Samsung NV51K6650SS, NV51K6650DS Installation

Built-In Electric Wall Oven

Installation manual

NV51K7770** / NV51K6650** / NV51*5*****

Install_NW9000K_DG68-00862A-09_EN.indd 1 2019-11-11  5:36:05

ContentsContents

Safety informations

Safety informations 2

Contents

Related equipment safety 2
Transport 2

Preparation 4

Checklist 4
Prepare to install the oven 4
Location requirements 5
Product dimensions - single ovens (NV51K7770S, NV51K6650S) 5
Product dimensions - single oven (NV51*5***S*) 6
Cabinet dimensions - single ovens 6
Product dimensions - double ovens (NV51K7770D, NV51K6650D) 7
Product dimensions - double oven (NV51*5***D*) 8
Cabinet dimensions - double ovens 8

Installation instructions 10

Prepare built-in oven 10
Remove and replace oven door(s) 11
Electrical connection 13
Install oven 15

Self-diagnosis 16

Temp sensor & Heater check 16

Related equipment safety

Remove all tape and packaging before using the appliance. Dispose of the
packaging after unpacking the appliance. Never allow children to play with
packaging material.

Never modify or alter the construction of the appliance. For example, do not
remove panels, wire covers or screws.

Transport

To avoid damage to the oven vent, use the transport method shown in the picture
below.

Support the bottom of the oven from either
side when moving it into the installation

A

B

A. Front
B. Pallet

DANGER

ELECTRICAL SHOCK HAZARD

To avoid risk of electrical shock, personal injury or death; verify your appliance
has been properly grounded in accordance with local codes or in absence of codes,
with the National Electrical Code (NEC). ANSI/NFPA 70-latest edition.

WARNING

MOVING HAZARD

To avoid risk of severe personal injury; this appliance requires two or more people
while handling and moving. Use of appliance moving devices is recommended.

location. Leave the unit attached to the
shipping pallet until it is in front of the
cabinet opening and is ready to be lifted
into place.

2 English

Install_NW9000K_DG68-00862A-09_EN.indd 2 2019-11-11  5:36:05

WARNING

• The information in this manual should be followed exactly.

• A re or electrical shock may result causing property damage, personal

injury or death.

• Important - Save this installation manual for local electrical inspector's use.

• Proper Installation - Be sure your appliance is properly installed and grounded

by a qualied technician.

• New branch-circuit installations (1996 NEC), mobile homes, recreational
vehicles, or installations where local codes prohibit grounding through the
neutral conductor require 4-wire branch-circuit connection.

• Improper connection of aluminum house wiring to copper leads can result in
an electrical hazard or re. Use only connectors designed for joining copper to
aluminum and follow the manufacturer’s recommended procedure closely.

• Mounting screws must be used.

• Failure to do so can result in the oven falling out of the cabinet causing

serious injury.

CAUTION

• Make sure the cabinets and wall coverings around the oven can withstand the
temperature (up to 194 °F [90 °C]) generated by the oven.

• Discoloration, delamination or melting may occur.

• DO NOT remove spacers on the side walls of the built-in oven.

• These spacers center the oven in the space provided. The oven must be

centered to prevent excess heat buildup that may result in heat damage
or re.

WARNING

• The information in this manual should be followed exactly.

• A re or electrical shock may result causing property damage, personal

injury or death.

IMPORTANT NOTE

Proper installation is the responsibility of the installer and product failure due to
improper installation is NOT covered under warranty.

WARNING

• DO NOT put any weight on the oven door. Never allow anyone to climb, sit,
stand or hang on the oven door.

• The oven could tip and injury might result from food or the oven itself.

WARNING

• The electrical power must be shut off while the electrical connections are
being made.

• Failure to do so can result in severe personal injury, death or electrical

shock.

IMPORTANT NOTE

• Observe all governing codes and ordinances. This appliance must be properly
grounded.

