Samsung DVD-R130 User Manual [bg]

Instruction Manual

DVD-R130

English

www.samsung.com/mea

AK68-01004L-00

Warning

IMPORTANT NOTE

The mains lead on this equipment is supplied with a moulded plug incorporating a fuse. The value of the fuse is indicated on the pin face of the plug. If it requires replacing, a fuse approved to BS1362 of the same rating must be used.

Getting Started

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER(OR BACK). NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Do not install this equipment in a confined space such as a bookcase or similar unit.

WARNING : To prevent damage which may result in

CAUTION : DVD RECORDER USES AN INVISIBLE

CAUTION

THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.

This symbol indicates “dangerous voltage” inside the product that presents a risk of electric shock or personal injury.

This symbol indicates important instructions accompanying the product.

fire or electric shock hazard, do not expose this appliance to rain or moisture.

LASER BEAM WHICH CAN CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE RECORDER CORRECTLY AS INSTRUCTED.

Never use the plug with the fuse cover omitted if the cover is detachable. If a replacement fuse cover is required, it must be of the same colour as the pin face of the plug. Replacement covers are available from your dealer.

If the fitted plug is not suitable for the power points in your house or the cable is not long enough to reach a power point, you should obtain a suitable safety approved extension lead or consult your dealer for assistance.

However, if there is no alternative to cutting off the plug, remove the fuse and then safely dispose of the plug. Do not connect the plug to a mains jack, as there is a risk of shock hazard from the bared flexible cord.

To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the mains plug shall be readily operable.

The product unit accompanying this user manual is licensed under certain intellectual property rights of certain third parties. This license is limited to private noncommercial use by end-user consumers for licensed contents. No rights are granted for commercial use. The license does not cover any product unit other than this product unit and the license does not extend to any unlicensed product unit or process conforming to ISO/IEC 11172-3 or ISO/IEC 13818-3 used or sold in combination with this product unit. The license only covers the use of this product unit to encode and/or decode audio files conforming to the ISO/IEC 11172-3 or ISO/IEC 13818-3. No rights are granted under this license for product features or functions that do not conform to the ISO/IEC 11172-3 or ISO/IEC 13818-3.

WARNING: DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL WHICH IS MARKED WITH THE LETTER BY THE EARTH SYMBOL, OR COLOURED GREEN OR GREEN AND YELLOW.

CAUTION

Caution: To prevent electric shock, match wide blade

- English

of plug to wide slot, fully insert.

Precaution

Important Safety Instructions

Read these operating instructions carefully before using the DVD Recorder. Follow all the safety instructions listed below. Keep these operating instructions handy for future reference.

● Exterior interference such as lightning and static

electricity can affect normal operation of this DVD Recorder. If this occurs, turn the DVD Recorder off and on again with the STANDBY/ON button, or disconnect and then reconnect the AC power cord to the AC power outlet. The DVD Recorder will operate normally.

● Be sure to remove the disc and turn off the DVD

Recorder after use.

● Disconnect the AC power cord from the AC outlet

when you don’t intend to use the DVD Recorder for long periods of time.

● Clean the disc by wiping in a straight line from the

inside to the outside of the disc.

Getting Started

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings, Install in accordance with the manufacturer's instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding- type plug. A polarized plug has two blades with one wider than the other. A groundingtype plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. if the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or

pinched particularly at plugs, convenience receptacles, the point where they exit from the apparatus.

11) Only use attachments/accessories specified by the

manufacturer.

12) Use only with the cart, stand, tripod, bracket, or

table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or

when unused for long periods of time.

14) Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Maintenance of Cabinet

For safety reasons, be sure to disconnect the AC power cord from the AC outlet.

● Do not use benzene, thinner, or other solvents for

cleaning.

● Wipe the cabinet with a soft cloth.

Disc Handling

● Use discs with regular

shapes. If an irregular disc (a disc with a special shape) is used, this DVD recorder may be damaged.

Holding discs

● Avoid touching the surface of a

disc where recording is performed.

DVD-RW and DVD-R

● Clean with an optional DVD-

RAM/PD disc cleaner (LFK200DCA1 where available). Do not use cleaners or cloths for CDs to clean DVD-RW/ DVD-R discs.

DVD-Video, Audio CD

● Wipe off dirt or contamination on the disc with a soft

cloth.

Cautions on handling discs

Handling Cautions

● Before connecting other components to this DVD

Recorder, be sure to turn them all off.

● Do not move the DVD Recorder while a disc is being

played, or the disc may be scratched or broken, the DVD Recorder’s internal parts may be damaged.

● Do not put a flower vase filled with water or any small

metal objects on the DVD Recorder.

● Be careful not to put your hand into the disc tray.

● Do not place anything other than the disc in the disc

tray.

● Do not write on the printed side with a ball-point pen

or pencil.

● Do not use record cleaning sprays or antistatic.

Also, do not use volatile chemicals, such as benzene or thinner.

● Do not apply labels or stickers to discs. (Do not use

discs fixed with exposed tape adhesive or leftover peeled-off stickers.)

● Do not use scratch-proof protectors or covers.

● Do not use discs printed with label printers available

on the market.

● Do not load warped or cracked discs.

English -

Disc Storage

Be careful not to harm the disc because the data on these discs is highly vulnerable to the environment.

● Do not keep under direct sunlight.

● Keep in a cool ventilated area.

● Store vertically.

Getting Started

● Keep in a clean protection jacket.

● If you move your DVD recorder suddenly from a cold

place to a warm place, condensation may generate on the operating parts and lens and cause abnormal disc playback. If this occurs, do not connect the plug to the power outlet and wait for two hours. Then insert the disc and try to play back again.

Disc Specifications

DVD-Video

● A digital versatile disc (DVD) can contain up to

135-minutes of images, 8 audio languages and 32 subtitle languages. It is equipped with MPEG-2 picture compression and Dolby digital surrounding, allowing you to enjoy vivid and clear theatre quality images in the comfort of your own home.

● When switching from the first layer to the second

layer of a dual-layered DVD Video disc, there may be momentary distortion in the image and sound. This is not a malfunction of the DVD Recorder.

● Once a DVD-R/-RW recorded in Video Mode is

finalised, it becomes DVD-Video.

Audio CD

● An audio disc on which 44.1kHz PCM Audio is

recorded

● Plays CD-DA format audio CD-R and CD-RW discs.

The DVD Recorder may not be able to play some CD-R or CD-RW discs due to the condition of the recording.

CD-R/-RW

MP3 CD-R/-RW

● Only CD-R discs with MP3 files recorded with

ISO9660 or JOLIET format can be played back

● Only MP3 files with the ".mp3", ".MP3" extension can

be used.

● For MP3 files recorded with a VBR(Variable Bit

Rates), from 32 Kbps to 320 Kbps, the sound may cut in out.

● Playable bitrate range is from 56Kbps to 320Kbps.

● This DVD Recorder can handle a maximum of 500

files and 100 folders.

