Sato MB400I B1, MB400I W2 User Manual

Download

Page 1

Barcode Printer

2345678901234567890123456789012123456

Quick Guide

2345678901234567890123456789012123456

Page 2

Preface

Thank you for purchasing the Barcode Printer, MB400i/410i. This manual is created so that a first-time user of MB400i/410i can learn its basic operations in a short time. Please read this manual carefully to make full use of the functions of MB400i/410i.

Cautions

1 Reproduction of all or part of this manual is prohibited. 2 The content of this manual is subject to change without notice. 3 This manual was created with utmost care regarding its content. However, if

you find any unclear points, errors, or omissions, please contact the retail store or dealer where you purchased this printer.

To customers purchasing the Bluetooth or wireless LAN options:

Cautions regarding radio waves

This product is certified to meet technical standards based on the Radio Law. Therefore, no wireless license is required to use this printer. The following actions can be punishable by law:

• Disassembly or modification of this printer

• Removing the certification label (serial label) on this printer

Use in the following locations may drastically shorten the communication distance, or prevent communication.

• Near a microwave oven; locations where static electricity or radio wave interference is

abundant; near wireless LAN equipment.

“Bluetooth” is a registered trademark of Bluetooth SIG, Inc. USA. Our company is using this trademark based on a licensing contract with this association.

Before using the wireless LAN interface, be sure to set all security-related settings for the wireless LAN equipment according to this manual.

Preparation

Operation

Troubleshooting

Care

Reference

Table of Contents

1. Safety Precautions........................................................................... 4

Markings and Symbols .......................................................................................... 4

Precautions in Use................................................................................................. 8

2. Unpacking ..................................................................................... 15

3. Names of Parts .............................................................................. 16

Names and Functions of Operating Parts ............................................................ 18

4. Preparing for First-time Operation ................................................. 19

Charging the Battery Pack ................................................................................... 19

Installing and Removing the Battery Pack ........................................................... 21

Using AC Adapter ............................................................................................... 22

Loading Labels ................................................................................................... 23

• Continuous printing mode ............................................................................ 23

• Dispense mode printing ............................................................................... 25

• Switching from Dispense mode printing to Continuous printing mode .......... 27

5. Turning the Power On .................................................................... 28

6. Test Printing ................................................................................... 29

7. Operation with an RS-232C Cable ................................................ 30

8. Operation with a USB Cable .......................................................... 31

9. Operation via Infrared Communication ......................................... 33

10. Operation with Bluetooth or Wireless LAN Options ...................... 33

11. Printing........................................................................................... 34

12. Troubleshooting ............................................................................. 36

13. Daily Care ...................................................................................... 39

14. Reference ...................................................................................... 41

Included Items ..................................................................................................... 41

Options ................................................................................................................ 41

Operation Modes ................................................................................................. 46

DIP Switch .......................................................................................................... 54

Basic Specifications of MB400i/MB410i .............................................................. 56

Page 3

1. Safety Precautions

Warning

In this section, safety precautions about printer operation are explained to ensure proper care and usage. Make sure to read these carefully before using your printer.

Markings and Symbols

The following symbols or markings are used in this manual and on the printer so that you can properly use the printer, and to prevent any damage to property, harm or injury to yourself and others. Make sure to read their explanations carefully to familiarize yourself with their meanings.

Safety Precautions

Warning

Caution

Symbol examples

The triangle indicates something you should take absolute care with. The cautions are indicated concretely within the symbol. The symbol on the left indicates a risk of electric shock.

A circle with a diagonal line indicates something you should not do. The symbol on the left indicates that you should not try to take the unit apart.

A black circle with a picture inside indicates something you need to do. The symbol on the left indicates that you should unplug the unit from the wall outlet.

This symbol indicates information that, if ignored or applied incorrectly, creates the danger of death or serious personal injury.

This symbol indicates information that, if ignored or applied incorrectly, creates the possibility of personal injury or property damage.

Liquid

Do not place any container with water or chemicals, such as flower vase or cup, as well as small metallic objects, near the printer. If any of these should drop into the printer, immediately turn off the power and contact your nearest dealer or service center. Continued use creates a danger of fire or electric shock.

Foreign Matter

Do not drop or insert metallic or flammable objects into the openings on the printer (such as outlets for cables). If any of these should fall into the printer, immediately turn off the power and contact your nearest dealer or service center. Continued use creates a danger of fire or electric shock.

Dropping and Damage

Should the printer ever be dropped or otherwise become damaged, immediately turn off the power and contact your nearest dealer or service center. Continued use creates a danger of fire or electric shock.

Abnormal Conditions

Continued use of the printer while it is emitting smoke or strange odors creates the danger of fire or electric shock. Immediately turn off the power and contact your nearest dealer or service center. Do not try to service the printer by yourself.

Disassembly

Never try to take the unit apart or modify it in any way. Doing so creates the danger of fire or electric shock. Contact your nearest dealer or service center for checking, adjustment, or repair.

Safety Precautions

Battery Pack

• Never try to take apart the battery pack or modify it in any way such as with a solder iron.

• Never expose the battery to direct flame, throw it into fire, or take any actions that may lead to shorting.

• When charging the battery pack, make sure to use the printer or the specified battery charger.

Page 4

Warning

Caution

AC Adapter/Battery Charger (Option)

• Use only the specified voltage. Using a different voltage may create the danger of fire or electric shock.

• Use only the specified AC adapter. Using a different one may create the danger of fire or electric shock.

• Never use the battery charger with any other battery pack except for the specified one. Doing so can rupture the battery, cause leakage, fire or electric shock.

• Never cut, damage or modify the power cord. Also, never place heavy objects on the power cord or heat or pull the power cord. Doing so may damage the cord and

Safety Precautions

create the danger or fire or electric shock.

• Should the power cord ever become seriously damaged (internal wiring exposed or shorted), contact your nearest dealer or service center for repair. Continued use of such a cord creates the danger of fire or electric shock.

• Never modify, excessively bend, twist, or pull the power cord. Doing so creates the danger of fire or electric shock.

