Samsung SyncMaster 151B, SyncMaster 151BM, SyncMaster 151Q, SyncMaster 151S, SyncMaster 151V Owner Manual

SyncMaster 151S/151B/151BM/151V/151Q

Index

Main Page On-Screen Display

Safety Instructions Troubleshooting

Notational Check List

Power Q & A

Installation Self-Test Feature Check

Cleaning

Other

User’s Manual

Introduction Specifications

Unpacking General Specifications

Front PowerSaver

Rear Preset Display Modes

Setup Information

Connecting Your Monitor Service

Installing the Monitor Driver Terms

—

Automatic Regulatory

—

Manual Natural Color

Installing VESA compliant mounting

For Better Display

Authority

Safety Instructions

Notational

Warning/Caution

User’s Manual

Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment.

Notation Conventions

Prohibited Important to read and understand at all times

Do not disassemble Disconnect the plug from the outlet

Do not touch Grounding to prevent an electric shock

Safety Instructions

Power

When not used for extended periods of time, set your PC to DPMS. If using a screen saver, set it to the active screen mode.

If the size of your monitor is small, or if the same image is present for long periods of time, you may see afterimages due to damage to the flourescent substance on the inside of the TFT-LCD.

User’s Manual

•

Do not use a damaged or loose plug.

•

This may cause an electric shock or fire.

Do not pull the plug out by the wire nor touch the plug with wet hands.

•

This may cause an electric shock or fire.

Use only a properly grounded plug and recepticle.

•

An improper ground may cause electric shock or equipment damage

•

Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage.

•

Failure to do so may cause an electric shock or fire.

Safety Instructions

Power

User’s Manual

•

Disconnect the plug from the outlet during storms or lightening or if it is not used for a long period of time.

•

Failure to do so may cause an electric shock or fire.

Do not connect too many extension cords or plugs to an outlet.

•

This may cause a fire.

Safety Instructions

Installation

User’s Manual

•

Do not cover the vents on the monitor cabinet.

•

Bad ventilation may cause a breakdown or fire.

Put your monitor in a location with low humidity and a minimum of dust.

•

An electric shock or fire could result inside the monitor.

Do not drop the monitor when moving it.

•

This may cause damage to the product or human body.

•

Place the monitor on a flat and stable surface.

•

The monitor can cause injury by falling.

Set down the monitor carefully.

•

It could be damaged or broken.

Safety Instructions

Installation

User’s Manual

•

Do not place the monitor face down.

•

The TFT-LCD surface may be damaged.

Safety Instructions

Clean

When cleaning the monitor case or the surface of the TFT-LCD, wipe with a slightly moistened, soft fabric.

User’s Manual

•

Do not spray detergent directly on the monitor.

Use the recommended detergent with a smooth cloth.

If the connector between the plug and the pin is dusty or dirty, clean it properly with a dry cloth.

•

A dirty connector can cause an electric shock or fire

•

Do not set a glass of water, chemicals or any small metal objects on the monitor.

•

This may cause damage, electric shock or a fire.

•

If a foreign substance gets into the monitor, disconnect the plug and then contact a service center.

Safety Instructions

Other

User’s Manual

•

Do not remove cover(or back). No user serviceable parts inside.

•

This may cause an electric shock or a fire.

•

Refer servicing to qualified service personnel.

If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact an authorized deal er or service.

•

This may cause an electric shock or a fire.

Do not place any heavy objects on the monitor.

•

This may cause an electric shock or a fire.

•

For each hour of looking at the monitor, you should let your eyes rest for 5 minutes.

•

This will reduce eye fatigue.

Do not use or store inflammable substances near the monitor.

•

This may cause an explosion or fire.

Safety Instructions

Other

User’s Manual

•

Do not try to move the monitor by pulling on the wire or the signal cable.

•

This may cause a breakdown, electric shock or a fire due to damage to the cable.

Do not move the monitor right or left by pulling only the wire or the signal cable.

•

This may cause a breakdown, electric shock or a fire due to damage to the cable.

Never insert anything metallic into the monitor openings.

•

This may cause an electric shock, fire or injury.

Introduction

Unparking

•

Monitor and Stand

SyncMaster 151S/151B/151V/151Q

•

Power Cord

•

Signal Cable

User’s Manual

SyncMaster 151BM

•

Pivot Stand and S/W CD(Option)

•

Audio Cable (SyncMaster 151BM)

•

Quick Setup Guide

•

Warranty Card

(Not available in all locations)

•

User's Guide and Driver Installation CD

Please make sure the following items are included

(Some models include a stand attached. )

with your monitor. If any items are missing,

Please make sure the following items are

included with your monitor. If any items

are missing, contact your dealer.11jk

contact your dealer.

User’s Manual

Introduction

Front

SyncMaster 151S/151B/151V/151Q SyncMaster 151BM

1. Auto button

2. Exit button 3,4. Adjust buttons

5. Menu button

6. Power button

7. Power indicator

Note

See PowerSaver described in the manual for further information regarding power

saving functions. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.

