Samsung CLP775ND User Manual

Color Laser Printer

User’s Guide

CLP-775 Series

imagine the possibilities

Thank you for purchasing a Samsung product.

copyright

© 2011 Samsung Electronics Co., Ltd. All rights reserved. This user’s guide is provided for information purposes only. All information included herein is subject to change without notice. Samsung Electronics is not responsible for any direct or indirect damages, arising from or related to use of this user’s guide.

• Samsung and Samsung logo are trademarks of Samsung Electronics Co., Ltd.

• PCL and PCL 6 are trademarks of Hewlett-Packard Company.

• Microsoft, Windows, Windows Vista, Windows 7 and Windows 2008 Server R2 are either registered trademarks or trademarks of Microsoft Corporation.

• PostScript 3 is a trademark of Adobe System, Inc.

• UFST® and MicroType™ are registered trademarks of Monotype Imaging Inc.

• TrueType, LaserWriter and Macintosh are trademarks of Apple Computer, Inc.

• All other brand or product names are trademarks of their respective companies or organizations.

• Refer to the 'LICENSE.txt' file in the provided CD-ROM for the open source license information.

REV 1.04

Copyright_ 2

safety information

These warnings and precautions are included to prevent injury to you and others, and to prevent any potential damage to your machine. Be sure to read and understand all of these instructions before using the machine.

Use common sense for operating any electrical appliance and whenever using your machine. Also, follow all warnings and instructions marked on the machine and in the accompanying literature. After reading this section, keep it in a safe place for future reference.

Important safety symbols

This section explains the meanings of all icons and signs in the user's guide. These safety symbols are in order, according to the degree of danger.

Explanation of all icons and signs used in the user’s guide:

Warning Hazards or unsafe practices that may result in severe personal injury or death.

Caution Hazards or unsafe practices that may result in minor personal injury or property damage.

Do not attempt.

Operating environment

Warning

Do not disassemble.

Do not touch.

Unplug the power cord from the wall socket.

Make sure the machine is grounded to prevent electric shock.

Call the service center for help.

Follow directions explicitly.

Do not use if the power cord is damaged or if the electrical outlet is not grounded.

► This could result in electric shock or fire.

Do not place anything on top of the machine (water, small metal or heavy objects, candles, lit cigarettes, etc.).

► This could result in electric shock or fire.

Do not bend, or place heavy objects on the power cord.

► Stepping on or allowing the power cord to be crushed by a heavy object could result in electric shock or fire.

Do not remove the plug by pulling on the cord; do not handle the plug with wet hands.

► This could result in electric shock or fire.

Safety information_ 3

Caution

•If the machine gets overheated, it releases smoke,

makes strange noises, or generates an odd odor, immediately turn off the power switch and unplug the machine.

•The user should be able to access the power outlet

in case of emergencies that might require the user to pull the plug out.

► This could result in electric shock or fire.

Be careful, the paper output area is hot. ► Burns could occur.

If the machine has been dropped, or if the cabinet appears damaged, unplug the machine from all interface connections and request assistance from qualified service personnel.

► Otherwise, this could result in electric shock or fire.

If the machine exhibits a sudden and distinct change in performance, unplug the machine from all interface connections and request assistance from qualified service personnel.

► Otherwise, this could result in electric shock or fire.

Operating method

During an electrical storm or for a period of non-operation, remove the power plug from the electrical outlet.

► This could result in electric shock or fire.

If the plug does not easily enter the electrical outlet, do not attempt to force it in.

► Call an electrician to change the electrical outlet, or this could result in electric shock.

Do not allow pets to chew on the AC power, telephone or PC interface cords.

► This could result in electric shock or fire and/or injury to your pet.

If the machine does not operate properly after these instructions have been followed, unplug the machine from all interface connections and request assistance from qualified service personnel.

► Otherwise, this could result in electric shock or fire.

Caution

Do not forcefully pull the paper out during printing. ► It can cause damage to the machine.

Be careful not to put your hand between the machine and paper tray.

► You may get injured.

Do not block or push objects into the ventilation opening. ► This could result in elevated component temperatures which

can cause damage or fire.

Safety information_ 4

When printing large quantities, the bottom part of the paper output area may get hot. Do not allow children to touch.

► Burns can occur.

When removing jammed paper, do not use tweezers or sharp metal objects.

► It can damage the machine.

Do not allow too many papers to stack up in the paper output tray.

► It can damage the machine.

Be care when replacing paper or removing jammed paper. ► New paper has sharp edges and can cause painful cuts.

Installation / Moving

Warning

Caution

This machine's power interception device is the power cord. ► To switch off the power supply, remove the power cord from

the electrical outlet.

Do not place the machine in an area with dust, humidity or water leaks.

► This could result in electric shock or fire.

Before moving the machine, turn the power off and disconnect all cords. Then lift the machine:

• If the machine weighs under 20 kg (44.09lbs), lift

with 1 person.

• If the machine weighs 20 kg (44.09lbs) - 40kg

(88.18lbslbs), lift with 2 people.

• If the machine weighs more than 40 kg (88.18lbs),

lift with 4 or more people.

► The machine could fall, causing injury or machine damage.

Do not place the machine on an unstable surface. ► The machine could fall, causing injury or machine damage.

The machine should be connected to the power level which is specified on the label.

► If you are unsure and want to check the power level you are using, contact the electrical utility company.

Use only No.26 AWG necessary.

► Otherwise, it can cause damage to the machine.

or larger, telephone line cord, if

Do not put a cover over the machine or place it in an airtight location, such as a closet.

► If the machine is not well-ventilated, this could result in fire.

Make sure you plug the power cord into a grounded electrical outlet.

► Otherwise, this could result in electric shock or fire.

Do not overload wall outlets and extension cords. ► This can diminish performance, and could result in electric

shock or fire.

Use the power cord supplied with your machine for safe operation. If you are using a cord which is longer than 2 meters (6 feet) with a 140V machine, then the gauge should be 16 AWG or larger.

► Otherwise, it can cause damage to the machine, and could result in electric shock or fire.

a. AWG: American Wire Gauge

Safety information_ 5

Maintenance / Checking

Caution

Unplug this product from the wall outlet before cleaning the inside of the machine. Do not clean the machine with benzene, paint thinner or alcohol; do not spray water directly into the machine.

► This could result in electric shock or fire.

When you are working inside the machine replacing supplies or cleaning the inside, do not operate the machine.

► You could get injured.

Keep the power cable and the contact surface of the plug clean from dust or water.

► Otherwise, this could result in electric shock or fire.

Do not remove any covers or guards that are fastened with screws.

•Do not remove any covers or guards that are fastened with

screws.

•Fuser units should only be repaired by a certified service

technician. Repair by non-certified technicians could result in fire or electric shock.

