Samsung DVD-R130, DVD-R131 User Manual [el]

Instruction Manual

DVD-R120/R121

DVD-R128, R129
DVD-R130, R131

English

www.samsung.com

AK68-01003E-00

Warning

IMPORTANT NOTE

The mains lead on this equipment is supplied with a
moulded plug incorporating a fuse. The value of the
fuse is indicated on the pin face of the plug. If it requires
replacing, a fuse approved to BS1362 of the same
rating must be used.

Getting Started

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE THE COVER(OR BACK).
NO USER-SERVICEABLE PARTS ARE INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.

Do not install this equipment in a confined space
such as a bookcase or similar unit.

WARNING : To prevent damage which may result in

CAUTION : DVD RECORDER USES AN INVISIBLE

CAUTION

THIS PRODUCT UTILIZES A LASER.
USE OF CONTROLS OR ADJUSTMENTS OR
PERFORMANCE OF PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR
YOURSELF. REFER SERVICING TO QUALIFIED
PERSONNEL.

This symbol indicates “dangerous
voltage” inside the product that presents
a risk of electric shock or personal injury.

This symbol indicates important
instructions accompanying the product.

fire or electric shock hazard, do not
expose this appliance to rain or
moisture.

LASER BEAM WHICH CAN CAUSE
HAZARDOUS RADIATION EXPOSURE
IF DIRECTED.
BE SURE TO OPERATE RECORDER
CORRECTLY AS INSTRUCTED.

Never use the plug with the fuse cover omitted if the cover
is detachable. If a replacement fuse cover is
required, it must be of the same colour as the pin face of
the plug. Replacement covers are available from your
dealer.

If the fitted plug is not suitable for the power points in your
house or the cable is not long enough to reach a
power point, you should obtain a suitable safety approved
extension lead or consult your dealer for assistance.

However, if there is no alternative to cutting off the plug,
remove the fuse and then safely dispose of the
plug. Do not connect the plug to a mains jack, as there is a
risk of shock hazard from the bared flexible cord.

To disconnect the apparatus from the mains, the plug must
be pulled out from the mains socket, therefore the mains
plug shall be readily operable.

The product unit accompanying this user manual is
licensed under certain intellectual property rights of certain
third parties. This license is limited to private non­commercial use by end-user consumers for licensed
contents.
No rights are granted for commercial use.
The license does not cover any product unit other than this
product unit and the license does not extend to any
unlicensed product unit or process conforming to ISO/IEC
11172-3 or ISO/IEC 13818-3 used or sold in combination
with this product unit. The license only covers the use of
this product unit to encode and/or decode audio files
conforming to the ISO/IEC 11172-3 or ISO/IEC 13818-3.
No rights are granted under this license for product features
or functions that do not conform to the ISO/IEC 11172-3 or
ISO/IEC 13818-3.

This product satisfies CE regulations when shielded
cables and connectors are used to connect the unit
to other equipment. To prevent electromagnetic
interference with electric appliances, such as radios
and televisions, use shielded cables and connectors
for connections.

2

- English

Precaution

Important Safety Instructions

Read these operating instructions carefully before using
the DVD Recorder. Follow all the safety instructions
listed below. Keep these operating instructions handy
for future reference.

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings, Install in
accordance with the manufacturer's instructions.

8) Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or
grounding- type plug. A polarized plug has two
blades with one wider than the other. A grounding­type plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. if the provided plug does not
fit into your outlet, consult an electrician for
replacement of the obsolete outlet.

10) Protect the power cord from being walked on or

pinched particularly at plugs, convenience
receptacles, the point where they exit from the
apparatus.

11) Only use attachments/accessories specified by the

manufacturer.

12) Use only with the cart, stand, tripod, bracket, or

table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid
injury from tip-over.

13) Unplug this apparatus during lightning storms or

when unused for long periods of time.

14) Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.

●

Exterior interference such as lightning and static
electricity can affect normal operation of this DVD
Recorder. If this occurs, turn the DVD Recorder off
and on again with the STANDBY/ON button, or
disconnect and then reconnect the AC power cord to
the AC power outlet.
The DVD Recorder will operate normally.

●

Be sure to remove the disc and turn off the DVD
Recorder after use.

●

Disconnect the AC power cord from the AC outlet
when you don’t intend to use the DVD Recorder for
long periods of time.

●

Clean the disc by wiping in a straight line from the
inside to the outside of the disc.

Maintenance of Cabinet

For safety reasons, be sure to disconnect the AC power
cord from the AC outlet.

●

Do not use benzene, thinner, or other solvents for
cleaning.

●

Wipe the cabinet with a soft cloth.

Disc Handling

●

Use discs with regular
shapes. If an irregular disc
(a disc with a special shape) is used, this DVD
recorder may be damaged.

Holding discs

●

Avoid touching the surface of a
disc where recording is performed.

DVD-RW, DVD-R

●

Clean with an optional DVD­RAM/PD disc cleaner (LF­K200DCA1 where available).
Do not use cleaners or cloths
for CDs to clean DVD-RW/
DVD-R discs.

DVD-Video, Audio CD

●

Wipe off dirt or contamination on the disc with a soft
cloth.

Cautions on handling discs

Getting Started

Handling Cautions

●

Before connecting other components to this DVD
Recorder, be sure to turn them all off.

●

Do not move the DVD Recorder while a disc is being
played, or the disc may be scratched or broken, the
DVD Recorder's internal parts may be damaged.

●

Do not put a flower vase filled with water or any small
metal objects on the DVD Recorder.

●

Be careful not to put your hand into the disc tray.

●

Do not place anything other than the disc in the disc
tray.

●

Do not write on the printed side with a ball-point pen
or pencil.

●

Do not use record cleaning sprays or antistatic.
Also, do not use volatile chemicals, such as benzene
or thinner.

●

Do not apply labels or stickers to discs. (Do not use
discs fixed with exposed tape adhesive or leftover
peeled-off stickers.)

●

Do not use scratch-proof protectors or covers.

●

Do not use discs printed with label printers available
on the market.

●

Do not load warped or cracked discs.

English -

3

Disc Storage

Be careful not to harm the disc because the data on
these discs is highly vulnerable to the environment.

●

Do not keep under direct sunlight.

●

Keep in a cool ventilated area.

●

Store vertically.

●

Getting Started

Keep in a clean protection jacket.

●

If you move your DVD recorder suddenly from a cold
place to a warm place, condensation may generate
on the operating parts and lens and cause abnormal
disc playback. If this occurs, do not connect the plug
to the power outlet and wait for two hours. Then
insert the disc and try to play back again.

Disc Specifications

DVD-Video

●

A digital versatile disc (DVD) can contain up to
135-minutes of images, 8 audio languages and 32
subtitle languages. It is equipped with MPEG-2
picture compression and Dolby digital surrounding,
allowing you to enjoy vivid and clear theatre quality
images in the comfort of your own home.

●

When switching from the first layer to the second
layer of a dual-layered DVD Video disc, there may be
momentary distortion in the image and sound.
This is not a malfunction of the DVD Recorder.

●

Once a DVD-R/-RW recorded in Video Mode is
finalised, it becomes DVD-Video.

Audio CD

●

An audio disc on which 44.1kHz PCM Audio is
recorded

●

Plays CD-DA format audio CD-R and CD-RW discs.
The DVD Recorder may not be able to play some
CD-R or CD-RW discs due to the condition of the
recording.

