to the next message.

5. LCD-Anzeige (Display)

This displays messages and prompts during operation and programming.

6. LÖSCHEN (DELETE key)

Press this key to erase recorded messages.

7. FUNKTION (FUNCTION key)

Press this key to select various special functions.

8. Taste LAUTSTÄRKE (VOLUME keys)

Press this keys to adjust the volume of the speaker when the SPEAKER key has been pressed, the volume of the ringer at all other times.

9. Zifferntasten (Number keys)

Use these keys to dial numbers, and enter numbers and letters when storing auto-dial numbers.

10. KURZWAHL (SPEED DIAL key)

Press this key to dial a fax or voice number using an abbreviated 2-digit Speed Dial number.

11. WAHLWDH. (REDIAL key)

Press this key to automatically redial the last number dialed.

12. Taste START/SPEICHER (START/MEMORY key)

Press this key to send or receive a document or to scan a document into memory before sending it.

13. Taste STOP (STOP key)

Press this key to cancel operation before it is completed.

14. KOPIE/HILFE (COPY/HELP key)

When a document is in the feeder, press this key to make a copy of a document. At any other time, press this key to print out the Help List, a quick reference guide to the opeation of your fax machine.

15. Taste AUFLÖSUNG/EMPFANGSART (RESOLUTION/RECEPTION MODE key)

When a document is in the feeder, press this key to adjust the resolution for faxing or copying. At any other time, press this key to select the reception mode (an arrow in the display will point to the currently selected reception mode).

16. LAUTSPR. (SPEAKER key)

Press this key to listen the line and fax tones through the speaker when faxing a document. Note: This is not a speakerphone. You must pick up the handset to talk with the other party.

17. ALPHAWAHL/R (SEARCH/R key)

Press this key to search for an auto-dial number, or, if you are on a P.B.X. extension, press this key to transfer a call.

18. BEDIENFELD ENTRIEGELN (Panel release)

Grasp this finger hold and pull toward you to open the operation panel.

TEL FAX

GHI

PQRS

JKL

ABC

DEF

MNO

WXYZ

TUV

STOP

KOPIE/

HILFE

START/

SPEICHER

FUNKTION

LAUTSTÄRKE

KURZWAHL

WAHLWDH.

ALPHAWAHL

LAUTSPR.

AUFLÖSUNG/

EMPFANGSART

654

TEL/FAX ANRUFB.

ABRUF

1 8 9 105 7

151413

1718

SYMBOLE

AUFN.

ZURÜCK

WIEDERG./VOR

LÖSCHEN

2 3

4 6

1 – 2

UX-68DE FO-78DE

1 – 8

[5] Quick reference guide

ENTERING YOUR NAME AND NUMBER

1. Press:

FUNKTION

Display shows: OWN NUMBER SET

2. Press:

3. Enter your fax number (max. of 20 digits) by pressing the number keys.

• T o insert a space between digits, press the # key . T o enter "+", press the

key.

• If you make a mistake, press the SPEED DIAL key to backspace and clear the mistake.

4. Press:

5. Enter your name by pressing the appropriate number keys as shown below.

• T o enter two letters in succession that require the same key , press the SPEAKER key after entering the first letter.

SENDING FAXES

AUFLÖSUNG/

EMPFANGSART

FAX

TEL

FAX

TEL

05—NOV 10:30

ANRUFB.

TEL/FAX

ANRUFB.

TEL/FAX

05—NOV 10:30

FAX

TEL

FAX

TEL

05—NOV 10:30

ANRUFB.

TEL/FAX

ANRUFB.

TEL/FAX

05—NOV 10:30

START/

SPEICHER

Place your document (up to 5 pages) face down in the document feeder.

Normal Dialing

1. Lift the handset or press

2. Dial the fax number.

3. Wait for the reception tone (if a person answers, ask them to press their Start key).

4. Press:

Rapid Key Dialing

Press the appropriate Rapid Key. Transmission will begin automatically.

Speed Dialing

1. Press:

2. Enter 2-digit Speed Dial number.

3. Press:

RECEIVING FAXES

Press the RESOLUTION/RECEPTION MODE key until the arrow in the display points to the desired reception mode (make sure the document feeder is empty).

LAUTSPR.

KURZWAHL

FAX mode: The fax machine automatically answers on the set number of rings and receives the incoming document.

TEL mode:

TEL/FAX mode: This mode is convenient for receiving both faxes and voice calls.

When a call comes in, the fax will detect whether it is a voice call (including manually dialed fax transmissions), or an automatically dialed fax.

A.M. mode: Select this mode when you go out to receive both voice messages and faxes.

SETTING THE DATE AND TIME

1. Press: Display shows: DATE & TIME SET

2. Press:

3. Enter two digits for the Day (01 through 31).

4. Enter two digits for the Month (01 through 12).

5. Enter four digits for the Year (Ex: 2000).

6. Enter two digits for the Hour (01 through 23).

7. Enter two digits for the Minute (00 through 59).

8. When finished, press:

STORING AND CLEARING AUTO DIAL NUMBERS

1. Press: Display shows: FAX/TEL # MODE

2. Press 1 to store a number or 2 to clear a number.

3. Enter a 2-digit Speed Dial number (from 01 to 05 for Rapid Key Dialing, or 06 to 40 for Speed Dialing) (If you are clearing a number, go to Step 7.)

4. Enter the full fax/telephone number.

5. Press:

6. Enter the name of the location by pressing number keys (Refer to the letter entry table in

ENTERING YOUR NAME AND NUMBER

7. Press:

A = B =

C =

D =

E =

F =

G =

H =

I =

J =

K =

L =

M =

N =

O =

P =

Q = R =

S =

T = U =

V =

W =

X =

Y =

Z =

SPACE =

• To change case, press the REDIAL key. Press # or

to scroll through symbols and special characters.

6. When finished, press:

START/

SPEICHER

STOP

FUNKTION

Beep

START/

SPEICHER

RECEIVING

START/

SPEICHER

START/

SPEICHER

START/

SPEICHER

STOP

START/

SPEICHER

START/

SPEICHER

STOP

START/

SPEICHER

START/

SPEICHER

UX-68DE FO-78DE

M E M O

1 – 9

UX-68DE FO-78DE

CHAPTER 2. ADJUSTMENTS

[1] Adjustments

General

Since the following adjustments and settings are provided for this model, make adjustments and/or setup as necessary.

1. Adjustments

Adjustments of output voltage (FACTORY ONLY)

1. Install the power supply unit in the machine.

2. Set the recording paper and document.

3. When the document is loaded, power is supplied to the output lines. Confirm that outputs are within the limits below.

Output voltage settings

2. IC protectors replacement

ICPs (IC Protectors) are installed to protect the motor driver circuit. ICPs protect various ICs and electronic circuits from an overcurrent condition.

The location of ICPs are shown below:

1DG 2 +5V 3MG 4MG 5 +24V 6 +24V 7DG 8 PSAVE

2 – 1

TEL/LIU PWB

POWER SUPPLY PWB

CNL IUA

CN2

CNPW

CONTROL PWB

CNL IUB

CNLIUB

CNLIUA

Output V oltage limits

+5V 4.75V ∼ 5.25V

+24V 24.0V ∼ 26.0V

Connector

No. CNPW

Pin No.

CNLIUA

CNPW

CONTROL PWB

(TOP SIDE)

CNMT

FU100

CNLIUB

(1)FU100 (KAB2402) is installed in order to protect IC’s from an over-

current generated in the motor drive circuit. If FU100 is open, replace it with a new one.

3. Settings

Setting is not required since the required mode is TONE ONLY.

UX-68DE FO-78DE

[2] Diagnostics and service soft switch

1. Operating procedure (1) Entering the diagnostic mode

Press FUNC → 9 → → 8 → # → 7 , and the following display will appear. ROM Ver. FPB0 After 2 sec: DIAG MODE

FPB0 Then press the START key and country name selected by country select will appear. Select the desired item with the key or the # key or select

with the direct key. Enter the mode with the START key. (Diag•specifications)

If the diag mode cannot be set, repeat the diag mode operation, performing the following operation. After the power is turned on and "WAIT A MOMENT" is indicated, press the STOP key.

In relation with the process response (request from Production Engineering) "WAIT A MOMENT" clock indication may appear depending on STOP key timing. If the STOP key is held down, "MEMOR Y CLEAR?" appears.

FUNC

DIAG MODE

9 8 7

START —Soft switch mode START

AROM & RAM check

START

—Aging mode

START

—Panel check mode

START

BCheck pattern

START CSignal send mode

START

KEY

STOP

KEY

"Power ON"

Memory clear (Work + Backup)

FPB0

START —Memory clear

Shading mode

START START

All black mode

START

Auto feeder mode

START

Message print

Flash memory check

START

—

START

Flash memory clear

—

START

Country selct

—

2 – 2

2. Diagnostic items

ITEM DIRECT

No. key

Contents Function

1 — SOFT SWITCH MODE Soft switches are displayed and changed. List can be output. 2 A ROM & RAM CHECK ROM is sum-checked, and RAM is matched. Result list is output. 3 — AGING MODE 10 sheets of check patterns are output every 5 minutes per sheet. 4 — PANEL CKECK MODE Panel keys are tested. Result list is output. 5 B CHECK PATTERN 2 sheets of check patterns are output. 6 C SIGNAL SEND MODE Various signals of FAX communication are output. 7 — MEMORY CLEAR Back-up memory is cleared, and is set at delivery. 8 — SHADING MODE Shading compensation is performed in this mode.

9 D ALL BLACK PRINT To check the print head, whole dots are printed over the interval of 2 m. 10 E AUTO FEEDER MODE Insertion and discharge of document are tested. 11 — MESSAGE PRINT The display message of each language is printed out together with the English equivalent. 12 —

FLASH MEMORY CHECK

Checks flash memory write/read.

13 —

FLASH MEMORY CLEAR

Checks flash memory clearing.

14 — COUNTRY SELECT The software parameter that it agreed in each country name is set up.

UX-68DE FO-78DE

3. Diagnostic items description

3. 1. Soft switch mode

The soft switches are provided so that each operation mode can be set by using the operation panel.

In this mode, these switches can be checked and set. The contents of these switches are backed up. The available soft switches are SW-A1 to SW-K1. The content of soft switches is shown in page 2-5 to 2-18. The contents are set to factory default settings.

3. 2. ROM & RAM check

ROM executes the sum check, and RAM executes the matching test. The result will be notified with the number of short sounds of the buzzer as well as by printing the ROM & RAM check list. Number of short sounds of buzzer 0 → No error

1 → ROM error 2 → RAM error (32Kbyte)

3. 3. Aging mode

If any document is first present, copying will be executed sheet by sheet. If no document is present, the check pattern will be printed sheet by sheet. This operation will be executed at a rate of one sheet per 5minutes, and will be ended at a total of 10 sheets.

3. 4. Panel check mode

This mode is used to check whether each key operates properly or not. Press the key on the operation panel, and the key will be displayed on the display. Therefore, press all keys. At this time,finally press the ST OP key.

When the STOP key is pressed, the keys which are not judged as "pressed" will be printed on the result list.

• LED part of the contact image sensor (CIS) is kept on during the term from when "STAR T" of the panel test mode to end with the STOP key .

3. 5. Check pattern

This mode is used to check the status of print head. Two sheets of check pattern are printed. The following information of check pattern is printed.

Vertical stripes (alternate white and black lines) Approx. 35 mm

Full black Approx. 70 mm

Full white Approx. 35 mm

3. 6. Signal send mode

This mode is used to send various signals to the circuit during FAX communication. Every push of START key sends a signal in the following sequence. Moreover, the signal sound is also output to the speaker when the line monitor of the soft switch is on.

[1] No signal (CML signal turned on) [2] 9600bps [3] 7200bps [4] 4800bps [5] 2400bps [6] 300bps (FLAG) [7] 2100Hz (CED) [8] 1100Hz (CNG) [9] Pseudo Ring (models with auto TEL/FAX changeover function) [10] END

3. 7. Memory clear

This mode is used to clear the backup memory and to reset to the factory default settings. The content of each setting will be cleared.

Note: Be sure to execute the memory clear mode whenever you change

the country select setting. The default settings of the soft switches vary according to the destinations. Therefore, if you do not execute the memory clear after changing the country select setting, some functions may not work.

3. 8. Shading mode

The mode is used for the shooting compensation. For reading, set up the special original paper.

The shooting compensation memorizes the reference data of white and black for reading.

Moreover, the memorized data is not erased even if memory clear mode is executed.

3. 9. All black print

This mode is used to check the state of the printing head and intentionally overheat it. Whole dots are printed over the interval of 2 m. If it is overheated or the printing sheet is jammed, press STOP key for the end.

3. 10. Auto feeder mode

In this mode, a document is inserted and discharged to check the auto feed function.

After this mode is started, set a document, and the document feed will be automatically tested.

2 – 3

RANK 0 or 1

Note: There is a selection RANK 0 or 1 depending on resistance value of the thermal head. RANK 0 or RANK 1 is printed at the tail of check pattern to identify.

UX-68DE FO-78DE

3. 11. Message print

Used to print the displayed message of communication for translate each language.

3. 12. Flash memory check

Data is written into and read from the flash memory to check the data conformity. When the unit enters this mode, the check is started.

3. 13. Flash memory clear

Data in the flash memory is cleared (memory clear). When the unit enters this mode, the check is started. *Operation of hardware and signal in the flash memory check mode and flash memory clear mode, and the result of check. The result is announced by the buzzer beeps. The result of check is printed. Beeps

0 → No error 1 → Memory error

2 – 4

Press

FUNCTION

9 8 7 START START

Press FUNCTION key.

Press key.

Bit1 - 8 are set.

Soft SW-A2 - SW-K1 are set.

S F T SW-A1 = 1 0 0 0 0 0 0 0 S F T SW-A1 = 1 0 0 0 0 0 0 0 S F T SW-A1 = 1 0 0 0 0 0 0 0 S F T SW-A1 = 1 0 0 0 0 0 0 0

S F T SW-A2 = 0 0 0 0 0 0 0 0 S F T SW-K1 = 0 0 0 0 0 0 0 0

Press key during setting.

To finish the settings halfway between SW-A1 and SW-K1, press the STOP key. In this case, the setting being done to the SW No. on display will be nullified while settings done to the preceding SW Nos. remain in effect.

The soft switch mode is terminated.

S F T SW-A1 = 0 0 0 0 0 0 0 0

START

DATA No. 1 2 3 4 5 6 7 8

When the COPY key is pressed, the contents of soft switches are printed.

3. 14. Country select

This mode is used to set line connecting parameters which correspond to each destination.

When the country select mode is selected, and then the START key is pressed, the destination (country name) currently set will be displayed.

By pressing the # or key, selectable destinations (country names) are displayed. When the destination (country name) you want to choose is displayed, press the STAR T key . Each parameter will be stored in RAM.

Destinations (Country names) you can select are as follows:

COUNTRY NAME AUSTRIA (AT) GERMANY (DE) FRANCE (F)

Note: Be sure to execute the memory clear mode whenever you

change the country select setting. The default settings of the soft switches vary according to the destinations. Therefore, if you do not execute the memory clear after changing the country select setting, some functions may not work.

Do not set a country select setting which is different from that of the destination of the machine. Some functions will not work because the function and the PWB specifications are different.

4. How to make soft switch setting

To enter the soft switch mode, press the following key entries in sequence.

UX-68DE FO-78DE

1 Protect from echo No Yes 0 2 Forced 4800bps reception Yes No 0 3 Footer Print Yes No 0

4 Length limitation of copy/send/receive No limit Copy/Send:60cm 0

Receive:1.5m 5 CSI transmission Not transmitted Transmitted 0 6 DIS receive acknowledgement during G3 Twice NSF:Once 0

transmission DIS:Twice

7 Non modulated carrier for V29 transmission Yes No 0

mode

8 Reserved 0

Modem speed V.29 V.27 ter

9600bps 7200bps 4800bps 2400bps

1 No. 1 0 0 0 0 0 2 No. 2 0 0 0 0 0 3 No. 3 0 1 1 0 0

4 No. 4 1 1 0 0 1 5 Reserved 0

6 H2 mode No Yes 0 7 Communication error treatment in RTN No communication error Communication error 0

sending mode(Reception)

8 CNG transmission No Yes 0

CED tone signal interval 1000ms 750ms 500ms 75ms

1 No. 1 1 1 0 0 0 2 No. 2 1 0 1 0 0 3 MR Coding No Yes 0 4 Reserved 0

5 Reserved 0 6 Reserved 0

7 Reserved 0 8 Reserved 0

1 Signal Transmission level Binary input 0 2 (0~-31 dBm setting by 1dBm step) No. = 16 8 4 2 1 1 3 1 2 3 4 5 0 4 0 1 0 0 0 0 5 0 6 Protocol monitor(Error print) Printed at com. error Not printed 0

7 Protocol monitor Yes No 0 8 Line monitor Yes No 0

Digital equalization setting(Reception) 7.2km 0km

1 No. 1 1 0 1 2 No. 2 1 0 1

Digital equalization setting(Transmitter) 7.2km 0km

3 No. 3 1 0 0 4 No. 4 1 0 0

Digital equalization setting(Reception 7.2km 0km

5 for Caller ID) No. 5 1 0 0 6 No. 6 1 0 0

7 Error criterion 10 ~ 20 % 5 ~ 10 % 0 8 Anti junk fax check Yes No 1

5. Soft switch description

• Soft switch

SW NO.

DATA

NO.

ITEM

Switch setting and function

2 – 5

Remarks

Initial

setting

UX-68DE FO-78DE

1 Auto gain control(MODEM) Enable Disable 1 2 End Buzzer Yes No 1 3

Disconnect the line when DIS is received in RX mode

No Yes 1 4 Equalizer freeze control(MODEM) On Off 0 5 Equalizer freeze control 7200 bps only No Yes 0

6 CNG transmission in manual TX mode Yes No 1 7

Initial compression scheme for sharp fax in TX mode

MR mode H2 mode 0 8 Modem speed automatic down when RX Yes No 0

level is under -40dBm EOL detect timer 5 seconds 13 seconds 20 seconds25 seconds

1 No. 1 0 0 1 1 0 2 No. 2 0 1 0 1 1 3 Reserved 0

4 Reserved 0 5 Reserved 0

6 Reserved 0 7 Reserved 0

8 Reserved 0 1 Reserved 0 2 Auto dial fax transmission by REDIAL key Yes No 0

3 Reserved 0 4 Recall interval Binary input 0

5 (0~15.5min setting by 0.5min step) No. = 16 8 4 2 1 1 6 4 5 6 7 8 0 7 0 1 0 1 0 1 8 0 1 Recall times(0~15times setting) Binary input 0 2 No. = 8 4 2 1 0

3 1 2 3 4 1 4 0 0 1 0 0 5 Dial tone detection(Before auto dial) No Yes 1 6 Reserved 0

7 Busy tone detection(After auto dial) No Yes 1 8 Busy tone detection pulse number 4 pulses 2 pulses 0

(After auto dial) Waiting time after dialing

45 seconds 55 seconds 90 seconds 140 seconds

1 No. 1 0 0 1 1 1 2 No. 2 0 1 0 1 0 3 PBX connection Yes No 0 OPTION 4 Reserved 0

PBX recall function(R key select) NO OPERATION FLASH

5 No. 5 0 1 1 6 No. 6 0 1 1

PBX select ID FLASH OPTION

7 No. 7 0 1 0 8 No. 8 0 1 0 1 Dial pausing(sec/pause) 4 sec 2 sec 1

2 Dial mode Tone Pulse 1 3 Pulse → Tone change function by key Enable Disable 1

4 Dial pulse make/break ratio(%) 40/60 33/67 1

Auto dial mode Delay timer of before line

0 second 1.5 seconds 3.0 seconds 4.5 seconds

5 connect No. 5 0 0 1 1 0 6 No. 6 0 1 0 1 1 7 Reserved 0

8 Reserved 0

SW NO.

DATA

NO.

ITEM

Switch setting and function

2 – 6

Remarks

Initial

setting

UX-68DE FO-78DE

Auto dial mode Delay timer of after line 1.7s 2.0s 2.5s 3.0s 3.6s 4.0s 5.5s 7.0s

1 connect No. 1 0 0 0 0 1 1 1 1 1 2 No. 2 0 0 1 1 0 0 1 1 0 3 No. 3 0 1 0 1 0 1 0 1 1 4

Fax signal detection after telephone mode dial

Yes No 0

Recalling fixed only one time when dialing was

Yes No 0

unsuccessful without detecting busy tone signal 6 Reserved 0 7 Reserved 0

8 Reserved 0 1 DTMF signal transmission level Binary input 1

2 (Low frequency 0~15.5dBm setting No. = 16 8 4 2 1 0 3 by 0.5dBm step) 1 2 3 4 5 0

4 1 0 0 0 1 0 5 1

6 Reserved 0 7 Reserved 0

8 Reserved 0 1 DTMF signal transmission level Binary input 0 2 (High frequency 0~15.5dBm setting No. = 16 8 4 2 1 1 3 by 0.5dBm step) 1 2 3 4 5 1

4 0 1 1 0 0 0 5 0

6 Reserved 0 7 Reserved 0

8 Reserved 0

Reading Slice(Binary) Factory Dark Light Daker in

setting dark

1 No. 1 0 0 1 1 0 2 No. 2 0 1 0 1 0

Reading Slice(Half tone) Factory Dark Light Daker in

setting dark

3 No. 3 0 0 1 1 0 4 No. 4 0 1 0 1 0 5 Line density selection Fine Standard 0 6 Reserved 0

7 MTF correction in half tone mode No Yes 0 8 Reserved 0

1 Number of rings for auto receive Binary input 0 OPTION 2 (0~15rings setting) No. = 8 4 2 1 0 3 1 2 3 4 1

4 0 0 1 0 0 5 Automatic swiching manual to auto receive Yes No 0

function

CI detect frequency

As PTT 11.5Hz 13.0Hz 20.0Hz

6 No. 6 0 0 1 1 0 7 No. 7 0 1 0 1 0 8 Reserved 0

2 – 7

SW NO.

DATA

NO.

ITEM

Switch setting and function

Remarks

Initial

setting

UX-68DE FO-78DE

1 Reserved 0 2 Reserved 0

3 Reserved 0 4 Reserved 0

5 Reserved 0 6 Caller ID function Yes No 0 OPTION 7 Reserved 0 8 Reserved 0 1 CI off detection timer Binary input 0 2 (0~1550ms setting by 50ms step) No. = 16 8 4 2 1 1 3 1 2 3 4 5 1

4 0 1 1 1 0 1 5 0

6 Reserved 0 7 Reserved 0 8 Reserved 0 1 DTMF type Caller ID RX level Binary input 1 2 (0~-44dBm setting by 1dBm step) No. = 32 16 8 4 2 1 0 3 1 2 3 4 5 6 1

4 1 0 1 1 0 0 1 5 0

6 0 7 Reserved 0

8 Reserved 0

Pseudo ringing time at the TEL/FAX

9sec 15sec 30sec 60sec 90sec 120sec 150sec 180sec

1 automatic switching mode No. 1 0 0 0 0 1 1 1 1 0 2 No. 2 0 0 1 1 0 0 1 1 1 3 No. 3 0 1 0 1 0 1 0 1 0 4 Number of CNG signal detection at the Twice Once 1

TEL/FAX automatic switching mode

5 CNG detect time at TEL/FAX mode 3 sec 5 sec 0 6 Post answer tone(TEL/FAX mode) No Yes 1

7 Type of post answer tone LA-SI-DO tone 800Hz single tone 0 8 Pseudo ringer ON/OFF cycle 1 sec ON / 4 sec OFF 1 sec ON / 2 sec OFF 1

1 Pseudo ringer sound output level to the line Binary input 1 2 (0~-15dBm setting by 1dBm step) No. = 8 4 2 1 0 3 1 2 3 4 1

4 1 0 1 0 0

Post answer tone transmission level Binary input 5 (0~-15dBm setting by 1dBm step) No. = 8 4 2 1 1 6 5 6 7 8 0 7 1 0 0 1 0

8 1 1 Reserved 0

Action select when DTMF "#" is received during

A.M. Remote

phone/fax automatic switching mode

No Action No Action

operation

Disconnect line 2 No. 2 0 0 1 1 0 3 No. 3 0 1 0 1 0

4 Reserved 0 5 Reserved 0

6 Reserved 0 7 Reserved 0

8 Reserved 0

SW NO.

DATA

NO.

ITEM

Switch setting and function

2 – 8

Remarks

Initial

setting

UX-68DE FO-78DE

DTMF detection time 50ms 80ms 100ms 120ms 1 No. 1 0 0 1 1 0 2 No. 2 0 1 0 1 0

3 Protection of remote reception(5 ) Yes No 0

detection 4 Remote reception with GE telephone Compatible Not compatible 1 5 Remote operation code figure by external Binary input 0 OPTION

6 TEL (0~9) No. = 8 4 2 1 1 7 5 6 7 8 0

8 0 1 0 1 1 1 CNG detection in STAND-BY mode Yes No 1 OPTION

Number of CNG detect(AM mode) 1 pulse 2 pulses 3 pulses 4 pulses 2 No. 2 0 0 1 1 0 3 No. 3 0 1 0 1 1

Number of CNG detect(STAND-BY mode) 1 pulse 2 pulses 3 pulses 4 pulses 4 No. 4 0 0 1 1 0 5 No. 5 0 1 0 1 1

6 Reserved 0 7 Reserved 0

8 Reserved 0 1 Reserved 0

2 Reserved 0 3 Reserved 0

4 Reserved 0 5 Reserved 0

6 Reserved 0 7 Reserved 0

8 Reserved 0 1 Reserved 0

2 Reserved 0 3 Reserved 0

4 Reserved 0 5 Reserved 0

6 Reserved 0 7 Reserved 0

8 Reserved 0 1 Reserved 0

2 Reserved 0 3 Reserved 0

4 Reserved 0 5 Reserved 0

6 Reserved 0 7 Reserved 0 8 Reserved 0

1 Quiet detect level setting Binary input 1 2 (0~-44dBm setting by 1dBm step) No. = 32 16 8 4 2 1 0 3 1 2 3 4 5 6 1

4 1 0 1 1 0 0 1 5 0

6 0 7 Fax switching when A.M. full Yes No 0 OPTION

8 Reserved 0

SW NO.

