Samsung SCX-4521F Alignment & Adjustment

Page 1
Samsung Electronics
Service Manual
Alignment and Adjustments
4-1
4
4
4. Alignment and Adjustments
4.1 User Mode
Paper Type
Plain Paper, Thick, Thin, Plain Paper Bond, Color Paper, Card stock, Labels, Transparency, Envelope, Preprinted
Paper Size A4, Legal, Executive, Folio By Country
A5, B5, A6, Letter Machine ID Fax: (Only SCX-4521F) ID: Date & Time 00-00-0000 (only SCX-4521F) 00:00(AM) Clock Mode 12, 24 hours 12hours (only SCX-4521F) Language [English/FRANCAIS/Espanol/ English
Portugues/Deutsch/Italiano/
Pycckn/Norsk/Polski/
Suomi/Magyar/Dansk/
cestina/Svenska/Turkse
- 15 language
Power Save On 5, 10, 15, 30, 45 min. 5
Off Ignore Toner On
Off USB Mode Fast/Slow Fast
1. Paper Setting
Paper Type
2.Machine Setup
Machine ID
1
2
1
2
3
4
5
6
7
1st level 2nd level 3rd level Default Value
RETURN -- RETURN
left/right && Enter -- 14 character left/right && Enter
Page 2
Alignment and Adjustments
Samsung Electronics
Service Manual
4-2
Default-Change Darkness Light/Normal/Dark Normal
Original Type Text, Text/Photo, Photo Text Reduce/Enlarge [Original(100%)] 100%
[LGL
LTR(78%)]
[LGL
A4(83%)]
[A4
A5](71%)]
[A4
LTR(94%)]
[EXE
LTR(104%)]
[A5
A4](141%)] 25% 50% 150% 200% 400% [Custom:25-400]
No. of Copies [1-99] 1 Timeout 15,30,60,180Sec, Off 60sec Favorite copy Clone
Copy Collate
Autofit
2 side in 1 Pg
2 UP
4 UP
Poster Off Clone Copy Collate Autofit ID Card Copy 2 UP This will set to 2UP 4 UP This will set to 4UP Poster
3.Copy Setup
Default-Change
4. Copy Feature
Off
1
2 3
1 2 3 4 5 6 7 8
1st level 2nd level 3rd level Default Value
RETURN -- RETURN
left/right && Enter -- 14 character left/right && Enter
Page 3
Samsung Electronics
Service Manual
Alignment and Adjustments
4-3
Default-Change Resolution Standard/Fine/Super Standard
Fine/Photo/Color Ring to Answer 1~7 2 Darkness Light/Normal/Dark Normal Redial Term 1~15Min 3minutes Redials 1~13times 7times MSG Confirm On, Off, On-Error On-Error Image TCR On, Off Auto Report On, Off On Auto Reduction On, Off On Discard Size 0~30mm 20mm Receive Code 0~9 9 DRPD Mode set Receive Mode Fax, Tel, Ans/Fax, DRPD Delay Fax Fax: Priority Fax Fax: Add Page Yes, No Cancel Job Yes, No Send Forward On,Off Off RCV Forward On Start Time/ End Time
Print Local Copy
Off Off
Junk Fax Setup On Fax:
Off Off Secure Receive On,Off, Print Off Prefix Dial FAX: xxxxx (5 digits) Stamp RCV Name On, Off Off ECM Mode On, Off On Phone Book (only SCX-4521F) Sent Report (only SCX-4521F) RCV Report (only SCX-4521F) System Data Scheduled Jobs (only SCX-4521F) MSG Confirm (only SCX-4521F) Junk Fax List (only SCX-4521F) 10 ea Speaker On, Off, Comm. Comm. Ringer Off, Low,Med,High Med Key Sound On, Off Off Alarm Sound On, Off On
5. Fax Setup
(only SCX-4521F)
Default-Change
6. Fax Feature
(only SCX-4521F)
Delay Fax
7. Advanced fax
(only SCX-4521F)
8. Reports
Phone Book
9. Sound/Volume
Speaker
1
2 3 4 5 6 7 8
9 10 11 12 13
1
2
3
4
1
2
3
4
5
6
7
1
2
3
4
5
6
7
1
2
3
4
1st level 2nd level 3rd level Default Value
RETURN -- RETURN
left/right && Enter -- 14 character left/right && Enter
<continue..>
Page 4
Alignment and Adjustments
Samsung Electronics
Service Manual
4-4
Clean Drum On,Off Off Notify Toner On,Off Off Clear Memory Clear All Mem.
