Sega CLUB KART User Manual

1ST PRINTING MAY 01

Standard Version

Owner’s ManualOwner’s Manual

Owner’s Manual

Owner’s ManualOwner’s Manual

SEGA ENTERPRISES, INC. USA

MANUAL NO. 999-1282

Warranty

Your new Sega Product is covered for a period of 90 days from the date of shipment. This certifies
that the Printed Circuit Boards, Power Supplies and Monitor are to be free of defects in workman­ship or materials under normal operating conditions. This also certifies that all Interactive Control
Assemblies are to be free from defects in workmanship and materials under normal operating condi­tions. No other product in this machine is hereby covered.

Sellers sole liability in the event a warranted part described above fails shall be, at its option, to
replace or repair the defective part during the warranty period. For Warranty claims, contact your
Sega Distributor.

Should the Seller determine, by inspection that the product was caused by Accident, Misuse, Ne­glect, Alteration, Improper Repair, Installation or Testing, the warranty offered will be null and void.

Under no circumstances is the Seller responsible for any loss of profits, loss of use, or other dam­ages.

This shall be the exclusive written Warranty of the original purchaser expressed in lieu of all other
warranties expressed or implied. Under no circumstance shall it extend beyond the period of time
listed above.

BEFORE USING THE PRODUCT, BE SURE TO READ THE FOLLOWING:

To maintain the safety:

To ensure the safe usage of the product, be sure to read the following before using the product. The following
instructions are intended for the users, operators and the personnel in charge of the operation of the product.
After carefully reading and sufficiently understanding the warning displays and cautions, handle the product
appropriately. Be sure to keep this manual nearby the product or elsewhere convenient for referring to it
when necessary.

Herein, explanations which require special attention are enclosed with dual lines. Depending on the poten­tially hazardous degrees, the terms of WARNING, CAUTION, etc. are used. Be sure to understand the
contents of the displays before reading the text.

Indicates that mishandling the
product by disregarding this
warning will cause a potentially
hazardous situation which can
result in death or serious injury.

For the sage usage of the product, the following pictographs are used:

Indicates “HANDLE WITH CARE.” In order to protect the human body an equipment, this
display is attached to places where the Owner’s Manual and or Service Manual should be referred
to.

Perform work in accordance with the instructions herein stated.

Instructions for work are explained by paying attention to the aspect of accident prevention. Failing to
perform work as per the instructions can cause accidents. In the case where only those who have techni­cal expertise should perform the work to avoid hazardous situation, the instructions herein state that the
serviceman should perform such work.

Be sure to turn off power before working on the machine.

To prevent electric shock, be sure to turn off power before starting the work in which the worker touches
the interior of the product. If the work is to be performed in the power-on status, the Instruction Manual
herein always states to that effect.

Indicates that mishandling the product
by disregarding this caution will cause
a slight hazardous situation which can
result in personal injury and or material
damage.

Be sure to ground the Earth Terminal (this, however, is not required in the case where a power cord
with earth is used).
This product is equipped with the Earth Terminal. When installing the product, Connect the Earth Termi­nal to the “accurately grounded indoor earth terminal” by using an earth wire. Unless the product is
grounded appropriately, the user can be subject to electric shock. After performing repair, etc. for the
Control equipment, ensure that the Earth Wire is firmly connected to the Control equipment.

Ensure that the Power Supply used is equipped with an Earth Leakage Breaker.

This product does not incorporate the Earth Leakage Breaker. Using a power supply which is not
equipped with the Earth Leakage Breaker can cause a fire when earth leakage occurs.

Be sure to use fuses which meet the specified rating. (only for the machines which use fuses).
Using fuses exceeding the specified rating can cause a fire and electric shock.

Specification changes (removal of equipment, conversion and addition) not designated by SEGA
are not allowed.

The parts of the product include warning labels for safety, covers for personal protection, etc. It is very
hazardous to operate the product by removing parts and or modifying the circuits. Should doors, lids
and protective parts be damaged or lost, refrain from operating the product, and contact where the
product was purchased from or the office herein stated. SEGA shall not be held responsible for any
accidents, compensation for damage to a third party, resulting from the specifications not designated by
SEGA.

Ensure that the product meets the requirements of appropriate Electrical Specifications.

Before installing the product, check for Electrical Specifications. SEGA products have a nameplate on
which Electrical Specifications are described. Ensure that the product is compatible with the power
supply voltage and frequency requirements of the location. Using any Electrical Specifications different
from the designated Specifications can cause a fire and electric shock.

Install and operate the product in places where appropriate lighting is available, allowing warning
labels to be clearly read.

To ensure safety for the customers, labels and printed instructions describing potentially hazardous
situation are applied to places where accidents can be caused. Ensure that where the product is operated
has sufficient lighting allowing the warnings to be read. If any label is peeled off, apply it again imme­diately. Please place an order with where the product was purchased from or the office herein stated.

When handling the Monitor, be very careful. (Applies only to the product w/monitor.)

Some of the monitor (TV) parts are subject to high tension voltage. Even after running off power, some
portions are still subject to high tension voltage sometimes. Monitor repair and replacement should be
performed only be those technical personnel who have knowledge of electricity and technical expertise.

Be sure to adjust the monitor (projector) properly. (Applies only to the product w/monitor.)

Do not operate the product leaving on-screen flickering or blurring as it is. Using the product with the
monitor not properly adjusted may cause dizziness or a headache to an operator, a player, or the custom­ers.

When transporting or reselling this product, be sure to attach this manual to the product.

In the case where commercially available monitors and printers are used in this product, only the
contents relating to this product are explained herein. Some commercially available equipment has
functions and reactions not stated in this manual. Read this manual together with the specific Instruc­tion Manual of such equipment.

•

Descriptions herein contained may be subject to improvement changes without notice.

•

The contents described herein are fully prepared with due care. However, should any question arise or
errors be found, please contact SEGA.

INSPECTIONS IMMEDIATELY AFTER TRANSPORTING THE PRODUCT TO THE LOCATION.

Normally, at the time of shipment, SEGA products are in a status allowing for usage immediately after
transporting to the location. Nevertheless, an irregular situation may occur during transportation. Before
turning on power, check the following points to ensure that the product has been transported in a satisfac­tory status.
Are there any dented portions or defects (cuts, etc.) on the external surfaces of the cabinet?
Are Casters and Adjusters, damaged?
Do the power supply voltage and frequency requirements meet with those of the location?
Are all wiring connectors correctly and securely connected? Unless connected in the correct direction,
connector connections can not be made accurately. Do not insert connectors forcibly.
Do power cords have cuts and dents?
Do the fuses used meet specified rating? Is the Circuit Protector in an energized status?
Are all accessories available?
Can all Doors and Lids be opened with the Accessory keys? Can Doors and Lids be firmly closed?

TABLE OF CONTENTS

BEFORE USING THE PRODUCT, BE SURE TO READ THE FOLLOWING:
TABLE OF CONTENTS
INTRODUCTION OF THE OWNER’S MANUAL

1. HANDLING PRECAUTIONS ..........................................................................................

2. PRECAUTIONS CONCERNING INSTALLATION LOCATION ...................................

3. OPERATION .....................................................................................................................

4. ACCESSORIES .................................................................................................................

5. ASSEMBLING AND INSTALLATION ............................................................................

6. PRECAUTIONS TO BE HEEDED WHEN MOVING THE MACHINE ........................

7. CONTENTS OF GAME ....................................................................................................

8. EXPLANATION OF TEST AND DATA DISPLAY .........................................................

8 - 1 SWITCH UNIT AND COIN METER ............................................................

8 - 2 SYSTEM TEST MODE ..................................................................................

8 - 3 GAME TEST MODE ......................................................................................

9. CONTROL PANEL ..........................................................................................................

9 - 1 ADJUSTING/REPLACING THE V.R. ..........................................................

9 - 2 GREASING ....................................................................................................

10. ACCELERATOR & BRAKE ............................................................................................

10 - 1 ADJUSTING AND REPLACING THE V.R. .................................................

10 -2 GREASING .....................................................................................................

11. COIN SELECTOR ............................................................................................................

12. REPLACING THE FLOURESCENT LAMP, AND LAMPS ..........................................

13. PERIODIC INSPECTION TABLE ..................................................................................

14. TROUBLESHOOTING ....................................................................................................

15. GAME BOARD ................................................................................................................

15 - 1 REMOVING THE GAME BOARD ..............................................................

16. COMMUNICATION PLAY .............................................................................................

16 - 1 INSTALLATION PRECAUTIONS ..............................................................

16 - 2 SETTING FOR COMMUNICATION PLAY ...............................................

16 - 3 CAUTIONS TO BE HEEDED DURING COMMUNICATION PLAY ......

17. DESIGN RELATED PARTS ............................................................................................

18. PARTS LIST .....................................................................................................................

19. WIRE COLOR CODE TABLE .........................................................................................

20. WIRING DIAGRAM ........................................................................................................

1
2 - 3
4 - 5
6 - 7
8 - 15
16
17 - 23
24 - 62
26 - 27
28 - 40
41 - 62
63 - 66
63 - 66
66
67 - 68
67 - 68
68
69 - 72
73 - 74
75 - 76
77 - 78
79 - 80
80
81 - 84
81 - 82
83 - 84
84
85 - 86
87 - 104
105
106 - 109

INTRODUCTION OF THE OWNERS MANUAL

This Owner's Manual is intended to provide detailed descriptions together with all
the necessary information covering the general operation of electronic assemblies,
electromechanicals, servicing control, spare parts, etc. as regards the product,

CLUB KART STD TYPE.

This manual is intended for the owners, personnel and managers in charge of
operation of the product. Operate the product after carefully reading and sufficiently
understanding the instructions. If the product fails to function satisfactorily, non­technical personnel should under no circumstances touch the internal system. Please
contact where the product was purchased from.

Use of this product is unlikely to cause physical injuries or damages to property. However,
where special attention is required this is indicated by a thick line, the word "IMPORTANT"
and its sign in this manual.

STOP

Indicates that mishandling the product by disregarding this display can cause the
product's intrinsic performance not to be obtained, resulting in malfunctioning.

IMPORTANT

SEGA ENTERPRISES, INC. (U.S.A.)/CUSTOMER SERVICE
45133 Industrial Drive, Fremont, California 94538, U.S.A.

Phone : [phone]
Fax : [phone]

DEFINITION OF LOCATION MAINTENANCE MAN AND SERVICEMAN

Non-technical personnel who do not have technical knowledge and expertise should
refrain from performing such work that this manual requires the location's
maintenance man or a serviceman to carry out, or work which is not explained in
this manual. Failing to comply with this instruction can cause a severe accident
such as electric shock.

Ensure that parts replacement, servicing & inspections, and troubleshooting are performed by the
location's maintenance man or the serviceman. It is instructed herein that particularly hazardous
work should be performed by the serviceman who has technical expertise and knowledge.

The location's maintenance man and serviceman are herein defined as follows:

"Location's Maintenance Man" :

Those who have experience in the maintenance of amusement equipment and vending machines,
etc., and also participate in the servicing and control of the equipment through such routine work
as equipment assembly and installation, servicing and inspections, replacement of units and
consumables, etc. within the Amusement Facilities and or locations under the management of the
Owner and Owner's Operators of the product.

Activities of Location's Maintenance Man :

Assembly & installation, servicing & inspections, and replacement of units & consumables as
regards amusement equipment, vending machines, etc.

Serviceman :

Those who participate in the designing, manufacturing, inspections and maintenance service of
the equipment at an amusement equipment manufacturer.
Those who have technical expertise equivalent to that of technical high school graduates as re­gards electricity, electronics and or mechanical engineering, and daily take part in the servicing &
control and repair of amusement equipment.

Serviceman's Activities :

Assembly & installation and repair & adjustments of electrical, electronic and mechanical parts of
amusement equipment and vending machines.

LISTED

U

®

L

5K92

AMUSEMENT MACHINE

1. HANDLING PRECAUTIONS

When installing or inspecting the machine, be very careful of the following points and pay
attention to ensure that the player can enjoy the game safely.
Non-compliance with the following points or inappropriate handling running counter to the
cautionary matters herein stated can cause personal injury or damage to the machine.

Before performing work, be sure to turn power off. Performing the work
without turning power off can cause an electric shock or short circuit. In the
case work should be performed in the status of power on, this manual always
states to that effect.
To avoid electric shock or short circuit, do not plug in or unplug quickly.
To avoid electric shock, do not plug in or unplug with a wet hand.
Do not expose Power Cords and Earth Wires on the surface, (floor, passage,
etc.). If exposed, the Power Cords and Earth Wires are susceptible to damage.
Damaged cords and wires can cause electric shock or short circuit.
To avoid causing a fire or electric shock, do not put things on or damage
Power Cords.
When or after installing the product, do not unnecessarily pull the power cord.
If damaged, the power cord can cause a fire or electric shock.
In case the power cord is damaged, ask for replacement through where the
product was purchased from or the office herein stated. Using the cord as is
damaged can cause fire, electric shock or leakage.
Be sure to perform grounding appropriately. Inappropriate grounding can
cause an electric shock.
Be sure to use fuses meeting specified rating. Using fuses exceeding the
specified rating can cause a fire or electric shock.
Completely make connector connections for IC BD and others. Insufficient
insertion can cause an electric shock.
Specification changes, removal of equipment, conversion and/or addition, not
designated by SEGA are not permitted.

• Failure to observe this may cause a fire or an electric shock. Non-compliance
with this instruction can have a bad influence upon physical conditions of the
players or the lookers-on, or result in injury during play.

• SEGA shall not be held responsible for damage, compensation for damage to
a third party, caused by specification changes not designated by SEGA.
Be sure to perform periodic maintenance inspections herein stated.

STOP

IMPORTANTIMPORTANT

IMPORTANT

IMPORTANTIMPORTANT

For the IC board circuit inspections, only the logic tester is allowed. The use
of a multiple-purpose tester is not permitted, so be careful in this regard.

1

2. PRECAUTIONS CONCERNING INSTALLATION

LOCATION

This product is an indoor game machine. Do not install it outside. Even indoors,
avoid installing in places mentioned below so as not to cause a fire, electric shock,
injury and or malfunctioning.

Places subject to rain or water leakage, or places subject to high humidity in
the proximity of an indoor swimming pool and or shower, etc.
Places subject to direct sunlight, or places subject to high temperatures in the
proximity of heating units, etc.
Places filled with inflammable gas or vicinity of highly inflammable/volatile
chemicals or hazardous matter.
Dusty places.
Sloped surfaces.
Places subject to any type of violent impact.
Vicinity of anti-disaster facilities such as fire exits and fire extinguishers.
The operating (ambient) temperature range is from 5 C° to 40 C°.
Only in the case a projector is employed, the temperature range is from 5 C°
to 30 C°.

LIMITATIONS OF USAGE REQUIREMENTS

Be sure to check the Electrical Specifications.
Ensure that this product is compatible with the location's power supply,
voltage and frequency requirements.
A plate describing Electrical Specifications is attached to the product.
Non-compliance with the Electrical Specifications can cause a fire and
electric shock.
This product requires the Breaker and Earth Mechanisms as part of the
location facilities. Using them in a manner not independent can cause a fire
and electric shock.
Ensure that the indoor wiring for the power supply is rated at 15A or higher
(AC single phase 100 ~ 120V area), and 7A or higher (AC 220 ~ 240V area).
Non-compliance with the Electrical Specifications can cause a fire and
electric shock.
Be sure to independently use the power supply equipped with the Earth
Leakage Breaker. Using a power supply without the Earth Leakage Breaker
can cause an outbreak of fire when earth leakage occurs.
Putting many loads on one electrical outlet can cause generation of heat and a
fire resulting from overload.
When using an extension cord, ensure that the cord is rated at 15A or higher
(AC 100 ~ 120V area) and 7A or higher (AC 220 ~ 240V area). Using a cord
rated lower than the specified rating can cause a fire and electric shock.