DATA

NO.

ITEM

Switch setting and function

2 – 9

Remarks

Initial

setting

UX-68DE FO-78DE

1 Busy tone continuous sound detect time 5sec 10sec 1 2 Busy tone detect continuation sound detect No Yes 1

during OGM

3 Busy tone detect continuation sound detect No Yes 0 4 Busy tone detect intermittent sound detect No Yes 1

during OGM

5 Busy tone detect intermittent sound detect No Yes 0

Busy tone detection pulse number 2pulses 4pulses 6pulses 10pulses 6 No. 6 0 0 1 1 0 7 No. 7 0 1 0 1 1

8 Reserved 0 1 Reserved 0

2 Reserved 0 3 Reserved 0

4 Reserved 0 5 Reserved 0 6 Reserved 0

7 Reserved 0 8 Reserved 0

ICM recording time 4min 15s 30s 60s OPTION 1 No. 1 0 0 1 1 0 2 No. 2 0 1 0 1 0

A.M. Quiet time 1 2s 3s 4s 5s 3 No. 3 0 0 1 1 0 4 No. 4 0 1 0 1 0

A.M. Quiet time 2 0s 1s 2s 3s 5 No. 5 0 0 1 1 1 6 No. 6 0 1 0 1 0

7 Key input buzzer on/off switch On Off 0

(Two way recording mode) 8 Reserved 0

A.M. Quiet detect time Binary input 1 No. = 16 8 4 2 1 0 2 1 2 3 4 5 0 3 0 0 1 1 0 1

4 1 5 0

6 Reserved 0 7 Reserved 0

8 Reserved 0 1 Two way alarm Yes No 1

2 Max OGM record time 15s 60s 0 3 Two way record function Disable Enable 0

4 Toll saver Disable Enable 0 OPTION 5 FAX reception in case of detecting No sound Yes No 1

detect after ICM recording 6 Reserved 0

7 Reserved 0 8 Transfer dial recall Disable Enable 0

NO.

DATA

NO.

ITEM

Switch setting and function

2 – 10

Remarks

Initial

setting

UX-68DE FO-78DE

AGC Maximum Gain (line) 10~25dB (1dB step)

Binary input 1 No. = 8 4 2 1 1 2 1 2 3 4 1 3 1 1 0 0 0

4 0

AGC Maximum Gain (mic) 10~25dB (1dB step)

Binary input 5 No. = 8 4 2 1 1 6 5 6 7 8 1 7 1 1 1 1 1

8 1

AGC Eref access code (line) -0~-30dB (2dB step)

Binary input 1 No. = 8 4 2 1 1 2 1 2 3 4 1 3 1 1 0 1 0

4 1

AGC Eref access code (mic) -0~-30dB (2dB step)

Binary input 5 No. = 8 4 2 1 1 6 5 6 7 8 1 7 1 1 1 1 1

8 1

AGC

Gain Adaptation Threshold (line) Binary input 1 No. = 8 4 2 1 1 2 1 2 3 4 1 3 1 1 1 1 1

4 1

AGC

Gain Adaptation Threshold (mic) Binary input 5 No. = 8 4 2 1 1 6 5 6 7 8 1 7 1 1 1 1 1

8 1

AGC

Slew Rate (line) Slow Normal Little fast Fast 1 No. 1 0 0 1 1 0 2 No. 2 0 1 0 1 1

AGC

Slew Rate (mic) Slow Normal Little fast Fast 3 No. 3 0 0 1 1 0 4 No. 4 0 1 0 1 1

5 Reserved 0 6 Reserved 0

7 Reserved 0 8 Reserved 0

OGM/ICM output level (0~-31dBm setting by Binary input 1 1dBm step) No. = 16 8 4 2 1 0 2 1 2 3 4 5 0 3 0 0 1 0 1 1

4 0 5 1

6 AM OGM announce only mode Yes No 0 OPTION 7 Reserved 0 8 Reserved 0

SW NO.

DATA

NO.

ITEM

Switch setting and function

2 – 11

Remarks

Initial

setting

UX-68DE FO-78DE

1 Sender’s phone number setting Cannot change Change allowed 0 2 Summer time No Yes 0

Ringer volume Off Low Middle High OPTION

3 No. 3 0 0 1 1 1 4 No. 4 0 1 0 1 0 5 Reserved 0

6 Reserved 0 7 Polling key Yes No 0 OPTION 8 Reserved 0

1 Reserved 0 2 Reserved 0

Speaker volume Very Low Low Middle High Very High OPTION

3 No. 3 0 0 0 0 1 0 4 No. 4 0 0 1 1 0 1 5 No. 5 0 1 0 1 0 0 6 Speaker monitor function Yes No 1

7 Saving energy start timing 5sec 180sec 0 8 Saving energy mode Enable Disable 1

Communication results printout Error Send only Always No print OPTION

(Transaction report)

No. 1 0 0 0 0 0 2 No. 2 0 0 1 1 0 3 No. 3 0 1 0 1 0 4 Time format 12 hour 24 hour 0

5 Date format Month-Day-Year Day-Month-Year 0 6 Reserved 0

7 Reserved 0 8 Reserved 0

1 Entering diag mode by pressing SPEED key Yes No 0 2 Reserved 0 3 Reserved 0

4 Reserved 0 5 Reserved 0

6 Reserved 0 7 Reserved 0

8 Reserved 0

NO.

DATA

NO.

ITEM

Switch setting and function

2 – 12

Remarks

Initial

setting

UX-68DE FO-78DE

• Soft switch function description

SW-A1 No. 1 Protect from echo

Used to protect from echo in reception.

SW-A1 No. 2 Forced 4800BPS reception

When line conditions warrant that receptions take place at 4800 BPS repeatedly. It may improve the success of receptions by setting at 4800BPS. This improves the receiving document quality and reduces handshake time due to fallback during training.

SW-A1 No. 3 Footer print

When set to "1", the date of reception, the sender machine No., and the page No. are automatically recorded at the end of reception.

SW-A1 No. 4 Length limitation of copy/send/receive

Used to set the maximum page length. To avoid possible paper jam, the page length is normally limited to 0.6 meter for copy or transmit, and 1.5 meters for receive. It is possible to set it to "No limit" to transmit a long document, such as a computer print form, etc. (In this case, the receiver must also be set to no limit.)

SW-A1 No. 5 CSI transmission

(CSI TRANSMISSION) is a switch to set whether the machine sends or does not send the signal (CSI signal) informing its own telephone No. to the remote fax machine when information is received. When "nonsending" is set, the telephone No. is not output on the remote transmitting machine if the remote transmitting machine has the function to display or print the telephone No. of receiving machine, using this CSI signal.

SW-A1 No. 6 DIS receive acknowledgment during G3 transmission

Used to make a choice of whether reception of DIS(NSF) is acknowledged after receiving two DISs(NSFs) or receiving one DIS (two NSFs). It may be useful for overseas communication to avoid an echo suppression problem, if set to 1.

SW-A1 No. 7 Non modulated carrier for V29 transmission mode

Though transmission of a nonmodulated carrier is not required for transmission by the V29 modem according to the CCITT Recommendation, it may be permitted to a send nonmodulated carrier before the image signal to avoid an echo suppression problem. It may be useful for overseas communication to avoid an echo suppression problem, if set to 1.

SW-A1 No. 8 Reserved

Set to "0".

SW-A2 No. 1 ~ No. 4 Modem speed

Used to set the initial modem speed. The default is 9600BPS. It may be necessary to program it to a slower speed when frequent line fallback is encountered, in order to save the time required for fallback procedure.

SW-A2 No. 5 Reserved

Set to "0".

SW-A2 No. 6 H2 mode

Used to determine reception of H2 mode (15 sec transmission mode). When set to OFF , H2 mode reception is inhibited even though the transmitting machine has H2 mode function.

SW-A2 No. 7 Communication error treatment in RTN sending mode (Reception)

Used to determine communication error treatment when RTN is sent by occurrence of a received image error in G3 reception. When it is set to "1", communication error is judged as no error.

SW-A2 No. 8 CNG transmission

When set to "0", this model allows CNG transmission by pressing the Start key in the key pad dialing mode. When set to "1", CNG transmission in the key pad dialing mode cannot be performed. In either case, CNG transmission can be performed in the auto dial mode.

2 – 13

TX RX

CED

DIS

SW-A3 No. 1, No. 2 CED tone signal interval

For international communication, the 2100Hz CED tone may act as an echo suppression switch, causing a communication problem. Though SW-A3 No. 1 and No. 2 are normally set to 0, this selfing is used to change the time between the CED tone signal to eliminate the communication caused by echo.

SW-A3 No. 3 MR coding

Used to select the MR coding enable or disable.

SW-A3 No. 4 ~ No. 8 Reserved

Set to "0".

SW-A4 No. 1 ~ No. 5 Signal transmission level (0~-31 dBm setting by 1dBm step)

Used to control the signal transmission level in the range of -0dB to

-31dB. The factory setting is at -11dB(HK), -9dB(SG) (MODEM output).

SW-A4 No. 6 Protocol monitor (Error Print)

If set to "1", protocol is printed at communication error.

SW-A4 No. 7 Protocol monitor

Normally set to "0". If set to "1", communication can be checked, in case of trouble, without using a G3 tester or other tools. When communication FSK data transmission or reception is made, the data is taken into the buffer. When communication is finished, the data is analyzed and printed out. When data is received with the line monitor (SW4-No. 8) set to "1" the reception level is also printed out.

SW-A4 No. 8 Line monitor

Normally set to "0". If set to "1", the transmission speed and the reception level are displayed on the LCD. Used for line tests.

SW-A5 No. 1, No. 2 Digital equalization setting (Reception)

Line equalization when reception is to be set according to the line characteristics. Setting should be made according to distance between the telephone and the telephone company central switching station.

SW-A5 No. 3, No. 4 Digital equalization setting (Transmitter)

Line equalization when transmission is to be set according to the line characteristics. Setting should be made according to distance between the telephone and the telephone company central switching station.

SW-A5 No. 5, No. 6 Digital equalization setting (Reception for Caller ID)

Line equalization when reception for CALLER ID is to be set according to the line characteristics. Setting should be made according to distance between the telephone and the telephone company central switching station.

SW-A5 No. 7 Error criterion

Used to select error criterion for sending back RTN when receiving image data.

SW-A5 No. 8 Anti junk fax check

When using the Anti junk fax function, set to "1".

SW-A6 No. 1 Auto gain control(MODEM)

When this mode is enabled, if the reception signal level is under 31dBm, the modem itself controls the signal gain automatically.

SW-A6 No. 2 End buzzer

Setting this bit to 0 will disable the end buzzer (including the error buzzer/ on-hook buzzer).

UX-68DE FO-78DE

SW-A6 No. 3 Disconnect the line when DIS is received in RX mode

Bit1 = 0 : When DIS signal is received during RX mode, disconnect the

line immediately.

Bit1 = 1 : When DIS signal is received during RX mode, wait for the next

signal.

SW-A6 No. 4 Equalizer freeze control (MODEM)

This switch is used to perform reception operation by fixing the equalizer control of modem for the line which is always in unfavorable state and picture cannot be received. * Usually, the control is executed according to the state of line where the equalizer setting is changed always.

SW-A6 No.5 Equalizer freeze 7200BPS only

Setting which specifies SW-A6 No. 4 control only in condition of 7200BPS modem speed.

SW-A6 No. 6 CNG transmission in manual TX mode

When set to "1", fax transmit the CNG signal in case of manual transmissiom mode (User press the START key after waiting for the fax answering signal from handset or speaker).

SW-A6 No. 7 Initial compression scheme for sharp fax in TX mode

When set to "0", if the other fax is Sharp model, fax transmit the document by H2 mode. When set to "1", even if the other fax is Sharp model, fax transmit the document by MR mode.

SW-A6 No. 8 Modem speed automatic down when RX level is under

-40dBm

When set to "1", if fax signal level is under -40dBm during reception, machine selects the slower modem speed automatically. It is effective when noises occur on the received document due to the long distance communications.

SW-A7 No. 1, No. 2 EOL (End Of Line) detect timer

Used to make a choice of whether to use the 5 or 13 or 20 or 25 seconds timer for detection of EOL. This is effective to override communication failures with some facsimile models that have longer EOL detection.

SW-A7 No. 3 ~ No. 8 Reserved

Set to "0".

SW-B1 No. 1 Reserved

Set to "0".

SW-B1 No. 2 Auto dial fax transmission by REDIAL key

When set to "1", if original documents are set to the feeder and you press REDIAL key, machine will dial and transmit the ducuments automatically. When set to "0", operator needs to press the START key after FAX reception tone is heard.

SW-B1 No. 3 Reserved

Set to "0".

SW-B1 No. 4 ~ No. 8 Recall interval (0~15.5min setting by 0.5min step)

Choice is made for a redial interval for speed and rapid dial calls. Use a binary number to program this with 0.5min steps. If set to 0 accidentally, 0.5min will be assumed.

SW-B2 No. 1 ~ No.4 Recall times (0~15times setting)

Choice is made as to how many redials there should be.

SW-B2 No. 5 Dial tone detection (Before auto dial)

Used to set YES/NO of dial tone detection in auto dialing.

SW-B2 No. 6 Reserved

Set to "0".

SW-B2 No. 7 Busy tone detection (After auto dial)

Used to set YES/NO of busy tone detection after auto dialing.

SW-B2 No. 8 Busy tone detection pulse number (After auto dial)

Used for detection of busy tone in 2 or 4 pulses.

SW-B3 No. 1, No. 2 Waiting time after dialing

This is waiting time for the opponent's signals after dialing. 45 / 55 / 90 / 140 seconds settings are available.

SW-B3 No. 3 PBX connection

Used to select according to the connected line: PBX (Private Branch Exchange).

SW-B3 No. 4 Reserved

Set to "0".

SW-B3 No. 5, No. 6 PBX recall function (R key select)

Used to set the operation mode of PBX recall when the R key is pressed. Setting is made according to the type of PBX.

No. 5=1, No. 6=1:Time break recall (=Flash) is performed.

SW-B3 No. 7, No. 8 PBX select

Used to select the operation mode of PBX recall in auto dialing. No. 7=1, No. 8=1:Time break recall (=Flash) is performed before dialing.

No. 7=0, No. 8=0:The PBX ID digit is automatically added when dialing

to external line. PBX ID is up to 3 digits and entered in Option settings mode.

SW-B4 No. 1 Dialing pause (sec/pause)

Pauses can be inserted between telephone numbers of direct dial connection. Selection of 4 sec or 2 sec pause is available.

SW-B4 No. 2 Dial mode

When using the pulse dial, set to 0. When using the tone dial, set to 1.

SW-B4 No. 3 Pulse → Tone change function by key

When setting to 1, the mode is changed by pressing the key from the pulse dial mode to the tone dial mode.

SW-B4 No. 4 Dial pulse make/break ratio (%)

When using the 33% make ratio pulse dial, set to 0. When using the 40% make ratio pulse dial, set to 1.

SW-B4 No. 5, No. 6 Auto dial mode Delay timer of before line connect

Delay time between the dial key input and line connection under the auto dial mode.

2 – 14

RAPID A CML RELAY ON

DIALLING

No.5=0 No.6=0 : 0sec No.5=0 No.6=1 : 1.5sec No.5=1 No.6=0 : 3.0sec No.5=1 No.6=1 : 4.5sec

SW-B4 No. 7, No. 8 Reserved

Set to "0".

UX-68DE FO-78DE

2 – 15

SW-B5 No. 1 ~ No. 3 Auto dial mode Delay timer of after line connect

Delay time between the line connection and dial data output under the auto dial mode. This setting is available when dial tone detection(SW-B2 No. 5) is set to "NO".

RAPID A CML RELAY ON

DIAL DATA

No. 1 No. 2 No. 3

0 0 0 1.7sec 0 0 1 2.0sec 0 1 0 2.5sec 0 1 1 3.0sec 1 0 0 3.6sec 1 0 1 4.0sec 1 1 0 5.5sec 1 1 1 7.0sec

SW-B5 No. 4 Fax signal detects after telephone mode dial

When set to "1", if machine detects the fax answering signal after telephone calling (handset off-hook or speaker mode dial), machine starts to receive the documents automatically.

SW-B5 No. 5 Recalling fixed only one time when dialing was unsuccessful without detecting busy tone signal

When set to "1", if machine does not detect the busy tone after auto dialing and dialing is unsuccessful, machine will try to recall only one time.

SW-B5 No. 6 ~ No. 8 Reserved

Set to "0".

SW-B6 No. 1 ~ No. 5 DTMF signal transmission level (Low frequency 0~15.5dBm setting by 0.5dBm step)

The transmission level of DTMF signal is adjusted. (lower frequency)

00000: 0dBm

↓

11111: -15.5 dBm (-0.5dBm x 31)

SW-B6 No. 6 ~ No. 8 Reserved

Set to "0".

SW-B7 No. 1 ~ No. 5 DTMF signal transmission level (High frequency 0~15.5dBm setting by 0.5dBm step)

The transmission level of DTMF signal is adjusted. (higher frequency)

00000: 0dBm

↓

11111: -15.5 dBm (-0.5dBm x 31)

SW-B7 No. 6 ~ No. 8 Reserved

Set to "0".

SW-C1 No. 1, No. 2 Reading slice (Binary)

Used to determine the set value of reading density in standard/fine/super-fine mode. The standard setting is "00"(Factory setting is "00").

SW-C1 No. 3, No. 4 Reading slice (Half tone)

Used to determine the set value of reading density in half tone mode. The standard setting is "00"(Factory setting is "00").

SW-C1 No. 5 Line density selection

Used to set the transmission mode which is automatically selected when the Resolution key is not pressed. In the copy mode, however, the fine mode is automatically selected unless the Resolution key is manually set to another mode.

SW-C1 No. 6 Reserved

Set to "0".

SW-C1 No. 7 MTF correction in half tone mode

This allows selection of MTF correction (dimness correction) in the half tone mode. When "NO" (=1) is selected, the whole image becomes soft and mild. Clearness of characters will be reduced. Normally set to "YES" (=0).

SW-C1 No. 8 Reserved

Set to "0".

SW-D1 No.1 ~ No. 4 Number of rings for auto receive (0~15rings setting)

When the machine is set in the auto receive mode, the number of rings before answering can be selected. It may be set from one to nine rings using a binary number. Since the facsimile telephone could be used as an ordinary telephone if the handset is taken off the hook, it should be programmed to the user's choice. If the soft switch was set to 1, direct connection is made to the facsimile. If a facsimile calling beep was heard when the handset is taken off the hook, press the STAR T key and put the handset on the hook to have the facsimile start receiving. If it was set to 0 accidentally, receive ring is set to 1.

NOTE: If the machine is set to answer after a large number of rings, it

may not be able to receive faxes successfully. If you have difficulty receiving faxes, reduce the number of rings to a maximum of 5.

SW-D1 No. 5 Automatic switching manual to auto receive function

This soft switch is used to select whether the machine should switch to the auto receive mode after 5 rings in the manual receive mode or remain in the same way as SW-D1 No. 1, No. 2, No. 3 and No. 4 "0"1"0"1"(5 rings).

SW-D1 No. 6, No. 7 CI detect frequency

Detection frequency of ring signal for auto reception is set. When set to No. 6=0, No. 7=0, frequency is set to PTT recommendation.

When set to No. 6=0, No. 7=1, frequency is set to 11.5Hz or more. When set to No. 6=1, No. 7=0, frequency is set to 13.0Hz or more. When set to No. 6=1, No. 7=1, frequency is set to 20.0Hz or more.

SW-D1 No. 8 Reserved

Set to "0".

SW-D2 No. 1 ~ No. 5 Reserved

Set to "0".

SW-D2 No. 6 Caller ID Function

Used for Caller ID function.

SW-D2 No. 7, No. 8 Reserved

Set to "0".

UX-68DE FO-78DE

2 – 16

SW-D3 No. 1 ~ No. 5 CI off detection timer (0~1550ms setting by 50ms step)

Set the minimum time period of CI signal interruption which affords to be judged as a CI OFF section with 50ms steps. (Example)

400msec

2000msec

0 1 1 1 0 (50ms~14) : 700ms(CI interruption>700ms:Judged as a CI

OFF section) The section 1 is not judged as a CI OFF section, the CI signal A is counted as one signal. The section 2 is judged as a CI OFF section, the CI signal B is considered as the second signal.

0 0 1 1 1 (50ms~7) : 350ms(CI interruption>350ms:J udged as a CI

OFF section) The section 1 is judged as a CI OFF section, and the CI signal A is counted as two signals. The section 2 is judged as a CI OFF section, and the CI signal B is considered as the third signal.

SW-D3 No. 6 ~ No. 8 Reserved

Set to "0".

SW-D4 No. 1 ~ No. 6 DTMF type Caller ID RX level (0~-44dBm setting by 1dBm step)

This is used for DTMF type Caller ID detection level setting.

SW-D4 No. 7, No. 8 Reserved

Set to "0".

SW-E1 No. 1 ~ No. 3 Pseudo ringing time at the TEL/FAX automatic switching mode

Choice is made as to how long to rumble the dummy ringer on TEL/FAX automatic switching mode.

SW-E1 No. 4 Number of CNG signal detection at the TEL/FAX automatic switching mode

Used for detection of CNG in one tone or two tones in the TEL/FAX automatic switching mode.

SW-E1 No. 5 CNG detect time at TEL/FAX mode

The switch which sets the time from the start of CNG detection to the end of detection.

SW-E1 No. 6 Post answer tone (TEL/FAX mode)

When set to "0", machine send the tones in TEL/FAX auto changeover mode.

SW-E1 No. 7 Type of post answer tone

When set to "0", post answer tone is 800Hz single tone. When set to "1", post answer tone is 880Hz/988Hz/1046Hz(LA-SI-DO) tone.

SW-E1 No. 8 Pseudo ringer ON/OFF cycle

When set to "0", pseudo ringer is 1 sec ON and 2 sec OFF cycles. When set to "1", pseudo ringer is 1 sec ON and 4 sec OFF cycles.

SW-E2 No. 1 ~ No. 4 Pseudo ringer sound output level to the line (0~-15dBm setting by 1dBm step)

Used to adjust the sound volume of pseudo ringer to the line (ring back tone) generated on selecting TEL/FAX.

SW-E2 No. 5 ~ No. 8 Post answer tone transmission level (0~-15dBm setting by 1dBm step)

Used to adjust the sound volume of post answer tone to the line generated on selecting TEL/FAX.

SW-E3 No. 1 Reserved

Set to "0"

SW-E3 No. 2, No. 3 Action select when DTMF "#" is received during phone/fax automatic switching mode

SW-E3 No. 4 ~ No. 8 Reserved

Set to "0".

SW-F1 No. 1, No. 2 DTMF detection time

Used to set detect time of DTMF (Dual Tone Multi Frequency) used in remote reception(5 ). The longer the detect time is, the less the error detection is caused by noises.

SW-F1 No. 3 Protection of remote reception (5 ) detection

Used to set the function of remote reception (5 ). When set to "1", the remote reception function is disabled.

SW-F1 No. 4 Remote reception with GE telephone

"1": Compatible with TEL mode by GE "0": Not compatible

• When sending (5 ) for remote reception with a GE manufactured telephone remote reception may not take place because of special specifications in their DTMF.

To overcome this, a soft SW is provided to change the modem setting

to allow for remote reception.

• If this soft SW is set to "1", other telephone sets may be adversely affected.

SW-F1 No. 5 ~ No. 8 Remote operation code figure by external TEL (0~9)

Remote operation codes can be changed from 0 through 9. If set to greater than 9, it defaults to 9. The "5 " is not changed. Ex- 7 (Default : 5 )

SW-F2 No. 1 CNG detection in STAND-BY mode

When setting to "1", the CNG signal detection function during standby stops.

SW-F2 No. 2, No. 3 Number of CNG detect (AM mode)

Used for detection of CNG in 1 to 4 pulses.

SW-F2 No. 4, No. 5 Number of CNG detect (STAND-BY mode)

Used for detection of CNG in 1 to 4 pulses.

SW-F2 No. 6 ~ No. 8 Reserved

Set to "0"

SW-G1 No. 1 ~ No. 8 Reserved

Set to "0"

SW-G2 No. 1 ~ No. 8 Reserved

Set to "0"

SW-G3 No. 1 ~ No. 8 Reserved

Set to "0"

SW-G4 No. 1 ~ No. 6 Quiet detect level setting (0~-44dBm setting by 1dBm step)

This is used to change the quiet detect level setting. If quiet detection is difficult due to noise, reduce this setting level. (Example) Factory setting : 1 0 1 1 0 0 (- 44dBm)

↓ 1 0 1 0 0 0 (- 40dBm)

SW-G4 No. 7 Fax switching when A.M. full

If the answering machine’s memory (tape) is full and there is no response, the machine automatically switches to Fax reception.

SW-G4 No. 8 Reserved

Set to "0".

SW-H1 No. 1 Busy tone continuous sound detect time

Set detecting time busy tone for 5 seconds or 10 seconds.

UX-68DE FO-78DE

2 – 17

SW-H1 No. 2 Busy tone detect continuation sound detect during OGM

Used to detect the continuous tone of specific frequency during OGM output.

SW-H1 No. 3 Busy tone detect continuation sound detect

Used to select detection of the continuous sound of certain frequency.

SW-H1 No. 4 Busy tone detect intermittent sound detect during OGM

Used to detect the intermittent tone of specific frequency during OGM output.

SW-H1 No. 5 Busy tone detect intermittent sound detect

Used to select detection of the intermittent sound of certain frequency.

SW-H1 No. 6, No. 7 Busy tone detection pulse number

Used to set detection of Busy tone intermittent sounds.

SW-H1 No. 8 Reserved

Set to "0".

SW-H2 No. 1 ~ No. 8 Reserved

Set to "0".

SW-I1 No. 1, No. 2 ICM recording time

Used to select the incoming message recording time among 15sec/30sec/ 60sec/4min.

SW-I1 No. 3, No. 4 A.M. quiet time 1

Used to select four kinds of no sound time (2 sec ~ 5 sec) after reception in the T.A.D mode until OGM is output.

