How it Works
Sam4s
Loading...
Gcube-102
User Manual
24 pgs2.36 Mb0
Table of contents
Loading...

Sam4s Gcube-100, Gcube-102, Gcube Series User Manual

Gcube Series
Receipt Printer
User Guide
All specifications are subject to change without notice.
Warning - U.S.
In case, Operation of this equipment in a residential area is likely to cause harmful interference to radio communications. the user will be required to correct the interference at his own expense.
Notice - Canada
This Apparatus complies with class “A” limits for radio interference as specified in the Canadian department of communications radio interference regulations.
Get appareil est conforme aux normes class “A” d’interference radio tel que specifier par ministre canadien des communications dans les reglements d’interference radio.
Warning
This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
FCC compliance Information(for WLAN and BLUETOOTH)
This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Information to the user
NOTES : This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
OPERATOR’S Manual
3
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
[IMPORTANT NOTE]
FCC RF Radiation Exposure Statement:
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20centimeters between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Caution
Some semiconductor devices are easily damaged by static electricity. You should turn the printer “OFF”, before you connect or remove the cables on the rear side, in order to guard the printer against the static electricity. If the printer is damaged by the static electricity, you should turn the printer “OFF” and contact your dealer for assistance.
INTRODUCTION
The Gcube Series Roll Printer is designed for use with electronic instruments such as system ECR, POS, banking equipment, computer peripheral equipment, etc.
The main features of the printer are as follows:
1. High speed printing Gcube-100 : 250mm/s, 59 lines per second(12X24 Font) Gcube-102 : 250mm/s, 66 lines per second(12X24 Font)
2. Low noise thermal printing.
3. Support a variety of interfaces : USB+RS-232(Serial-25PIN) / USB+WLAN+EHTERNET / USB+ETHERNET+RS-232(Serial-9PIN) /USB+BT+ETHERNET
4. Jam free (Implementation of automatic return of Cutter Jam)
Gcube Series Receipt Printer
4
5. Characters can be scaled up to 64 times compared to it’s original size.
6. The data buffer allows the unit to receive print data even during printing.
7. Bar code printing is possible by using a bar code command.
8. Peripheral units drive circuit enables control of external devices such as cash drawer.
9. 2-dimensional bar code(QR code, PDF-417) and Two color printing.
Please be sure to read the instruction in this manual carefully before using Gcube Series.
NOTES : The Power outlet shall be near the equipment and it should be easily accessible.
LEGISLATION AND WEEE SYMBOL
2002/96/CE Waste Electrical and Electronic Equipment Directive on the treatment, collection, recycling and disposal of electric and electronic devices and their components.
The crossed dustbin symbol on the device means that it should not be disposed of with other household wastes at the end of its working life. Instead, the device should be taken to the waste collection centres for activation of the treatment, collection, recycling and disposal procedure. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract.
This product should not be mixed with other commercial wastes for disposal.
OPERATOR’S Manual
5
Contents
Chapter 1. Setting Up the Printer ·····························7
1.1. Unpacking ································································ 7
1.2. Connecting the Cables
1.3. Connecting the host device
1.4. Connecting the Drawer
1.5. Connecting the Power Supply
1.6. Installing options & Replacing the Paper Roll
1.6.1. Wall Mount Installation
1.6.2. Paper Roll Installation
1.7. Adjustments and Settings ····································· 12
1.7.1. How to install App
1.7.2. Change device setting
1.8. Using the Printer ···················································· 14
1.8.1. Control Panel
1.8.2. Button
1.8.3. Panel lights : FND
···························································
············································ 7
····································· 8
··········································· 8
································· 9
········ 10
···································
·····································
·········································
····································
·················································
··········································
10
11
12
13
14
14
14
CHAPTER 2. APPENDIX ········································· 16
2.1. Adjusting the Paper Near-End Sensor Location ····· 16
2.2. Printer Head Cleaning
2.3. Error Status and Error Resolution
············································ 17
·························· 18
2.4. Specification
2.4.1. General Printer specification
2.4.2. Paper specification
··························································· 20
····························
··········································
20
20
CHAPTER
CHAPTER 1
Setting Up the
1
Printer

1.1. Unpacking

Your printer box should include these items. If any items are damaged or missing, please contact your dealer for assistance.
Interface cable(option) Power-cord Roll paper
Gcube Series
Receipt Printer
User Guide
All specifications are subject to change without notice.
Gcube Series
AC Adapter
Operator’s
Manual(option)

1.2. Connecting the Cables

You can connect up to three cables to the printer. They are all connected to the connector panel on the back of the printer, which is shown as below:
Ethernet
connector
NOTES : Before connecting any of the cables, make sure the both printer and
connecting device are turned off.
Serial connector Drawer Kick-
USB
connector
out connector
OPERATOR’S Manual
Power supply
connector
7

1.3. Connecting the host device

You need the appropriate interface cable.
1. Plug the cable connector securely into the printer’s interface connector.
2. Tighten the screws on both sides of the cable connector.
3. Attach the other end of the cable to the host device.

1.4. Connecting the Drawer

WARNING : Use a drawer that matches the printer specification.
Using an improper drawer may damage the drawer as well as the printer.
CAUTION : Do not connect a telephone line to the drawer kick-out connector;
otherwise the printer and the telephone line may be damaged. Plug the drawer cable into the drawer kick out connector on the back of the printer next to the power supply connector.
To use the drawer, you can connect the cable to the connector.
Gcube Series Receipt Printer
8
Loading...
+ 16 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use