CD-R/-RW

MP3 CD-R/-RW

●

Only CD-R discs with MP3 files recorded with
ISO9660 or JOLIET format can be played back

●

Only MP3 files with the ".mp3", ".MP3" extension can
be used.

●

For MP3 files recorded with a VBR(Variable Bit
Rates), from 32 Kbps to 320 Kbps, the sound may
cut in out.

●

Playable bitrate range is from 56Kbps to 320Kbps.

●

This DVD Recorder can handle a maximum of 500
files and 100 folders.

JPEG CD-R/-RW

●

Only JPEG files with the ".jpg", ".JPG" extension can
be used.

●

This DVD Recorder can handle a maximum of 500
files and 100 folders.

●

Maximum size of progressive JPEG is 3M pixels.

●

MOTION JPEG is not supported.

Using CD-R/-RW

●

Use a 700MB(80 minutes) CD-R/-RW disc. If
possible, do not use a 800MB(90 minutes) or above
disc, as the disc may not play back.

●

If the CD-R/-RW disc was not recorded as a closed
session, you may experience a delay in the early
playback time, all recorded files may not play.

●

Some CD-R/-RW discs may not be playable with this
DVD Recorder, depending on the device which was
used to burn them. For contents recorded on CD-R/­RW media from CDs for your personal use, playability
may vary depending on contents and discs.

Using MPEG4 disc

●

Disc : CD-R/-RW, DVD-R/-RW

●

MPEG4 File with following extensions can be played.
: .avi, .divx, .AVI, .DIVX

●

MPEG4 Codec format : DivX 3.11 DivX 4.x DivX 5.x
DivX-Pro Xvid

●

Motion Compensation : QPEL, GMC

●

four CC : MPG4, mpg4, DIV3, divX3, DIVX, divX,
DX50, MP43, mp43, XVID, xvid

●

Available Audio Format : “MP3”, “MPEG1 Audio Layer2”,
“LPCM”, “AC3”, “DTS”, “MS ADPCM”

●

Supported subtitle file formats: .smi, .srt, .sub, .psb, .txt, .ass

DVD-R Disc Playback and Recording

●

Once a DVD-R recorded in Video Mode is finalised, it
becomes DVD-Video.

●

You can record onto the available space on the disc
and perform editing functions such as giving titles to
discs and programmes and erasing programmes
before finalising.

●

When programming is erased from a DVD-R, that
space does not become available. Once an area on
a DVD-R is recorded on, that area is no longer
available for recording, whether the recording is
erased or not.

●

It takes about 30 seconds for the DVD Recorder to
complete recording management information after
recording finishes.

●

This DVD Recorder optimizes the DVD-R for each
recording. Optimizing is carried out when you start
recording after inserting the disc or turning on the
DVD Recorder. Recording onto the disc may become
impossible if optimizing is carried out too many times.

●

Playback may be impossible in some cases due to
the condition of recording.

●

This DVD Recorder can play back DVD-R discs
recorded and finalised with a Samsung DVD video
recorder. It may not be able to play some DVD-R
discs depending on the disc and the condition of the
recording.

DVD-RW Disc Playback and Recording

●

Recording and playback can be performed on DVD­RW discs in both the Video and VR Modes.

●

Once a DVD-RW recorded in both the Video and VR
Modes is finalised, you cannot perform addtional
recording.

●

Once a DVD-RW recorded in Video Mode is finalised,
it becomes DVD-Video.

●

In both modes, playback can be performed before
and after finalisation, but additional recording,
deleting and editing can not be performed after
finalisation.

4

- English

●

If you want to record the disc in VR Mode and then
record in V Mode, be sure to execute Format.
Be careful when executing Format because all the
recorded data may be lost.

●

A DVD-RW blank disc is initialized to VR Mode when
first initialized.

●

DVD-RW (VR mode)

- This is a format that is used for recording data on a

DVD-RW disc. You can record multiple titles, edit,
delete, partial delete, create a playlist, etc.

- A disc that is recorded in this mode may not be

played by existing DVD Recorder.

●

DVD-RW (Video mode)

- This is a format that is used for recording data on a

DVD-RW or DVD-R disc. The disc can be played
by existing DVD Recorder once it has been
finalised.

- If a disc that has been recorded in Video Mode by a

different maker’s recorder but has not been
finalised, it cannot be played or additionally be
recorded by this DVD Recorder.

COPY PROTECTION

●

Many DVD discs are encoded with copy protection.
Because of this, you should only connect your DVD
recorder directly to your TV, not to a VCR.
Connecting to a VCR results in a distorted picture
from copy-protected DVD discs.

●

This DVD Recorder incorporates copyright
protection technology that is protected by methods
claims of certain U.S. patents and other intellectual
property rights owned by Macrovision Corporation
and other rights owners. Use of this copyright
protection technology must be authorised by
Macrovision Corporation, is intended for home and
other limited viewing uses only unless otherwise
authorised by Macrovision Corporation.
Reverse engineering or disassembly is prohibited.

Do not use the following discs!

●

LD, CD-G, CD-I, Video-CD, CD-ROM, and DVD-ROM
discs should not be used in this DVD Recorder.
[Note]
Disc types that can be played : CD/CD-R/CD-RW/
MP3/JPEG/MPEG4/DVD-Video/DVD-RW/DVD-R.
For a DVD-R/DVD-RW disc, which has been
recorded in Video Mode on another component, it
can play only when finalised.

●

Some commercial discs and DVD discs purchased
outside your region may not be playable with this DVD
Recorder. When these discs are played, either “No Disc”
or "Please check the regional code." will be displayed.

●

If your DVD-RW disc is an illegal copy or is not in
DVD video format, it may also not be playable.

Disc Compatibility

●

High Speed Recording discs can be used in this DVD
Recorder.

●

Not all brands of discs will be compatible with this
DVD Recorder.

Getting Started

Protection

This DVD Recorder can allow you to protect the
contents of your discs, as described below.

●

Programme-protected: See page 70
“Locking(Protecting) a Title”

●

Disc-protected: See page 82 “Disc Protection”

DVD-RW/DVD-R discs that are incompatible with the

✻

DVD-VIDEO format cannot be played with this DVD
Recorder.

✻ For more information on DVD recording compatibility,

consult your DVD-RW/DVD-R manufacturer.

✻ Use of poor quality DVD-RW/DVD-R discs may

cause following unexpected problems including,
without limitation, recording failure, loss of recorded
or edited materials or damage to the DVD Recorder.

English -

5

Contents

Getting Started

Getting Started

Getting Started

Warning........................................................................2

Precaution...................................................................3

Important Safety Instructions.............................................3

Handling Cautions..............................................................3

Maintenance of Cabinet.....................................................3

Disc Handling .....................................................................3

Disc Storage .......................................................................4

Disc Specifications .............................................................4

General Features........................................................8

Before reading the user’s manual...........................9

How to use the DVD Recorder.................................9

Unpacking .................................................................11

Accessories.......................................................................11

Preparing the Remote Control.........................................11

Setting the Remote Control .............................................11

Description................................................................13

Front Panel(DVD-R128) .................................................13

Front Panel(DVD-R129) .................................................13

Front Panel(DVD-R130) .................................................14

Front Panel(DVD-R131) .................................................14

Front Panel Display .........................................................15

Rear Panel........................................................................15

Tour of the Remote Control .............................................16

Connecting & Setting Up

Connecting & Setting Up

Quick Overview........................................................17

Connecting the DVD Recorder..............................18

Additional connections...........................................18

Antenna + DVD Recorder +

external decoder box + TV ....................................19

Other type of connecting

the Video output cable............................................19

Case 1 : Connecting to a Video (Composite)

output jack ........................................................20

Case 2 : Connecting to an S-Video output jack.............20

Case 3 : Component Video output jacks........................21

Other type of connecting the Audio output cable..

