Samsung SNP-6201, SNP-6201H User Manual

NETWORK CAMERA

User Manual

SNP-6201/SNP-6201H

Network Camera

User Manual

Trademark

The name of thi s product is the reg istered tradema rk of Samsung Techwin C o., Ltd. Other trad emarks mention ed in this manual are th e registered trad emark of their resp ective company.

Restriction

Samsung Techwi n Co., Ltd shall reser ve the copyrigh t of this document. U nder no circumst ances, this docu ment shall be reproduced, distributed or changed, partially or wholly, without formal authorization of Samsung Techwin.

Disclaimer

Samsung Techwi n makes the best to ver ify the integri ty and correct ness of the conten ts in this document , but no formal guar antee shall be provi ded. Use of this do cument and the subse quent results sha ll be entirely on the u ser’s own responsib ility. Samsung Techwi n reserves the ri ght to change the con tents of this docum ent without prio r notice.

Design and specifications are subject to change without prior notice.

The defau lt password c an be exposed to a h acking thread s o it is recommen ded to change th e password

after in stalling the pr oduct. Note that t he security a nd other relat ed issues caus ed by the unchan ged password s hall be respon sible for the use r.

is the regist ered logo of Samsun g Techwin Co., Ltd.

overview

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings, Install in accordance with the manufacturer’s

instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other

apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized

plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/ accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by

the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lighting storms or when unused for

long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

● OVERVIEW

English _3

overview

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECT THROUGH THE VENTILATION GRILLS OR OTHER OPENNINGS ON THE EQUIPMENT.

Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

To prevent injury, this apparatus must be securely attached to the Wall/ceiling in accordance with the installation instructions.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN

CAUTION

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

: TO REDUCE THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

EXPLANATION OF GRAPHICAL SYMBOLS

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

4_ overview

Battery

Batteries(battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like.

CAUTION

Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.

These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.

The CVBS out terminal of the product is provided for easier installation, and is not recommended for monitoring purposes.

Please use the input power with just one camera and other devices must not be connected.

The ITE is to be connected only to PoE networks without routing to the outside plant.

● OVERVIEW

English _5

overview

Please read the following recommend safety precautions carefully.

yDo not place this apparatus on an uneven surface. yDo not place this apparatus near conductive material. yDo not attempt to service this apparatus yourself. yDo not install near any magnetic sources. yDo not block any ventilation openings. yDo not place heavy items on the product. yDo not expose the camera to radioactivity.

User’s Manual is a guidance book for how to use the products. The meaning of the symbols are shown below.

yReference : In case of providing information for helping of product’s usages yNotice : If there’s any possibility to occur any damages for the goods and

human caused by not following the instruction



Please read this manual for the safety before using of goods and keep it in

the safe place.

6_ overview

CONTENTS

OVERVIEW

INSTALLATION &

CONNECTION

NETWORK CONNECTION

AND SETUP

3 Important Safety Instructions 9 Product Features 10 Recomended PC Specifications 10 Recomended SD/SDHC Memory

Card Specifications

11 What’s Included 13 At a Glance (SNP-6201) 16 At a Glance (SNP-6201H)

21 Connecting with other Device 24 Installation 35 Inserting/Removing a SD Memory

Card

36 Memory Card Information (Not

Included)

37 Connecting the Camera Directly

to Local Area Networking

38 Connecting the Camera Directly

to a DHCP Based DSL/Cable Modem

39 Connecting the Camera Directly

to a PPPoE Modem

40 Connecting the Camera to a

Broadband Router with the PPPoE/Cable Modem

41 Buttons used in IP Installer 42 Static IP Setup 46 Dynamic IP Setup 47 Port Range Forward (Port

Mapping) Setup

49 Connecting to the Camera from a

Shared Local PC

49 Connecting to the Camera from a

Remote PC via the Internet

● OVERVIEW

English _7

overview

WEB VIEWER

SETUP SCREEN

APPENDIX

114

50 Connecting to the Camera 51 Login 52 Installing ActiveX 53 Installing Silverlight Runtime 55 Using the Live Screen 59 Playing the recorded video