2

OPERATION AREA

For the operation of this machine, secure a minimum area of 2.0m (W) X

2.8m (D). In order to prevent injury resulting from the falling down accident
during game play, be sure to secure the minimum area for operation.
Be sure to provide sufficient space so as to allow this product's ventilation fan
to function efficiently. To avoid machine malfunctioning and a fire, do not
place any obstacles near the ventilation opening.
SEGA shall not be held responsible for damage, compensation for damage to
a third party, resulting from the failure to observe this instruction.

STOP

IMPORTANTIMPORTANT

IMPORTANT

IMPORTANTIMPORTANT

For transporting the machine into the location's building, the minimum necessary
dimensions of the opening (of doors, etc.) are 1.4m(W) and 1.7m(H).

3

3. OPERATION

2

2

PRECAUTIONS TO BE HEEDED BEFORE STARTING THE OPERATION

To avoid injury and trouble, be sure to constantly give careful attention to the behavior and
manner of the visitors and players.

In order to avoid accidents, check the following before starting the operation:

To ensure maximum safety for the players and the customers, ensure that
where the product is operated has sufficient lighting to allow any warnings to
be read. Operation under insufficient lighting can cause bodily contact with
each other, hitting accident, and or trouble between customers.
It is suggested to ensure a space allowing the players who feel sick while
playing the game to take a rest.

2345678901234567890123456789012123456789012345678901

2345678901234567890123456789012123456789012345678901

Ensure that all of the
Adjusters are in contact

with the floor.

Do not put any heavy item on this product. Placing any heavy item on the
product can cause a falling down accident or parts damage.
Do not climb on the product. Climbing on the product can cause falling down
accidents. To check the top portion of the product, use a step.
To avoid electric shock, check to see if door & cover parts are damaged or
omitted.
To avoid electric shock, short circuit and or parts damage, do not put the
following items on or in the periphery of the product.
Flower vases, flowerpots, cups, water tanks, cosmetics, and receptacles/
containers/vessels containing chemicals and water.

4

To avoid injury, be sure to provide sufficient space by considering the potentially
crowded situation at the installation location. Insufficient installation space can
cause making bodily contact with each other, hitting accidents, and or trouble
between customers.

PRECAUTIONS TO BE HEEDED DURING OPERATION (PAYING ATTENTION TO CUSTOMERS)

To avoid injury and trouble, be sure to constantly give careful attention to the behavior and
manner of the visitors and players.

To avoid injury and accidents, those who fall under the following categories
are not allowed to play the game.

• Those who need assistance such as the use of an apparatus when walking.

• Those who have high blood pressure or a heart problem.

• Those who have experienced muscle convulsion or loss of consciousness when

playing video game, etc.

• Those who have a trouble in the neck and or spinal cord.

• Intoxicated persons.

• Pregnant women or those who are in the likelihood of pregnancy.

• Persons susceptible to motion sickness.

• Persons whose act runs counter to the product's warning displays.
A player who has never been adversely affected by light stimulus might

experience dizziness or headache depending on his physical condition when
playing the game. Especially, small children can be subject to those
conditions. Caution guardians of small children to keep watch on their
children during play.

Instruct those who feel sick during play to have a medical examination.
To avoid injury resulting from falling down and electric shock due to spilled

drinks, instruct the player not to place heavy items or drinks on the product.
To avoid electric shock and short circuit, do not allow customers to put hands
and fingers or extraneous matter in the openings of the product or small
openings in or around the doors.
To avoid falling down and injury resulting from falling down, immediately
stop the customer's leaning against or climbing on the product, etc.
To avoid electric shock and short circuit, do not allow the customers to
unplug the power plug without a justifiable reason.

Immediately stop such violent acts as hitting and kicking the product. Such
violent acts can cause parts damage or falling down, resulting in injury due to
fragments and falling down.
Instruct the Player to adjust the seat before playing the game. Playing the
game in a forcible posture can cause a contingent accident.

5

4. ACCESSORIES

When transporting the machine, make sure that the following parts are supplied.

TABLE 4 ACCESSORIES

DESCRIPTION OWNERS MANUAL
Part No. (Qty.)

420-6588-01 (1)

Note
Figures

If Part No. has no description, the Number has not been
registered or can not be registered. Such a part may not
be obtainable even if the customer desires to purchase it.
Therefore, ensure that the part is in safekeeping with you.

TAMPERPROOF WRENCH
M8 540-0009-01 (1)

TOOL

CARTON BOX
601-10642 (1)

Used for transporting the
Game Board.
Refer to Next Page.

KEY MASTER
220-5576 (2)

For opening/closing
the doors

AC Cable (Power Cord)
600-7228 (1) TAIWAN
600-6695 (1) USA
600-6618 (1) OTHERS
600-6619 (1) HONG KONG

Used for installation,
see 4 of Section 5.

KEY
(2)

For the CASHBOX DOOR

The Keys are inside the Coin
Chute Door at the time of
shipment from the factory.

C

H

E

C

CONN 22
310-5051-22 (2)

For communication play,
refer to Section 16.

K

S

I

D

E

ASSY FIBER CABLE
600-6275-0500 (1)

For communication play,
refer to Section 16.

6

HOW TO USE THE CARTON BOX

STOP

IMPORTANTIMPORTANT

IMPORTANT

IMPORTANTIMPORTANT

When asking for the replacement or repair of the product's Game Board
(NAOMI 2), be sure to put the Game Board together with the Shield Case in a
Carton Box. Otherwise, the request is not acceptable.
Put the Shield Case in the Carton Box by paying attention to the correct
direction as per the following instructions and as shown by the instructions
printed on the Carton Box. Handling in an erroneous manner can damage the
Game Board.
Remove the Shield Case Brackets from the Shield Case and put the Shield Case
in the Carton Box.

SHIELD CASE BRACKETS
The shape depends on the type of product.

"CHECK SIDE" Display

C

H

E

C

K

S

I

D

E

FILTER BOARD

Wrap the Shield Case with the packing material and put it in the Carton Box as shown. Putting
it upside down or packing otherwise in the manner not shown can damage the Game Board and
parts.

7

5. ASSEMBLING AND INSTALLATION

Perform assembly work by following the procedure herein stated. Failing to
comply with the instructions can cause electric shock hazard.
Perform assembling as per this manual. Since this is a complex machine,
erroneous assembling can cause an electric shock, machine damage and or not
functioning as per specified performance.
When assembling, be sure to use plural persons. Depending on the assembly
work, there are some cases in which working by one person alone can cause
personal injury or parts damage.
Ensure that connectors are accurately connected. Incomplete connections can
cause electric shock hazard.
Be careful so as not to damage wirings. Damaged wiring can cause electric
shock and short circuit hazards.
This work should be performed by the Location's Maintenance Man or
Serviceman. Performing work by non-technical personnel can cause a severe
accident such as electric shock. Failing to comply with this instruction can
cause a severe accident such as electric shock to the player during operation.
Provide sufficient space so that assembling can be performed. Performing
work in places with narrow space or low ceiling may cause an accident and
assembly work to be difficult.
To perform work safely and avoid serious accident such as the cabinet's
falling down, do not perform work in places where step-like grade.

To perform work safely and securely, be sure to prepare a step which is in a
secure and stable condition. Performing work without using the step can cause
violent falling down accidents.

8

When carrying out the assembling and installation, follow the following 6-item sequence.

1

SECURING IN PLACE (ADJUSTER ADJUSTMENT)

2

POWER SUPPLY CONNECTION

3

TURNING POWER ON

4

ASSEMBLING CHECK

The master key (accessories) in addition to the tools such as a Phillips type screwdriver, wrench,
socket wrench and Ratchet Handle are required for the assembly work.

Phillips type screwdriver

✶✸❧❧

SOCKET WRENCH,(M8 hexagon bolt)
RATCHET HANDLE

WRENCH (for M16 hexagon bolt)

KEY MASTER

9

1

SECURING IN PLACE (ADJUSTER ADJUSTMENT)

Make sure that all of the adjusters are in contact with the floor. If they are not, the
cabinet can move and cause an accident.

This product has 6 casters and 6 Adjusters. When the installation position is determined, cause
the adjusters to come into contact with the floor directly, make adjustments in a manner so that
the casters will be raised approximately 5mm. from the floor and make sure that the machine
position is level.

1

Transport the product to the
installation position. Be sure to
provide adequate space allowing
the player to get on and off.

2

Have all of the Adjusters make
contact with the floor. Adjust the
Adjuster's height by using a
wrench so that the machine
position is kept level.

ADJUSTER

3

After making adjustment, fasten
the Adjuster Nut upward and
secure the height of Adjuster
(FIG. 5. 3 b).

FIG. 5. 3 b ADJUSTER

CASTER

FASTEN UPWARD.

Approx.5mm

ADJUSTER

10

2

POWER SUPPLY

Be sure to independently use the power supply socket outlet equipped with an
Earth Leakage Breaker. Using a power supply without an Earth Leakage
Breaker can cause a fire when electric leakage occurs.
Ensure that the "accurately grounded indoor earth terminal" and the earth wire
cable are available (except in the case where a power cord plug with earth is
used). This product is equipped with the earth terminal. Connect the earth
terminal and the indoor earth terminal with the prepared cable. If the
grounding work is not performed appropriately, customers can be subjected to
an electric shock, and the product's functioning may not be stable.
Ensure that the power cord and earth wire are not exposed on the surface
(passage, etc.). If exposed, they can be caught and are susceptible to damage.
If damaged, the cord and wire can cause electric shock and short circuit
accidents. Ensure that the wiring position is not in the customer's passage
way or the wiring has protective covering.
After wiring power cord on the floor, be sure to protect the power cord.
Exposed power cord is susceptible to damage and causes an electric shock
accident.

The AC Unit is mounted on the right side of the machine. The AC Unit has Main SW, Circuit
Protector, Earth Terminal and the Inlet which connects the Power Cord.

1

Ensure that the Main SW is OFF.

Main SW off

MAIN SW

FIG. 5. 4 a AC unit

11

3

TURNING POWER ON

Connect the power by turning on the AC unit's main switch. Then the billboard's fluorescent
light comes on.
The monitor displays a system power-on message, and then an advertising screen (a plying-for­hire screen) appears. At the same time the right and left speakers on the control panel output an
advertise sound. The sound is inaudible, however, when you have disabled its function.
Before an advertising screen appears the system automatically conducts an initialization. Do not
touch the product until the system completes an initialization and the advertising screen appears.
During an initialization the handle (steering wheel) turns counterclockwise and clockwise and
stops at the original center position (for a straight-ahead direction). This corrects the volume
value inside the control panel. Do not touch the handle or play the game before an initialization
is completed (that is, the handle automatically stops at the center position). Failure to observe
this may affect the handle's operability and the handle's force feedback (force feedback against
crashing) during playing the game. If the handle's operability or force feedback is abnormal,
disconnect and reconnect the power for initializing the system again.
When you disconnect the power, the system saves the data for the credit number, ranking, and
latest game's score. Assume that the credits effective for playing a game remain when you
disconnect the power. In this case, when you will reconnect the power a game startup screen
will appear with the start button flashing.
If several machines are interconnected or networked for a communication play, the system
checks the network. A network-checking screen as illustrated below appears before an
advertising screen appears. Usually, checking the network takes 1 to 3 minutes. If the system
detects a problem related with the network, it keeps displaying the network-checking screen or
an error message.

FIG. 5. 5 a

Fluorescent lamps are always lit.

On-screen images are outputted.

Handle turns counterclockwise
and clockwise.

FIG. 5. 5 b NETWORK check screen

Sound is emitted.

12

9

9

9

9

9

9

9

9

9

9

9

9

9

9

9

9

9

9

9

4

ASSEMBLING CHECK

In the TEST MODE, ascertain that the assembly has been made correctly and IC BD. is
satisfactory (refer to Section 8).
In the test mode, perform the following test:

(1) MEMORY TEST

RAM TEST

IC15 IC16 IC17S IC18S GOOD
IC22 IC23 IC24S IC25S GOOD
IC28 IC29S GOOD
IC41 GOOD
IC42 GOOD
IC44 IC45S IC46 IC47S GOOD
IC91S IC92S GOOD
IC98 GOOD

OPTIONAL SOUND BOARD:
IC2 GOOD

OPTIONAL COMMUNICATION BOARD:
IC7 IC8 IC9 IC10 GOOD

PRESS TEST BUTTON TO EXIT

(2) C.R.T. TEST

C.R.T. TEST PAGE#1

0 31

RED

GREEN

BLUE

WHITE

PRESS SERVICE BUTTON TO ANOTHER PAGE
PRESS TEST BUTTON TO EXIT

Selecting the RAM TEST on the system test
mode menu screen causes the on-board memory
to be tested automatically. The game board is
satisfactory if the display beside each IC No.
shows GOOD.

In the system test mode menu, selecting C.R.T.
TEST allows the screen (on which the monitor
is tested) to be displayed. Although the monitor
adjustments have been made at the time of
shipment from the factory, color deviation, etc.,
may occur due to the effect caused by
geomagnetism, the location building's steel
frames and other game machines in the
periphery. By watching the test mode screen,
make judgment as to whether an adjustment is
needed.

234567890123456789012345678

234567890123456789012345678

234567890123456789012345678

C.R.T. TEST PAGE#2

234567890123456789012345678

234567890123456789012345678

234567890123456789012345678

234567890123456789012345678

234567890123456789012345678

234567890123456789012345678

234567890123456789012345678

234567890123456789012345678

234567890123456789012345678

234567890123456789012345678

234567890123456789012345678

234567890123456789012345678

234567890123456789012345678

234567890123456789012345678

234567890123456789012345678

PRESS SERVICE BUTTON TO ANOTHER PAGE

234567890123456789012345678

PRESS TEST BUTTON TO EXIT

13

(3) SOUND TEST

SOUND TEST

MAIN SPEAKER LEFT
MAIN SPEAKER RIGHT
OPTION SPEAKER LEFT
OPTION SPEAKER RIGHT
> EXIT

SELECT WITH SERVICE BUTTON
AND
PRESS TEST BUTTON

(4) INPUT TEST

INPUT TEST

STEERING WHEEL XXX
GAS PEDAL XXX
BRAKE PEDAL XXX
GEAR POSITION ON
START BUTTON OFF
VIEW CHANGE BUTTON OFF

SERVICE SWITCH OFF
TEST SWITCH OFF

In the system test mode, selecting SOUND
TEST causes the screen (on which sound
related BD and wiring connections are
tested) to be displayed.
Check if the sound is satisfactorily emitted
from each speaker and the sound volume is
appropriate.

Selecting the INPUT TEST on the game test
mode menu screen causes the screen (on
which each switch is tested) to be displayed.
Press each switch. For the coin switch test,
insert a coin from the coin inlet with the coin
chute door open. If the display beside each
switch indicates "ON," the switch and
wiring connections are satisfactory.

PRESS TEST AND SERVICE BUTTON TO EXIT

JVS TEST
> DISPLAY CONFIG
EXIT

NODE 1/1
SWITCH
SYSTEM ________
PLAYER1 _____________
PLAYER2 _____________
COIN
SLOT1 0000 SLOT2 8000
ANALOG
CH1 0000 CH2 0000 CH3 0000 CH4 0000
CH5 0000 CH6 0000 CH7 0000 CH8 0000

SELECT WITH SERVICE BUTTON
AND
PRESS TEST BUTTON

14

(5) OUTPUT TEST

OUTPUT TEST

> START BUTTON
VIEW CHANGE BUTTON
BASS SHAKER(FRONT)
BASS SHAKER(FRONT+REAR)

PRESS TEST BUTTON TO EXIT

Perform the above inspections also at the time of monthly inspection.

Select OUTPUT TEST from the Menu
screen in the Game Test Mode to cause the
screen (on which output unit such as lamps
and wiring connections are tested) to appear.
Ensure that the output unit functions
satisfactorily.

15

6.