► The machine should only be repaired by a Samsung service technician.

Keep cleaning supplies away from children. ► Children could get hurt.

Do not disassemble, repair or rebuild the machine by yourself.

► It can damage the machine. Call a certified technician when the machine needs repair.

To clean and operate the machine, strictly follow the user's guide provided with the machine.

► Otherwise, you could damage the machine.

Supply usage

Caution

Do not disassemble the toner cartridge. ► Toner dust can be dangerous if inhaled or

ingested.

Do not burn any of the supplies such as toner cartridge or fuser unit.

► This could cause an explosion or uncontrollable fire.

When changing the toner cartridge or removing jammed paper, be careful not to let toner dust touch your body or clothes.

► Toner dust can be dangerous if inhaled or ingested.

When storing supplies such as toner cartridges, keep them away from children.

► Toner dust can be dangerous if inhaled or ingested.

Using recycled supplies, such as toner, can cause damage to the machine.

► In case of damage due to the use of recycled supplies, a service fee will be charged.

When toner gets on your clothing, do not use hot water to wash it.

► Hot water sets toner into fabric. Use cold water.

Safety information_ 6

regulatory information

This machine is designed for our sound environment and certified with several regulatory statements.

Laser safety statement

The printer is certified in the U.S. to conform to the requirements of DHHS 21 CFR, chapter 1 Subchapter J for Class I(1) laser products, and elsewhere is certified as a Class I laser product conforming to the requirements of IEC 60825-1 : 2007.

Class I laser products are not considered to be hazardous. The laser system and printer are designed so there is never any human access to laser radiation above a Class I level during normal operation, user maintenance or prescribed service condition.

Warning

Never operate or service the printer with the protective cover removed from laser/scanner assembly. The reflected beam, although invisible, can damage your eyes.

When using this product, these basic safety precautions should always be followed to reduce risk of fire, electric shock, and injury to persons:

Ozone safety

This product's ozone emission rate is under 0.1 ppm. Because ozone is heavier than air, keep the product in a place with good ventilation.

Regulatory information_ 7

Power saver

Recycling

China only

This printer contains advanced energy conservation technology that reduces power consumption when it is not in active use. When the printer does not receive data for an extended period of time, power consumption is automatically lowered. ENERGY STAR and the ENERGY STAR mark are registered U.S. marks.

For more information on the ENERGY STAR program see http://www.energystar.gov

Recycle or dispose of the packaging material for this product in an environmentally responsible manner.

Correct Disposal of This Product (Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries with separate collection systems)

This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources.

Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take these items for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic accessories should not be mixed with other commercial wastes for disposal.

The United States of America only

Dispose unwanted electronics through an approved recycler. To find the nearest recycling location, go to our website:www.samsung.com/recyclingdirect Or call, (877) 278 - 0799

Regulatory information_ 8

Correct disposal of batteries in this product

(Applicable in the European Union and other European countries with separate battery return systems.)

This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed with other household waste at the end of their working life. Where marked, the chemical symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference levels in EC Directive 2006/66. If batteries are not properly disposed of, these substances can cause harm to human health or the environment. To protect natural resources and to promote material reuse, please separate batteries from other types of waste and recycle them through your local, free battery return system.

Radio Frequency Emissions

FCC Information to the User

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

• This device may not cause harmful interference, and

• This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or experienced radio TV technician for help.

Change or modifications not expressly approved by the manufacturer responsible for compliance could void the user's authority to operate the equipment.

Canadian Radio Interference Regulations

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled “Digital Apparatus”, ICES-003 of the Industry and Science Canada.

Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux appareils numériques de Classe A prescrites dans la norme sur le matériel brouilleur: “Appareils Numériques”, ICES-003 édictée par l’Industrie et Sciences Canada.

RFID (Radio Frequenty Interface Device)

RFID operation is subject to the following two conditions:(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. (U.S.A., France, Taiwan only)

Regulatory information_ 9

Taiwan only

Russia only

Turkey only

Replacing the Fitted Plug (for UK Only)

Important

The mains lead for this machine is fitted with a standard (BS 1363) 13 amp plug and has a 13 amp fuse. When you change or examine the fuse, you must re-fit the correct 13 amp fuse. You then need to replace the fuse cover. If you have lost the fuse cover, do not use the plug until you have another fuse cover.

The 13 amp plug is the most widely used type in the UK and should be suitable. However, some buildings (mainly old ones) do not have normal 13 amp plug sockets. You need to buy a suitable plug adaptor. Do not remove the moulded plug.

If you cut off the moulded plug, get rid of it straight away.

You cannot rewire the plug and you may receive an electric shock if you plug it into a socket.

Regulatory information_ 10

Important warning:

You must earth this machine. The wires in the mains lead have the following color code:

• Green and Yellow: Earth

• Blue: Neutral

• Brown: Live

If the wires in the mains lead do not match the colors marked in your plug, do the following: You must connect the green and yellow wire to the pin marked by the letter “E” or by the safety ‘Earth symbol’ or colored green and yellow or

green. You must connect the blue wire to the pin which is marked with the letter “N” or colored black. You must connect the brown wire to the pin which is marked with the letter “L” or colored red. You must have a 13 amp fuse in the plug, adaptor, or at the distribution board.

Declaration of Conformity (European Countries)

Approvals and Certifications

Hereby, Samsung Electronics, declares that this [CLP-775 Series] is in compliance with the essential requirements and other relevant provisions of R&TTE Directive (1999/5/EC).

The declaration of conformity may be consulted at www.samsung.com/printer, go to Support > Download center and enter your printer (MFP) name to browse the EuDoC.

January 1, 1995: Council Directive 2006/95/EC Approximation of the laws of the member states related to low voltage equipment. January 1, 1996: Council Directive 2004/108/EC, approximation of the laws of the Member States related to electromagnetic compatibility. March 9, 1999: Council Directive 1999/5/EC on radio equipment and telecommunications terminal equipment and the mutual recognition of

their conformity. A full declaration, defining the relevant Directives and referenced standards can be obtained from your Samsung Electronics Co., Ltd. representative.

European radio approval information (for products fitted with EU-approved radio devices)

Low power, Radio LAN type devices (radio frequency (RF) wireless communication devices), operating in the 2.4 GHz/5 GHz band, may be present (embedded) in your printer system which is intended for home or office use. This section is only applicable if these devices are present. Refer to the system label to verify the presence of wireless devices.

Wireless devices that may be in your system are only qualified for use in the European Union or associated areas if a CE mark with a Notified Body Registration Number and the Alert Symbol is on the system label.

The power output of the wireless device or devices that may be embedded in you printer is well below the RF exposure limits as set by the European Commission through the R&TTE directive.