Location

Do not locate the printer in the area subjected to high humidity or dew. If dew forms inside the printer, immediately turn off the printer and do not use it until it has been dried up. Continued use creates the danger of electric shock or the printer damage.

Power

• Do not use wet hands to operate the power switch, replace the battery pack or unplug the AC adapter or battery charger. Doing so creates the danger of electric shock.

• The AC adapter set provided for this printer is specific to this printer. Do not use it for other electric equipment.

Thermal Head and Stepping Motor

• The thermal head gets very hot after printing. Take care when replacing the label or cleaning the printer just after printing to avoid burns.

• Touching the end of the thermal head with bare hands may cause injury. Take care when replacing the label or cleaning the printer to avoid injury.

• Do not try to replace the thermal head by yourself. Doing so creates the danger of injury, burns, or electric shock.

Easy Cutter

This part contains a blade. Take care to avoid being injured by the blade and other sharp parts in the printer.

Replacing the Battery Pack

• Use only the specified battery pack.

• When replacing the battery pack, make sure to install the pack in the correct orientation. Incorrectly replacing the battery creates the danger of injury or damage to surrounding areas, explosion is caused.

• Replacing a small-size rechargeable battery (Lithium ion battery) Apply insulation treatment for the old battery pack by sealing the contact with tape or the like and ask our sales representative or service center for the measures to be taken to recycle the reusable materials. Do not place the battery pack together with other batteries such as dry batteries.

Safety Precautions

Leaving the printer unused for a long time

If you have no plan to use the printer for a long time, remove the battery pack from the printer and unplug the AC adapter from the wall outlet.

Maintenance and Cleaning

For safe maintenance or cleaning of the printer, make sure to remove the battery pack and the AC adapter from the printer.

Page 5

FCC REQUIREMENT



This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

FCC WARNING:

Changes or modifications not expressly approved by the manufacturer for compliance could void the user's authority to operate the equipment.

FCC NOTICE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

This manual show that both the specification of Bluetooth and wireless LAN. Please refer to the corresponding section which shows specification of Bluetooth or wireless LAN.

Wireless LAN specification:

The available scientific evidence does not show that any health problems are associated with using low power wireless devices. There is no proof, however, that these low power wireless devices are absolutely safe. Low power Wireless devices emit low levels of radio frequency energy (RF) in the microwave range while being used. Whereas high levels of RF can produce health effects (by heating tissue), exposure to low-level RF that does not produce heating effects causes no known adverse health effects. Many studies of low-level RF exposures have not found any biological effects. Some studies have suggested that some biological effects might occur, but such findings have not been confirmed by additional research. The MB400i-W2/MB410i-W2 has been tested and found to comply with FCC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guideline in Supplement C to OET65. Please refer to the SAR test report that was uploaded at FCC website.

Bluetooth specification:

This equipment complies with FCC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guideline in Supplement C to OET65. This equipment has very low levels of RF energy that is deemed to comply without testing of specific absorption radio (SAR).

8 9

Page 6

Properly shielded a grounded cables and connectors must be used for connection to host computer and / or peripherals in order to meet FCC emission limits. AC adaptor with ferrite core must be used for RF interference suppression.

CE Caution:

English

Español

[Spanish]

Ελληνική

[Greek]

Hereby, [name of manufacturer], declares that this [type of equipment] is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

Por medio de la presente [nombre del fabricante] declara que el [clase de equipo] cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.

ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ [name of manufacturer] ∆ΗΛΩΝΕΙ ΟΤΙ [type of equipment] ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ

ΟΥΣΙΩ∆ΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ∆ΙΑΤΑΞΕΙΣ ΤΗΣ Ο∆ΗΓΙΑΣ 1999/5/ΕΚ.

Česky [Czech]

Dansk [Danish]

Deutsch

[German]

Eesti [Estonian]

[Jméno výrobce] tímto prohlašuje, že tento [typ zařízení] je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.

Undertegnede [fabrikantens navn] erklærer herved, at følgende udstyr [udstyrets typebetegnelse] overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.

Hiermit erklärt [Name des Herstellers], dass sich das Gerät [Gerätetyp] in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.

Käesolevaga kinnitab [tootja nimi = name of manufacturer] seadme [seadme tüüp = type of equipment] vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.

[French]

[Latvian]

[Lithuanian]

[Dutch]

Français

Italiano [Italian]

Latviski

Lietuvių

Nederlands

Malti [Maltese]

Par la présente [nom du fabricant] déclare que l'appareil [type d'appareil] est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE.

Con la presente [nome del costruttore] dichiara che questo [tipo di apparecchio] è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.

Ar šo [name of manufacturer / izgatavotāja nosaukums] deklarē, ka [type of equipment / iekārtas tips] atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.

Šiuo [manufacturer name] deklaruoja, kad šis [equipment type] atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.

Hierbij verklaart [naam van de fabrikant] dat het toestel [type van toestel] in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.

Hawnhekk, [isem tal-manifattur], jiddikjara li dan [il-mudel tal-prodott] jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC.

10 11

Page 7

[Hungarian]

Magyar

Alulírott, [gyártó neve] nyilatkozom, hogy a [... típus] megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.

Polski [Polish]

Niniejszym [nazwa producenta] oświadcza, że [nazwa wyrobu] jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.

[Portuguese]

[Slovenian]

Português

Slovensko

[Nome do fabricante] declara que este [tipo de equipamento] está conforme com os requisitos essenciais

e outras disposições da Directiva 1999/5/CE.

[Ime proizvajalca] izjavlja, da je ta [tip opreme] v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES.

Slovensky

[Slovak]

Suomi [Finnish]

Svenska

[Swedish]

Íslenska [Icelandic] Hér með lýsir [name of manufacturer] yfir því að [type of

[Meno výrobcu] týmto vyhlasuje, že [typ zariadenia] spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES.

[Valmistaja = manufacturer] vakuuttaa täten että [type of equipment = laitteen tyyppimerkintä] tyyppinen laite on

direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.