PRECAUTIONS TO BE HEEDED WHEN MOVING THE MACHINE

When moving the machine, be sure to unplug the power plug. Moving the
machine with the plug as is inserted can damage the power cord and cause fire
and electric shock hazards.
When moving the machine on the floor, retract the Adjusters and ensure that
Casters make contact with the floor. During transportation, pay careful
attention so that Casters do not tread power cords and earth wires. Damaging
the power cords can cause electric shock and short circuit hazards.
When lifting the cabinet, be sure to hold the grip portions or bottom part.
Lifting the cabinet by holding other portions can damage parts and installation
portions due to the empty weight of the cabinet, and cause personal injury.
When transporting the product in places with step-like differences in grade,

disassemble into each unit before transporting. Lifting up the product in an
attempt to cross the step-like differences in an as is assembled condition may
damage the unit's joining portions and cause a personal injury resulting from
damage.
Do not insert the fork to places other than designated when using a Forklift to

transport the machine.
Failure to observe this could cause falling down and injury resulting from
falling down.

STOP

IMPORTANTIMPORTANT

IMPORTANT

IMPORTANTIMPORTANT

Do not push the plastic made parts. Failure to observe this may damage parts
and cause injury due to fragments resulting from damage.
Do not use the handle or lever to move the product. Failure to observe this
may cause the parts to be deformed or damaged.

When transporting the product in places with steps, disassemble into each unit
before transporting. Inclining the product in an as is assembled condition or
placing the cabinet in places with steps can damage the unit's joining portions.
To protect surface, do not directly apply a rope to the surfaces of product.
Use protective materials to the places the rope is applied to.

16

7. CONTENTS OF GAME

The following explanations apply to the case the product is functioning satisfactorily. Should
there be any moves different from the following contents, some sort of faults may have
occurred. Immediately look into the cause of the fault and eliminate the cause thereof to ensure
satisfactory operation.

Advertising (Plying-for-Hire) Performance

The billboard's fluorescent light is always on when the power is connected.
The monitor displays the demonstration images and ranking data. The ranking data is updated
every week.
The lights (integrated with the two buttons on the control panel) are off.
The right and left speakers on the control panel output an advertise sound. The right and left
speakers on the seat backrest and the bass shaker do not output an advertise sound.
You can activate or deactivate an advertise sound output function on the test mode screen.

Fluorescent lamps are lit.

Image output on the monitor.

Coin Inlet

FIG. 7 a

Emits sounds.

17

HOW TO PLAY

Operation of a single machine allows a Single Play. Operation of interconnected machines
allows a Communication Play.

START BUTTON

VIEW CHANGE BUTTON

BRAKE PEDAL

GAS (ACCELLETOR) PEDAL

[Single Play]

In this game, the players make their karts and
enter the race for competing with each other.

STEERING WHEEL
HANDL❉

FIG. 7 b

By achieving a good score in the Championship Race mode, you can step up from “Class Novice” (at start) to
“Class B,” “Class A,” and “Class S.”
When you step up to a higher class, you may get an extended course along which you can drive, or the
performance of the kart with your character may vary. The goal is to win in the race in the environment that
may vary in such a manner.
By selecting “Practice Race,” you can select and run along the course for a series of races, if you desire.

This game allows the data to be retained through the cards system. In addition to the kart’s name, frame,
cowl, suits, helmet, etc., information such as the total time, achievements in a series of races, the highest rank
by class can be recorded on the “Club Kart Card” (hereafter “CARD”).

18

How to Play the Game --- If you play the Championship Race for the first time:

• Throw coins into the slot. At this time, the value

converted for the number of credits is displayed at
the bottom right corner of the screen.
When you throw into the slot the number of coins
enabling operation of one play session, you go to
the screen that asks whether you have a card.

• In response to the inquiry, “Do you want to create

a new card?”

• If you answer with “NO,” or you do not insert any

card after you answer with “YES,” Rental Kart is
automatically selected as the type of the kart you
can luse. In this case, you go to Step 1 (creating a
new card). One more credit is required in this case.

• If you throw a card into the slot without making

the selection, you will go to selection of the Race
Mode.

Rental Kart Mode

In the Rental Kart Mode, you select and run along the desired one of four courses for competition in lap time.
You choose either one of two types of karts: for the novice and middle classes. You are required to make the
specified number of circuits of the course within the predetermined time-out time.

• Once you complete the first circuit, the remaining time of the time-out time for the first circuit is added to

the time-out time for the second circuit.

• When you complete the specified number of circuits of the course within the specified time, the finish takes

place. When the time-out time reaches 0, Game Over takes place.

An example where “YES” was selected is described in this document.

19

• Create a new card.

After entering the name, select the cowl, frame, and racing suite colors and the helmet design according to the
instructions on the screen.

• After you have entered all the information, you go to the confirmation screen and must make operations

according to the instructions on the screen.

• Select the Race Mode.

You can choose either Championship Race or
Practice Race. (“Communicated Race” is
additionally displayed when two or more
machines are interconnected.) Turn the
steering wheel clockwise or counterclockwise
for selection. Then, determine the selection
by pressing the accelerator pedal.

20

Championship Race

• In this mode, you compete with the other players for the total achievement of a Series of Races that are

done, depending on four classes (Novice, B, A, and S). The race in this mode begins after you have created
the feature of creating your own original kart (one of the distinctive features of this game) and the card to save
the running record.
With the card, you can save the data before completion of the series of races; at the next play time, you can
resume the game from the ending point in the previous session of the game.

Practice Race

You can select and run along the desired one of the courses along which you run in a Series of Races.
The number of courses from among which can select depends on the number of racces included in the series,
which varies with the class to which you belong (4 of Novice, 6 for B, 8 for Class, and 10 for S).

• Information about the player’s kart (class, the number fo times won and defeated, the top ranking, the best

time, the number of races in the series, etc.) and the course map are displayed before the race starts.
When you created a card for the first time, the player’s kart starts at the rearmost position.
You are required to make the specified number of circuits of the course within the predetermined time-out
time. Once you complete the first circuit, the remaining time of the time-out time for the first circuit is added
to the time-out time for the second circuit.When you complete the specified number of circuits of the course
within the specified time, the finish takes place. When the time-out time reaches 0, Game Over takes place.

• If your kart touches the wall of the course or another kart or goes outside the course while the game is in

progress, you feel a reaction through the steering wheel.

• While the game is in progress, pressing the Viewpoint Change button changes the viewpoint on the screen.

The button is continually flashing while the game is in progress.

• While the game is in progress, pressing the Start button toggles between the map that shows the player

kart’s and the time display that indicates the other karts’ positions and the best time in the class and that of
your records.

• After each race is completed, the Results Screen appears if you have run along the whole course. After the

Results Screen appears, the Select Sponsor Screen may appear, depending on the results of the series of races.
The number of sponsors, at random, increases or decreases, depending on the achievement. The logo of the
sponsor you selected can be attended to the kart if you desire this.

When Select Sponsor Screen appears for the first time,
you assign the team name to your kart.

21

• For a Series of Races, the total achievements

are listed when the predetermined number of
races have been completed for each of the
classes. If you have established good achieve­ment, a screen appears that lets you select
whether to try the next series of races at the
current or upper class.

• If the Practice Race Mode is entered or all the credits have been exhausted after the data is written onto the

card after completion, Game Over takes place. If you are in the Championship Race Mode, you go to the
Continue Screen.
If you still have credits for one or more play sessions at this time in the Championship Race Mode, you can
go to the next course and enjoy one or more play sessions after jumping to the course map display is Step ???.

22

[Communicated Play]

Communicated Play differs slightly from Single Play regarding the game starting procedure and how to play
the game.

• When coins you throw into the slot the coins with which you can enjoy a play session, the Entry Screen

appears and, at the same time, the Start button begins to flash.

• If you desire a competitive play, throw the appropriate number of coins into the slot at another seat.

If you desire the single play mode, press the Start button immediately after the Entry Screen appears.

• Once the Entry Screen appears, a countdown starts. If a person who desires to compete with you does not

appear before the count reaches 0 (zero), you have to enjoy the game in the Single Play Mode.

• Once the count in the Entry Screen reaches 0, you are brought to the Select Rental Kart Screen.

Turn the steering wheel clockwise or counterclockwise to choose selection by pressing the accelerator pedal
and Start button.
If you have a card, you will be subsequently able to use your own original kart by inserting the card into the
slot.
The course assignments to the players are determined by majority of the players.

• Once the course assignments are determined, information about the players’ karts (class, the number of

times won and defeated, the top ranking, the best time, the number of races in the series, etc.) and the course
map are displayed before the race starts.

• In the race, the players compete with each other for their ranks.

Each time the first-rank player completes one circuit of the course, the time that remained is added to that of
the next circuit of the course.
When you complete the specified number of circuits of the course within the specified time, the finish takes
place. When the time-out time reaches 0, Game Over takes place.

• STEERING DIR

This is a setting about the cabinet. Basically, you do not need to change it. You should use the factory­adjusted setting.

• CARD SYSTEM

This sets the mode of operation for the card system unit. For usual operation, set ENABLE. If the card
system unit is detached from the system, set DISABLE.

• BONUS GAMES

This sets the count of plays given as a bonus when a new card is created. By setting this, the count can be set
to 0 to 3 times.

23

8. EXPLANATION OF TEST AND DATA DISPLAY

By operating the switch unit, periodically perform the tests and data check. When installing the
machine initially or collecting cash, or when the machine does not function correctly, perform
checking in accordance with the explanations given in this section.
The following shows tests and modes that should be utilized as applicable.
SEGA HIKARU GAME BOARD is used for the product. The system of this game board
allows another game to be played by replacing the ROM Board Case mounted on the SEGA
HIKARU CASE. As such, the Test Mode of this system consists of the System Test Mode for
the system to execute SELF-TEST, COIN ASSIGNMENTS, etc. used in common for the
machines employing the SEGA HIKARU BOARD, and the Game Test Mode for the specific
product to execute Input/Output test for the operation equipment, difficulty setting, etc.

STOP

IMPORTANTIMPORTANT

IMPORTANT

IMPORTANTIMPORTANT

The contents of settings changed in the TEST mode are stored when the test
mode is finished from EXIT in the menu mode. If the power is turned off
before the TEST mode is finished, the contents of setting change become
ineffective.
Executing "BACKUP DATA CLEAR" in the SYSTEM TEST MODE does
not clear the BOOKKEEPING data in the GAME TEST mode.
Entering the TEST mode clears fractional number of coins less than one credit
and BONUS ADDER data.
When the 2 or more machines are linked for communication play, be careful
to enter the test mode. If one of the machines linked enters the test mode, all
others display the NETWORK CHECK screen.

24

TABLE 8 EXPLANATION OF TEST MODE

ITEMS DESCRIPTION

REFERENCE
SECTIONS

INSTALLATION
OF MACHINE

MEMORY

PERIODIC
SERVICING

CONTROL
SYSTEM

When the machine is installed, perform the following:

1. Check to see that each setting is as per standard setting made at
the time of shipment.

2. In the INPUT TEST mode, check such input devices as each
SW, V.R., etc.

3. In the OUTPUT TEST mode, check such output devices as
lamps, motors, etc.

4. In the SELF-TEST mode, check ICs on the IC Board.

Choose MEMORY TEST in the MENU mode to allow the
MEMORY test to be performed. In this test, PROGRAM RAMs,
ROMs, and ICs on the IC Board are checked.

Periodically perform the following:

1. MEMORY TEST

2. Ascertain each setting.

3. In the INPUT TEST mode, test the CONTROL device

4. In the OUTPUT TEST mode, check such output devices as
lamps, motors, etc.

1. In the INPUT TEST mode, check such input devices as each
SW, V.R., etc.

2. Adjust or replace each SW and VR.

3. If the problem can not be solved yet, check the CONTROL's
moves.

8-2 F,G, 8-3 F

8-2 C, 8-3 B

8-3 C

8-2 B,J

8-2 B,J

8-2 B,J
8-2 F,G, 8-3 F
8-2 C, 8-3 B
8-3 C

8-2 C, 8-3 B

8-3 D,E,
9,10

MONITOR

IC BOARD

DATA CHECK

In the MONITOR ADJUSTMENT mode,
check to see if the adjustment is appropriately made.

1. MEMORY TEST

2. In the SOUND TEST mode, check the sound related ROMs.

Check such data as game play time and histogram to adjust the
difficulty level, etc.

8-2 E
11

8-2 B,J
8-2 D

8-2 H, 8-3 G

25

8 - 1 SWITCH UNIT AND COIN METER

Never touch places other than those specified. Touching places not specified can
cause electric shock and short circuit hazards.

STOP

IMPORTANTIMPORTANT

IMPORTANT

IMPORTANTIMPORTANT

SWITCH UNIT

Open the coin chute door, and the switch unit shown will appear.
The functioning of each SW is as follows:
The sound volumes of the front and rear speakers are adjusted as indicated by the illustration on
the switch unit, at the factory before shipping. This adjustment aims to attain the best output
balance between the front and rear speakers. Remember that carelessly changing this adjustment
may cause the best balance to be lost.

Adjust to the optimum sound volume by considering the environmental
requirements of the installation location.
If the COIN METER and the game board are electrically disconnected, game
play is not possible.
A cover is provided on the bass shaker output adjustment volume in order to
prevent the BASE SHAKER against being carelessly adjusted.

COIN METER

PUSH BUTTON

SOUND VOLUME

FIG. 8. 1 a SWITCH UNIT

26

TEST BUTTON : For the handling of the test button, refer to the following pages.

TEST

SERVICE BUTTON : Gives credits without registering on the coin meter.

SERVICE

SOUND VOLUME : Adjusts the sound volume of the left and right speakers on the control panel.

FRONT SPEAKER

SOUND VOLUME : Adjusts the sound volume of the left and right speakers on the seat backrest.

REAR SPEAKER

BASE SHAKER Output Adjustment Volume : Adjusts the vibration output of the base shakers each on

BASS SHEAKER

the seat backrest and the control panel.

COIN METER

Open the Cashbox Door by using the key to
have the Coin Meter appear underneath the
Cashbox.

COIN METER

FIG. 8. 1 b COIN METER

27

8 - 2 SYSTEM TEST MODE

STOP

The contents of setting changes in SYSTEM ASSIGNMENTS, COIN
ASSIGNMENTS, and GAME TEST MODE are stored when the test mode is
EXITed. If the power is turned off before EXITing, the contents of setting

IMPORTANTIMPORTANT

IMPORTANT

IMPORTANTIMPORTANT

TEST ITEM SELECT

changes are ineffective. Be very careful of this point.

This test mode mainly allows the IC Board to be checked for accurate functioning, monitor
color to be adjusted as well as COIN ASSIGNMENTS and GAME ASSIGNMENTS to be
adjusted.

After turning power on, press the TEST button to have the following test item menu displayed.

1

SYSTEM MENU

RAM TEST
JVS TEST
SOUND TEST
C.R.T. TEST
SYSTEM ASSIGNMENTS
COIN ASSIGNMENTS
BOOKKEEPING
BACKUP DATA CLEAR
CLOCK SETTING

ROM BOARD TEST
GAME TEST MODE
[XXXXXXXXXXXXXXX]

-> EXIT

SELECT WITH SERVICE BUTTON
AND PRESS TEST BUTTON

2

Press the SERVICE button to move the arrow. Bring the arrow to the desired item and press the
TEST button.

3

Upon finishing the test, bring the arrow to EXIT and press the TEST button to return to the
Game mode.

28

A. RAM TEST

This allows for checking the functioning of the RAM on the NAOMI 2 Main BD.
"GOOD" is displayed for satisfactory RAMs, and "BAD" is indicated for irregular RAMs, if
any.