European states qualified under wireless approvals:

EU countries

European states with restrictions on use:

EU In France, the frequency range is restricted to 2454-2483.5 MHz for devices above 10 mW transmitting power such as wireless EEA/EFTA countries No limitations at this time

Regulatory information_ 11

Regulatory Compliance Statements

Wireless Guidance

Low power, Radio LAN type devices (radio frequency (RF) wireless communication devices), operating in the 2.4 GHz/5 GHz Band, may be present (embedded) in your printer system. The following section is a general overview of considerations while operating a wireless device.

Additional limitations, cautions, and concerns for specific countries are listed in the specific country sections (or country group sections). The wireless devices in your system are only qualified for use in the countries identified by the Radio Approval Marks on the system rating label. If the country you will be using the wireless device in, is not listed, contact your local Radio Approval agency for requirements. Wireless devices are closely regulated and use may not be allowed.

The power output of the wireless device or devices that may be embedded in your printer is well below the RF exposure limits as known at this time. Because the wireless devices (which may be embedded into your printer) emit less energy than is allowed in radio frequency safety standards and recommendations, manufacturer believes these devices are safe for use. Regardless of the power levels, care should be taken to minimize human contact during normal operation.

As a general guideline, a separation of 20 cm (8 inches) between the wireless device and the body, for use of a wireless device near the body (this does not include extremities) is typical. This device should be used more than 20 cm (8 inches) from the body when wireless devices are on and transmitting.

This transmitter must not be collocated or operation in conjunction with any other antenna or transmitter. Some circumstances require restrictions on wireless devices. Examples of common restrictions are listed below:

Radio frequency wireless communication can interfere with equipment on commercial aircraft. Current aviation regulations require wireless devices to be turned off while traveling in an airplane. IEEE 802.11 (also known as wireless Ethernet) and Bluetooth communication devices are examples of devices that provide wireless communication.

In environments where the risk of interference to other devices or services is harmful or perceived as harmful, the option to use a wireless device may be restricted or eliminated. Airports, Hospitals, and Oxygen or flammable gas laden atmospheres are limited examples where use of wireless devices may be restricted or eliminated. When in environments where you are uncertain of the sanction to use wireless devices, ask the applicable authority for authorization prior to use or turning on the wireless device.

Every country has different restrictions on the use of wireless devices. Since your system is equipped with a wireless device, when traveling between countries with your system, check with the local Radio Approval authorities prior to any move or trip for any restrictions on the use of a wireless device in the destination country.

If your system came equipped with an internal embedded wireless device, do not operate the wireless device unless all covers and shields are in place and the system is fully assembled.

Wireless devices are not user serviceable. Do not modify them in any way. Modification to a wireless device will void the authorization to use it. Contact manufacturer for service.

Only use drivers approved for the country in which the device will be used. See the manufacturer System Restoration Kit, or contact manufacturer Technical Support for additional information.

Israel only

Regulatory information_ 12

China only

Regulatory information_ 13

about this user’s guide

This user’s guide provides information about basic understanding of the machine as well as detailed explanation on each step during actual usage. Valuable for both novice and professional users can refer to this as a guide for installing and using the machine.

• Read the safety information before using the machine.

• If you have a problem using the machine, refer to the troubleshooting chapter. (See "Troubleshooting" on page 68.)

• Terms used in this user’s guide are explained in the glossary chapter. (See "Glossary" on page 96.)

• Use Index to find information.

• All illustrations in this user’s guide may differ from your machine depending on its options or models.

• The procedures in this user’s guide are mainly based on Windows 7.

Convention

Some terms in this guide are used interchangeably, as below:

• Document is synonymous with original.

• Paper is synonymous with media, or print media.

• Machine refers to printer or MFP.

The following table offers the conventions of this guide:

Convention Description Example

Bold For texts on the display or button names on the machine. Start

Note Provides additional information or detailed specification of the machine function

and feature.

Caution Gives users information to protect the machine from possible mechanical

damage or malfunction.

Footnote Provides additional more detailed information on certain words or a phrase. a. pages per minute

(“Cross-reference”) Guides users to a reference page for the additional detailed information. (See "Finding more information" on

The date format may differ from country to country.

Do not touch the green underside of the toner cartridge.

page 15.)

About this user’s guide_ 14

Finding more information

You can find information for setting up and using your machine from the following resources, either as a print-out or on screen.

Material name Description

Quick Installation Guide

Online User’s Guide This guide provides you with step-by-step instructions for using your machine’s full features, and contains information for maintaining

Network Website You can set the network environment from your computer using network-managing programs, such as SetIP, SyncThru™ Web Admin

Machine Driver Help This help provides you with help information on printer driver and instructions for setting up the options for printing. (See "Using help"

Samsung website If you have Internet access, you can get help, support, machine drivers, manuals, and order information from the Samsung website,

This guide provides information on setting up your machine and this requires that you follow the instructions in the guide to prepare the machine.

your machine, troubleshooting, and installing accessories.

Service, Samsung AnyWeb Print etc. SyncThru™ Web Admin Service will be convenient for network administrators who need to manage many machines simultaneously. Samsung AnyWeb Print helps personal users to screen-capture the website screen in

Windows Internet Explorer easily. You can download the SyncThruTM Web Admin Service or Samsung AnyWeb Print on http://solution.samsungprinter.com. SetIP program is provided in the software CD.

on page 53.)

www.samsungprinter.com.

About this user’s guide_ 15

features of your new product

Your new machine is equipped with a number of special features that improve the quality of the documents you print.

Special Features

Print with excellent quality and speed

• You can print with a resolution of up to 9600x600 dpi

effective output.

• Your machine prints A4-sized paper at up to 33 ppm and

letter-sized paper at up to 35 ppm.

• For duplex printing, your machine prints A4-sized paper at

up to 15 ipm and letter-sized paper at up to 16 ipm.

Handle many different types of printable material

• The multi-purpose tray supports letterhead, envelopes,

labels, custom-sized media, postcards, and heavy paper. The multi-purpose tray holds up to 100 sheets of plain paper.

• The 500-sheet tray 1 and 500-sheet optional trays support

plain paper in various sizes. You can install up to 2 additional trays.

Create professional documents (See "Using advanced print features" on page 49.)

• Print Watermarks. You can customize your documents with

words, such as “Confidential”.

• Print Posters. The text and pictures of each page of your

document are magnified and printed across the sheet of paper and can then be taped together to form a poster.

• You can use preprinted forms and letterhead with plain

paper.

Print in various environments

• You can print with Windows operating systems as well as

Linux, Macintosh and UNIX systems.

• Your machine is equipped with a USB interface and a

network interface.

Save time and money (See "Using advanced print features" on page 49.)

• To save paper, you can print multiple pages on one single

sheet of paper.