Härmed intygar [företag] att denna [utrustningstyp] står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.

equipment] er í samræmi við grunnkröfur og aðrar kröfur, sem gerðar eru í tilskipun 1999/5/EC.

Norsk

[Norwegian]

If you want to get a copy of the original Declaration of Conformity of our products which relates the R&TTE, please contact to web address: www.satoworldwide.com

[Produsentens navn] erklærer herved at utstyret [utstyrets typebetegnelse] er i samsvar med de grunnleggende krav

og øvrige relevante krav i direktiv 1999/5/EF.

12 13

Page 8

Precautions in Use

2. Unpacking

Do not place the printer in a hot or cold place.

The operation temperature range is -15°C to 50°C (for wireless LAN: 0 to 50°C) where humidity does not cause condensation. Do not place the printer in an area with high humidity or at a temperature outside the specified range.

Do not drop or apply undue shock to the printer.

The printer is generally resistant to vibration possibly caused during normal transportation. However, do not apply extreme vibration or shock by dropping the printer.

Do not disassemble or modify the printer.

The printer has high-precision components inside requiring fine adjustment. Do not

disassemble the printer.

Safety Precautions

Connect the correct cables to the external input terminals.

Cables of the correct specifications are required for connection to the external equipment through the external input terminals. Contact your nearest dealer or service center if necessary.

Use the recommended accessories.

Using optional equipment other than the specified equipment may cause a malfunction. Always use the equipment specified in this guide.

Use the correct media.

Use the specified media. Otherwise, faulty printing or printer damage may occur.

Make sure you have all the printer components shown here. If any component is missing, contact the retail store or dealer where you purchased the product from.

Warranty

Quick Guide

Printer unit

Battery pack

Shoulder belt

Unpacking

* The appearance of any cushioning material supplied (such as protector pads on the

printer holder) may be changed across different production batches.

Page 9

3. Names of Parts

Label guide

Label width scale

Label guide stopper

Names of Parts

Cover release lever

Dispenser unit

Battery life indicator

(LED) *

STATUS (LED)

Main cover

Label dispenser

Infrared communication sensor

Easy cutter

RS-232C cover

Battery cover

USB/DIP switch cover

Label guide

110

100

908070

Platen

Names of Parts

RS-232C connector

USB connector

DIP switch

234 1

DC input terminal cover

PRINT button

POWER button

LCD *

FEED button

*1Only provided on wireless LAN interface operating panel (manufacturer option). For

other options, see “Options” on page 35.

*2On a wireless LAN interface operating panel (manufacturer option), a CHARGE LED is

provided.

Page 10

Names and Functions of Operating Parts

4. Preparing for First-time Operation

RS-232C cover:

This covers the RS-232C connector.

RS-232C connector:

Connects with a PC etc.

USB/DIP switch cover:

Covers the USB connector and DIP switch.

USB connector:

Connects with a PC etc.

Names of Parts

Main cover:

Open this cover to set the labels.

Cover release lever:

Use this to release the main cover.

Easy cutter:

Cuts the printed label.

Infrared communication sensor:

Contains an infrared receiver/transmitter element.

DIP switch:

Sets the operation mode. (See P. 48)

Dispenser unit:

Move this when using Dispense mode printing for the labels.

POWER button:

Turns the power on and off.

Battery cover:

A specialized battery pack is placed inside.

Battery life indicator (LED):

Displays the available battery power.

Label guide:

Set this to match the size of the label width used.

Label guide stopper:

Press this toward the back to unlock the label guide and adjust the label guide.

Label dispenser:

Printed labels are ejected here.

Label width scale:

Use this scale to match the label width used.

DC input terminal:

Connect the AC adapter.

DC input terminal cover:

Cover for the DC input terminal.

FEED button:

Feeds the labels.

PRINT button:

Takes the printer ONLINE and OFFLINE.

STATUS (LED):

Displays the printer status. (See P. 30-31 and 41-47)

Charging the Battery Pack

• Charging by installing the battery pack in the battery charger (optional)

Install the battery pack in the battery charger (optional) and charge it.

The optional battery charger set provided for this printer is specific to this printer. Do not use it for other electric equipment.

1 Connect the power cord to the

charger unit, then plug it into the outlet.

• When charging is complete, the CHARGE lamp lights green (fully charged).

2 Insert the battery pack. Insert the

battery pack into the slot, with the terminal pointing downward.

• When charging begins, the CHARGE lamp (red) lights. When charging is complete, the CHARGE lamp lights green (fully charged).

Preparing for First-time Operation

CHARGE

3 Remove the battery pack when

charging is complete.

Charging time

It takes about 1.5 hours for the CHARGE lamp to turn off when charging a completely depleted battery.

Page 11

Note

• When the CHARGE lamp is not lit, check that the battery pack is installed securely. The battery may not be charged when not securely installed.

• When a charged battery pack is installed, the CHARGE lamp first lights red, then lights green.

• Charging by installing the specialized AC adapter (optional) on the printer

This charges the battery pack while it is installed in the printer.

Installing and Removing the Battery Pack

1 Open the battery cover.

Preparing for First-time Operation

The AC adapter set provided for this printer is specific to this printer. Do not use it for other electric equipment.

1 Remove the DC input terminal

cover, and insert the DC output terminal.

2 Plug the AC adapter into the

outlet.

When charging begins, the battery life indicator lights red. When charging is complete, the battery life indicator disappears (fully charged).

*On a wireless LAN interface

operating panel (manufacturer option), the CHARGE LED lights red when charging begins. When charging is complete, the CHARGE LED turns off (fully charged).

Charging time

It takes about 5 hours for the battery remaining power display to turn off when charging a completely depleted battery.

AC adapter

DC output terminal

DC input terminal

2 While pressing the gray hook,

insert the battery pack, then close the battery cover.

Insert the battery pack with the terminal side toward the printer.

3 To remove the battery, press the

gray hook to unlock it, then hold the handle and pull out the battery.

* Be sure to turn the power off before removing or replacing the battery

pack. When the power is off, the STATUS LED turns off (see “Power OFF” on

page 22). Do not remove the battery pack until this light turns off. Make sure to check that the STATUS LED has turned off before

removing the battery pack.

