UHF Inlay Configuration Guide
In order to successfully configure your CL4NX UHF printer,
you will need the following information about your label.
I-Mark
X: Liner Edge to Center of Chip
Y: Optimum Encoding Position*
S: Minimum Inlay Separation
*Y: Measured from tail edge of I-mark to lead edge of inlay when
I-mark sensor is used.
Measured from lead edge of label to edge of inlay when Gap
sensor is used.
Feed direction will affect encoding.
This is signified using the inlay
images in the following table.
Region
Manufacturer
Alien
Technology
Alien
Technology
Alien
Technology
Inlay
[IC Chip]
ALN-9640 Squiggle
[Alien Higgs3]
ALN-9662 Short
[Alien Higgs3]
ALN-9762 Short
[Alien Higgs4]
Feed Direction
Position(mm) Power (dBm)
XYSWriteRead
47.5-57 3-5 21 24 14 Short - - -
47.5-57 18-36 33 16 7 Standard
35-45 0-5 23 24 18 Short - - -
35-65 10-24 50 24 16 Standard
50-60 0-5 20 24 13 Short - - -
50-60 15-22 43 24 10 Standard
Standard Antenna Position determined by value of Y.
When Antenna Pitch is “Short”, Standard Antenna Position
can be set to any position; “Blue”, “Yellow”, or “Green”.
(Y=) Standard Antenna Position
Antenna
Pitch
The value of “Y” will affect printer configuration of
Antenna Selection and Antenna Position.
(mm)
Blue Yello w Green
18-23 24-29 30-36
10-14 15-20 21-24
15-18 19-22 -
CL4NX UHF Inlay Placement & Configuration Table
This recommendation has been tested successfully at SATO. Results may vary in the actual customer installation due to overall system tolerances. Validation of
functionality in the actual system is therefore recommended.
In no event shall SATO be liable for any faults arising out of use of or inability to use the product.
Placement and Configurations
globally valid with minor variation.
Valid for Frequencies that fall
within the FCC range, 902-928MHz
Region
Manufacturer
Alien
Technology
Alien
Technology
Alien
Technology
Alien
Technology
Alien
Technology
Alien
Technology
Alien
Technology
Alien
Technology
Alien
Technology
Alien
Technology
Alien
Technology
Arizon
Avery
Dennison
ALN-9640 “Squiggle”
[Alien Higgs3]
ALN-9662 “Short”
[Alien Higgs3]
ALN-9762 “Short”
[Alien Higgs4]
ALN-9610 “Squig”
[Alien Higgs3]
ALN-9710 “Squig”
[Alien Higgs4]
ALN-9720 “HiScan”
[Alien Higgs4]
ALN-9654 “G Tag”
[Alien Higgs3]
ALN-9728
“Garment Tag”
[Alien Higgs4]
ALN-9728-90
“Garment Tag”
[Alien Higgs4]
ALN-9730 "Squiglette"
[Alien Higgs 4]
ALN-9630 "Squiglette"
[Alien Higgs 3]
[Alien Higgs4]
AD-110m5
[Impinj Monza5]
Inlay
[IC Chip]
AZ-9762
Feed Direction
The arrow in the header of table
indicates the direction in which labels
are output from the printer.
Feed Direction
Position(mm) Power (dBm)
XYSWriteRead
(Y=) Standard Antenna Position
Antenna
Pitch
Blue Yel low Green
(mm)
47.5-57 3-5 21 24 14 Short - - -
47.5-57 18-36 33 16 7 Standard
18-23 24-29 30-36
35-45 0-5 23 24 18 Short - - -
35-65 10-24 50 24 16 Standard
10-14 15-20 21-24
50-60 0-5 20 24 13 Short - - -
50-60 15-22 43 24 10 Standard
15-18 19-22 -
22.5-42 2-5 21 24 13 Short - - -
22.5-62 15-24 85 24 15 Standard
15-18 19-24 -
22.5-62 3-6 21 24 15 Short - - -
22.5-37 14-28 80 23 20 Standard 14-18 19-24 25-28
19.5-59 0-3 31 24 18 Short - - -
34.5-59 14-32 80 24 17 Standard 14-17 18-24 25-32
46.5-56.5 1-10 25 20 17 Short - - -
46.5-61.5 14-30 58 14 10 Standard
14-18 19-24 25-30
22.5-37.5 0-5 36 23 15 Short - - -
22.5-62.5 6-19 105 24 18 Standard
6-9 10-14 15-19
- - - - - Short - - -
15-35 24-37 85 18 10 Standard
- 24-30 31-37
- - - - - Short - - -
55 17-24 26 24 11 Standard
17-20 21-24 -
40-55 0-4 22 24 16 Short - - -
40-70 15-33 59 24 17 Standard
15-23 24-28 29-33
35-50 0-3 25 24 19 Short - - -
40-65 11-36 48 24 17 Standard