Paper setting Machine Setup Copy Setup Fax Setup Fax Feature Advanced Fax Sound/Volume Sent Report RCV Report
Phone Book Remote Test On Off (only SCX-4521F) Off
10. Maintenance
Clean Drum
1 2 3
4
1st level 2nd level 3rd level Default Value
RETURN -- RETURN
left/right && Enter -- 14 character left/right && Enter
<continue..>
Page 5
Samsung Electronics
Service Manual
Alignment and Adjustments
4-5
4.2 Tech Mode and Setting
4.2.1 How to Enter Tech Mode
In service (tech) mode the technician can check the machine and perform various tests to help with failure diagnosis.
When in Tech mode the machine still performs all normal operations.
To enter the Tech mode (SCX-4521F)
To enter the Tech mode press in sequence and the LCD briefly displays ‘TECH’, the machine has entered service (tech) mode.
To enter the Tech mode (SCX-4321)
To enter the Tech mode press in sequence and the LCD briefly displays ‘TECH’, the machine has entered service (tech) mode.
Page 6
Alignment and Adjustments
Samsung Electronics
Service Manual
4-6
4.2.2 Setting-up System in Tech Mode
Data Setup Send Level -9~-15 -12
(only SCX-4521F)
Modem Speed 33.6, 28.8, 14.4, 12.0, 9.6, 4.8 33.6
(only SCX-4521F)
Error Rate (only SCX-4521F) 5%, 10% 10%
Dial Mode (only SCX-4521F) Tone, Pulse Tone
Notify Toner Customer No.
Customer Name Service No.
Serial No. Clear All Mem. Clear Count Total Page Count Enter Password
CRU Print CNT
FLT Scan Count
ADF Scan Count
Used Toner CNT
Edit Toner Dot Flash Upgrade Local
Remote Silence Time Off/ 12 Sec/Unlimited Off (only SCX-4521F)
Machine Test Switch Test
Modem Test (only SCX-4521F) Dram Test Rom Test Pattern Test Shading Test
Report Protocol(only SCX-4521F)
System Data
Key History Error Info New Cartridge
Tech Mode
Data Setup
1
2
3
1st level 2nd level 3rd level Default Value
RETURN -- RETURN
left/right && Enter -- 14 character left/right && Enter
Page 7
Samsung Electronics
Service Manual
Alignment and Adjustments
4-7
4.2.3 Setting
4.2.3.1 Changing the Display Language
To change the language that displays on the control panel, follow these steps:
1. Press Menu until “Machine Setup” appears on the top line of the display.
2. Press the scroll button ( or ) until “Language” appears on the bottom line of the display.
3. Press Enter. The current setting appears on the bottom line of the display.
4. Press the scroll button ( or ) until the language you want appears on the display.
5. Press Enter to save the selection.
6. To return to Standby mode, press Stop/Clear.
4.2.3.2 Setting the Machine ID (Only for SCX-4521F)
In some countries, you are required by law to indicate your fax number on any fax you send. The Machine ID, containing your telephone number and name (or company name), will be printed at the top of each page sent from your machine.
1. Press Menu until “Machine Setup” appears on the top line of the display. The first available menu item, “Machine ID,” displays on the bottom line.