• Keep oven vent ducts unobstructed. The oven vent is located bottom of the
oven. This area could become hot during oven use. Never block this vent or
place plastic or heat-sensitive items in front of it.

Safety informations

English 3

Install_NW9000K_DG68-00862A-09_EN.indd 3 2019-11-11  5:36:05

Preparation

Preparation

Checklist

Use this checklist to verify that you have completed each step of the installation
process. This can help you avoid mistakes.

1. Before installing the oven, be sure to verify the cabinet dimensions are correct
for your unit and the required electrical connections are present.

2. Refer to the installation manual for content regarding Safety, Cabinet
Dimensions, Removing Packaging, Electrical Installation, Testing the
Installation and Customer Service.

3. To lift up the oven, hang the install handle onto the side hook of the unit.

4. Move the oven unit into place in front of the cabinet opening, leaving the

bottom packaging on the unit to avoid damaging ooring.

5. Team lift the unit directly into the cabinet cutout taking care not to pinch
ngers or scratch hands or arms. Make sure the electrical conduit reaches to
the connection point properly.

6. Slide the unit all the way into place, making sure to route the electrical conduit
correctly.

7. Fasten the oven unit to the cabinetry opening with screws supplied (using
Phillips screwdriver).

8. Consult the complete installation instructions and follow the remainder of the
procedures listed, including performing an operation test.

9. All product literature and accessories are supplied (may be wrapped or boxed)
with the oven.

10. INSTALLER - Leave the literature pack and the accessories with the customer.

11. Hang the install handle onto the side hook of the oven.

Prepare to install the oven

Phillips Screwdriver Drill

Prepare to install the oven

6 screws (M4 L16)

6 Wood Screws For

Mounting (4 needed for

installation and 2 extra’s)

Materials needed

30” (76.2 cm)

Metal Bottom Trim

Install Handle

(only for double oven)

Junction Box Wire Nuts

4 English

Install_NW9000K_DG68-00862A-09_EN.indd 4 2019-11-11  5:36:06

3

/4” Conduit Connector

Location requirements

IMPORTANT: Observe all governing codes and ordinances.

• Cabinet opening dimensions that are shown must be used.

Given dimensions provide minimum clearance with oven.

• Recessed installation area must provide complete enclosure around the

recessed portion of the oven.

• Grounded electrical supply is required. See “Electrical Requirements”

section.

• Electrical supply junction box should be located 3” (7.6 cm) maximum below
the support surface when the oven is installed in a wall cabinet. A 1” (2.5 cm)
minimum diameter hole should have been drilled in the right rear or left
rear corner of the support surface to pass the appliance cable through to the
junction box.

NOTE

For under counter installation, it is recommended that the junction box be located
in the adjacent right or left cabinet. If you are installing the junction box on rear
wall behind oven, it is recommended that the junction box be recessed and located
in the upper Right of the cabinet.

• Oven support surface must be solid, level and ush with bottom of cabinet
cutout.

• Floor must be able to support a single oven weight of 199 lb (90 Kg).

• Floor must be able to support a double oven weight of 331 lb (150 Kg).

IMPORTANT: To avoid damage to your cabinets, check with your builder or
cabinet supplier to make sure that the materials used will not discolor, delaminate
or sustain other damage. This oven has been designed in accordance with the
requirements of UL and CSA International and complies with the maximum
allowable wood cabinet temperatures of 194 °F (90 °C).

Product dimensions - single ovens (NV51K7770S, NV51K6650S)

B

F

H

A

13

A 28

B 28

C 27

D 26

D-1 23

D-2 24

E 29

F 47

/16” (73.1 cm) Overall height

1

/2” (72.4 cm) Recessed width

3

/16” (69.1 cm) Recessed height

15

/16” (68.5 cm) Overall depth (with Handle)

1

/8” (58.7 cm) Recessed depth

3

/8” (62.0 cm) Overall depth

3

/4” (75.6 cm) Door width

1

/4” (120 cm) Conduit length

G 30” (76.0 cm) Overall width (Handle width)