64 Setup 64 Audio & Video Setup 85 Network Setup 94 Event Setup 108 System Setup

114 DIP Switch Setting 124 Camera Wiring 125 Specification 130 Product Overview 132 Troubleshooting 134 Open source license notification

on the product

8_ overview

PRODUCT FEATURES

• Full HD Video Quality

• Multi-Streaming

This network camera can display videos in different resolutions and qualities simultaneously using different CODECs.

• Web Browser-based Monitoring

Using the Internet web browser to display the image in a local network environment.

• Alarm

If an event occurs, the event-related video will be transferred to the FTP/email specified by the user or saved to the SD memory, or the event signal will be sent to the Alarm Out port.

• Tampering Detection

Detects tempering attempts on video monitoring.

• Motion Detection

Detects motion from the camera’s video input.

• Intelligent Video Analysis

Analyzes video to detect logical events of specified conditions from the camera’s video input.

• Face Detection

Detects faces from the camera’s video input.

• Audio Detection

Detects sound louder than a certain level specified by user.

• Auto Detection of Disconnected Network

Detects network disconnection before triggering an event.

• ONVIF Compliance

This product supports ONVIF Profile-S. For more information, refer to www.onvif.org.

● OVERVIEW

English _9

overview

RECOMENDED PC SPECIFICATIONS

• CPU : Intel Core 2 Duo 2.6GHz or higher

• Resolution : 1280X1024 pixels or higher

• RAM : 2GB or higher

• Supported OS : Windows XP / VISTA / 7, MAC OS X 10.7

• Supported Browser : Microsoft Internet Explorer (Ver. 10 ~ 7) Mozilla Firefox (Ver. 19 ~9) ※ Windows Only Google Chrome (Ver. 25 ~ 15) ※ Windows Only Apple Safari (Ver. 6.0.2(Mac OS X 10.8, 10.7 only), 5.1.7) ※ Mac OS X only

Neither a beta test version unlike the version released in the company website nor the developer version will

be supported. It is recommended to connect to IPv6 in Windows 7.

For Mac OS X, only the Safari browser is supported.

• Video Memory : 256MB or higher

If the driver of the video graphic adapter is not installed properly or is not the latest version, the

video may not be played properly.

For a multi-monitoring system involving at least 2 monitors, the playback performance can be

deteriorated depending on the system.

It is advisable to use Intel Core 2 Duo 2.93GHz or higher in a multi-browser environment.

RECOMENDED SD/SDHC MEMORY CARD SPECIFICATIONS

• 4GB ~ 32GB

• For your camera, we recommend you use a memory card from the following manufacturers: SD/SDHC Memory Card : Sandisk, Transcend

• It is recommended to use memory cards of at least class 6 speed.

10_ overview

WHAT’S INCLUDED

Please check if your camera and accessories are all included in the product package.

Appearance Item Name

Camera 1

Instruction book, Installer S/W CD,

CMS S/W DVD

Quantity

Description Model Name

● OVERVIEW

Quick Guide

(Optional)

Warranty card

(Optional)

Cable for the testing

monitor

Used to test the camera

connection to a portable display

device

SNP-6201 or

SNP-6201H

English _11

overview

Appearance Item Name

Installation base 1

Tapping Screw 4

Template 1 Product installation guide

Insulation Sheet 1

Hexagon screw 3

L Wrench 1

Installation base 1 Bracket for mounting outdoors

Quantity

Description Model Name

If installing it indoors or in a

ceiling housing

Used for installation on the

ceiling

Use when installing the camera

at highly humid place

Used for attaching the

installation base to the camera

Used for fixing the installation

base after attaching it to the

camera

SNP-6201

SNP-6201H

12_ overview

AT A GLANCE (SNP-6201)

Appearance

Item Description

Main unit

Dome Cover Dome cover for the lens and unit protection.