2. Press Enter. The display asks you to enter the fax number. If there is a number already set, the number appears.
3. Enter your fax number using the number keypad.
4. Press Enter when the number on the display is correct. The display asks you to enter an ID.
5. Enter your name or the company name using the number keypad. You can enter alphanumeric characters using the number keypad, and include special symbols by pressing the 0 button. For details on how to use the number keypad to enter alphanumeric characters. If you want to enter the same letter or number in succession, enter one digit, move the cursor by pressing the button and enter the next digit. If you want to insert a space in the name, you can also use the button to move the cursor to skip the position.
6. Press Enter when the name on the display is correct.
7. To return to Standby mode, press Stop/Clear.
NOTE: If you make a mistake while entering numbers, press the button to delete the last digit.
Page 8
Alignment and Adjustments
Samsung Electronics
Service Manual
4-8
4.2.3.3 Setting the Date and Time
When you turn your machine on for the first time, the display prompts you to enter the current date and time. After entering, it will not appear anymore. For the SCX-4521F, all of your faxes will have the date and time printed on them.
1. Press Menu until “Machine Setup” appears on the top line of the display.
2. Press the scroll button ( or ) to display “Date & Time” on the bottom line and press Enter.
3. Enter the correct time and date using the number keypad. For the SCX-4321, press the scroll button ( or ) to enter the time and date.
Month = 01 ~ 12 Day = 01 ~ 31 Year = requires four digits Hour = 01 ~ 12 (12-hour mode) 00 ~ 23 (24-hour mode) Minute = 00 ~ 59
You can also use the scroll button ( or ) to move the cursor under the digit you want to correct and enter a new number. For the SCX-4321, you can use Enter or Upper Level to move the cursor.
4. To sel ect “ AM” or “PM” for 12-hour format, press the or # button or any number button. For the SCX-4321, press Enter and then the scroll button ( or ). When the cursor is not under the AM or PM indicator, pressing the or # button immediately moves the cursor to the indicator. For the SCX-4321, press the scroll button ( or ) to move the cursor to the indicator. You can change the clock mode to 24-hour format (e.g. 01:00 PM as 13:00).
5. Press Enter when the time and date on the display is correct. When you enter a wrong number, the machine beeps and does not proceed to the next step. If this happens, just reenter the correct number.
6. To return to Standby mode, press Stop/Clear.
4.2.3.4 Changing the Clock Mode
You can set your machine to display the current time using either a 12-hour or 24-hour format.
1. Press Menu until “Machine Setup” appears on the top line of the display.
2. Press the scroll button ( or ) until you see “Clock Mode” on the bottom line and press Enter. The clock mode currently set for the machine displays.
3. Press the scroll button ( or ) to select the other mode and then press Enter to save the selection.
4. To return to Standby mode, press Stop/Clear.
NOTE: If power to the machine is cut off, you need to reset the correct time and date once the power has been
restored.
NOTE: The date format may differ from country to country.
Page 9
Samsung Electronics
Service Manual
Alignment and Adjustments
4-9
4.2.3.5 Setting the Paper Size and Type
After loading paper in the tray, you need to set the paper size and type using the control panel buttons. These settings will apply to copy and fax modes. For PC-printing, you need to select the paper size and type in the application program you use on your PC.
1. Press Menu. The display shows “Paper Setting” on the top line of the display.
2. Press the scroll button ( or ) to display “Paper Size” on the bottom line and press Enter to access the menu item.
3. Use the scroll button ( or ) to find the paper size you are using and press Enter to save it.
4. Press the button to scroll to “Paper Type” and press Enter to access the menu item.
5. Use the scroll button ( or ) to find the paper type you are using and press Enter to save it.
6. To return to Standby mode, press Stop/Clear.
4.2.3.6 Setting Sounds (Only for SCX-4521F)
You can control the following sounds:
• Speaker: You can turn on or off the sounds from the telephone line through the speaker, such as the dial
tone or a fax tone. With this option set to “Comm.” the speaker is on until the remote machine answers.
• Ringer: You can adjust the ringer volume.
• Key Sound: With this option set to “On” a key tone sounds each time a key is pressed.
• Alarm Sound: You can turn the alarm sound on or off. With this option set to “On” an alarm tone sounds
when an error occurs or fax communication ends.