Case 1 : Connecting to your TV......................................21

Case 2 : Connecting to a stereo amplifier with AV

output jacks .....................................................22

Case 3: Connecting to an AV amplifier with a digital

output jack ........................................................22

21

Connecting to AV3 IN, DV input jack

(DVD-R130, R131 only)............................................23

Case 1 : Connecting a VCR, Set-Top Box(STB), DVD

player or Camcorder to the AV3 IN jacks ......23

Case 2 : Connecting a Camcorder to the DV IN jack

(DVD-R130, R131 only)...................................................23

System Setup

System Setup

On-Screen Menu Navigation..................................24

Plug & Auto Setup...................................................25

Setting the Clock......................................................26

Presetting Channels with the Auto Setup

function......................................................................27

Presetting Channels with the Manual Setup

function......................................................................28

Setting up the Language Options.........................29

EP Mode Time Setting ............................................30

Automatic Chapter Creation..................................31

Quick Recording Setting ........................................32

DivX(R) Registration................................................32

Setting up the Audio Options................................32

Audio Options...................................................................33

Setting up Video Output Options..........................34

Setting up the Progressive scan...........................35

Canceling the Progressive scan...........................35

Setting up the Display(Video) Options.................36

6

- English

Display(Video) Options ....................................................36

Setting up the Parental Control.............................37

If you forgot your password.............................................37

About the Rating Level ....................................................38

About the Change Password ..........................................38

Recording

Recording

Before Recording.....................................................39

Recordable discs..............................................................39

Recording Formats ..........................................................40

Recording Mode...............................................................40

Unrecordable video..........................................................40

About INFO Button...........................................................41

Checking the available disc space (Disc Information)...41

Recording the current TV programme you are

watching....................................................................41

Recording from external equipment you are

watching....................................................................43

Copying from a Camcorder

(DVD-R130, R131 only)............................................43

Making a One Touch Recording (OTR)................44

Making a Timer Recording.....................................45

Flexible Recording (for Timer recording only) ...46

Editing the Scheduled Record List.......................47

Deleting the Scheduled Record List.....................47

Recording the Standard Timer List ......................48

Playback

Playback

Before Playing..........................................................49

Region code (DVD-Video only).......................................49

Disc types that can be played .........................................49

Discs that cannot be played ............................................49

Playing a Disc...........................................................50

Using the Disc Menu & Title Menu .................................51

Using the Search Functions ............................................51

Slow Motion Play..............................................................52

Step Motion Play..............................................................52

About ANYKEY ................................................................52

Using the Repeat Function..............................................53

Selecting the Subtitle .......................................................55

Selecting the Audio language..........................................55

Changing the Camera Angle...........................................56

Zooming-In........................................................................56

Using Bookmarks.............................................................57

Using Markers ..................................................................58

Playing an Audio CD/MP3 .....................................59

Playing an Audio CD (CD-DA)/MP3...............................59

Playing a Picture......................................................63

Playing a MPEG4 .....................................................64

Playing the Title List................................................65

Editing

Editing

Basic Editing (Title List)...................................................69

Renaming(Labeling) a Title..............................................69

Locking(Protecting) a Title...............................................70

Deleting a Title..................................................................70

Deleting a Section of a Title.............................................71

Advanced Editing (Playlist) .............................................

Creating a Playlist ............................................................73

Playing Entries in the Playlist ..........................................74

Renaming a Playlist Entry ...............................................75

Editing a Scene for the Playlist .......................................76

Copying a Playlist Entry to the Playlist ...........................79

Deleting a Playlist Entry from the Playlist.......................80

Disc Manager

Editing the Disc Name .....................................................81

Disc Protection .................................................................82

Formatting a Disc.............................................................82

Delete All Title Lists ..........................................................83

Finalising a disc................................................................84

Unfinalising a disc (V/VR mode) .....................................85

Additional Information

Additional Information

..............................................................81

73

Troubleshooting.......................................................86

Specifications...........................................................90

Getting Started

English -

7

General Features

High quality progressive scan

Progressive scanning provides high resolution and
flicker free video. The 10-bit 54-MHz DAC and 2D Y/C
Separating Circuitry provides the highest image
playback and recording quality. (See pages 21, 35)

Getting Started

The DVD Recorder allows you to record and play high
quality digital video on DVD-RW/DVD-R discs. You can
record and edit digital images on DVD-RW/DVD-R
discs as if they were VCR tapes.

High quality digital audio and video recording
and playback

Record up to 8-hours of images with a 4.7 GB
DVD-RW/DVD-R disc, depending on the recording
mode.

Selectable Recording Mode

You can set your recorder to one of four different
recording speeds, each varying in recording quality and
length. EP (6Hr or 8Hr) mode yields the most recording
time, LP & SP modes provide less recording time with
higher quality recording, XP mode gives you the highest
quality recording.

Automated Quality Adjustment for Timer
Recording

If FR mode is selected, the video quality is adjusted
automatically so that all video for the scheduled time
can be recorded onto the free disc space.
(See page 46.)

A variety of functions with an easy-to-use user
interface

The integrated menu system and the messaging
function allow you to perform desired operations both
easily and conveniently. With a DVD-RW disc, you can
edit recorded video, create a playlist, edit video in a
specific sequence according to your requirements.

MPEG4 playback

This DVD Recorder can play MPEG4 formats within an
avi file.

DivX Certification

DivX, DivX Certified, and associated
logos are trademarks of DivXNetworks,
Inc and are used under licence.

Creating a DVD video title using
DVD-RW/DVD-R disc

With the DVD Recorder, you can create your own DVD
Video titles on 4.7 GB DVD-RW/DVD-R discs.

Copying data from a digital camcorder using a
DV input jack (DVD-R130, R131 only)

Record DV Device video onto DVD-RW, DVD-R discs
using the DV input jack (IEEE 1394-4pin/4pin).
(See pages 43-44.)

8

- English

Before reading the user’s manual

Make sure to check the following terms before
reading the user’s manual.

How to use the DVD Recorder

Step 1

Select the disc type

Getting Started

Icons that will be used in manual

Icon Term Definition

This involves a function available

DVD

JPEG in a data picture CD-R/-RW,

MP3

MPEG4

Caution function does not operate or

NOTE on the page that help each

One-Touch

button by using only one button.

ANYKEY A function that can be operated

button by using ANYKEY button.

About the use of this user’s manual

1) Be sure to be familiar with Safety Instructions before
using this DVD Recorder. (See pages 2-5)

2) If a problem occurs, check for Troubleshooting.
(See pages 86-89.)

Copyright

©2006 Samsung Electronics Co.
All rights reserved; No part or whole of this user’s
manual may be reproduced or copied without the prior
written permission of Samsung Electronics Co.

in DVD or DVD-R/DVD-RW
discs that have been recorded
and finalised in Video Mode.

This involves a function available

RW

in DVD-RW.

This involves a function available

R

in DVD-R.

This involves a function available

CD

in a data CD (CD-R or CD-RW).

This involves a function available

DVD-R/-RW.

This involves a function available
in a data CD-R/-RW,DVD-R/-RW.

This involves a function available
in a data CD-R/-RW,DVD-R/-RW.

This involves a case where a

settings may be cancelled.

This involves tips or instructions

function operate.

