Rocketfish RF-RBWS02 Quick Start Manual
RF-RBWS02 Wireless Outdoor Speaker
Package contents
Sender/Receiver
Wireless speaker
AC power adapter
for sender/receiver
Remote control
3.5 mm to RCA adapter
(6 inches/15.25 cm)
3.5 mm
audio cable
Initial setup
1 Unpack the package contents
2 Adjust the antennas
For best results, raise the antennas of the sender/receiver
to the vertical position.
Tip: In some cases, you may improve range by rotating both antennas
45° to create a 90° angle similar to a wide “V”.
3 Enable the remote control battery
Remove the tab from the bottom of the
remote control.
Installing batteries in the wireless speaker
(skip this if you are not using batteries)
1 Unscrew the bottom cover (three screws).
2 Insert eight alkaline or rechargeable NiMH C
batteries matching the +/- symbols as indicated.
Note: This product will only recharge NiMH batteries.
Do not try to charge any other batteries such as NiCad
batteries in this product.
3 Replace the cover and fasten the three screws.
4 Turn on the wireless speaker using the power
switch on the top panel.
Wireless
speaker
User Guide
AC power adapter
for wireless speaker
Quick Setup Guide
Eight alkaline or
rechargeable NiMH C
batteries (not included)
× 8
Connecting the DC adapter to the wireless speaker
(if you are not using batteries, or if you want to charge the batteries)
1 Connect the AC power adapter to the wireless
speaker and plug into an AC power outlet.
2 Turn on the wireless speaker using the power switch
on the top panel.
Note: If you are using NiMH rechargeable batteries, your
batteries will recharge whenever the speaker is connected
to a power outlet with the DC adapter. If batteries are not
fully charged, you should charge them for 16 hours before
using the wireless speaker.
BASS
15VDC
15V DC
Connecting audio source and power to sender/receiver
1 Connect one end of the audio cable (supplied) to the AUDIO IN jack on the sender/receiver
and the other end to the audio output jack of your device (such as an A/V receiver, PC, or iPod).
Included
3.5 mm cable
To audio
output jack
2 Remember to turn the volume up on the source device to at least 80% of its maximum volume
if connected to a headphone output.
3 Connect the AC power adapter to the sender/receiver and plug into an AC power outlet.
The sender/receiver automatically turns on and the power indicator turns green.
OR
Included 3.5 mm cable and
3.5 mm to RCA adatper
To audio
output jack
Establishing communication
The sender/receiver and wireless speaker were pre-joined so they will communicate with each
other right out of the box. So if this is your rst Rocketboost enabled product you can skip this step
and go to the next section, Listening to music step.
If you need to rejoin the sender/receiver to the wireless speaker, and this is your only Rocketboost
enabled product, then use the following steps.
1 Set the HUB STATUS switch on the sender/receiver to ENABLE if this is your rst Rocketboost
product set.
• The power indicator turns green when the HUB STATUS switch is set to ENABLE.
• The power indicator turns blue when the HUB STATUS switch is set to DISABLE.
2 Press and hold on the sender/receiver for more than three seconds to put it into joining
mode. The power indicator starts blinking rapidly and the unit will stay in joining mode for
30 seconds.
3 Press and hold the power/join button on the wireless speaker for more than three seconds
so the sender/receiver and wireless speaker enter connection mode.
• The power indicator lights steadily if the joining was successful.
• The power indicator blinks slowly if the joining was not successful.
4 After the link is established, if the Source indicator on
the wireless speaker is still not illuminated, make sure
that your source is turned on.
For more instructions, see your User Guide.
If you already have other Rocketboost devices you need
to join both the sender/receiver and the wireless speaker
Lights when
speaker is
receiving
audio from
sender
to your existing hub device. See the User Guide for
detailed instructions on how to do this.
Listening to music
1 Turn on the wireless sender/receiver and wireless speaker. The power indicator LEDs should
light steadily. If they are blinking you need to rejoin the sender/receiver and wireless speaker.
See the Establishing communication step above.
2 Play music from the audio device connected to your sender/receiver and listen to it from the
wireless speaker.
3 Adjust the volume level on your wireless speaker. If you have multiple audio sources in your
Rocketboost network, press the Source button on the wireless speaker to hear the next audio
source. Press the Source button again to cycle through all available audio sources.
Rocketboost network notes:
Every Rocketboost network must contain
one hub device, which helps devices join
the network. The network can have only
one hub, which you can enable using the
hub switch on the back of all Rocketboost
senders and sender/receivers. If this is your
rst Rocketboost product, you should
make this device the hub, if you already
have Rocketboost products, you should
disable hub mode on this device.
Important: Hub devices must always have
power for your network to operate. The
hub device can be in standby (powersaving) mode, but must stay plugged in.
QUICK SETUP GUIDE
© 2010 BBY Solutions, Inc., All Rights Reserved. Distributed by Best Buy Purchasing, LLC, 7601 Penn Avenue South, Richeld, MN USA 55423-3645
ENGLISH 10-0969
Loading...