• You can adjust the volume level using the On Hook Dial button.
4.2.3.7 Speaker, Ringer, Key Sound, and Alarm Sound
1. Press Menu until “Sound/Volume” appears on the top line of the display.
2. Press the scroll button ( or ) to scroll through the options. Press Enter when you see the desired sound option.
3. Press the scroll button ( or ) to display the desired status or volume for the option you have selected. You will see the selection on the bottom line of the display. For the ringer volume, you can select “Off,” “Low,” “Med,” and “High”. Setting “Off” means that the ringer does not sound. The machine works normally even if the ringer is turned off.
4. Press Enter to save the selection. The next sound option appears.
5. If necessary, repeat steps 2 through 4.
6. To return to Standby mode, press Stop/Clear.
Page 10
Alignment and Adjustments
Samsung Electronics
Service Manual
4-10
4.2.3.8 Speaker Volume
1. Press On Hook Dial. A dial tone sounds from the speaker.
2. Press the scroll button ( or ) until you hear the volume you want. The display shows the current volume level.
3. Press On Hook Dial to save the change and return to Standby mode.
4.2.3.9 Toner Save Mode
Toner Save mode allows your machine to use less toner on each page. Activating this mode extends the life of the toner cartridge beyond what one would experience in the normal mode, but it reduces print quality.
To turn the toner save mode on or off, press Toner Save.
• If the button backlight is on, the mode is active and the machine uses less toner when printing a document.
• If the button backlight is off, the mode is deactivated and the machine prints with the normal quantity of toner.
4.2.3.10 Power Save Mode
Power Save mode allows your machine to reduce power consumption when it is not in actual use. You can turn this mode on and select a length of time for which the machine waits after a job is printed before it switches to a reduced power state.
1. Press Menu until “Machine Setup” appears on top line of the display.
2. Press the scroll button ( or ) until “Power Save” appears on the bottom line. Press Enter.
3. Press the scroll button ( or ) to display “On” on the bottom line and press Enter. Selecting “Off” means that the power save mode is deactivated.
4. Press the scroll button ( or ) until the time setting you want appears. The available options are 5, 10, 15, 30, and 45 (minutes).
5. Press Enter to save the selection.
6. To return to Standby mode, press Stop/Clear.
NOTE: You can adjust the speaker volume only when the telephone line is connected.
Page 11
Samsung Electronics
Service Manual
Alignment and Adjustments
4-11
4.2.4 FLASH UPGRADE
There are 2 methods to update the Flash Rom, Local and Remote.
(1) Local Machine
• RCP (Remote Control Panel) mode This method is for Parallel Port or USB Port. Connect the PC and activate the RCP (Remote Control Panel) to upgrade the Firmware.
< Method > How to Update Firmware using RCP
1. Connect PC and Printer with a Parallel Cable or a USB Cable.
2. Run the RCP utility and select Firmware Update.
3. Search for the Firmware file to be used to update the set using the Browse Icon.
4. Click the Update icon. The firmware file is transmitted to the Printer automatically and the printer is initialized when the download completes.
5. Click the Refresh icon and check that the updated version numbers are displayed.
• DOS Command mode This method is ONLY for Parallel Port. Connect the PC to the set using a Parallel Cable and enter the DOS Command to upgrade the firmware.
< Method >
1. First of all you need the following files : down.bat, down_com.bin, fprt.exe, and Rom File: (file name for upgrade). Ensure you save ALL of these files in the same folder.
2. At the DOS prompt enter the correct command (as shown below) and push the enter key. Then the upgrade will automatically take place..
3. There are two commands use the correct one depending on the condition of the set..
* When the product is in the idle condition
down "rom file"
* When the product is in Ready condition
(TECH MODE --> DATA SETUP --> FLASH UPGRADE --> LOCAL)
copy/b "rom file" lpt1
4. Do not turn off the power during the upgrade process.
(2) Remote FAX
It is possible to use a set that already has the latest firmware to upgrade a remote set remotely using the telephone system.