RAM TEST

TESTING NOW

IC29 GOOD
IC35 GOOD
IC09 GOOD IC10 GOOD
IC11 GOOD IC12 GOOD
IC16 GOOD IC18 GOOD
IC20 GOOD IC22 GOOD
IC17 GOOD IC19 GOOD
IC21 GOOD IC23 GOOD
IC106 GOOD IC107 GOOD
IC108 GOOD IC109 GOOD
IC111 GOOD IC113 GOOD
IC115 GOOD IC117 GOOD
IC112 GOOD IC114 GOOD
IC116 GOOD IC118 GOOD

PRESS TEST BUTTON TO EXIT

"TESTING NOW" shows up (flashing) on the screen during the test.
Returns to the menu screen when the TEST button is pressed after the test is over.

29

B. JVS TEST

In this test, Specifications of the I/O Board connected to NAOMI 2 can be checked, and INPUT
TEST can be performed. First, I/O Board Specifications are displayed.

JVS TEST
INPUT TEST (A)
NEXT NODE (B)

-> EXIT (C)
NODE 1/1
NAME SEGA ENTERPRISES,LTD.
I/O BD JVS
837-13551
Ver 1.00
CMD VER 1.1
JVS VER 2.0
COM VER 1.0
SWITCH 2PLAYER(S) 13BITS
COIN 2SLOT
ANALOG 8CH
ROTARY 0CH
KEYCODE 0
SCREEN X:0 Y:0 CH:0
CARD OSLOT
HOPPER OUT 0CH
DRIVER OUT 6SLOT
ANALOG OUT 0CH
CHARACTER CHARA:0 LINE:0
BACKUP 0

Name and version of I/O BOARD.

123

SELECT WITH SERVICE BUTTON
AND
PRESS TEST BUTTON

Select with the SERVICE button and press the TEST button.
(A) INPUT TEST : Proceeds to the INPUT TEST of I/O BOARD being displayed.
(B) NEXT NODE : In the case where more than 2 I/O Boards are connected, proceeds to

(C) EXIT : Returns to the menu mode.

INPUT TEST SCREEN

JVS TEST
INPUT TEST
NEXT NODE

-> EXIT

NODE 1/1

SWITCH
SYSTEM 00000000
PLAYER1 00000000
00000000
PLAYER2 00000000
00000000
COIN
0000 0000
ANALOG
0000 0000 0000 0000
0000 0000 0000 0000

SELECT WITH SERVICE BUTTON
AND
PRESS TEST BUTTON

the next I/O Board.

When INPUT is performed for the switches
of Control Panel, etc., the value changes to
1 from 0.

If the Coin SW is inputted, the count starts.
When the TEST MODE is finished, the
count is cleared and returned to[0000].

Analogue values are displayed between
0000 and FF00.

30

3

3

3

3

3

3

3

3

3

3

3

3

3

3

3

3

3

C. SOUND TEST

Sound Output test can be performed. Beep sounds can be emitted from each of left/right Speakers.

SOUND TEST

D. C.R.T. TEST

1) RGB COLOR ADJUSTMENT SCREEN
In this page, monitor color can be checked.

RIGHT SPEAKER OFF
LEFT SPEAKER OFF

-> EXIT

SELECT WITH SERVICE BUTTON
AND PRESS TEST BUTTON

C.R.T. TEST 1/2

1 32

RED

GREEN

BLUE

WHITE

Emitted from the right-hand side Speaker.
Emitted from the left-hand side Speaker.
Returns to the menu mode.

Each of red, green, and blue is the darkest at the
leftmost end, and becomes brighter towards the
right-hand end in 31 gradations. Monitor
brightness is satisfactory if the white color bar
is black at the left end and if it is white at the
right end.
Press the TEST button to proceed to the next
page.

PRESS TEST BUTTON TO CONTINUE

2) MONITOR SIZE ADJUSTMENT SCREEN
In this page, monitor size can be checked.

C.R.T. TEST 2/2

234567890123456789012

234567890123456789012

234567890123456789012

234567890123456789012

234567890123456789012

234567890123456789012

234567890123456789012

234567890123456789012

234567890123456789012

234567890123456789012

234567890123456789012

234567890123456789012

234567890123456789012

234567890123456789012

234567890123456789012

234567890123456789012

234567890123456789012

PRESS TEST BUTTON TO EXIT

31

Adjust so that the checkered patterns do not go
beyond the screen.
Press the TEST button to return to the menu
mode.

E. SYSTEM ASSIGNMENTS

The settings of cabinet and board can be changed. Game related assignments such as game
difficulty, etc. are performed in K. GAME TEST MODE.

1

Press the SERVICE button to move the arrow. Bring the arrow to the desired item.

Press the TEST button to change the setting.

2

3

Upon finishing the setting, move the arrow to EXIT and press the TEST button.

SYSTEM ASSIGNMENTS

CABINET TYPE 1PLAYER(S) (A)
ADVERTISE SOUND ON (B)
MONITOR TYPE HORIZONTAL (C)
SERVICE TYPE COMMON (D)

-> EXIT

SELECT WITH SERVICE BUTTON
AND
PRESS TEST BUTTON

(A) CABINET TYPE (1PLAYER(S), 2PLAYER(S), 3PLAYER(S), 4PLAYER(S))

Sets the number of players between 1 and 4.
Fix setting to 1 PLAYER(S).

(B) ADVERTISE SOUND (ON, OFF)

Sets whether ADVERTISE sound is to be emitted or not.

(C) MONITOR TYPE (HORIZONTAL, VERTICAL)

Sets the on-screen display to the positional direction of monitor (HORIZONTAL/VERTICAL)
Fix setting to HORIZONTAL.
HORIZONTAL: Normal on-screen display
VERTICAL: On-screen display when the monitor is vertically positioned as against

normal HORIZONTAL position.

(D) SERVICE TYPE (COMMON, INDIVIDUAL)

Sets the functioning of when the SERVICE button is pressed, in case that several SERVICE
buttons exist.
Fix setting to COMMON.
COMMON: By pressing any SERVICE button, Service credit can be obtained for all

Players.

INDIVIDUAL: By pressing SERVICE button, Service credit can be obtained for the Player

corresponding to the SERVICE button pressed.

32

F. COIN ASSIGNMENTS

In this mode, the setting of incremental credit increase as against coin insertion can be changed.

1

Press the SERVICE button to move the arrow. Bring the arrow to the desired item.

2

Press the TEST button to change the setting.

Upon finishing the setting, bring the arrow to EXIT and press the TEST button.

3

COIN ASSIGNMENTS

COIN CHUTE TYPE COMMON (A)
COIN/CREDIT SETTING #1 (B)
COIN CHUTE #1
1 COIN 1 CREDIT

COIN CHUTE #2
1 COIN 1 CREDIT
(C)
(G)
MANUAL SETTING
SEQUENCE SETTING

->EXIT

SELECT WITH SERVICE BUTTON
AND PRESS TEST BUTTON

Setting to COMMON Setting to INDIVIDUAL

COIN ASSIGNMENTS

COIN CHUTE TYPE INDIVIDUAL
COIN/CREDIT SETTING #1
COIN CHUTE #1
1 COIN 1 CREDIT

MANUAL SETTING
SEQUENCE SETTING

->EXIT

SELECT WITH SERVICE BUTTON
AND PRESS TEST BUTTON

(A) COIN CHUTE TYPE (COMMON, INDIVIDUAL)

Fix setting to COMMON.

COMMON
This setting is for the cabinet which has a coin chute(s) for common use by plural players. Up
to 2 Coin Chutes (#1 and #2) can be used and also, (B) COIN/CREDIT SETTING ratio can be
set separately for #1 and #2.

INDIVIDUAL
This setting is for the cabinet in which each player uses an independent coin chute. Coins
inserted by each player are handled as the player's credits. Depending on the CABINET TYPE
setting in the SYSTEM ASSIGNMENTS and the functioning of the connected I/O Board, the
number of Coin SW INPUT ports varies between 1 and 4. (B) COIN/CREDIT SETTING ratio
is common for eath Coin Chute.

(B) COIN/CREDIT SETTING ( # 1 ~ # 27)

Sets the credit increase increment per coin insertion. There are 27 settings from #1 to #27,
expressed in

credit(s) as against coins inserted. #27 refers to FREE PLAY.

For details, refer to Table 1 (COMMON) and Table 2 (INDIVIDUAL).

33

(C) MANUAL SETTING

The Credit's incremental increase settings as against a coin insertion are shown in further details
than in (B) above (refer to Table 3). Also, note that when this MANUAL SETTING is
performed, (B) COIN CREDIT setting becomes ineffective.

MANUAL SETTING

COIN ASSIGNMENTS
MANUAL SETTING

COIN TO CREDIT 1 (D)
BONUS ADDER NO BONUS ADDER (E)
COIN CHUTE #1 MULTIPLIER
1 COIN COUNT AS 1 COIN
COIN 1 2 3 4 5 6 7 8 9
CREDIT 1 2 3 4 5 6 7 8 9

COIN CHUTE #2 MULTIPLIER
1 COIN COUNT AS 1 COIN
COIN 1 2 3 4 5 6 7 8 9
CREDIT 1 2 3 4 5 6 7 8 9

SEQUENCE SETTING (G)

->EXIT

SELECT WITH SERVICE BUTTON
AND PRESS TEST BUTTON

Setting to COMMON

(D) COIN TO CREDIT

Determines COIN/CREDIT setting.

COIN ASSIGNMENTS
MANUAL SETTING

COIN TO CREDIT 1
BONUS ADDER NO BONUS ADDER
COIN CHUTE MULTIPLIER
1 COIN COUNT AS 1 COIN
COIN 1 2 3 4 5 6 7 8 9
CREDIT 1 2 3 4 5 6 7 8 9

SEQUENCE SETTING

->EXIT

SELECT WITH SERVICE BUTTON
AND
PRESS TEST BUTTON

Setting to INDIVIDUAL

(E) BONUS ADDER

This sets how many coins should be inserted to obtain one SERVICE COIN.

(F) COIN CHUTE ( # 1 / # 2 ) MULTIPLIER

This sets how many tokens one coin represents.

34

Table 1: COIN/CREDIT SETTING (COIN CHUTE COMMON TYPE)

NAME OF SETTING COIN CHUTE 1 COIN CHUTE 2

SETTING #1 1 COIN 1 CREDIT 1 COIN 1 CREDIT
SETTING #2 1 COIN 2 CREDITS 1 COIN 1 CREDIT
SETTING #3 1 COIN 3 CREDITS 1 COIN 1 CREDIT
SETTING #4 1 COIN 4 CREDITS 1 COIN 1 CREDIT
SETTING #5 1 COIN 5 CREDITS 1 COIN 1 CREDIT
SETTING #6 1 COIN 2 CREDITS 1 COIN 2 CREDITS
SETTING #7 1 COIN 5 CREDITS 1 COIN 2 CREDITS
SETTING #8 1 COIN 3 CREDITS 1 COIN 3 CREDITS
SETTING #9 1 COIN 4 CREDITS 1 COIN 4 CREDITS
SETTING #10 1 COIN 5 CREDITS 1 COIN 5 CREDITS
SETTING #11 1 COIN 6 CREDITS 1 COIN 6 CREDITS
SETTING #12 2 COINS 1 CREDIT 2 COINS 1 CREDIT
SETTING #13 1 COIN 1 CREDIT 2 COINS 1 CREDIT
SETTING #14 1 COIN 2 CREDITS 2 COINS 1 CREDIT
SETTING #15 1 COIN 1 CREDIT 1 COIN 1 CREDIT

2 COINS 3 CREDITS 2 COINS 3 CREDITS

SETTING #16 1 COIN 3 CREDITS 1 COIN 1 CREDIT

SETTING #17 3 COINS 1 CREDIT 3 COINS 1 CREDIT
SETTING #18 4 COINS 1 CREDIT 4 COINS 1 CREDIT
SETTING #19 1 COIN 1 CREDIT 1 COIN 1 CREDIT

2 COINS 2 CREDITS 2 COINS 2 CREDITS
3 COINS 3 CREDITS 3 COINS 3 CREDITS
4 COINS 5 CREDITS 4 COINS 5 CREDITS

SETTING #20 1 COIN 5 CREDITS 1 COIN 1 CREDIT

SETTING #21 5 COINS 1 CREDIT 5 COINS 1 CREDIT
SETTING #22 1 COIN 2 CREDITS 3 COINS 1 CREDIT

SETTING #23 2 COINS 1 CREDIT 2 COINS 1 CREDIT

4 COINS 2 CREDITS 4 COINS 2 CREDITS
5 COINS 3 CREDITS 5 COINS 3 CREDITS

SETTING #24 1 COIN 3 CREDITS 2 COINS 1 CREDIT

SETTING #25 1 COIN 1 CREDIT 1 COIN 1 CREDIT

2 COINS 2 CREDITS 2 COINS 2 CREDITS
3 COINS 3 CREDITS 3 COINS 3 CREDITS
4 COINS 4 CREDITS 4 COINS 4 CREDITS
5 COINS 6 CREDITS 5 COINS 6 CREDITS

SETTING #26 1 COIN 6 CREDITS 1 COIN 1 CREDIT

SETTING #27 FREE PLAY FREE PLAY

2 COINS 3 CREDITS

2 COINS 2 CREDITS
3 COINS 3 CREDITS
4 COINS 5 CREDITS

5 COINS 2 CREDITS

4 COINS 2 CREDITS
5 COINS 3 CREDITS

2 COINS 2 CREDITS
3 COINS 3 CREDITS
4 COINS 4 CREDITS
5 COINS 6 CREDITS

35

Table 2: COIN/CREDIT SETTING (COIN CHUTE INDIVIDUAL TYPE)

NAME OF SETTING
SETTING #1 1 COIN 1 CREDIT
SETTING #2 1 COIN 2 CREDITS
SETTING #3 1 COIN 3 CREDITS
SETTING #4 1 COIN 4 CREDITS
SETTING #5 1 COIN 5 CREDITS
SETTING #11 1 COIN 6 CREDITS
SETTING #12 2 COINS 1 CREDIT
SETTING #15 1 COIN 1 CREDIT

SETTING #17 3 COINS 1 CREDIT
SETTING #18 4 COINS 1 CREDIT
SETTING #19 1 COIN 1 CREDIT

Table 3: MANUAL SETTING

EACH SEAT'S COIN CHUTE

2 COINS 3 CREDITS

2 COINS 2 CREDITS
3 COINS 3 CREDITS
4 COINS 5 CREDITS

NAME OF SETTING
SETTING #21 5 COINS 1 CREDIT
SETTING #23 2 COINS 1 CREDIT

SETTING #25 1 COIN 1 CREDIT

SETTING #27 FREE PLAY

EACH SEAT'S COIN CHUTE

4 COINS 2 CREDITS
5 COINS 3 CREDITS

2 COINS 2 CREDITS
3 COINS 3 CREDITS
4 COINS 4 CREDITS
5 COINS 6 CREDITS

COIN TO CREDIT 1 COIN 1 CREDIT

2 COINS 1 CREDIT
3 COINS 1 CREDIT
4 COINS 1 CREDIT
5 COINS 1 CREDIT
6 COINS 1 CREDIT
7 COINS 1 CREDIT
8 COINS 1 CREDIT
9 COINS 1 CREDIT

BONUS ADDER NO BONUS ADDER

2 COINS GIVE 1 EXTRA COIN
3 COINS GIVE 1 EXTRA COIN
4 COINS GIVE 1 EXTRA COIN
5 COINS GIVE 1 EXTRA COIN
6 COINS GIVE 1 EXTRA COIN
7 COINS GIVE 1 EXTRA COIN
8 COINS GIVE 1 EXTRA COIN
9 COINS GIVE 1 EXTRA COIN

COIN CHUTE (# 1 / # 2) 1 COIN COUNTS AS 1 COIN
MULTIPLIER 1 COIN COUNTS AS 2 COINS

1 COIN COUNTS AS 3 COINS
1 COIN COUNTS AS 4 COINS
1 COIN COUNTS AS 5 COINS
1 COIN COUNTS AS 6 COINS
1 COIN COUNTS AS 7 COINS
1 COIN COUNTS AS 8 COINS
1 COIN COUNTS AS 9 COINS

36

(G) SEQUENCE SETTING

Number of credits required for starting game, etc. can be set.
Function varies depending on the specific games. To find out what kind of functions are
allotted to each sequence, or what is the initial value for each sequence, refer to the Instruction
Manual of the game connected. Each sequence can be set between 1 ~ 5 credit(s).