A function that can be operated

This DVD Recorder can record on the following types
of discs.
If you want to repeatedly record on the same disc or
you want to edit the disc after recording, select a
rewritable DVD-RW type disc.
If you want to save recording without any change,
choose a non-rewritable DVD-R.

Step 2

Unlike a VCR, the DVD Recorder automatically starts
formatting when an unused disc is inserted. This is
required for the preparation of recording on a disc.

Using a DVD-RW

This type of disc can be formatted in either DVD-Video
format (Video mode) or DVD-Video Recording format
(VR mode). For an unused disc, a message that asks
whether to format in VR Mode or not is displayed.
You can play a Video mode disc on various DVD
components. A VR mode disc allows more varied
editing.

Using a DVD-R

Formatting a disc is unnecessary and only Video
Mode Recording is supported. You can play this type
of discs on various DVD components only when they
have been finalised.

NOTE

Format the disc to start recording

■

You can only use either the VR or
Video mode on a DVD-RW, but not
both at the same time.

■

You can change the DVD-RW
format to another format by
reinitializing. It should be noted that
the disc's data will be lost when
changing formats.

English -

9

Step 3

Recording

Step 6

Finalising & Playing on other DVD components

There are two different recording methods, Direct
Recording and Timer Recording. Timer recording is
classified as a Date : Once, Daily, MO-SA, MO-FR,
W-SA, etc.

Getting Started

Recording mode : XP (high quality mode), SP (standard
quality mode), LP (long recording mode), and EP
(extended mode) according to the recording mode. When
recording is set in the FR mode, the best quality picture is
recorded with regards to the remaining time on the disc.

Step 4

You can select the title you want to play in a displayed
menu and then immediately start playback.
A DVD consists of sections called titles, and sub
sections called chapters.
During recording, a title is created between two points
where you start and stop recording. Chapters will be
created automatically when you finalise recording on
DVD-R / DVD-RW discs in Video mode.
The chapter’s length (interval between chapters) varies
according to the recording mode.

Playing

To play your DVD on other DVD components,
finalising may be necessary. First, finish all editing and
recording operations, then finalise the disc.

When using a DVD-RW disc in VR Mode

Although finalising is generally unnecessary when
playing the disc on a VR Mode compatible component,
a finalised disc should be used for playback.

When using a DVD-RW disc in Video Mode

The disc should be finalised first to enable playback on
anything other than this DVD Recorder. No more
editing or recording can be made on the disc once it
has been finalised.

When using a DVD-R disc

You should finalise the disc to play it on a component
other than this DVD Recorder. You cannot edit or
record on the disc once it has been finalised.

Step 5

Editing on discs is easier than conventional video
tapes. The DVD Recorder supports many different edit
functions, possible only with DVDs.

With a simple and easy edit menu, you can operate
various edit functions, such as delete, copy, rename,
lock, etc., on a recorded title.

Creating a playlist (DVD-RW in VR mode)

With this DVD Recorder, you can create a new playlist
on the same disc and edit it without the change of the
original recording.

10

- English

Editing a recorded disc

Unpacking

Getting Started

Accessories

Check for the supplied accessories below.

Video/Audio Cable

Remote Control

Instruction Manual

RF Cable for TV

Batteries for Remote

Control (AAA Size)

Quick Guide

Preparing the Remote Control

Setting the Remote Control

You can control certain functions of another
manufacturer’s TV with this remote control.
Control function buttons involve:

PROG
TV MUTE, INPUT SEL. button.

, VOL +/-, Direct Number buttons,

/

STANDBY/ON,

Install Batteries in the Remote Control

● Open the battery cover on the back of the remote

control.

● Insert two AAA batteries. Make sure that the polarities

(+ and -) are aligned correctly.

● Replace the battery cover.

If the remote does not operate properly:

● Check the polarity +/- of the batteries (Dry-Cell)

● Check if the batteries are drained.

● Check if remote sensor is blocked by obstacles.

● Check if there is any fluorescent lighting nearby.

Dispose of batteries according to local
environmental regulations. Do not put them in the
household trash.

English -

11

To determine whether your television is
compatible, follow the instructions below.

1. Switch your television on.

2. Point the remote control towards the television.

3. Press and hold the STANDBY/ON button and enter

the two-figure code corresponding to the brand of
your television, by pressing the appropriate number

Getting Started

buttons.

Controllable TV Codes

BRAND BUTTON
SAMSUNG 01, 02, 03, 04, 05, 06, 07, 08, 09
AIWA 82
ANAM 10, 11, 12, 13, 14, 15, 16, 17, 18
BANG & OLUFSEN 57
BLAUPUNKT 71
BRANDT 73
BRIONVEGA 57
CGE 52
CONTINENTAL EDISON 75
DAEWOO
EMERSON 64
FERGUSON 73
FINLUX 06, 49, 57
FORMENTI 57
FUJITSU 84
GRADIENTE 70
GRUNDIG 49, 52, 71
HITACHI 60, 72, 73, 75
IMPERIAL 52
JVC 61, 79
LG 06, 19, 20, 21, 22, 78
LOEWE 06, 69
LOEWE OPTA 06, 57
MAGNAVOX 40
METZ 57
MITSUBISHI 06, 48, 62, 65
MIVAR 52, 77
NEC 83
NEWSAN 68
NOBLEX 66
NOKIA 74
NORDMENDE 72, 73, 75
PANASONIC 53, 54, 74, 75
PHILIPS 06, 55, 56, 57
PHONOLA 06, 56, 57
PIONEER 58, 59, 73, 74
RADIOLA 06, 56
RADIOMARELLI 57
RCA 45, 46
REX 74
SABA 57, 72, 73, 74, 75
SALORA 74
SANYO 41, 42, 43, 44, 48
SCHNEIDER 06

BRAND BUTTON
SELECO 74
SHARP 36, 37, 38, 39, 48
SIEMENS 71
SINGER 57
SINUDYNE 57
SONY 35, 48
TELEAVA 73
TELEFUNKEN 67, 73, 75, 76
THOMSON 72, 73, 75
THOMSON ASIA 80, 81
TOSHIBA 47, 48, 49, 50, 51, 52
WEGA 57
YOKO 06
ZENITH 63

Result: If your television is compatible with the remote

control, it will switch off.
It is now programmed to operate with the

19, 20, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34

remote control.

■

NOTE

■

Then you can control the television using the
following buttons after the TV button.

Button Function

STANDBY/ON Used to switch the television on and off.

INPUT SEL. Used to select an external source.

VOL (+ or -) Used to adjust the volume of the television.

PROG ( or ) Used to select the desired channel.

TV MUTE Used to toggle the sound on and off.

0~9 Used to input number directly.

■

NOTE

If several codes are indicated for your
television brand, try each one in turn until
you find one that works.

If you replace the remote control's
batteries, you must set the brand code
again.

The various functions will not necessarily
work on all televisions. If you encounter
problems, operate the television directly.

12

- English

Description

Front Panel (DVD-R128)

Getting Started

1. STANDBY/ON

Turns the DVD Recorder on and off.

2. AV3 IN

Connect external equipment.

3. DISC TRAY

Opens to accept a disc.

4. OPEN/CLOSE

Opens and closes the disc tray.

5. DISPLAY

Displays the playing status, title/chapter/time, etc.

6. SEARCH/SKIP

Go to the next title/chapter/track or go back to the
previous title/chapter/track.

Front Panel (DVD-R129)

7. PLAY/PAUSE

Plays a disc or pauses playback/recording.