< Method >
1. On the set that has the latest firmware set it toi transmit the upgrade:­(TECH MODE •DATA SETUP•••• FLASH UPGRADE•••• REMOTE)
2. Enter the telephone number of the set that needs to be upgraded. (Several faxes can be upgrade at the same time. In this case, enter each fax number.)
3. When the enter button is pressed the set sends the firmware file by calling designated fax number. (Around 10~15 minutes are needed to send the file.)
< Caution >
1. The Sending and Receiving fax machines MUST be the same model.
2. The sending fax must be set up in ECM mode and the Receiving fax memory must be 100%. If not the function will not work.
Page 12
Alignment and Adjustments
Samsung Electronics
Service Manual
4-12
4.2.5 Machine Test
SWITCH TEST
Use this feature to test all keys on the operation control panel. The result is displayed on the LCD window each time you press a key.
MODEM TEST
Use this feature to hear various transmission signals to the telephone line from the modem and to check the modem, amplifier and speaker. If no transmission signal sound is heard, it means the modem part of the main board, amplifier, speaker or speaker harness is faulty.
DRAM TEST
Use this feature to test the machine's DRAM. The result appears in the LCD display. If all memory is working normally, the LCD shows << O K >>
ROM TEST
Use this feature to test the machine's ROM. The result and the software version appear in the LCD display.
• FLASH VER : 1.00 V
• ENGINE VER :1.00V
PATTERN TEST
Using this pattern printout you can check that the printer mechanism is functioning properly. This function is for factory manufacturing use only.
SHADING TEST
The function is used to set the optimum scan quality determined by the specific characteristics of the CIS(Contact Image Sensor). If copy image quality is poor perform this function to check the condition of the CIS unit.
< Method >
1. Select the [Shading Test] in TECH MODE (Menu, #, 1934).
2. Push the ENTER button and an image will be scanned.
3. After scanning the CIS SHADING PROFILE will be print out.
4. If the printed image is different to the sample image shown the CIS is defective.
NOTICE : When you test the CIS, make
sure that the cover is closed.
MAX=229 Min=168 Avg=193 Diff=15 PRNU=6
MAX=234 Min=174 Avg=200 Diff=14 PRNU=7
MAX=241 Min=179 Avg=204 Diff=14 PRNU=4
MAX=240 Min=176 Avg=202 Diff=15 PRNU=6
Page 13
Samsung Electronics
Service Manual
Alignment and Adjustments
4-13
4.2.6 Report
PROTOCOL LIST
This list shows the sequence of the CCITT group 3 T.30 protocol during the most recent sending or receiving operation. Use this list to check for send and receive errors. If
SYSTEM DATA
This list provides a list of the user system data settings and tech mode settings.
KEY HISTORY
This list shows th input key history.
ERROR INFO
This list display the detail machine error list.
Page 14
Alignment and Adjustments
Samsung Electronics
Service Manual
4-14
4.3 Control Panel
4.3.1 Control Panel Functions (SCX-4521F)
SCX-4521F
Page 15
Samsung Electronics
Service Manual
Alignment and Adjustments
4-15
Page 16
Alignment and Adjustments
Samsung Electronics
Service Manual
4-16
4.3.2 Control Panel Functions (SCX-4321)
SCX-4321
Page 17
Samsung Electronics
Service Manual
Alignment and Adjustments
4-17
4.4 LCD Status Error Massages
STATUS LCD Display Descriptions
Document Jam Document Jam When Document Jam occurred at ADF module.
This is displayed on LCD, Print in the Transmission Journal.
Door Open or Jam [Front or Rear] When machine’ front side cover or Jam Cover was opened, it Cover Open [Cover Open] displayed On the LCD.
NO paper [ No Paper ] When there is no paper in CASSETTE Tray, machine Displays
Add Paper this message on LCD.
PAPER JAM 0 [Paper Jam 0] When the machine encountered paper jam in pick up area,
Open/Close Door Machine displays on the LCD until DOOR OPEN & CLOSE.