COIN ASSIGNMENTS
SEQUENCE SETTING

SEQUENCE 1 1 CREDIT(S)
SEQUENCE 2 1 CREDIT(S)
SEQUENCE 3 1 CREDIT(S)
SEQUENCE 4 1 CREDIT(S)
SEQUENCE 5 1 CREDIT(S)
SEQUENCE 6 1 CREDIT(S)
SEQUENCE 7 1 CREDIT(S)
SEQUENCE 8 1 CREDIT(S)

-> EXIT
[WILD RIDERS XXXXXXXXXX]
DESCRIPTION OF SEQUENCE
1 CREDIT TO START
2 NO USE
3 NO USE
4 NO USE
5 NO USE
6 NO USE
7 NO USE
8 NO USE

SELECT WITH SERVICE BUTTON
AND
PRESS TEST BUTTON

In cases of video games such as WILD RIDERS. :
SEQUENCE 1 : Number of credits required for game start (initial value=1)
SEQUENCE 2 ~ 8 : NOT USED.

37

G. BOOKKEEPING

• BOOKKEEPING 1/2
This allows such data as operating time/No. of coins inserted/ No. of credits to be checked.

BOOKKEEPING 1/2

TOTAL TIME
0D 00H 00M 00S

CREDIT 0

COIN 1 0
COIN 2 0
COIN 3 0
COIN 4 0

TOTAL COIN 0
COIN CREDIT 0
SERVICE CREDIT 0
TOTAL CREDIT 0

PRESS TEST BUTTON TO CONTINUE

Press the TEST button to proceed to BOOKKEEPING 2/2.

• BOOKKEEPING 2/2
Each sequence displays the frequency of functioning.

BOOKKEEPING 2/2

P1 SEQ 1 0
P1 SEQ 2 0
P1 SEQ 3 0
P1 SEQ 4 0
P1 SEQ 5 0
P1 SEQ 6 0
P1 SEQ 7 0
P1 SEQ 8 0

PRESS TEST BUTTON TO EXIT

In cases of video games such as WILD RIDERS. :
P1 SEQ 1 : Play frequency of Player 1
P1 SEQ 2 ~ 8 : NOT USED.

38

H. BACKUP DATA CLEAR

Clears the contents of BOOKKEEPING.

BACKUP DATA CLEAR

YES(CLEAR)

-> NO(CANCEL)

SELECT WITH SERVICE BUTTON
AND PRESS TEST BUTTON

When clearing, bring the arrow to YES by using the SERVICE button and press the TEST
button. Bring the arrow to NO and press the TEST button to have the menu mode return
without clearing the data. COMPLETED is displayed when clearing is completed. Press the
TEST button to return to the menu mode.

I. CLOCK SETTING

Set YEAR, MONTH, DAY, HOUR, and MINUTE for NAOMI 2 Main BD.

Select the desired item with the SERVICE button and press the TEST button to increase
the value. Upon finishing the SETTING, bring the arrow to EXIT and press the TEST
button to return to the menu mode.

CLOCK SETTING

1998 12/02 14:30 33 WED

YEAR
MONTH
DAY
HOUR
MINUTE

-> EXIT

SELECT WITH SERVICE BUTTON
AND PRESS TEST BUTTON

39

J. ROM BOARD TEST

In this test, on-ROM-BD ROM check is executed.
If GOOD is displayed below RESULT, it is satisfactory.
BYTE and WORD refers to the check sum of each unit.

GAME ROM TEST
[XXXXXX

NO. TYPE RESULT BYTE WORD
IC22 16M ---- 0123 4567
IC1 64M GOOD 0123 4567
IC2 64M GOOD 0123 4567
IC3 64M GOOD 0123 4567
IC4 64M GOOD 0123 4567
IC5 64M GOOD 0123 4567
IC6 64M GOOD 0123 4567
IC7 64M GOOD 0123 4567
IC8 64M GOOD 0123 4567
IC9 64M GOOD 0123 4567
IC10 64M GOOD 0123 4567
:
IC20 64M GOOD 0123 4567

PRESS TEST BUTTON TO EXIT

XXXXXXX

]

Program ROMs (IC22) do not display GOOD or BAD.
Press the TEST button to return to the menu mode.

K. GAME TEST MODE

Enters the TEST mode of the game connected. The TEST mode includes INPUT test, GAME
ASSIGNMENTS such as game difficulty and others, BOOKKEEPING, etc. Depending on
specific games, necessary items are added and unnecessary items removed. As such, the
contents thereof may be changed.

40

8 - 3 GAME TEST MODE

A. SETTING THE CARD

Be sure to use dedicated cards available for this product (i.e., 601-11051).
Use of one other than such dedicated cards may cause a malfunction or failure of the
machine.

Be sure to set the specified number of cards in the specified orientation by using the
specified procedure. Wrong setting of the cards may cause the machine to fail.

This machine allows you to set upt ot 100 cards at a time. You must not set over 100
cards at a time. If you do so, a trouble such as card jamming may occur.

Set virgin cards taken out from a container that was unpacked immediately before use.
Use of any deformed or deteriorated card may cause trouble.

Do not include a corrugated, bent, or used card in the card deck.

The card reader/writer is located on the top of the coin chute tower. Place the cards on the card
reader/writer.

• Unlock and open the cover to find the card reader/writer. The dispenser on which you should

place the cards is located at the rear of the reader/writer.

• From the car reader/writer, take out the dispenser upward in a straight line.

• Remove the cover from the back of the dispenser.

• Place the cards into the dispenser according to the instructions on the sticker annexed to the

dispenser. There is no print face on a card of the Club Kart. Determine the card in reference to
the inserting direction mark located at corners of the cards. Do not confuse the top/bottom or
direction.

• Reinstall the cover to the dispenser.

• Insert the dispenser into the card reader/writer. The dispenser can be inserted only in the

predetermined orientation.

• Close and lock the cover.

41

B. TURNING ON THE POWER

Turn on th AC unit’s main switch to supply power to the unit. Once power is turned on, the flourescent lamp
in the bill board lights up. The Start System Screen displays after a lapse of several seconds. It is followed
by the screen that indicates that the network is currently being checked if the communication mode has been
set. If there is a bad or improper communication connection, each screen will not proceed to the next,
remaining on the currently network-checked sreen. If this occurs, resolve the error according to the
instructions in this document.
If the communication mode has not been set or the communication check ends normally, the Motor Check
Screen returns. While the Motor Check Screen is on-screen, the steering wheel can move either clockwise or
counterclockwise. If you touch the wheel, the motor check is hindered and the game will not operate
normally. So, you must not touch it at this time. Failures are displayed, if found. Resolve the errors
according to the instructions in this document. Pressing the Start button while a failure is on-screen allows
you to go to the next screen and start the game without reaction.
Next the Check Card Reader/Writer Screen displays. If cleaning is required or a failure is found, this is
indicated on the screen. In this case, resolve the error according to the instructions in this document.
Once all the above steps have been completed, the Advertise Screen displays and voices are output through
the left and right loudspeakers, unless you have set the machine so that no voices are output during the
Advertise mode.
This product retains the number of credits and the ranking data even after the power is turned off. It does not
retain data about the fractional number of coins (i.e., the number of coins not reaching one credit) or the
bonus adder count.

C. CARD READER/WRITER

Take care if you work with the machine, without turning the power, in an attempt to return
to the game. In the alive state, the machine may operate suddenly, causing your finger to
be pinched or cut.

If a trouble such as card jamming occurs on the card reader/writer, you are notified of the trouble
on the screen. You cannot proceed to a play unless you resolve the trouble at this time. First
identify the trouble before you begin to take action.
When all cards are used up, you can no longer issue a new card, with the message “Now new
Club Kart Card” cannot be created” on-screen, instead of a trouble indication.

To obtain the dedicated or cleaning cards, place an order to the contact point or the dealer from
which you purchased the product. In the order form, write down the card name and the amount
of cards.
With each of the following part numbers, you can purchase 200 dedicated and 30 cleaning cards.

Dedicated Card

Part number: 601-11051
Name: CARD PACKAGE CKT

Cleaning Card

Part number: 601-11050
Name: CLEANING KIT

42

1) Action in Operation

The game board of this product backs up the data only when the card reader/writer detects a
trouble DURING OPERATION and the Error Screen displays. However, no written data is
backed up in the following cases:

• An action deemed to be illegal was detected while the game or write was in operation.

If backed up data remains when the power is turned on, the Check Card Reader/Writer Screen will
be replaced with the Save Data screen. The backed up data is cleared in the following cases:

• After an action was taken against a trouble, normal write ended.

• The backed up data was cleared in the Game Test Mode.

• Data save taking place at power-on time was canceled, and the succeeding game ended.

If the card reader/writer has not been set as being unused, you will be unable to select any game
mode with use of cards while the game will be in progress.
Thus, for the card reader/writer, deal with the player, paying attention to the following points:

• When a trouble occurs during write operation, the retained data can be written for proceeding to

the game by resolving the trouble without turning on the power. If you resolved the trouble with
power off, write the data according to the instructions on the screen when you attempt to turn on
the power.

• Even if the player request the system for use of cards when you have set the machine so that the

card reader/writer is not used, the request is rejected because of the nature of the system.

2) Setting the Card

Be sure to use dedicated cards available for this product (i.e., 601-11051).
Use of ones other than such dedicated cards may cause a malfunction or failure of the
machine.

Be sure to set the specified number of card in the specified orientation by using the
specified procedure. Wrong setting of the cards may cause the machine to fail.

This machine allows you to set up to 100 cards at a time. You must not set over 100
cards at a time. If you do so, a trouble such as card jamming may occur.

Set virgin cards taken out from a container that was unpacked immediately before use.
Use of any deformed or deteriorated card may cause a trouble.

The card reader/writer is located on the top of the coin chute tower. Place the cards on the card
reader/writer. Card setting is enabled with power either on or off.

• Unlock and open the cover to find the card reader/writer.

The dispenser on which you should place the cards is located at the rear of the reader/writer.

• From the card reader/writer, take out the dispenser upward in a straight line.

• Remove the cover from the back of the dispenser.

• Place the cards into the dispenser according to the instructions on the sticker annexed to the

dispenser. There is no print face on a card of the Club Kart. Determine the card in reference to
the inserting direction mark located at corners of the cards. Do not confuse the top/bottom or
direction.

• Reinstall the cover to the dispenser.

• Insert the dispenser into the card reader/writer. The dispenser can be inserted only in the

predetermined orientation.

• Close and lock the cover.

43

3) Head Cleaning

If the head cleaning mode is entered while the power is on, use the head cleaning
procedure according to the instructions on the screen. The head cleaning mode cannot
be quitted for being ready for starting the game unless the head cleaning is completed.

Be sure to use dedicated cleaning cards (i.e., 601-11050). Use of ones other than such
dedicated cleaning cards may cause a malfunction or failure of the machine.

Cleaning cards are disposable. They must not be used more than once.

Use each cleaning card immediately after it is taken out from an unsealed package.
Dried cards are ineffective for cleaning.

Never use a cleaning procedure not described in this document. Use of it may cause a
malfunction or failure of the machine.

This product memorizes the count you use the card reader/writer. When the power is turned off
and on after the count of use exceeds 100, the head cleaning mode is entered while the Check
Card Reader/Writer Screen is on-screen after you turn on the power. At this time, using a dedi­cated cleaning card, use the cleaning card procedure according to the instructions on the screen.
The head cleaning mode cannot be quitted for being ready for starting the game unless the head
cleaning is completed. You can use the Test Mode to perform the head cleaning mechanism
assembly. For details, see the “Test Mode” section in this document.

Start the cleaning clears the count of use above.

• Insert the cleaning card into the slot according to the instructions on the screen. The card is

retracted automatically.

• A screen displays that shows that cleaning is in progress.

• Once the cleaning is completed, the cleaning card is ejected from the slot. Take out the cleaning

card.

Cleaning Card Reader/Writer Screen

CARD R/W

PLEASE INSERT CLEANING CARD

CLEANING

PRESS START TO CANCEL

Insert the cleaning card into the slot.
Now cleaning. Wait for a minute.
Cleaning is complete. Take out the card.
You cannot proceed to the next step until you take it out.

44

4) Takin Action Against Card Jamming

If card jamming occurs, the error is shown on the screen. Use the procedure to take action against
the trouble:

• Unlock and open the cover.

• Unlock the hatch by drawing the green shaft attached to the top cover on the card reader/writer.

While drawing the shaft, open the cover up.

• Remove the card jammed in the card reader/writer.

• While drawing the shaft, close the cover. With the top cover closed, release the green shaft.

Check that the top cover has been locked securely.

Forcible Cleaning

This product memorizes the count you use the card reader/writer. When the power is turned off
and on after the count of use exceeds 100, the head cleaning mode is entered while the Check
Card Reader/Writer Screen is on-screen after you turn on the power. The head cleaning mode
cannot be quitted for being ready for starting the game unless the head cleaning is completed.
When the card reader/writer is subjected to head cleaning, the count of use is cleared and the the
mode ends.
At this time, using a dedicated cleaning card, use the cleaning card procedure according to the
instructions on the screen.
The count of use above is cleared also when the Test Mode is used for head cleaning.

Cleaning Card Reader/Writer Screen

CARD R/W

PLEASE INSERT CLEANING CARD

• Insert the cleaning card into the slot. The card is retracted automatically.

• Now cleaning. Wait for a minute.

• Cleaning is complete. Take out the card. You cannot proceed to the next step until you take it

CLEANING

out.

45

D. REWRITING DATA ONTO THE CARD

The game board of this product backs up the data only when the card reader/writer detects a trouble DURING
OPERATION and the Error Screen displays. However, no written data is backed up in the following case:

• An action deemed to be illegal was detected while the game or write was in operation.

If backed up data remains when the power is turned on the Check Card Reader/Writer Screen will be replaced
with the Save Data screen. Once written onto the cord, the backed up data is cleared before the mode ends.

Write the data onto the desired card according to the instructions on the screen.
You can use the Start button to cancel the write.
The backed up data is cleared in the following cases:

• Normal write ended.

• The backed up data was cleared in the Game Test Mode.

• Data save taking place at power-on time was canceled, and the succeeding game ended.

Rewrite Data Onto Card Screen

CARD R/W

PLEASE INSERT CARD

PRESS START TO CANCEL

• Insert the cleaning card into the slot. The card is retracted automatically.

• Now writing data. Wait for a minute.

• Data write is complete. Take out the card. You cannot proceed to the next step until you take it out.

DATA SAVE

46

E. CARD LOW LEVEL ADJUSTMENT

• Your game is equipped with a card “Low Level” system. It consists of a screw that moves with the

magazine as cards are dispensed. When the screw gets low enough, the beam is interrupted and the LED is
illuminated.

Added tape creates a flag to break beam sooner.

Low Level LED

• Current configuration provides notification at approximately 10 card (+/- 2). If you feel you need sooner

notification, see the diagram for suggested adjustment method.

47

E. TROUBLESHOOTING

Card Reader/Writer Trouble

When a card reader/writer failure is detected while the game is in progress, the error type is shown on the
screen. Take the appropriate error according to the actions listed below.
The game board of this product backs up the data only when the card reader/writer detects a trouble DURING
OPERATION and the Error Screen displays. However, no written data is backed up in the following case:

• An action deemed to be illegal was detected while the game or write was in operation.

If backed up data remains when the power is turned on, the Check Card Reader/Writer Screen will be
replaced with the Save Data screen. The backed up data is cleared in the following cases:

• After an action was taken against a trouble, normal write ended.

• The backed up data was cleared in the Game Test Mode.