11- 19 20-28 29-36
21.5-46.5 4-11 22 24 16 Short - - -
36.5-46.5 11-32 65 24 20 Standard 11 -17 18-25 26-32
First edition: Mar 2014 Q04502000
©2014 SATO CORPORATION
Region
Manufacturer
Avery
Dennison
Avery
Dennison
Avery
Dennison
Avery
Dennison
Avery
Dennison
Avery
Dennison
Avery
Dennison
Inlay
[IC Chip]
AD-171m5
[Impinj Monza5]
AD-227m5
[Impinj Monza5]
AD-232iL
[NXP UCODE G2iL]
AD-233m5
[Impinj Monza5]
AD-235u7
[NXP UCODE 7]
AD-318m5
[Impinj Monza5]
AD-370u7
[NXP UCODE 7]
Feed Direction
Position(mm) Power (dBm)
XYSWriteRead
13.5-53.5 7-10 18 24 16 Short - - -
13.5-23.5 11-35 60 24 19 Standard
47.5-57.5 0-10 31 24 19 Short - - -
47.5-57.5 13-36 38 16 11 Standard
- - - - - Short - - -
45-70 12-35 62 24 16 Standard
40-55 0-4 24 24 19 Short - - -
40-70 15-37 63 23 17 Standard 15-21 22-29 30-37
35-50 0-5 20 24 12 Short - - -
35-65 10-40 59 19 12 Standard
21-46 0-3 31 24 19 Short - - -
31-61 11-31 52 23 19 Standard
- - - - - Short - - -
18.5-48.5 67-90 86 17 14 Standard
(Y=) Standard Antenna Position
Antenna
Pitch
Blue Yel low Green
11- 18 19-27 28-35
13-20 21-28 29-36
12-19 20-27 28-35
10-20 21-30 31-40
11- 17 18-24 25-31
67-79 80-90 -
(mm)
Avery
Dennison
Avery
Dennison
Avery
Dennison
SMARTRAC
SMARTRAC
SMARTRAC
SMARTRAC
SMARTRAC
SMARTRAC
SMARTRAC
SMARTRAC
SMARTRAC
SMARTRAC
SMARTRAC
SMARTRAC
Invengo
Invengo
CHECKPOINT
CHECKPOINT
AD-224iL
[NXP UCODE G2iL]
AD-317iL
[NXP UCODE G2iL]
AD-236u7
[NXP UCODE 7]
DogBone i
[NXP UCODE G2iL/iM]
Short Dipole i
[NXP UCODE G2iL/iM]
Short Dipole M4
[Impinj Monza4
(E/D/QT)]
Belt M5
[Impinj Monza5]
MiniWeb
[NXP UCODE G2iL/iM]
Web I
[NXP UCODE G2iL]
WebLite
[Impinj Monza5]
Viper
[Impinj Monza4D]
Frog 3D
[Impinj Monza4
(E/D/QT)]
Belt
[NXP UCODE G2iL]
Dogbone
[Impinj Monza 5]
ShortDipole
[Impinj Monza 5]
Invengo Great Wall
[Impinj Monza5]
Invengo xWing
[Impinj Monza5]
Champion-M5
[Impinj Monza5]
WindAparrel-M5
[Impinj Monza5]
47.5-57.5 0-10 24 24 19 Short - - -
47.5-62.5 16-37 41 24 15 Standard 16-22 23-29 30-37
- - - - - Short - - -
35.5-60.5 10-33 50 24 16 Standard
40-70 0-7 24 24 16 Short - - -
40-50 8-31 37 18 8 Standard
- - - - - Short - - -
44-59 1-30 50 24 9 Standard
- - - - - Short - - -
46.5-56.5 14-34 45 24 11 Standard
46.5-56.5 0-1 16 24 13 Short - - -
46.5-56.5 12-36 48 24 15 Standard
35-40 0-3 23 24 16 Short - - -
40-70 11-35 60 24 13 Standard
- - - - - Short - - -
45-60 18-35 47 24 12 Standard
17.5-22.5 5-8 61 24 12 Short - - -
12.5-27.5 34-49 93 24 12 Standard
23-33 0-5 36 24 23 Short - - -
33-63 14-37 45 23 18 Standard 14-21 22-29 30-37
55 0-10 20 24 16 Short - - -
55 15-35 25 10 7 Standard
25-30 3-6 60 24 19 Short - - -
25-40 7-36 82 20 17 Standard 7-16 17-26 27-36
- - - - - Short - - -
50-55 16-36 41 24 15 Standard
- - - - - Short - - -
43-58 13-31 36 8 8 Standard
46-56 0-3 19 20 18 Short - - -
46-61 20-34 31 10 9 Standard
47-62 0-2 30 24 20 Short - - -
47-57 11-37 36 18 15 Standard
34.5-49.5 2-4 25 24 18 Short - - -
39.5-64.5 7-34 54 20 19 Standard
40-45 0-2 27 24 19 Short - - -
40-70 8-35 58 20 20 Standard
30-45 8-11 46 23 20 Short - - -
30-65 19-41 82 16 13 Standard
10-17 18-25 26-33
8-15 16-23 24-31
1-10 11- 20 21-30
14-20 21-27 28-34
12-20 21-28 29-36
11- 18 19-26 27-35
18-23 24-29 30-35
- 34-41 42-49
15-21 22-28 29-35
16-22 23-29 30-36
13-19 20-25 26-31
20-24 25-29 30-34
11- 19 20-28 29-37
7-15 16-24 25-34
8-16 17-25 26-35
20-26 27-34 35-41
For inlays not included on this list, please contact your local SATO dealer or sales office.
www.satoworldwide.com
• Squiggle and Higgs are trademarks or registered trademarks of Alien Technology Corporation in the U.S. and other countries.
• Monza is registered trademark of Impinj, Inc.
Loading...