PAPER JAM 1 [Paper Jam 1] When the machine encountered paper jam in paper exit of Machine,
Open/Close Door machine displays on the LCD until DOOR OPEN & CLOSE.
PAPER JAM 2 [Paper Jam 2] When the machine encountered paper jam in paper exit of Machine,
Check Inside machine displays on the LCD until DOOR OPEN & CLOSE.
Communication Error [COMM. Error] When the machine has problem in communication, It displayed on
the LCD. Machine displays this in case of Transmission.
Machine displays this in case of fax handshaking step of Reception. Line Error [Line Error] When the machine has problem in case of Fax Data reception step. NO ANSWER [No Answer] When the machine could not connect to remote fax after Completion
of redial up to redial counter in system data. INCOMPATIBLE [Incompatible] Remote party did not have the requested feature, such as polling. LINE BUSY Line Busy The remote fax didn’t answer. POWER FAILURE Power Failure When the machine’s user memory has not been backup and There
was power off / on . STOP PRESSED [Stop Pressed] When the operator pressed the STOP button during transmission. MEMORY FULL Memory Full When the machine has encountered the user memory was full, FUSER ERROR CRU Fuse Error When the machine failed in installing the new toner cartridge. LSU ERROR [Hsync Error] tech mode LSU ERROR [LSU Error] user mode
When the machine has encountered the Laser Beam Scanning unit
could not reach the READY state, TONER LOW [Toner Low] When the machine has encountered the Toner Low, TONER EMPTY [Toner Empty] When the machine has encountered the Toner Empty,
Page 18
Alignment and Adjustments
Samsung Electronics
Service Manual
4-18
STATUS LCD Display Descriptions
BY PASS JAM [Bypass Jam] When the machine detected the non feeding from BYPASS Tray. GROUP is not available Group Not Available You have tried to select a group location where only a single
Location number can be used.
RETRY REDIAL? Retry Redial ? the machine is waiting for the programmed interval to automatically
redial a previously busy station. NO. NOT ASSIGNED NO. Not Assigned The speed dial location you tried to use has no number assigned to it. Load document Load Document You have attempted to set up a sending operation with no
Document loaded. Memory full and canel the job Cancel ? When the machine has encountered the memory full during storing
1:Yes 2:No the document into memory, the machine display the "CANCEL ?" to
operator whether he/she make a decision the canceling the job or
accept the scanned page so far to transmit the remained
documents. Job has not been created Operation Not When operator is doing in ADD/CANCEL operation and
Assigned There is no job to handle if operator entered the job no. Low Heat Error [Low Heat Error] Temperature could not reach certain level. Open Fuser Error Open Fuser Error The thermister has been disconnected. Over Heat Error [Over Heat] Temperature has gone up very high degree.
[Jam 1] When the machine detected the toner cartridge has not
[No Catridge] been installed, or detected jam1 in warmup state. Memory Dial Full Memory Dial Full During Auto dial transmission when all 15 jobs are configured and
try to add 16th job
<continue..>
Page 19
Samsung Electronics
Service Manual
Alignment and Adjustments
4-19
4.5 Engine Test Mode
The Engine Test Mode supplies useful functions to check the condition of the print engine. It tests the condition of each device and displays the result of the test on the LCD. It is divided into 5 functions (0~4), and these are shown below.
4.5.1 To enter the Engine Test Mode
To enter the Engine Test mode (SCX-4521F)
Press in sequence, and the LCD briefly displays ‘Engine Test’, the machine has entered Engine Test Mode.
Press “0”, “1”, “2”, “3” or “4” to select the Test No. (see list below – left hand column)
To enter the Engine Test mode (SCX-4321)
Press in sequence, and the LCD briefly displays ‘Engine Test’, the machine has entered Engine Test Mode.