• Data save taking place at power-on time was canceled, and the succeeding game ended.

Error

• Error condition • Action

“CONNECTION ERROR”

Reader/ Writer Communication Error - Check the connection cables and then turn on the power again.

“MECHANIC ERROR1”

DC Motor/Encoder Error - Check the connection cables and then turn on the power again. (Note 1)

“MECHANIC ERROR2”

Thermal Head Elevation Error - Check the connection cables and then turn on the power again.
(Note 1)

“CARD STUFFED”

Card Jamming - Remove the card jam. (Note 2)

“MECHANIC ERROR3”

Abnormal Temperature of Thermal Head - Check the connection cables and then turn on the power
again. (Note 1)

“CARD EMPTY”

Hopper Card Not Found - Supply card to the hopper. (Note 2)

“DRAW CARD ERROR”

Error in Taking Out from the Hopper - Remove the card jame and check the hopper. (Note 2)

“CAN’T SAVE”

No Data Can Be Written onto the Card. (Note 3)

“UNKNOWN ERROR”

Error Other Than Above - Check the connection cables and then turn on the power again.

“SCIF ERROR”

SCIF Error - Check the connection cables.

48

Note 1: If this error reappears frequently, the card reader/writer body may be faulty.
Note 2: After the action has been taken, press the Start button before you follow the instructions on the error
screen. Now you can return to the game.
Note 3: If the same error repeats again and again, clean the card reader/writer. If no data can still be written,
the card reader/writer body may be faulty.

Without entering the Test Mode, turn on the power, again, to the cabinet if the following is included in the
“Action” column in the above table: “turn on the power again.”

If the error is not included in the “Error” column in the above table, merely turn on the power again.

If no improvments result from the appropriate action listed in this document, contact one of the contact points
listed in this document or the dealer from which you purchased the product.

Reaction Motor Trouble

When a failure is detected on the Check Motor Screen, which appears when the power is turned on.
Use the following procedure to take action:

Error Display 1

STEERING DRIVE BD. IS NOT CONNECTED

PRESS START TO CANCEL

PRESS VIEW TO RETRY

OR

This is an error in communication between NAOMI 2 and the motor driver. Check the wiring.
Pressing the Start button starts the game without steering-wheel reaction.
Pressing the View button reinitiates the machine.

Error Display 2

STEERING DRIVE BD. DOES NOT WORK

PRESS START BUTTON TO CONTINUE

WITHOUT REACTION FORCE

49

This is an error that occurs when the motor could not be initialized properly. Check the wiring between the
driver motors.
Pressing the start button starts the game without steering-wheel reaction.

When a failure is detected while the game is in progress, it continues to operate until it ends.

After the game ends, you are brought to the same screen as Check Motor that appeared at power-on time. If a
failure is detected at this time, Error Display 2, above, appears. Take action against it. Usually, the encoder
annexed to the motor is used for detection of the steering wheel; however, it will be unavailable if a failure is
detected on the motor. The handle mechanism is provided with a spare volume for this reason. When the
handle center is set with Set Volume Control Screen in the Test Mode, volume center setting, as well as
encoder setting, takes place. However, when you make the machine operate without reaction because of a
motor failure, center the volume control again by way of precaution.

50

F. GAME MENU

The new settings will not take effect until the Game Test Mode is exited. When

you make change to the settings, exit the Game Test Mode by proper operation.

You must not attempt to demonstrate this game (for the selling purpose) with any
other than those specified in this document. Use of such settings may cause mal­functions or bad operation on the machine.

SYSTEM MENU

RAM TEST
JVS TEST
SOUND TEST
C.R.T. TEST
SYSTEM ASSIGNMENTS
COIN ASSIGNMENTS
BOOKKEEPING
BACKUP DATA CLEAR
CLOCK SETTING

ROM BOARD TEST
GAME TEST MODE
[XXXXXXXXXXXXXXX]

-> EXIT

SELECT WITH SERVICE BUTTON
AND PRESS TEST BUTTON

GAME TEST MENU

INPUT TEST
OUTPUT TEST
GAME SETTING
VOLUME SETTING
CARD R/W TEST
BOOKKEEPING
BACKUP DATA CLEAR
> EXIT

SELECT WITH SERVICE BUTTON
AND
PRESS TEST BUTTON

Pressing the SERVICE button moves the arrow on the screen. Move the arrow to select the
item you want to run. Pressing the TEST button runs the currently selected item. The screen
changes to the one for that item, and you can change or adjust the settings.
Select EXIT and press the TEST button to return to the System Test Menu Screen.

51

G. INPUT TEST

By selecting INPUT TEST on the Menu Screen and pressing the Test button, the
steering wheel is centered automatically as done when the machine is started. To
protect persons from accidents make sure that nobody is in contact with the steering
wheel before pressing the TEST button.

To prevent accidents, breakage of parts, and malfunctions, do not touch the
steering wheel until centering of the steering wheel is completed.

INPUT TEST tests the input devices. Using this screen, check the input devices
periodically.
Operate each input device. If the display at the right of the appropriate device changes
from OFF to ON, it is diagnosed as being normal.
Check that each of the indications at the right of STEERING, ACCEL, and BRAKE
change smoothly in response to operations of each of the input devices.

INPUT TEST

STEERING WHEEL: ****
ACCEL. : ****
BRAKE : ****

VIEW SW : OFF
START SW : OFF

PRESS TEST AND SERVICE BUTTON TO EXIT

Pressing the TEST button returns you to the Game Test Menu Screen.

VOLUME CONTROL RECOMMENDED SETTINGS

• Steering wheel: Centered (when traveling in a straight line) 2000H

• Accelerator:
When the pedal is released 30H
When the pedal is pressed fully C0H

• Brake:
When the pedal is released 30H
When the pedal is pressed fully C0H

52

H. OUTPUT TEST

You can monitor the state of the lights. Use this screen to check the lights periodically.

OUTPUT TEST

START LAMP OFF
VIEW LAMP OFF
> EXIT

SELECT WITH SERVICE BUTTON

PRESS TEST BUTTON

AND

Pressing the SERVICE button moves the arrow. With the arrow aligned with the tested lamp
item, press the TEST button.
If the lamp lights up when the indication at the right of each name is ON and goes out when it is
OFF, this lamp and wiring connections are normal.
By selecting EXIT and pressing the TEST button, you return to the Game Test Menu Screen.

53

I. GAME SETTING

You can make the settings about cabinet operations such as the communicated mode or the
reaction force of the steering wheel.

MAKING CHANGE TO THE SETTINGS

1. By pressing the SERVICE button, move the arrow (>) to the desired item to change.

2. Pressing the Test button changes the display at the right of the currently selected item.

Change the item to the desired display.

3. Press the SERVICE button to select EXIT. Then press the TEST button. This returns you

to the Game Test Menu Screen.

GAME SETTING

LINK TYPE: XXXXXX

STEERING POWER: ****************

STEERING DIR. : REVERSE

CARD SYSTEM: ENABLE

BONUS GAMES: 0

> EXIT

AND
PRESS TEST BUTTON

SELECT WITH SERVICE BUTTON

LINK TYPE: Used for settings of communicated play. You have four options:

MASTER, SLAVE, SATELLITE, and STAND-ALONE. If you
want to enjoy the game alone, set to STAND-ALONE. Setting for
communicatedplay, be sure to set MASTER for only one machine,
or seat, and set SLAVE for all the remaining ones. SATELLITE is
a setting for a relay monitor.

STEERING POWER: Sets reaction for the steering wheel. Increase or decrease in the

number of asterisks (*) is reflected to the reaction force. The more
the asterisks, the reaction force the larger.

STEERING DIR.: Sets steering reaction direction. Default for deluxe game is

REVERSE.

CARD SYSTEM: Activates card reader system.
BONUS GAMES: Choose 0-3.

54

J. VOLUME SETTING

By setting VOLUME SETTING on the Menu Screen and pressing the TEST
button, the steering wheel is centered automatically as done when the machine is
started. To protect persons from accidents, make sure that nobody is in contact with
the steering wheel, before pressing the TEST button.

To prevent accidents, breakage of parts, and malfunctions, do not touch the
steering wheel until centering of the steering wheel is completed.

No normal play is guaranteed unless all the input devices are set properly.
Be sure to makethe proper settings before you begin demonstration for the selling
purpose.

Once you have completed change to the settings, select EXT and press the TEST
button. The new settings will not take effect until this mode is exited.

By setting the VOLUME SETTING on the Menu Screen and pressing the Test button,
centering of the steering wheel in initiated automatically. After the centering is com­pleted, you can use the screen below to make the steering wheel, accelerator, and brake
settings.
If the operability of the steering wheel, accelerator, or brake is poor, use this screen to
make the proper settings for the volume control.

VOLUME SETTING

[2000] 2000
STEER: *---------------------------------------------

[2000]3000 C000
ACCEL: ----*-------------------------*--------------

[8100]3000 C000
BRAKE: ----*-------------------------*-------------

> EXIT

SELECT WITH SERVICE BUTTON
AND
PRESS TEST BUTTON

MIN MID MAX

1. By moving the SERVICE button to move the arrow, select the input device for which you
want to make settings.

2. For either the accelerator or brake, press START without pressing the pedal. Set the value
resulting when you release it.

3. With the pedal pressed fully, press START to set the value resulting when you press it fully.

4. For the steering wheel, press START while supporting it along the straight line.

5. Select EXIT and press the TEST button.
The setting changes are not updated until you select EXIT. After you make change to the

settings, be sure to select EXIT.

By selecting EXIT and pressing the TEST button, you return to the Game Test Menu Screen.

55

K. CARD R/W TEST

Check operation of the card reader/writer (R/W) and clean it periodically.

This screen lets you check operation of the card reader/writer (R/W) or clean it.

CARD R/W TEST

CARD R/W STATUS: *******

> EXIT

SELECT WITH SERVICE BUTTON
AND
PRESS TEST BUTTON

INFORMATION

INITIALIZE
CLEANING
CHECK R/W: ---

The arrow can move to the following items:

• INITIALIZE: Initialization

• CLEANING: Cleaning

• CHECK R/W: R/W Operation Check

Depending on the R/W running mode, one of the following is displayed in “ *****” in “CARD R/W
STATUS: *****” :

READY Now waiting (Clear to Send Command)
INITIAL Now initializing (Not Clear to Send Command)
CLEAN Now cleaning (Not Clear to Send Command)
GET Cards are being taken out from the hopper (Not Clear to Send Command)
SAVE Sample data is saved onto the card (Not Clear to Send Command)
LOAD Load card data and compares it with sample data (Not Clear to Send Command)
OUT Eject cards (Not Clear to Send Command)
ERROR Error ( Clear to Initialize Command Only)

While a status with a note of “Not Clear to Send Command” in parentheses is on-screen, no operations are
accepted. If such a status has occured, wait until the operation in that status stops automatically and the
display comes to READY.
Should you need to cancel the operation forcibly, turn off the power. If you cancel it forcibly, be sure to
select and run INITIALIZE after turning on the power.

Occasionally, the “INFORMATION” field on the screen outputs one of the instructions below, although it
usually contains nothing.

56

While cleaning is in progress, waiting in the ready mode for inserting a cleaning card:

----- PLEASE INSERT CLEANING CARD -----

After the operation check, waiting for the ready mode for ejecting the card:

----- PLEASE REMOVE CARD -----

When an error occurs, its type is displayed in the “INFORMATION” field:

CONNECTION ERROR Connection Error
MECHANIC ERROR 1 DC Motor / Encoder Error
MECHANIC ERROR 2 Thermal Head Elevation Error
CARD STUFFED Card Jamming
MECHANIC ERROR 3 AbnormalTemperature of Thermal Head
CARD EMPTY Hopper Card Empty
DRAW CARD ERROR Error in Taking Card from Hopper
CAN’T SAVE Data cannot be written onto the card.
UNKNOWN ERROR Unknown Error
SCIF ERROR RC-232C Communication Error
NO ERROR No Error

The “---” field in “CHECK R/W: ---” shows the result of the operation check.

--- Not Checked
OK No Failure
NG Failure

The operation check takes out each card from the hopper, and writes the sample data onto it. The check
whether the read data matches the sample data. Then, the check ejects the card. When you draw out the
card at this time, the entire process of the check is completed.

CHECKING R/W OPERATION

1. Select “CHECK R/W” and press the TEST button.

R/W operates automatically as follows:

2. Takes out the card from the hopper: GET is displayed.

3. Saves the sample data onto the card: SAVE is displayed.

4. Loads the data on the card for comparison with the sample data: LOAD is displayed.

5. Ejects the card: OUT is displayed.

6. Draws out the card. Now the entire process of the check is completed.

If execution of the operation check results in display of NG, check the error condition. If you can take
action against the error, execute the operation check again after you take the proper action. If you cannot
take action against the error, repeat the check several times. If the result of the check is still NG, clean the
R/W.
If the subsequent execution of the operation check still results in NG, the R/W may be faulty.

If an error occurs, it is cleared by executing the INITIALIZE command. Note that when an error has

occured, the R/W only accepts this command (except EXIT).

57

CLEANING PROCEDURE

1. Select “CLEANING” and press the TEST button.

The following message appears to show that the R/W is ready for insertion of the cleaning card:

---PLEASE INSERT CLEANING CARD---

2. Insert the cleaning card into the R/W. On the screen, the status display is replaced with “CLEAN”, and
cleaning begins.

3. Once cleaning ends after a lapse of a certain time, the R/W automatically ejects the card. The status
display changes from “CLEAN” to “OUT.”

58

L. BOOKKEEPING

In four pages, this screen lists the data about the operation status up to now. Pressing the TEST
button brings you to the next page of the screen. When you press the TEST button on Page 4/4
of the screen, you return to the Game Test Menu.

BOOKKEEPING 1/4

NUMBER OF GAMES 0
NUMBER OF CARD GAMES 0
NUMBER OF NEW CARDS 0

PLAY TIME OD OH OM OS
AVERAGE PLAY TIME OH OM OS
LONGEST PLAY TIME OH OM OS
SHORTEST PLAY TIME OH OM OS

SELECT WITH SERVICE BUTTON

AND PRESS TEST BUTTON

NUMBER OF GAMES: Number of games played.

NUMBER OF CARD GAMES: Number of games played with cards.

NUMBER OF NEW CARDS: Number of games played with cards.

PLAY TIME: Time played.

59

BOOKKEEPING 2/4

TIME HISTOGRAM

OM00S - OM29S 0
OM30S - OM59S 0
1MOOS - 1M29S 0
1M30S - 1M59S 0
2M00S - 2M29S 0
2M30S - 2M59S 0
3MOOS - 3M29S 0
3M30S - 3M59S 0
4M00S - 4M29S 0
4M30S - 4M59S 0
OVER - 5MOOS 0

SELECT WITH SERVICE BUTTON

AND PRESS TEST BUTTON

T IME HISTOGRAM lists the number of plays for each of the play times.

BOOKKEEPING 3/4

PLAYS/CLASS

RENTAL BEGINNER *
RENTAL NORMAL *
CLASS NOVICE *
CLASS B *
CLASS A *
CLASS S *
CLASS SS *
CLASS SSS *

SELECT WITH SERVICE BUTTON

AND PRESS TEST BUTTON

PLAY/CLASS shows the count of plays by class.

60

BOOKKEEPING 4/4

PLAYS/COURSE

1-A *
1-B *
1-C *
2-A *
2-B *
2-C *
3-A *
3-B *
3-C *
4-A *
4-B *
4-C *

SELECT WITH SERVICE BUTTON

AND PRESS TEST BUTTON

The PLAYS/COURSE Screen lists the count of plays by course. Pressing the TEST button
returns you to the Game Test Menu Screen.

61

M. BACKUP DATA CLEAR

BACKUP DATA CLEAR deletes data on the Bookkeeping Screen. To delete data about the
coins/credits, run BACKUP DATA CLEAR in the System Test Mode. Clearing the data does
not influence any data settings (except the data).