JPEG CD-R/RW

● Only JPEG files with the ".jpg", ".JPG" extension can

be used.

● This DVD Recorder can handle a maximum of 500

files and 100 folders.

● Maximum size of progressive JPEG is 3M pixels.

● MOTION JPEG is not supported.

Using CD-R/-RW

● Use a 700MB(80 minutes) CD-R/-RW disc.

If possible, do not use a 800MB(90 minutes) or above disc, as the disc may not play back.

● If the CD-R/-RW disc was not recorded as a closed

session, you may experience a delay in the early playback time, all recorded files may not play.

● Some CD-R/-RW discs may not be playable with this

DVD Recorder, depending on the device which was used to burn them. For contents recorded on CD-R/RW media from CDs for your personal use, playability may vary depending on contents and discs.

Using MPEG4 disc

● Disc : CD-R/-RW, DVD-R/-RW

● MPEG4 File with following extensions can be played.

: .avi, .divx, .AVI, .DIVX

● MPEG4 Codec format : DivX 3.11 DivX 4.x DivX 5.x

DivX-Pro Xvid

● Motion Compensation : QPEL, GMC

● four CC : MPG4, mpg4, DIV3, divX3, DIVX, divX,

DX50, MP43, mp43, XVID, xvid

● Available Audio Format : “MP3”, “MPEG1 Audio

Layer2”, “LPCM”, “AC3”, “DTS”, “MS ADPCM”

●

Supported subtitle file formats: .smi, .srt, .sub, .psb, .txt, .ass

DVD-R Disc Playback and Recording

● Once a DVD-R recorded in Video Mode is finalised, it

becomes DVD-Video.

● You can record onto the available space on the disc

and perform editing functions such as giving titles to discs and programmes and erasing programmes before finalising.

● When programming is erased from a DVD-R, that

space does not become available. Once an area on a DVD-R is recorded on, that area is no longer available for recording, whether the recording is erased or not.

● It takes about 30 seconds for the DVD Recorder to

complete recording management information after recording finishes.

● This DVD Recorder optimizes the DVD-R for each

recording. Optimizing is carried out when you start recording after inserting the disc or turning on the DVD Recorder. Recording onto the disc may become impossible if optimizing is carried out too many times.

● Playback may be impossible in some cases due to

the condition of recording.

● This DVD Recorder can play back DVD-R discs

recorded and finalised with a Samsung DVD video recorder. It may not be able to play some DVD-R discs depending on the disc and the condition of the recording.

DVD-RW Disc Playback and Recording

● Recording and playback can be performed on DVD-

RW discs in both the Video and VR Modes.

● Once a DVD-RW recorded in both the Video and VR

Modes is finalised, you cannot perform addtional recording.

● Once a DVD-RW recorded in Video Mode is finalised,

it becomes DVD-Video.

● In both modes, playback can be performed before

and after finalisation, but additional recording, deleting and editing can not be performed after finalisation.

- English

● If you want to record the disc in VR Mode and then

record in V Mode, be sure to execute Format. Be careful when executing Format because all the recorded data may be lost.

● A DVD-RW blank disc is initialized to VR Mode when

first initialized.

● DVD-RW (VR mode)

- This is a format that is used for recording data on a

DVD-RW disc. You can record multiple titles, edit, delete, partial delete, create a playlist, etc.

- A disc that is recorded in this mode may not be

played by existing DVD Recorder.

● DVD-RW (Video mode)

- This is a format that is used for recording data on a

DVD-RW or DVD-R disc. The disc can be played by existing DVD Recorder once it has been finalised.

- If a disc that has been recorded in Video Mode by a

different maker’s recorder but has not been finalised, it cannot be played or additionally be recorded by this DVD Recorder.

COPY PROTECTION

● Many DVD discs are encoded with copy protection.

Because of this, you should only connect your DVD recorder directly to your TV, not to a VCR. Connecting to a VCR results in a distorted picture from copy-protected DVD discs.

● This DVD Recorder incorporates copyright

protection technology that is protected by methods claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorised by Macrovision Corporation, is intended for home and other limited viewing uses only unless otherwise authorised by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

Do not use the following discs!

● LD, CD-G, CD-I, Video-CD, CD-ROM and DVD-ROM

discs should not be used in this DVD Recorder. [Note] Disc types that can be played : CD/CD-R/CD-RW/ MP3/JPEG/MPEG4/DVD-Video/DVD-RW/DVD-R. For a DVD-R/DVD-RW disc, which has been recorded in Video Mode on another component, it can play only when finalised.

●

Some commercial discs and DVD discs purchased outside your region may not be playable with this DVD Recorder. When these discs are played, either “No Disc” or "Please check the regional code." will be displayed.

● If your DVD-RW disc is an illegal copy or is not in

DVD video format, it may also not be playable.

Disc Compatibility

●

High Speed Recording discs can be used in this DVD Recorder.

●

Not all brands of discs will be compatible with this DVD Recorder.

Getting Started

Protection

This DVD Recorder can allow you to protect the contents of your discs, as described below.

● Programme-protected: See page 67

“Locking(Protecting) a Title”

● Disc-protected: See page 79 “Disc Protection”

DVD-RW/DVD-R discs that are incompatible with the

✻

DVD-VIDEO format cannot be played with this DVD Recorder.

✻ For more information on DVD recording compatibility,

consult your DVD-RW/DVD-R manufacturer.

✻ Use of poor quality DVD-RW/DVD-R discs may

cause following unexpected problems including, without limitation, recording failure, loss of recorded or edited materials or damage to the DVD Recorder.

English -

Contents

Getting Started

Warning........................................................................2

Precaution...................................................................3

Important Safety Instructions.............................................3

Handling Cautions..............................................................3

Maintenance of Cabinet.....................................................3

Other type of connecting the Audio output cable

Case 1 : Connecting to your TV......................................19

Case 2 : Connecting to a stereo amplifier

with AV output jacks..........................................20

Case 3: Connecting to an AV amplifier with a digital

output jack ..........................................................20

..19

Connecting to AV 2 IN, DV input jack...................21

Case 1 : Connecting a VCR, Set-Top Box(STB), DVD

player or Camcorder to the AV 2 IN jacks.......21

Case 2 : Connecting a Camcorder to the DV IN jack ...21

System Setup

Disc Handling .....................................................................3

Disc Storage .......................................................................4

Disc Specifications .............................................................4

General Features........................................................8

Before reading the user’s manual...........................9

How to use the DVD Recorder.................................9

Unpacking .................................................................11

Accessories.......................................................................11

Preparing the Remote Control.........................................11

Setting the Remote Control .............................................11

Description................................................................13

Front Panel .......................................................................13

Front Panel Display..........................................................13

Rear Panel........................................................................14