Press “0”, “1”, “2”, “3” or “4” to select the Test No. (see list below – left hand column)
4.5.2 Diagnostic
NO. Sub No. Engine test Remark
0 1 Motor Test 1 : On, 2 : Off – next test selected
2 Pick Up Test 1 : On, 2 : Off – next test selected 3 Fan Test 1 : On, 2 : Off – next test selected 4 Manual Clt Test 1 : On, 2 : Off – next test selected 5 PTL Test 1 : On, 2 : Off – next test selected
1 1 LSU Motor Test 1 : On, 2 : Off – next test selected
2 LSU Hsync Test 1 : On, 2 : Off – next test selected 3 LD Test 1 : On, 2 : Off – next test selected
2 1 Feed Sensor Test 1. Check : read the sensor
2. Next : Next Sensor test
2 Exit Sensor Test 1. Check : read the sensor
2. Next : Next Sensor test
3 Cover Sensor Test 1. Check : read the sensor
2. Next : Next Sensor test
4 Empty Sensor Test 1. Check : read the sensor
2. Next : Next Sensor test
5 Manual Sensor Text 1. Check : read the sensor
2. Next : Next Sensor test
3 1 Therm ADC 180 1 : On, 2 : Off (maintain the fusing temp. 80˚C)
2 Therm ADC 140 1 : On, 2 : Off (maintain the fusing temp. 135˚C) 3 Therm ADC 120 1 : On, 2 : Off (maintain the fusing temp. 160˚C) 4 Therm ADC 100 1 : On, 2 : Off (maintain the fusing temp. 191˚C)
4 1 MHV Test 1 : On, 2 : Off (-1550V ±50V)
2 Dev Bias Test 1 : On, 2 : Off (-430V ± 20V) 3 THV EN/NEG Test 1 : On, 2 : Off (-1200V +300V/-150V) 4 THV ON (1300V) 1 : On, 2 : Off (+1300V ±20V) 5 THV ADC 1300V 1 : On, 2 : Off (ADC Value : 101 ±5) 6 THV ADC 600V~3500V 1 : On, 2 : Off (Compare each ADC Value)
Page 20
Alignment and Adjustments
Samsung Electronics
Service Manual
4-20
4.5.3 Detail Description (Engine T est Mode)
Function Name Description Display
01.Motor Test The main motor starts when the execution key is pressed Main Motor On/Off and stops when the stop key is pressed.
02.Pick Up Test Automatically stops, when the execution is chosen. Tray 1,2 Solenoid On/Off stops, when the execution is chosen.
03.Fan Test The fan starts when the execution key is pressed and Fan On/Off stops when the stop key is pressed.
04.Manual Clutch Test The tray2,3 clutch is on for 1sec and then it automatically Tray 2,3 Clutch On/Off stops, when the execution is chosen.On this function, the main motor runs before 2sec from the point of the clutch on in order to check the clutch state.
05.PTL Test PTL(Pre-Transfer Lamp) is lights when the execution key PTL On/Off chosen and it stops when the stop key is chosen.
11.LSU Motor The laser motor starts when the execution key is pressed Laser Motor On/Off and stops when the stop key is pressed.
12.LSU Hsync Test The LSU motor starts and "Laser Ready" is displayed if Laser Leady On/Off the motor spins at the correct speed, otherwise "Laser Error" is displayed.
13.LD Test "Diode On" is displayed, when the laser diode is on. Diode On/Off Otherwise "Diode Off" is displayed.
21.Feed Sen Test These functions allow the current state of the sensor to be
"Sensor Off" or “ Sensor On ”
22.Exit Sen Test displayed.
23.Cover Sen Test This function allows the current state of the Cover sensor
"Cover Open" or "Cover Close" to be displayed. Touch the sensor and confirm that the message changes: "Cover Open" to " Cover Close"
24.Empty Sen Test These functions allow the current state of the sensor to be
"Sensor Off" or “ Sensor On ”
25.Manual Sen Test displayed.
31.Them ADC 180 "Current value" is displayed on the upper line of the LCD, Target temperature and
32.Them ADC 140 and "Target value" on the bottom line. output temperature from
33.Them ADC 120 Target value is limited from "191°C" to "80°C" thermistor and ADC.
