Schneider Electric SQR50101 Specification

Instruction Bulletin

Specification of SQR50101**Z Z-Wave Plus Remote Dimmer Switch

Voltage

120 Vac, 60 Hz

Operating temperature

32–104°F (0–40°C)

Wireless type

Z-Wave (Support S2 and SmartStart)

Wireless frequency

908.40 MHz / 908.42 MHz / 916 MHz

CAUTION

HAZARD OF UNINTENDED USE

This device is intended to be used for non-critical automation activities. It is not intended to support life, safety, or medical equipment.

Failure to follow these instructions can result in personal injury or equipment damage.

DANGER

GDE7796300

SQR50101**Z Z-WaveTM Plus Remote Dimmer Switch

** = color code: WH (white), LA (light almond), BK (black), GY (gray)

Features

• Wireless Z-Wave technology creates a mesh network for command and control interoperability with other Z-Wave compliant controllers and devices.

• Work with other Z-Wave switch or dimmer devices for 3-way (multi-location) control, provide manual and remote control.

• The 3-way control can be achieved through below 2 methods.

o Association group control or

o Central scene control

• Child lockout capability.

NOTE:

• This remote switch is only a wireless controller, it cannot be used by itself

for single-pole control.

Precautions

Suitable for at least 90°C.

Instruction Bulletin

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

• Apply appropriate personal protective equipment (PPE) and follow safe electrical work practices. See NFPA 70E, NOM-029-STPS or CSA Z462 or local equivalent.

• This equipment must only be installed and serviced by qualified electrical personnel.

• Turn off all power supplying this equipment before working on or inside equipment.

• Always use a properly rated voltage sensing device to confirm power is off.

• Use with copper wire only.

• Indoor use only.

• Replace all devices, doors, and covers before turning on power to this

equipment.

Failure to follow these instructions will result in death or serious injury.

WARNING

HAZARD OF HEAT AND FIRE DAMAGE

Read all instructions before installation. The manufacturer will not be held responsible for product damage resulting from not following the instructions.

• Wet hands are strictly prohibited.

• Do not continue working after self-disassembly of any nature and damage of

external forces.

Failure to follow these instructions can result in death, injury or equipment damage.

GDE7796300

WARNING: This product can expose you to chemicals including Carbon black, which is known to the State of California to cause cancer, and Bisphenol A (BPA), which is known to the State of California to cause birth defects or other reproductive harm. For more information go to

www.P65Warnings.ca.gov.

Wireless Range Conditions

The wireless range is the effective distance of remote control and it will be impacted by the following conditions:

• Each wall or obstacle (e.g., refrigerator, TV, etc.) between the remote or Z-

Wave device and the destination device will reduce the wireless range.

• Brick, tile, or concrete walls block more of the wireless signal than walls made

of wooden studs and plasterboard (drywall).

• The angle of direction between the remote or Z-Wave device and the destination device will also impact the wireless range; normally, placing the ZWave devices face-to-face will get the best wireless range.

• Wall-mounted Z-Wave devices installed in metal junction boxes may suffer a significant loss of range since the metal box blocks a large part of the wireless signal.

Instruction Bulletin SQR50101**Z Z-Wave Plus Auxiliary Switch

Installation

1. Turn the power OFF at circuit breaker or fuse and test that power is off before wiring.

2. Wire the device according to the wiring diagram (Figure 1).

3. Check that all connections are tight and no bare wires exposed.

4. Install the device into the standard outlet box using the screws provided.

5. Install the plate (not included) (Figure 2).

6. Restore power.

Figure 2: Wall Plate

+ 6 hidden pages