BACKUP DATA CLEAR

YES (CLEAR)
> NO (CANCEL)

SELECT WITH SERVICE BUTTON
AND
PRESS TEST BUTTON

To delete the data, use the SERVICE button to align the arrow with CLEAR and press the
TEST button. Once the data is deleted, this screen displays “COMPLETED.”
Pressing the TEST button again returns you to the Menu Screen. If you choose not to delete the
data, press the TEST button with the arrow aligned with NO. This returns you to the Menu
Screen.

62

9. CONTROL PANEL (STEERING MOTOR UNIT)

Before starting to work, ensure that the Power SW is OFF. Failure to observe
this can cause electric shock or short circuit.
Use care so as not to damage wirings. Damaged wiring can cause electric
shock or short circuit.
Do not touch undesignated places. Touching places not designated can cause
electric shock or short circuit.
This work should be performed by the Location's Maintenance Man or
Serviceman. Performing work by non-technical personnel can cause electric
shock hazard.

Do not insert hand into the mechanism so as not to cause hand and fingers

pinched in. Failure to observe this can cause a serious injury such as a
fracture.

When performing work such as parts replacement other than those specified in

this manual, be sure to contact where you purchased the product from and
confirm the work procedures and obtain precautions prior to performing work.
Inappropriate parts replacement and/or installing with erroneous adjustment
can cause an overload or the parts to come into contact, resulting in an electric
shock, a short circuit, and a fire.

9 - 1 ADJUSTING OR REPLACING THE V.R.

In cases the Steering operability is poor and the adjustment of VOLUME SETTING in the
TEST mode is ineffective, the causes may be the Volume Gear's mesh failure and or Volume
malfunctioning. By using the following procedure, adjust Volume gear mesh, or replace the
Volume. In this product, when the Steering Wheel is moved fully left/right, if the Volume shaft
is rotating within the movable range, the Volume is not feared to be damaged. Secure the
Volume in the manner the Volume shaft is oriented as shown and the gears are appropriately
engaged when the steering wheel is in the centering position allowing the car to go straight
forward.

ADJUSTING THE VOLUME

Prepare a Phillips screwdriver and a
wrench for M8 hexagonal nut.

1

Turn off power.

Remove the 6 Trusshead screws and

2

open the back of the main cabinet.

63

3

The V.R. is on the VR BASE (a white, plastic made part). Loosen the 2 screws which secure
the VR BASE and adjust the angle and appropriateness of gear mesh by moving the VR BASE.

Adjust to an appropriate mesh by securing the Steering Wheel in the direction allowing the car

4

to advance straight forward and ensuring the "D" CUT FACE of the Volume shaft is oriented as
shown.

Tighten the 2 screws to secure the VR BASE.

5

VR BASE

SCREW (2)
M4 X 12, w/flat & spring washers

"D" CUT FACE

FIG. 9. 1 a

6

Turn on power.

7

Set the Center Value of the Volume in the TEST mode.

In the TEST mode, check to see if the Volume Value varies smoothly in accordance with the

8

steering wheel operation.

64

REPLACING THE VOLUME

1

Disconnect the connector from the
Volume.

2

Take out 2 screws to remove the
Volume together with VR BASE
from the HANDLE MECHA.

SCREW (2)
M4 X 12, w/flat & spring washers

Take out 2 screws from the VR

3

BASE reverse side to remove the
Volume together with VR Bracket
from the VR BASE.

4

Remove the Volume from VR
Bracket and replace.

TRUSS SCREW (2)
M4 X 12

PHOTO 9. 1 b

VR BASE

65

PHOTO 9. 1 c

After replacing the Volume, engage the gears at the angular position shown and fix the VR

5

Bracket.

VR BASE

SCREW(2)
M4 X 12, w/flat & spring washers

FIG. 9. 1 b

V.R.
220-5484

220-5373

6

Turn on power.

7

Set the Center Value of the Volume in the TEST mode.

8

In the TEST mode, check to see if the Volume Value varies smoothly in accordance with the
steering wheel operation.

9 - 2 GREASING

STOP

IMPORTANT

Apply greasing to gear mesh
portions once every 3 months.
Use GREASE MATE (SEGA
PART NO. 090-0066).

Be sure to use the designated grease. Using undesignated grease can cause
parts damage.

Do not apply greasing to undesignated places. Failure to observe this can cause
malfunctioning or quality deterioration of parts.

VOLUME GEAR MESH PORTION

66

PHOTO 9. 2

10. ACCELERATOR & BRAKE

Before starting to work, ensure that the Power SW is OFF. Failure to observe
this can cause electric shock or short circuit.
Use care so as not to damage wirings. Damaged wiring can cause electric
shock or short circuit.
Do not touch undesignated places. Touching places not designated can cause
electric shock or short circuit.
This work should be performed by the Location's Maintenance Man or
Serviceman. Performing work by non-technical personnel can cause electric
shock hazard.
When performing work such as parts replacement other than those specified
in this manual, be sure to contact where you purchased the product from.
Confirm the work procedures and obtain precautions from where you
purchased the product from prior to performing work. Inappropriate parts
replacement and/or installation with erroneous adjustment can cause an
overload or the parts to come into contact, resulting in an electric shock, a
short circuit, and a fire.

If Accel. and Brake operation is not satisfactory, adjustment of Volume installation position or
Volume replacement is needed. Also, be sure to apply greasing to the gear mesh portion once
every 3 months.

10 - 1 ADJUSTING AND REPLACING THE V.R.

The appropriate value for both ACCEL. Volume and Brake Volume is under 30H when released
and over C0H when stepped on. Check Volume values in the TEST mode. Since work is
performed inside the energized cabinet, be very careful so as not to touch undesignated places.
Touching places not specified can cause electric shock or short circuit.

1

Take out the 2 truss screws and
remove the Front Cover from the
Accel. & Brake Unit

Loosen the screw which secure the

2

Potentiobase, and adjust the
Volume value by moving the Base.
(FIG. 10. 1 b)

3

Secure the Potentiobase.

4

Perform Volume setting in the
Volume setting mode.

SCREW
M5 X 12,

w/flat & spring washers

V.R.
220-5484

220-5373

POTENTIOBASE

FIG. 10. 1 b

67

REPLACING THE VOLUME

1

Turn the power off.

2

Take out the 2 screws and remove the
Pedal cover (FIG. 10. 1 c).

Disconnect the connector of the

3

Volume to be replaced.

Remove the screw which secures the

4

Pedal base (FIG. 10. 1 b).

5

Remove the Pedal base together with
the Volume as is attached.
(FIG. 10. 1 c)

Remove the Base and Gear to replace

6

the Volume.

Adjust the Volume as per the previous

7

page after replacing.

10 - 2 GREASING

FIG. 10. 1 c

PEDAL COVER

TRUSS SCREW (2)
M4 X 8

STOP

Be sure to use the designated grease. Using undesignated grease can cause parts
damage.

IMPORTANT

Once every 3 months, apply greasing
to the Spring and Gear mesh portion.
For spray greasing, use GREASE
MATE (PART No. 090-0066).

GREASING

FIG. 10. 2

68

11. COIN SELECTOR

HANDLING THE COIN JAM

If the coin is not rejected when the REJECT button is pressed, open the coin chute door and
open the selector gate. After removing the jammed coin, put a normal coin in and check to see
that the selector correctly functions.

CLEANING THE COIN SELECTOR

STOP

Remove and clean smears by using a
soft cloth dipped in water or diluted
chemical detergent and then

IMPORTANT

squeezed dry.
Never apply machine oil, etc. to the
Coin Selector.
After cleaning the Coin Selector,
insert a regular coin in the normal
working status and ensure that the
Selector correctly functions.

The coin selector should be cleaned once every
3 months. When cleaning, follow the procedure
below:
Turn the power for the machine OFF. Open the

1

coin chute door.
Open the gate and dust off by using a soft brush

2

(made of wool, etc.).
Remove and clean smears by using a soft cloth

3

dipped in water or diluted chemical detergent
and then squeezed dry.
Remove the CRADLE.

4

When removing the retaining ring
(E ring), be very careful so as not to bend the
rotary shaft.
Remove stain from the rotary shaft and shaft

5

receiving portions by wiping off with a soft
cloth, etc.
After wiping off as per above, further apply

6

a dry cloth, etc. to cause the coin selector to dry
completely.

COIN INSERTION TEST

Once every month, when performing the
Coin SW Test, simultaneously check the
following:

Does the Coin Meter count satisfactorily?
Does the coin drop into the Cashbox
correctly?
Is the coin rejected when inserted while
keeping the Reject Button pressed down?

GATE

FIG. 11a

CRADLE

FIG. 11 b

5

Insert a coin
while keeping the
Reject Button
pressed down and
check if it is
rejected.

COIN METER

FIG. 11 c

69

WELLS-GARDNER

ELECTRONICS CORPORATION

2701 N. KILDARE CHICAGO, IL 60639
1-800-336-6630

WWW.WGEC.COM

WGD15-2110-01

OVER/UNDER MINI DOOR

2 ENTRIES WITH BILL

VALIDATOR BOTTOM DOOR

& SPECIAL ENCLOSURE

70

#

12

20

18

17

16

15

25

28

6

5

27

7

5

19

21

22

8

4

13

23

3

14

1

2

29

9

10

4

8

26

F

J

B

K

L

D

11

24

E

C

A

5

G

H

M

W.G. PART #

812-4150-011

1

812-4050-011

2

890-1002-00

3

890-1003-00

4

890-1017-00

5

890-1019-00

6

890-1300-00

7

891-0514-00

8

025X3711-001

9

025X3712-001

10

891-0509-162

11

891-0547-00

12

891-0100-4016

13

891-1008-107

14

891-1113-03

15

891-1113-011

16

891-1117-00

17

891-1118-00

18

891-1121-00

19

891-1311-16

20

891-1312-16

21

891-1109-16

22

020X1877-005

23

891-2216-16

24

890-1007-00

24A

890-1206-02

24B

24C REJECT CUP SIDE PLATE891-1105-01

24D 891-1106-00

24E

891-1107-00

24F

891-1110-00

24G

891-1116-16

24H

891-1125-00
892-1002-07

24J

892-1002-08

24K

892-1002-09

24L

892-1002-11

24M

891-0604-16

25

891-0614-16

26

892-1002-01

27

892-1002-021

28

892-1002-10 BRACKET, HOLD DOWN

29

DESCRIPTION

S-7 US 25c COIN MECH LEFT

S-10 US $1 COIN MECH RIGHT

HINGE SCREW

CLAMP SCREW

SCREW TRILOBULAR

WASHER INTERNAL TOOTH 3/4"

KEYHOOK

CLAMP UK 5/8" CABINET

ENCLOSURE W/CHUTE

METAL CASHBOX

DOUBLE FRAME

LOCK SINGLE BIT

COVER PLATE

BASE PLATE ASSEMBLY

E/R BUTTON US 4x25c/$1 LEFT

E/R BUTTON US $1 COIN RIGHT

LAMPHOLDER

LAMP WEDGE BASE 6 VOLT

SPRING, E/R BUTTON

BUTTON BEZEL, NYLON

REJECT BEZEL, NYLON

REJECT FLAP

NUT KEPS #8-32 X 5/16 HEX

MICROSWITCH ASSEMBLY

SCREW,FLAT HEAD M/S

KEP NUT

REJECT CUP BASE PLATE

BRACKET, MICROSWITCH

ADJUSTER, COIN

MICROSWITCH, BLACK - MED.

COVER, PLASTIC

CLIP, SNAP-ON

ELASTIC SNAP NUT

SLEEVE, SNAP-ON

SCREW, PAN HEAD

MINI DOOR 2 ENTRIES

MINI DOOR W/DBV C/O

BRACKET, LAMPSIDE

BRACKET, COVERSIDE

Guardian Hasp

30-2400-200

Tom Happ Ph: 847-593-6161 ext. 107

[e-mail] Fx: 847-956-2091

Happ Controls, 106 Garlisch Drive, Elk Grove, IL 60007

Visit our website http://www.happcontrols.com

71

OPTIONAL DOLLAR BILL ACCEPTOR

THE COIN DOOR ASSEMBLY USED ON CLUB KART STD COMES
EQUIPPED TO ACCEPT A DOLLAR BILL ACCEPTOR. ALL NEEDED
WIRING CONNECTIONS ARE CONVIENENTLY LOCATED INSIDE THE
GAME FOR THIS APPLICATION.

THE COIN DOOR CAN ACCCOMMODATE THE FOLLOWING
VALIDATOR(S):

FORWARD-MOST Mars 2000 series
HOLE POSITION

**42-1155-00 MARS VALIDATOR $1, 2, 5 300 CAP

The frame and cashbox enclosure on this coindoor has been modified to accomodate
a Mars 2000 series upstacker. A 2000 series stacker can be added by simply remov­ing the cut-out plate. This one entry door can be ordered through Happ Controls or
one of Happ Controls authorized distributors. The part number is 40-6000-10EX.
The Mars stacker can be obtained through an autherized Mars distibutor.

Note: Your game may have either Happ Controls Coin Door Assembly or the Wells
Gardner Coin Door Assembly (not shown).

**Happ part number

Security Locking Bar/Bracket Set Part No.# 999-0966

Modified Cash Box (For use when DBA installed)
Part No. # 999-1106

Plastic Cash Box - Full Size Part No. # 999-1177

72

12.

REPLACING THE FLUORESCENT LAMP, AND LAMPS

When performing work, be sure to turn power off. Working with power on
can cause electric shock and short circuit hazards.
The Fluorescent Lamp, when it gets hot, can cause burn. Be very careful
when replacing the Fluorescent Lamp.
Be sure to use lamps of the designated rating. Using lamps of undesignated
rating can cause a fire or malfunctioning.

To perform work safely and securely, be sure to prepare a step which is in a
secure and stable condition. Performing work without using the step can
cause violent falling down accidents.
Be careful when handling the plastic made parts. Failure to observe this may
cause injury due to damage or fragments resulting from damage.

INSIDE THE BILLBOARD

Remove the billboard holder, slide up the billboard plate, and replace the fluorescent tube.

FIG. 12 a

FLUORESCENT LAMP 24W:390-5251-32-01
GLOW LAMP:390-5638-5P

73

START BUTTON,VIEW CHANGE BUTTON

1

Turn power off.

Remove the 4 Trusshead screws.

2

TRUSS SCREW (4)
M4 X 8, chrome

START BUTTON

VIEW BUTTON

PHOTO 12 a

Remove the switch plate from the

3

control panel carefully without
damaging the wires.

On the rear side of the switch plate there is a metallic projection

4

on the foot of each button. Turn the projection to unlock, and
remove the wire connection part from the button body.

The lamp is inside the wiring

5

connecting portion. Push and then
turn the Lamp counterclockwise to
remove.

74

13. PERIODIC INSPECTION TABLE

The items listed below require periodic check and maintenance to retain the performance of this
machine and to ensure safe business operation.
When handling the controller, the player will be in direct contact with it . In order to always
allow the player to enjoy the game, be sure to clean it regularly. Also, it is advisable to provide
wet tissue, etc. available for player use.

Be sure to check once a year to see if Power Cords are damaged, the plug is
securely inserted, dust is accumulated between the Socket Outlet and the
Power Plug, etc. Using the product with dust as is accumulated can cause fire
and electric shock hazards.
Periodically once a year, request the place of contact herein stated or the
Distributor, etc. where the product was purchased from, as regards the internal
cleaning. Using the product with dust as is accumulated in the interior
without cleaning can cause a fire or accident. Note that cleaning the interior
parts can be performed on a pay-basis.