9

H 2

/16” (6.5 cm) Handle depth

G

C

E

D-1

D-2

D

DIMENSION

Preparation

English 5

Install_NW9000K_DG68-00862A-09_EN.indd 5 2019-11-11  5:36:06

Preparation

J

Preparation

Product dimensions - single oven (NV51*5***S*)

B

H

A

G

A 28

B 28

C 27

D 26

D-1 23

D-2 24

E 29

F 47

G 28

H 2

E

DIMENSION

13

/16” (73.1 cm) Overall height

1

/2” (72.4 cm) Recessed width

3

/16” (69.1 cm) Recessed height

5

/8” (67.6 cm) Overall depth (with Handle)

1

/8” (58.7 cm) Recessed depth

3

/8” (62.0 cm) Overall depth

3

/4” (75.6 cm) Overall width (Door width)

1

/4” (120 cm) Conduit length

9

/16” (72.5 cm) Handle width

1

/4” (5.7 cm) Handle depth

D-1

D-2

D

Cabinet dimensions - single ovens

Single Oven Under counter

01 Gas or Electric cooktops may be installed over this oven. See cooktop

F

C

installation instructions for cutout size. See label on top of approved
cooktop models.

02 Gas and Electrical Connections for Gas Cooktop Must be Located in an

Adjacent Accessible Location to the Right.

01

K

B

F

A

D

E

G

A

02

I

H

C

DIMENSION

A Min.
B Min. 4
C 3
D Min. 28
E Min. 1”/ Max. 1
F Min. 27
G Min. 23

11

/16” (1.75 cm) – Overlap of Over Side Edges of Cutout

1

/8” (10.5 cm)

5

/8” (9.1 cm)

1

/2”/ Max. 285/8” (Min. 72.4 cm / Max. 72.7 cm)

1

/4” (Min. 2.5 cm / Max. 3.2 cm)

1

/4”/ Max. 273/8” (Min. 69.2 cm / Max. 69.5 cm)

1

/2” (Min. 59.7 cm)

H Min 22” (Min 55.9 cm)

I Max. 9

J 36

1

/2” (Max. 24.1 cm) – Junction Box

3

/8” (92.3 cm) - Counter top Height

K 25” (63.5 cm)

6 English

Install_NW9000K_DG68-00862A-09_EN.indd 6 2019-11-11  5:36:06

Single Oven Wall Mount

01 Junction Box
02 Allow a minimum of 22” for clearance to adjacent corners, drawers, walls,

etc. when door is open

A

B

01

I

Product dimensions - double ovens (NV51K7770D, NV51K6650D)

B

F

H

G

F

J

02

D

E

22”

H

G

C

DIMENSION

A 30” (76.2 cm)
B Min. 1

3

/8” (3.5 cm)

C Min. 31” (Min 78.7 cm)
D Min. 28
E Min. 1”/ Max. 1
F Min. 27
G Min. 23

1

/2”/ Max. 285/8” (Min. 72.4 cm / Max. 72.7 cm)

1

/4” (Min. 2.5 cm / Max. 3.2 cm)

1

/4”/ Max. 273/8” (Min. 69.2 / Max. 69.5 cm)

1

/2” (Min. 59.7 cm)

H Min. 22” (Min. 55.9 cm)

I Max. 9

J Min.

1

/2” (Max. 24.1 cm) – Junction Box

11

/16" (1.75 cm) - Wooden cabinet thickness

A

C

G

E

D-1

D-2
D

DIMENSION

A 51
B 28

C 49

D 26
D-1 23
D-2 24

E 29

1

/2” (130.7 cm) Overall height

1

/2” (72.4 cm) Recessed width

7

/8” (126.7 cm) Recessed height

15

/16” (68.5 cm) Overall depth (with Handle)