SD Memory Card

Compartment

After Service Port

(A/S port)

Reset Button

Protects the internal PTZ mechanism from the direct sunlight or external impact.

Compartment for the SD memory card.

This is for the repair purpose only that is not available for the user.

Pressing and holding this button for about 5 seconds will reset all camera settings to the factory default.

● OVERVIEW

c d

English _13

overview

Bottom View of Installation Base

Item Description

Safety Cable

Connection Ring

Alarm I/O Port Used to connect the alarm I/O cable.

Video Out Port Analog video output port. (for installation)

Audio Input Port Used to connect the audio input cable.

Audio Output Port Used to connect the audio output cable.

Connect the cable to prevent the product from dropping during installation to the ring.

Inner View of Installation Base

b c e

AUDIO OUT

AUDIO IN

GND

1.COM

1.NO 1.NCIN1 IN2 GND IN3 IN4

2.COM

2.NO

2.NC

i j

AC- FG AC-

IN5 IN6 GNDIN7 IN8

14_ overview

Item Description

Power Port Used to connect the power.

Communications

Ports

ID Setup Switch Specify the camera ID.

Communications

Setup Switch

Network

Connections

Used for RS-485/422 communications.

Set the transfer rate and protocols.

You can use a PoE+ or an Ethernet cable to connect this terminal to the network.

● OVERVIEW

English _15

overview

AT A GLANCE (SNP-6201H)

Appearance

Item Description

Main unit

Dome Cover Dome cover for the lens and unit protection.

Safety Cable The cable prevents the product from dropping during installation.

Protects the internal PTZ mechanism from the direct sunlight, rain or external impact.

16_ overview

Inside

Item Description

SD Memory Card Compartment

Reset Button

After Service Port (A/S port)

Compartment for the SD memory card.

Pressing and holding this button for about 5 seconds will reset all camera settings to the factory default.

This is for the repair purpose only that is not available for the user.

● OVERVIEW

English _17

overview

Bottom View of Installation Base

Item Description

Safety Cable

Connection Ring

Alarm I/O Port Used to connect the alarm I/O cable.

Video Out Port Analog video output port. (for installation)

Audio Input Port Used to connect the audio input cable.

Audio Output Port Used to connect the audio output cable.

Connect the cable to prevent the product from dropping during installation to the ring.

Inner View of Installation Base

b c e

AUDIO OUT

AUDIO IN

GND

1.COM

1.NO 1.NCIN1 IN2 GND IN3 IN4

2.COM

2.NO

2.NC

i j

AC- FG AC-

IN5 IN6 GNDIN7 IN8

18_ overview

Item Description

Power Port Used to connect the power.

Communications

Ports

ID Setup Switch Specify the camera ID.

Communications

Setup Switch

Network

Connections

Used for RS-485/422 communications.

Set the transfer rate and protocols.

You can use a PoE+ or an Ethernet cable to connect this terminal to the network.

● OVERVIEW

English _19

installation & connection

`Camera Wiring Interface Board

For the camera wiring, please refer to the picture below.

Audio

Alarm

Alarm output

Alarm Input

Video

Output

GND

1.COM

1.NO 1.NCIN1 IN2 GND IN3 IN4

2.COM

2.NO

2.NC

Audio

OUT

Power Supply

AC- FG AC-

AUDIO OUT

AUDIO IN

IN5 IN6 GND IN7 IN8

AC24V 2.5A

Power Input Ground

Select Normal Open in the setup menu.

The sensor input is activated during a short for contact type, or when it is at “Low” level for

the active type.

Select Normal Close from the Setup menu.

The sensor input is activated when open for the contact type or when in high impedance

state (open collector) for the active type.

The maximum power capacity of the alarm outputs is DC +40V and 80 mA.

When connecting alarm input and output cables, be sure to connect one cable to each

terminal respectively.

To connect products over the camera’s capacity, please use an additional relay device.