* Note that removing the battery pack by the operation above may

prevent updating the information in the printer memory.

Handle

Hook

Terminal

Battery pack

Preparing for First-time Operation

Page 12

Using AC Adapter

Loading Labels

Install the specialized AC adapter (optional) on the printer for use.

The AC adapter set provided for this printer is specific to this printer. Do not use it for other electric equipment.

• Use AC ADAPTER: Model No. TG-5001-19v

1 Remove the DC input terminal

Preparing for First-time Operation

cover, and insert the DC output terminal into the input terminal.

AC adapter

2 Connect the AC adapter into the

outlet.

DC output terminal

* Be sure to turn the printer power off before detaching the DC output

terminal for the AC adapter, or disconnecting the power supply. Note that disconnecting the power supply in ways other than described

above may prevent the printer from correctly storing any settings in memory.

No battery pack is necessary when the AC adapter is used. When the battery pack and AC adapter are used simultaneously, charging begins if the battery is not fully charged. The display becomes normal when fully charged (See P. 14).

DC input terminal

The label installation method differs by printing mode.

Continuous printing mode

(See figure on P. 40)

Label paper

1 Slide the cover release lever in

the arrow direction to open the cover.

First, slide the dispenser unit to the continuous printing mode position. (See P. 21)

2 While pressing the label guide

stopper, slide the label guide to the label size to be used.

3 Load the paper in the printer.

Make sure the roll is oriented correctly.

Journal paper

Preparing for First-time Operation

Label guide stopper

Page 13

4 Confirm that the label roll can be

rotated easily by hand.

If rotation is labored, this can cause a feed error. Remove the label roll and adjust the label guide. Note that the label guides do not require adjustment when you are using labels with the same width.

Preparing for First-time Operation

5 Check that the label tip is

protruding. Then close the main cover by pressing the middle of the cover.

Close the main cover slowly, while pulling the cover release lever.

This completes loading the labels for continuous printing mode.

Dispense mode printing

(See figure on P. 40)

1 Slide the cover release lever in

the arrow direction to open the cover.

First, slide the dispenser unit to the continuous printing mode position. (See P. 21)

*Never slide the dispenser unit while

the main cover is open.

2 While pressing the label guide

stopper, slide the label guide to the label size to be used.

Label paper

Non-separated labels

Preparing for First-time Operation

Label guide stopper

3 Peel the label at the tip of the

label paper.

Dispense mode printing is not required for non-separated labels.

Page 14

4 Load the paper in the printer.

Make sure the roll is oriented correctly.

8 Slide the dispenser unit until it

stops.

This completes loading of the labels for dispense mode printing.

5 Confirm that the label roll can be

Preparing for First-time Operation

rotated easily by hand.

If rotation is labored, this can cause a feed error. Remove the label roll and adjust the label guide. Note that the label guides do not require adjustment when using labels with the same width.

6 Check that the label tip is

protruding (10 mm or more). Then close the main cover by pressing the middle of the cover.

Close the main cover slowly, while pulling the cover release lever.

7 For non-separated labels, press

the FEED button to feed one sheet, and pull upward to tear along the perforated line.

If the labels clog at the label dispenser, restart the label loading process from the beginning.

10mm

• Switching from Dispense mode printing to Continuous printing mode

Holding the dispenser/continuous switching lever upward, slide the dispenser unit toward you. Never pull it with the lever still engaged. This may damage the dispenser unit.

When using dispense mode printing, be sure to follow the procedure above to switch the dispenser unit from dispense mode printing to continuous printing mode, before changing the paper.

Preparing for First-time Operation

Page 15

5. Turning the Power On

6. Test Printing

When the preparation steps are complete, turn the power on or off.

Power ON

1 Hold down the POWER button

until the STATUS LED lights green. Then release the POWER

Turning the Power on

button.

POWER

Power OFF

2 Hold down the POWER button

again, until the STATUS LED turns off. Then release the POWER button.

POWER

1 When pressing the FEED button

and holding down the POWR button simultaneously, the printer enters the test mode. Press the FEED button again to start test printing.

FEED

POWER

FEED

Test Printing

2 Verify the following using the

output of the test print.

There are no chipped characters.

•

• Printing condition is good.

In test printing, the estimated remaining battery power is

  

”. (

  

displayed as “

FEED

completely charged.) When the remaining battery power is

when

  

charge the battery.

* If a problem occurs, contact the retail store or dealer where you purchased the printer

from, or our sales personnel or service center.

ABCDEFG

abcdefg

1234567

ABCDEFG abcdefg

1234567

Page 16

7. Operation with an RS-232C Cable

8. Operation with a USB Cable

To print with an optional RS-232C cable connected to a PC or a handheld terminal, perform the following operations.

1 Remove the USB/DIP switch

cover, and set the DIP switch (DSW) to DSW-1, 2, 3, 4 = (OFF, OFF, OFF, OFF).

Operation with an RS-232C Cable

2 Remove the RS-232C connector

cover.

RS-232C cover

3 Insert the RS-232C cable into

the connector.

Match the arrow on the RS-232C cable connector with the arrow beside the printer connector, and insert it firmly.

4 Connect the other end of the

RS-232C cable to the connector on the PC or the handheld terminal.

For the connector on the PC or the handheld terminal, see the manuals provided with that equipment.

RS-232C cable

To print with an optional USB cable (mini B type) connected to a PC or a handheld terminal, perform the following operations.

1 Remove the USB/DIP switch

cover, and set the DIP switch (DSW) to DSW-1, 2, 3, 4 = (ON, ON, OFF, OFF).

Operation with a USB Cable

2341

2 Insert the USB cable into the

connector.

Match the arrow on the USB cable connector with the arrow beside the printer connector, and insert it firmly.

3 Connect the other end of the

USB cable to the connector on the PC or the handheld terminal.

For the connector on the PC or the handheld terminal, see the manuals provided with that equipment.

USB cover

USB cable

Page 17

9. Operation via Infrared Communication

10.