1

/8” (58.7 cm) Recessed depth

3

/8” (62.0 cm) Overall depth

3

/4” (75.6 cm) Door width

F 67” (170 cm) Conduit length
G 30” (76.0 cm) Overall width (Handle width)
H 2

9

/16” (6.5 cm) Handle depth

Preparation

English 7

Install_NW9000K_DG68-00862A-09_EN.indd 7 2019-11-11  5:36:06

Preparation

Preparation

Product dimensions - double oven (NV51*5***D*)

B

H

G

A

G

E

D

DIMENSION

A 51
B 28

C 49

D 26
D-1 23

D-2 24

E 29

1

/2” (130.7 cm) Overall height

1

/2” (72.4 cm) Recessed width

7

/8” (126.7 cm) Recessed height

5

/8” (67.6 cm) Overall depth (with Handle)

1

/8” (58.7 cm) Recessed depth

3

/8” (62.0 cm) Overall depth

3

/4” (75.6 cm) Overall width (Door width)

F 67” (170 cm) Conduit length

G

H

9

28

/16” (72.5 cm)

1

/4” (5.7 cm)

2

F

C

D-1

D-2

Handle width

Handle depth

Cabinet dimensions - double ovens

Double Ovens Installed in Cabinet

01 Junction Box
02 Allow a minimum of 22” for clearance to adjacent corners, drawers, walls,

etc. when door is open

A

01

B

F

D

E

02

DIMENSION

A 30” (76.2 cm)
B Min. 1
C 12” (30.5 cm)
D Min. 28
E Min. 1”/ Max. 1

1

/2”/ Max. 285/8” (Min. 72.4 cm / Max. 72.7 cm)

1

F 50
G Min. 23
H Min 47” (Min. 119.4 cm)

I Max. 9

J Min.

1

/2” (Max. 24.1 cm) – Junction Box

11

/16" (1.75 cm) - Wooden cabinet thickness

I

J

H

22”

G

C

3

/16” (3.0 cm)

/4” (Min. 2.5 cm / Max. 3.2 cm)

1

/4” (127.6 cm)

1

/2” (Min. 59.7 cm)

8 English

Install_NW9000K_DG68-00862A-09_EN.indd 8 2019-11-11  5:36:07

If codes permit and a separate ground wire is used, it is recommended that a
qualied electrical installer determine that the ground path and the wire gauge are
in accordance with local codes.
Check with a qualied electrical installer if you are not sure the oven is properly
grounded.
This oven must be connected to a grounded-metal permanent wiring system.
Be sure that the electrical connection and wire size are adequate and in
conformance with the National Electrical Code, ANSI/NFPA 70-latest edition or CSA
Standards C22.
1-94, Canadian Electrical Code, Part 1 and C22.2 No. O-M91-latest edition, and all
local codes and ordinances.

A copy of the above code standards can be obtained from:

Electrical Connection

To properly install your oven, you must determine the type of electrical connection
you will be using and follow the instructions provided in this manual.

• Oven must be connected to the proper electrical voltage and frequency as
specied on the model/serial/rating plate. The model/serial/rating plate is
located on the bottom left side of the trim. See the following illustrations.

National Fire Protection Association
1 Batterymarch Park
Quincy, MA 02169-7471

CSA International
8501 East Pleasant Valley Road
Cleveland, OH 44131-5575

A

A

Single Oven

A. Model/serial/rating plate

Double Oven

A. Model/serial/rating plate

• A circuit breaker is recommended.

• Use the chart below to determine the minimum recommended dedicated

circuit protection.

KW Rating (240 V) KW Rating (208 V)

Recommended Circuit

Size (Dedicated)

≤4.8 KW ≤4.1 KW 20 Amp

4.9 KW - 7.5 KW 4.3 KW - 6.2 KW 30 Amp

7.3 KW - 9.6 KW 6.3 KW - 8.3 KW 40 Amp

9.7 KW - 12.0 KW 8.4 KW - 10.4 KW 50 Amp

• Connect directly to the circuit breaker box (or fused disconnect) through
exible, armored or nonmetallic sheathed, copper cable (with grounding wire).
See “Electrical Connection” section.

English 9

Preparation

Install_NW9000K_DG68-00862A-09_EN.indd 9 2019-11-11  5:36:07

Installation instructions

Preparation

Installation instructions

Installation instructions

• Flexible conduit from the oven should be connected directly to the junction
box.

• Fuse both sides of the line.

• Do not cut the conduit. The length of conduit provided is for serviceability of

the oven.

• A UL listed or CSA approved conduit connector must be provided.

• If the house has aluminum wiring, follow the procedure below:

1. Connect a section of solid copper wire to the ends of the exible conduit

leads.

2. Connect the aluminum wiring to the added section of copper wire using

special connectors and/or tools designed and UL listed for joining copper

to aluminum.
Follow the electrical connector manufacturer's recommended procedure.
Aluminum/copper connection must conform with local codes and industry
accepted wiring practices.

For power requirements for models NV51K6650D, NV51K6650S, NV51K7770D,
NV51K7770S, NV51*5***D, and NV51*5***S, refer to the following table.

Model

NV51K6650D 9.3 7.0

NV51K6650S 4.9 3.7

NV51K7770D 10.6 8.0

NV51K7770S 6.2 4.7

NV51*5***D 8.9 6.7

NV51*5***S 4.9 3.7

240 VAC 208 VAC

kW kW

Prepare built-in oven

WARNING

Excessive Weight Hazard

Use two or more people to move and install an oven.
Failure to do so can result in back or other injury.

1. Decide on the nal location for the oven. Avoid drilling or cutting into house
wiring during installation.

2. To avoid oor damage, set the oven on a cardboard prior to installation. Do
not use handle or any portion of the front frame for lifting.

3. Remove the shipping materials and tape from the oven.
Remember to keep the packing materials that may be needed for installation.

4. Remove the hardware package from inside of the bag containing literature.

5. Remove racks and other parts from inside the oven.

6. Move oven and cardboard close to the oven’s nal location.

10 English

Install_NW9000K_DG68-00862A-09_EN.indd 10 2019-11-11  5:36:07

Remove and replace oven door(s)

A

B

IMPORTANT: Use two hands to remove oven door. For double ovens, repeat the
process for each door.
Prior to removing the oven door, prepare a surface where you will place it. This
surface should be at and covered with a soft blanket, or use the corner posts
from your packaging material.

Disconnect LED light wire harness (Only NV51K7770** / NV51K6650**)

Locate the LED light wire harness and disconnect it before removing the door.

Wire Harness

Single Oven Double Oven

1. Carefully pull the wire to reveal the

connector.

2. Disconnect the connector.

Remove oven door(s)

A. Oven door hinge lock in

locked position

B. Oven door hinge lock in

unlocked position

1. Open the oven door.

2. Locate the oven door hinge locks in

both corners of the oven door, and
then rotate the hinge locks toward the
oven door to the unlocked position (see
illustration B). If the door hinge lock
is not rotated fully, the door will not
remove properly.

3. Partially close the door to engage the
door latch locks.
The door will stop at this point.

Installation instructions

4. Using two hands, grasp the edges of

the oven door. Lift and pull the oven
door toward you and remove. You may
need to gently shift door from side to
side as you pull.

5. Set the oven door(s) aside on the
prepared covered work surface with the
oven door resting on its handle.

6. To continue with the oven installation,
go to the “Positioning Oven Feet
for Multiple Cabinet Cutout Heights”
section.

Install_NW9000K_DG68-00862A-09_EN.indd 11 2019-11-11  5:36:07

English 11

Installation instructions

A

Installation instructions

Replace oven door(s)

CAUTION

The door is very heavy. You may need help lifting the door high enough to slide it
into the hinge slots. Do not lift the door by the handle.

1. Using two hands, grasp side edges of
door at the midpoint.
Face the oven cavity.

2. Locate the slots on each side of the
oven cavity for the door hinge locks.

A. Slot in the oven cavity for

door hinge lock

3. At a 45° angle, align door hinges with
slots in the lower front of the oven
cavity. Slowly insert door, making sure
you maintain the 45° angle. You will
know the door is engaged in the slot
when you feel a slight drop.

4. Lower the oven door to the fully open
position. If the oven door does not open
to a full 90°, repeat steps 1 through 3.

5. Locate the oven door hinge locks in the
corners of the oven door, and rotate the
hinge locks toward the oven cavity to
the locked position.
See Step 1 (illustration A) in the
“Remove Oven Door(s)” section for
proper locked position.

6. Close the oven door.

7. When the hinges are properly installed

and the door closed, there should be
an even gap between the door and the
control panel. If one side of the oven
door is hanging lower than the other,
the hinge on that side is not properly
installed.

8. Connect Wire Harness.

12 English

Install_NW9000K_DG68-00862A-09_EN.indd 12 2019-11-11  5:36:07

Electrical connection

Electrical Connection Options Chart

For Double Ovens

WARNING

Electrical Shock Hazard

Disconnect power before servicing.
Use 8 gauge solid copper wire.
Make sure to ground the oven.
Failure to follow these instructions can result in death, re, or electrical shock.

This oven is manufactured with a neutral (white) power supply wire and a cabinet­connected ground (green or bare) wire twisted together.

1. Disconnect power.

A

A. UL listed or CSA approved

conduit connector

2. Feed the exible conduit from the oven
through the opening in the cabinet.

3. Remove junction box cover if it is
present.

4. Install a UL listed or CSA approved
conduit connector to the junction box.

5. Route the exible conduit from the
oven to the junction box through a
UL listed or CSA approved conduit
connector.

6. Tighten screws on conduit connector.

7. See “Electrical Connection Options

Chart” to complete installation for your
type of electrical connection.

If your home has: Go to section:

4-wire

4-Wire Cable from Home Power Supply

½”

(1.3 cm)

3-wire

3-Wire Cable from Home Power Supply

½”

(1.3 cm)

NOTE

If the power connection is plugged in improperly, "bAd LinE" appears on the
display.
Reconnect the power connection properly, and the message disappears.

Installation instructions

For Single Ovens

WARNING

Electrical Shock Hazard

Disconnect power before servicing.
Use 8 gauge solid copper wire.
Electrically ground oven.
Failure to follow these instructions can result in death, re, or electrical shock.

English 13

Install_NW9000K_DG68-00862A-09_EN.indd 13 2019-11-11  5:36:08

Installation instructions

A

E

B

G

H

I

C

D

F

A

E

B

G
H

I

C

D

F

Installation instructions

4-Wire Cable from Home Power Supply
IMPORTANT: Use the 4-wire cable from home power supply in the U.S. where local

codes do not allow grounding through neutral, New Branch circuit installations
(1996 NEC), mobile homes and recreational vehicles, new construction and in
Canada.

1. Connect the 2 black wires (B) together
using a UL listed wire connector.

2. Connect the 2 red wires (C) together
using a UL listed wire connector.

3. Untwist white wire from green (or bare)
ground wire coming from the oven.

4. Connect the 2 white wires (F) together
using a UL listed wire connector.

5. Connect the green (or bare) ground
wire (H) from the oven cable to the
green (or bare) ground wire (in the

A. Cable from home power

supply

B. Black wires (normally L1)
C. Red wires (normally L2)
D. 4-wire exible conduit from

oven

E. Junction box
F. White wires (normally

N-neutral)

G. UL listed wire connectors
H. green wires (normally

G-ground)

I. UL listed or CSA approved

conduit connector

junction box) using a UL listed wire
connector.

6. Install junction box cover.

3-Wire Cable from Home Power Supply - U.S. Only
IMPORTANT: Use the 3-wire cable from home power supply where local codes

permit a 3-wire connection.

1. Connect the 2 black wires (C) together
using a UL listed wire connector.

2. Connect the 2 white wires (D) and
the green (or bare) ground wire (of
the oven cable) using a UL listed wire
connector.

3. Connect the 2 red wires (G) together
using a UL listed wire connector.

4. Install junction box cover.

A. Cable from home power

supply

B. Junction box
C. Black wires (normally L1)
D. White wires (normally

N-neutral)

E. green wires (normally

G-ground)

F. 4-wire exible conduit from

oven

G. Red wires (normally L2)
H. UL listed wire connectors
I. UL listed or CSA approved

conduit connector

14 English

Install_NW9000K_DG68-00862A-09_EN.indd 14 2019-11-11  5:36:08

Install oven

A

B

C

A

B

C

1. Using 2 or more people, lift the oven
partially into the cabinet cutout. Hang
the install handle onto the side hook of
the oven as shown below.

NOTE

Carefully push against front oven frame.

WARNING

When inserting the oven, use caution not to
deform or damage the barrier underneath.

Barrier

Install

Handle

5. The bottom metal trim are shipped in

the foam packing.
To install the metal bottom trim, see
following instructions.

• Align tab of the bottom trim with a
hole in the left side trim of the unit

2. Push against the seal area of the front
frame to push the oven into the cabinet
until the back surface of the front frame
touches the front wall of the cabinet.

A. Trim Left
B. Trim Bottom
C. Screw

as shown. Repeat on the right side.

• Using one screw on each side
of the trim tab, fasten the trim
securely to the oven.

NOTE

Installation instructions

The bottom trim piece is to cover any
unwanted gaps.

3. Push oven completely into the cabinet
and center the oven into the cabinet
cutout.

4. Remove the tape from front trims.

• Securely fasten the oven to the

cabinet using the screws provided.

• Insert the screws through hole in

trim aligning with hole in oven
frame. Do not overtighten screws.

A. Trim Left
B. Trim Bottom Large

6. If the cutout size is larger than

inches use of the wider bottom trim is
recommended.

NOTE

To select the bottom trim properly, measure
the cutout between cabinet and oven. See
the following chart.

TYPE

Cutout 0 – 3/4”

3

/4

3

/4” – 23/4”

C. Screw

Install_NW9000K_DG68-00862A-09_EN.indd 15 2019-11-11  5:36:09

English 15

Self-diagnosis

Self-diagnosis

Temp sensor & Heater check

1. After connecting the power, check if the display works properly.

2. Remove all accessories (Gliding Rack, Flat-Rack, Smart Divider...etc.) from

inside of the oven cavity.

3. You cannot proceed with self-diagnosis if the oven cavity is hot or the door is
open.

• In this case, “Hot or door” message appears on the display.

4. To start self-diagnosis, press both Hidden Keys simultaneously for 5 seconds.

• Refer to the table below for the hidden keys for each model.

Model NV51K6650** NV51K7770**

Control panel

Keep Warm + “9” UPPER + LOWER

Hidden Key

Model NV51*5*****

Control panel

and touch "Install test" on

display.

5. If there is no error, 'PASS' appears on the display with an alert sound.

6. If there is an error, following message appears on the display with an alert

sound.

All models

Double/Single Oven

Double Oven Only

Feature

Model

Upper Broil H-2

Upper Bake H-1

Lower Broil H-4

Lower Bake H-3

Error code Remark

7. If an error occurs, contact a Samsung service center for further service.

NOTE

If you see any other error messages that are not listed above, please contact a
Samsung service center. call e.g. 1-800-SAMSUNG (726-7864)

Self-diagnosis

Install_NW9000K_DG68-00862A-09_EN.indd 16 2019-11-11  5:36:09

Hidden Key Keep Warm + “9”

16 English

Memo

Install_NW9000K_DG68-00862A-09_EN.indd 17 2019-11-11  5:36:09

Memo

Install_NW9000K_DG68-00862A-09_EN.indd 18 2019-11-11  5:36:09