• This machine automatically conserves electricity by

substantially reducing power consumption when not in use.

• To save paper, you can print on both sides of the paper

(double-sided printing).

Expand your machine’s capacity

• This machine has an extra memory slot for adding more

memory. (See "Available supplies" on page 83.)

Features of your new product_ 16

Features by Model

The machine is designed to support all of your document needs from printing to more advanced networking solutions for your business. Features by model include:

Features CLP-775 Series

USB 2.0 ●

Hard Disk ○

Network Interface 802.11 b/g/n wireless LAN

Network Interface Ethernet 10/100/1000 Base TX wired LAN ●

Duplex (2-sided) printing ●

IEEE1284 Parallel Connector

Memory module ○

a.Depending on your country, wireless LAN cards may not be available. Contact your local Samsung dealer or the retailer where you

bought your printer

b.If you use the parallel port, you cannot use the USB cable.

( ●: Included, ○: Optional)

○

Features of your new product_ 17

1.introduction

These are the main components of your machine:

This chapter includes:

• Machine overview

• Control panel overview

Machine overview

Front view

• Understanding the control panel

• Turning on the machine

Output tray

Output support

Paper level indicator

Optional tray

Tray 1

Multi-purpose tray

Multi-purpose tray handle

a.This is an optional feature.

Front cover handle

Front cover

Control panel

Paper width guides on a

multi-purpose tray

Toner cartridge

Paper transfer belt

Introduction_ 18

Rear view

Control board cover

Power receptacle

Power-switch

Handle

IEEE1284 Parallel

Connector

Network port

USB port

External device interface (EDI)

IEEE 802.11 b/g/n Wireless

LAN

a.External device interface for Samsung and third party solutions.

b.This is an optional feature.

Introduction_ 19

Control panel overview

Display

Toner colors

Arrow

(Menu)

(Back)

(Stop)

(Power)

(Status LED)

Shows the current status and prompts during an operation.

Show the status of each toner cartridge. (See "Understanding the control panel" on page 21.)

Enters menu mode and scrolls through the available menus. (See "Accessing the Menu" on page 56.)

Sends you back to the upper menu level.

Scroll through the options available in the selected menu, and increase or decrease values.

Confirms the selection on the screen.

Stops an operation at any time. The pop-up window appears on the screen showing the current job that the user can stop or resume.

You can also turn the power on and off with this button. (See "Buttons" on page 21.)

Shows the status of your machine. (See "Understanding the control panel" on page 21.)

Introduction_ 20

Understanding the control panel

Status LED

The color of the status LED indicates the machine's current status.

Status Description

Off • The machine is off-line.

• The machine is in power saver mode. When

data is received, or any button is pressed, it switches to on-line automatically.

Green Blinking • When the LED blinks slowly, the machine is

receiving data from the computer.

• When the LED blinks rapidly, the machine is

printing data.

On The machine is on-line and can be used.

Red Blinking • A minor error has occurred and the machine is

waiting for the error to be cleared. Check the display message. When the problem is cleared, the machine resumes.

• Small amount of toner is left in the cartridge.

The estimated cartridge life Prepare a new cartridge for replacement. You may temporarily increase the printing quality by redistributing the toner. (See "Redistributing toner" on page 68.)

On • A toner cartridge has almost reached its

estimated cartridge life replace the toner cartridge. (See "Replacing the toner cartridge" on page 84.)

• A paper jam has occurred. (See "Clearing

paper jams" on page 69.)

• The cover is opened. Close the cover.

• There is no paper in the tray. Load paper in

the tray.

• The machine has stopped due to a major

error. Check the display message. (See "Understanding display messages" on page 73.)

of toner is close.

. It is recommended to

Buttons

(Menu button)

When you want to know the machine status and set your machine to use an a

dvanced feature press

(menu button). (See "Accessing the Menu" on

page 56.)

(Stop button)

By pressing the

(stop button), you can:

Function Description

Cancel print job

Press (stop button) during printing.

(Power button)

When you want to turn the power off, press this button until to turn the power off. This button can also be used to turn the machine on.

Status Description

Off • The machine is in ready mode.

• The machine’s power is off.

On The machine is in power save mode.

Turning on the machine

1. Plug in the power cord.

2. T

urn the power-switch on.

If you want to turn the power off, press this button until to turn the power off.

a.Estimated cartridge life means the expected or estimated toner

cartridge life, which indicates the average capacity of print-outs and is designed pursuant to ISO/IEC 19798. The number of pages may be affected by operating environment, printing interval, media type, and media size. Some amount of toner may remain in the cartridge even when red LED is on and the printer stops printing.

Check the message on the display. Follow the instructions in the message or refer to troubleshooting part. (See "Understanding display messages" on page 73.). If the problem persists, call for service.

Introduction_ 21

2.getting started

This chapter gives you step-by-step instructions for setting up the USB connected machine and software.

This chapter includes:

• Setting up the hardware

• Supplied software

• System requirements

• Installing the driver locally

Setting up the hardware

This section shows the steps to set up the hardware, as is explained in the Quick Install Guide. Make sure you read the Quick Install Guide first and follow the steps below:

1. Select a stable location.

Select a level, stable place with adequate space for air circulation. Allow extra space to open covers and trays.

The area should be well ventilated and away from direct sunlight or sources of heat, cold, and humidity. Do not set the machine close to the edge of your desk or table.

Printing is suitable for altitudes under 1,000 m (3,281 ft). Refer to the altitude setting to optimize your printing. (See page 40.)

Place the machine on a flat, stable surface so that there is no incline greater than 2 mm (0.08 inch). Otherwise, printing quality may be affected.

2. Unpack the machine and check all the enclosed items.

3. Remove tape holding the machine securely.

4. Install the toner cartridge.

5. Load paper. (See "Loading paper in the tray" on page 43.)

6. Make sure that all cables are connected to the machine.

7. Turn the machine on.

"Altitude adjustment" on

This equipment will be inoperable when mains power fails.

Supplied software

After you have set up your machine and connected it to your computer, you must install the printer software. If you are a Windows or Macintosh OS, install the software from the supplied CD and if you are a Linux OS user or UNIX OS user, download the software from the Samsung website (www.samsung.com/printer) and install.

Machine software are occasionally updated due to release of new operating system and etc. If needed, download the latest version from the Samsung website. (www.samsung.com/printer)

OS Contents

Windows • Printer driver: Use this driver to take full advantage

of your machine’s features.

• PostScript printer driver: Use the PostScript driver

to print documents with complex fonts and graphics in the PS language. (PostScript printer description file is included.)

• Samsung Easy Printer Manager: Samsung Easy

Printer Manager combines device settings as well as printing environments, settings/actions and

launching. All of these features provide a gateway to

conveniently use your Samsung machine.