TABLE 13

Item Interval Reference
CABINET Check Adjusters'contact with surface. Daily 3
CONTOROL PANEL Cleaning As necessary

Inspection of SW, VR. Monthly 8

Greasing to the gear mesh portion. Trimonthly 9-2
ACCEL. & BRAKE Check VOLUME VALUE. Monthly 8

Gear and Spring portion greasing Trimonthly 10-2
COIN CHUTE DOOR Check COIN SW. Monthly 8

Coin insertion test. Monthly 11

Cleaning of COIN SELECTOR. Trimonthly 11
PROJECTOR SCREEN cleaning. Weekly

Check adjustments.
SEAT Greasing to the seat rail Trimonthly FIG.13
GAME BD MEMORY TEST. Monthly 8

Check settings. Monthly 8
INTERIOR Cleaning Annually See above.
POWER SUPPLY PLUG
Cabinet surfaces Cleaning As necessary. See below.

Inspection and cleaning

Monthly or when moving.

5,8, 10

CLEANING THE CABINET SURFACES

When the cabinet surfaces are badly soiled, remove stains with a soft cloth dipped in water or
diluted (with water) chemical detergent and squeezed dry. To avoid damaging surface finish, do
not use such solvents as thinner, benzine, etc. other than ethyl alcohol, or abrasives, bleaching
agent and chemical dustcloth.

75

SEAT (Greasing to Seat Rail Portion)

Move the Seat to the rearmost portion and apply
spray greasing to the portion shown at the right
once every 3 months by using NOK KLUBER L60
or GREASE MATE SEGA PART No. 090-0066.
After greasing, move the Seat a few times forward
and backward so as to allow the grease to be
applied all over uniformly. Be sure to wipe grease
which attaches to the surfaces of the PROTECT
RUBBER on the Seat Rail, or any excess grease.

FIG. 13

76

14. TROUBLESHOOTING

In order to prevent electric shock and short circuit, be sure to turn power off
before performing work.
Be careful so as not to damage wirings. Damaged wiring can cause electric
shock or short circuit.
After removing the cause of the functioning of the Circuit Protector, reinstate
the Circuit Protector. Depending on the cause of the functioning, using the
Circuit Protector as is without removing the cause can cause generation of
heat and fire hazard.

In case a problem occurs, first check wiring connector connections.

TABLE 14 a

PROBLEMS CAUSE COUNTERMEASURES

With Main SW ON,
no activation.

The color on monitor
screen is incorrect.

Color deviation on
monitor screen.

No sound is emitted.

Power is not supplied.

Power supply/voltage is not correct.

The Circuit Protector functioned
due to the momentary overload.

Image adjustment is inappropriate.

Affected by peripheral machines or
the building's steel frames.

Sound volume adjustment is not
appropriate.

Securely insert the power plug into the
plug socket.

Make sure that power supply/voltage is
correct.

After eliminating the cause of overload,
reinstate the AC Unit's Circuit Protector
(see 4 , Sec. 5, Refer to the following).
Reset the circuit protector on the ASSY
ELEC. (see PHOTO 16 a, b)

Adjust appropriately.

Perform convergence adjustment

Change installation direction or position.

Move the machine which causes the
problem.

Adjust sound volume (see Sec. 8).

Board and Amplifier
malfunctioning.

Perform the sound test and confirm
(see Sec. 8).

77

TABLE 14 b

PROBLEMS CAUSE COUNTERMEASURES

Operability of the
Steering wheel
(handle) is poor.

Steering wheel
(handle) is
abnormal in its
force feedback. It
is not centered.

Steering wheel
(handle) is week
in its force
feedback.

Gas pedal
(accelletor) and/or
brake pedal do not
operate normally.

Deviation of the volume value.

Volume gear engagement fault.

Volume malfunctioning.

Failure of power-on checking
procedure.

The volume is not centered.

Failure of the volume.

Aging of the force feedback
mechanism.

The volume is not centered.

Failure of the volume.

Adjust the volume value in the Test mode.
(see 8-3)

Adjust the engagement of the gear.
(see 9-2)

Replace the Volume. (see 9-2)

Reconnect the power, and complete a
power-on checking procedure.
(see 5 Sec. 5,)

Adjust the volume value in the test mode.
(see Sec. 8)

Replace the volume. (see 9-1)

Reset in the test mode. (see Sec. 8)

Adjust the volume value in the test mode.
(see Sec. 8)

Replace the volume. (see 10-1)

The Fluorescent
lamp does not
light up.

Lights integrated
with the start
button and the
view change
button do not
come on.

Failure of the
communication
play.

'ERROR *' is
displayed.

The Fluorescent tube is burnt out.

The lamp is burnt out.

Communication cables are
disconnected.

Communication cables are wrongly
connected.

Communication play is wrongly set.

Setting error in the test mode.

Replace the Fluorescent tube
(see Sec. 12).

Replace the lamp. (see Sec.12)

Reconnect the cables. (see 18-2)

Reconnect the cables correctly. (See 18-2)

Reset correctly. (see 18-3)

Reset correctly in the test mode according
to the product. (see Sec. 8)

78

15. GAME BOARD

In order to prevent electric shock and short circuit hazards, be sure to turn
power off before performing work.
Be careful so as not to damage wirings. Damaged wiring can cause fire,
electric shock and short circuit hazards.
Do not expose the Game BD, etc. without a good reason. Failure to observe
this can cause electric shock hazard or malfunctioning.

The electronic parts on the IC Board could be damaged due to human body's static
electricity. Before performing IC Board related work, be sure to discharge
physically accumulated statics by touching grounded metallic surfaces, etc.

STOP

IMPORTANT

Put the Game Board in the Carton Box (an accessory) together with the Shield
Case when requesting for the replacement or repair. Transporting the Game
Board in an undesignated status for replacement/repair is unacceptable.
In this manual, how to remove the Game Board is explained for convenience.
However, this work should be performed by SEGA SERVICEMAN.

79

15 - 1 REMOVING THE GAME BOARD

Turn power off.

1

2

Remove the 2 trusshead screws of the back lid, unlock it, and detach it from the main cabinet.

Disconnect the connectors of all the wires between the ASSY MAIN BD STD and the main

3

cabinet.

Disconnect the connectors of all the wires between the shield case's filter board on the ASSY

4

MAIN BD STD and the main cabinet.

Remove the 2 wing bolts that fix the base (a wooden plate) of the ASSY MAIN BD STD.

5

Draw out the ASSY MAIN BD STD from the main cabinet. More than two workers

6

must engage in this action. Note that the ASSY MAIN BD STD is heavy, and, if a
single worker draws out it alone, he/she may damage the wires by snagging or catching
the wires on other parts.
NOTE: If you remove the 3 screws and detach the shield case lid, you can access to the
game board. This action is allowed, however, only for the Sega's service engineer.

7

Remove the 4 screws that fix the shield case onto the base (a wooden plate), and detach
the former from the latter.

8

Remove the 2 screws each, and detach the shield case from the shield case brackets.
Wrap the shield case with protective shipping materials, and contain it in a carton box.
Send it for repairing.

80

16. COMMUNICATION PLAY

For this game, up to 8 machines can be connected to allow up to 8 players to play
simultaneously. In this instance, connecting the communication cable and setting for the
communication play are required.

16 - 1 INSTALLATION PRECAUTIONS

Before starting to work, ensure that the Power SW is OFF. Failure to observe
this can cause electric shock or short circuit.
Use care so as not to damage wirings. Damaged wiring can cause electric
shock or short circuit.
Do not touch undesignated places. Touching places not designated can cause
electric shock or short circuit.
This work should be performed by the Location's Maintenance Man or
Serviceman. Performing work by non-technical personnel can cause electric
shock hazard.
When linking a number of machines, be sure to supply sufficient power for
the corresponding number of machines. Be sure to secure per machine
current as stated in this manual. Failure to observe this can cause a fire and an
electric shock accident.
Due to the length of the communication cable, the distance in between the
machines is limited. However, to avoid accidents, be sure to secure space in
excess of 70 cm between the machines.
To perform work safely and avoid serious accident such as the cabinet's
falling down, do not perform work in places where step-like grade
differences, a ditch, or slope exist.

To perform work safely, be sure to secure the space corresponding to number of
machines to be linked. Failure to observe this can cause accident.

STOP

IMPORTANTIMPORTANT

IMPORTANT

IMPORTANTIMPORTANT

The optic fiber cable is used for the communication linkage.
Excessive bending may damage the communication cable. Be very careful in this
regard.

Since 2 or more machines are to be linked, sufficient power corresponding to the number of
machines used need to be supplied. Note that as a standard, the per machine capacity should be
15A for the 100 ~ 120V area, and 7A for the 220 ~ 240V area.

81

DISTANCE BETWEEN MACHINES

Be sure to secure space in excess of 70cm between machines.

70cm

70cm

FIG. 16. 1

82

16 - 2 SETTING FOR COMMUNICATION PLAY

STOP

During communication play, if the test mode is not finished within 3 minutes on
all the linked machines, the NETWORK CHECK cannot be performed, causing
NETWORK ERROR.

IMPORTANTIMPORTANT

IMPORTANT

IMPORTANTIMPORTANT

Change the game setting for each seat in a manner so as to meet communication play. If the
setting is not correct, communication play cannot be played.

SETTING FOR COMMUNICATION PLAY

1

Turn the linked machines' power on.

2

Cause all of the machines to enter the test mode.

3

Select the SYSTEM ASSIGNMENTS.

4

Perform the COMMUNICATION MODE setting in the SYSTEM ASSIGNMENTS screen. Set
one of the machines to MASTER and all others to SLAVE. Set to RELAY for exclusive use of
LIVE Monitor.

SYSTEM ASSIGNMENTS

CABINET TYPE 1PLAYER
ADVERTISE SOUND ON
MONITOR TYPE HORIZONTAL
DISPLAY MODE AUTOSCAN
SERVICE TYPE COMMON
> COMMUNICATION MODE MASTER
EXIT

SELECT WITH SERVICE BUTTON
AND
PRESS TEST BUTTON

FIG. 16. 2 a

Activate the game test mode. (8-3)

5

Select and open the GAME ASSIGNMENTS screen. Note that the screen looks different

6

between the MASTER and SLAVE game machines.

7

Perform the SEAT NUMBER setting in the GAME ASSIGNMENTS screen. Set the machines
sequentially to No.1, No.2, No.3, and so on as applicable starting from the extreme left facing
the monitor's front side. Set every seat number correctly without duplication.

83

GAME SETTINGS

LINK TYPE: STAND ALONE
STEERING POWER: ************
STEERING DIR.: REVERSE
CARD SYSTEM: ENABLE
BONUS GAME: 0

EXIT

SELECT WITH SERVICE BUTTON
AND
PRESS TEST BUTTON

FIG. 16. 2 b

Cause all of the machines to exit from the test mode. After the test mode, the screens proceed to
and display the NETWORK CHECK.

When a network-checking is finished, the system displays am advertisement screen. This means
a successful completion of setting. If any seat number is duplicated, an error message appears
on the screen. Normally the NETWORK CHECK takes less than one minute. If the screen
does not proceed from the NETWORK CHECK screen, some sorts of errors such as incorrect
setting, or incorrect connection or malfunctioning of the communication cable can be
considered.

16 - 3 CAUTIONS TO BE HEEDED DURING COMMUNICATION PLAY

STOP

With a communication play, the ADVERTISE SOUND and GAME
DIFFICULTY items can be set only on the MASTER game machine. New
settings by the MASTER game machine become effective to all the

IMPORTANTIMPORTANT

IMPORTANT

IMPORTANTIMPORTANT

interconnected game machines.
If any setting is inadequate or if the communication cables are improperly
connected, the system keeps displaying the network-checking screen or an
error message. If this is the case, you cannot play the game.
During communication play, if communication is interrupted due to some
cause, the game is discontinued and the NETWORK CHECK screen is
displayed.
If one of the linked machines enters the test mode, all others display the
NETWORK CHECK screen.

Machine's operation when linked for communication play alters comparing to that of when
independently operated. Be careful of this point.
As described above, some setting items must be set only on the MASTER game machine. They
cannot be set on any SLAVE game machines or, if set, will not become effective.
When any game machine is in a test mode, a network-checking screen appears on the other
game machines interconnected for a communication play. While a guest is using any one of the
interconnected game machines, therefore, do not activate a test mode even on the unused game
machine.

84

17. DESIGN RELATED PARTS

For the Warning Display stickers, refer to Section 1.

2

1

4

5

6

9

8

7

85

ITEM NO. PART NO. DESCRIPTION

1 999-1263 MARQUEE
2 999-1265 DECAL SIDE LEFT - MONITOR

NOT SHOWN 999-1264 DECAL SIDE RIGHT - MONITOR

4 999-1250 DECAL NUMBER SHEET #2-8 SEAT

NOT SHOWN 999-1256 DECAL NUMBER SHEET #2-8 PEDESTAL

5 999-1251 DECAL REAR SEAT
6 999-1268 DECAL TOP REAR BASE
7 999-1269 DECAL BACK REAR BASE
8 999-1267 DECAL LEFT SEAT BASE

NOT SHOWN 999-1266 DECAL RIGHT SEAT BASE

9 999-1270 DECAL CONTROL PANEL

NOT SHOWN 999-1271 DECAL INSERT CLUB CARD

86

18. PARTS LIST

1 TOP ASSY (D-1/1)

1

9

8

10

3

7

6

5

4

2

11

87

1 TOP ASSY (D-2/2)

ITEM NO. PART NO. DESCRIPTION

1 LOC. PURCHASE FLUORESCENT FIXTURE 20 WATTS 24”

NOT SHOWN 999-1258 CARD READER ASSY

2 999-1257 REAR SEAT COVER (GREEN)
3 999-1262 S/A; TUBE - BUTTERCUP YELLOW
4 999-1287 FLOOR MAT
5 999-1285 COVER PEDAL FRONT

NOT SHOWN 999-1286 COVER PEDAL BACK

6 999-0167 LEG LEVELER 1/2-13 X 3” (6 PER)
7 999-0169 CASTER 160-2 1/2 #25188 SWIVEL (8 PER)
8 SPG5-2200-A ACCELERATOR PEDAL

NOT SHOWN SPG5-2200-B BRAKE PEDAL

9 SPG-2001 STEERING WHEEL

NOT SHOWN N/A COIN METER

10 130-5162 GULL BOX SPEAKER 8 OHM 8W (SEAT)
11 130-5156 SPEAKER BOX 8 OHM 20 WATT

88

2 AC UNIT

1

104

ITEM NO. PART NO. DESCRIPTION

1 999-1043 AC BRKT
NOT SHOWN DYN-0402 NOISE FILTER BASE
NOT SHOWN 421-8202 STICKER EARTH MARK

104 999-0676 SW ROCKER J8 V-B

89

3 FAN UNIT (STR-1070)

CONNECTOR

ITEM NO. PART NO. DESCRIPTION

1 105-5340-01 FAN BRKT LONG

101 LOC. PURCHASE FAN AC120V
102 601-8543 FAN GUARD

201 000-P00312-W M SCR PH W/FS M3 X 12

90

4 ASSY CONNECTOR PLATE (NCR-1080)

ITEM NO. PART NO. DESCRIPTION

1 NCR-1081 CONNECTOR PLATE
2 421-7515 STICKER FIBER CABLE TX/RX

101 211-5479-01 CONN OPT JOINT

201 000-P00312-W M SCR PH W/FS M3 X 12

91

5 SW UNIT

2

1

3

ITEM NO. PART NO. DESCRIPTION

1 LOC. PURCHASE COIN METER 6 VOLTS
2 LOC. PURCHASE PUSH BUTTON SW
3 LOC. PURCHASE 5 K POTENTIOMETER & VOLUME KNOB

92

6 ASSY CTRL PNL (NCR-2000)

1

4

2

3

ITEM NO. PART NO. DESCRIPTION

1 LOC. PURCHASE PUSHBUTTON SML ROUND YEL VLT COMP. 57-2000-35
NOT SHOWN NCR-2006 STEERING COLLAR

2 SPG-2001 STEERING WHEEL

3 SPG-2002 STEERING EMBLEM

4 LOC. PURCHASE PUSHBUTTON RECT. VLT BLUE 57-2000-62

93