Operation with Bluetooth or Wireless LAN Options

To print using infrared communication, perform the following operations.

1 Remove the USB/DIP switch

cover, and set the DIP switch (DSW) to DSW-1, 2, 3, 4 = (ON, OFF, OFF, OFF).

2 Place the printer within 20 cm of

Operation via Infrared Communication

the PC or handheld terminal for infrared communication.

3 Adjust the printer position so that the PC or handheld terminal is within a

30° area vertically and horizontally (cone shape) from the center of the infrared communication sensor.

30°

To print using a Bluetooth interface or a wireless LAN interface, perform the following operations.

1 Remove the USB/DIP switch

cover, and set the DIP switch (DSW) to DSW-1, 2, 3, 4 = (OFF, ON, OFF, OFF).

Operation with Bluetooth or Wireless LAN Options

2341

* Note that the effective distance varies with the usage environment,

computer, or handheld terminal in use.

2341

The maximum usage distance for infrared communication is 15 to 20 cm. *

However, this differs with the usage environment and the communicating equipment. Communication may not be possible in direct sunlight or under powerful illumination. In such cases, either shield the infrared communication sensor from harsh light, or place the infrared communication sensor in contact with the communicating equipment.

Page 18

. Printing

1 Data is sent from a PC.

2 When printing is complete, hold

the right or left corner of the label, pull it in the direction of the arrow, and tear the label.

ABCDEFG

abcdefg

1234567

ABCDEFG abcdefg

1234567

■ When the next label is not printed

1 With the printer online, press the

PRINT button to take the printer offline (STATUS LED turns off).

2 Press the FEED button to feed

the labels.

12345

ABCDEF abcdefg

113

Printing

* The number of labels that can be printed with one battery pack differs between

continuous printing mode and dispense mode printing.

* When the non-separated labels are severed somewhere other than the perforated line,

and the next label is not printed, perform the operations on page 29.

3 When the paper stops, pull it in

the direction of the arrow to cut the label.

4 Press the PRINT button to put

the printer online (STATUS LED lights green).

PRINT button

FEED button

ABCDEFG

abcdefg

1234567

ABCDEFG abcdefg

Printing

1234567

Page 19

.Troubleshooting

The status of this printer is indicated by the STATUS LED display and a buzzer sound. When the STATUS LED display or buzzer indicates the status below, the

printer is in an abnormal condition. Clear the error using the clearing method. The printer will automatically turn off in about 30 seconds after a low battery display appears. Confirm that the power is off, then remove the battery pack and charge it.

STATUS LED/buzzer

LED: ON (red) LED: Blinking (red) every 2 seconds

Buzzer: One long beep

LED: ON (red)

Troubleshooting

LED: Two colors blinking alternately (green ➝ red) every 2 seconds Buzzer: One long beep

LED: Blinking (red) every 0.5 seconds Buzzer: Three short beeps

LED: Blinking (green) every 1 second Buzzer: One long beep

LED: Blinking (green) every 0.5 seconds Buzzer: One long beep

LED: Blinking (red) every 4 seconds Buzzer: One long beep

LED: Blinking (green) every 2 seconds

LED: Patterned lighting (red ➝ OFF ➝ green ➝ OFF) every 1 second

LED: Two colors blinking alternately (green ➝ orange) every 0.5 seconds

Mode

All modes Online

After turning power on

Online

Online (printing or receiving data)

All modes

Online (automatic dispenser printing or dispenser operation 2)

Content

Low battery Module error (Bluetooth or

wireless LAN) 1 Program abnormality

error 2 FLASH ROM error

Head error

Cover open Out of paper Sensor error

Communication error

Buffer almost full

Buffer overflow

Sleep mode

Head overheating protection function

Manual dispensing mode

Cause

1 The battery is not fully charged. 1 Interface module is in abnormal condition.

(Bluetooth or wireless LAN) 1 A FLASH ROM reading/writing error has

occurred.

1 The head has a broken wire.

1 The cover is not locked.

Cover opening/closing sensor is in abnormal condition.

2 1 Out of labels.

1 The sensor level is incorrect. 2 The sensor type is incorrect. 3 The paper is misrouted.

The communication conditions are incorrect.

1 2

Cable connection is in abnormal condition.

1 The receiving buffer is running out of capacity.

1 Data has exceeded the receiving buffer capacity. 2 The communication conditions are incorrect. 1 This is not an error. The printer is operating in low power consumption mode.

1 This is not an error.

The head overheating protection function operates

when the head temperature exceeds 70°C.

1 This is not an error. 2 Press the PRINT button to print one label.

1 Charge the battery. 1 Replace the board.*

1 Replace the FLASH ROM.* 2 Re-download the program.*

1 Replace the head.*

1 Lock the cover. 2 Adjust the sensor.*

1 Set a new roll of label. 1 Adjust the sensor level.*

2 Match the sensor type. 3 Remove the label roll and place it correctly.

1 Correct the communication conditions. 2 Check the cable connections.

1 Pause host data transmission, wait for the

1 Transmit data corresponding with the 2 Correct the communication conditions.

1 Clear by pressing a button, receiving data,

1 This is cleared when the head temperature

1 Automatically cleared when the designated

Clearing method

Troubleshooting

buffer to empty, then retransmit data.

communication conditions.

or opening/closing the main cover.

falls to 55°C.

number of labels are printed.

* : Contact your nearest service center or retail store.

Page 20

■ When printing fails (automatic printing)

In direct sunlight or under illumination, the internal sensors may mis-operate (assuming a label is present in the dispenser unit), and prevent printing. In such malfunction, either shield the dispenser unit from harsh light, or operate using one of the following methods.

1 Operation using manual printing

Switch to manual printing by specifying the dispenser operation mode. (See P. 43)

2 Operate using operation 2 for the dispenser operation

Using the printer setup tool, switch the dispenser operation to operation 2.

Troubleshooting

Smudged

When operation 2 is set for the printing, print using the following procedure.

Press the PRINT button to switch to manual printing, and print one label. When printing multiple labels, operate with manual printing until the designated number of labels are printed.