Tour of the Remote Control .............................................15

Connecting & Setting Up

Quick Overview........................................................16

Connecting the DVD Recorder .................................17

Other type of connecting the Video output cable

Case 1 : Connecting to a Video (Composite)

output jack .........................................................18

Case 2 : Connecting to an S-Video output jack.............18

Case 3 : Component Video output jacks........................19

...17

On-Screen Menu Navigation..................................22

Plug & Auto Set up..................................................23

Setting the Clock......................................................24

Presetting Channels with

the Auto Setup function..........................................24

Presetting Channels with

the Manual Setup function.....................................25

Setting up the Language Options.........................26

EP Mode Time Setting.............................................27

Automatic Chapter Creation..................................28

DivX(R) Registration................................................29

Setting up the Audio Options................................29

Audio Options...................................................................29

Setting up the Progressive scan...........................30

Canceling the Progressive scan...........................31

Setting up the Display(Video) Options.................31

Display(Video) Options ....................................................32

Setting up the Parental Control.............................32

If you forgot your password.............................................33

About the Rating Level ....................................................33

About the Change Password ..........................................34

- English

Recording

Before Recording.....................................................35

Recordable discs..............................................................35

Recording Formats ..........................................................36

Recording Mode...............................................................36

Unrecordable video..........................................................36

About INFO Button...........................................................37

Checking the available disc space (Disc Information)...37

Zooming-In........................................................................53

Using Bookmarks.............................................................54

Using Markers ..................................................................55

Playing an Audio CD/MP3 .....................................56

Playing an Audio CD (CD-DA)/MP3...............................56

Playing a Picture......................................................60

Playing a MPEG4 .....................................................61

Playing the Title List................................................62

Getting Started

Recording the current TV programme you are

watching....................................................................37

Recording from external equipment you are

watching....................................................................39

Copying from a Camcorder ...................................40

Making a One Touch Recording (OTR)................41

Making a Timer Recording.....................................42

Flexible Recording (for Timer recording only) ...43

Editing the Scheduled Record List.......................43

Deleting the Scheduled Record List.....................44

Recording the Standard Timer List ......................45

Playback

Before Playing..........................................................46

Region code (DVD-Video only).......................................46

Disc types that can be played .........................................46

Discs that cannot be played ............................................46

Playing a Disc...........................................................47

Using the Disc & Title Menu............................................48

Using the Search Functions ............................................48

Slow Motion Play..............................................................49

Editing

Basic Editing (Title List)...................................................66

Renaming(Labeling) a Title..............................................66

Locking(Protecting) a Title...............................................67

Deleting a Title .................................................................67

Deleting a Section of a Title ............................................68

Advanced Editing (Playlist) .............................................

Creating a Playlist ...........................................................70

Playing Entries in the Playlist .........................................71

Renaming a Playlist Entry ...............................................72

Editing a Scene for the Playlist .......................................73

Copying a Playlist Entry to the Playlist ...........................76

Deleting a Playlist Entry from the Playlist.......................77

Disc Manager

Editing the Disc Name .....................................................78

Disc Protection .................................................................79

Formatting a Disc.............................................................79

Delete All Title Lists ..........................................................80

Finalising a disc................................................................81

Unfinalising a disc (V/VR mode) .....................................82

..............................................................78

Step Motion Play..............................................................49

About ANYKEY ................................................................49

Using the Repeat Function..............................................50

Selecting the Subtitle .......................................................52

Selecting the Audio language..........................................52

Changing the Camera Angle...........................................53

Additional Information

Troubleshooting.......................................................83

Specifications...........................................................87

English -

General Features

High quality progressive scan

Progressive scanning provides high resolution and flicker free video. The 10-bit 54-MHz DAC and 2D Y/C Separating Circuitry provides the highest image playback and recording quality. (See pages 19, 30~31)

Getting Started

The DVD Recorder allows you to record and play high quality digital video on DVD-RW/DVD-R discs. You can record and edit digital images on DVD-RW/DVD-R discs as if they were VCR tapes.

High quality digital audio and video recording and playback

Record up to 8-hours of images with a 4.7 GB DVD-RW/DVD-R disc, depending on the recording mode.

Selectable Recording Mode

You can set your recorder to one of four different recording speeds, each varying in recording quality and length. EP(6Hr or 8Hr) mode yields the most recording time, LP & SP modes provide less recording time with higher quality recording, XP mode gives you the highest quality recording.

Automated Quality Adjustment for Timer Recording

If FR mode is selected, the video quality is adjusted automatically so that all video for the scheduled time can be recorded onto the free disc space. (See page 43.)

A variety of functions with an easy-to-use user interface

The integrated menu system and the messaging function allow you to perform desired operations both easily and conveniently. With a DVD-RW disc, you can edit recorded video, create a playlist, edit video in a specific sequence according to your requirements.

MPEG4 playback

This DVD Recorder can play MPEG4 formats within an avi file.

DivX Certification

DivX, DivX Certified, and associated logos are trademarks of DivXNetworks, Inc and are used under licence.

Creating a DVD video title using DVD-RW/DVD-R disc

With the DVD Recorder, you can create your own DVD Video titles on 4.7 GB DVD-RW/DVD-R discs.

Copying data from a digital camcorder using a DV input jack

Record DV Device video onto DVD-RW, DVD-R discs using the DV input jack (IEEE 1394-4pin/4pin). (See page 40.)

- English

Before reading the user’s

How to use the DVD

Getting Started

manual

Make sure to check the following terms before reading the user’s manual.

Icons that will be used in manual

Icon Term Definition

This involves a function available

DVD

JPEG in a data picture CD-R/-RW,

MP3

MPEG4

Caution function does not operate or

NOTE on the page that help each

One-Touch

button by using only one button.

ANYKEY A function that can be operated

button by using ANYKEY button.

About the use of this user’s manual

1) Be sure to be familiar with Safety Instructions before using this DVD Recorder. (See pages 2~5)

2) If a problem occurs, check for Troubleshooting. (See pages 83~86)

in DVD or DVD-R/DVD-RW discs that have been recorded and finalised in Video Mode.

This involves a function available

in DVD-RW.

This involves a function available

in DVD-R.

This involves a function available

in a data CD (CD-R or CD-RW).

This involves a function available

DVD-R/-RW.

This involves a function available in a data CD-R/-RW,DVD-R/-RW.

This involves a case where a

settings may be cancelled.

This involves tips or instructions

function operate.

A function that can be operated

Recorder

Step 1

This DVD Recorder can record on the following types of discs. If you want to repeatedly record on the same disc or you want to edit the disc after recording, select a rewritable DVD-RW type disc. If you want to save recording without any change, choose a non-rewritable DVD-R.

Step 2

Unlike a VCR, the DVD Recorder automatically starts formatting when an unused disc is inserted. This is required for the preparation of recording on a disc.

Using a DVD-RW

This type of disc can be formatted in either DVD-Video format (Video mode) or DVD-Video Recording format (VR mode). For an unused disc, a message that asks whether to format in VR Mode or not is displayed. You can play a Video mode disc on various DVD components. A VR mode disc allows more varied editing.

Using a DVD-R

Formatting a disc is unnecessary and only Video Mode Recording is supported. You can play this type of discs on various DVD components only when they have been finalised.