Connecting the power connector and GND incorrectly to the alarm out port may lead to fire

and damage the camera.

20_ installation & connection

ETHERNET

Communications

D+ D- TX+ TX- GND

Refer to Control Signal

Connection Diagram

CONNECTING WITH OTHER DEVICE

Preparing Adapter and Cable

Connect the camera to the power adaptor. Then, plug the power cord of the adaptor to the wall

outlet.

GND

1.COM

1.NO 1.NCIN1 IN2 GND IN3 IN4

2.COM

2.NO

2.NC

AUDIO IN

AUDIO OUT

AC- FG AC-

IN5 IN6GND IN7 IN8

Check out the rated voltage and current before making connections.

Rated Power Allowable Input Voltage Current Consumption

AC 24V AC 22V ~ 26V 2.5 A

If applied with both PoE+ and AC 24V power supplies, the device is powered from the first

engaged supply.

It is preferred to use single power supply of either one of PoE+ and AC 24V.

If connected to a switch device that provides PoE+ power, you don’t need to apply a power source

of AC 24V supply. Make sure the PoE device suffices PoE+ (IEEE 802.3at) specifications.

If your device is connected to the switch with the standard of PoE (IEEE 802.3af), then go to

the switch setup menu to “deactivate PoE”. For further information on switch device, refer to the manufacturer’s manual.

If you use a PoE+ as a power, the boot time may vary depending on a switch model (by channel)

or a maker (as PoE+ connection time is included.).

● INSTALLATION & CONNECTION

English _21

installation & connection

Electrical Resistance of Copper Wire at [20°C (68°F)]

Copper Wire Gauge (AWG) #24(0.22mm2) #22(0.33mm2) #20(0.52mm2) #18(0.83mm2)

Resistance (Ω/m) 0.078 0.050 0.030 0.018

Drop Voltage (V/m) 0.028 0.018 0.011 0.006

Recommended Distance (m) Less than 20 Less than 30 Less than 30 Less than 30

As shown in the table above, you may encounter a voltage-sag depending on the wire length.

If you use an excessively long wire for camera connection, the camera may not work properly.

Camera Operating Voltage: AC 24V±10%

Voltage drop measurements on the chart above may vary depending on the type and manufacture of

the copper cable.

Ethernet Connection

Connect the Ethernet cable to the local network or to the Internet.

22_ installation & connection

Connecting the installation monitor

Connect the cable to the camera’s rear video output terminal and the installation monitor’s video input terminal.

IN5 IN6 GNDIN7 IN8

AC- FG AC-

AUDIO OUT

AUDIO IN

GND

1.COM

1.NO 1.NCIN1 IN2 GND IN3 IN4

2.COM

2.NO

2.NC

The wiring varies depending on your monitor type and peripheral devices; please refer to the user manual

for each device. Please make sure the monitor and camera are turned off when connecting them.

This product is a network camera that transfers video over a network; the video output terminal is

used to set the imaging range of the camera at installation.

Using the terminal for monitoring purposes may cause problems such as degradation in video

quality.

It is not suitable for 24-hour monitoring using professional CRT monitors or TFT/LCD portable

monitors.

Use the network transfer screen for 24-hour monitoring and storage.

Monitor

● INSTALLATION & CONNECTION

English _23

installation & connection

INSTALLATION

Preparing & Installing Camera Bracket

For installation guidelines for brackets and housings, refer to the installation manual that is enclosed with the bracket or housing.

`Available Bracket Models

Model Item SNP-6201 SNP-6201H

SHP-3701H Outdoor Housing

-SHP-3701F Ceiling-mount Housing

SBP-300HM3 Hanging Mount

SBP-300WM1

SBP-300WM

SBP-300CM Ceiling Mount

SBP-300LM Parapet Mount

SBP-300KM Corner Mount

SBP-300PM Pole Mount

See “Optional Accessories for Installation” for the appearance of each bracket (unbundled).