While operating in manual printing mode, the STATUS LED alternates between lighting green and orange (every 0.5 seconds).

Print condition

1 The head is dirty. 2 The rollers are dirty.

dispenser

Cause

operation, if harsh light is preventing

Countermeasures

1 Clean the head (See P. 33). 2 Clean the platen (See P. 34).

. Daily Care

Be sure to turn the power off and remove the battery pack before performing the following operations.

■ Caring for the thermal head

1 Slide the cover release lever to

open the cover.

When in dispense mode printing, first slide the dispenser unit to the continuous printing mode position. (See P. 21)

2 Wipe off any smudges with a

cloth dipped in alcohol.

* Do not use thinner, benzene, or

kerosene.

Daily Care

Vertical stripes

Characters printed diagonally

Blank (not printed)

* : Contact your nearest service center or retail store.

1 The head is dirty. 2 The head is defective.

1 The label guide position

is incorrect.

2 The rollers are dirty. 1 The RS-232C/USB

cable connection is poor.

2 Infrared communication

error.

3 Bluetooth/wireless LAN

communication error.

4 The DIP switch settings

are incorrect.

5 The head is defective.

1 Clean the head (See P. 33). 2 Replace the head.*

1 Reset the label (See P. 17). 2 Clean the platen (See P. 34).

1 Check the RS-232C/USB cable

connections (See P. 24 and 25).

The distance between the PC and the

printer should be within 15-20 cm. In addition, check that the PC is within a 30° area vertically and horizontally (cone shape) from the center of the printer infrared communication sensor (See P. 26).

3 Check all settings. 4 Check the DIP switch settings

(See P. 48).

5 Replace the head.*

Dispenser roller

Page 21

■ Caring for the platen/ dispenser roller/paper sensor

1 Slide the cover release lever to

open the main cover.

When in dispense mode printing, first slide the dispenser unit to the continuous printing mode position. (See P. 21)

. Reference

Included Items

• Shoulder belt

This belt allows you to carry the printer on your shoulder.

2 Wipe off any smudges with a

Daily Care

cloth dipped in alcohol.

* Do not use thinner, benzene, or

kerosene.

Paper sensor

Dispenser roller

Platen

1 Thread the shoulder belt through

the belt holes on the printer, from the outside to the inside.

2 Thread the end of the shoulder

belt through the buckle, and adjust the length.

* If the belt is not routed correctly, the

belt may detach and the printer may drop.

Options

User options

• Battery pack (one pack provided with this printer)

Having extra batteries available will minimize work interruptions caused by depleted batteries.

Reference

Page 22

•Battery charger (single)

This charges a single battery pack.

Reference

• Battery charger (quintuple)

This charges multiple battery packs (maximum of five).

• Shoulder case with rainproof cover

This is a version of the Belt case that has a rainproof cover.

Fastening method

1 Open the cover and place the printer in with the operating parts facing up.

Reference

•AC adapter for printer

Use this to supply power from a household power outlet (AC100V or 240V). Connect the DC output terminal of the AC adapter to the printer.

• Be sure to use the specified adapter.

• Hold the printer when connecting or disconnecting.

• Be careful not to damage the cord.

• Unplug for storage when not in use.

• The AC adapter set provided for this printer is specific to this printer. Do not use it for other electric equipment.

2 Place the lower side in the case

so that the printer is completely in the case.

3 Close the cover.

Page 23

4 Affix the rainproof cover to the Belt case with the buttons and set in place.

Rainproof cover

5 Attach the shoulder strap to the rainproof case.

Reference

Shoulder strap

• Belt case

This protective case is for carrying the printer by attaching it to your belt.

Fastening method

Belt case

1 Open the cover and place the printer in with the operating parts facing up.

2 Place the lower side in the case

so that the printer is completely in the case.

3 Close the Belt case cover.

Reference

4 Run a belt through the Belt case.

• RS-232C cable

This connects with a PC or handheld terminal.

• USB cable

This connects with a PC or handheld terminal.

Manufacturer options

•Wireless LAN interface operating panel (with LCD)

This is an operating panel with an LCD to display the wireless communication status.

Page 24

Operation Modes

Normal operation mode

There are two printer operation modes: continuous printing mode, and dispense mode printing. Test printing and online printing are available in both modes.

Continuous printing

Test printing Prints the printer status

Reference

Continuous printing

* Use the printer setting tool to set dispense mode printing (non-separated labels).

Online printing

(Receives data from a PC or handheld terminal and prints it)

1234567

ABCDEFG

abcdefg

1234567

ABCDEFG abcdefg

Dispenser printing

(label paper)

1234567

ABCDEFG

abcdefg

Dispenser printing

Continuous printing

Dispenser printing

(non-separated labels)

ABCDEFG

1234567 abcdefg

POWER ON

POWER

Online

PRINT button

The LED display for the normal operation mode is as follows.

Starting normal printing mode ON (orange) Online ON (green) Offline OFF

* When the buzzer sound mode is enabled, the buzzer sounds upon startup.

The battery life indicator remains on even when the printer is OFFLINE.

PRINT button

Offline

Operation status STATUS (LED)

FEED button

Feed paper

Power saving mode

1. Sleep mode:

With the printer online, the STATUS (LED) blinks (green) every two seconds. When offline, the ST ATUS (LED) is off. The battery life indicator (LED) remains on even when the printer is OFFLINE. The printer enters sleep mode (standby status) when it has not been operated for five seconds. Normal status is resumed by pressing the PRINT button or the FEED button, by receiving data, or by opening and closing the main cover.

Reference

Page 25

Test printing mode (FEED button + POWER ON)

POWER ON

FEED button + POWER

Start test printing

FEED button

Reference

Test printing

FEED button

Stop printing

The LED display for the test printing mode is as follows.

Operation status STATUS (LED)

Starting test printing mode ON (orange) Test printing initializing Blinking (green) Test printing ON (green) Stop printing OFF

* When the buzzer sound mode is enabled, the buzzer sounds upon startup.