• Samsung Printing Status: This program allows

you to monitor the machine’s status and alerts you when an error occurs during printing.

• Direct Printing Utility: This program allows you to

print PDF files directly.

• SetIP: Use this program to set your machine’s

TCP/IP addresses.

Macintosh • PostScript printer driver: Use this driver to run

your machine from a Macintosh computer and print documents. (PostScript printer description file is included.)

• Smart Panel: This program allows you to monitor

the machine’s status and alerts you when an error occurs during printing.

• SetIP: Use this program to set your machine’s

TCP/IP addresses.

Getting started_ 22

OS Contents

Macintosh

Linux • Unified Linux Driver: Use this driver to take full

advantage of your machine’s features.

• Printer Description (PPD) file: Use this file to run

your machine from a Linux computer and print documents.

• Smart Panel: This program allows you to monitor

the machine’s status and alerts you when an error occurs during printing.

• SetIP: Use this program to set your machine’s

TCP/IP addresses.

UNIX • UNIX PrinterDriver: Use this driver to print

documents from the UNIX system.

System requirements

Microsoft® Windows

Operating

system

Windows® 2000

Windows® XP Intel® Pentium® III 933

Windows

Server

2003

Windows

Server

2008

Windows

Vista

Windows® 7 Intel® Pentium® IV 1 GHz

Windows Server® 2008 R2

Intel® Pentium® II 400 MHz (Pentium III 933 MHz)

MHz (Pentium IV 1 GHz)

Intel MHz (Pentium IV 1 GHz)

Intel (Pentium IV 2 GHz)

Intel® Pentium® IV 3 GHz

32-bit or 64-bit processor or higher

• Support for DirectX® 9 graphics with 128 MB memory

• DVD-R/W Drive

Intel® Pentium® IV 1 GHz (x86) or 1.4 GHz (x64) processors (2 GHz or faster)

Requirement (recommended)

CPU RAM

Pentium® III 933

Pentium® IV 1 GHz

(to enable the Aero theme).

free HDD

space

64 MB (128

600 MB

MB)

128 MB (256

1.5 GB

MB)

128 MB (512 MB)

512 MB (2

1.25 GB to 2 GB

10 GB

GB)

512 MB (1

15 GB

GB)

1 GB (2 GB) 16 GB

512 MB (2

10 GB

GB)

Requirements (Recommended)

Operating

system

Mac OS X 10.3 ~

10.4

• Intel

• PowerPC G4/ G5

CPU RAM

processors

• 128 MB for a

powerPC based Mac (512 MB)

• 512 MB for an

Intel-based Mac (1 GB)

Mac OS X 10.5

• Intel

processors

512 MB (1 GB) 1 GB

• 867 MHz or faster

Power PC G4/ G5

Mac OS X 10.6

• Intel

processors

1 GB (2 GB) 1 GB

Linux

Items Requirements

Operating system

RedHat Fedora 5, 6, 7, 8, 9, 10, 11, 12, 13 (32/ 64 bit)

Enterprise Linux WS 4, 5 (32/64 bit)

SuSE Linux 10.1 (32 bit) OpenSuSE® 10.2, 10.3, 11.0, 11.1, 11.2 (32/64 bit) Mandriva 2007, 2008, 2009, 2009.1, 2010 (32/64 bit) Ubuntu 6.06, 6.10, 7.04, 7.10, 8.04, 8.10, 9.04, 9.10,

10.04 (32/64 bit) SuSE Linux Enterprise Desktop 10, 11 (32/64 bit) Debian 4.0, 5.0 (32/64 bit)

CPU Pentium IV 2.4GHz (Intel Core™2)

RAM 512 MB (1 GB)

Free HDD space 1 GB (2 GB)

Unix

Items Requirements

Operating system

Free HDD space Up to 100 MB

Sun Solaris 9, 10 (x86, SPARC) HP-UX 11.0, 11i v1, 11i v2, 11i v3 (PA-RISC,

Itanium) IBM AIX 5.1, 5.2, 5,3, 5.4

Free HDD

space

1 GB

• Internet Explorer 6.0 or higher is the minimum requirement for all

Windows operating systems.

• Users who have administrator rights can install the software.

• Windows Terminal Services is compatible with your machine.

• For Windows 2000, Services Pack 4 or higher is required.

Installing the driver locally

A locally connected machine is a machine directly attached to your computer using the cable. If your machine is attached to a network, skip the following steps below and go on to installing a network connected machine’s driver. (See "Installing wired network connected machine’s driver" on page 28.)

Getting started_ 23

• If you are a Macintosh, Linux, or Unix OS user, refer to the

Advanced guide.

• Selecting Advanced Installation > Custom Installation allows

you to choose which programs to install.

• Only use a USB cable no longer than 3 meters (118 inches ).

Windows

1. Make sure that the machine is connected to your computer and powered

on.

If the “Found New Hardware Wizard” appears during the installation procedure, click Cancel to close the window.

2. Insert the supplied software CD into your CD-ROM drive.

The software CD should automatically run and an installation window will appear.

3. Select Install Now.

4. Read License Agreement and select I accept the terms of License Agreement Then, click Next

5. Follow the instructions in the installation window.

If the printer driver does not work properly, follow the steps below to uninstall and reinstall the driver.

a) Make sure that the machine is connected to your computer and

powered on.

b) From the Start menu, select Programs or All Programs >

Samsung Printers > your printer driver name > Uninstall.

c) Select the necessary option and follow the instructions in the

window.

d) After uninstalling the printer driver, reinstall it (see "Installing the

driver locally" on page 23, "Installing wired network connected machine’s driver" on page 28).

Macintosh

1. Make sure that the machine is connected to your computer and powered

on.

2. Insert the supplied software CD into your CD-ROM drive.

3. Double-click the CD-ROM icon that appears on your Macintosh desktop.

4. Double-click the MAC_Installer folder.

5. Double-click the Installer OS X icon.

6. Enter the password and click OK.

7. The Samsung Installer window opens. Click Continue.

8. Read the license agreement and click Continue.

9. Click Agree to agree to the license agreement.

10. Select Easy Install and click Install. Easy Install is recommended for

most users. All components necessary for machine operations will be installed.

If you select Custom Install, you can choose individual components to

install.

11. When the message which warns that all applications will close on your computer appears, click Continue.

12. Select Typical installation for a local printer and then click OK.

If you select Typical installation for a network printer during the machine driver installation, the SetIP program automatically runs. If the machine has already configured network information, close the SetIP program. Go to the next step.

13. After the installation is finished, click Quit.

14. Open the Applications folder > Utilities > Print Setup Utility.

• For Mac OS X 10.5~10.6, open the Applications folder > System

Preferences and click Print & Fax.

