Sanyo DP32D13 Quick Start Manual

QUIK ‘N EASY

Setup Guide

Simple step by step procedures for correct HD hookups and initial setup process.

Attach the Stand Base to the HDTV.

For additional information, consult your HDTV’s owner’s manual.

Hookup your Audio/Video equipment to the HDTV.

Use Component or HDMI connections, and a High Definition source for the best picture possible. Your AV equipment Output Jacks must be connected to the HDTV’s Input Jacks. Always match the color of the jacks and connectors.

Hook up your antenna or direct Cable service.

An indoor antenna should be placed at least 3 ft away from the HDTV.

ANTENNA OR CABLE

HDTV’s side panel

CONNECTION TYPE CABLE/CONNECTOR IMAGE QUALITY

Off-air HD signal or Digital Cable

HDMI

BEST

BETTER

Component

GOOD

Composite

For the best HD experience, be sure to use HD devices and/or HD off-air signals transmitting HD content.

HDTV’s bottom panel

COMPONENT/AV IN may be used with either Composite or Component cables.

NOTE: See owner’s manual for more details

Connect the AC cord to power outlet.

Finalize the completed Setup process.

Use the POWER key to turn on your HDTV.

Aim Remote at the lower left corner of the HDTV.

Use the Setup Wizard to select your HDTV’s location.

For the first time after powering on your HDTV, the Setup Wizard appears. Press the CURSOR UP/DOWN key to select Home Mode or Shop Mode.

Setup Wizard (1/5)

Please select Home/Shop

Home Mode

Shop Mode

Home mode default settings are recommended for

in-home use. ENERGY STAR

Shop mode is intended for in-store display and resets

video settings at Power On.

Cancel

Move

ENTER

qualified.

Select

Please allow the HDTV a few minutes to complete the process. Use the EXIT key to finish the Setup Wizard. You can now watch and enjoy TV programming on your HDTV!

Setup Wizard (4/5)

Searching. Please wait

Searching CH

Digital Channels Found

Analog Channels Found

50%

ENTER

Channel 4

Cancel

Select

Setup Wizard (5/5)

Congratulations. TV Setup is done.

Exit

EXIT

Choose the correct Input source.

Use the INPUT key on your remote control to select from the available Input sources on your HDTV.

NOTE: If you receive Satellite or Cable service through a set top box, tune to the correct input on your HDTV and use the receiver and its remote for channel viewing.

Si necesita ayuda en ESPAÑOL, marque al 1-800-877-5032 y un asesor estará dispuesto a ofrecerle ayuda con cualquiera de sus dudas.

NOTE: Selecting Home Mode will qualify as an Energy Star rating.

Perform a Signal search.

Press the CURSOR UP/DOWN key to select Antenna, Cable, or Set Top Box.

Press the CURSOR ENTER key to enter the next step, and then start a

Channel search for digital and analog channels. Please allow the HDTV a few minutes to complete the process.

Setup Wizard (2/5)

Please select TV RF tuning band

Antenna

Cable

Set Top Box

P revious Cancel

Move Select

HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

ENTER

Setup Wizard (3/5)

Please check that the RF cable is connected properly. Scan time may take over 20 minutes.

START

P revious Cancel

Move Select

ENTER

Use the following codes to program your cable or satellite provider’s remote control to work with your new HDTV.

Direct TV Dish Network Comcast Cox Verizon ATT

10154, 960

590, 683, 589, 542, 652 10154 0154, 0088 0181, 0826, 0920 1045, 1062, 1095, 1380

(to activate INPUT feature)

NOTE: If these do not work, refer to your Cable or Satellite manual.