8. P.SCAN

Selects the progressive scan mode.

9. PROG ( )

Select TV preset Channels.
Same as PROG button on the remote control.

10.REC

Starts recording.

11. STOP

Stops disc playback.

1. STANDBY/ON

Turns the DVD Recorder on and off.

2. AV3 IN

Connect external equipment.

3. DISC TRAY

Opens to accept a disc.

4. OPEN/CLOSE

Opens and closes the disc tray.

5. DISPLAY

Displays the playing status, title/chapter/time, etc.

6. SEARCH/SKIP

Go to the next title/chapter/track or go back to the
previous title/chapter/track.

7. P.SCAN

Selects the progressive scan mode.

8. PROG ( )

Select TV preset Channels.
Same as PROG button on the remote control.

9. REC

Starts recording.

10.STOP

Stops disc playback.

11. PLAY/PAUSE

Plays a disc or pauses playback/recording.

English -

13

Front Panel (DVD-R130)

Getting Started

1. STANDBY/ON

Turns the DVD Recorder on and off.

2. AV3 IN

Connect external equipment.

3. DV-IN

Connects extermal digital equipment with a DV
jack. (such as a camcorder)

4. DISC TRAY

Opens to accept a disc.

5. OPEN/CLOSE

Opens and closes the disc tray.

6. DISPLAY

Displays the playing status, title/chapter/time, etc.

Front Panel (DVD-R131)

7. SEARCH/SKIP

Go to the next title/chapter/track or go back to the
previous title/chapter/track.

8. PLAY/PAUSE

Plays a disc or pauses playback/recording.

9. P.SCAN

Selects the progressive scan mode.

10.PROG ( )

Select TV preset Channels.
Same as PROG button on the remote control.

11. REC

Starts recording.

12.STOP

Stops disc playback.

1. STANDBY/ON

Turns the DVD Recorder on and off.

2. AV3 IN

Connect external equipment.

3. DV-IN

Connects extermal digital equipment with a DV
jack. (such as a camcorder)

4. DISC TRAY

Opens to accept a disc.

5. OPEN/CLOSE

Opens and closes the disc tray.

6. DISPLAY

Displays the playing status, title/chapter/time, etc.

14

- English

7. SEARCH/SKIP

Go to the next title/chapter/track or go back to the
previous title/chapter/track.

8. PLAY/PAUSE

Plays a disc or pauses playback/recording.

9. P.SCAN

Selects the progressive scan mode.

10.PROG ( )

Select TV preset Channels.
Same as PROG button on the remote control.

11. REC

Starts recording.

12.STOP

Stops disc playback.

Front Panel Display

Getting Started

1. Lights when a disc is loaded.

2. Lights in the record mode.

3. Lights to indicate the timer record mode.

Rear Panel

1. In from aerial connector

2. Out to TV connector

3. AV2(EXT) INPUT SCART Connector

4. AV1(TV) OUTPUT SCART Connector

5. DIGITALAUDIO OUT(OPTICAL)

Connects to an amplifier having a digital optical
audio input jack.

6. DIGITALAUDIO OUT(COAXIAL)

Connects to an amplifier having a digital coaxial
audio input jack.

4. Lights when a DVD-R/-RW disc is loaded.

5. Playing time/clock/current status indicator.

6. Lights in the progressive scan mode.

7. AUDIO OUT

Connects to the audio input of external equipment
using audio cables.

8. VIDEO OUT

Connects the input of external equipment using a
Video cable.

9. S-VIDEO OUT

Connects the input of external equipment using an
S-Video cable.

10. COMPONENT VIDEO OUT

Connects to equipment having Component video
output.

NOTE

■

The Antenna connection does not pass
output signal of DVD. To watch a DVD on
your TV, you must connect audio/video
cables.

English -

15

Tour of the Remote Control

Getting Started

13. ANYKEY Button

Use this to view the status of the disc that is being
played.

14. REC Button

Use to make a recording on DVD-RW/-R discs.

26
27

1

28
29

16
17

15. REC MODE Button

This will display the recording status.(XP/SP/LP/EP)

16. REPEAT Button

Allows you to repeat a title, chapter, track or disc.

17. OPEN/CLOSE Button

To open and close the disc tray.

2

18. SUBTITLE Button

Press this to switch the DVD’s subtitle language.

19. PLAY/PAUSE Button

3

4
5
6
7

8

9

10

11

18

19

20

21

Press to play a disc or pause playback/recording.

20. PROG Buttons

Select preset channels in a specific order.
Same as PROG buttons in front panel.

21. RETURN Button

Returns to a previous menu.

22. PLAY LIST/TITLE MENU Button

Use this to return to the Title menu, or to view the
recorded files list.

23. CANCEL Button

24. MARKER/TIMER Button

Use this to bookmark a position while playing a
disc.
Press to directly enter the Timer Recording Mode
menu while stopping a disc.

25. INFO Button

12
13

14
15

22
23

24
25

This will display current settings or disc status.

26. TV Button

Press this to operate TV.

27. DVD Button

Press this when you use a DVD recorder.

28. INPUT SEL. Button

Select line input signal in external input mode
[PROG, AV input or DV INPUT(DVD-R130, R131 only)]

29. ZOOM Button

Press this to enlarge the screen.

1. STANDBY/ON Button

2. 0~9(Number) Buttons

3. TV/DVD Button

4. Reverse/Forward Skip Buttons

Press to skip a disc backwards or forwards.

5. Reverse/Forward Step Buttons

Press to play frame by frame.

6. Reverse/Forward Search Buttons

Press to search a disc backwards or forwards.

7. STOP Button

Press to stop a disc.

8. VOL Buttons

Volume adjustments.

9. AUDIO/TV MUTE Button

Use this to access various audio functions on a
disc.(DVD mode)
This operates as Sound Mute. (TV mode)

10. MENU Button

Brings up the DVD recorder’s setup menu.

11. OK/DIRECTION(

¥ 

12. TITLE LIST/DISC MENU Button

Use this to enter the View Recording list/Disc menu.

16

- English

) Buttons

Quick Overview

Connecting

& Setting Up

This section involves various methods of
connecting the DVD Recorder to other external
components and required initial setting modes.

A Quick Overview presented in this guide will give you
enough information to start using the DVD Recorder.

Connecting & Setting Up

Connecting the DVD Recoder

†

Additional connections

†

Antenna + DVD Recorder + external
decoder box + TV

†

Other type of connecting the
Video output cable

†

Other type of connecting the Audio
output cable

†

Quick Overview.................................................17

Connecting the DVD Recorder........................18

Additional connections .....................................18

Antenna + DVD Recorder

+ external decoder box + TV ..........................19

Other type of connecting

the Video output cable......................................19

Other type of connecting

the Audio output cable......................................21

Connecting to AV3 IN, DV input jack

(DVD-R130, R131 only)...................................23

Connecting to AV3 IN, DV input jack
(DVD-R130, R131 only)

English -

17

Connecting the DVD Recorder

Additional connections

You can connect your DVD Recorder to the television
using the SCART cable if the appropriate input is
available on the television.

1. Connect the RF cable as shown.

2. Connect one end of the SCART cable to the AV1

socket on the rear of the DVD Recorder.

3. Plug the other end into the appropriate connector on

the television.

4. Plug in the DVD Recorder and TV

Connecting & Setting Up

5.Turn on the DVD Recorder and TV.

6. Press the INPUT SEL. button on your TV remote

control until the Video signal from the DVD Recorder
appears on the TV screen.