(page 31)

Wall Mount

Yes

24_ installation & connection

Installing by surface attachment

SNP-6201H cannot be installed on the surface of a wall or ceiling.

`Attaching Template & Installing installation base

1. Attach the provided template on the ceiling. Based on the template, drill a 86mm

hole in the ceiling and arrange the wires through the hole.

2. Install installation base as shown.

3. Before installing the exposed bracket, open the hinged door at the bottom of the

bracket as shown in the picture. Hold the knob on the hinged door to open it.

In the case of installing the camera at highly humid place, install it on the ceiling after attaching

the enclosed insulation sheet on the back of install base.

Template

● INSTALLATION & CONNECTION

Insulation Sheet

English _25

installation & connection

`Connect Terminal Wires

1. Connect the cables to the terminal block on the hinged door. Refer to “Camera Wiring Interface Board”. (page 20)

2. Once the wiring is complete, close the hinged

door.

Do not connect the camera to a power outlet until the

installation is complete. Supplying power while the installation is in progress may cause fire or damage the product.

`Connecting Camera Safety Cable and Attaching Camera

1. First, as shown in the left hand picture, pull out the safety cable from the base and

then hook it to the mount. The safety cable is coiled inside the base.

To attach the camera to the mount, refer to the alignment guide marks as shown in the picture.

2. Carefully attach the camera to the mount following the alignment guide marks as shown in the picture.

Direction Guides

Make sure to hook the camera’s safety cable to the mount before proceeding. Otherwise you may

be exposed to serious injury caused by the camera falling.

26_ installation & connection

Align the Direction Guides

- To attach or detach the camera, refer to the picture.

• Attaching the Camera : Push up the camera unit and rotate it clockwise until it cannot be rotated anymore, as shown in the figure. After rotation, fasten the screws assembled to the install base.

< To Attach the Camera >

• Detaching the Camera : Unfasten the screws as shown in the figure, push in the hook, and rotate it counterclockwise. (The screws are not completely disassembled.) When the hook does not rotate any more, pull down the camera unit and separate it.

< To Detach the Camera >

● INSTALLATION & CONNECTION

English _27

installation & connection

Installing by wall mount

`Fix the installation base with the bracket

1. Fix the base with the bracket by turning it

clockwise.

2. As shown in the picture below, gently press and lift

up the handle of the hinged door on the bottom of the installation base. Please refer to the “Camera Wiring Interface Board” on page 20, connect the wires.

Do not connect the camera to a power outlet until the

installation is complete. Supplying power while the installation is in progress may cause fire or damage the product.

3. Connect the camera safety wire to the installation base.

Safety Cable

28_ installation & connection

4. Assemble Camera and Installation Base

Assemble the installation base and camera by matching the installation direction guides.

5. Attach Camera

Rotate the mounted camera unit clockwise so that the reference indicators of top and bottom are as shown in the image on the right.

6. Secure Camera and Installation Base

As shown in the picture below, secure the installation base and camera using 3 hexagon screws.

● INSTALLATION & CONNECTION

English _29

installation & connection

Notes for Waterproofing

This product is an indoor unit. If it is installed outdoors, use the outdoor housing to make it waterproof.

`Installing the unit on the wall by combining the outdoor housing and wall

mount

1. Install the wall mount on the vertical wall.

If the mount is installed on an inclined wall, moisture can penetrate inside the outdoor housing through the external cable.

2. Wrap the screw part of the housing with

a sufficient amount of Teflon tape for assembly.

3. When separating the dome cover and

fastening it to the housing frame, make sure that the gasket is not loosened to separate from the dome cover.

4. Install the wall mount adapter for

waterproofing, and apply the silicon sealant between and around the wall and wall mount for sealing.

Take particular caution to ensure that there

is proper sealing if the installed side is not flat.

Silicon

sealant

Wall mount

Screw

unit

Concrete wall

Teflon tape

Dome gasket

30_ installation & connection

+ 120 hidden pages