Use this button to auto adjustment direct access.

Use this button to Exit the active menu or the OSD.

These buttons allow you to highlight and adjust items in the menu.

Use this button to open the OSD and activate a highlighted menu item.

Use this button to turn the monitor on and off.

This light glows green during normal operation,

and blinks green once as the monitor saves your adjustments.

Introduction

Rear

User’s Manual

(The configuration at the back of the monitor may vary from product to product.)

1. Power port

2. Signal cable

Note

:Connect the power cord for your monitor to the power port

on the back of the monitor.

:Connect the end of the signal cable to your computer's video port.

(video board, video card or graphics card)

See Connecting Your Monitor for further information regarding cable connections.

Setup

User’s Manual

Connecting Your Monitor

(SyncMaster 151S/151B/151V/151Q)

1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet.

2. Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor.

3. If you are using a Macintosh computer, connect the cable to a Macintosh adapter, and set the pins on your adapter(Adapter not included). A PC-compatible computer does not need an adapter.

Turn on your computer and monitor. If your monitor displays an image, installation is

complete.

Setup

Connecting Your Monitor (SyncMaster 151BM)

User’s Manual

1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet.

2. Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor.

3. If you are using a Macintosh computer, connect the cable to a Macintosh adapter, and set the pins on your adapter(Adapter not included). A PC-compatible computer does not need an adapter.

4. Connect the audio cable for your monitor to the audio port on the back of your computer.

Turn on your computer and monitor. If your monitor displays an image,

installation is complete.

Setup

User’s Manual

When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions as appropriate for the operating system you have.

Prepare a blank disk and download the driver program file at the Internet web site shown here.

Internet web site : http://www.samsung-monitor.com/ (Europe)

http://www.samsungusa.com/monitor (USA)

http://www.sec.co.kr/ (Korea) http://www.samsungmonitor.com.cn/ (China)

Windows ME/98/95

1. Insert CD into the CD-ROM drive.

2. Click "Windows ME/98/95 Driver".

3. Choose your monitor model in the model list, then click the "OK" button.

4. Click the "Install" button in the "Warning" window.

5. Monitor driver installation is completed.

Windows XP/2000

1. Insert CD into the CD-ROM drive.

2. Click "Windows XP/2000 Driver".

3. Choose your monitor model in the model list, then click the "OK" button.

Setup

User’s Manual

4. Click the "Install" button in the "Warning" window.

5. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button.

This monitor driver is under certifying MS logo,and this installation don't damage your system.The certified driver will be posted on Samsung Monitor Homepage

http://www.samsungusa.com/monitor

6. Monitor driver installation is completed.

Setup

Prepare a blank disk and download the driver program file at the Internet web site shown here.

Internet web site : http://www.samsung-monitor.com/ (Europe)

http://www.samsungusa.com/monitor (USA)

http://www.sec.co.kr/ (Korea) http://www.samsungmonitor.com.cn/ (China)

Microsoft® Windows® XP Operating System

1. Insert CD into the CD-ROM driver.

2. Click "Start" —> "Control Panel" then click the "Appearance and Themes" Icon.

User’s Manual

3. Click "Display" icon and choose the "Settings" tab then click "Advanced..".

4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab.

Setup

5. Click "Update Driver.." and select "Install from a list or.." then click "Next" button.

6. Select "Don't search ,I will.." then click "Next" and then click "Have disk".

User’s Manual

7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button.

8. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button.

Thi

tifyi

this installati

Setup

User’s Manual

s monitor driver is under cer

system.The certified driver will be posted on Samsung Monitor Homepage

http://www.samsungusa.com/monitor

9. Click the "Close" button then click "OK" button continually.

10. Monitor driver installation is completed.

ng MS logo,and

on don't damage your

Microsoft® Windows® 2000 Operating System

When you can see "Digital Signature Not Found" on your monitor, follow these steps.

1. Choose "OK" button on the "Insert disk" window.

2. Click the "Browse" button on the "File Needed" window.

3. Choose A:(D:\Driver) then click the "Open" button and then click "OK" button.

1. Click "Start" , "Setting" , "Control Panel".

2. Double click the "Display" Icon.

3. Choose the "Settings" tab and then click "Advanced..".

4. Choose "Monitor".

5. Click "Driver" and then click on "Update Driver.." then click on the "Next" button.

6. Choose "Display a list of the known drivers for this device so that I can choose a

7. Click the "Browse" button then choose A:(D:\Driver).

8. Click the "Open" button, then click "OK" button.

9. Choose your monitor model and click the "Next" button then click "Next" button.

10. Click the "Finish" button then the "Close" button.

How to install

Case1: If the "Properties" button is inactive, it means your monitor is properly configured.

Please stop installation

Case2: If the "Properties" button is active, click the "Properties" button then follow next

steps continually.

specific driver" then click "Next" and then click "Have disk".

If you can see the "Digital Signature Not Found" window then click the "Yes"button. And click the "Finish" button then the "Close" button.

+ 44 hidden pages