Release the FEED button to stop the buzzer.

Dispense mode printing Dispense mode printing setting

Type

Automatic printing setting

Manual printing setting

Prints one label after receiving data, then waits for label to be peeled. After the label is peeled, the next label is printed automatically.

Prints one label after receiving data, then enters offline status. When the PRINT button is pressed, the next label is printed. After the specified number of labels are printed, printing is ended, and no labels are printed when the PRINT button is pressed.

Operation

Changing the dispense mode printing setting

The

dispenser power is turned on, and by off.

operation mode setting is changed by the DIP switch (DSW) settings when the

1 Automatic dispenser printing setting DSW-1,2,3,4=(OFF,OFF,OFF,ON) + cover open+ PRINT button + POWER 2 Manual dispenser printing setting DSW-1,2,3,4=(OFF,OFF,OFF,ON) + cover open + FEED button + POWER

Processing dispenser operation mode setting (STATUS LED flashes green)

Setting completes (STATUS LED lights green)

button

settings. The settings are enabled upon turning the power

Default

Manual printing setting

Reference

Note: When the buzzer sound mode is enabled, the buzzer sounds upon startup.

Release the PRINT/FEED button to stop the buzzer. To end the dispenser operation mode setting, confirm that the STATUS LED is on in green, then turn the power off. After changing the dispenser operation mode setting, be sure to restore the DSW to their original settings.

Page 26

Head check setting mode

In the head check setting mode, a check can be performed in two checking areas: the printing area and the barcode printing area. The presence of the head check function and the head check range settings are set by the DIP switch (DSW) settings when the power is turned on, by button pressing status, and by the cover status.

DIP switch settings

Reference

(A) (B)

DSW

settings

(A)

(B)

DSW-1

Button and cover status

PRINT button + cover open

FEED button + cover open PRINT button + cover open

FEED button + cover open

OFF

DSW-2

OFF

DSW-3

DSW-4

OFF OFF

ON ON

Function

Head check range set as printing area

Head check function set as disabled Head check range set as barcode

printing area only Head check function set as disabled

Default

Head check range set as printing area

Online command setting mode Online command setting details

Type

MB400 compatibility command setting

SBPL command setting

Sets the online command as standard legacy command (of the MB200/400 series).

Sets the online command as an SBPL command.

Operation

Default

SBPL command setting

Change online command setting

The online command setting is changed by the DIP switch (DSW) settings when the power is turned on, and by button settings. The settings are enabled upon turning the power off.

1 MB400 compatibility command setting DSW-1,2,3,4=(ON,ON,ON,ON) + cover open + PRINT button + POWER 2 SBPL command setting DSW-1,2,3,4=(ON,ON,ON,ON) + cover open + FEED button + POWER

Processing setting (STATUS LED flashes green)

Reference

DSW settings (A/B) + cover open + PRINT/FEED button + POWER

Setting head check function (STATUS LED flashes green)

Setting completes (STATUS LED lights green)

Note: When the buzzer sound mode is enabled, the buzzer sounds upon startup.

Release the PRINT/FEED button to stop the buzzer. To check the settings for head check setting mode, see the test print output (See P. 23). To end head check setting, confirm that the STATUS LED is on in green, then turn power off. After changing the head check setting mode, be sure to restore the DSW to their original settings.

Settings complete (STATUS LED lights green)

Note: When the buzzer sound mode is enabled, the buzzer sounds upon startup.

Release the PRINT/FEED button to stop the buzzer. To check the settings for the online command setting mode, see the test print output (See P. 23). To end online command setting, confirm that the STATUS LED is on in green, then turn the power off. After changing the online command setting mode, be sure to restore the DSW to their original settings.

Page 27

Buzzer sound mode setting

A buzzer can be sounded upon starting up the printer and upon errors. The buzzer is enabled by default. This can be enabled or disabled by the initial operation and by online command.

Change buzzer sound setting

1 Disable buzzer sound DSW-1,2,3,4=(OFF,OFF,ON,ON) + cover open + PRINT button + POWER 2 Enable buzzer sound DSW-1,2,3,4=(OFF,OFF,ON,ON) + cover open + FEED button + POWER

Reference

Processing setting (STATUS LED flashes green)

Setting completes (STATUS LED lights green)

Note: When the buzzer sound mode is enabled, the buzzer sounds upon startup.

Release the PRINT/FEED button to stop the buzzer. To check the settings for the buzzer sound setting mode, see the test print output (See P. 23). To end buzzer sound setting, confirm that the STATUS LED is on in green, then turn the power off. After changing the buzzer sound setting mode, be sure to restore the DSW to their original settings.

Standard/non-standard code setting mode

Standard code/non-standard code settings for control codes can be changed using the control code setting command.

Standard/non-standard specifications

Standard code setting

Type

Non-standard code setting

The following control codes are set as standard codes.

Control code Binary

The following control codes are set as non-standard codes.

Control code Binary

* Non-standard codes can be changed using

the user download setting command.

Operation

STX 02H

ETX 03H ESC 1BH ENQ 05H CAN 18H

NULL 00H

STX 7BH({)

ETX 7DH())

ESC 5EH(^) ENQ 40H(@) CAN 21H(!)

NULL 7EH(~)

Default

Standard code setting

Change standard/non-standard code setting

The standard code/non-standard code setting is changed by the DIP switch (DSW) settings when the power is turned on, and by button settings. The settings are enabled upon turning the power off.

1 Non-standard code setting DSW-1,2,3,4=(ON,ON,OFF,ON) + cover open + PRINT button + POWER 2 Standard code setting DSW-1,2,3,4=(ON,ON,OFF,ON) + cover open + FEED button + POWER

Reference

Processing setting (STATUS LED flashes green)

Setting completes (STATUS LED lights green)

Note: When the buzzer sound mode is enabled, the buzzer sounds upon startup. Release

the PRINT/FEED button to stop the buzzer. To check the settings for the standard code/non-standard code setting mode, see the test print output (See P. 23). To end standard code/non-standard code setting, confirm that the STATUS LED is on in green, then turn power off. After changing the standard code/non-standard code setting mode, be sure to restore the DSW to their original settings.

