Page 1
Emulation PCL5e (ML-5000A), WPS (ML-5000G)
Interface (Parallel Port) Centronics IEEE- P1284 compatible bi-directional (Nibble, Byte, ECP)
Print Speed 8 PPM (A4 Size, 5 % Character Pattern)
Print Method Non-impact Electrophotography, Laser Beam
Resolution 600 X 600 DPI
Memory Standard: 4 Mb (ML-5000A) / 1 Mb (ML-5000G)
Expandable up to 36 Mb for ML-5000A only
Operating Environment Temperature : 10 ~ 32.5
o
C,
Humidity: 20 ~ 80 % RH
Storage Environment Temperature : -20 ~ 40 oC,
Humidity: 10 ~ 95 % RH
Weight Net : 7.5 kg (max.),
Gross : 9.5 kg (max.)
Dimension 345 (W) X 364 (D) x 224 (H) mm
Certification & Compliance CE, TUV, SEMKO, NEMKO, DEMKO, C-tick
FCC, UL, CSA, CDRH, CB, EPA
2. Specifications
2-1 General
Samsung Electronics 2-1
Page 2
2-2 Samsung Electronics
Specifications
Input Voltage AC 200~240 V ± 15 %, 50/60 Hz ± 3 Hz
DC Output Voltage
Line Regulation 24 V ± 3 %
5 V ± 2 %
Load Regulation 24 V - 3 %/+10 %
5 V ± 3 %
Ripple Noise 24 V : 120 mV (Peak 400 mV)
5 V : 50 mV (Peak 100 mV)
Over Current Protect 24 V : 2.7 A ± 10 % (by C't )
5 V : 1.5 A ± 10 % (by C't )
Power Consumption Max. 450 Wh Everage: 200 Wh
Power Save Mode: 25 Wh
Warming Up Time 20 seconds or less
First Print Time Idle mode : 20 seconds or less
Power Save mode : 30 seconds or less
Acoustic Noise Standby : 36 dB or less
Sleep Mode: Background level
Operating : 48 dB or less
Reliability
Insulation Resistance 10 Mohm or less (at DC 500 V)
Dielectric Strength AC 1500 V (DC 2100 V), 10 mA
Ground Continuous 0.1 ohm or less
Voltage DIP Rated voltage ± 15 %
AC Impulse Noise AC 1000 V 10, 100, 200, 400, 1000 ns
Leakage Current 3.5 mA or less
Surge 0.5 ~ 4 kV, 0.25 ~ 2 kA
Ozone Emission 0.1 ppm or less (8 hours)
Top Cover Open Isolating the input power of the LSU, high voltage part, and fuser
Overcurrent Protect Fuse inside the Engine Controller
Fusing System
Trouble Sensing The temperature doesn't rise to the specific temperature within a
specific time. Fuser error occurs if the temperature is too high.
Overheat Sensing 240 ~ 250
o
C (The thermostat cuts off the Fuser from the power.)
Thermistor Open Sensing Without the initial temperature change of the Fuser
Source of Light Laser Diode (LSU)
Developer
Developing Non-magnetic contact developing
Charging Conductive roller charging
Density Adjustment Dark, Medium
Transfer System Pre-transfer by LED & conductive roller
Fusing System Temperature & Pressure
Ozone Emission 0.1 PPM or less (8 hours)
2-2 Electrical
Page 3
Samsung Electronics 2-3
Specifications
Conditions
Paper Normal paper (75 g/m2)
Environment Temperature : 20 ~ 25 oC, Humidity : 40 ~ 60 % RH
Print Quality
Image Density min. 1.3
Background max. 1.0
Uniformity max. 0.2 (including continuous print)
Fusing min. 80 % (all black)
Start Position Top : x ± 3 mm, Side : y ± 3 mm (from left)
Skew Top : max. ± 1.5 mm/200 mm
Side : max. ± 1.5 mm/250 mm
Orthogonality ± 1.0 mm
Horizontal Scan ± 0.6 mm/208 mm
(Bowed Line Skew : S600,0909 pattern)
Special Paper Exception Image Density : min. 1.0 (envelope)
Fusing : min. 70 % (all black, envelope/OHP/postcard)
Paper Jam 1/2,000 or less
Paper Curl First : 16 mm or less (10 sheets)
After Cooling: 12 mm or less (10 sheets)
2-3 Print Quality
Toner Cartridge
Type One-cartridge type
Life Span Built-in toner cartridge : 5,000 pages at 5 % coverage (ML-5000A)
3,000 pages at 5 % coverage (ML-5000G)
Optional toner cartridge: 5,000 pages at 5 % coverage
Note: Its duration may last longer under Econo mode.
Memory (ML-5000A only) Memory RAM: 2, 4, 16, 32 Mb (memory is expandable to 36 Mb)
Note: Memory option is not available for ML-5000G.
2-4 Option
Page 4
2-4 Samsung Electronics
Specifications
Input Paper Size
Paper Type Size Feeding Source
A4 210 x 297 mm Paper Tray or Manual feeder
Letter 216 x 279 mm Paper Tray or Manual feeder
B5 (ISO) 176 x 250 mm Paper Tray or Manual feeder
Executive 184 x 267 mm Paper Tray or Manual feeder
Folio 216 x 330 mm Paper Tray or Manual feeder
Legal 216 x 356 mm Paper Tray or Manual feeder
Com-10 Envelope 105 x 241 mm Manual feeder only
Monarch Envelope 98 x 191 mm Manual feeder only
DL Envelope 110 x 220 mm Manual feeder only
C5 Envelope 162 x 229 mm Manual feeder only
C6 Envelope 114 x 162 mm Manual feeder only
A5 Envelope 148 x 210 mm Manual feeder only
Transparency A4 or Letter Manual feeder only
Label paper A4 or Letter Manual feeder only
*Others Width: 75-216 mm, Length: 125-356 mm Paper Tray or Manual feeder
*ML-5000A only
Feeding Source Paper tray and manual feeder
Paper Weight 60 ~ 163 g/m
2
Input Paper Capacity Paper tray: 150 sheets, Manual feeder : 1 sheet at a time
Paper Stacker Capacity Face down : 100 sheets, Face up : 1 sheet
Paper Limitations -Adhesive label sheets specifically designed for laser printers
-Transparencies specifically designed for laser printers
-Envelopes with peel-off adhesive strips or more than one fold-over flap
to seal must have adhesive compatible with the heat and pressure of the
printerÕs fusing process.
Unacceptable Papers -Paper with embossed lettering, perforations, or rough texture
-Paper with which color was added after the paper was made
-Paper forms whose ink is not for laser printing
2-5 Paper
Loading...