To RF IN

To RF OUT

RF Cable

To ANT INPUT

You can connect your DVD Recorder to a satellite or

digital tuner.

external device
(VCR/Satellite receiver)

- DVD mode

1. Connect the AV2 connector of DVD Recorder and
VCR/Satellite receiver or digital tuner using a SCART
cable.

2. Connect the AV1 connector to the SCART AV
connector on TV.

3. Turn on the DVD Recorder, VCR/Satellite receiver or
digital tuner and TV.

4. Set Input mode on AV2.

NOTE

18

- English

■

The RF cable connection of this DVD
Recorder sends only signals of TV.
You must connect SCART cable or
Audio/Video cables to watch a signal from
your DVD Recorder.

■

TV mode
Press the TV/DVD button on remote
control, then “TV” appear on Front LED
display (or turn off DVD Recorder).

- TV mode

1. Press the TV/DVD button on remote control,then
“TV” appear on Front LED display. (or turn off DVD
Recorder.)

2. You can watch programmes from a satellite or digital
tuner connected to this DVD Recorder, even when
the DVD Recorder is turned off.

Antenna + DVD Recorder +

Other type of connecting

external decoder box + TV

If you connect external decoder box to DVD recorder,
you can record scrambled channels (CANAL+or
Premiere broadcasts) received through the built-in TV
tuner in DVD Recorder.

Wall

DECODER

1. Connect RF antenna cables as shown.

2. Connect the AV1 connector on this recorder to the
SCART AV connector on TV using a SCART cable.

3. Connect the AV2 connector to a SCART AV
connector on decoder box.

4. To watch or record PAY-TV Canal Plus programmes,
set your DVD Recorder to receive the channels using
the on-screen display.(Refer to page 28)

the Video output cable

There are several ways to output video signal not using
scart cables. Select one of the following video
connecting that best suits you below.

●

Case 1 : Connecting to a Video (Composite) output

●

Case 2 : Connecting to an S-Video output jack

●

Case 3 : Component Video output jacks

S-Video, Component video and Progressive
Output Modes

●

●

●

jack

S-Video and Component video output are available
only if your TV supports S-Video input or Component
video input, respectively. If S-Video or Component
video output does not work, check the TV
connections and the TV input selection settings.
Compared to standard interlaced video, progressive
scan doubles the amount of video lines fed to your
TV, resulting in a more stable, flicker-free, clear
image than interlaced video.

This is only available with TVs that support
progressive scan.
Progressive Scan Output (576p)
Consumers should note that not all high definition
television sets are fully compatible with this DVD
Recorder and may cause artifacts to be displayed in
the picture, in case of 576 progressive scan picture
problems, It is recommended that the user switch the
connection to the ‘standard definition’ output. If there
are questions regarding our TV set compatibility with
this model 576p DVD Recorder, please contact our
customer service centre.

Connecting & Setting Up

English -

19

Case 1 : Connecting to a Video (Composite) output jack

1. Connect a video(yellow) cable between the VIDEO
(yellow) OUT jack on DVD Recorder and VIDEO
(yellow) INPUT jack on your TV (or AV amplifier).

●

You will enjoy regular quality images.

2. Connect audio cables (white and red) between the
AUDIO OUT jacks on the DVD Recorder and AUDIO
IN jacks on TV (or AV amplifier).

(See pages 21-22)

Connecting & Setting Up

Video/Audio Cable

yellow

yellow

Case 2 : Connecting to an S-Video output jack

1. Connect an S-Video cable (not included) between the
S-VIDEO OUT jack on DVD Recorder and S-VIDEO
INPUT jack on your TV (or AV amplifier).

2. Connect audio cables (white and red) between the
AUDIO OUT jacks on DVD Recorder and AUDIO IN
jacks on TV (or AV amplifier).

●

You will enjoy high quality images.

20

- English

Case 3 : Component Video output jacks

1. Connect Component video cables(not supplied)
between the COMPONENT OUT(Y,P

DVD Recorder and COMPONENT IN(Y,P

on your TV.

2. Connect audio cables (white and red) between the
AUDIO OUT jacks on the DVD Recorder and AUDIO
IN jacks on TV (or AV amplifier).
(See pages 21-22).

3. After connecting, refer to the page 34 to 35.

●

You will enjoy high quality and accurate colour
reproduction images.

green

blue

red

red

B,PR

) jacks on

blue

B,PR

) jacks

green

Other type of connecting the Audio output cable

There are several ways to output audio signal not using
scart cables. Select the audio connection that best suits
you below.

●

Case 1 : Connecting to your TV

●

Case 2 : Connecting to a stereo amplifier with AV

●

Case 3 : Connecting to an AV amplifier with a

Case 1 : Connecting to your TV

If your TV has audio input jacks, use this connection.

output jacks

digital output jack

Manufactured under licence from Dolby
Laboratories. “Dolby” and the double-D symbol
are trademarks of Dolby Laboratories.

“DTS” and “DTS Digital Out” are trademarks of
DTS, Inc.

Connecting & Setting Up

NOTE

■

Make sure that the colour coded
connections match. The Y, P

B

R

, P
component output jacks of your DVD
Recorder must be connected to the exact
corresponding component input jacks on
your TV.

■

Progressive setting is only available when
the Video Out is set to Component.
(See page 34)

yellow

white

red

red

white

yellow

English -

21

Case 2 : Connecting to a stereo amplifier with AV output jacks

If your stereo amplifier only has AUDIO INPUT
jacks(L and R), use the AUDIO OUT jacks.

Case 3: Connecting to an AV amplifier with a digital output jack

If your AV amplifier has a Dolby Digital, MPEG2 or
DTS decoder and a digital input jack, use this
connection. To enjoy Dolby Digital, MPEG2 or DTS
sound, you will need to set up the audio settings.
(See pages 32-33)

Connecting & Setting Up

red

Front(L)
speaker

white

whitered

Front(R)
speaker

Rear(L)

Front(L)

or

Rear(R)

Front(R)

Subwoofer Centre

22

- English

Connecting to AV3 IN, DV
input jack (DVD-R130,
R131 only)

This allows you to connect your DVD Recorder to other
external devices and view or record their outputs.

●

Case 1 : Connecting a VCR, Set-Top Box(STB), DVD

●

Case2 : Connecting a Camcorder to the DV IN jack

Case 1 : Connecting a VCR, Set-Top Box(STB), DVD player or Camcorder to the AV3 IN jacks

Connecting a VCR or external device to AV3 IN jacks of
the DVD Recorder.
You can record from connected equipment (VCR, STB,
DVD player or Camcorder).

player or Camcorder to the AV3 IN jacks

(DVD-R130, R131 only)

Case 2 : Connecting a Camcorder to the DV IN jack (DVD-R130, R131 only)

If your digital camcorder has a DV output jack, connect
it to the DV input jack of your DVD Recorder.

Camcorder

■

If the input is not selected automatically,

NOTE

use INPUT SEL. button to select proper
input.

Connecting & Setting Up

NOTE

Camcorder

VCR

yellow

white

STB

DVD

yellow

white

red

■

AV 3 IN selection will be automatically
done. If the input is not selected
automatically, use INPUT SEL. button to
select proper input.

■

Copy protected content cannot be
recorded.

red

English -

23

System

Setup

On-Screen Menu Navigation

The on-screen menus allow you to enable or disable
various functions on your DVD Recorder.
Use the following buttons to open and navigate through
the on-screen menus.