NOTE

Select the disc type

Format the disc to start recording

■

You can only use either the VR or Video mode on a DVD-RW, but not both at the same time.

■

You can change the DVD-RW format to another format by reinitializing. It should be noted that the disc's data will be lost when changing formats.

English -

Step 3

Recording

Step 6

Finalising & Playing on other DVD components

There are two different recording methods, Direct Recording and Timer Recording. Timer recording is classified as a Date : Once, Daily, MO-SA, MO-FR, W-SA, etc.

Getting Started

Recording mode : XP (high quality mode), SP (standard quality mode), LP (long recording mode), and EP (extended mode) according to the recording mode. When recording is set in the FR mode, the best quality picture is recorded with regards to the remaining time on the disc.

Step 4

You can select the title you want to play in a displayed menu and then immediately start playback. A DVD consists of sections called titles, and sub sections called chapters. During recording, a title is created between two points where you start and stop recording. Chapters will be created automatically when you finalise recording on DVD-R / DVD-RW discs in Video mode. The chapter’s length (interval between chapters) varies according to the recording mode.

Playing

To play your DVD on other DVD components, finalising may be necessary. First, finish all editing and recording operations, then finalise the disc.

When using a DVD-RW disc in VR Mode

Although finalising is generally unnecessary when playing the disc on a VR Mode compatible component, a finalised disc should be used for playback.

When using a DVD-RW disc in Video Mode

The disc should be finalised first to enable playback on anything other than this DVD Recorder. No more editing or recording can be made on the disc once it has been finalised.

When using a DVD-R disc

You should finalise the disc to play it on a component other than this DVD Recorder. You cannot edit or record on the disc once it has been finalised.

Step 5

Editing on discs is easier than conventional video tapes. The DVD Recorder supports many different edit functions, possible only with DVDs.

With a simple and easy edit menu, you can operate various edit functions, such as delete, copy, rename, lock, etc., on a recorded title.

Creating a playlist (DVD-RW in VR mode)

With this DVD Recorder, you can create a new playlist on the same disc and edit it without the change of the original recording.

- English

Editing a recorded disc

Unpacking

Getting Started

Accessories

Check for the supplied accessories below.

Video/Audio Cable

Remote Control

Instruction Manual

RF Cable for TV

Batteries for Remote

Control (AAA Size)

Quick Guide

Preparing the Remote Control

Setting the Remote Control

You can control certain functions of another manufacturer’s TV with this remote control. Control function buttons involve:

PROG TV MUTE, INPUT SEL. button.

, VOL +/-, Direct Number buttons,

STANDBY/ON,

Install Batteries in the Remote Control

● Open the battery cover on the back of the remote

control.

● Insert two AAA batteries. Make sure that the polarities

(+ and -) are aligned correctly.

● Replace the battery cover.

If the remote does not operate properly:

● Check the polarity + - of the batteries (Dry-Cell)

● Check if the batteries are drained.

● Check if remote sensor is blocked by obstacles.

● Check if there is any fluorescent lighting nearby.

Dispose of batteries according to local environmental regulations. Do not put them in the household trash.

English -

To determine whether your television is compatible, follow the instructions below.

1. Switch your television on.

2. Point the remote control towards the television.

3. Press and hold the STANDBY/ON button and enter

the two-figure code corresponding to the brand of your television, by pressing the appropriate number

Getting Started

buttons.

Controllable TV Codes

BRAND BUTTON SAMSUNG 01, 02, 03, 04, 05, 06, 07, 08, 09 AIWA 82 ANAM 10, 11, 12, 13, 14, 15, 16, 17, 18 BANG & OLUFSEN 57 BLAUPUNKT 71 BRANDT 73 BRIONVEGA 57 CGE 52 CONTINENTAL EDISON 75 DAEWOO EMERSON 64 FERGUSON 73 FINLUX 06, 49, 57 FORMENTI 57 FUJITSU 84 GRADIENTE 70 GRUNDIG 49, 52, 71 HITACHI 60, 72, 73, 75 IMPERIAL 52 JVC 61, 79 LG 06, 19, 20, 21, 22, 78 LOEWE 06, 69 LOEWE OPTA 06, 57 MAGNAVOX 40 METZ 57 MITSUBISHI 06, 48, 62, 65 MIVAR 52, 77 NEC 83 NEWSAN 68 NOBLEX 66 NOKIA 74 NORDMENDE 72, 73, 75 PANASONIC 53, 54, 74, 75 PHILIPS 06, 55, 56, 57 PHONOLA 06, 56, 57 PIONEER 58, 59, 73, 74 RADIOLA 06, 56 RADIOMARELLI 57 RCA 45, 46 REX 74 SABA 57, 72, 73, 74, 75 SALORA 74 SANYO 41, 42, 43, 44, 48 SCHNEIDER 06

BRAND BUTTON SELECO 74 SHARP 36, 37, 38, 39, 48 SIEMENS 71 SINGER 57 SINUDYNE 57 SONY 35, 48 TELEAVA 73 TELEFUNKEN 67, 73, 75, 76 THOMSON 72, 73, 75 THOMSON ASIA 80, 81 TOSHIBA 47, 48, 49, 50, 51, 52 WEGA 57 YOKO 06 ZENITH 63

Result: If your television is compatible with the remote

control, it will switch off. It is now programmed to operate with the

19, 20, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34

remote control.

■

NOTE

■

Then you can control the television using the following buttons after the TV button.

Button Function

STANDBY/ON Used to switch the television on and off.

INPUT SEL. Used to select an external source.

VOL (+ or -) Used to adjust the volume of the television.

PROG ( or ) Used to select the desired channel.

TV MUTE Used to toggle the sound on and off.

0~9 Used to input number directly.

■

NOTE

If several codes are indicated for your television brand, try each one in turn until you find one that works.

If you replace the remote control's batteries, you must set the brand code again.

The various functions will not necessarily work on all televisions. If you encounter problems, operate the television directly.

- English

Description

Front Panel

Getting Started

1. STANDBY/ON

Turns the DVD Recorder on and off.

2. AV 2 IN

Connect external equipment.

3. DV IN

Connects external digital equipment with a DV jack. (such as a camcorder)

4. DISC TRAY

Opens to accept a disc.

5. OPEN/CLOSE

Opens and closes the disc tray.

6. DISPLAY

Displays the playing status, title/chapter/time, etc.

Front Panel Display

7. SEARCH/SKIP

Go to the next title/chapter/track or go back to the previous title/chapter/track.

8. PLAY/PAUSE

Plays a disc or pauses playback/recording.

9. P.SCAN

Selects the progressive scan mode.

10.PROG ( )

Select TV preset Channels. Same as PROG button on the remote control.

11. REC

Starts recording.

12.STOP

Stops disc playback.

1. Lights when a disc is loaded.

2. Lights in the record mode.

3. Lights to indicate the timer record mode.

4. Lights when a DVD-R/-RW disc is loaded.

5. Playing time/clock/current status indicator.

6. Lights in the progressive scan mode.

English -

Rear Panel

Getting Started

1. RF IN / RF OUT

Connects antenna cables.

2. DIGITALAUDIO OUT(OPTICAL)

Connects to an amplifier having a digital optical audio input jack.

3. DIGITALAUDIO OUT(COAXIAL)

Connects to an amplifier having a digital coaxial audio input jack.

4. AUDIO OUT

Connects to the audio input of external equipment using audio cables.

5. VIDEO OUT(good video quality)

Connects the input of external equipment using a Video cable.

6. S-VIDEO OUT(better video quality)

Connects the input of external equipment using an S-Video cable.

7. COMPONENT VIDEO OUT(best video quality)

Connects to equipment having Component video input jacks.

8. AV 1 AUDIO IN

Connect the output of external equipment using audio cables

9. AV 1 VIDEO IN

Connects the output of external equipment using a video cable.

10. AV 1 S-VIDEO IN

Connects the output of external equipment using a S-Video cable.

■

The Antenna connection does not pass

NOTE

output signal of DVD. To watch a DVD on your TV, you must connect audio/video cables.

- English

Tour of the Remote Control

26 27

4 5 6 7

12 13

28 29

16 17

22 23

24 25

13. ANYKEY Button

Use this to view the status of the disc that is being played.

14. REC Button

Use to make a recording on DVD-RW/-R discs.

15. REC MODE Button

This will display the recording status.(XP/SP/LP/EP)

16. REPEAT Button

Allows you to repeat a title, chapter, track or disc.

17. OPEN/CLOSE Button

To open and close the disc tray.

18. SUBTITLE Button

Press this to switch the DVD’s subtitle language.

19. PLAY/PAUSE Button

Press to play a disc or pause playback/recording.

20. PROG Buttons

Select preset channels in a specific order. Same as PROG buttons in front panel.

21. RETURN Button

Returns to a previous menu.

22. PLAY LIST/TITLE MENU Button

Use this to return to the Title menu, or to view the recorded files list.

23. CANCEL Button

24. MARKER/TIMER Button

Use this to bookmark a position while playing a disc. Press to directly enter the Timer Recording Mode menu while stopping a disc.

25. INFO Button

This will display current settings or disc status.

26. TV Button

Press this to operate TV.

27. DVD Button

Press this when you use a DVD recorder.

28. INPUT SEL. Button

Select line input signal in external input mode (PROG, AV input or DV INPUT)

29. ZOOM Button

Press this to enlarge the screen.

Getting Started

1. STANDBY/ON Button

2. 0~9(Number) Buttons

3. TV/DVD Button

You can not use this button.

4. Reverse/Forward Skip Buttons

Press to skip a disc backwards or forwards.

5. Reverse/Forward Step Buttons

Press to play frame by frame.

6. Reverse/Forward Search Buttons

Press to search a disc backwards or forwards.

7. STOP Button

Press to stop a disc.

8. VOL Buttons

Volume adjustments.

9. AUDIO/TV MUTE Button

Use this to access various audio functions on a disc.(DVD mode) This operates as Sound Mute. (TV mode)

10. MENU Button

Brings up the DVD recorder’s setup menu.

¥ 

11. OK/DIRECTION(

) Buttons

12. TITLE LIST/DISC MENU Button

Use this to enter the View Recording list/Disc menu.

English -

Quick Overview

Connecting

& Setting Up

This section involves various methods of connecting the DVD Recorder to other external components and required initial setting modes.

Connecting & Setting Up

A Quick Overview presented in this guide will give you enough information to start using the DVD Recorder.

Connecting the DVD Recorder

†

Other type of connecting the Video output cable

†

Other type of connecting the Audio output cable

†

Connecting to AV 2 IN, DV input jack

Quick Overview.................................................16

Connecting the DVD Recorder

Other type of connecting the

Video output cable............................................17

Other type of connecting the Audio output cable

Connecting to AV 2 IN, DV input jack .............21

- English

..........................17

....19

Connecting the DVD

Other type of connecting

Recorder

1. Disconnect the aerial cable from your TV and connect it to on the rear panel of the DVD

Recorder.

2. Connect of the DVD Recorder and the aerial input of your TV using the supplied aerial cable.

3. Use the Video/Audio Cable to connect ANALOG AUDIO OUT(R/L)/VIDEO OUT jacks on the DVD Recorder to the Audio &Video jacks on the TV.

4. Plug in the DVD Recorder and TV.

5. Turn on the DVD Recorder and TV.

6. Press the INPUT SEL. button on your TV remote control until the Video signal from the DVD Recorder appears on the TV screen.

Wall

DVD Recorder

the Video output cable

There are several ways to output video signal. Select one of the following video connecting that best suits you below.

● Case 1 : Connecting to a Video (Composite) output

jack

● Case 2 : Connecting to an S-Video output jack

● Case 3 : Component Video output jacks

S-Video, Component video and Progressive Output Modes

● S-Video and Component video output are available

only if your TV supports S-Video input or Component video input, respectively. If S-Video or Component video output does not work, check the TV connections and the TV input selection settings.

● Compared to standard interlaced video, progressive

scan doubles the amount of video lines fed to your TV, resulting in a more stable, flicker-free, clear image than interlaced video. This is only available with TVs that support progressive scan.

● Progressive Scan Output (576p)

Consumers should note that not all high definition television sets are fully compatible with this DVD Recorder and may cause artifacts to be displayed in the picture, in case of 576 progressive scan picture problems, It is recommended that the user switch the connection to the ‘standard definition’ output. If there are questions regarding our TV set compatibility with this model 576p DVD Recorder, please contact our customer service centre.

Connecting & Setting Up

NOTE

■

The RF cable connection of this DVD Recorder sends only signals of TV. You must connect Audio/Video cables to watch a signal from your DVD Recorder.

■

To watch TV programmes, power off the DVD Recorder.

English -

Case 1 : Connecting to a Video (Composite) output jack

1. Connect a video(yellow) cable between the VIDEO

(yellow) OUT jack on DVD Recorder and VIDEO (yellow) INPUT jack on your TV (or AV amplifier).

● You will enjoy regular quality images.

2. Connect audio cables (white and red) between the

AUDIO OUT jacks on the DVD Recorder and AUDIO IN jacks on TV (or AV amplifier).

(See page 19 to 20)

Connecting & Setting Up

Video/Audio Cable

Case 2 : Connecting to an S-Video output jack

1. Connect an S-Video cable (not included) between the S-VIDEO OUT jack on DVD Recorder and S-VIDEO INPUT jack on your TV (or AV amplifier).

2. Connect audio cables (white and red) between the AV AUDIO OUT jacks on DVD Recorder and AUDIO IN jacks on TV (or AV amplifier).

● You will enjoy high quality images.

yellow

- English

Case 3 : Component Video

COMPONENT

output jacks

1. Connect Component video cables(not supplied) between the COMPONENT OUT(Y,P

DVD Recorder and COMPONENT IN(Y,P

on your TV.

2. Connect audio cables (white and red) between the AUDIO OUT jacks on the DVD Recorder and AUDIO IN jacks on TV (or AV amplifier). (See page 19 to 20).

3. After connecting, refer to the pages 30~31.

● You will enjoy high quality and accurate colour

reproduction images.

green

blue

red

B,PR

red

) jacks on

B,PR

) jacks

green

blue

Other type of connecting the Audio output cable

There are several ways to output audio signal. Select the audio connection that best suits you below.

● Case 1 : Connecting to your TV

● Case 2 : Connecting to a stereo amplifier with AV

output jacks

● Case 3 : Connecting to an AV amplifier with a

digital output jack

Manufactured under licence from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

“DTS” and “DTS Digital Out” are trademarks of DTS, Inc.

Case 1 : Connecting to your TV

If your TV has audio input jacks, use this connection.

Connecting & Setting Up

NOTE

■

Make sure that the colour coded connections match. The Y, P

, P component output jacks of your DVD Recorder must be connected to the exact corresponding component input jacks on your TV.

■

Progressive setting is only available when the DVD Recorder is connected to your TV using component cables.

yellow

white

red

white

yellow

English -

Case 2 : Connecting to a stereo amplifier with AV output jacks

If your stereo amplifier only has AUDIO INPUT jacks(L and R), use the AUDIO OUT jacks.

Case 3: Connecting to an AV amplifier with a digital output jack

If your AV amplifier has a Dolby Digital, MPEG2 or DTS decoder and a digital input jack, use this connection. To enjoy Dolby Digital, MPEG2 or DTS sound, you will need to set up the audio settings. (See pages 29~30)

Connecting & Setting Up

Front(L) speaker

whitered

Front(R) speaker

Rear(L)

Front(L)

Rear(R)

Front(R)

Subwoofer Centre

- English

Connecting to AV 2 IN, DV input jack

This allows you to connect your DVD Recorder to other external devices and view or record their outputs.

● Case 1 : Connecting a VCR, Set-Top Box(STB), DVD

player or Camcorder to the AV 2 IN jacks

● Case 2 : Connecting a Camcorder to the DV IN jack

Case 1 : Connecting a VCR, Set-Top Box(STB), DVD player or Camcorder to the AV 2 IN jacks

Connecting a VCR or external device to AV 2 IN jacks of the DVD Recorder. You can record from connected equipment (VCR, STB, DVD player or Camcorder).

Case 2 : Connecting a Camcorder to the DV IN jack

If your digital camcorder has a DV output jack, connect it to the DV input jack of your DVD Recorder.

Camcorder

■

If the input is not selected automatically,

NOTE

use INPUT SEL. button to select proper input.

Connecting & Setting Up

NOTE

Camcorder

VCR

yellow

STB

DVD

yellow

white

red

■

AV 2INselection will be automatically

white

red

done. If the input is not selected automatically, use INPUT SEL. button to select proper input.

■

Copy protected content cannot be recorded.

English -

System

Setup

On-Screen Menu Navigation

The on-screen menus allow you to enable or disable various functions on your DVD Recorder. Use the following buttons to open and navigate through the on-screen menus.

System Setup

On-Screen Menu Navigation......................22

Plug & Auto Set up.....................................23

Setting the Clock ........................................24

Presetting Channels with the

Auto Setup function....................................24

Presetting Channels with

the Manual Setup function .........................25

Setting Up the Language Options..............26

EP Mode Time Setting ...............................27

Automatic Chapter Creation.......................28

DivX(R) Registration...................................29

Setting Up the Audio Options.....................29

Setting up the Progressive scan ................30

Canceling the Progressive scan.................31

Setting up the Display(Video) Options .......31

Setting up the Parental Control..................32

DVD-Recorder

No Disc

Programme Setup

Scheduled Record List

Programme

RETURNOKMOVE EXIT

√√

DVD-Recorder

DVD-RW(VR)

Title List Playlist Disc Manager Programme Setup

Title List

MENU Button

Press this button on the remote control to open the on-screen MENU. Press again to exit the on-screen MENU.

…… / †† , œœ / √√

Press these buttons on remote control to move the selection bar … / † , œ / √ to cycle through the menu options.

Buttons

OK Button

Press this button on the remote control to confirm any new settings.

RETURN Button

Press this button on the remote control to return to the Previous MENU screen displayed or to exit the on-screen MENU.

Title List

√√

RETURNOKMOVE EXIT

- English

Plug & Auto Set up

Your DVD Recorder will automatically set itself up when it is plugged in for the first time. TV stations and clock will be stored in memory. The process takes a few minutes. Your DVD Recorder will then be ready for use.

Connect the RF cable as indicated on

page 17.

(Connecting Your DVD Recorder to the TV Using the RF Cable and Video/Audio cable.)

Plug the DVD Recorder into the mains.

“Auto” in the front panel display flickers.

Select the language using the …† buttons,

then press the OK button.

Français Deutsch Español Italiano Nederlands

RETURNOKMOVE

Auto Setup

DVD-Recorder

No Disc

Language Set English

Press the OK button or wait for a few

seconds to start the auto setup.

DVD-Recorder

No Disc

Auto Channel scan will be started.

Auto channel memory

Stop

•

The number of stations automatically stored by the DVD Recorder depends on the number of stations that it has found.

17%

Check the date and time.

DVD-Recorder

No Disc

Date Time

JAN 01 2006 12 00

SUN

• if it is : Correct, press the OK button then the date and time will be saved. If you don't press the OK button, the date and time will be saved automatically after 5 seconds.

• if it is :

Incorrect, input correct Time, Date, Year using …†œ √ buttons or number buttons. Press the OK button then the date and time will be saved. When you need to change clock setting, you can set up it manually. (see page 24)

■

Now, DVD Recorder is ready for use. Function for

NOTE

“Plug & Auto Set Up” is fixed already. So if you want to change this fixed one, you can change it by Presetting the Stations in OSD “Presetting Channels with the Manual set up function” menu. (see page 25)

■

Auto Setup function can be performed by pressing and holding down the PROG ( ) buttons on the front panel of the DVD Recorder simultaneously for more than 5 seconds with no disc in the DVD Recorder.

Auto Setup

RETURNOKMOVE

System Setup

Auto setup will be started.

Check antenna and TV cable connection.

RETURNOK

English -

Setting the Clock

Presetting Channels with the Auto Setup function

This menu is used to set the current time. You need to set the time to use timer recording.

System Setup

With the DVD Recorder in Stop mode/No

Disc mode, press the MENU button.

DVD-Recorder

No Disc

Programme Setup

Scheduled Record List

Programme

√√

RETURNOKMOVE EXIT

Press the …† buttons to select Setup, then press the OK or √ button.

RETURNOKMOVE EXIT

Setup

√√

DVD-Recorder

No Disc

Programme Setup

System Clock Set Language Audio Video Parental Control Install

Press the …† buttons to select Clock Set, then press the OK or √ button.

Use the …†œ √ buttons to input Time, Date or Year. Use number buttons to input clock data directly. The day of the week is displayed automatically.

