Schneider Electric TSMN-57011-xxx-0-01, TSMN-58011-000-0-01, TSMN-81011-000-0-01 Installation Instructions

Application

The Electronic Room Temperature Sensor is a resistance-temperature device (RTD) available in various models. See Table-1 below for model variations and options.

Features

• Contemporary, low-profile packaging

• Easily installed base plate and electronic assembly

TSMN-90xxx Series TSMN-57011-xxx-0-01 TSMN-58011-000-0-01 TSMN-81011-000-0-01

Electronic Room Temperature Sensor

General Instructions

• High-impact cover

• Suitable for direct-wall, 2 x 4 electrical box, 1/4 DIN

electrical box, and surface box mounting

• UL 916 Listed

Table-1 Model Chart.

Base Plate Terminals

Model No. Function

TSMN-90110-000-0-01 10K thermistor no shunt, ASD jack X X X X X

TSMN-90220-850-0-01 10K thermistor w/11K shunt, ASD jack X X X X X

TSMN-90221-850-0-01

TSMN-90230-850-0-01 10K thermistor w/11K shunt, ASD jack, ovrd X X X X X

TSMN-90231-850-0-01

TSMN-90250-850-0-01

TSMN-90250-852-0-01

TSMN-90251-850-0-01

TSMN-90256-852-0-01

TSMN-90261-850-0-01

TSMN-57011-0-01 10K thermistor 6” Pigtail leads

TSMN-57011-850-0-01 10K thermistor with 11K shunt 6” Pigtail leads

TSMN-58011-000-0-01 1K Platinum element 6” Pigtail leads

TSMN-81011-000-0-01 1K BALCO element 6” Pigtail leads

10K thermistor w/11K shunt, ASD jack, F temp ind

10K thermistor w/11K shunt, ASD jack, F temp ind, ovrd

10K termistor w/11K shunt, ASD jack, F setpt, ovrd

10K thermistor w/11K shunt, ASD jack, C setpt, ovrd

10K thermistor w/11K shunt, ASD jack, F temp ind, F setpt, ovrd

10K thermistor w/11K shunt, ASD jack, C temp ind, C setpt, ovrd

10K thermistor w/11K shunt, ASD jack, F temp ind, F setpt

ASD+ ASD- SETPT SP+ COM SPACE PSI

12345678

XX X X X

XXXXXX X

SPECIFICATIONS

Sensing Element: See Table-1 and Table-2. Mounting: Direct-wall,2x4electrical box, 1/4 DIN, or surface box. Ambient Temperature Limits:

Shipping & Storage, -40 to 160 °F (-40 to 71 °C)

Operating, 40 to 140 °F (4 to 60 °C) Humidity: 5 to 95%, non-condensing. Locations: NEMA.

Table-2 Temperature Versus Resistance.

Nominal Resistance Value

Temperature

°F (°C)

40 (4) — 7596 1017 935.9

50 (10) 18790 6938 1039 956.9

68 (20) 12260 5798 1077.9 995.6

77 (25) 10000 5238 1097.3 1015.4

86 (30) 8194 4696 1116.7 1035.4

104 (40) 5592 3707 1155.4 1076.2

122 (50) 3893 2875 1194 1118.0

140 (60) 2760 2206 1232.4 1160.9

Sensor Type

TSMN-90110 Series TSMN-57011 Series



Thermistor, 10Kat77

(25°C)

TSMN-90xxx-85x Series

TSMN-57011-850

Thermistor, 10Kat77

°F

(25°C), *with 11K shunt



resistor

TSMN-58011

°F

Platinum, 1000  at 32



(0°C)

°F

Balco, 1000  at 70°F

TSMN-81011



(21.1°C)

*TSMN-90110 and TSMN-57011 do not have a shunt resistor.

INSTALLATION

The electronic room temperature sensor is packaged, in disassembled form, in one container. It consists of three major parts: a pre-wirable base plate; an electronic assembly containing the sensor and its associated circuitry; and a removable cover.

Inspection Inspect the package for damage. If damaged, notify the appropriate carrier immediately. If

undamaged, open the package and inspect the device for obvious damage. Return damaged products.

Requirements • Job wiring diagrams

• Tools (not provided):

– Digital volt-ohm meter (DVM) – Appropriate drill and drill bit for mounting screws – Appropriate screwdrivers for mounting screws and terminal connections

• Training: Installer must be a qualified, experienced technician

• Appropriate accessories

– Communication adapter

• For use of this product with TAC System 8000, refer to the Environmental Controls

Application Manual, F-21335

Precautions Warning

Electrical shock hazard! Disconnect power before installation to prevent electrical shock or equipment damage.

Mounting Locate the sensor where it will be exposed to an unrestricted circulation of air which

represents the average temperature of the controlled space. Do not locate the sensor near sources of heat or cold such as lamps, motors, sunlight, or concealed ducts or pipes. The sensor is designed for service in any normally encountered human environment.

The electronic room temperature sensor may be installed directly onto a wall, or onto a 2 X 4 electrical box, a 1/4 DIN electrical box, or a surface box. Refer to Figure 1.

+ 4 hidden pages