System Setup

On-Screen Menu Navigation......................24

Plug & Auto Setup......................................25

Setting the Clock ........................................26

Presetting Channels with

the Auto Setup function..............................27

Presetting Channels with

the Manual Setup function .........................28

Setting up the Language Options ..............29

EP Mode Time Setting ...............................30

Automatic Chapter Creation.......................31

Quick Recording Setting ............................32

DivX(R) Registration...................................32

Setting up the Audio Options .....................32

Setting up Video Output Options................34

Setting up the Progressive scan ................35

Canceling the Progressive scan.................35

Setting up the Display(Video) Options .......36

Setting up the Parental Control..................37

DVD-Recorder

No Disc

Programme
Setup

Scheduled Record List

Programme

RETURNOKMOVE EXIT

√√

DVD-Recorder

DVD-RW(VR)

Title List
Playlist
Disc Manager
Programme
Setup

Title List

MENU Button

1

Press this button on the remote control to open the
on-screen MENU.
Press again to exit the on-screen MENU.

…… †† , œœ √√

2

Press these buttons on remote control to move the
selection bar …†, œ√to cycle through the menu
options.

Buttons

OK Button

3

Press this button on the remote control to confirm any
new settings.

RETURN Button

4

Press this button on the remote control to return to the
Previous MENU screen displayed or to exit the
on-screen MENU.

Title List

√√

RETURNOKMOVE EXIT

24

- English

Plug & Auto Setup

Your DVD Recorder will automatically set itself up when
it is plugged in for the first time. TV stations and clock
will be stored in memory. The process takes a few
minutes. Your DVD Recorder will then be ready for use.

Connect the RF cable as indicated on page

1

18.

(Connecting Your DVD Recorder to the TV Using the RF
Cable and scart cable.)

Plug the DVD Recorder into the mains.

2

“Auto” in the front panel display flickers.

Select the language using the …† buttons,

3

then press the OK button.

Français
Deutsch
Español
Italiano
Nederlands

RETURNOKMOVE

Auto Setup

Auto Setup

DVD-Recorder

No Disc

Language Set English

Press the OK button or wait for a few

4

seconds to start the auto setup.

DVD-Recorder

No Disc

Auto setup will be started.

Check antenna and TV cable connection.

•

Refer to following abbreviation table when selecting “Country”.

A(Austria) NL(Netherlands) S(Sweden) PL(Poland)

B(Belgium) I(Italy) CH(Swiss) CZ (Czech)

DK(Denmark) N(Norway) TR(Turkey) Others

FIN(Finland) P(Portugal) GR(Greece)

D(Deutschland) E(Spain) HU(Hungary)

•

The DVD Recorder searches for the stations according to a preset
preference list corresponding to the country that you have selected.

Auto Channel scan will be started.

6

Auto channel memory

Stop

The number of stations automatically stored by the DVD

•

17%

Recorder depends on the number of stations that it has found.

Check the date and time.

7

DVD-Recorder

No Disc

Date Time

JAN 01 2006 12 00 On

SUN

• if it is : Correct, press the OK button then the date and time
will be saved. If you don't press the OK button, the
date and time will be saved automatically after 5
seconds.

• if it is : Incorrect, input correct Time, Date, Year using …†œ √
buttons or number buttons. Press the OK button then
the date and time will be saved. When you need to
change clock setting, you can set up it manually.
(see page 26.)

Auto Setup

Auto Clock

RETURNOKMOVE

System Setup

RETURNOK

Select “Country” using the …†œ √

5

buttons to select your country then press

the OK button.

DVD-Recorder

Country Selection

Autom. Instal.

A

Handmatig Instal.

B
DK
FIN

D E HU

NL

I
N
P

Auto Setup

PL
CZ

Others

√√

√√

S
CH
TR
GR

RETURNOKMOVE

NOTE

■

Now, DVD Recorder is ready for use.
Function for “Plug & Auto Setup” is fixed
already. So if you want to change this fixed
one, you can change it by Presetting the
Stations in OSD “Presetting Channels with
the Manual set up function” menu.
(see page 28)

■

Auto Setup function can be performed by
pressing and holding down the PROG ( )
buttons on the front panel of the DVD Recorder
simultaneously for more than 5 seconds with
no disc in the DVD Recorder.

English -

25

Setting the Clock

Press the …† buttons to select On for the

4

Auto Clock.

This menu is used to set the current time.
You need to set the time to use timer recording.

1

System Setup

2

With the DVD Recorder in Stop mode/No

Disc mode, press the MENU button.

DVD-Recorder

No Disc

Programme
Setup

Scheduled Record List

Programme

√√

RETURNOKMOVE EXIT

Press the …† buttons to select Setup, then
press the OK or √ button.

RETURNOKMOVE EXIT

Setup

√√

√√

√√

√√

√√

√√

√√

DVD-Recorder

No Disc

Programme
Setup

System
Clock Set
Language
Audio
Video
Parental Control
Install

DVD-Recorder

No Disc

Programme
Setup

Date Time

JAN 01 2006 12 00 On

SUN

Clock Set

Auto Clock

RETURNOKMOVE EXIT

Press the OK button, then the date and

5

time will be saved.

If you don’t press the OK button, it will not be saved.

■

You must have the RF cable connected to

NOTE

set the Auto Clock. (See page 18)

■

The DVD Recorder automatically sets the
clock according to the time signal
broadcast between the channels PR1 to
PR5. If you do not need the Auto clock
set function, select Off.

3

26

- English

Press the …† buttons to select Clock Set,
then press the OK or √ button.

Use the …†œ √ buttons to input Time, Date or Year.
Use number buttons to input clock data directly.

DVD-Recorder

No Disc

Programme
Setup

Date Time
JAN 01 2006 12 00 On
SUN

Clock Set

Auto Clock

RETURNOKMOVE EXIT

Presetting Channels with the Auto Setup function

This feature allows you to manually set the DVD
Recorder tuner band to Antenna or Cable, whichever
you connected to the Antenna In jack during initial
setup.

With the DVD Recorder in Stop mode/No

1

Disc mode, press the MENU button.

DVD-Recorder

No Disc

Programme

Scheduled Record List

Setup

Press the …† buttons to select Setup, then

2

press the OK or √ button.

Programme

√√

RETURNOKMOVE EXIT

Press the …† buttons to select Auto

4

Setup, then press the OK or √ button.

The Country Seletion screen is displayed.

S

PL

CH

CZ

TR

Others
GR
HU

RETURNOKMOVE EXIT

Install

√√

√√

DVD-Recorder

No Disc

Programm

A

e

B

Setup

DK
FIN

D

Country Selection

Auto Setup

NL

Manual Setup

I
N
P
E

Press the …†œ √ buttons to select your

5

“Country”, then press the OK button.

• The DVD Recorder searches for the stations
according to a preset preference list corresponding to
the country that you have selected.

Refer to following table when selecting your
country.

A(Austria) NL(Netherlands) S(Sweden) PL(Poland)

B(Belgium) I(Italy) CH(Swiss) CZ (Czech)

DK(Denmark) N(Norway) TR(Turkey) Others

FIN(Finland) P(Portugal) GR(Greece)

D(Deutschland) E(Spain) HU(Hungary)

System Setup

RETURNOKMOVE EXIT

Setup

√√

√√

√√

√√

√√

√√

√√

DVD-Recorder

No Disc

Programme
Setup

System
Clock Set
Language
Audio
Video
Parental Control
Install

Press the …† buttons to select Install, then

3

press the OK or √ button.