Reception

OGM output ICM recording

2 sec~ 5 sec ( SW-I1No. 3, No. 4)

Reception

OGM output ICM recording

0 sec~3 sec (SW-I1 No. 5, No. 6)

SW-I1 No. 5, No. 6 A.M. quiet time 2

Used to select four kinds of no sound time (0 sec ~ 3 sec) after OGM output the T.A.D mode until ICM recording is started.

SW-I1 No. 7 key input buzzer on/off switch (Two way recording mode)

Used to turn ON/OFF key input buzzer in the TWO-WA Y recording mode.

SW-I1 No. 8 Reserved

Set to "0".

SW-I2 No. 1 ~ No. 5 A.M. quiet detect time

Used to set no sound time (0 sec - 32 sec) during the T.A.D. mode operation.

SW-I2 No. 6 ~ No. 8 Reserved

Set to "0".

SW-I3 No. 1 Two way alarm

When set to "1", alarm sound is given to remote side during two way recording.

SW-I3 No. 2 Max OGM record time

Used to select the maximum OGM recording time (1=15sec, 0=60sec).

SW-I3 No. 3 Two way record function

If this switch is set to "1", machine doesn’t work two way recording function.

SW-I3 No. 4 Toll saver

Used to turn on the toll saver function. If it is off, the reception frequency in the AM mode is indentical with that in the FAX mode.

SW-I3 No. 5 FAX reception in case of detecting no sound detect after ICM recording

If this switch is set to "0", machine doesn’t change to FAX reception mode when detect no sound in ICM recording.

SW-I3 No. 6, No. 7 Reserved

Set to "0".

SW-I3 No. 8 Transfer dial recall

If this switch is set to "1", machine disable redial in Transfer function.

SW-I4 No. 1 ~ No. 4 AGC maximum gain (Line) (10~25dB) (1 dB step)

The AGC Maximum Gain limits the gain applied by the AGC. Message with average energy below the AGC Energy Reference Level will have their average energy level increased by no more than the AGC Maximum Gain. The AGC Maximum Gain should average energy of the message with the lowest average energy to the AGC Energy Reference Level.

SW-I4 No. 5 ~ No. 8 AGC maximum gain (Mic) (10~25dB) (1 dB step)

SW-I5 No. 1 ~ No. 4 AGC eref access code (Line) (-0~-30dB) (2 dB step)

The AGC Energy Reference Level controls the playback level. Any message having average speech energy above the energy reference level has its playback level attenuated, and any level has its playback level increased. If the playback level is too high (low), then decreasing (increasing) the AGC energy Reference level will achieve the desired level.

SW-I5 No. 5 ~ No. 8 AGC eref access code (Mic) (-0~-30dB) (2 dB step)

SW-I6 No. 1 ~ No. 4 AGC gain adaptation threshold (Line)

The AGC adjusts the amount of gain applied to the incoming message only when the average energy exceeds the AGC Gain Adaptation Threshold. The AGC Gain Adaptation Threshold prevents message background noise from corrupting the gain provided that the AGC Gain Adaptation Threshold is greater than the background noise energy. In the event that a message has background noise energy greater than the AGC Gain Adaptation Threshold, the AGC Gain can be no greater than the AGC Maximum Gain. Note that the AGC Gain Adaptation Threshold must always be greater than the RPACS VOX Turn-On Threshold.

SW-I6 No. 5 ~ No. 8 AGC gain adaptation threshold (Mic)

SW-I7 No. 1, No. 2 AGC slew rate (Line)

The AGC Slew Rate controls the convergence of the message playback level to the desired playback level. A large slew rate will allow faster convergence and a small slew rate will allow slower convergence.

SW-I7 No. 3, No. 4 AGC slew rate (Mic)

UX-68DE FO-78DE

2 – 18

SW-I7 No. 5 ~ No. 8 Reserved

Set to "0".

SW-I8 No. 1 ~ No. 5 OGM/ICM output level (0~-31dBm setting by 1dBm step)

Used to control OGM and ICM output level.

SW-I8 No. 6 AM OGM announce only mode

If this switch is set to 1, the machine is not recording ICM. (disconnect the line after OGM output)

SW-I8 No. 7, No. 8 Reserved

Set to "0".

SW-J1 No. 1 Sender's phone number setting

Used to make a choice of whether the registered sender's phone number can be changed or not. If the switch is set to "1", new registration of the sender's phone number is disabled to prevent accidental wrong input.

SW-J1 No. 2 Summer time setting

Used to set YES/NO of automatic clock adjustment for Summer time.

SW-J1 No. 3, No. 4 Ringer Volume

Used to adjust ringing volume.

SW-J1 No. 5, No. 6 Reserved

Set to "0".

SW-J1 No. 7 Polling key

If this switch is set to 1, the last of Rapid key works as polling key.

SW-J1 No. 8 Reserved

Set to "0".

SW-J2 No. 1, No. 2 Reserved

Set to "0".

SW-J2 No. 3 ~ No. 5 Speaker Volume

Used to adjust sound volume from a speaker.

SW-J2 No. 6 Speaker monitor function

Used to select whether to make the speaker monitor function valid or not.

SW-J2 No. 7 Saving energy start timing

Used to set the time between the machine’s stand-by state (clock indication) after operation and saving energy mode. It is possible to set the time to either 5 sec or 180 sec (default).

SW-J2 No. 8 Saving energy mode

Used to select whether to make the saving energy mode valid or not.

SW-J3 No. 1 ~ No. 3 Communication results printout (Transaction report)

It is possible to obtain transaction results after each communication. Normally,the switch is set (No. 1 : 0, No. 2 : 0, No. 3 : 0) so that the transaction report is produced only when a communication error is encountered. If No.1 was set to 0 and No. 2 to 1 and No. 3 to 0, the transaction report will be produced every time a communicaion is done, even if the communicaion was successful. Setting No. 1 to 0 and No. 2 to 1 and No. 3 to 1 will disable this function. No transaction report printed.

SW-J3 No. 4 Time format

When set to "0", 24hour time format is used. When set to "1", 12hour time format is used.

SW-J3 No. 5 Date format

When set to "0", Day-Month-Y ear format is used. When set to "1", Month-Day-Y ear format is used.

SW-J3 No. 6 ~ No. 8 Reserved

Set to "0".

SW-K1 No. 1 Entering diag mode by pressing SPEED key

A bit which is used in the production process only . When the SPEED key is pressed, the switch is changed from the stand-by state to the diag mode.

SW-K1 No. 2 ~ No. 8 Reserved

Set to "0".

UX-68DE FO-78DE

2 – 19

[3] Troubleshooting

Refer to the following actions to troubleshoot any of the problems mentioned in 1-4.

[1] A communication error occurs. [2] Image distortion produced. [3] Unable to do overseas communication. [4] Communication speed slow due to FALLBACK.

• Increase the transmission level SOFT SWITCH A4-1, 2, 3, 4, 5.

May be used in case [1] [2] [3].

• Decrease the transmission level SOFT SWITCH A4-1, 2, 3, 4,

5. May be used in case [3].

• Apply line equalization SOFT SWITCH A5-1, 2.

May be used in case [1] [2] [3] [4].

• Slow down the transmission speed SOFT SWITCH A2-1, 2, 3,

4. May be used in case [2] [3].

• Replace the TEL/LIU PWB.

May be used in all cases.

• Replace the control PWB.

May be used in all cases.

* If transmission problems still exist on the machine, use the following

format and check the related matters.

TO: ATT: Ref.No. : CC: ATT: Date : FM: Dept :

Sign :

* Please complete this report before calling the “TAC” hotline if problem still occurs.

***** Facsimile communication problem *****

Ref.No.: Date:

From: Mr. Fax T el No.: Our customer Name T el No.

Address Fax No. Contact person Model name

Other party Name Tel No.

Address Fax No. Contact person Model name

Problem mode Line: Domestic / international Model: G3 Phase: A, B, C, D.

Reception / Transmission

Automatic reception / Manual reception

Automatic dialing / Manual dialing / Others Frequency: % ROM version: Confirmation

item

Please mark problem with an X. No problem is: 0.

A1 A2 B1 B2 C1 C2 D1 D2 E1 E2

Transmission level setting is ( ) dB at our customer Transmission level ( ) dBm Reception level ( ) dBm By level meter at B1 and B2

Comment

**** Please attach the G3 data and activity report on problem. ****

Countermeasure

Our customer

Our service

A1 A2

C1 D2

B1 B2

E1 E2

C2 D1

Other party

Other part

's service

UX-68DE FO-78DE

[4] Error code table

1. Communication error code table G3 Transmission

Code Final received signal Error Condition (Receiver side)

0 Incomplete signal frame Cannot recognize bit stream after flag

1 NSF, DIS Cannot recognize DCS signal by echo etc.

Cannot recognize NSS signal (FIF code etc)

2 CFR Disconnects line during reception (carrier missing etc) 3 FTT Disconnects line by fall back

4 MCF Disconnects line during reception of multi page

Cannot recognize NSS, DCS signal in the case of mode change

5 PIP or PIN The line is hung up without replying to telephone request from the receiving party.

6 RTN or RTP Cannot recognize NSS, DCS signal after transmit RTN or RTP signal. 7 No signal or DCN No response in receiver side or DCN signal received* (transmitter side)

8 − Owing to error in some page the error could not be corrected although the specified number of

error retransmissions were attempted.

11 − Error occurred after or while reception by the remote (receiving) machine was revealed to be

impossible. 12 − Error occurred just after fallback. 13 − Error occurred after a response to retransmission end command was received.

G3 Reception

Code Final received signal Error Condition (Receiver side)

0 Incomplete signal frame Cannot recognize bit stream after flag

1 NSS, DCS Cannot recognize CFR or FTT signal

Disconnects line during transmission (line error)

2 NSC, DTC Cannot recognize NSS signal (FIF code etc) 3 EOP Cannot recognize MCF, PIP, PIN, RTN, RTP signal 4 EOM Cannot recognize MCF, PIP, PIN, RTN, RTP signal in the case of mode change

5 MPS The line is hung up without replying to communication request. 6 PR1-Q Cannot recognize PIP, PIN signal in the case of TALK request

7 No signal or DCN No response in transmitter (cannot recognize DIS signal) or DCN signal received* (receiver side) 8 − Error occurred upon completion of reception of all pages.

9 − Error occurred when mode was changed or T ransmission/Reception switching was performed.

10 − Error occurred during partial page or physical page reception. 11 − Error occurred after or during inquiry from the remote (transmitting) machine as to whether

reception is possible or not. 12 − Error occurred during or just after fallback.

13 − Error occurred after the retransmission end command was received.

2 – 20

UX-68DE FO-78DE

2 – 21

M E M O

UX-68DE FO-78DE

4 – 1

[1] Block diagram

CHAPTER 4. DIAGRAMS

SRAM

256kbit

ROM

2Mbit

CPU

CPU I/F

TIMER

RTC

PIO

WATCHDOG

TIMER

CLOCK

32.768kHz

INTERRUPT

CONTROLLER

CIS I/F

MOTOR I/F

SENSOR I/F

SIO

THERMAL

HEAD I/F

PANEL I/F

OPERATION

PANEL

CONTROL PWB UNIT

1CHIP FAX ENGINE (FC200)

HANDSET

SPEAKER

+5V +24V

OPERATION

PANEL

TEL/LIU

PWB UNIT

DRIVER

THERMAL

HEAD

CONTACT

IMAGE

SENSOR

POWER SUPPLY

PWB UNIT

STABILIZER

MODEM

FM209V

AMPLIFIER

SURGE

PROTECT/

FILTER

CML TRANSFORMER

VBT

RECTIFIER

TRANSFORMER

RECTIFIER

DIODE

TRANS

SURGE

ABSORBER

FILTER

LINE

PAPER

SENSOR

RESET IC

AMPLIFIER

CLOCK

32.256MHz

LCD

D-FF

16MHz

+3.3V

+5V

REGULATOR

AMPLIFIER

FLASH

MEMORY

512k x 8bit

SPEAKER

AMPLIFIER

UX-68DE FO-78DE

[2] Wiring diagram

4 – 2

CNCIS

CNDR

CNTH

DOOR

SENSOR

CNPW

CN2

CNLIUA

CNLNJ

CNLIUA

CNFRS

FRONT

SENSOR

CNSP

CNCSWCNMT

CAM SW

TX/RX

MOTOR

CNPN

SPEAKER

CNPN

CNLCD

OPERATION

PANEL PWB

UNIT

LCD UNIT

THERMAL HEAD

CIS(CONTACT IMAGE SENSOR)UNIT

HANDSET

ARG

CNHJ

TEL/LIU

PWB UNIT

POWER SUPPLY

PWB UNIT

CONTROL

PWB UNIT

AC CORD

CNTLJ

CNLIUB CNLIUB

UX-68DE FO-78DE

[3] Point- to-point diagram

4 – 3

TX/RX

MOTOR

TPAD TPBD TPAD TPBD

VMT VMT

1 2 3 4 5 6

1 2 3 4 5 6 7 8

9 10 11 12 13 14 15 16

1 2 3 4 5 6 7 8

9 10 11 12 13 14 15 16

1 2 3 4 5 6 7 8

9 10 11 12 13 14 15 16

1 2 3 4 5 6 7 8

9 10 11 12 13 14 15 16

1 2 3 4 5 6

OPERATION

PANEL

PWB

TPAD TPBD TPAD TPBD

VMT VMT

THERMAL

HEAD

VTH

VTH STRB1 STRB2

THI

N.C.

MG MG MG

+5V STRB3 STRB4 LATCH

PCLK DATA

VTH

VTH STRB1 STRB2

THI

RANK

MG MG MG

+5V STRB3 STRB4 LATCH

PCLK DATA

VTH

1 2 3 4 5 6 7

VO DG

+5V

øT

CISCLK

GLED

+24V

VO DG

+5V

øT

CISCLK

GLED

+24V

+5V

SEN4

E SEN0 SEN1 SEN2 SEN3 SEN5 SEN6 SEN7

ORGSNS

KEN4A KEN3A KEN2A KEN1A

+5V

SEN4

E SEN0 SEN1 SEN2 SEN3 SEN5 SEN6 SEN7

ORGSNS

KEN4A KEN3A KEN2A KEN1A

CNPN CNPN

CNCIS

1 2 3 4 5 6 7 8

9 10 11 12

1 2 3 4 5 6 7 8

9 10 11 12

TEL/LIU

PWB

TELOUT

TELIN

TELMUTE

RHS

RXIN

TXOUT

CML

+5V

+24V

TELOUT

TELIN

TELMUTE

RHS

RXIN

TXOUT

CML

+5V

+24V

CNLIUACNLIUA

CNMT

CNTH

1 2 3 4 5 6 7 8

POWER

SUPPLY

PWB

+5V

MG +24V +24V

PSAVE

+5V

MG +24V +24V

PSAVE

CN2

CNPW

CNCSW

CNSP

CIS

1 2

CSW

CAM

SWITCH

1 2

SP+ SP-

CSW

SP+

SP-

SPEAKER

CONTROL

PWB

CNFRS

1 2

FRSNS

FRONT

SENSOR

CNDR

1 2

DRSNS

DOOR

SENSOR

1 2 3 4 5

RLYCNT

N.C.

DPON

DPMUTE

E-RLY

RLYCNT TXMUTE

DPON

DPMUTE

E-RLY

CNLIUBCNLIUB

UX-68DE FO-78DE

CHAPTER 5. CIRCUIT DESCRIPTION

[1] Circuit description

1. General description

The compact design of the control PWB is obtained by using CONEXANT fax engine in the main control section and high density printing of surface mounting parts. Each PWB is independent according to its function as shown in Fig. 1.

2. PWB configuration

Fig. 1

1) Control PWB

The control PWB controls peripheral PWBs, mechanical parts, transmission, and performs overall control of the unit. This machine employs a 1 chip modem (FM209V) which is installed on the control PWB.

2) TEL/LIU PWB

This PWB controls connection of the telephone line to the unit.

3) Power supply PWB

This PWB provides voltages of +5V and +24V to the other PWBs.

4) Panel PWB

The panel PWB allows input of the operation keys.

5) LCD PWB

This PWB controls the LCD display.

3. Operational description

Operational descriptions are given below:

• Transmission operation

When a document is loaded in standby mode, the state of the document sensor is sensed via the 1 chip fax engine (FC200). If the sensor signal was on, the motor is started to bring the document into the standby position. With depression of the START key in the off-hook state, transmission takes place. Then, the procedure is sent out from the modem and the motor is rotated to move the document down to the scan line. In the scan processor, the signal scanned by the CIS is sent to the internal image processor and the AD converter to convert the analog signal into binary data. This binary data is transferred from the scan processor to the image buffer within the RAM and encoded and stored in the transmit buffer of the RAM. The data is then converted from parallel to serial form by the modem where the serial data is modulated and sent onto the line.

• Receive operation

There are two ways of starting reception, manual and automatic. Depression of the START key in the off-hook mode in the case of manual receive mode, or CI signal detection by the LIU in the automatic receive mode.

First, the FC200 controls the procedure signals from the modem to be ready to receive data. When the program goes into phase C, the serial data from the modem is converted to parallel form in the modem interface of the 1 chip fax engine (FC200) which is stored in the receive buffer of the RAM. The data in the receive buffer is decoded software-wise to reproduce it as binary image data in the image buffer. The data is DMA transferred to the recording processor within the FC200 which is then converted from parallel to serial form to be sent to the thermal head. The data is printed line by line by the FC200 which is assigned to control the motor rotation and strobe signal.

• Copy operation

T o make a copy on this facsimile, the COPY key is pressed when the machine is in stand-by with a document on the document table and the telephone set is in the on-hook state.

First, depression of the COPY key advances the document to the scan line. Similar to the transmitting operation, the image signal from the CIS is converted to a binary signal in the DMA mode via the 1 chip fax engine (FC200) which is then sent to the image buffer of the RAM. Next, the data is transferred to the recording processor in the DMA mode to send the image data to the thermal head which is printed line by line. The copying takes place as the operation is repeated.

5 – 1

LCD PWB

PANEL PWB

CONTROL PWB

TEL/LIU PWB

POWER SUPPLY PWB

TX/RX

MOTOR

AC CORD

CIS

UX-68DE FO-78DE

[2] Circuit description of control PWB

1. General description

Fig. 2 shows the functional blocks of the control PWB, which is composed of 5 blocks.

Fig. 2 Control PWB functional block diagram

2. Description of each block (1) Main control block

The main control block is composed of CONEXANT 1 chip fax engine (FC200), ROM (2Mbit), SRAM (256kbit), FLASH MEMORY (512k × 8 bit) and Modem (FM209V). Devices are connected to the bus to control the whole unit.

1) FC200 (IC3) : pin-144 QFP (FAX ENGINE)

2) FM209V (IC5) : pin-128 QFP (MODEM)

The FAX ENGINE Integrated Facsimile Controllers. FC200, contains an internal 8 bit microprocessor with an external 16

Mbyte address space and dedicated circuitry optimized for facsimile image processing and facsimile machine control and monitoring.

3) 27C2000 (IC10): pin-32 DIP (ROM)

ROM of 2 Mbit equipped with software for the main CPU.

4) W24258S-70LE (IC6): pin-28 SOP (SRAM)

Line memory for the main CPU system RAM area and coding/decoding process. Used as the transmission buffer.

Memory of recorded data such as daily report and auto dials. When the power is turned off, this memory is backed up by the lithium battery.

5) KM29W040T (IC4): pin-44 TSOP (FLASH MEMORY)

A 512k × 8 bit NAND FLASH MEMORY to store the voice and image data when using memory functions.

Fig. 3

5 – 2

(1) FAX ENGINE

(3) ROM

(2) MODEM

(4) SRAM

MAIN CONTROL BLOCK

MODEM BLOCK

(5) FLASH MEMORY

MC24 CPU CONTROL IF

MC24 MEGACELL(8BIT DATA,24BIT ADDRESS)

WATCHDOG TIMER

REAL TIME CLOCK

CRYSTAL OSCILLATOR

BATTERY BACK-UP CIRCUIT

INTERRUPT CONTROLLER

BUS INTERFACE DRAM CONTROL

INTERNAL & EXTERNAL BUS CONTROL

INTERNAL & EXTERNAL DECODE

DMA CONTROLLER

OPERATOR PANEL IF

32 KEYS

8 LEDS

LCD MODULE

MOTOR POWER

CONTROL RINGER

SYNC SERIF 1

THERMAL PRINTER IF

5 ms LINE TIME

A4/B4 LINES

TPH ADC

4 STROBE TPH

LATCHLESS TPH

EXTEMAL DMA I/F

T.4/T.6 CODEC

MH,MR,MMR

HARDWARE,ALTERNATE

COMPRESSION &

DECOMPRESSION

BI-LEVEL RESOLUTION

CONVERSION

PROGRAMMABLE

REDUCTION &

EXPANSION

2.6kBYTE VIDEO RAM

SCANNER CONTROL & VIDEO PROCESSING

8-BIT PADC

CCD/CIS SCANNER

5 ms,A4/B4 LINES

SHADING CORRECTION(1:1,1:8)

DITHERING

MULTILEVEL B4-A4 REDUCTION

ERROR DIFFUSION

MTF

GENERAL I/O

TONE/ALTTONE

GPIO

CALLING PARTY

CONTROL

AUTOBAUD

SYNC-ASYNC SASIF

SYNC SERIF 2

FLASH MEMORY IF

AUTOBAUD

CPU BUS

INTERNAL CPU BUS

EXTERNAL CPU BUS

DMA BUS

WRPROTN TSTCLK

DEBUGN RESETN XIN XOUT PWRDWNN BATRSTN

SYSCLK

SEE "OPIF OUTPUTS" BELOW

SEE "OPIF INPUTS" BELOW

THADIN PDAT

PLAT STRB[3:0] STRBPOL

PCLK

PWR/GND TEST

OPIF INPUTS OPI[0]/GPIO[21]/SSRXD1

OPI[1]/GPIO[22]/SSSTAT1 OPI[2]/GPIO[23]/SSCLK1 OPI[3]/GPIO[24]

OPIF OUTPUTS LEDCTL/GPO[16]

LCDCS/GPO[17] OPO[0]/GPO[8]/SINPWR CTRL OPO[1]/GPO[9]/PMPWR CTRL OPO[2]/GPO[10]/RINGER OPO[3]/GPO[11] OPO[4]/GPO[12]/SSTXD1 OPO[5]/GPO[13] OPO[6]/GPO[14] OPO[7]/GPO[15]

ROMCSN

MCSN

SYNC

REGDMA

WAITN

RASN

CASN[1:0]

DWRN

CSN[1:0]

WRN

RDN

D[7:0]

A[23:0]

MIRQN

TONE

VIN

CLK1

CLK1N

CLK2 VIDCTL0/FCS1N VIDCTL1/FCS2N

START

–VREF

+VREF

GPIO[0] GPIO[1]/SASTXD GPIO[2]/SASRXD GPIO[3]/SASCLK GPIO[4]/CPCIN GPIO[5]/SSCLK2 GPIO[6]/SSTXD2 GPIO[7]/SSRXD2 GPIO[8]/FWRN GPIO[9]/FRDN GPIO[10]/SSSTAT2 GPIO[11]/BE/SERINP GPIO[12]/CS2N GPIO[13]/CS3N GPIO[14]/CS4N GPIO[15]/CS5N GPIO[16]/IRQ8 GPIO[17]/IRQ5N GPIO[18]/IRQ9N GPIO[19]/RDY/SEROUT GPIO[20]/ALTTONE SM[3:0]/GPO[7:4] PM[3:0]/GPO[3:0]

UX-68DE FO-78DE

CPU Control Interface MIRQn 135 I HU − Modem interrupt, active low . (Hysteresis In, Internal Pullup.) SYSCLK 133 I H − System clock. (Hysteresis In.) TSTCLK 130 O − 123XT T est clock.

Bus Control Interface

A[23:0] [1:6][8:13] O TU 123XT Address bus (24-bit).

[15:20][22:27]

D[7:0] [136:139] I/O TU 123XT Data bus (8-bit).

[141:144]

RDn 128 O − 123XT Read strobe. WRn 127 O − 123XT Write strobe. ROMCSn 120 O − 123XT ROM chip select. CS1n 122 O − 123XT I/O chip select. CS0n 57 O − 123XT SRAM chip select. (Battery powered.) MCSn 121 O − 123XT Modem chip select. SYNC 126 O − 123XT Indicates CPU op code fetch cycle (active high). REGDMA 124 O − 123XT Indicates REGSEL cycle and DMA cycle. WAITn 125 O − 123XT Indicates current TSTCLK cycle is a wait state or a halt state. RASn 113 O − 123XT DRAM row address select. (Battery powered.) CAS[1:0]n [111:112] O − 123XT DRAM column address select. (Battery powered.) DWRn 109 O − 123XT DRAM write. (Battery powered.)

Prime Power Reset Logic and Test DEBUGn 129 I HU − External non-maskable input (NMI). RESETn 131 I/O HU 2XO FC200 Reset. TEST 58 I C − Sets Test mode (Battery powered).

Battery Power Control and Reset Logic XIN 59 I OSC − Crystal oscillator input pin. XOUT 60 O − OSC Crystal oscillator output pin. PWRDWNn 62 I H −

Used by external system to indicate -to FC200 - loss of prime power.

(Results in NMI) BATRSTn 61 I H − Battery power reset input. WRPROTn 110 O − 1XC

(Battery powered.) Write protect during loss of VDD power.

NOTE:The functional logic is powered by battery power, but the output drive

is powered by DRAM battery power.

Scanner Interface START 101 O − 2XS Scanner shift gate control. CLK1 100 O − 2XS Scanner clock. CLK1n 99 O − 2XS Scanner clock-inverted. CLK2 98 O − 2XS Scanner reset gate control (or clock for CIS scanner). FCS1n/VIDCTL0 96 O − 2XT Flash memory chip select or Video Control signal. FCS2n/VIDCTL1 97 O − 2XT Flash memory chip select or Video Control signal.

Printer Interface PCLK/DMAACK 29 O − 3XC Thermal Print Head (TPH) clock, or external DMAACK. PDAT 30 O − 2XP Serial printing data (to TPH). PLAT 31 O − 3XP TPH data latch. STRB[3:0] [33:36] O − 1XP Strobe signals for the TPH. STRBPOL/DMAREQ

37 I C − Sets strobe polarity, active high/low or external DMA request.

Operator Panel Interface OPO[0]/GPO[8]/ 47 O − 2XL Keyboard/LED strobe [0] or GPO[8] or Scan Motor Power Control SMPWRCTRL OPO[1]/GPO[9]/ 46 O − 2XL Keyboard/LED strobe [1] or GPO[9] or Print Motor Power Control PMPWRCTRL OPO[2]/GPO[10]/ 44 O − 2XCT Keyboard/LED strobe [2] or GPO[10] or RINGER RINGER OPO[3]/GPO[11] 43 O − 2XL Keyboard/LED strobe [3] or GPO[11] OPO[4]/GPO[12]/ 42 O − 2XL Keyboard/LED strobe [4] or GPO[12] or SSTXD1 (for SSIF1) SSTXD1 OPO[5]/GPO[13] 40 O − 2XL Keyboard/LED strobe [5] or GPO[13] OPO[6]/GPO[14] 39 O − 2XL Keyboard/LED strobe [6] or GPO[14] OPO[7]/GPO[15] 38 O − 2XL Keyboard/LED strobe [7] or GPO[15] OPI[0]/GPIO[21]/ 52 I/O HU 2XC (Pullup, Hysteresis In) Keyboard return [0] or GPIO[21] or SSRXD1 SSRXD1 (for SSIF1) OPI[1]/GPIO[22]/ 51 I/O HU 2XC (Pullup, Hysteresis In) Keyboard return [1] or GPIO[22] or SSSTAT1 SSSTAT1 (for SSIF1)

FC200 (IC3) Terminal descriptions

Pin Name Pin No. I/O

Input Output Pin Description Type Type (Note: Active low signals have an "n" pin name ending.)

5 – 3

UX-68DE FO-78DE

Operator Panel Interface OPI[2]/GPIO[23]/ 50 I/O HU 2XC (Pullup, Hysteresis In) Keyboard return [2] or GPIO[23] or SSCLK1 SSCLK1 (for SSIF1) OPI[3]/GPIO[24] 49 I/O HU 2XC (Pullup, Hysteresis In) Keyboard return [3] or GPIO[24] LEDCTL 55 O − 4XC Indicates outputs OPO[7:0] are for LEDs. LCDCS 54 O − 1XC LCD chip select.

General Purpose I/O GPIO[0] 94 I/O H 2XC (Hysteresis In) GPIO[0]. GPIO[1]/SASTXD 93 I/O H 2XC (Hysteresis In) GPIO[1] or SASTXD (for SERIF). GPIO[2]/SASRXD 92 I/O H 2XC (Hysteresis In) GPIO[2] or SASRXD (for SERIF). GPIO[3]/SASCLK 91 I/O H 2XC (Hysteresis In) GPIO[3] or SASCLK (for SERIF). GPIO[4]/CPCIN 90 I/O H 2XC (Hysteresis In) GPIO[4] or Calling Party Control Input. GPIO[5]/SSCLK2 89 I/O H 2XC (Hysteresis In) GPIO[5] or SSCLK2 (for SSIF2). GPIO[6]/SSTXD2 87 I/O H 2XC (Hysteresis In) GPIO[6] or SSTXD2 (for SSIF2). GPIO[7]/SSRXD2 86 I/O H 2XC (Hysteresis In) GPIO[7] or SSRXD2 (for SSIF2). GPIO[8]/FWRn 85 I/O H 2XC (Hysteresis In) GPIO[8] or flash write enable signal for NAND-type flash

memory.

GPIO[9]/FRDn 84 I/O H 2XC (Hysteresis In) GPIO[9] or flash read enable signal for NAND-type flash

memory.

GPIO[10]/SSSTAT2

83 I/O H 2XC (Hysteresis In) GPIO[10] or SSSTAT2 (for SSIF2). GPIO[11]/BE/ 82 I/O H 1XC (Hysteresis In) GPIO[11] or bus enable or serial port data input for SERINP autobaud detection. GPIO[12]/CS[2]n 80 I/O H 2XC (Hysteresis In) GPIO[12] or I/O chip select [2]. GPIO[13]/CS[3]n 79 I/O H 2XC (Hysteresis In) GPIO[13] or I/O chip select [3]. GPIO[14]/CS[4]n 78 I/O H 2XC (Hysteresis In) GPIO[14] or I/O chip select [4]. GPIO[15]/CS[5]n 77 I/O H 2XC (Hysteresis In) GPIO[15] or I/O chip select [5]. GPIO[16]/IRQ[8] 76 I/O H 1XC (Hysteresis In) GPIO[16] or external interrupt 8. GPIO[17] 75 I/O H 1XC (Hysteresis In) GPIO[17]. GPIO[18]/IRQ[9]n 74 I/O H 1XC (Hysteresis In) GPIO[18] or external interrupt 9. GPIO[19]/RDY/ 73 I/O H 1XC (Hysteresis In) GPIO[19] or ready signal or Serial port data output for SEROUT autobaud detection. GPIO[20]/ALTTONE

107 I/O H 1XC (Hysteresis In) GPIO[20] or ALTTONE.

Miscellaneous SM[3:0]/GPO[7:4] [103:106] O − 1XC Programmable: scan motor control pins or GPO pins. PM[3:0]/GPO[3:0] [115:118] O − 1XC Programmable: print motor control pins or GPO pins. TONE 119 O − 1XC Tone output signal.

Power, Reference Voltages, Ground

-Vref/CLREF 66 I -VR − Negative Reference Voltage for Video A/D or Reference Voltage for the

Clamp Circuit.

ADXG 68 I VXG − A/D Internal GND. (NOTE: This pin requires an external 0.22µF decoupling

capacitor to ADGA.) ADGA 69 VADG A/D Analog Ground ADVA 70 VADV A/D Analog Power ADGD 72 VADG A/D Digital Ground +Vref 71 I +VR Positive Reference Voltage for Video A/D. VIN 67 I VA − Analog Video A/D input. THAD1 65 I TA − Analog Thermal A/D input.

Power and Ground

VSS(12) 7,21,28,45, Digital Ground

53,56,64,88, 95,108,132, 134

VDD(8) 14,32,41,48, Digital Power

81,102,123,

140 VBAT 63 Battery Power VDRAM 114 DRAM Battery Power

FC200 (IC3) Terminal descriptions

Pin Name Pin No. I/O

Input Output

Pin Description

Type Type

5 – 4

UX-68DE FO-78DE

(2) Panel control block

The following controls are performed by the FC200.

• Operation panel key scanning

• Operation panel LCD display

(3) Mechanism/recording control block

• Recording control block diagram (1)

Fig. 4

5 – 5

OPERATOR

PANEL,

KEYPAD,

LEDS & LCD

PANEL/LCD PWB

PRINTER DATA

CONTROI &

SENSORS

THERMAL HEAD

OPO[7:0]* OPI[3:0]* LEDCTL* LCDCS*

TEST BATRSTN RESETN

STRB[3:0] STRBPOL THADI PDAT PCLK PLAT

TONE/ALTTONE TSTCLK REGDMA WAITN SYNC PWRDWNN

PRINTER &

SCANNER

MOTOR DRIVERS

MOTOR

PM[3:0]*

SM[3:0]*

RTC

CRYSTAL

SCANNER

CONTROLS &

SENSORS

START CLK2 CLK1 CLK1N VIDCTL[1:0]

XIN XOUT

MIRON MCSN

SYSCLK

D[7:0] RDN

A[4:0]

WRN

MONOFAX

FACSIMILE

MODEM

ANALOG SWITCH

LINE

INTERFACE

SPEAKER

MICROPHONE

CIRCUIT

TELEPHONE LINE

RXA

TXA

SPKR

MIC RIN

SPKRLO

SPKRHI

SPKR

RIN

TXA2

TXA1

TXOUT

RXIN

XIA

GPIO

DRAM

(OPTION)

SCANNER

VIDEO

PREPROCESSING

SYNC PORTS (2)

(SSIF)

VIN +VREF –VREF

SSCLK[2:1]* SSTXD[2:1]* SSRXD[2:1]* SSSTAT[2:1]*

SYNC/ASYNC

SERIAL

PORT

SASCLK SASTXD SASRXD

GPIOGENERAL

PURPOSE I/O

CIS

DEBUGN VDD VDRAM VBAT VSS

FLASH MEMORY

WRPROTN FRDN* FRWN* FCLE* FCS[0:2]

D[7:0] RDN

A[23:0]

WRN ROMSCN

CS[5:0]N*

TXDAT RMODE

RXDAT

TMODE CLKIN SLEEPN

GPIO

CAS[0,1]N,RASN,DWRN

NOTES:*ALTERNATIVE GPO,GPI OR GPIO LINES

SPEAKERPHONE ONLY

VOICE OR SPEAKERPHONE

EXTENDED FACSIMILE

CONTROLLER

EXTERNAL BUS

D[7:0]

UX-68DE FO-78DE

(4) Modem (FM209V) block

INTRODUCTION

The CONEXANT FM209V MONOFAX modem is a synchronous 9600 bits per second (bps) half-duplex modem with error detection and DTMF reception. It has low power consumption and requires a single +5V and +3.3V DC power supply. The modem is housed in a single VLSI device package. The modem can operate over the public switched telephone network (PSTN) through line terminations provided by a data access arrangement (DAA). The FM209V is designed for use in Group 3 facsimile machines. The modem satisfies the requirements specified in CCITT recommendations V.29, V.27 ter, V.21 Channel 2 and T.4, and meets the binary signaling requirements of T.30. The modem can operate at 9600, 7200, 4800, 2400, or 300 bps, and also includes the V.27 ter short training sequence option. The modem can also perform HDLC framing according to T.30 at 9600, 7200, 4800, 2400, or 300 bps. The modem features a programmable DTMF receiver and three programmable tone detectors which operate concurrently with the V.21 channel 2 receiver. The voice mode allows the host computer to efficiently transmit and receive audio signals and messages. The modem is available in either a 128-pin plastic quad flat pack (TQFP). General purpose input/output (GPIO) pins are available for host as signment in the 128-pin TQFP. The modem’s small size, single voltage supply, and low power consumption allow the design of compact system enclosures for use in both office and home environments. MONOFAX is a registered trademark of CONEXANT.

FEATURES

• Group 3 facsimile transmission/reception

- ITU-T V.29, V.27 ter, T.30, V.21 Channel 2, T .4

- ITU-T V.17 and V.27 ter short train

- HDLC framing at all speeds

- Receive dynamic range: 0 dBm to -43 dBm

- Automatic adaptive equalization

- Fixed and programmable digital compromise equalization

- DTMF detect and tone detect

- ITU-T V.21 Channel 2 FSK 7E Flag Detect

- Ring detector

- Programmable transmits level

- Programmable single/dual tone transmission

• V.23 and T ype I Caller ID

- Full-duplex modes: TX = 75 bps. RX = 1200 bps TX = 1200 bps. RX = 75 bps

- Half-duplex mode: TX = RX = 1200 bps

- Serial and parallel data modes

- Programmable parallel data mode

- 5, 6, 7 or 8 data bits

- 1 or 2 Stop bits

- Mark, Space, Even, or Odd Parity

- Break function

- Transmitter squelch

- Compromise equalizer

• Programmable interface memory interrupt

• Eight General Purpose Input (GPI) and eight General Purpose Out-

put (GPO) pins for host assignment

• DTE interface: two alternate ports

- Selectable microprocessor bus (6500 or 8085)

- ITU-T V.24 (EIA/TIA-232-E compatible) interface

• TTL and CMOS compatible

• 3.3V/5V operation

• Power consumption

- Operating Mode: 200 mW (Basic), 275 mW (-V option). 300 mW (-VS option)

- Sleep Mode: 1 ma (Basic. -V option and -VS option)

• Packaging

- 128-pin TQFP (thin quad flat pack)

5 – 6

Fig. 5

USART

(OPTIONAL)

HOST

PROCESSOR

(DTE)

DECODER

CRYSTAL

DAA

SPEAKER

DRIVER

(OPTIONAL)

EYE

PATTERN

GENERATOR

(OPTIONAL)

POWER SUPPLY

FM209V

MONOFAX

MODEM

TXD RXD DCLK RTS# CTS# RLSD#

READ# WRITE# DATA BUS ADDR BUS

CS#

RESET#

IRQ1# IRQ2#

XTLI XTLO

EYECLK EYESYNC

EYEXY

SPKRM

SPKRP

LINEIN

LINEOUT

RINGD

TALK

OFFHOOK

TELEPHONE

LINE

GND

+3.3V

+5V

UX-68DE FO-78DE

5 – 7

FM209V (IC5) Hardware Interface Signals

Pin Signals – 128-Pin TQFP

Pin No. Signal Name I/O Type Pin Description

1 SR4IN/RESERVED MI Modem Interconnect 2 SR3OUT/RESERVED MI Modem Interconnect 3 EYESYNC OA Eye Pattern Circuit 4 EYECLK OA Eye Pattern Circuit 5 RXD OA DTE serial interface 6 SR1IO MI Modem Interconnect 7 NC — No Connection 8 EYEXY OA Eye Pattern Circuit

9 SR4OUT MI Modem Interconnect 10 VDD1 PWR 3.3V Digital Supply for DSP 11 RLSD# OB DTE Serial Interface 12 DCLK OB DTE Serial Interface 13 EN85# IA Host Parallel Interface 14 GPI0 IA Host Parallel Interface 15 RTS# IA DTE Serial Interface 16 DGND1 GND DSP Digital Ground 17 TXD IA DTE Serial Interface 18 SA1CLK MI Modem Interconnect 19 RS4 IB Host Parallel Interface 20 RS3 IB Host Parallel Interface 21 RS2 IB Host Parallel Interface 22 RS1 IB Host Parallel Interface 23 RS0 IB Host Parallel Interface 24 YCLK I Modem Interconnect 25 IACLK MI Modem Interconnect 26 IA1CLK MI Modem Interconnect 27 CTRLSIN S/NC MI Modem Interconnect 28 RESERVED/NC MI Modem Interconnect 29 SOUT S/NC MI Modem Interconnect 30 SIN S/NC MI Modem Interconnect 31 FSYNC S/NC MI Modem Interconnect 32 IARESET S#/NC MI Modem Interconnect 33 AGND1 GND IA Analog Ground 34 LINEIN S/NC I Line Interface 35 MICP S/NC I Microphone Input 36 MICM S/NC I Microphone Input 37 MICBIAS S/NC O Microphone Bias Output 38 NC — No Connection 39 NC — No Connection 40 VREF S/NC MI Modem Interconnect 41 VC S/NC MI Modem Interconnect 42 VAA S/NC PWR 5V IA Analog power 43 LINEOUT S/NC O Line Interface 44 NC — No Connection 45 AGND2 GND IA Analog Ground 46 SPKRP S/NC O Speaker Interface Output 47 SPKRM S/NC O Speaker Interface Output 48 AVDD S/NC PWR 5V IA Digital power 49 RESERVED/NC MI Modem Interconnect 50 ICLK S/NC MI Modem Interconnect 51 MCLK P MI Modem Interconnect 52 CTRLSIN P MI Modem Interconnect 53 RESERVED MI Modem Interconnect 54 SOUT P MI Modem Interconnect 55 SIN P MI Modem Interconnect 56 FSYNC P MI Modem Interconnect 57 IARESET P# MI Modem Interconnect 58 AGND3 GND IA Analog Ground 59 NC — No Connection 60 LINEIN P I Line Interface 61 MICP P I Microphone Input 62 MICM P I Microphone Input 63 MICBIAS P O Microphone Bias Output 64 NC — No Connection 65 NC NC No Connection 66 VREF P MI Modem Interconnect 67 VC P MI Modem Interconnect 68 VAA P PWR 5V Analog Supply for IA 69 LINEOUT P O Line Interface 70 AGND4 GND IA Analog Ground 71 SPKRP P O Speaker Interface Output

UX-68DE FO-78DE

5 – 8

FM209V (IC5) Hardware Interface Signals

Pin Signals – 128-Pin TQFP

Pin No. Signal Name I/O Type Pin Description

72 SPKRM P O Speaker Interface Output 73 AVDD P PWR 5V Digital power for IA 74 NC — No Connection 75 ICLK P MI Modem Interconnect 76 MCLK S/NC MI Modem Interconnect 77 VDD2 PWR 3.3V Digital Supply for DSP 78 D7 IB/OC Host Parallel Interface 79 D6 IB/OC Host Parallel Interface 80 D5 IB/OC Host Parallel Interface 81 D4 IB/OC Host Parallel Interface 82 D3 IB/OC Host Parallel Interface 83 D2 IB/OC Host Parallel Interface 84 DGND2 GND DSP Digital Ground 85 VDD3 PWR 3.3V Digital Supply for DSP 86 D1 IB/OC Host Parallel Interface 87 DGND3 GND DSP Digital Ground 88 D0 IB/OC Host Parallel Interface 89 CSBR# IB Host Parallel Interface 90 WRITE# IB Host Parallel Interface 91 CS# IB Host Parallel Interface 92 READ# IB Host Parallel Interface 93 GPI2 IA General purpose input 94 GPI3 IA General purpose input 95 GPI4 IA General purpose input 96 GPI5 IA General purpose input 97 GPI6 IA General purpose input 98 GPI7 IA General purpose input

99 GPO7 OC General purpose output 100 VDD4 PWR 3.3V DSP Digital Power 101 GPO6 OC General purpose output 102 GPO5 OC General purpose output 103 RESERVED MI Modem Interconnect 104 GPO4 OC General purpose output 105 GPO3 OC General purpose output 106 DGND4 GND DSP Digital Ground 107 CTS# OB DTE Serial Interface 108 IRQ1# OB Interrupt request 109 GPO2 OC General purpose output 110 GPO1 OC General purpose output 111 GPO0 OC GPO0 (IA reset) 112 VDD5 PWR 3.3V DSP Digital Power 113 VGG PWR 5V DSP Digital 114 DGND5 GND DSP Digital Ground 115 RESET# IB External reset 116 XTALI I Crystal in 117 XTALO O Crystal out 118 RESERVED MI Modem Interconnect 119 XCLK OB X clock output 120 GPI1 IA General purpose input 121 IRQ2# OA Interrupt request 122 SR3IN MI Modem Interconnect 123 RESERVED MI Modem Interconnect 124 RESERVED MI Modem Interconnect 125 DGND6 GND DSP Digital Ground 126 DVAA PWR 3.3V DSP analog power 127 AGND5 GND DSP Analog Ground 128 RESERVED MI Modem Interconnect

Notes:

I/O types: MI = Modem interconnect.

IA, IB, = digital input OA, OB, OC = digital output I = analog input O = analog output

P Signals: Primary IA S Signals: Secondary IA Reserved = No external connection allowed.

UX-68DE FO-78DE

[3] Circuit description of TEL/LIU PWB

(1) TEL/LIU block operational description

1) Block diagram

2) Circuit description

The TEL/LIU PWB is composed of the following 6 blocks.

1. Speech circuit section

2. Dial transmission section

3. Speaker amplifier section

4. Ringer circuit section

5. Externally connected TEL OFF HOOK detection circuit

6. CI detection circuit

Fig. 6

3) Block description

1. Speech circuit section

• The receiver volume is an electronic volume type, this model is

switched in 2 steps.

2. Dial transmission section

• D.P. transmission: The CML relay and PC1 are turned on and off

for control in the DP calling system. (Refer to the attached sheet.)

• DTMF transmission: It is formed in the modem, and is output.

3. Speaker amplifier section

• Ringer volume : It is controlled by the combination of the attenuator

value of the LINE DRIVER in the modem and the ringer sending level sent from the modem.

• Speaker volume: It is controlled by the attenuator value of the LINE

DRIVER in the modem.

4. Ringer circuit section

• The ringer sound is formed in the tone of modem when CI signal is

detected. The amplifier circuit drives the speaker of the main body .

5 – 9

~~+

–

DPON

DPMUTE

DPON

IACR1 IACR2 IACR3

BIT7 BIT6 BIT5 BIT4 BIT3 BIT2 BIT1 BIT0 DAC GAIN

MIC GAIN L/O E

SPKR E

ADC GAIN

L/I E MIC E

TXRX

LOOP

LINEOUT

ATTENUATION

RXTXLOOP

MICBIAS

SEL

LINE SEL

CONTROL PWBTEL/LIU PWB

HANDSET

SP DRIVER

CUTI HS CI

CSWI PESNS FRSNS ORGSNS PSNS

BZOUT CML SPMUTE

VREFCONT MDMRST

FAX

ENGINE

FC200

ADC

DAC

SIN

DAC GAIN 0,6dB

SOUT

ADC GAIN 0,–4dB

MIC IN LPF

LINE IN LPF

SP OUT ENABLE

0,20,25,30dB

LINE DRIVER

LINEOUT ENABLE

MUTE,0, –6,–12dB

RHS RANK DRSNS

TXMUTE TELMUTE IA-RESET

SPMUTE

SPEAKER

TELMUTE

TELIN

CML

FAX MODEM FM209V

TELOUT

RXIN

TXOUT

SPKRP-P

MICP

LINEIN

LINEOUT

RTLOOP

(0:1) (1:0) (0:0) (1:1)

MIC ENABLE

1 0

LINE IN ENABLE

1 0

(0:0) (1:1) (1:0)

LNINSEL

MIC GAIN

VOL_C RXCONT W-TONE

VOL_A VOL_B

RCVOL LEDON VTHON

TXMUTE

4051

VOL_C

VOL_B

VOL_A

UX-68DE FO-78DE

5. Externally connected TEL OFF HOOK detection circuit section

• The circuit current detection is turned on together with OFF HOOK

of main body or OFF HOOK of externally connected TEL. ON of CML OFF (HS=L) is judged as OFF HOOK of externally connected TEL.

6. CI detection circuit

• CI is detected by the photocoupler which is integrated in series in

the primary side TEL circuit well proven in the existing unit.

5 – 10

Signal Name Description

CML Line connecting relay

(The circuit is located H: Line make in the TEL/LIU PWB.) L: Line break

SP MUTE Speaker tone mute control signal

(The circuit is located H: Muting (Power down mode)

in the TEL/LIU PWB.) L: Muting cancel (Normal operation)

Handset reception mute control signal

TEL MUTE H: Muting

L: Muting cancel

DPON Connecting DC circuit and DP generating

(The circuit is located

H: Line connect / Make

in the TEL/LIU PWB.) L: Line disconnect / Break

DPMUTE

Adjust the resistance

during make ratio

(The circuit is located

H: Muting

in the TEL/LIU PWB.) L: Muting cancel

TXMUTE Tx route mute circuit

(The circuit is located

H: Muting

in the control PWB.)

L: Muting cancel

4) Signal selection

The following signals are used to control the transmission line of TEL/ FAX signal. For details, refer to the signal selector matrix table.

[Control signals from output port]

VOL A VOL B VOL C

ON-HOOK ICM/OGM ICM/OGM

OUTPUT VALUE (GP02) (GP03) (GP04) Receiving MONITOR PLAY RINGER BUZZER DTMF/DP

X 0 1K 0 0 0 — — HIGH HIGH — — X 1 10K 1 0 0 HIGH HIGH MIDDLE1 — — — X 2 39K 0 1 0 MID 1 MID 1 MIDDLE2 — — — X 3 100K 1 1 0 MID 2 MID 2 MIDDLE3 — — — X 4 200K 0 0 1 MID 3 MID 3 LOW MIDDLE — — X 5 300K 1 0 1 — — — — — FIXED X 6 470K 0 1 1 LOW LOW — — FIXED — X 7 750K 1 1 1 — — — LOW — —

VOLUME SETTING

UX-68DE FO-78DE

(Example: TEL speaking)

NO Signal Name (CNLIUA)

1 TELOUT 2 TELIN 3 TELMUTE 4CI 5

6 RHS

Fig. 7

Signal Name Function

RHS

H:The handset is in the on-hook state. L: The handset is in the off-hook state.

CI Incoming call (CI) detection signal

[Signals for status recognition according to input signals]

Signal Name Function

TEL IN Receiving signal from line or modem

TEL OUT Transfer signal to line

SPOUT Speaker output signal

TXOUT

Transmission (DTMF) analog signal output from modem

RXIN

Reception (DTMF, others) analog signal

input

into modem

[Other signals]

5 – 11

NO Signal Name (CNLIUA)

7 RXIN 8 TXOUT 9 CML

+5V

12 +24V

,,,,,

TX/RX SIGNAL OGM/ICM/MEMO/PLAYBACK SIGNAL OGM/MEMO/RECORD SIGNAL

~~+

–

DPON

DPMUTE

DPON

IACR1 IACR2 IACR3

BIT7 BIT6 BIT5 BIT4 BIT3 BIT2 BIT1 BIT0

DAC

GAIN

MIC GAIN L/O E

SPKR E

ADC

GAIN

L/I E MIC E

TXRX LOOP

LINEOUT

ATTENUATION

RXTXLOOP

MICBIAS

SEL

LINE SEL

CONTROL PWBTEL/LIU PWB

HANDSET

SP DRIVER

CUTI HS CI

CSWI PESNS FRSNS ORGSNS PSNS

BZOUT CML SPMUTE

VREFCONT MDMRST

FAX

ENGINE

FC200

ADC

DAC

SIN

DAC GAIN 0,6dB

SOUT

ADC GAIN 0,–4dB

MIC IN LPF

LINE IN LPF

SP OUT ENABLE

0,20,25,30dB

LINE DRIVER

LINEOUT ENABLE

MUTE,0, –6,–12dB

RHS RANK DRSNS

TXMUTE TELMUTE IA-RESET

SPMUTE

SPEAKER

TELMUTE

TELIN

CML

FAX MODEM FM209V

TELOUT

RXIN

TXOUT

SPKRP-P

MICP

LINEIN

LINEOUT

RTLOOP

(0:1) (1:0) (0:0) (1:1)

MIC ENABLE

LINE IN ENABLE

1 0

(0:0) (1:1) (1:0)

LNINSEL

MIC GAIN

VOL_C RXCONT W-TONE

VOL_A VOL_B

RCVOL LEDON VTHON

TXMUTE

4051

VOL_C

VOL_B

VOL_A

NO Signal Name (CNLIUB)

1 RLYCNT 2

N. C.

NO Signal Name (CNLIUB)

3 DPON 4 DPMUTE 5 E-RLY

UX-68DE FO-78DE

[4] Circuit description of power supply PWB

1. Block diagram

2-1. Noise filter circuit

The input noise filter section is composed of L1, C1, C15 and C21 which reduces normal mode noise from the AC line and common mode noise to the AC line.

2-2. Rectifying/smoothing circuit

The AC input voltage is rectified by diode D1, 2, 3, 4 and smoothed by capacitor C2 to supply DC voltage to the switching circuit section.

Power thermistor TH1 suppresses inrush current at power switch-on.

2-3. Switching circuit

This circuit includes MOS FET Q1 and the gate drive circuit, and components around Q1.

In this circuit, the DC voltage supplied from the rectifying/smoothing section is converted into high frequency pulses by ON/OFF repetition of Q1.

[5] Circuit description of CIS unit

1. CIS (Contact Image Sensor)

Cis is an image sensor which puts the original paper in close contact with the full-size sensor for scanning, being a monochromatic type with the pixel number of 1,728 dots and the main scanning density of 8 dots/mm.

It is composed of sensor, rod lens, LED light source, light-conductive plate, control circuit and so on, and the reading line and focus are previously adjusted as the unit. Due to the full-size sensor, the focus distance is so short that the set is changed from the light weight type to the compact type.

Fig. 9

Fig. 8

5ms

1.984µs

2V(TYP) (White original paper)

Approx.5V

øT

CISCLK

5 – 12

2. Waveforms

The following clock is supplied from FC200 of the control board, and VO is output.

2-4. Control circuit

This circuit controls output voltage of 24V by adjusting ON period of Q1, looking at signal from photo-coupler PC1. In this operation IC1 takes charge of important part. The over current protection is performed by bringing Q1 to OFF state through detection of voltage of T1 subwiding. The over voltage protection is performed by operating the over current protection circuit through detection of zener diode ZD4 and short-circuiting of load.

2-5. +5V circuit

DC voltage supplied by rectifying the output of transformer T1 with diode D8 is stabilized by 3-terminal regulator IC1.

Noise

Filter

Circuit

Rectifying

Smoothing

Circuit

Switching

Circuit

(RCC system)

Regulator

Circuit

+5V

+24V

AC IN

Photo Coupler

1.6A/250V

Control

Circuit

UX-68DE FO-78DE

CHAPTER 6. CIRCUIT SCHEMA TICS AND PARTS LAYOUT

[1] Control PWB circuit Main control block 1/6

6 – 1

BDEFG

HCA

BDEFG

HCA

107

7374757677

798082838485868789909192939496

100

101

33343536293031

114

115

116

117

118

103

104

105

106

119

140

123

102

53,56

64,88

95,108

132

7,134

129

131

135

133

130

136

137

138

139

+5V

C155

0.1

C153

+5V

141

142

143

144

(3-2A) (3-3B)

SYSCLK MIRQ

R150

10K

C118

1000P

R107 33K

R108 33K

R100 33K

RA3

270 x 4

RA4

270 x 4

(2-6A)

(3-4B)

C133

C159

C158

C156

C151

C132

C114

C117

2345689

111213151617181920222324252627

128

127

120

12257121

126

124

125

113

112

111

109

110

ABCDE

A16

A15

A14

A13

A12

A11

A10

A9A8A7A6A5A4A3A2A1

RA6

270 x 4

RA13

270 x 4

IKJ

(2-6A)

(3-4B)

(2-4D)(3-3B)

(2-4A)

(2-4D)

(3-3B)

R123 100

R125 100

VBT

C172

R168

C173

0.1 DG

BATRST

+5V

VCC

GND

OUT

C171

MCS

CE1

ROMCS

(2-2D)

CE2

IC7

XC61

C175

2200P

R167

10M

C177

22P

C176

18P

32.768kHz

(5-2D)

+VREF

(5-2D)

–VREF

(5-6D)

VIN

(5-1I)

THADI

(6-1G)

BZOUT

(5-5F)

TPA

(5-5F)

TPB

(5-5F)

TPA

(5-5F)

TPB

C178

DGDG

DG DG DG DG

C110 1000P

C109 1000P

C108 1000P

C107 1000P

RA1

270 x 4

(5-5F)

VTHON

(5-5F)

LEDON

(3-2B)

MDMRST

(6-3C)(6-5E)

RCVOL

C113

0.1

+5V

CNPN-16 CNPN-15 CNPN-14 CNPN-13

CNPN-4 CNPN-5 CNPN-6 CNPN-7 CNPN-8 CNPN-3 CNPN-9 CNPN10 CNPN-11

KEN1A KEN2A KEN3A KEN4A

E SEN0 SEN1 SEN2 SEN3 SEN4 SEN5 SEN6 SEN7

L108

HM601

R169

120

RA14

470 x 4

RA15

470 x 4

A23

A22

A21

A20

A19

A18

A17

A16

A15

A14

A13

A12

A11

A10

A9A8A7A6A5A4A3A2A1

ROMCS

CS1

CS0

MCS

SYNC

REGDMA

WAIT

RAS

CAS0

CAS1

DWR

WRPROT

VBAT

CNTH-13

LATCH

CNTH-15

DATA

CNTH-14

PCLK

CNTH-3

STRB1

CNTH-4

STRB2

CNTH-11

STRB3

CNTH-12

STRB4

RA11

470 x 4

RA12

270 x 4

C180 22P

C181 22P

C139 22P

C140 22P

C194 22P

C193 22P

C179 22P

CNCIS-4

CNCIS-5

CISCLK

D[7-0]

A[17-0]

R116 150

R120 470

L102

HM601

(4-2D)

PSNS

(4-5D)

ORGSNSI

(4-5D)

FRSNSI

(4-3D)

PESNS

CNLIUB-4

DPMUTE

C221

1000P

R148

470

RA5

470 x 4

R124 33K

R122 33K

R118 33K

R119 33K

CNLIUB-5

E-RLY

CNLIUB-3

DPON

CNPW-8

PSAVE

CNLIUB-1

RLYCNT

(4-6D)

CSWI

C220 C222 C217 C218

RA10

470 x 4

R143

470

R147

33K

(6-2I)

SPMUTE

CML

(5-2A)

VREFCONT

(4-4D)

CUTI

GPIO20

GPIO19

GPIO18

GPIO17

GPIO16

GPIO15

GPIO14

GPIO13

GPIO12

GPIO11

GPIO10

GPIO9/FRD

GPIO8/FWR

GPIO7/FCLE

GPIO6/FALE

GPIO5/FREADY

GPIO4

GPIO3

GPIO2

GPIO1

GPIO0

VIDCTL0/FCS1

VIDCTL1

CLK1

CLK2

START

STRB3

STRB2

STRB1

STRB0

PCLK

PDAT

PLAT

STRBPOL

D0 D1 D2 D3 D4 D5 D6 D7 TSTCLK SYSCLK MIRQ RESET DEBUG TEST

VSS

VDD VDD VDD VDD VDD VDD VDD VDD ADXG

ADGA ADGD

ADVA

BATRST

PWRDWN

XOUT

XIN

+VREF

–VREF / CLREF

VIN

THADI

TONE

SM0 SM1 SM2 SM3

GPO0 GPO1 GPO2 GPO3

VDRAM

OPI0 OPI1 OPI2 OPI3

LEDCTL

LCDCS

OPO0 OPO1 OPO2 OPO3 OPO4 OPO5 OPO6

38 : OPO7

R166

10K

RA2

470 x 4

R152

10K

RA9

470 x 4

R104

R117

470

R105

R151 33K

R149 33K

R121 33K

(2-4A)(3-3B)

IC3

FC200

A17

R127

270

RA8

270 x 4

RA7

270 x 4

C135

68P

C136

68P

DG DG

R164

10K

2SC2412K

RA16

470 x 4

CA2

CA1

DG DG

N.M.

PHIT

C142

C143

N.M.

FCS

R213

270

FREADY

FALE

FCLE

FWR

FRD

R219

33K

R214

270

R215 270

R216 270

R217 270

R218 270

C134

C160

C157

C154

C152

C131

C115

C116

R126 270

R163

10K

(2-1D)

(2-2D)

(2-3D)

(2-2D)

(1-6B)

CML

(1-5A)(6-4E)

(1-5A)

C205 C200 C197

CNLIUA-9

CNLIUA-5

CNLIUA-4

CMLHSCI

N.M.

1000P x 3

1000P x 4

C133,C159,C158,C156,C151,C132,C114,C117: 1000P x 8

UX-68DE FO-78DE

Memory block 2/6

BDEFG

HCA

BDEFG

HCA

2029192818

172515231426132731

IO8

IO7

A14

IO6

A13

IO5

A12

IO4

A11

IO3

A10

IO2

IO1

A5 VDD

VSS

27A022

CS2/OE

A[17~0]

(1-5I)

D[7~0]

(1-6I)

(1-3H)RD(1-3H)

+5V

C216

0.1

D7D6D5D4D3D2D1

IC10

27C020

A15 D7

A14 D6

A13 D5

A12 D44A11 D3

A10 D2

A9 D1

A8 D0

A75A66A5

PGM

VCC

VPP

A2A1A0 GNDCEOG

IC6

W24258S-70LE

D7D6D5D4D3D2D1

VBT

C161

0.1

(1-3H)

VBT

R128

22K

ROMCS

A16

A15

A14

A13

A12

A11

A10A9A8A7A6A5A4A3A2A1A0

A16

CS1

CE1

(1-3H)

A17

L110

I/O727I/O6

FCLE

CLE

I/O525I/O4

FALE

ALE

I/O321I/O2

FWR

I/O119I/O0

CE2

VCC

FREADY

R/B

GND

FRD

FCS

IC4

KM29W040

D7D6D5D4D3D2D1

+5V

C119

0.1

VCC

VSS

R109

R133

R132

R131

R130

R129

R154

R153

(1-4B)

(1-1I)

(1-4B)

(1-3B)

100 x 8

6 – 2

UX-68DE FO-78DE

Modem block 3/6

BDEFG

HCA

BDEFG

HCA

C130

0.01

R101

270

D6D5D4D3D2D1D0

A1A2A3

1920212223

RS4

RS3

RS2

RS1

RS0

78D779D680D581D482D383D286D188D091CS92

READ90WRITE

108

IRQ1

115

RESET13EN85

D[7~0]

(1-3H)

R187

MIRQ

(1-6F)

A[4~0]

MDMRST

(1-1D)

MCS

MAG

121

IRQ2

107

RTS

CTS

TXD

DCLK

RXD11RLSD

R141

10K

RESERVED/CSBR

119

R113

270

+5V

SYSCLK

(1-6F)

621

XCLK

YCLK

CLR

CLK

PRE

L100

HM601

R106

470

L103

HM601

C111

IC2

WT74

L101

HM601

101

102

104

105

109

110

111

R134

470

R135

470

R138

10K

TXMUTE

TELMUTE

DG DG DG DG DG DG

R103

C106

10P

C105

10P

R102

100

122

116

117

287414043344746373635

1,2,53,103,118,123,124,128

38,39,44,49,59,64,65,74

MAG

C166

0.1

C167

0.1

10/50C110/50

MAG

(6-3C)

SPOUT

(6-6E)

TELOUTI

(6-2D)

SIGTX

(6-4E)

SIGRX

C168

0.1

R160

2.2K

R162

MAG

CNDR-1

C147

2200P

R137

470

+5V

R110

100K

120

CNTH-6

RANK

CNLIUA-6

RHS

R115

470

R139

470

+3.3V

L106

HM601

100

112

106

114

125

113

126

+5V

L104

HM601

C127

0.1

+3.3V

R161

47/25

C169

127

C146

+5V

L105

HM601

MAG

MICP-P

MICM-P

MICBIAS-P

SPKRP-P

SPKRM-P

LINEIN-P

LINEOUT-P

VREF-P

VC-P

RESERVED

N.C./MICM-S

N.C./SPKRP-S

N.C./LINEIN-S

N.C./VREF-S

N.C./MICP-S

N.C./MICBIAS-S

N.C./SPKRM-S

N.C./LINEOUT-S

N.C./VC-S

N.C.

XTLO

XTLI

N.C./SOUT-S

SR3IN

SOUT-P

N.C./ICLK-S

ICLK-P

IA1CLK

N.C./SIN-S

SIN-P

SR4OUT

N.C./MCLK-S

IACLK

MCLK-P

N.C./FSYNC-S

SA1CLK

FSYNC-P

N.C./CTRLSIN-S

CTRLSIN-P

SR1IO

EYEXY

EYECLK

EYESYNC

N.C./IARESET-S

IARESET-P

GPO0

W-TONE/GPO1

VOL-C/GPO2 VOL-B/GPO3 VOL-A/GPO4

MONITOR/GPO5

GPO6 GPO7

GPI7

GPI6

GPI5

GPI4

GPI3

GPI2

GPI1

GPI0

VDD1(+3.3VDD)

VDD2(+3.3VDD)

VDD3(+3.3VDD)

VDD4(+3.3VDD)

VDD5(+3.3VDD)

AVDD-P(+3.3VIAD)

DGND1

DGND2

DGND3

DGND4

DGND5

DGND6

VGG(+5VDD)

DVAA(+3.3VDA)

N.C./AVDD-S(+3.3VIAD)

AGND1

AGND2

AGND3

AGND4

AGND5

VAA-P(+5VIAA)

VAA-S(+5VIAA)

R142

33K

R114

33K

R140

32.256MHz

CNLIUA-3 CNLIUB-2

(1-6I)

IC4

FM209V

C198

1000P

C199

1000P

(6-1C)

W-TONE

VOL_C VOL_B VOL_A

C219

1000P

TXMUTE

R136

R158

R112

R222

N.M.

R220

33K

C124

N.M.

C112

0.1

C227

N.M.

R123

N.M.

R111

100K

C137

0.1

C129

C150 1

C149 1

C125 1 C126 1

C148

C145

0.1

C170

0.1

C128

(6-1C)

(6-2G)

6 – 3

UX-68DE FO-78DE

Sensor/Reset/Power supply block 4/6

6 – 4

BDEFG

HCA

BDEFG

HCA

CNCSW-1

CNCSW-2

CSW

(1-4A)

CNFRS-1

CNFRS-2

FRSNS

(1-3A)

CNPN-12

ORGSNS

(1-3A)

+24V

C120

2200P

CSWI

C122

2200P

FRSNSI

C183

2200P

ORGSNSI

PESNS

R191

R170

(1-3A)

PSNS

DGDG

PESNS

PSNS

PI2

SG206

PI1

CNCUT-1

CNCUT-2

CUT

(1-5A)

C121

CUTI

+5V

R211

5.6K

BAT1

CR2032

RB705D

VBT

<VBT>

+3.3V

1SS355

REG100

XC62

C192

0.1

DG DG

+5V

+24V

+24VA

C10

22/50

C223

0.1

R206

R207

N.M.

C11

47/25

C224

0.1

+5V

+24V

+5V

+24V

CNLIUA-10

CNLIUA-11

CNPN-1

CNLIUA-12

CNPW-2

CNPW-1

CNPW-7

CNPW-5

CNPW-6

CNPW-3

CNPW-4

R212

200

100/50

CNCUT-3

R155

C229

C228

N.M.

+5V

CNPN-2

C206

1000P

+5V

C196

1000P

N.M.

2.2K(1/2W)

N.M.

UX-68DE FO-78DE

Video processing/Motor drive / Thermal block 5/6

6 – 5

BDEFG

HCA

BDEFG

HCA

R157

5.1K

+5VO

2SA1037

CNCIS-1

<VO>

(1-1F)

<VIN>

VIN

C164

1000P

+5VO

CNCIS-3

CNCIS-2

<DG>

+5V

+24V

CNCIS-7

+24V

C165

C141

0.1

GLED

CNCIS-6

C144

0.1

LEDON

R165

5.1K DG

2SA1037

(1-5A)

VREFCONT

(1-1F)

VREF+

+5V

R146

20K

(1-1F)

VREF–

R145

30K

R144

43K

9161514131211

1234567

TPA

TPB

TPA

TPB

VTHON

LEDON

(1-1E)

(1-1D)

+24V

FU100

KAB2402

100(1W)

VMT

TPBD

TPAD

TPBD

TPAD

VTHON

LEDON

CNMT-5

CNMT-6

CNMT-1

CNMT-2

CNMT-3

CNMT-4

(5-3E)

(5-4B)

IC1

ULN2003A

1B2B3B4B5B6B7B

COM

1C2C3C4C5C6C7C

VTHON

(5-5I)

+24V

1SS355

RY1

DQ1U24VDC

+24V

VTH

CNTH-1

VTH

CNTH-2

VTH

CNTH-16MGCNTH-7MGCNTH-8MGCNTH-9

R156

22K

+5V

CNTH-10

+5V

(1-1E)

CNTH-5

THI

THADI

C163

R209

20K

R208

470K

10/50

R159

(5-5I)

C226

N.M.

+5VO

C174

N.M.

C162

1000P

C138

1000P

C100

1000P

C101 C102 C104 C103

N.M.

1000P x 4

UX-68DE FO-78DE

Analog signal block 6/6

6 – 6

BDEFG

HCA

BDEFG

HCA

–

+5V

+5VA

+5V

–

+5V

–

+5VA

+5V

+24VA

+5V

TELOUT

CNLIUA-1

C195

R193

51K

C203

820P

R194

3.3K

IC11

2904

R192

13k

R195

100

N.M.

C182

R176

C184

6.8

1SS355

TELOUTI

(3-4H)

(3-3H)

SPOUT

452

178

+5V

R198

100K

C209

220P

R210

220K

47/25

SP+

SP–

CNSP-1

CNSP-2

(1-5A)

SPMUTE

C210

DG DG

(1-1E)

BZOUT

R204

10K

C190

4700P

R205

20K

DG DG

R201

100K

C215

0.01

R203

C213

IC12

NJM2113

L111

47/25

DG DG

CNMIC-1

CNMIC-2

CNMIC-3

DGDG

R181

R180

R182

C225

N.M.

C186

R178

12K

PDTC114

RCVOL

(1-1D)

RXIN

CNLIUA-7

C207

R173

118K

C208

33P

R175

3.3K

IC11

2904

R197

118K

R171

R177

C185

1SS355

SIGRX

(3-4H)

CNLIUA-2

C1891R179

10K

PDTC114

CML

(1-5A)

TELIN

C204

0.022

R196

47K

C202

0.1 R172

30K

R174

N.M.

C201

PDTC114

RCVOL

(1-1D)

IC9

HCF4051

+5V

678

C191

(3-1D)

VOL_C

(3-1D)

VOL_B

(3-1D)

VOL_A

R184

750K

R183

470K

R185

300K

R202

200K

R186

100K

R188

39K

R189

10K

R190

R199

15K

C214

0.1

CNLIUA-8

TXOUT

C211

0.1

C212

L107

1.5K

SIGTX

W-TONE

C188

0.1

C187

0.1

R221

IN/OUT

OUT/IN

VSS

VDD

CONT

IC8

TC4S66

N.M.

TXMUTE

PDTC114

X0X1X2X3X4

X5X6X7

VDD

VSS

11109

(3-1C)

(3-1D)

(3-4H)

UX-68DE FO-78DE

Control PWB parts layout (Top side)

6 – 7

UX-68DE FO-78DE

Control PWB parts layout (Bottom side)

6 – 8

UX-68DE FO-78DE

6 – 9

[2] TEL/LIU PWB circuit 1/2

BDEFG

HCA

BDEFG

HCA

–

+5VA

+5V

VREF

–

VREF

–

VREF

L2B

R-5C

PC4

N.M.

+5VA

N.M.

R113

+5V

+24VA

CNTLJ-3

CNLNJ-2

JP7

JP8

CNLNJ-3

JP6

JP3

CNLNJ-4

AR1

RA-501P-V6

AR2

RA-501P-V6

ARG

CNLNJ-5

CNTLJ-2

JP9

JP1

JP5

C103

0.022 L3

4.7mH

C105

0.022

N.M.

L2A

R-5C

CML

0.47

R102

120K

47K(1/2W)

1N4148

ZD3

BZX79B20V

PC6

TLP521

0.47 R101

160

I2165

C104

0.033

C113

N.M.

–

REC1

S1ZB60

CNLNJ-6

PC1

R104

ZD6

BZX79B3V3

ZD7

BZX79B3V3

+5V

C11

22/50

R126

R134

C116

C115

0.01

R131

2.2K

R139

C119

100P

R138

240K

IC102

2904

R143

10K

TXOUT

CNLIUA-8

R132

C117

R136

3.3K

C118

0.056

R133

390

R141

30K

C123

1200P

C121

1000P

R144

30K

IC102

2904

RXIN

CNLIUA-7

R142

3.3K DG

C109

0.1

C120

0.1

IC101

2904

IC102

2904

R118

20K

R121

30K

R120

10/50

DGDG

CNHJ-4

CNHJ-1

TX+

C101

0.01

CNHJ-2

CNHJ-3

RX+

RX–

R-5C

R114

1.5K

R115

22/50

C102

0.01

C106

0.047

R116

10K

ZD4 ZD5

N.M.

C111

1000P

R117

16K

C107

1000P

R129

3.3K

C108

C112

DGDGDG

N.M.

IC101

2904

TELOUT

CNLIUA-1

1N4148

R-5C

4.7/50

R119

150

R122

10K

R123

3.3K

IC101

2904

C110

2200P

R124

47K

C10

2.2/50

TELIN

CNLIUA-2

R125

24K

R128

8.2K

TELMUTE

CNLIUA-3

Q102

PDTC114

JP4

VA1

DSS-301L

Q101

BC847B

JP2

ZD1

BZX79B20V

N.M.

JP12

N.M.

JP11

N.M.

JP10

N.M.

CNTLJ-1

C114

Q113

+5V

R127

R130

Q104

R137

750

N.M.

R140

22K

R135

22K

R106

PC2

TLP627

VA2

SIOV-S05K60T

2N5401

2SA1807

R105 470K

820(3W)

10/50

R103

13K

R107

20K

PC3

TLP521

R111

10K

ZD2

BZX79B6V8

3.3/50

R110

BS108

R108

R112

PC5

TLP521

CNTLJ-4

CNLNJ-1

4.7mH

R109

TX–

NOTE:

These marks are all satety-cirtical parts.

UX-68DE FO-78DE

6 – 10

TEL/LIU PWB circuit 2/2

BDEFG

HCA

BDEFG

HCA

+5V

DPON

CNLIUB-3

DPMUTE

CNLIUB-4

E-RLY

CNLIUB-5

R148

470

PC2

TLP627

Q108

PDTC114

Q110

PDTC114

Q109

R149

470

R151

PC3

TLP627

PC4

CNLIUA-4

R152

100K

DGDG

C125

0.1

PC6

TLP521

CNLIUA-5

R153

470

C126

0.1

PC5

TLP521

N.M.

RHS

CNLIUA-6DGCNHS-1

CNHS-2

SW1

HOOK SW

CNLIUA-10

+5V

CNLIUA-11DGCNLIUA-12

+24V

R145

C12

47/25

C13

22/50

C122

0.1

C124

0.1

+5VA

+24VA

R147

CNLIUA-9

CML

1N4148

Q106

PDTC114

CML

RLYCNT

CNLIUB-1

PC1

Q107

R150

N.M.

+24V

R146

Q105

N.M.

C127

0.01

NOTE:

These marks are all satety-cirtical parts.

UX-68DE FO-78DE

TEL/LIU PWB parts layout (Top side)

6 – 11

UX-68DE FO-78DE

6 – 12

TEL/LIU PWB parts layout (Bottom side)

UX-68DE FO-78DE

[3] Power supply PWB circuit

6 – 13

BDEFG

HCA

BDEFG

HCA

S3L20U-4004P15

C13

PTTP124

FB1

R11

ZD7

RD20ESAB

PC2

PC123YS

2SC4210

R21

150K

2SC4210

R12

180K

ZD4

RD30FB

R20

4.7K

IC1

UPC29M05AHF

R19

4.7K

JUMPER

CCP2E100(4A)

R25

10K

C16

100/10

0.47

R16

22K

C12

0.1

R15

330K

R14

1.5K

R13

4.7K

PC1

PC123YS

R18

27K

2SC2412K

ZD5

RD6.2SB

VR1

R17

8,2K

C10

2200/16

SR140

N.M.

C23

R24

ZD6

RS208

330

2200P

PC2

PC123YS

ZD2

RD2.0SB

1SS355

PC1

C17

1000P

C24

0.22

FS5KM

1000P

ZD1

RD27SB

2SD2114K

2SC2412K

470

R10

0.33

47K

3900P

1.6A/250V

CN1

1.6A/250V

0.22

3.3M 1

ERZV07D471

ELF15N003A

C15

2200P

C21

D2D1

TH1

89.2

N.M.

CN2

+5V

+24V

PSAVE

68/400

560/35

*R5

1.5K *R6

18K

*:ADJUSTMENT RESISTOR

ERA15-06 x 4

CH2 W1

100.0V

25.00us

-100.0V

-25.00us

GND

20V/div

5us/div

CH2 W1

1200V

25.00us

-800V

-25.00us

GND

200V/div

5us/div

CH2 W1

450V

5.02ms

-50V

-4.9Sms

GND

50V/div

1ms/div

CH2 W1

50.0V

25.00us

-50.0V

-25.00us

GND

10V/div

5us/div

CH2 W1

50.0V

25.00us

-50.0V

-25.00us

GND

10V/div

5us/div

UX-68DE FO-78DE

Power supply PWB parts layout (T op side)

6 – 14

Power supply PWB parts layout (Bottom side)

C13

IC1

ZD7

FB1

C10

C16

ZD4

VR1

R24

ZD6

R10

CN1

C15

C21

J10

J11

J12

JW1

TH1

C24

PC2

PC1

CN2

R8R9Q3

ZD1

C23

C4R4

R11

R16

R25

R15

C12

ZD5

R17

Q6 R12

R19

R18

R21

R13

R20

R14

C17

ZD2

UX-68DE FO-78DE

[4] Operation panel PWB circuit

6 – 15

BDEFG

HCA

BDEFG

HCA

LD4

1SS270

CNLCD-11

CNPN-5

LD5

1SS270

CNLCD-12

CNPN-6

123

456

VOLUME

SEN0

SEN1

LD6

1SS270

CNLCD-13

CNPN-7

789

FUNC

SEN2

LD7

1SS270

CNLCD-14

CNPN-8

RESO/MODE

SEN3

1SS270

CNLCD-4

CNPN-3

SEN4

02 04

1SS270

CNPN-9

STOP

SEN5

START COPY

1SS270

CNPN-10

HOLD

REDIAL

SEN6

SPEED SPEAKER

CNPN-11

PLAY

REC

SEN7

REPEAT DELETE

CNPN-16

KEN1A

CNPN-15

KEN2A

CNPN-14

KEN3A

CNPN-13

KEN4A

CNPN-12

ORGSNS

SW-169-72AU

CNLCD-6

CNPN-4

CNLCD-2

+5V

CNPN-2

+5V

CNLCD-1

CNPN-1

CNLCD-5

R/W

CNLCD-3

C2 C1

6.2K

12345678910

11 12

13 14

15 16

CNPN

SEN4

SEN0

SEN2

SEN5

SEN7

KEN4A

KEN2A

SEN1

SEN3

SEN6

ORGSNS

KEN3A

KEN1A

+5V

12345678910

11 12

13 14

CNLCD

DGVOR/W

N.C.

LD4

LD6

RSEN.C.

N.C.

LD5

LD7

+5V

ORGSNS

N.M.

NOTE: Since the parts of PWB cannot be supplied, change it as a unit.

UX-68DE FO-78DE

6 – 16

M E M O

UX-68DE FO-78DE

CONTENTS

PARTS GUIDE

UX-68

MODEL FO-78

Because parts marked with " " are indispensable for the machine safety maintenance and operation, it must be replaced with the parts specifi to the product specification.

1 Cabinet, etc.

2 Scanner unit

3 Upper cabinet

4 Document guide upper

5 Drive unit

6 Packing material & Accessories

7 Control PWB unit

8 TEL-LIU PWB unit

9 Power supply PWB unit

Index

UX-68DE FO-78DE

[1] Cabinet, etc.

– 1 –

CIS EARTH CABLE

SCANNER UNIT

DOCUMENT GUIDE UPPER

B3x2

B7x2

RELEASE

DRIVE UNIT

MOTOR

CABLE

CAM

SWITCH

CABLE

NO.

PAR TS CODE

PRICE

RANK

NEW

MARK

PART

RANK

DESCRIPTION

UX-68DE FO-78DE

– 2 –

[1] Cabinet etc.

1 DCEKK201CFF10 N E Operation panel unit [68]

DCEKK201CFF11 N E Operation panel unit [78] 2 CCNW-212AXH01 AK C Panel cable ass’y 5 MSPRC2954FFZZ C Hopper spring 6 NGERP2318XHZZ AD C Pinion gear 7 PGIDM2560XHSA AC C Hopper,guide,left [68]

PGIDM2560XHSC C Hopper,guide,left [78] 8 PGIDM2561XHSA AC C Hopper,guide,right [68]

PGIDM2561XHSC C Hopper,guide,right [78] 9 PHOP-2104FFSA C Hopper cover [68]

PHOP-2104FFSC C Hopper cover [78]

11 QSW-M2296XHZZ AD B Door sensor 12 CCNW-215AFF01 C Speaker ass’y 13 GCABB2343FFSA D Lower cabinet [68]

GCABB2343FFSC D Lower cabinet [78]

14 MSPRP3119XHZZ AC C Panel lock lever spring 15 MSPRP3123XHZZ AC C Speaker holder lever spring 16 DCEKL227CFF01 E TEL/Liu PWB unit

17 GCASP2110FFSD N C PWB case,top [68]

GCASP2110FFSE N C PWB case,top [78]

18 GCASP2111FFSA N C PWB case,bottom [68]

GCASP2111FFSC N C PWB case,bottom [78]

19 MLEVP2320XHZZ AC C Hook switch joint lever

20 QACCE2013BMZZ B AC cord ass’y

21 RDENT2144XHZZ BA E Power supply PWB unit 22 GDAI-2083FFZZ C Paper support guide 23 MLEVP2316XHZZ AC C Paper sensor lever 24 MSPRD3116FFZZ C Paper sensor lever spring 27 PGIDM2563XHSA AE C PO guide [68]

PGIDM2563XHSC AC C PO guide [78]

28 LBSHP2112XHZZ AB C Platen bearing 29 LFRM-2208XHZZ AF N C Head frame 30 LHLDZ2184XHZZ AC C Head holder,left 31 LHLDZ2185XHZZ AC C Head holder,right 33 MSPRC3112FFZZ C Head spring 1 34 MSPRC3148FFZZ C Head spring 2 36 NGERH2478XHZZ AB C Platen gear 37 NROLR2425XHZZ AP C Platen roller 39 QCNW-209AXHZZ AH C Head cable 40 QCNW-210AXHZZ AC C Head earth cable 41 RHEDZ2059XHZZ BF B Thermal head 45 CPWBX3094FF01 N E Control PWB unit(Without ROM) 46 GDAI-2082XHSA AD C Handset cover [68]

GDAI-2082XHSC C Handset cover [78]

47 LSTPP2054XHZZ AC C Panel stopper 49 MLEVP2319XHZZ AC C Hook switch lever 52 PGIDM2566XHZZ AC C Head guide

53 RCORF2064XHZZ AF B Core(TRA31) 54 HPNLH2393XHSJ N D Decoration panel [68]

HPNLH2393XHSP N D Decoration panel [78]

55 LHLDW1033CE00 AA C Band 56 LPLTM3107XHZZ AD N C Earth plate 57 PSHEZ3410FFZZ N C Jack sheet

58 MLEVP2321XHZZ AN C Release lever B1 LX-BZ2138FFZZ C Screw(2x6) B3 XEBSD30P08000 AA C Screw(3x8) B4 XBBSD30P06000 AA C Screw(3x6) B5 XBPSN40P06K00 AA C Screw(4x6) B7 XEBSD30P12000 AA C Screw(3x12)

NO.

PAR TS CODE

PRICE

RANK

NEW

MARK

PART

RANK

DESCRIPTION

UX-68DE FO-78DE

[2] Scanner unit

– 3 –

[2] Scanner unit

1 LBSHP2110XHZZ AB C Back roller bearing 2 LFRM-2209FFZZ C Scanner frame 3 LHLDZ2180XHZZ AC C CIS support,left 4 LHLDZ2181XHZZ AC C CIS support,right 5 MLEVP2317XHZZ AB C CIS release lever 6 MSPRC3117FFZZ C CIS spring 7 NGERH2479XHZZ AB C Back roller gear 8 NGERH2480XHZZ AB C Reduction gear,17/28Z

9 NGERH2481XHZZ AB C Reduction gear,17/23Z 10 NROLR2375XHZZ AL C Feed roller 11 NROLR2428XHZZ AP C Back roller 12 NSFTZ2273XHZZ AF C Feed roller shaft 13 PGIDM2562XHZZ AD C Document guide lower 15 QCNW-4814XHZZ AG C CIS cable 16 QCNW-213AXHZZ AC C Front sensor cable 17 QSW-M2293XHZZ AE B Front sensor 18 RUNTZ2054XHZZ BE B CIS unit 19 LHLDW1033CE00 AA C Band

20 RCORF2063XHZZ AF B Core 21 PSHEZ3543XHZZ AE N C CIS earth sheet 22 QCNW-352AFFZZ N C CIS earth cable

UX-68DE FO-78DE

– 4 –

[3] Upper cabinet

B2x3

[4] Document guide upper

NO.

PAR TS CODE

PRICE

RANK

NEW

MARK

PART

RANK

DESCRIPTION

[3] Upper cabinet

1 CCNW-212AXH01 AK C Panel cable ass’y 3 GCABA2342FFSX N D Upper cabinet [68]

GCABA2342FFSY N D Upper cabinet [78]

4 JBTN-2257FFSA C 12 key [68]

JBTN-2257FFSC C 12 key [78]

5 JBTN-2258FFSA C Start key [68]

JBTN-2258FFSC C Start key [78]

6 JBTN-2261FFSA C Direct key [68]

JBTN-2261FFSC C Direct key [78] 7 DCEKP203CFF02 N E Operation panel PWB unit 8 JBTN-2262FFSA N C TAD key [68]

JBTN-2262FFSC N C TAD key [78]

B2 XUBSD20P06000 AA C Screw(2x6)

(Unit)

901 DCEKK201CFF10 N E Operation panel unit [68]

DCEKK201CFF11 N E Operation panel unit [78]

NO.

PAR TS CODE

PRICE

RANK

NEW

MARK

PART

RANK

DESCRIPTION

[4] Document guide upper

1 LPLTG2911XHZZ AE C Separator rubber 2 LPLTP2908XHZZ AE C Separator plate 3 LPLTP3051XHZZ AB C Feed plate 4 MSPRT3140FFZZ C Separate spring 5 MSPRT3139FFZZ C Feed spring 6 PGIDM2554FFZZ C Document guide upper 7 PSHEZ3517FFZZ C Blind sheet

NO.

PAR TS CODE

PRICE

RANK

NEW

MARK

PART

RANK

DESCRIPTION

UX-68DE FO-78DE

– 5 –

[5] Drive unit

1 LFRM-2207XHZZ AF C Drive unit frame 2 LPLTM3049XHZZ AD C Motor plate 4 MCAMP2027XHZZ AC C Cam 5 MLEVP2311XHZZ AB C Planet lever A 6 MLEVP2312XHZZ AB C Planet lever B 8 MLEVP2314XHZZ AB C Mode lever

9 MSPRC2735XHZZ AC C Planet gear spring 10 MSPRC3110XHZZ AB C Cam spring 12 NGERH2278XHZZ AC C Planet gear 13 NGERH2379XHZZ AC C Idler gear,25Z 15 NGERH2391XHZZ AC C Reduction gear,17/30Z 17 NGERH2475XHZZ AB C Reduction gear,17/43Z 20 QCNW-4933XHZZ AC C Cam switch cable 21 QSW-F2224SCZZ AE B Cam switch 22 RMOTZ2148XHZZ AT B Motor

B3 XEBSD30P08000 AA C Screw(3x8)

UX-68DE FO-78DE

[6] Packing material & Accessories

– 6 –

(2)

(1)

(4)

(3)

TAPE

ORIGINAL DOCUMENT SUPPORT SIDE

AC CORD

NO.

PARTS CODE

PRICE

RANK

NEW

MARK

PART

RANK

DESCRIPTION

[6] Packing material & Accessories

1 TINSG4052FFZZ N D Operation manual [68]

TINSG4053FFZZ N D Operation manual [78]

2 DUNTK204CFFBG E Handset [68]

DUNTK204CFFWH E Handset [78]

3 QCNW-3976XHBG AK C Handset cord [68]

QCNW-3976XHOW AK C Handset cord [78] 4 PHOP-2105XHZZ AD C Original document support 5 QCNW-4649FFZZ C Telephone line cord 6 SPAKP3385FFZZ D Vinyl cover 7 SPAKA287BFFZZ D Packing add.,left 8 SPAKA288BFFZZ D Packing add.,right 9 SPAKA289BFFZZ D Pad

10 SPAKC168BFFZZ D Packing case 11 TLABM433AFFZZ N D Pop label 16 PGIDM2578XHZZ AE C Paper roll shim,right 17 PGIDM2579XHZZ AE C Paper roll shim,left 26 TLABM363BFFZZ N D Box label 27 TPAPK2205FFZZ N S Fax paper(Initial starter roll 10m)

NO.

PAR TS CODE

PRICE

RANK

NEW

MARK

PART RANK

DESCRIPTION

UX-68DE FO-78DE

– 7 –

[7] Control PWB unit

1 UBATL2046SCZZ AK B Battery(CR2032T34) [BAT1] 2 VCEAGA1HW106M AA C Capacitor(50WV 10µF) [C1] 3 VCEAGA1EW476M AA C Capacitor(25WV 47µF) [C3] 4 VCEAGA1HW106M AA C Capacitor(50WV 10µF) [C4] 5 VCEAGA1EW476M AA C Capacitor(50WV 47µF) [C5] 6 VCEAGA1EW476M AA C Capacitor(25WV 47µF) [C7] 7 VCEAGA1HW107M AA C Capacitor(50WV 100µF) [C8] 8 VCEAGA1HW106M AA C Capacitor(50WV 10µF) [C9]

9 VCEAGA1HW226M AB C Capacitor(50WV 22µF) [C10] 10 VCEAGA1EW476M AA C Capacitor(25WV 47µF) [C11] 11 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C100] 12 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C101] 13 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C102] 14 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C103] 15 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C104] 16 VCCCTV1HH100D AA C Capacitor(50WV 10PF) [C105] 17 VCCCTV1HH100D AA C Capacitor(50WV 10PF) [C106] 18 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C107] 19 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C108] 20 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C109] 21 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C110] 22 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C111] 23 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C112] 24 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C113] 25 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C114] 26 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C115] 27 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C116] 28 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C117] 29 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C118] 30 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C119] 31 VCKYTV1HB222K AA C Capacitor(50WV 2200PF) [C120] 32 VCKYTV1HB222K AA C Capacitor(50WV 2200PF) [C122] 33 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C125] 34 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C126] 35 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C127] 36 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C128] 37 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C129] 38 VCKYTV1HB103K AB C Capacitor(50WV 0.01µF) [C130] 39 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C131] 40 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C132] 41 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C133] 42 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C134] 43 VCCCTV1HH680J AA C Capacitor(50WV 68PF) [C135] 44 VCCCTV1HH680J AA C Capacitor(50WV 68PF) [C136] 45 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C137] 46 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C138] 47 VCCCTV1HH220J AA C Capacitor(50WV 22PF) [C139] 48 VCCCTV1HH220J AA C Capacitor(50WV 22PF) [C140] 49 VCKYTV1HF104Z AA C Capacitor(50WV 0.1µF) [C141] 50 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C144] 51 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C145] 52 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C146] 53 VCKYTV1HB222K AA C Capacitor(50WV 2200PF) [C147] 54 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C148] 55 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C149] 56 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C150] 57 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C151] 58 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C152] 59 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C153] 60 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C154] 61 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C155] 62 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C156] 63 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C157] 64 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C158] 65 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C159] 66 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C160] 67 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C161] 68 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C162] 69 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C163] 70 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C164] 71 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C165] 72 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C166] 73 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C167] 74 VCKYTV1EB104K AA C Capacitor(25WV 0.1µF) [C168] 75 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C169] 76 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C170] 77 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C171] 78 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C172] 79 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C173] 80 VCKYTV1HB222K AA C Capacitor(50WV 2200PF) [C175]

NO.

PAR TS CODE

PRICE

RANK

NEW

MARK

PART

RANK

DESCRIPTION

UX-68DE FO-78DE

– 8 –

[7] Control PWB unit

81 VCCCTV1HH180J AA C Capacitor(50WV 18PF) [C176] 82 VCCCTV1HH220J AA C Capacitor(50WV 22PF) [C177] 83 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C178] 84 VCCCTV1HH220J AA C Capacitor(50WV 22PF) [C179] 85 VCCCTV1HH220J AA C Capacitor(50WV 22PF) [C180] 86 VCCCTV1HH220J AA C Capacitor(50WV 22PF) [C181] 87 VCKYTV1HB222K AA C Capacitor(50WV 2200PF) [C183] 88 VRS-TS2AD682J AA C Resistor(1/10W 6.8KΩ ±5%) [C184] 89 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C185] 90 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C186] 91 VCKYTV1EB104K AA C Capacitor(25WV 0.1µF) [C187] 92 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C188] 93 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C189] 94 VCKYTV1HB472K AA C Capacitor(50WV 4700PF) [C190] 95 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C191] 96 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C192] 97 VCCCTV1HH220J AA C Capacitor(50WV 22PF) [C193] 98 VCCCTV1HH220J AA C Capacitor(50WV 22PF) [C194]

99 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C195] 100 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C196] 101 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C197] 102 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C198] 103 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C199] 104 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C200] 105 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C201] 106 VCKYTV1EB104K AA C Resistor(25WV 0.1µF) [C202] 107 VCKYTV1HB821K AA C Capacitor(50WV 820PF) [C203] 108 VCKYTV1HB223K AA C Capacitor(50WV 0.022µF) [C204] 109 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C205] 110 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C206] 111 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C207] 112 VCCCTV1HH330J AA C Capacitor(50WV 33PF) [C208] 113 VCKYTV1HB221K AA C Capacitor(50WV 220PF) [C209] 114 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C210] 115 VCKYTV1EB104K AA C Capacitor(25WV 0.1µF) [C211] 116 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C212] 117 VRS-TS2AD000J AA C Resistor(1/10W 0Ω ±5%) [C213] 118 VCKYTV1EB104K AA C Capacitor(25WV 0.1µF) [C214] 119 VCKYTV1HB103K AB C Capacitor(50WV 0.01µF) [C215] 120 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C216] 121 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C217] 122 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C218] 123 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C219] 124 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C220] 125 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C221] 126 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C222] 127 VCKYTV1HF104Z AA C Capacitor(50WV 0.1µF) [C223] 128 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C224] 129 QCNCM7014SC0G AB C Connector(7pin) [CNCIS] 130 QCNCM2442SC0B AB C Conector(2pin) [CNCSW] 131 QCNCM705BAF06 AB C Connector(2pin) [CNDR] 132 QCNCM7014SC0B AD C Connector(2pin) [CNFRS] 133 QCNCW2500SC1B AF C Connector(12pin) [CNLIUA] 134 QCNCW2500SC0E C Connector(5pin) [CNLIUB] 135 QCNCM7014SC0F AB C Connector(6pin) [CNMT] 136 QCNCM7014SC1F AD C Connector(16pin) [CNPN] 137 QCNCW2500SC0H AF C Connector(8pin) [CNPW] 138 QCNCM2401SC0B AA C Connector(2pin) [CNSP] 139 QCNCM7014SC1F AD C Connector(16pin) [CNTH] 140 VRS-HT3AA101J AA C Resistor(1W 100Ω ±5%) [D1] 141 VHD1SS355//-1 AB B Diode(1SS355) [D2] 142 VHD1SS355//-1 AB B Diode(1SS355) [D3] 143 VHD1SS355//-1 AB B Diode(1SS355) [D4] 144 VHD1SS355//-1 AB B Diode(1SS355) [D5] 145 VHDRB705D//-1 AD B Diode(RB705D) [D6] 146 QFS-P2010SCZZ AD B IC protector(KAB2402) [FU100] 147 VHIULN2003ANS AE B IC(ULN2003A) [IC1] 148 VHITC7WT74FU1 AF B IC(TC7WT74) [IC2] 149 VHIFC2FM209V1 BK N B IC(FC200)(Within IC3 and IC5 pair) [IC3] 150 VHIKM29W040-1 AV B IC(KM29W040T) [IC4] 151 VHIFC2FM209V1 BK N B IC(FM209V)(Within IC3 and IC5 pair) [IC5] 152 VHIW24258S7LE AQ B IC(W24258S-70LE) [IC6] 153 VHIXC61AN45M1 AE B IC(XC61AN4502ML) [IC7] 154 VHITC4S66F/-1 AC B IC(TC4S66F) [IC8] 155 VHIHCF4051M1T AG B IC(HCF4051) [IC9] 156 QSOCZ0115SC32 AC C IC socket(32pin) [IC10] 157 VHI27020FPB0C BN N B IC,EPROM(2MB) [IC10] 158 VHINJM2904M-2 AG B IC(NJM2904M) [IC11] 159 VHINJM2113M-1 AG B IC(NJM2113) [IC12] 160 RCILZ2145XHZZ AF C Coil(HM601) [L100]

NO.

PAR TS CODE

PRICE

RANK

NEW

MARK

PART RANK

DESCRIPTION

UX-68DE FO-78DE

– 9 –

[7] Control PWB unit

161 RCILZ2145XHZZ AF C Coil(HM601) [L101] 162 RCILZ2145XHZZ AF C Coil(HM601) [L102] 163 RCILZ2145XHZZ AF C Coil(HM601) [L103] 164 RCILZ2145XHZZ AF C Coil(HM601) [L104] 165 RCILZ2145XHZZ AF C Coil(HM601) [L105] 166 RCILZ2145XHZZ AF C Coil(HM601) [L106] 167 VRS-TS2AD152J AA C Resistor(1/10W 1.5KΩ ±5%) [L107] 168 RCILZ2145XHZZ AF C Coil(HM601) [L108] 169 VRS-TS2AD000J AA C Resistor(1/10W 0Ω ±5%) [L110] 170 VRS-TS2AD000J AA C Resistor(1/10W 0Ω ±5%) [L111] 171 VHPSG206S//-1 AG B Photo transistor(SG206S) [PI2] 172 VSDPC114EK/-1 B Transistor(PDTC114) [Q1] 173 VS2SA1037KS-1 AB B Transistor(2SA1037KS) [Q2] 174 VS2SC2412KS-1 AB B Transistor(2SC2412-K) [Q3] 175 VS2SA1037KS-1 AB B Transistor(2SA1037KS) [Q4] 176 VSDPC114EK/-1 B Transistor(PDTC114) [Q5] 177 VSDPC114EK/-1 B Transistor(PDTC114) [Q6] 178 VSDPC114EK/-1 B Transistor(PDTC114) [Q7] 179 VRD-HT2HY222J AA C Resistor(1/2W 2.2KΩ ±5%) [R1] 180 VRD-HT2HY222J AA C Resistor(1/2W 2.2KΩ ±5%) [R2] 181 VRS-TS2AD333J AA C Resistor(1/10W 33KΩ ±5%) [R100] 182 VRS-TS2AD271J AA C Resistor(1/10W 270Ω ±5%) [R101] 183 VRS-TS2AD101J AA C Resistor(1/10W 100Ω ±5%) [R102] 184 VRS-TS2AD000J AA C Resistor(1/10W 0Ω ±5%) [R103] 185 VRS-TS2AD471J AA C Resistor(1/10W 470Ω ±5%) [R106] 186 VRS-TS2AD333J AA C Resistor(1/10W 33KΩ ±5%) [R107] 187 VRS-TS2AD333J AA C Resistor(1/10W 33KΩ ±5%) [R108] 188 VRS-TS2AD101J AA C Resistor(1/10W 100Ω ±5%) [R109] 189 VRS-TS2AD104J AA C Resistor(1/10W 100KΩ ±5%) [R110] 190 VRS-TS2AD104J AA C Resistor(1/10W 100KΩ ±5%) [R111] 191 VRS-TS2AD000J AA C Resistor(1/10W 0Ω ±5%) [R112] 192 VRS-TS2AD271J AA C Resistor(1/10W 270Ω ±5%) [R113] 193 VRS-TS2AD333J AA C Resistor(1/10W 33KΩ ±5%) [R114] 194 VRS-TS2AD471J AA C Resistor(1/10W 470Ω ±5%) [R115] 195 VRS-TS2AD151J AA C Resistor(1/10W 150Ω ±5%) [R116] 196 VRS-TS2AD471J AA C Resistor(1/10W 470Ω ±5%) [R117] 197 VRS-TS2AD333J AA C Resistor(1/10W 33KΩ ±5%) [R118] 198 VRS-TS2AD333J AA C Resistor(1/10W 33KΩ ±5%) [R119] 199 VRS-TS2AD471J AA C Resistor(1/10W 470Ω ±5%) [R120] 200 VRS-TS2AD333J AA C Resistor(1/10W 33KΩ ±5%) [R121] 201 VRS-TS2AD333J AA C Resistor(1/10W 33KΩ ±5%) [R122] 202 VRS-TS2AD101J AA C Resistor(1/10W 100Ω ±5%) [R123] 203 VRS-TS2AD333J AA C Resistor(1/10W 33KΩ ±5%) [R124] 204 VRS-TS2AD101J AA C Resistor(1/10W 100Ω ±5%) [R125] 205 VRS-TS2AD271J AA C Resistor(1/10W 270Ω ±5%) [R126] 206 VRS-TS2AD271J AA C Resistor(1/10W 270Ω ±5%) [R127] 207 VRS-TS2AD223J AA C Resistor(1/10W 22KΩ ±5%) [R128] 208 VRS-TS2AD101J AA C Resistor(1/10W 100Ω ±5%) [R129] 209 VRS-TS2AD101J AA C Resistor(1/10W 100Ω ±5%) [R130] 210 VRS-TS2AD101J AA C Resistor(1/10W 100Ω ±5%) [R131] 211 VRS-TS2AD101J AA C Resistor(1/10W 100Ω ±5%) [R132] 212 VRS-TS2AD101J AA C Resistor(1/10W 100Ω ±5%) [R133] 213 VRS-TS2AD471J AA C Resistor(1/10W 470Ω ±5%) [R134] 214 VRS-TS2AD471J AA C Resistor(1/10W 470Ω ±5%) [R135] 215 VRS-TS2AD000J AA C Resistor(1/10W 0Ω ±5%) [R136] 216 VRS-TS2AD471J AA C Resistor(1/10W 470Ω ±5%) [R137] 217 VRS-TS2AD103J AA C Resistor(1/10W 10KΩ ±5%) [R138] 218 VRS-TS2AD471J AA C Resistor(1/10W 470Ω ±5%) [R139] 219 VRS-TS2AD000J AA C Resistor(1/10W 0Ω ±5%) [R140] 220 VRS-TS2AD103J AA C Resistor(1/10W 10KΩ ±5%) [R141] 221 VRS-TS2AD333J AA C Resistor(1/10W 33KΩ ±5%) [R142] 222 VRS-TS2AD471J AA C Resistor(1/10W 470Ω ±5%) [R143] 223 VRS-TS2AD433J AA C Resistor(1/10W 43KΩ ±5%) [R144] 224 VRS-TS2AD303J AA C Resistor(1/10W 30KΩ ±5%) [R145] 225 VRS-TS2AD203J AA C Resistor(1/10W 20KΩ ±5%) [R146] 226 VRS-TS2AD333J AA C Resistor(1/10W 33KΩ ±5%) [R147] 227 VRS-TS2AD471J AA C Resistor(1/10W 470Ω ±5%) [R148] 228 VRS-TS2AD333J AA C Resistor(1/10W 33KΩ ±5%) [R149] 229 VRS-TS2AD103J AA C Resistor(1/10W 10KΩ ±5%) [R150] 230 VRS-TS2AD333J AA C Resistor(1/10W 33KΩ ±5%) [R151] 231 VRS-TS2AD103J AA C Resistor(1/10W 10KΩ ±5%) [R152] 232 VRS-TS2AD101J AA C Resistor(1/10W 100Ω ±5%) [R153] 233 VRS-TS2AD101J AA C Resistor(1/10W 100Ω ±5%) [R154] 234 VRS-TS2AD223J AA C Resistor(1/10W 22KΩ ±5%) [R156] 235 VRS-TS2AD512J AA C Resistor(1/10W 5.1KΩ ±5%) [R157] 236 VRS-TS2AD000J AA C Resistor(1/10W 0Ω ±5%) [R158] 237 VRS-TS2AD000J AA C Resistor(1/10W 0Ω ±5%) [R159] 238 VRS-TS2AD222J AA C Resistor(1/10W 2.2KΩ ±5%) [R160] 239 VRS-TS2AD3R0J AA C Resistor(1/10W 3.0Ω ±5%) [R161] 240 VRS-TS2AD102J AA C Resistor(1/10W 1.0KΩ ±5%) [R162]

NO.

PAR TS CODE

PRICE

RANK

NEW

MARK

PART

RANK

DESCRIPTION

UX-68DE FO-78DE

[7] Control PWB unit

241 VRS-TS2AD103J AA C Resistor(1/10W 10KΩ ±5%) [R163] 242 VRS-TS2AD103J AA C Resistor(1/10W 10KΩ ±5%) [R164] 243 VRS-TS2AD512J AA C Resistor(1/10W 5.1KΩ ±5%) [R165] 244 VRS-TS2AD103J AA C Resistor(1/10W 10KΩ ±5%) [R166] 245 VRS-TS2AD106J AA C Resistor(1/10W 10MΩ ±5%) [R167] 246 VRS-TS2AD105J AA C Resistor(1/10W 1.0MΩ ±5%) [R168] 247 VRS-TS2AD121J AA C Resistor(1/10W 120Ω ±5%) [R169] 248 VRS-TS2AD000J AA C Resistor(1/10W 0Ω ±5%) [R170] 249 VRS-TS2AD000J AA C Resistor(1/10W 0Ω ±5%) [R171] 250 VRS-TS2AD303J AA C Resistor(1/10W 30KΩ ±5%) [R172] 251 VRSTS2AD1183F AA C Resistor(1/10W 118KΩ ±1%) [R173] 252 VRS-TS2AD332J AA C Resistor(1/10W 3.3KΩ ±5%) [R175] 253 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [R176] 254 VRS-TS2AD000J AA C Resistor(1/10W 0Ω ±5%) [R177] 255 VRS-TS2AD123J AA C Resistor(1/10W 12KΩ ±5%) [R178] 256 VRS-TS2AD103J AA C Resistor(1/10W 10KΩ ±5%) [R179] 257 VRS-TS2AD474J AA C Resistor(1/10W 470KΩ ±5%) [R183] 258 VRS-TS2AD754J AA C Resistor(1/10W 750KΩ ±5%) [R184] 259 VRS-TS2AD304J AA C Resistor(1/10W 300KΩ ±5%) [R185] 260 VRS-TS2AD104J AA C Resistor(1/10W 100KΩ ±5%) [R186] 261 VRS-TS2AD000J AA C Resistor(1/10W 0Ω ±5%) [R187] 262 VRS-TS2AD393J AA C Resistor(1/10W 39KΩ ±5%) [R188] 263 VRS-TS2AD103J AA C Resistor(1/10W 10KΩ ±5%) [R189] 264 VRS-TS2AD102J AA C Resistor(1/10W 1.0KΩ ±5%) [R190] 265 VRS-TS2AD133J AA C Resistor(1/10W 13KΩ ±5%) [R192] 266 VRS-TS2AD513J AA C Resistor(1/10W 51KΩ ±5%) [R193] 267 VRS-TS2AD332J AA C Resistor(1/10W 3.3KΩ ±5%) [R194] 268 VRS-TS2AD101J AA C Resistor(1/10W 100Ω ±5%) [R195] 269 VRS-TS2AD473J AA C Resistor(1/10W 47KΩ ±5%) [R196] 270 VRSTS2AD1183F AA C Resistor(1/10W 118KΩ ±1%) [R197] 271 VRS-TS2AD104J AA C Resistor(1/10W 100KΩ ±5%) [R198] 272 VRS-TS2AD153J AA C Resistor(1/10W 15KΩ ±5%) [R199] 273 VRS-TS2AD104J AA C Resistor(1/10W 100KΩ ±5%) [R201] 274 VRS-TS2AD204J AA C Resistor(1/10W 200KΩ ±5%) [R202] 275 VRS-TS2AD302J AA C Resistor(1/10W 3KΩ ±5%) [R203] 276 VRS-TS2AD103J AA C Resistor(1/10W 10KΩ ±5%) [R204] 277 VRS-TS2AD203J AA C Resistor(1/10W 20KΩ ±5%) [R205] 278 VRS-TS2AD474J AA C Resistor(1/10W 470KΩ ±5%) [R208] 279 VRS-TS2AD203J AA C Resistor(1/10W 20KΩ ±5%) [R209] 280 VRS-TS2AD224J AA C Resistor(1/10W 220KΩ ±5%) [R210] 281 VRS-TS2AD562J AA C Resistor(1/10W 5.6KΩ ±5%) [R211] 282 VRS-TS2AD201J AG C Resistor(1/10W 200Ω ±5%) [R212] 283 VRS-TS2AD271J AA C Resistor(1/10W 270Ω ±5%) [R213] 284 VRS-TS2AD271J AA C Resistor(1/10W 270Ω ±5%) [R214] 285 VRS-TS2AD271J AA C Resistor(1/10W 270Ω ±5%) [R215] 286 VRS-TS2AD271J AA C Resistor(1/10W 270Ω ±5%) [R216] 287 VRS-TS2AD271J AA C Resistor(1/10W 270Ω ±5%) [R217] 288 VRS-TS2AD271J AA C Resistor(1/10W 270Ω ±5%) [R218] 289 VRS-TS2AD333J AA C Resistor(1/10W 33KΩ ±5%) [R219] 290 VRS-TS2AD333J AA C Resistor(1/10W 33KΩ ±5%) [R220] 291 VRS-TS2AD000J AA C Resistor(1/10W 0Ω ±5%) [R221] 292 RR-TZ3017SCZZ AC C Block resistor(270Ωx4) [RA1] 293 RR-TZ3018SCZZ AC C Block resistor(470Ωx4) [RA2] 294 RR-TZ3017SCZZ AC C Block resistor(270Ωx4) [RA3] 295 RR-TZ3017SCZZ AC C Block resistor(270Ωx4) [RA4] 296 RR-TZ3018SCZZ AC C Block resistor(470Ωx4) [RA5] 297 RR-TZ3017SCZZ AC C Block resistor(270Ωx4) [RA6] 298 RR-TZ3017SCZZ AC C Block resistor(270Ωx4) [RA7] 299 RR-TZ3017SCZZ AC C Block resistor(270Ωx4) [RA8] 300 RR-TZ3018SCZZ AC C Block resistor(470Ωx4) [RA9] 301 RR-TZ3018SCZZ AC C Block resistor(470Ωx4) [RA10] 302 RR-TZ3018SCZZ AC C Block resistor(470Ωx4) [RA11] 303 RR-TZ3017SCZZ AC C Block resistor(270Ωx4) [RA12] 304 RR-TZ3017SCZZ AC C Block resistor(270Ωx4) [RA13] 305 RR-TZ3018SCZZ AC C Block resistor(470Ωx4) [RA14] 306 RR-TZ3018SCZZ AC C Block resistor(470Ωx4) [RA15] 307 RR-TZ3018SCZZ AC C Block resistor(470Ωx4) [RA16] 308 VHI62FP332P-1 AF B IC(XC62FP3302P) [REQ100] 309 RRLYD3138XHZZ AG B Relay(DQ1U24VDC) [RY1] 310 RCRSQ2157SCZZ AF B Crystal(32.256MHz) [X1] 311 RCRSB0297AFZZ AD B Crystal(32.768kHz) [X2]

(Unit)

901 CPWBX3094FF01 N E Control PWB unit(Without ROM)

[8] TEL/LIU PWB unit

1 VHVRA501PV6-1 AE B Varistor(RA-501P-V6-2) [AR1]

– 10 –

NO.

PAR TS CODE

PRICE

RANK

NEW

MARK

PART RANK

DESCRIPTION

UX-68DE FO-78DE

– 11 –

[8] TEL/LIU PWB unit

2 VHVRA501PV6-1 AE B Varistor(RA-501P-V6-2) [AR2] 3 QCNW-4753XHZZ AE C Cable [ARG] 4 VCQYNA1HM474K AE C Capacitor(50WV 0.47µF) [C1] 5 RC-FZ3053FFZZ C Capacitor(250WV 1.0µF) [C2] 6 RC-FZ3055FFZZ C Capacitor(250WV 0.47µF) [C3] 7 VCEAGA1HW106M AA C Capacitor(50WV 10µF) [C4] 8 VCEAGA1HW335M AB C Capacitor(50WV 3.3µF) [C5]

9 VCEAGA1HW226M AB C Capacitor(50WV 22µF) [C6] 10 VCEAGA1HW475M AA C Capacitor(50WV 4.7µF) [C7] 11 VCEAGA1HW106M AA C Capacitor(50WV 10µF) [C8] 12 VCEAGA1HW225M AA C Capacitor(50WV 2.2µF) [C10] 13 VCEAGA1HW226M AB C Capacitor(50WV 22µF) [C11] 14 VCEAGA1EW476M AA C Capacitor(50WV 47µF) [C12] 15 VCEAGA1HW226M AB C Capacitor(50WV 22µF) [C13] 16 VCKYTV1HB103K AB C Capacitor(50WV 0.01µF) [C101] 17 VCKYTV1HB103K AB C Capacitor(50WV 0.01µF) [C102] 18 VCKYTQ1HB223K AB C Capacitor(50WV 0.022µF) [C103] 19 VCKYTQ1HB333K AA C Capacitor(50WV 0.033µF) [C104] 20 VCKYTQ1HB223K AB C Capacitor(50WV 0.022µF) [C105] 21 VCKYTV1HB473K AA C Capacitor(50WV 0.047µF) [C106] 22 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C107] 23 VCKYTV1HF104Z AA C Capacitor(50WV 0.1µF) [C109] 24 VCKYTV1HB222K AA C Capacitor(50WV 2200PF) [C110] 25 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C111] 26 VCKYTQ1HB103K AA C Capacitor(50WV 0.01µF) [C115] 27 VRS-TP2BD000J AA C Resistor(1/8W 0Ω ±5%) [C116] 28 VCKYTQ1HB563K AA C Capacitor(50WV 0.056µF) [C118] 29 VCCCTV1HH101J AA C Capacitor(50WV 100PF) [C119] 30 VCKYTV1HF104Z AA C Capacitor(50WV 0.1µF) [C120] 31 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C121] 32 VCKYTV1HF104Z AA C Capacitor(50WV 0.1µF) [C122] 33 VCKYTV1HB122K AB C Capacitor(50WV 1200PF) [C123] 34 VCKYTV1HF104Z AA C Capacitor(50WV 0.1µF) [C124] 35 VCKYTV1HF104Z AA C Capacitor(50WV 0.1µF) [C125] 36 VCKYTV1HF104Z AA C Capacitor(50WV 0.1µF) [C126] 37 VCKYTV1HB103K AB C Capacitor(50WV 0.01µF) [C127]

38 RRLYZ3427SCZZ AN B Relay [CML] 39 QJAKZ2079XH0D AD C Jack [CNHJ] 40 QCNCM2548SC1B AH C Connector(12pin) [CNLIUA] 41 QCNCM2548SC0E C Connector(5pin) [CNLIUB] 42 QJAKZ2073SCFF AE C Jack [CNLNJ] 43 QJAKZ2073SCFD AE C Jack [CNTLJ] 44 RH-DX0045BMZZ B Diode(1N4148) [D1] 45 RH-DX0045BMZZ B Diode(1N4148) [D2] 46 RH-DX0045BMZZ B Diode(1N4148) [D3] 47 RH-DX0045BMZZ B Diode(1N4148) [D4] 48 QSW-Z2263XHZZ AG B Hook switch [HOOK SW] 49 VHILMT2904DR2 B IC(LMT2904DR) [IC101] 50 VHILMT2904DR2 B IC(LMT2904DR) [IC102] 51 RFILN2027XHZZ AC C Coil(R-5C) [L2A] 52 RFILN2027XHZZ AC C Coil(R-5C) [L2B] 53 RCILF2125SCZZ AD C Coil(4.7mH) [L3] 54 RCILF2125SCZZ AD C Coil(4.7mH) [L5]

55 RFILN2027XHZZ AC C Coil(R-5C) [L6]

56 RFILN2027XHZZ AC C Coil(R-5C) [L7]

57 RFILN2027XHZZ AC C Coil(R-5C) [L8]

58 VHPTLP627//-1 AH B Photo coupler(TLP627) [PC2]

59 VHPTLP627//-1 AH B Photo coupler(TLP627) [PC3]

60 VHPTLP521-1BL AE B Photo coupler(TLP521) [PC5]

61 VHPTLP521-1BL AE B Photo coupler(TLP521) [PC6] 62 VS2SA1807-P-1 AE B Transistor(2SA1807) [Q1] 63 VS2N5401///-1 B Transistor(2N5401) [Q2] 64 VSBS108////-1 AE B FET(BS108) [Q3] 65 VSBC847B///-1 B Transistor(BC847B) [Q101] 66 VSDPC114EK/-1 B Transistor(PDTC114) [Q102] 67 VSDPC114EK/-1 B Transistor(PDTC114) [Q106] 68 VSDPC114EK/-1 B Transistor(PDTC114) [Q108] 69 VSDPC114EK/-1 B Transistor(PDTC114) [Q110] 70 VRD-HT2HY473J AA C Resistor(1/2W 47KΩ ±5%) [R2] 71 VRS-HT3LA821J C Resistor(3W 820Ω ±5%) [R3] 72 VRS-TS2AD161J AA C Resistor(1/10W 160Ω ±5%) [R101] 73 VRS-TS2AD124J AA C Resistor(1/10W 120KΩ ±5%) [R102] 74 VRS-TS2AD103J AA C Resistor(1/10W 10KΩ ±5%) [R103] 75 VRS-TP2BD120J C Resistor(1/8W 12Ω ±5%) [R104] 76 VRS-TS2AD474J AA C Resistor(1/10W 470KΩ ±5%) [R105] 77 VRS-TS2AD203J AA C Resistor(1/10W 20KΩ ±5%) [R107] 78 VRS-TP2BD560J AA C Resistor(1/8W 56 Ω ±5%) [R108] 79 VRS-TS2AD000J AA C Resistor(1/10W 0 Ω ±5%) [R109] 80 VRS-TP2BD150J AA C Resistor(1/8W 15 Ω ±5%) [R110] 81 VRS-TS2AD103J AA C Resistor(1/10W 10KΩ ±5%) [R111]

NO.

PAR TS CODE

PRICE

RANK

NEW

MARK

PART

RANK

DESCRIPTION

UX-68DE FO-78DE

– 12 –

[8] TEL/LIU PWB unit

82 VRS-TP2BD470J AA C Resistor(1/8W 47 Ω ±5%) [R112] 83 VRS-TS2AD152J AA C Resistor(1/10W 1.5KΩ ±5%) [R114] 84 VRS-TS2AD102J AA C Resistor(1/10W 1KΩ ±5%) [R115] 85 VRS-TS2AD103J AA C Resistor(1/10W 10KΩ ±5%) [R116] 86 VRS-TS2AD163J AA C Resistor(1/10W 16KΩ ±5%) [R117] 87 VRS-TS2AD203J AA C Resistor(1/10W 20KΩ ±5%) [R118] 88 VRS-TS2AD151J AA C Resistor(1/10W 150Ω ±5%) [R119] 89 VRS-TS2AD102J AA C Resistor(1/10W 1KΩ ±5%) [R120] 90 VRS-TS2AD303J AA C Resistor(1/10W 30KΩ ±5%) [R121] 91 VRS-TS2AD103J AA C Resistor(1/10W 10KΩ ±5%) [R122] 92 VRS-TS2AD332J AA C Resistor(1/10W 3.3KΩ ±5%) [R123] 93 VRS-TS2AD473J AA C Resistor(1/10W 47KΩ ±5%) [R124] 94 VRS-TS2AD243J AA C Resistor(1/10W 24KΩ ±5%) [R125] 95 VRS-TS2AD102J AA C Resistor(1/10W 1KΩ ±5%) [R126] 96 VRS-TS2AD822J AA C Resistor(1/10W 8.2KΩ ±5%) [R128] 97 VRS-TS2AD332J AA C Resistor(1/10W 3.3KΩ ±5%) [R129] 98 VRS-TS2AD222J AA C Resistor(1/10W 2.2KΩ ±5%) [R131]

99 VRS-TS2AD391J AA C Resistor(1/10W 390Ω ±5%) [R133] 100 VRS-TS2AD000J AA C Resistor(1/10W 0Ω ±5%) [R134] 101 VRS-TS2AD223J AA C Resistor(1/10W 22KΩ ±5%) [R135] 102 VRS-TS2AD332J AA C Resistor(1/10W 3.3KΩ ±5%) [R136] 103 VRS-TS2AD751J AA C Resistor(1/10W 750Ω ±5%) [R137] 104 VRS-TS2AD244J AA C Resistor(1/10W 240KΩ ±5%) [R138] 105 VRS-TS2AD102J AA C Resistor(1/10W 1KΩ ±5%) [R139] 106 VRS-TS2AD223J AA C Resistor(1/10W 22KΩ ±5%) [R140] 107 VRS-TS2AD303J AA C Resistor(1/10W 30KΩ ±5%) [R141] 108 VRS-TS2AD332J AA C Resistor(1/10W 3.3KΩ ±5%) [R142] 109 VRS-TS2AD103J AA C Resistor(1/10W 10KΩ ±5%) [R143] 110 VRS-TS2AD303J AA C Resistor(1/10W 30KΩ ±5%) [R144] 111 VRS-TS2AD102J AA C Resistor(1/10W 1KΩ ±5%) [R145] 112 VRS-TS2AD102J AA C Resistor(1/10W 1KΩ ±5%) [R147] 113 VRS-TS2AD471J AA C Resistor(1/10W 470Ω ±5%) [R148] 114 VRS-TS2AD471J AA C Resistor(1/10W 470Ω ±5%) [R149] 115 VRS-TS2AD104J AA C Resistor(1/10W 100KΩ ±5%) [R152] 116 VRS-TS2AD104J AA C Resistor(1/10W 100KΩ ±5%) [R153] 117 VHDS1ZB60//-1 AC B Diode bridge(S1ZB60) [REC1]

118 RTRNI2165XHZZ AG B Transformer [T1]

119 VHVDSS301L/-U AF B Varistor(DSS-301L) [VA1] 120 VHVSIOVS05K60 B Varistor(SIOV-S05K60T) [VA2] 121 VHEBZX79B20/A AC B Zener diode(BZX79B20V) [ZD1] 122 VHEBZX79B6V8A B Zener diode(BZX79B6V8) [ZD2] 123 VHEBZX79B20/A AC B Zener diode(BZX79B20V) [ZD3] 124 VHEBZX79B3V3A B Zener diode(BZX79B3V3) [ZD6] 125 VHEBZX79B3V3A B Zener diode(BZX79B3V3) [ZD7]

(Unit)

901 DCEKL227CFF01 E TEL/Liu PWB unit

[9] Power supply PWB unit

1 0CBUGFM224KR/ AF C Capacitor(RE224-C) [C1] 2 0CBUGZ1072ZZ/ AN C Capacitor(KMF400VB68M) [C2] 3 0CBUGCV102HZ/ AD C Capacitor(ECKZ3D102KBP) [C3] 4 0CBUGXAEF222/ AC C Capacitor(GRM40B222K50PT) [C4] 5 0CBUEXCAO000/ AB C Resistor(MCR10EZHJ000) [C6] 6 0CBUGCM392BJ/ AF C Capacitor(DE1510-1E392M-KX) [C7] 7 0CBUGAE561TS/ AH C Capacitor(LXJ35VB560(M)) [C8] 8 0CBUGFF474JA/ AF C Capacitor(ECQV1H474JL3) [C9]

9 0CBUGAC222VV/ AK C Capacitor(LXZ16VB2200(K)) [C10] 10 0CBUGXAED104/ AC C Capacitor(GRM40B104K25PT) [C12] 11 0CBUGZ1041ZZ/ AF C Capacitor(DE1007E222M-KH) [C15] 12 0CBUGAB101RV/ AF C Capacitor(KME10VB100(M)) [C16] 13 0CBUGXAEF102/ AC C Capacitor(GRM40B102K50PT) [C17] 14 0CBUGCU681BR/ AC C Capacitor(DEO805R681K1K-MHR) [C21] 15 0CBUGFF223EH/ AC C Capacitor(AMZV-223J50) [C24] 16 0CBPKZ0194ZZ/ AC C Base post ass’y(B 2P3-VH) [CN1] 17 0CBPCZ0275ZZ/ AD C Connector(8PL-FJ) [CN2] 18 0CBUBC0125DK/ AD B Diode(ERA15-06) [D1] 19 0CBUBC0125DK/ AD B Diode(ERA15-06) [D2] 20 0CBUBC0125DK/ AD B Diode(ERA15-06) [D3] 21 0CBUBC0125DK/ AD B Diode(ERA15-06) [D4] 22 0CBUBY0020AK/ AD B Diode(1SS355) [D5] 23 0CBUBC0336AZ/ AL B Diode(S3L20U-4004P15) [D7] 24 0CBUBC0302BZ/ AE B Diode(SR140) [D8] 25 0CBPJCEJ1601/ AH A Current fuse(21501.6 ME600) [F1] 26 0CBPJCEJ1601/ AH A Current fuse(21501.6 ME600) [F2] 27 0CBPZZ0906ZZ/ AH A Circuit protect chip(CCP2E100) [F3] 28 0CBBFZ89256Z/ AD B Beads core(BL02RNI-R62T4) [FB1]

NO.

PAR TS CODE

PRICE

RANK

NEW

MARK

PART RANK

DESCRIPTION

UX-68DE FO-78DE

[9] Power supply PWB unit

29 0CBUCB0199AZ/ AR B IC(UPC29M05AHF) [IC1] 30 0CBUKZ0826ZZ/ AK C Filter(ELF15N003A) [L1] 31 0CBUZZ0156ZZ/ AN C Coil(RS208) [L2] 32 0CBPZZ0940ZZ/ AB C Jumper(J1/6Z-T26-A) [L3] 33 0CBLRZ6616ZN/ AQ C Heat sink(MN903-5001AT) [MT1] 34 0CBLRZ6619ZQ/ AQ C Heat sink(MF903-5002AT) [MT2] 35 0CBUDC0163CZ/ AG B Photo coupler(PC123YS) [PC1] 36 0CBUDC0163CZ/ AG B Photo coupler(PC123YS) [PC2] 37 0CBUAG0161AC/ AQ B FET(FS5KM-18A-AN) [Q1] 38 0CBUDA0128AK/ AD B Transistor(2SD2114K) [Q2] 39 0CBUAY0016CK/ AD B Transistor(2SC2412K) [Q3] 40 0CBUAY0016CK/ AD B Transistor(2SC2412K) [Q4] 41 0CBUAC0289AK/ AD B Transistor(2SC4210) [Q5] 42 0CBUAC0289AK/ AD B Transistor(2SC4210) [Q6] 43 0CBUEEC335CH/ AC C Resistor(RDM12TB335J) [R1] 44 0CBUEEC105CH/ AC C Resistor(RDM12TB105J) [R2] 45 0CBUEEC105CH/ AC C Resistor(RDM12TB105J) [R3] 46 0CBUEXCAS331/ AB C Resistor(CR21TR331J) [R4] 47 0CBUEXCAS152/ AB C Resistor(CR21TR152J) [R5] 48 0CBUEXCAS183/ AB C Resistor(CR21TR183J) [R6] 49 0CBUEXCAS330/ AB C Resistor(CR21TR330J) [R7] 50 0CBUEXCAS473/ AB C Resistor(CR21TR473J) [R8] 51 0CBUEXCAS471/ AB C Resistor(CR21TR471J) [R9] 52 0CBUEFDR33DB/ AE C Resistor(RSMF1TBR33G) [R10] 53 0CBUEXCAS390/ AB C Resistor(CR21TR390J) [R11] 54 0CBUEXCAS184/ AB C Resistor(CR21TR184J) [R12] 55 0CBUEXCAS472/ AB C Resistor(CR21TR472J) [R13] 56 0CBUEXCAS152/ AB C Resistor(CR21TR152J) [R14] 57 0CBUEXCAS334/ AB C Resistor(CR21TR334J) [R15] 58 0CBUEXCAS223/ AB C Resistor(CR21TR223J) [R16] 59 0CBUEXCAS822/ AB C Resistor(CR21TR822J) [R17] 60 0CBUEXCAS273/ AB C Resistor(CR21TR273J) [R18] 61 0CBUEXCAS472/ AB C Resistor(CR21TR472J) [R19] 62 0CBUEXCAS472/ AB C Resistor(CR21TR472J) [R20] 63 0CBUEXCAS154/ AB C Resistor(CR21TR154J) [R21] 64 0CBUEXCAS103/ AB C Resistor(CR21TR103J) [R25] 65 0CB829655027/ BE B Transformer(PTTP124-KTT) [T1] 66 0CBUDC0232AK/ AF B Thermistor(KL07L8R2TB) [TH1] 67 0CBUEZ0507ZZ/ AD B Varistor(ERZV07D471) [V1] 68 0CBUFBA102FE/ AD B Variable resistor(ENV CYA A01 B13) [VR1] 69 0CBUBDAX270A/ AD B Zener diode(RD27SB) [ZD1] 70 0CBUBXAD2R0A/ AD B Zener diode(RD2.0SB) [ZD2] 71 0CBUBDBM300D/ AC B Zener diode(RD30FB) [ZD4] 72 0CBUBXAD6R2C/ AD B Zener diode(RD6.2SB) [ZD5] 73 0CBUBDBE200D/ AD B Zener diode(RD20ESAB) [ZD7]

(Unit)

901 RDENT2144XHZZ BA E Power supply PWB unit

– 13 –

No.

NEW

MARK

PART RANK

PRICE

RANK

PARTS CODE

No.

NEW MARK

PART

RANK

PRICE

RANK

PARTS CODE

No.

NEW

MARK

PART RANK

PRICE

RANK

PARTS CODE

UX-68DE FO-78DE

– 14 –

I n d e x

[C]

CCNW-212AXH01 1-2 AK C

″ 3-1 AK C CCNW-215AFF01 1-12 C CPWBX3094FF01 1-45 N E

″ 7-901 N E

[D]

DCEKK201CFF10 1-1 N E

″ 3-901 N E DCEKK201CFF11 1-1 N E

″ 3-901 N E DCEKL227CFF01 1-16 E

″ 8-901 E DCEKP203CFF02 3-7 N E DUNTK204CFFBG 6-2 E DUNTK204CFFWH 6-2 E

[G] GCABA2342FFSX 3-3 N D GCABA2342FFSY 3-3 N D GCABB2343FFSA 1-13 D GCABB2343FFSC 1-13 D GCASP2110FFSD 1-17 N C GCASP2110FFSE 1-17 N C GCASP2111FFSA 1-18 N C GCASP2111FFSC 1-18 N C GDAI-2082XHSA 1-46 AD C GDAI-2082XHSC 1-46 C GDAI-2083FFZZ 1-22 C

[H] HPNLH2393XHSJ 1-54 N D HPNLH2393XHSP 1-54 N D

[J] JBTN-2257FFSA 3-4 C JBTN-2257FFSC 3-4 C JBTN-2258FFSA 3-5 C JBTN-2258FFSC 3-5 C JBTN-2261FFSA 3-6 C JBTN-2261FFSC 3-6 C JBTN-2262FFSA 3-8 N C JBTN-2262FFSC 3-8 N C

[L] LBSHP2110XHZZ 2-1 AB C LBSHP2112XHZZ 1-28 AB C LFRM-2207XHZZ 5-1 AF C LFRM-2208XHZZ 1-29 AF N C LFRM-2209FFZZ 2-2 C LHLDW1033CE00 1-55 AA C

″ 2-19 AA C LHLDZ2180XHZZ 2-3 AC C LHLDZ2181XHZZ 2-4 AC C LHLDZ2184XHZZ 1-30 AC C LHLDZ2185XHZZ 1-31 AC C LPLTG2911XHZZ 4-1 AE C LPLTM3049XHZZ 5-2 AD C LPLTM3107XHZZ 1-56 AD N C LPLTP2908XHZZ 4-2 AE C LPLTP3051XHZZ 4-3 AB C LSTPP2054XHZZ 1-47 AC C LX-BZ2138FFZZ 1-B1 C

[M] MCAMP2027XHZZ 5-4 AC C MLEVP2311XHZZ 5-5 AB C MLEVP2312XHZZ 5-6 AB C MLEVP2314XHZZ 5-8 AB C MLEVP2316XHZZ 1-23 AC C MLEVP2317XHZZ 2-5 AB C MLEVP2319XHZZ 1-49 AC C MLEVP2320XHZZ 1-19 AC C MLEVP2321XHZZ 1-58 AN C MSPRC2735XHZZ 5-9 AC C MSPRC2954FFZZ 1-5 C MSPRC3110XHZZ 5-10 AB C MSPRC3112FFZZ 1-33 C MSPRC3117FFZZ 2-6 C MSPRC3148FFZZ 1-34 C MSPRD3116FFZZ 1-24 C MSPRP3119XHZZ 1-14 AC C MSPRP3123XHZZ 1-15 AC C MSPRT3139FFZZ 4-5 C MSPRT3140FFZZ 4-4 C

[N] NGERH2278XHZZ 5-12 AC C NGERH2379XHZZ 5-13 AC C NGERH2391XHZZ 5-15 AC C NGERH2475XHZZ 5-17 AB C NGERH2478XHZZ 1-36 AB C NGERH2479XHZZ 2-7 AB C NGERH2480XHZZ 2-8 AB C NGERH2481XHZZ 2-9 AB C NGERP2318XHZZ 1-6 AD C NROLR2375XHZZ 2-10 AL C NROLR2425XHZZ 1-37 AP C NROLR2428XHZZ 2-11 AP C NSFTZ2273XHZZ 2-12 AF C

[P] PGIDM2554FFZZ 4-6 C PGIDM2560XHSA 1-7 AC C PGIDM2560XHSC 1-7 C PGIDM2561XHSA 1-8 AC C PGIDM2561XHSC 1-8 C PGIDM2562XHZZ 2-13 AD C PGIDM2563XHSA 1-27 AE C PGIDM2563XHSC 1-27 AC C PGIDM2566XHZZ 1-52 AC C PGIDM2578XHZZ 6-16 AE C PGIDM2579XHZZ 6-17 AE C PHOP-2104FFSA 1-9 C PHOP-2104FFSC 1-9 C PHOP-2105XHZZ 6-4 AD C PSHEZ3410FFZZ 1-57 N C PSHEZ3517FFZZ 4-7 C PSHEZ3543XHZZ 2-21 AE N C

[Q] QACCE2013BMZZ 1-20 B QCNCM2401SC0B 7-138 AA C QCNCM2442SC0B 7-130 AB C QCNCM2548SC0E 8-41 C QCNCM2548SC1B 8-40 AH C QCNCM7014SC0B 7-132 AD C QCNCM7014SC0F 7-135 AB C QCNCM7014SC0G 7-129 AB C QCNCM7014SC1F 7-136 AD C

″ 7-139 AD C QCNCM705BAF06 7-131 AB C QCNCW2500SC0E 7-134 C QCNCW2500SC0H 7-137 AF C QCNCW2500SC1B 7-133 AF C QCNW-209AXHZZ 1-39 AH C QCNW-210AXHZZ 1-40 AC C QCNW-213AXHZZ 2-16 AC C QCNW-352AFFZZ 2-22 N C QCNW-3976XHBG 6-3 AK C QCNW-3976XHOW 6-3 AK C QCNW-4649FFZZ 6-5 C QCNW-4753XHZZ 8-3 AE C QCNW-4814XHZZ 2-15 AG C QCNW-4933XHZZ 5-20 AC C QFS-P2010SCZZ 7-146 AD B QJAKZ2073SCFD 8-43 AE C QJAKZ2073SCFF 8-42 AE C QJAKZ2079XH0D 8-39 AD C QSOCZ0115SC32 7-156 AC C QSW-F2224SCZZ 5-21 AE B QSW-M2293XHZZ 2-17 AE B QSW-M2296XHZZ 1-11 AD B QSW-Z2263XHZZ 8-48 AG B

[R] RC-FZ3053FFZZ 8-5 C RC-FZ3055FFZZ 8-6 C RCILF2125SCZZ 8-53 AD C

″ 8-54 AD C

RCILZ2145XHZZ 7-160 AF C

″ 7-161 AF C ″ 7-162 AF C ″ 7-163 AF C ″ 7-164 AF C ″ 7-165 AF C ″ 7-166 AF C ″ 7-168 AF C

RCORF2063XHZZ 2-20 AF B

RCORF2064XHZZ 1-53 AF B RCRSB0297AFZZ 7-311 AD B RCRSQ2157SCZZ 7-310 AF B RDENT2144XHZZ 1-21 BA E

″ 9-901 BA E

RFILN2027XHZZ 8-51 AC C

″ 8-52 AC C ″ 8-55 AC C ″ 8-56 AC C ″ 8-57 AC C

RH-DX0045BMZZ 8-44 B

″ 8-45 B ″ 8-46 B ″ 8-47 B

RHEDZ2059XHZZ 1-41 BF B RMOTZ2148XHZZ 5-22 AT B RR-TZ3017SCZZ 7-292 AC C

″ 7-294 AC C ″ 7-295 AC C ″ 7-297 AC C ″ 7-298 AC C ″ 7-299 AC C ″ 7-303 AC C ″ 7-304 AC C

RR-TZ3018SCZZ 7-293 AC C

″ 7-296 AC C ″ 7-300 AC C ″ 7-301 AC C ″ 7-302 AC C ″ 7-305 AC C ″ 7-306 AC C ″ 7-307 AC C

RRLYD3138XHZZ 7-309 AG B RRLYZ3427SCZZ 8-38 AN B RTRNI2165XHZZ 8-118 AG B RUNTZ2054XHZZ 2-18 BE B

[S] SPAKA287BFFZZ 6-7 D SPAKA288BFFZZ 6-8 D SPAKA289BFFZZ 6-9 D SPAKC168BFFZZ 6-10 D SPAKP3385FFZZ 6-6 D

[T] TINSG4052FFZZ 6-1 N D TINSG4053FFZZ 6-1 N D TLABM363BFFZZ 6-26 N D TLABM433AFFZZ 6-11 N D TPAPK2205FFZZ 6-27 N S

[U]

UBATL2046SCZZ 7-1 AK B

[V] VCCCTV1HH100D 7-16 AA C

″ 7-17 AA C VCCCTV1HH101J 8-29 AA C VCCCTV1HH180J 7-81 AA C VCCCTV1HH220J 7-47 AA C

″ 7-48 AA C

″ 7-82 AA C

″ 7-84 AA C

″ 7-85 AA C

″ 7-86 AA C

″ 7-97 AA C

″ 7-98 AA C

VCCCTV1HH330J 7-112 AA C VCCCTV1HH680J 7-43 AA C

″ 7-44 AA C VCEAGA1EW476M 7-3 AA C

″ 7-5 AA C

″ 7-6 AA C

″ 7-10 AA C

″ 8-14 AA C

VCEAGA1HW106M 7-2 AA C

″ 7-4 AA C

″ 7-8 AA C

″ 8-7 AA C

″ 8-11 AA C

VCEAGA1HW107M 7-7 AA C VCEAGA1HW225M 8-12 AA C VCEAGA1HW226M 7-9 AB C

″ 8-9 AB C

No.

NEW

MARK

PART

RANK

PRICE

RANK

PARTS CODE

No.

NEW

MARK

PART RANK

PRICE

RANK

PARTS CODE

No.

NEW

MARK

PART RANK

PRICE

RANK

PARTS CODE

UX-68DE FO-78DE

– 15 –

VCEAGA1HW226M 8-13 AB C

″ 8-15 AB C VCEAGA1HW335M 8-8 AB C VCEAGA1HW475M 8-10 AA C VCKYTQ1HB103K 8-26 AA C VCKYTQ1HB223K 8-18 AB C

″ 8-20 AB C VCKYTQ1HB333K 8-19 AA C VCKYTQ1HB563K 8-28 AA C VCKYTV1CF105Z 7-22 AB C

″ 7-26 AB C

″ 7-27 AB C

″ 7-33 AB C

″ 7-34 AB C

″ 7-36 AB C

″ 7-37 AB C

″ 7-39 AB C

″ 7-42 AB C

″ 7-52 AB C

″ 7-54 AB C

″ 7-55 AB C

″ 7-56 AB C

″ 7-58 AB C

″ 7-59 AB C

″ 7-60 AB C

″ 7-63 AB C

″ 7-66 AB C

″ 7-69 AB C

″ 7-71 AB C

″ 7-75 AB C

″ 7-77 AB C

″ 7-78 AB C

″ 7-83 AB C

″ 7-89 AB C

″ 7-90 AB C

″ 7-93 AB C

″ 7-95 AB C

″ 7-99 AB C

″ 7-105 AB C

″ 7-111 AB C

″ 7-114 AB C

″ 7-116 AB C

″ 7-253 AB C

VCKYTV1EB104K 7-74 AA C

″ 7-91 AA C

″ 7-106 AA C

″ 7-115 AA C

″ 7-118 AA C

VCKYTV1EF104Z 7-23 AA C

″ 7-24 AA C

″ 7-30 AA C

″ 7-35 AA C

″ 7-45 AA C

″ 7-50 AA C

″ 7-51 AA C

″ 7-61 AA C

″ 7-67 AA C

″ 7-72 AA C

″ 7-73 AA C

″ 7-76 AA C

″ 7-79 AA C

″ 7-92 AA C

″ 7-96 AA C

″ 7-120 AA C

″ 7-128 AA C

VCKYTV1HB102K 7-11 AA C

″ 7-12 AA C

″ 7-13 AA C

″ 7-14 AA C

″ 7-15 AA C

″ 7-18 AA C

″ 7-19 AA C

″ 7-20 AA C

″ 7-21 AA C

″ 7-25 AA C

″ 7-28 AA C

″ 7-29 AA C

″ 7-40 AA C

″ 7-41 AA C

″ 7-46 AA C

VCKYTV1HB102K 7-57 AA C

″ 7-62 AA C ″ 7-64 AA C ″ 7-65 AA C ″ 7-68 AA C ″ 7-70 AA C ″ 7-100 AA C ″ 7-101 AA C ″ 7-102 AA C ″ 7-103 AA C ″ 7-104 AA C ″ 7-109 AA C ″ 7-110 AA C ″ 7-121 AA C ″ 7-122 AA C ″ 7-123 AA C ″ 7-124 AA C ″ 7-125 AA C ″ 7-126 AA C ″ 8-22 AA C ″ 8-25 AA C ″ 8-31 AA C

VCKYTV1HB103K 7-38 AB C

″ 7-119 AB C ″ 8-16 AB C ″ 8-17 AB C ″ 8-37 AB C

VCKYTV1HB122K 8-33 AB C VCKYTV1HB221K 7-113 AA C VCKYTV1HB222K 7-31 AA C

″ 7-32 AA C ″ 7-53 AA C ″ 7-80 AA C ″ 7-87 AA C ″ 8-24 AA C

VCKYTV1HB223K 7-108 AA C VCKYTV1HB472K 7-94 AA C VCKYTV1HB473K 8-21 AA C VCKYTV1HB821K 7-107 AA C VCKYTV1HF104Z 7-49 AA C

″ 7-127 AA C ″ 8-23 AA C ″ 8-30 AA C ″ 8-32 AA C ″ 8-34 AA C ″ 8-35 AA C ″ 8-36 AA C

VCQYNA1HM474K 8-4 AE C VHDRB705D//-1 7-145 AD B VHDS1ZB60//-1 8-117 AC B VHD1SS355//-1 7-141 AB B

″ 7-142 AB B ″ 7-143 AB B ″ 7-144 AB B

VHEBZX79B20/A 8-121 AC B

″ 8-123 AC B

VHEBZX79B3V3A 8-124 B

″ 8-125 B VHEBZX79B6V8A 8-122 B VHIFC2FM209V1 7-149 BK N B

″ 7-151 BK N B VHIHCF4051M1T 7-155 AG B VHIKM29W040-1 7-150 AV B VHILMT2904DR2 8-49 B

″ 8-50 B VHINJM2113M-1 7-159 AG B VHINJM2904M-2 7-158 AG B VHITC4S66F/-1 7-154 AC B VHITC7WT74FU1 7-148 AF B VHIULN2003ANS 7-147 AE B VHIW24258S7LE 7-152 AQ B VHIXC61AN45M1 7-153 AE B VHI27020FPB0C 7-157 BN N B VHI62FP332P-1 7-308 AF B VHPSG206S//-1 7-171 AG B VHPTLP521-1BL 8-60 AE B

″ 8-61 AE B VHPTLP627//-1 8-58 AH B

″ 8-59 AH B VHVDSS301L/-U 8-119 AF B

VHVRA501PV6-1 8-1 AE B

″ 8-2 AE B VHVSIOVS05K60 8-120 B VRD-HT2HY222J 7-179 AA C

″ 7-180 AA C VRD-HT2HY473J 8-70 AA C VRS-HT3AA101J 7-140 AA C VRS-HT3LA821J 8-71 C VRS-TP2BD000J 8-27 AA C VRS-TP2BD120J 8-75 C VRS-TP2BD150J 8-80 AA C VRS-TP2BD470J 8-82 AA C VRS-TP2BD560J 8-78 AA C VRS-TS2AD000J 7-117 AA C

″ 7-169 AA C

″ 7-170 AA C

″ 7-184 AA C

″ 7-191 AA C

″ 7-215 AA C

″ 7-219 AA C

″ 7-236 AA C

″ 7-237 AA C

″ 7-248 AA C

″ 7-249 AA C

″ 7-254 AA C

″ 7-261 AA C

″ 7-291 AA C

″ 8-79 AA C

″ 8-100 AA C

VRS-TS2AD101J 7-183 AA C

″ 7-188 AA C

″ 7-202 AA C

″ 7-204 AA C

″ 7-208 AA C

″ 7-209 AA C

″ 7-210 AA C

″ 7-211 AA C

″ 7-212 AA C

″ 7-232 AA C

″ 7-233 AA C

″ 7-268 AA C

VRS-TS2AD102J 7-240 AA C

″ 7-264 AA C

″ 8-84 AA C

″ 8-89 AA C

″ 8-95 AA C

″ 8-105 AA C

″ 8-111 AA C

″ 8-112 AA C

VRS-TS2AD103J 7-217 AA C

″ 7-220 AA C

″ 7-229 AA C

″ 7-231 AA C

″ 7-241 AA C

″ 7-242 AA C

″ 7-244 AA C

″ 7-256 AA C

″ 7-263 AA C

″ 7-276 AA C

″ 8-74 AA C

″ 8-81 AA C

″ 8-85 AA C

″ 8-91 AA C

″ 8-109 AA C

VRS-TS2AD104J 7-189 AA C

″ 7-190 AA C

″ 7-260 AA C

″ 7-271 AA C

″ 7-273 AA C

″ 8-115 AA C

″ 8-116 AA C

VRS-TS2AD105J 7-246 AA C VRS-TS2AD106J 7-245 AA C VRS-TS2AD121J 7-247 AA C VRS-TS2AD123J 7-255 AA C VRS-TS2AD124J 8-73 AA C VRS-TS2AD133J 7-265 AA C VRS-TS2AD151J 7-195 AA C

″ 8-88 AA C VRS-TS2AD152J 7-167 AA C

No.

NEW

MARK

PART RANK

PRICE

RANK

PARTS CODE

No.

NEW MARK

PART

RANK

PRICE

RANK

PARTS CODE

No.

NEW

MARK

PART RANK

PRICE

RANK

PARTS CODE

UX-68DE FO-78DE

– 16 –

VRS-TS2AD152J 8-83 AA C VRS-TS2AD153J 7-272 AA C VRS-TS2AD161J 8-72 AA C VRS-TS2AD163J 8-86 AA C VRS-TS2AD201J 7-282 AG C VRS-TS2AD203J 7-225 AA C

″ 7-277 AA C ″ 7-279 AA C ″ 8-77 AA C ″ 8-87 AA C

VRS-TS2AD204J 7-274 AA C VRS-TS2AD222J 7-238 AA C

″ 8-98 AA C

VRS-TS2AD223J 7-207 AA C

″ 7-234 AA C ″ 8-101 AA C ″ 8-106 AA C

VRS-TS2AD224J 7-280 AA C VRS-TS2AD243J 8-94 AA C VRS-TS2AD244J 8-104 AA C VRS-TS2AD271J 7-182 AA C

″ 7-192 AA C ″ 7-205 AA C ″ 7-206 AA C ″ 7-283 AA C ″ 7-284 AA C ″ 7-285 AA C ″ 7-286 AA C ″ 7-287 AA C ″ 7-288 AA C

VRS-TS2AD3R0J 7-239 AA C VRS-TS2AD302J 7-275 AA C VRS-TS2AD303J 7-224 AA C

″ 7-250 AA C ″ 8-90 AA C ″ 8-107 AA C ″ 8-110 AA C

VRS-TS2AD304J 7-259 AA C VRS-TS2AD332J 7-252 AA C

″ 7-267 AA C ″ 8-92 AA C ″ 8-97 AA C ″ 8-102 AA C ″ 8-108 AA C

VRS-TS2AD333J 7-181 AA C

″ 7-186 AA C ″ 7-187 AA C ″ 7-193 AA C ″ 7-197 AA C ″ 7-198 AA C ″ 7-200 AA C ″ 7-201 AA C ″ 7-203 AA C ″ 7-221 AA C ″ 7-226 AA C ″ 7-228 AA C ″ 7-230 AA C ″ 7-289 AA C ″ 7-290 AA C

VRS-TS2AD391J 8-99 AA C VRS-TS2AD393J 7-262 AA C VRS-TS2AD433J 7-223 AA C VRS-TS2AD471J 7-185 AA C

″ 7-194 AA C ″ 7-196 AA C ″ 7-199 AA C ″ 7-213 AA C ″ 7-214 AA C ″ 7-216 AA C ″ 7-218 AA C ″ 7-222 AA C ″ 7-227 AA C ″ 8-113 AA C ″ 8-114 AA C

VRS-TS2AD473J 7-269 AA C

″ 8-93 AA C

VRS-TS2AD474J 7-257 AA C

″ 7-278 AA C ″ 8-76 AA C

VRS-TS2AD512J 7-235 AA C

VRS-TS2AD512J 7-243 AA C VRS-TS2AD513J 7-266 AA C VRS-TS2AD562J 7-281 AA C VRS-TS2AD682J 7-88 AA C VRS-TS2AD751J 8-103 AA C VRS-TS2AD754J 7-258 AA C VRS-TS2AD822J 8-96 AA C VRSTS2AD1183F 7-251 AA C

″ 7-270 AA C VSBC847B///-1 8-65 B VSBS108////-1 8-64 AE B VSDPC114EK/-1 7-172 B

″ 7-176 B

″ 7-177 B

″ 7-178 B

″ 8-66 B

″ 8-67 B

″ 8-68 B

″ 8-69 B

VS2N5401///-1 8-63 B VS2SA1037KS-1 7-173 AB B

″ 7-175 AB B VS2SA1807-P-1 8-62 AE B VS2SC2412KS-1 7-174 AB B

[X] XBBSD30P06000 1-B4 AA C XBPSN40P06K00 1-B5 AA C XEBSD30P08000 1-B3 AA C

″ 5-B3 AA C XEBSD30P12000 1-B7 AA C XUBSD20P06000 3-B2 AA C

[0] 0CBBFZ89256Z/ 9-28 AD B 0CBLRZ6616ZN/ 9-33 AQ C 0CBLRZ6619ZQ/ 9-34 AQ C 0CBPCZ0275ZZ/ 9-17 AD C 0CBPJCEJ1601/ 9-25 AH A

″ 9-26 AH A 0CBPKZ0194ZZ/ 9-16 AC C 0CBPZZ0906ZZ/ 9-27 AH A 0CBPZZ0940ZZ/ 9-32 AB C 0CBUAC0289AK/ 9-41 AD B

″ 9-42 AD B 0CBUAG0161AC/ 9-37 AQ B 0CBUAY0016CK/ 9-39 AD B

″ 9-40 AD B 0CBUBC0125DK/ 9-18 AD B

″ 9-19 AD B

″ 9-20 AD B

″ 9-21 AD B

0CBUBC0302BZ/ 9-24 AE B 0CBUBC0336AZ/ 9-23 AL B 0CBUBDAX270A/ 9-69 AD B 0CBUBDBE200D/ 9-73 AD B 0CBUBDBM300D/ 9-71 AC B 0CBUBXAD2R0A/ 9-70 AD B 0CBUBXAD6R2C/ 9-72 AD B 0CBUBY0020AK/ 9-22 AD B 0CBUCB0199AZ/ 9-29 AR B 0CBUDA0128AK/ 9-38 AD B 0CBUDC0163CZ/ 9-35 AG B

″ 9-36 AG B 0CBUDC0232AK/ 9-66 AF B 0CBUEEC105CH/ 9-44 AC C

″ 9-45 AC C 0CBUEEC335CH/ 9-43 AC C 0CBUEFDR33DB/ 9-52 AE C 0CBUEXCAO000/ 9-5 AB C 0CBUEXCAS103/ 9-64 AB C 0CBUEXCAS152/ 9-47 AB C

″ 9-56 AB C 0CBUEXCAS154/ 9-63 AB C 0CBUEXCAS183/ 9-48 AB C 0CBUEXCAS184/ 9-54 AB C 0CBUEXCAS223/ 9-58 AB C 0CBUEXCAS273/ 9-60 AB C 0CBUEXCAS330/ 9-49 AB C 0CBUEXCAS331/ 9-46 AB C 0CBUEXCAS334/ 9-57 AB C 0CBUEXCAS390/ 9-53 AB C

0CBUEXCAS471/ 9-51 AB C 0CBUEXCAS472/ 9-55 AB C

″ 9-61 AB C ″ 9-62 AB C

0CBUEXCAS473/ 9-50 AB C 0CBUEXCAS822/ 9-59 AB C 0CBUEZ0507ZZ/ 9-67 AD B 0CBUFBA102FE/ 9-68 AD B 0CBUGAB101RV/ 9-12 AF C 0CBUGAC222VV/ 9-9 AK C 0CBUGAE561TS/ 9-7 AH C 0CBUGCM392BJ/ 9-6 AF C 0CBUGCU681BR/ 9-14 AC C 0CBUGCV102HZ/ 9-3 AD C 0CBUGFF223EH/ 9-15 AC C 0CBUGFF474JA/ 9-8 AF C 0CBUGFM224KR/ 9-1 AF C 0CBUGXAED104/ 9-10 AC C 0CBUGXAEF102/ 9-13 AC C 0CBUGXAEF222/ 9-4 AC C 0CBUGZ1041ZZ/ 9-11 AF C 0CBUGZ1072ZZ/ 9-2 AN C 0CBUKZ0826ZZ/ 9-30 AK C 0CBUZZ0156ZZ/ 9-31 AN C 0CB829655027/ 9-65 BE B

UX-68DE FO-78DE

SHARP CORPORATION Communication Systems Group Quality & Reliability Control Center Higashihiroshima, Hiroshima 739-0192, Japan

Printed in Japan

A0002-614NS•IS•P

No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.

Sharp UX-68, FO-78 Service Manual

Specifications and Main Features

Frequently Asked Questions

User Manual