Page 28

DIP Switch

• Setting DIP switch

1 Turn the power OFF.

2 Open the DIP switch cover.

3 Use a pointed object, such as the

tip of a ballpoint pen, to change

Reference

the switch position.

• DIP switch setting items

DIP switch Startup modeButton

OFF

2341

OFF

Cover

CLOSE CLOSE CLOSE

OPEN OPEN OPEN OPEN

OPEN OPEN

CLOSE CLOSE

OPEN

CLOSE CLOSE

OPEN

OPEN OPEN

OFF OFF OFF

OFF

ON OFF OFF

OFF

ON OFF OFF

OFF OFF

ON OFF

OFF OFF

OFF

ON OFF

FEED

OFF

ON OFF OFF

ON OFF

OFF

ON OFF

OFF

OFF OFF

ON OFF

OFF

Interface

RS-232C – RS-232C – – – – Bluetooth interface Wireless LAN interface – – – Bluetooth interface Wireless LAN interface – – Infrared interface – Infrared interface –

– USB interface – USB interface –

–

– –

Content

Normal printing mode User test printing mode HEX dump mode Buzzer sound disabled Buzzer sound enabled Automatic dispenser printing setting Manual dispenser printing setting Normal printing mode

Reference

User test printing mode Head check (printing area) setting Head check disabled HEX dump mode

CRC check enabled CRC check disabled Normal startup mode

Test printing mode HEX dump mode

Head check (Barcode printing area) setting Head check disabled Normal operation

Test printing mode HEX dump mode

Online command setting (compatible with MB400) Online command setting (SBPL command) Non-standard code setting Standard code setting

Page 29

Basic Specifications of MB400i/MB410i

Printing method Head density Maximum effective printing area

Printing speed

Dimensions Weight Power source (battery)

Reference

Paper Paper thickness Paper shape

Label size (backing liner and eye-mark pitch)

Label printing

Self-diagnosis function Low power consumption function

Interface

• RS-232C

• USB

• Optical coupling

•Bluetooth option

• Wireless LAN option

Paper sensor

Item

Thermal printing 8 dots/mm (203 dpi) 12 dots/mm (305 dpi) 104 mm (width) × 297 mm (pitch) Maximum 103 mm/sec. (printing speed is 75 mm/sec. during dispenser printing). Differs depending on printing rate and usage environment. Printing speed can be changed using the printing speed setting command. 170 mm (width) × 76 mm (depth) × 134 mm (height) (excluding protruded parts) 750 g or less (Standard specifications; including the battery pack) Pack type (lithium ion) 1700 mAh can continuously print four rolls of thermal labels (equivalent to 50 m) when fully charged (however, at a printing rate of 16% or less). Always use genuine SATO labels.

0.064 mm to 0.190 mm Roll media: Face-out winding Maximum outer diameter: φ 58 mm Standard Width 50 to 111 mm (53 to 114 mm)

Dispenser Width 50 to 111 mm (53 to 114 mm)

Non-separated Width 53 to 107 mm

Continuous printing (Paper sensor enabled) Dispenser printing (Paper sensor enabled) Journal printing (Paper sensor disabled) Non-separated printing (Paper sensor enabled) Label printing can be changed using the printer command <PG>. Head check/battery check/paper out/cover open/test printing Enters sleep mode after five seconds of non-activity (button press, data reception or cover operation). Automatically powers off after five minutes of continued non-activity. Note: The default setting for the Bluetooth or the wireless LAN models is to disable automatic power-off. The automatic power-off time can be changed using the <PG> printer operation command. For command details, see the programming guide.

Mini DIN (specified) mini B type Infrared communication (compliant with IrDA Standard Ver 1.2) Bluetooth Specification Ver1.1 Class2 Wireless LAN interface (IEEE 802.11b/g) TCP/IP (FTP, LPR, SOCKET) Reflective sensor (I-mark), transmission type (gap)

MB400i MB410i

Pitch: 25 to 297 mm (28 to 300 mm)

Pitch: 25 to 182 mm (28 to 185 mm)

Pitch: 28 to 182 mm

Character magnification

Item

Character rotation

Fonts

Barcode

2-D code

Switch Display

Buzzer Safety or Noise standard

Protective circuit

Water resistance

Environment conditions (including battery pack)

Options

1 to 6 times

MB400i MB410i

0°, 90°, 180°, 270° SATO standard fonts: ×20, ×21, ×22, ×23, ×24, OCR-A, OCR-B, POP fonts Kanji 16 × 16, 22 × 22, 24 × 24 square Gothic (JIS level-1 and level-2 set), Mark-down fonts JAN/EAN8, JAN/EAN13, UPC-E/UPC-A, NW-7, CODE39, CODE93, CODE128, INTERLEAVED 2 of 5, customer barcode, RSS-14 * However, barcodes are to be used at:

Parallel barcode: thin bar width 2 dots or more

Serial barcode: thin bar width 3 dots or more PDF417, QR code (includes micro QR), Data matrix code (ECC200), MAXI code, composite symbols POWER button, PRINT button, FEED button STATUS LED: 1 (lights in three colors: green, red, and orange) Battery remaining power display LED : Printer status information buzzer FCC15B, FCC15C, EN55022, EN55024, EN61000-3-2, EN61000-3-3, GB4943, GB9254, GB17625.1 Overcharging prevention, over-discharging prevention, head overheating protection function, low battery detection Meets IPX3 JIS C0920-2003 When using waterproof case (option) * Excludes when communication cable is connected. Operating ambient temperature :

Humidity : 20 to 80% Non-condensing

Storage ambient temperature : -25 to 60°C

Humidity : 20 to 80% Non-condensing

Excludes paper environment Battery pack, AC adapter, battery charger (single), waterproof case, belt case, RS-232C cable, USB cable

3 (lights in two colors: green and red)

-15 to 50°C (for wireless LAN: 0 to 50°C)

Reference

Page 30

Sato MB400I B1, MB400I W2 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual