Operation 8030C
MENU
PROGRAM
RESET
Calibration
NOTE: Your thermostat comes from the factory calibrated to + or - 1oF actual temperature. It is an accurate instrument. If you want your thermostat to display the same temperature as another thermometer in your home, you can adjust its calibration.
To change the calibration:
The unit must be in the HEAT or COOL mode. Press the MENU button.
Press the Temp Up/Temp Down arrows to adjust the temperaturereading.
CALIBRATE DISPLAY ON will appear.
Press HOME to save the new setting. |
MENU |
|
PROGRAM |
|
-TFACTOR |
|
RESET |
|
DISPLAY |
|
CALIBRATE |
Customer Support: 888-515-2585 or Visit our webiste |
www.ritetemp-thermostats.com |
Made in China |
401-011 |
Operation 8030C
Time |
Time |
|
|
Touch Screen |
|
Slot |
|
|
|
|
|
of day |
|
|
|
Menu |
|
|
|
|
|
||
Day |
|
|
|
|
button |
|
|
|
|
|
|
|
|
|
MENU |
|
Program |
|
|
|
|
|
|
|
|
|
|
|
button |
|
|
|
PROGRAM |
|
Current |
|
|
|
|
|
|
|
|
|
|
|
Room |
|
|
|
|
RESET |
Temperature |
|
|
|
|
|
|
|
|
|
|
|
Reset |
|
|
|
|
|
button |
|
|
|
|
|
Target |
|
|
|
|
|
Temperature |
|
Fan |
Mode |
Thermostat |
||
|
Switch |
Mode |
|
|
|
|
Switch |
|
|
||
|
|
|
|
|
Statement of use: The GPMG8030C can be used with most 24 volt gas, oil or electric heating and air conditioning systems, single-stage heat pumps or gas millivolt heating systems. It cannot be used with 120 volt heating systems or multistage heat pumps.
Using a TOUCH SCREEN
Please take a moment to try out your touch screen itself.
To select a function on the touch screen, place your finger on the main temp display and give a short firm push. Try a "tap" of the finger or stylus. Your input must last long enough for the system to determine it is not an accidental 'bump'.
Using the stylus is more comfortable for some users. Again allow the system enough time to recognize your inputs. When you are comfortable with
touch inputs, proceed. 1
PG
Basic Screens |
|
|
|
|
The MODE SWITCH of the 8030C must be in the HEAT or the COOL position |
|
|||
to access all control functions. The 8030C Thermostat has 3 basic screens. |
|
|||
The HOME screen is displayed when unit is operating your system. |
|
|||
Touching the |
will always return you to this screen. |
|
||
Day |
Time |
|
|
|
Slot |
|
|
||
|
|
|
||
|
|
Current Room |
||
|
|
Temperature |
||
Time of day |
|
|
|
|
Touch here |
|
|
|
|
to change |
|
|
|
|
from 12 to 24hr |
|
Target |
|
|
clock display. |
|
Temperature |
||
|
Chirp indicator |
Thermostat |
|
|
HOME screen |
Mode |
2 |
||
PG |
||||
|
|
MENU screen
Displayed when the MENU button is pressed from the HOME screen.
1 Set Day
Touch this area to set the day of the week.
2 Set Time
Touch this area to set the time of day.
Left arrow goes back, right arrow goes forward.
Temperature Swing set
Filter Timer set
Set oC -oF |
Lock Program |
Touch this to |
Touch for 5 sec |
set temperature |
to lock or unlock |
display. |
|
-T FACTOR
CALIBRATE DISPLAY
3
Return HOME
Calibration indicator
This comes on if you have altered the calibration of your unit
Chirp set
Touch this to turn the audible chirp on or off.
Calibration
Use this to calibrate your LCD display to match another thermometer. PG 3
PROGRAM screen
Displayed when the PROGRAM button is pressed from the HOME
Set Program Day |
Set Time Slot |
Touch this area to set |
Touch this area to set |
the day of the week you |
the Time Slot you |
want to program Target |
want to program. |
Temps for. |
|
Set Program Time |
|
Touch this area to set the |
|
time of day you want each |
|
time period to start. |
|
Left arrow goes back, |
|
right arrow goes forward. |
|
Copy
Touch this area to copy current program to the next day
Return HOME
When programming is complete touch this to run your program.
Temp Up / Temp Down arrows. Touch these to raise and lower
each Target Temp. PG 4