34.Them ADC 100
41.MHV Test These Functions are provided to check whether the MHV On/Off
42.Dev Bias Test control of the HVPS is functioning correctly. Dev Bias On/Off
43.THV EN/NEG Test THV EN/NEG On/Off
44.THV ON(1300V) THV On/Off
45.THV ADC 1300V ADC value displayed.
46.THV ADC 600V~3500 ADC value displayed.
Page 21
Samsung Electronics
Service Manual
Alignment and Adjustments
4-21
4.6 Paper Path and Clearing Paper Jams
4.6.1 Copy & Scan Document Path
Page 22
Alignment and Adjustments
Samsung Electronics
Service Manual
4-22
4.6.2 Printer Paper Path
1) After receiving a print command, the printer feeds paper from the main cassette or manual feeder as required.
2) The paper being fed passes the paper feed sensor. (Jam 0 occurs if the sensor is not operated within a certain time)
3) Having passed the paper feed sensor the paper moves to the paper exit sensor via printing process. (Jam 1 occurs if the sensor is not operated within a certain time)
4) The paper then passes through the paper exit sensor and out of the set. (Jam 2 occurs if the trailing edge of the paper does not pass the exit sensor within a certain time of the paper leading edge activating the exit sensor)
Page 23
Samsung Electronics
Service Manual
Alignment and Adjustments
4-23
4.6.3.1 In the Tray
1. Remove the jammed paper in the tray by gently pulling it straight out.
2. Open and close the front door to resume printing.
4.6.3 Clearing Paper Jams
When a paper jam occurs, “Paper Jam” appears on the display. Refer to the table below to locate and clear the paper jam.
To avoid tearing the paper, pull out the jammed paper gently and slowly. Follow the instructions in the following sections to clear the jam.
Message Location of Jam
[Paper Jam 0] In the tray Open/Close Door [Paper Jam 1] In the fuser area or around the toner Open/Close Door cartridge. [Paper Jam 2] In the paper exit area Check Inside
Page 24
Alignment and Adjustments
Samsung Electronics
Service Manual
4-24
1. Open the front door and pull the toner cartridge out, lightly pushing it down.
2. Remove the jammed paper by gently pulling it straight out.
3. Replace the toner cartridge and close the front door. Printing automatically resumes.
4.6.3.2 In the Fuser Area or Around the T oner Cartridge
NOTE: The fuser area is hot. Take care when
removing paper from the machine.
Page 25
Samsung Electronics
Service Manual
Alignment and Adjustments
4-25
1. Open and close the front door. The jammed paper automatically exits the machine. If the paper does not exit, continue to step 2.
2. Gently pull the paper out of the output tray.
3. If there is any resistance and the paper does not move when you pull, or if you cannot see the paper in the output tray, open the rear door by pulling the tab on it.
4. Remove the jammed paper by gently pulling it straight out.
5. Close the rear door.
6. Open and close the front door to resume printing.
4.6.3.3 In the Paper Exit Area
NOTE: Inside of the machine is hot. Take care
when removing paper from the machine.
Page 26
Alignment and Adjustments
Samsung Electronics
Service Manual
4-26
1. Load the paper into the tray, as shown below.
2. Open the printer’s properties window, set the paper size to A5 from the Paper tab.
3. From the Orientation option of the Layout tab, set the Rotate option to 90 .
4. Click OK to start printing. For details, see Software User’s Guide.
4.6.3.4 Tips for Avoiding Paper Jams When Printing on the A5-sized Paper
If paper jams occur frequently when you print on A5-sized paper:
4.6.3.5 Tips for Avoiding Paper Jams
By selecting the correct paper types, most paper jams can be avoided. When a paper jam occurs.
• Follow the procedures in “Loading Paper”. Ensure that the adjustable guides are positioned correctly.
• Do not overload the tray.
• Do not remove paper from the tray while your machine is printing.
• Flex, fan, and straighten the paper before loading.
• Do not use creased, damp, or highly curled paper.
• Do not mix paper types in the tray.
• Use only recommended print materials. See “Paper Specifications”.
• Ensure that the recommended print side of print materials is facing up in the tray.
Loading...