DVD-Recorder

No Disc

Programme Setup

Date Time

JAN 01 2006 12 00

SUN

Clock Set

This feature allows you to manually set the DVD Recorder tuner band to Antenna or Cable, whichever you connected to the Antenna In jack during initial setup.

With the DVD Recorder in Stop mode/No

Disc mode, press the MENU button.

DVD-Recorder

No Disc

Programme Setup

Scheduled Record List

Programme

√√

RETURNOKMOVE EXIT

Press the …† buttons to select Setup, then

press the OK or √ button.

RETURNOKMOVE EXIT

Setup

√√

DVD-Recorder

No Disc

Programme Setup

System Clock Set Language Audio Video Parental Control Install

Press the …† buttons to select Install, then

press the OK or √ button.

DVD-Recorder

No Disc

Programme Setup

Auto Setup Manual Setup

Install

√√

- English

RETURNOKMOVE EXIT

Press the OK button, then the date and

time will be saved.

If you don’t press the OK button, it will not be saved.

RETURNOKMOVE EXIT

Press the …† buttons to select Auto

Setup, then press the OK or √ button.

The message “Your data will be lost. Press [OK] to continue, [MENU] to exit.” is displayed.

Presetting Channels with the Manual Setup function

DVD-Recorder

No Disc

Programme

Auto Setup Manual Setup

Setup

Your data will be lost.

Press [OK] to continue, [MENU] to exit.

RETURNOKMOVE EXIT

Press the OK button to continue.

If you want to exit, press the MENU button.

Auto channel memory

Stop

Channel scan will be started.

Press the OK button to stop the Auto Setup.

Install

√√

You can add preset channel that Auto Channel Search missed. And you can delete a channel you wish to remove. You can programme the order of channels.

With the DVD Recorder in Stop mode/No

Disc mode, press the MENU button.

DVD-Recorder

No Disc

Programme

Scheduled Record List

Setup

17%

Programme

RETURNOKMOVE EXIT

√√

System Setup

Press the …† buttons to select Setup, then

press the OK or √ button.

RETURNOKMOVE EXIT

Setup

√√

DVD-Recorder

No Disc

Programme Setup

System Clock Set Language Audio Video Parental Control Install

Press the …† buttons to select Install, then

press the OK or √ button.

RETURNOKMOVE EXIT

Install

√√

DVD-Recorder

No Disc

Programme Setup

Auto Setup Manual Setup

English -

System Setup

Press the …† buttons to select Manual Setup, then press the OK or √ button.

Manual Setup

PR CH Name Edit

01 --- ---02 --- ---03 --- ---04 --- ---05 --- ---06 --- ---07 --- ----

RETURNOKMOVE EXIT

√√ √√ √√ √√ √√ √√ √√

Press the …† buttons to select a PR

(programme) you wish to edit, delete, or

swap, then press the OK or √ button. Select Edit, Delete or Swap using the …† buttons, then press the OK or √ button.

Manual Setup

PR CH Name Edit

01 --- ---02 --- ---03 --- ---04 --- ---05 --- ---06 --- ---07 --- ----

Edit Delete Swap

RETURNOKMOVE EXIT

√√ √√ √√ √√ √√ √√ √√

Setting up the Language Options

If you set the audio, subtitle, disc menu, on-screen menu and DivX subtitle language in advance, they will come up automatically every time you watch a movie. If the selected language is not recorded on the disc, the original pre-recorded language is selected.

With the DVD Recorder in Stop mode/No

Disc mode, press the MENU button.

DVD-Recorder

No Disc

Programme Setup

Scheduled Record List

Programme

√√

RETURNOKMOVE EXIT

• Edit : Youcan add or edit PR(programme).

After changing PR informations(CH, Name, MFT), select Done, then press the OK button.

Manual Setup

√√

- - - -

Name

--- ---

MFT

Done

OKMOVE

- CH : Tune the channel using œ √ buttons.

- Name : Display station name automatically detected

in broadcasting signal. If not detected, you can edit name by using …†œ √ buttons.

- MFT : You can tune up the channel frequency better

using œ √ buttons.

• Delete : The channel information of selected

PR(programme) will be removed.

• Swap : You can swap the channel information of two

PR(programme). For example, if you wish to swap PR2 and PR5, select swap at PR2, then press the OK button at PR5.

Press the …† buttons to select Setup, then

press the OK or √ button.

RETURNOKMOVE EXIT

Setup

√√

DVD-Recorder

No Disc

Programme Setup

System Clock Set Language Audio Video Parental Control Install

Press the …† buttons to select Language,

then press the OK or √ button.

Language setup menu will be displayed.

DVD-Recorder

No Disc

Programme Setup

Audio : Original Subtitle : Automatic Disc Menu : English On-Screen Menu : English DivX Subtitle : Western

Language

RETURNOKMOVE EXIT

√√

- English

Press the …† buttons to select the desired

language option, then press the OK or √

button.

● Audio : For the speaker sound.

● Subtitle : For the disc subtitles.

● Disc Menu : For the disc menu

contained on the disc

● On-Screen Menu : For the screen of your DVD

Recorder

● DivX Subtitle : Selecting a supported DivX subtitle

language by region.

EP Mode Time Setting

You can select one of four recording modes by pressing the REC MODE button repeatedly. EP mode is one of four REC Mode (XP,SP,LP,EP). In EP(Extended Play) mode, you can set recording time to 6 or 8 hours by this setting.

Afrikaans, Basque, Catalan, Danish, Dutch,

Western

English, Faeroese, Finnish, French, German, Icelandic, Indonesian, Italian, Malay, Norwegian, Portuguese, Spanish, Swahili and Swedish

English, Albanian, Croatian, Czech, Hungarian,

Central

Polish, Romanian, Serbian(Latin), Slovak and Slovenian

Greek

Cyrillic

English and Greek

English, Azeri, Belarusian, Bulgarian, Kazakh, Macedonian, Russian, Serbian, Tatar, Ukrainian and Uzbek

Press the …† buttons to select the desired

language, then press the OK or √ button.

Language

Original English Français Deutsch Español Italiano Nederlands Korean

RETURNOKMOVE EXIT

……

√√

††

NOTE

DVD-Recorder

No Disc

Programme

Audio : Original

Setup

Subtitle : Automatic Disc Menu : English On-Screen Menu : English DivX Subtitle Western

■

Press the RETURN or œ button to return to the previous menu. Press the MENU button to exit the menu.

■

The selected language will only appear if it is supported on the disc.

■

If the subtitle language is displayed in broken fonts, change DivX Subtitle to the appropriate region. If it still does not work, the format is not supported.

With the DVD Recorder in Stop mode/No

Disc mode, press the MENU button.

DVD-Recorder

No Disc

Programme Setup

Scheduled Record List

Programme

√√

RETURNOKMOVE EXIT

Press the …† buttons to select Setup, then

press the OK or √ button.

RETURNOKMOVE EXIT

Setup

√√

DVD-Recorder

No Disc

Programme Setup

System Clock Set Language Audio Video Parental Control Install

Press the …† buttons to select System,

then press the OK or √ button.