15. Click Add on the Printer List.

• For Mac OS X 10.5~10.6, click the “+” icon; a display window will pop

up.

16. For Mac OS X 10.3, select the USB tab.

• For Mac OS X10.4, click Default Browser and find the USB

connection.

• For Mac OS X 10.5~10.6, click Default and find the USB connection.

17. For Mac OS X 10.3, if Auto Select does not work properly, select Samsung in Printer Model and your machine name in Model Name.

• For Mac OS X 10.4, if Auto Select does not work properly, select

Samsung in Print Using and your machine name in Model.

• For Mac OS X 10.5~10.6, if Auto Select does not work properly,

select Select a driver to use... and your machine name in Print Using.

Your machine appears on the Printer List, and is set as the default machine.

18. Click Add.

If the printer driver does not work properly, uninstall the driver and reinstall it.

Follow steps below to uninstall the driver for Macintosh.

a) Make sure that the machine is connected to your computer and

powered on.

b) Insert the supplied software CD into your CD-ROM drive. c) Double-click CD-ROM icon that appears on your Macintosh

desktop.

d) Double-click the MAC_Installer folder. e) Double-click the Installer OS X icon. f) Enter the password and click OK. g) The Samsung Installer window opens. Click Continue. h) Select Uninstall and click Uninstall. i) When the message which warns that all applications will close on

your computer appears, Click Continue.

j) When the uninstall is done, click Quit.

Linux

You need to download the Linux software package from the Samsung website to install the printer software.

Follow the steps below to install the software.

Installing the Linux Unified Driver

1. Make sure that the machine is connected to your computer and

powered on.

2. When the Administrator Login window appears, type in root in the Login field and enter the system password.

Getting started_ 24

You must log in as a super user (root) to install the machine software. If you are not a super user, ask your system administrator.

3. From the Samsung website, download the Unified Linux Driver

package to your computer.

4. Right click the Unified Linux Driver package and extract the

package.

5. Double click cdroot > autorun.

6. When the welcome screen appears, click Next.

7. When the installation is complete, click Finish.

The installation program has added the Unified Driver Configurator desktop icon and the Unified Driver group to the system menu for your convenience. If you have any difficulties, consult the on screen help that is available through your system menu or can otherwise be called from the driver package Windows applications, such as Unified Driver Configurator or Image Manager.

If the printer driver does not work properly, uninstall the driver and reinstall it again.

Follow the steps below to uninstall the driver for Linux.

a) Make sure that the machine is connected to your computer and

powered on.

b) When the Administrator Login window appears, type in “root”

in the Login field and enter the system password. You must log in as a super user (root) to uninstall the printer

driver. If you are not a super user, ask your system administrator.

c) Click the icon at the bottom of the desktop. When the Terminal

screen appears, type in: [root@localhost root]#cd /opt/Samsung/mfp/uninstall/ [root@localhost uninstall]#./uninstall.sh

d) Click Uninstall. e) Click Next. f) Click Finish.

Installing the SmartPanel

1. Make sure that the machine is connected to your computer and

powered on.

2. When the Administrator Login window appears, type in root in the Login field and enter the system password.

You must log in as a super user (root) to install the machine software. If you are not a super user, ask your system administrator.

3. From the Samsung website, download the Smart Panel package to your computer.

4. Right click the Smart Panel package and extract the package.

5. Double click cdroot > Linux > smartpanel > install.sh.

Installing the Printer Settings Utility

1. Make sure that the machine is connected to your computer and

powered on.

2. When the Administrator Login window appears, type in root in the Login field and enter the system password.

You must log in as a super user (root) to install the machine software. If you are not a super user, ask your system administrator.

3. From the Samsung website, download the Printer Setting Utility package to your computer.

4. Right click the Printer Settings Utility package and extract the package.

5. Double click cdroot > Linux > psu > install.sh.

Getting started_ 25

3.network setup

This chapter gives you step-by-step instructions for setting up the network connected machine and software.

This chapter includes:

• Network environment

• Introducing useful network programs

• Using a wired network

• If you are using wired network environment, see "Using a wired

network" on page 26.

• If you are using wireless network environment, see "Wireless

network setup" on page 32.

Network environment

You need to set up the network protocols on the machine to use it as your network machine. You can set up the basic network settings through the machine's control panel.

The following table shows the network environments supported by the machine:

Item Requirements

Network interface • Ethernet 10/100/1000 Base-TX

• 802.11 b/g/n Wireless LAN (Optional)

Network operating system • Windows

Network protocols • TCP/IPv4

Wireless Security • Authentication : Open System, Shared

2000/XP/2003/2008/Vista/7/2008 Server R2

• Various Linux OS

• Mac OS X 10.3 ~ 10.6

• UNIX

• DHCP, BOOTP

• DNS, WINS, Bonjour, SLP, UPnP

• Standard TCP/IP Printing(RAW), LPR,

IPP

• SNMPv 1/2/3, HTTP(S), Telnet, SMTP,

IPSec

• TCP/IPv6 (DHCP, DNS, RAW, LPR,

SNMPv 1/2/3, HTTP(S), IPSec (See "IPv6 configuration" on page 39.)

Key, WPA Personal, WPA2 Personal (PSK), WPA Enterprise, WPA2 Enterprise

• Encryption : WEP64, WEP128, TKIP,

AES

• Wireless network setup

• IPv6 configuration

Introducing useful network programs

There are several programs available to setup the network settings easily in network environment. For the network administrator especially, managing several machines on the network is possible.

Before using the programs below, set the IP adress first.

SyncThru™ Web Service

Web server embedded on your network machine, which allows you to:

• Configure the network parameters necessary for the machine to connect

to various network environments.

• Customize machine settings.

(See "Using SyncThru™ Web Service" on page 60.)

SyncThru™ Web Admin Service

Web-based machine management solution for network administrators. SyncThru™ Web Admin Service provides you with an efficient way of managing network devices and lets you remotely monitor and troubleshoot network machines from any site with corporate internet access. Download this program from http://solution.samsungprinter.com.

SetIP

This utility program allows you to select a network interface and manually configure the IP addresses for use with the TCP/IP protocol. (See IP address" on page 27)

TCP/IPv6 is not supported by this program.

Using a wired network

You must set up the network protocols on your machine to use it on your network. This chapter will show you how this is easily accomplished.

You can use network after connecting network cable to a corresponding port on your machine.

"Setting

Printing Network Configuration report

You can print a Network Configuration Report from the machine’s control panel that will show the current machine’s network settings. This will help you to set up a network and troubleshooting problems.

Network setup_ 26

1. Press on the control panel.

2. Press up/down arrow to highlight Network and press OK.

3. Pre

ss up/down arrow to highlight Network Configuration and press

OK.

Using this Network Configuration Report, you can find your machine MAC address and IP address.

For example:

• MAC

Address : 00:15:99:41:A2:78

• IP Address : 192.0.0.192

Setting IP address

First, you have to set up an IP address for network printing and managements. In most cases a new IP address will be automatically assigned by a DHCP (Dynamic Host Configuration Protocol) server located on the network.

IP setting using control panel

1. Connect your machine to the network with a network cable.

2. Tu

rned on the machine.

3. Press

4. Press u

5. Press u

6. Press u

7. Press u

8. Th

• Enter a numbe

9. Use the up/do

move between digits. When you finish entering the IP address, press

OK.

10. Enter othe press OK.

11. After entering all parameters, press to return to ready mode.

Now go to "Installing wired network connected machine’s driver" on page 28.

IPv4 configuration using SetIP (Windows)

Before using the SetIP program, disable the computer firewall from

Control Panel > Security Center > Windows Firewall.

1. Install this program from the supplied CD-ROM by double-click Application > SetIP > Setup.exe.

2. Follow the instructions in the installation window.

3. Con

4. Tu

5. Fro Printers > SetIP > SetIP.

6. Click the icon (third from left) in the SetIP window to open the

TCP/IP configuration window.

on the control panel.

p/down arrow to highlight Network and press OK. p/down arrow to highlight TCP/IP (IPv4) and press OK. p/down arrow to highlight Set IP Address and press OK. p/down arrow to highlight Manual and press OK.

e first available menu item, IP Address displays.

r between 0 and 255.

wn arrow to enter digits and use the left/right arrow to

r parameters, such as the Subnet Mask or Gateway, and

nect your machine to the network with a network cable.

rn on the machine.

m the Windows Start menu, select All Programs > Samsung

7. Enter the machine’s new information into the configuration window

as follows. In a corporate intranet, you may need to have this information assigned by a network manager before proceeding.

Find the machine’s MAC address from the Network Configuration Report (see "Printing Network Configuration report" on page 26) and enter it without the colons. For example, 00:15:99:29:51:A8 becomes 0015992951A8.

8. Click Apply, and then click OK. The machine will automatically print the Network Configuration Report. Confirm that all the settings are correct.

IPv4 configuration using SetIP (Macintosh)

Before using the SetIP program, disable the computer firewall from System Preferences > Security > Firewall.

The following instructions may vary from your model.

1. Conn

2. In

3. Doub

4. Click the icon (third from left) in the SetIP window to open the

5. Enter the machine’s new information into the configuration window.

6. Select Apply, then OK, and OK again.

7. Qui

ect your machine to the network with a network cable.

sert the Installation CD-ROM, and open the disk window, select

MAC_Installer > MAC_Printer > SetIP > SetIPapplet.html.

le-click the file and Safari will automatically open, then select

Trust. The browser will open the SetIPapplet.html page that shows the printer’s name and IP address information.

TCP/IP configuration window.

In a corporate intranet, you may need to have this information assigned by a network manager before proceeding.

t Safari.

Network setup_ 27

IPv4 configuation using SetIP (Linux)

Before using the SetIP program, disable the computer firewall from System Preferences or Administrator.

The following instructions may vary from your model or operating systems.

1. Open /opt/Samsung/mfp/share/utils/.

2. Dou

3. Cli

4. Enter

ble-click the SetIPApplet.html file.

ck to open the TCP/IP configuration window.

the machine’s new information into the configuration window. In a corporate intranet, you may need to have this information assigned by a network manager before proceeding.

Find the machine’s MAC address from the Network Configuration Report (see "Printing Network Configuration report" on page 26) and enter it without the colons. For example, 00:15:99:29:51:A8

e machine will automatically print the Network Configuration

5. Th

becomes 0015992951A8.

Report.

Network parameter setting

You can also set up the various network settings through the network administration programs such as SyncThru™ Web Admin Service and

SyncThru™ Web Service.

Restoring factory default settings

You may need to reset the machine to the factory default settings when machine that you are using is connected to new network environment.

Restoring factory default settings using control panel

1. Press on the control panel.

2. Press u

3. Press u

4. Tu

p/down arrow to highlight Network and press OK. p/down arrow to highlight Clear Settings and press OK.

rn off and restart machine to apply settings.

Restoring factory default settings using SyncThru™ Web Service

1. Start a web browser such as Internet Explorer, Safari or Firefox and

enter your machine’s new IP address in the browser window. For example,

2. Click Go to access the SyncThru™ Web Service.

3. Cli

ck Login on the upper right of the SyncThru™ Web Service

website. A log-in page appears.

4. Typ

e in the ID and Password then click Login .

If it’s your first time logging into Syn below default ID and password.

• ID: admin

• Password: sec00000

5. Wh

en the SyncThru™ Web Service window opens, click Settings

> Network Settings > Restore Default.

6. Cli

ck Clear for network.

7. Tu

rn off and restart machine to apply settings.

cThru™ Web Service, type in the

Installing wired network connected machine’s driver

You must install the printer driver software for printing. The software includes drivers, applications, and other user friendly programs.

Make sure that the network setup for your machine is completed. All applications should be closed on your computer before beginning installation.

Windows

1. Make sure that the machine is connected to the network and

powered on. Also, your machine’s IP address should have been set.

If the “Found New Hardware Wizard” appears during the installation procedure, click Cancel to close the window.

sert the supplied software CD into your CD-ROM drive.

2. In

The software CD should automatically run and an installation window will

appear.

3. Select Install Now.

When you click the Advanced Installation, you can use the Custom Installation option. The Custom Installation allows you to select the machine’s connection and choose individual components to install. Follow the instructions on the window.

4. Read License Agreement, and select I accept the terms of the License Agreement. Then, click Next.

The program searches for the machine.

If your machine is not found on the network or locally, an error message appears.

• Check if you want to install the software without

connection of the printer.

- Check this option to install this program without a

machine connected. In this case, the print a test page window will be skipped, and completes the installation.

• Search again

When you press this button, appears.

- T

urn off the firewall and Search again. For Windows operating system, click Start > Control Panel > Windows Firewall, and inactivate this option.

- Turn off the firewall from the third party's program

beside the operating system. Refer to the manual provided by individual programs.

• Direct Input

The Dir

ect Input allows you to search for a specific

machine on the network.

- Sea

rch by IP address: Enter the IP address or the host

name. Then click Next. To verify your machine’s IP address, print a network

configuration report (see "Printing Network Configuration report" on page 26).

- Se

arch by network path: To find a shared machine

(UNC Path), enter the shared name manually or find a shared printer by clicking the Browse button. Then click Next.

• Help

If your machine is not connected to the computer or netwo

rk, this help button gives detailed information about

how to connect the machine.

• SNMP Community

Name

If your system administrator set the new SNMP Community

Name on the machine, you can find the

machine in the network. Contact your system administrator for new SNMP Community Name.

