Schneider Electric 560110R, 560125R-2, 560125D-2 User Manual

CLIPSAL

POWER MUTE < SOURCE > < VOLUME >

CLIPSAL

Multi Room Audio Amplifier

560125D/2 560125R/2 560110R

Installation Instructions

Multi Room Audio Amplifier Installation Instructions

Contents

1 Introduction 3

1.1 Product Range 3

1.2 Safety and Product Handling 4

1.3 Additional Product Information 6

2 Installation 7

2.1 Installation Steps 7

2.2 Equipment Placement 8

2.3 Wiring Diagrams 9

3 Wiring Details 11

3.1 Speaker Connections 11

3.2 C-Bus Network Cabling 12

3.3 Stereo Input Connection 13

3.4 Digital Audio Cabling for Multiple Amplifiers 13

4 Power Supply Connection 14

5 Commissioning and Testing 15

6 Troubleshooting 15

7 Specifications 16

8 Standards Complied 18

9 Two-Year Warranty 19

The information in this manual is provided in good faith. Schneider Electric endeavours to ensure the relevance and accuracy of the information. However, it assumes no responsibility for any loss incurred as a result of its use. Schneider Electric does not warrant that the information is fit for any particular purpose, nor does it endorse its use in applications that are critical to the health or life of any human being. Schneider Electric reserves the right to update the information at any time without notice.

November 2009

Multi Room Audio Amplifier Installation Instructions

1 Introduction

The installation instructions cover a 'standalone' Multi Room Audio (MRA) amplifier installation without a matrix switcher. A standalone amplifier configuration includes connections to a power supply, loudspeakers and a local stereo audio source. You can also connect additional MRA amplifiers using digital audio cables.

If you are installing a Multi Room Audio system that includes a matrix switcher, refer to the information found in the

Installation Instructions

C-Bus Multi Room Audio Matrix Switcher and System

After you install the amplifier, as described in this document, refer to the

Room Audio Amplifier User's Guide

for operating instructions.

C-Bus Multi

1.1 Product Range

Three types of MRA amplifiers are available as shown in Table 1.

Catalogue Number Description

560125D/2 MRA Desktop Amplifier

560125R/2 MRA Remote Amplifier

560110R MRA Low Power Remote Amplifier

560110E Enclosure only

Table 1. Amplifier catalogue numbers

Amplifiers

The 560125D/2 Desktop Amplifier is a high-power unit that has front panel controls and remote sensor window, in addition to the C-Bus network interface. The desktop amplifier is usually placed on a bedside table or on a shelf for easy access.

The 560125R/2 Remote Amplifier is a high-power unit that does not have front panel controls. The high power remote amplifier is normally placed in an equipment rack, built-in-robe, or above the ceiling. C-Bus input devices, such as wall switches, DLT switches, or a touchscreen provide volume and tone control.

The 560110R Low Power Remote Amplifier has a compact form factor that allows up to 4 units to be installed in a row in a standard 19-inch equipment rack. Unused locations can be filled using the 56011E empty enclosure. C-Bus input unit provide volume and tone control.

Refer to the 'Controls and Indicators' in the

User's Guide

for more details.

C-Bus Multi Room Audio Amplifier

Multi Room Audio Amplifier Installation Instructions

Power Supplies

Each Multi Room Audio Amplifier in a standalone installation requires a power supply (See Table 2) connected to the amplifier's EXTERNAL POWER socket.

Catalogue Number Description

5600P24/3750AU Switch Mode Power Supply, 24 V d.c. @ 3.75 A. Suits the

560125D/2 Desktop and the 560125R/2 Remote Amplifiers.

5600P24H3750A High Temperature Switch Mode Power Supply, 24 V d.c. @

3.75 A. Required for all high temperature locations. See note.

5600P24/1250 Power Supply, 24 V d.c. @ 1.25 A. Suits the 560110E Low

Power Amplifier.

Table 2. Power supplies for the amplifiers

Note: When the power supply is installed in warm to hot locations, you must use the High

Temperature Switch Mode supply for all amplifier types. The 3.75A High Temperature Power Supply includes a cable adapter for the 560110R Low Power Amplifier.

1.2 Safety and Product Handling

Read and understand the following safety hazard information.

WARNINGS

Failure to observe these warnings could lead to electrical shock and serious injury:

• Use only the specified power supply unit that is of the correct type for the amplifier you are using. Do not substitute any other power supply.

• Replace the power supply unit if the power supply or the cord is damaged. The power supplies cannot be repaired and there are no user serviceable parts inside.

• Do not allow liquids to splash or drip on the power unit or the amplifier. Do not place an object containing liquid, such as a vase, on top of the equipment.

To prevent overheating and the possibility of a fire, always provide adequate ventilation around the power supply. Do not cover the power supply or enclose it in a box.

Prevent tripping and falling by installing equipment in safe locations where cables do not create a tripping and falling hazard.

The amplifiers can produce sounds loud enough to cause permanent hearing loss. Prevent hearing loss by doing the following:

• Mute the speakers before connecting an audio source.

Multi Room Audio Amplifier Installation Instructions

• Turn down the volume setting before connecting headphones. Connect the headphones to the amplifier BEFORE placing them on your head.

• Do not allow children to use the Multi Room Audio equipment without adequate supervision.

Cautions

Prevent damage to the equipment and extend its useful life by following these guidelines:

• Only use a Clipsal approved power supply to power an amplifier. Using any other power supply can damage the unit, and void the warranty.

• The amplifiers are designed for indoor use only in moderate to tropical climates. Operating the equipment at high temperatures for extended periods will reduce reliability and product life.

• Provide adequate ventilation. Ensure at least 50 mm of free space is available at each side of the high power amplifiers. Allow at least 15 mm of free space directly above the units.

• Never insert C-Bus RJ45 plugs into LAN or Digital Audio sockets. Damage to the equipment can occur. The use of colour-coded network cables is highly recommended.

• Disconnect power from the amplifier before connecting or disconnecting cables.

Care Instructions

Maintain the appearance of the equipment by following these guidelines:

• Use a soft lint free cloth for cleaning.

• Do not use chemicals or spray cleaners.

• Do not use hard, sharp objects to select the controls.

• Do not allow dust to accumulate on the equipment.

Multi Room Audio Amplifier Installation Instructions

1.3 Additional Product Information

If you have technical questions about the installation of the Multi Room Audio equipment, contact your nearest Clipsal Integrated Systems or Schneider Electric customer care centre. The contact information is on the back cover of this document.