System menu will be displayed.

DVD-Recorder

No Disc

Programme Setup

EP Mode Time : 6 Hours Chapter Creator : Off

System

RETURNOKMOVE EXIT

√√

Press the …† buttons to select EP Mode

Time, then press the OK or √ button.

6 Hours 8 Hours

System

√√

DVD-Recorder

No Disc

Programme Setup

EP Mode Time : 6 Hours Chapter Creator Off

System Setup

RETURNOKMOVE EXIT

Press the …† buttons to select the desired

time, then press the OK or √ button.

English -

Automatic Chapter Creation

A DVD-Video consists of ‘Titles’ and ‘Chapters’. When you record one programme, it makes one Title. If you use this function, the title will be divided into chapers.

(V mode)

With the DVD Recorder in Stop mode,

press the MENU button.

DVD-Recorder

DVD-RW(V)

Title List Disc Manager Programme Setup

Title List

√√

Press the …† buttons to select On or Off,

then press the OK or √ button.

• Off : Select this option when you do not want

(Automatic Chapter Creation).

• On : Select this option when you want (Automatic

Chapter Creation).

Press the REC button to start recording.

(See page 37 about how to set recording mode) The message “Do you want to create the chapter menu after this recording?” is displayed.

Do you want to create the chapter menu

after this recording?

Yes

System Setup

RETURNOKMOVE EXIT

Press the …† buttons to select Setup, then press the OK or √ button.

RETURNOKMOVE EXIT

Setup

√√

DVD-Recorder

DVD-RW(V)

Title List Disc Manager Programme

Setup

System Clock Set Language Audio Video Parental Control Install

Press the …† buttons to select System, then press the OK or √ button.

System menu will be displayed.

DVD-Recorder

DVD-RW(V)

Title List Disc Manager Programme Setup

EP Mode Time : 6 Hours Chapter Creator : Off

System

RETURNOKMOVE EXIT

√√

Press the …† buttons to select Chapter Creator, then press the OK or √ button.

DVD-Recorder

DVD-RW(V)

Title List Disc Manager Programme Setup

EP Mode Time : 6 Hours Chapter Creator : Off

System

√√

Off On

Press the œ √ buttons to select Yes and press the OK button.

• A new chapter is created according to the selected recording mode. A chapter will be about 5 minutes long in XP and SP, and about 15 minutes long in LP and EP mode.

Press the STOP button to stop recording.

To display the created chapters, finalise the disc (see page 81) and then press the

DISC MENU button. The chapter menu will

be displayed.

1/1

123

NextTop

CAUTION

■

The Automatic Chapter Creation function does not work during Timer Recording or when you turn the power off.

■

DVD-R discs cannot be unfinalised.

- English

RETURNOKMOVE EXIT

DivX(R) Registration

Press the …† buttons to select the desired

audio option, then press the OK or √

button.

Please use the Registration code to register this DVD Recorder with the DivX(R) Video On Demand format. For more information, visit www.divx.com/vod

Setting up the Audio Options

You can connect the DVD Recorder to an external amp or Home Theatre. Allow you to setup the Audio device and sound status depending on the audio system in use.

With the DVD Recorder in Stop mode/No

Disc mode, press the MENU button.

DVD-Recorder

No Disc

Programme

Scheduled Record List

Setup

Press the …† buttons to select Setup, then

press the OK or √ button.

DVD-Recorder

No Disc

Programme

System Clock Set

Setup

Language Audio Video Parental Control Install

Programme

RETURNOKMOVE EXIT

Setup

√√

DVD-Recorder

No Disc

Programme Setup

Digital Output : PCM DTS : Off Dynamic Compression NICAM : On

Audio

PCM Bitstream

: On

RETURNOKMOVE EXIT

√√

Press the …† buttons to select the desired

item, then press the OK or √ button.

■

Press the RETURN or œ button to return

NOTE

to the previous menu. Press the MENU button to exit the menu.

Audio Options

Digital Output

1. PCM : Select this when you have no equipment that

2. Bitstream :Output Dolby Digital (or MPEG-2) audio as

NOTE

can decode Dolby Digital (or MPEG-2) signal. When you play Dolby Digital (or MPEG-2) sound track, the digital output are converted to PCM Stereo.

bitstream. Select this when your AV receiver or AV amplifier have Dolby Digital (or MPEG-2) Decoder.

■

Digital output setting is equally applied to both Dolby Digital and MPEG-2 audio. LPCM sound track is always outputted as PCM. It has no relation with Digital Output setting.

■

Be sure to select the correct Digital Output or you will hear no sound or loud noise.

System Setup

Press the …† buttons to select Audio, then

press the OK or √ button.

Audio setup menu will be displayed.

: On

RETURNOKMOVE EXIT

Audio

√√

DVD-Recorder

No Disc

Programme Setup

Digital Output : PCM DTS : Off Dynamic Compression NICAM : On

DTS

1. Off : Doesn’t output DTS signal.

Select this when your AV receiver or AV amplifier does not have DTS decoder.

2. On :Outputs DTS Bitstream via digital output when you

play DTS track. Select this only when your AV receiver (or AV amplifier) have DTS decoder.

■

When DTS soundtrack is played, sound

NOTE

does not output from AV Audio Output.

English -

Dynamic Compression

This is only active when a Dolby Digital signal is detected.

1. On :When Movie soundtracks are played at low

volume or from smaller speakers, the system can apply appropriate compression to make low-level content more intelligible and prevent dramatic passages from getting too loud.

2. Off : You can enjoy the movie with the standard

Dynamic Range.

Setting up the Progressive scan

If the TV supports Progressive Scan, press the P.SCAN button on the front of the DVD Recorder to enjoy.

NICAM

NICAM programmes are divided into 3 types. NICAM Stereo, NICAM Mono and Bilingual (transmission in another language). NICAM programmes are always accompanied by a standard mono sound broadcast and you can select the desired sound by setting NICAM on or off.

1. On : NICAM mode

2. Off : Only set at this position to record the standard

System Setup

mono sound during a NICAM broadcast if the stereo sound is distorted due to inferior reception conditions.

With the DVD Recorder in Stop mode,

press the P.SCAN button on the front of the

DVD Recorder.

The message “Press [Yes] to confirm Progressive scan mode. Otherwise press [No]” will appear.

Press [Yes] to confirm Progressive scan mode.

Otherwise press [No]

Yes

Press the œ √ buttons to select Yes, and

then press the OK button.

Set your TV to Progressive input (using the

TV remote control.)

■

Do not press the P.SCAN button if you

NOTE

are using a TV that does not support Progressive mode. Nothing will be displayed on the screen if pressed.

■

Progressive setting is only available when the DVD Recorder is connected to your TV using component cables.

■

If the P.SCAN button on the DVD recorder’s front panel is pressed during playback, the prohibition mark( ) appears on the screen.

■

Progressive setting is only available when the DVD recorder is in stop mode.

- English

+ 148 hidden pages