Schneider Electric Smart-UPS VT Installation Instructions
Shipping Weights and Dimensions
10-20 kVA UPS 10-40 kVA UPS
XR battery
enclosure
200/208 V kg 200 V kg
Receiving and Unpacking
Smart-UPS® VT and
XR Battery Enclosure 10–40 kVA
380/400/415 V
208/220 V
200/208 V
UPS net dimensions
Enclosure Net Dimensions mm (in)
Height (identical for all UPS enclosure sizes) 1499 (59)
Depth (identical for all UPS enclosure sizes exclusive of the conduit box)
Depth (identical for all UPS enclosure
sizes - inclusive of the conduit box)
Enclosure width (2 sizes) 356 (14) and
828 (32.99)
925 (36.40)
559 (22)
UPS shipping weights
208/220 V kg lbs 208/220 V kg lbs
SUVTP10KF1B2 335.91 739 SUVTP10KF2B2 427.43 941
SUVTP10KF1B4 354.09 779 SUVTP10KF2B4 445.91 981
SUVTP10KF3B4 537.73 1183 SUVTP10KF4B4 630 1386
SUVTP15KF2B2 428.18 942 SUVTP15KF2B4 445.91 981
SUVTP15KF3B4 537.73 1183 SUVTP15KF4B4 630 1386
SUVTJP10KF1B2 335.91 SUVTJP10KF2B2 427.73
SUVTJP10KF1B4 354.09 SUVTJP10KF2B4 445.91
SUVTJP10KF3B4 537.73 SUVTJP10KF4B4 630
SUVTJP15KF2B2 428.18 SUVTJP15KF2B4 445.91
SUVTJP15KF3B4 537.73 SUVTJP15KF4B4 630
SUVTJP20KF2B4 475.91 SUVTJP20KF3B4 567.73
SUVTJP20KF4B4 660
SUVTJP30KF3B4 568.18 SUVTJP)0KF4B4 660
XR battery enclosure weights
Part Nos. kg lbs Part Nos. kg lbs
SUVTXR2B6 430.45 947 SUVTXR6B6S* 822 1807.6
SUVTBXR2B6 430.45 947 SUVTBXR6B6S* 825.4 1810.9
SUVTJBXR2B6 430.45 SUVTJBXR6B6S 828
* The total weight of the XR battery enclosure including the separate
battery packag
e.
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
Warning: Indicates a hazard, which, if not avoided could
result in personal injury or damage to product or other
property.
SUVTP20KF2B4 475.91 1047 SUVTP20KF3B4 567.73 1247
SUVTP20KF4B4 660 1452
SUVTP30KF3B4 568.18 1250 SUVTP30KF4B4 660 1452
380/400/415 V kg lbs 380/400/415 V kg lbs
SUVTP10KH1B2 335.91 739 SUVTP10KH2B2 427.73 941
SUVTP10KH1B4 354.09 779 SUVTP10KH2B4 445.91 981
SUVTP10KH3B4 537.73 1183 SUVTP10KH4B4 630 1386
SUVTP15KH2B2 428.18 942 SUVTP15KH2B4 445.91 981
SUVTP15KH3B4 537.73 1183 SUVTP15KH4B4 630 1386
SUVTP20KH2B2 428.18 942 SUVTP20KH2B4 445.91 981
SUVTP20KH3B4 537.73 1183 SUVTP20KH4B4 630 1386
SUVTP30KH3B4 568.18 1250 SUVTP30KH4B4 660 1452
SUVTP40KH4B4 660 1452
Receive
External inspection. When the shipment arrives, inspect the shipping
material for any signs of damage or mishandling. Do not attempt to
install the system if damage is apparent. If any damage is noted, contact
APC and file a damage claim with the shipping agency within 24
hours.
Compare the components of the shipment with the bill of lading.
Report any missing items to the carrier and to APC immediately.
Verify that labelled units match the order confirmation.
Move to Installation Site
Use a pallet jack or a forklift for components over 54 kg
(120 lb).
Note: After the unit has been removed from the pallet,
move it only by rolling it on the casters.
990-1747F-001
*990-1747F-
10/2008
Unpacking
Front-to-rear
airflow
Floor-to-ceiling
ventilation:
523 mm
(20 in)
Minimum
front clearance:
Minimum
rear
clearance*:
828 mm
(32.99 in)
100 mm
(4 in)
356 mm
(14 in)
1000 mm
(39.3 in)
Enclosure
356 mm
(14 in)
Front-to-rear
airflow
Floor-to-ceiling
ventilation:
523 mm
(20 in)
Minimum
front clearance:
Minimum
rear
clearance*:
828 mm
(32.99 in)
100 mm
(4 in)
559 mm
(22 in)
1000 mm
(39.3 in)
Enclosure
559 mm
(22 in)
Ramp
Land packaging.
Caution: Ensure that the floor is level. The enclosure
cannot be installed on a floor that is not level.
Space considerations
Note: Allow for enough working space behind the
enclosure for electrical work to be carried out (e.g. if you
want to connect an XR Battery Enclosure at a later stage).
10-20 kVA.
Unpack the enclosures
Caution: Do not unpack the units before the time of the
installation.
Note: If the system is not being installed immediately, do
not remove the packaging. Store the system in an indoor,
temperature-controlled area, free of conductive contaminats.
Heavy: There must be two people to roll the enclosure from
the pallet.
Note: Save four bolts for attaching the stabilizing brackets
to the 352 mm (13.85 in) enclosure. See “Stabilizing
Brackets” .
Cut carefully along the
edges to remove the plastic
and to free the ramp.
Place the ramp by aligning
the velcro strips on the ramp
with the velcro strips on the
front edge of the pallet.
Remove the cardboard
cover.
10-40 kVA.
* All physical installations must comply with local standards.
Remove the bolts from the
Remove the corner
protection and the plastic bag.
brackets attaching the
enclosure to the pallet and
save the brackets for floor
anchoring, if required.
Roll the unit off the pallet.
2
Loading...