RETURNOKMOVE EXIT

Install

√√

√√

DVD-Recorder

No Disc

Programme
Setup

Auto Setup
Manual Setup

Press the OK button to continue.

6

If you want to exit, press the MENU button.

DVD-Recorder

No Disc

Programme

Auto Setup
Manual Setup

Setup

Your data will be lost.

Press [OK] to continue, [MENU] to exit.

RETURNOKMOVE EXIT

Channel scan will be started.

7

Press the OK button to stop the Auto Setup.

Auto channel memory

Stop

Install

√√

√√

17%

English -

27

Presetting Channels with the Manual Setup function

You can add preset channel that Auto Channel Search
missed. And you can delete a channel you wish to
remove. You can programme the order of channels.

Press the …† buttons to select Manual

4

Setup, then press the OK or √ button.

Manual Setup

PR CH Name Decoder Edit

01 --- ---- ---­02 --- ---- ---­03 --- ---- ---­04 --- ---- ---­05 --- ---- ---­06 --- ---- ---­07 --- ---- ----

RETURNOKMOVE EXIT

√√
√√
√√
√√
√√
√√
√√

1

System Setup

2

3

With the DVD Recorder in Stop mode/No

Disc mode, press the MENU button.

DVD-Recorder

No Disc

Programme
Setup

Scheduled Record List

Programme

√√

RETURNOKMOVE EXIT

Press the …† buttons to select Setup, then
press the OK or √ button.

RETURNOKMOVE EXIT

Setup

√√

√√

√√

√√

√√

√√

√√

DVD-Recorder

No Disc

Programme
Setup

System
Clock Set
Language
Audio
Video
Parental Control
Install

Press the …† buttons to select Install, then
press the OK or √ button.

RETURNOKMOVE EXIT

Install

√√

√√

DVD-Recorder

No Disc

Programme
Setup

Auto Setup
Manual Setup

Press the …† buttons to select a PR

5

(programme) you wish to edit, delete, or

swap, then press the OK or √ button.
Select Edit, Delete or Swap using the …†
buttons, then press the OK or √ button.

Manual Setup

PR CH Name Decoder Edit

01 --- ---- ----
02 --- ---- ----
03 --- ---- ----
04 --- ---- ----
05 --- ---- ---­06 --- ---- ---­07 --- ---- ----

• Edit : You can add or edit PR(programme). After
change PR informations(CH, Name, Decoder, MFT),
select Done, then press the OK button.

Manual Setup

Manual Setup

01

PR

√√

œ

1

CH

- - - -

Name

Off

Decoder
MFT

--- --­Done

OKMOVE

- CH : Tune the channel using œ √ buttons.

- Name : Display station name automatically detected in

broadcasting signal. If not detected, you can
edit name by using …†œ √ buttons.

- Decoder : If you set on, you can record scrambled

channels using external decoder box.
Before setting on, refer to connecting
external decoder box in the page 19.

- MFT : You can tune up the channel frequency better

using œ √ buttons.

Edit
Delete
Swap

RETURNOKMOVE EXIT

√√
√√
√√
√√
√√
√√
√√

28

- English

• Delete : the channel information of selected

PR(programme) will be removed.

• Swap : You can swap the channel information of two

PR(programme). For example, if you wish to swap PR2
and PR5, select swap at PR2, then press the OK
button at PR5.

Setting up the Language Options

If you set the audio, subtitle, disc menu, on-screen
menu, DivX subtitle language in advance, they will
come up automatically every time you watch a
movie.
If the selected language is not recorded on the disc,
the original pre-recorded language is selected.

With the DVD Recorder in Stop mode/No

1

Disc mode, press the MENU button.

DVD-Recorder

No Disc

Programme
Setup

Scheduled Record List

Programme

√√

Press the …† buttons to select the desired

4

language option, then press the OK or √

button.

●

Audio : For the speaker sound.

●

Subtitle : For the disc subtitles.

●

Disc Menu : For the disc menu contained on the
disc

●

On-Screen Menu : For the screen of your DVD
Recorder

●

DivX Subtitle: Selecting a supported DivX subtitle
language by region.

Afrikaans, Basque, Catalan, Danish, Dutch,

Western

Central

Greek

Cyrillic

English, Faeroese, Finnish, French, German,
Icelandic, Indonesian, Italian, Malay, Norwegian,
Portuguese, Spanish, Swahili and Swedish

English, Albanian, Croatian, Czech, Hungarian,
Polish, Romanian, Serbian(Latin), Slovak and
Slovenian

English and Greek

English, Azeri, Belarusian, Bulgarian, Kazakh,
Macedonian, Russian, Serbian, Tatar, Ukrainian
and Uzbek

System Setup

RETURNOKMOVE EXIT

Press the …† buttons to select Setup, then

2

press the OK or √ button.

RETURNOKMOVE EXIT

Setup

√√

√√

√√

√√

√√

√√

√√

DVD-Recorder

No Disc

Programme
Setup

System
Clock Set
Language
Audio
Video
Parental Control
Install

Press the …† buttons to select Language,

3

then press the OK or √ button.

Language setup menu will be displayed.

DVD-Recorder

No Disc

Programme
Setup

Audio : Original
Subtitle : Automatic
Disc Menu : English
On-Screen Menu : English
DivX Subtitle : Western

Language

RETURNOKMOVE EXIT

√√

√√

√√

√√

√√

Press the …† buttons to select the desired
language, then press the OK or √ button.

5

Language

Original
English
Français
Deutsch
Español
Italiano
Nederlands
Korean

RETURNOKMOVE EXIT

……

√√

√√

√√

√√

√√

††

NOTE

DVD-Recorder

No Disc

Programme

Audio : Original

Setup

Subtitle : Automatic
Disc Menu : English
On-Screen Menu : English
DivX Subtitle : Western

■

Press the RETURN or œ button to return
to the previous menu.
Press the MENU button to exit the menu.

■

The selected language will only appear if
it is supported on the disc.

■

If the subtitle language is displayed in
broken fonts, change DivX Subtitle to the
appropriate region.
If it still does not work, the format is not
supported.

English -

29

EP Mode Time Setting

Press the …† buttons to select EP Mode

4

Time, then press the OK or √ button.

You can select one of four recording modes by pressing
the REC MODE button repeatedly.
EP mode is one of four REC Mode (XP,SP,LP,EP).
In EP(Extended Play) mode, you can set recording time
to 6 or 8 hours by this setting.

1

System Setup

2

With the DVD Recorder in Stop mode/No

Disc mode, press the MENU button.

DVD-Recorder

No Disc

Programme
Setup

Scheduled Record List

Programme

√√

RETURNOKMOVE EXIT

Press the …† buttons to select Setup, then
press the OK or √ button.

RETURNOKMOVE EXIT

Setup

√√

√√

√√

√√

√√

√√

√√

DVD-Recorder

No Disc

Programme
Setup

System
Clock Set
Language
Audio
Video
Parental Control
Install

DVD-Recorder

No Disc

Programme
Setup

EP Mode Time : 6 Hours
Chapter Creator Off
Quick Recording : Off

System

6 Hours
8 Hours

RETURNOKMOVE EXIT

√√

√√

√√

Press the …† buttons to select the desired

5

time, then press the OK or √ button.

3

30

- English

Press the …† buttons to select System,
then press the OK or √ button.

System menu will be displayed.

DVD-Recorder

No Disc

Programme
Setup

EP Mode Time : 6 Hours
Chapter Creator : Off
Quick Recording : Off

System

RETURNOKMOVE EXIT

√√

√√

√√