5. The

searched machines will be shown on the screen. Select the one

you wish to use and click OK.

If the driver searched only one machine, the confirmation

the firewall notice window

Network setup_ 28

window appears.

6. Follow the instructions in the installation window.

Silent installation Mode

Silent installation mode is an installation method that does not require any user intervention. Once you start the installation, the machine driver and software are automatically installed on you computer. You can start the silent installation by typing /s or /S in the command window.

Command-line Parameters

Following table shows commands that can be used in the command window.

Following command-line are effective and operated when command is used with /s or /S. But /h, /H or /? are exceptional commands that can be operated solely.

Command-

line

/s or /S

/p”<port name>” or /P”<port name>”

/a”<dest_path >” or

/A”<dest_path >”

Starts silent installation. Installs machine drivers

Specifies printer port.

Specifies destination path for installation.

Definition Description

without prompting any UIs or user intervention.

Printer port name can be

Network Port will be created by use of Standard TCP/IP Port monitor. For local port, this port must exist on system before being specified by command.

specified as IP address, hostname, USB local port name or IEEE1284 port name.

For example:

• /p”xxx.xxx.xxx.xxx” in

where, “xxx.xxx.xxx.xxx” means IP address for network printer. /p”USB001”, /P”LPT1:”, /p”hostname”

• When installing the

driver silently in Korean, type in-Setup.exe /s

/L"0x0012” or Setup.exe /s /L"18” .

Since machine drivers should be installed on the

The destination path should be a fully qualified path.

OS specific location, this command applies to only application software.

Command-

line

/i”<script filename>” or

/I”<script filename>”

/n”<Printer name>” or /N”<Printer name>”

/nd or /ND

/x or /X

/up”<printer name>” or /UP”<printer name>”

/d or /D

/v”<share name>” or /V”<share name>”

Definition Description

Specifies customized install script file for custom operation.

The script filename should be a fully qualified filename.

Specifies printer name. Printer instance shall be created as specified printer name.

Commands not to set the installed driver as a default machine driver.

Uses existing machine driver files to create printer instance if it is already installed.

Removes only specified printer instance and not the driver files.

Uninstalls all device drivers and applications from your system.

Shares installed machine and add other available platform drivers for Point & Print.

Customized script file can be assigned for customized silent installation. This script file can be created or modified through provided installer customizing utility or by text editor.

This customized script file is prior than default installer setting in setup package but not prior than command-line parameters.

With this parameter, you can add printer instances as your wishes.

It indicates installed machine driver will not be the default machine driver on your system if there are one or more printer drivers installed. If there is no installed machine driver on your system, then this option won’t be applied because Windows OS will set installed printer driver as a default machine driver.

This command provides a way to install a printer instance that uses installed printer driver files without installing an additional driver.

This command provides a way to remove only specified printer instance from your system without effecting other printer drivers. It will not remove printer driver files from your system.

This command will remove all installed device drivers and application software from your system.

It will install all supported Windows OS platform’s machine drivers to system and share it with specified <share name> for point and print.

Network setup_ 29

Command-

line

/o or /O

Opens Printers and

Faxes folder after

Definition Description

installation.

/f”<log filename>” or

/F”<log filename>”

Specifies log filename. The default log file is created in the system

temp folder if not specified.

/h, /H or /? Shows Command-line

Usage.

Language code

Code Language

0X0009 English

0X0012 Korean

0X0804 Simplified Chinese

0X0404 Traditional Chinese

0x040c French

0X0007 German

0X0010 Italian

0X000a Spanish

0X0013 Dutch

0X001D Swedish

0X0006 Danish

0X000b Finnish

0X0014 Norwegian

0X0019 Russian

0X0005 Czech

0X000e Hungarian

0X0008 Greek

0X0816 Standard Portuguese

0X0416 Brazilian Portuguese

0X0015 Polish

0X001F Turkish

0X0001 Arabic

0X000D Hebrew

0x0424 Slovenian

0X0418 Romanian

0X0402 Bulgarian

0X041A Croatian

0X081A Serbian

This command will open Printers and Faxes folder after the silent installation.

It will create a log file to a specified folder.

Code Language

0X0422 Ukraine

0X041B Slovakia

0X0421 Indonesian

0x041E Thai

0X0429 Farsi

Macintosh

1. Make sure that the machine is connected to your network and

powered on. Also, your machine’s IP address should have been set.

2. Insert the supplied software CD into your CD-ROM drive.

3. Double-click the CD-ROM icon that appears on your Macintosh

desktop.

4. Double-click the MAC_Installer folder.

5. Double-click the Installer icon.

6. Enter the network key and click OK.

7. The Samsung Installer window opens. Click Continue.

8. Select Easy Install and click Install. Easy Install is recommended

for most users. All components necessary for machine operations will be installed.

If you select Custom Install, you can choose individual components to install.

9. When the message which warns that all applications will close on your computer appears, click Continue.

10. Select Typical installation for a network print and click OK.

The certificate window appears, click Trust. See "Setting IP address" on page 27 to use SetIP program.

11. After the installation is finished, click Quit.

12. Open the Applications folder > Utilities > Print Setup Utility.

• For Mac OS X 10.5~ 10.6, open the Applications folder >

System Preferences and click Print & Fax.

13. Click Add on the Printer List.

• For Mac OS X 10.5~ 10.6, press the “+” icon; a display window

will pop up.

14. For Mac OS X 10.3, select the IP Printing tab.

• For Mac OS X 10.4, click IP Printer.

• For Mac OS X 10.5~ 10.6, click IP.

15. Select Socket/HP Jet Direct in Printer Type. When printing a document containing many pages, printing

performance may be enhanced by choosing Socket for Printer Type option.

16. Enter the machine’s IP address in the Printer Address field.

17. Enter the queue name in the Queue Name field. If you cannot

determine the queue name for your machine server, try using the default queue first.

18. For Mac OS X 10.3, if Auto Select does not work properly, select Samsung in Printer Model and your machine name in Model Name.

• For Mac OS X 10.4, if Auto Select does not work properly, select

Samsung in Print Using and your machine name in Model.

• For Mac OS X 10.5~ 10.6, if Auto Select does not work properly,

choose Select a driver to use... and your machine name in Print Using.

Your machine’s IP address appears on the Printer List, and is set

Network setup_ 30

+ 71 hidden pages

Samsung CLP775ND User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

copyright

safety information

regulatory information

about this user’s guide

features of your new product

1.introduction

Machine overview

Control panel overview

Understanding the control panel

Turning on the machine

2.getting started

Setting up the hardware

Supplied software

System requirements

Installing the driver locally

3.network setup

Network environment

Introducing useful network programs

Using a wired network