Operation 8022C
SET TEMP
HEAT
F
PM
OFF
HEAT
COOL
FAN |
ON |
|
AUTO
SET TEMP
HEAT
F
PM
OFF
HEAT
COOL
FAN |
ON |
|
AUTO
Customer Support: 888-515-2585 or |
|
Visit our webiste www.ritetemp-thermostats.com |
|
Made In China |
401-006 |
|
Operation 8022C
|
TEMP UP |
Time/ Current Temp |
AA Battery |
|||
|
button |
|
Display |
Compartment |
||
- Cover Closed - |
|
|
|
|
|
|
|
|
|
|
|
TEMP |
|
|
|
|
|
|
UP |
BATTERY |
|
|
|
|
|
|
TEMP |
|
|
|
|
|
|
SET |
|
SET TEMP |
|
|
|
|
|
|
|
|
|
|
|
PM |
|
PM |
|
|
|
|
|
|
|
|
FAN |
ON |
|
|
|
|
|
|
|
|
|
|
|
OFF |
AUTO |
|
|
|
|
|
|
COOL |
|
|
|
|
|
HEAT |
|
|
|
|
|
|
|
|
Fan |
|
DOWN |
|
|
|
|
|
|
|
|
|
|
|
Switch |
|
|
|
Set Temp |
|
Mode |
|
|
|
TEMP DOWN Display |
|
|
|
|||
|
Switch |
|
|
|||
|
button |
|
|
|
||
|
|
|
|
|
|
|
|
Statement of use: The GPMG8022c can be used with |
|
||||
|
most 24 volt gas, oil or electric heating and air conditioning |
|
||||
|
systems, single-stage heat pumps or gas millivolt heating |
|
||||
PG 1 |
systems. It cannot be used with 120 volt heating |
|
|
|||
systems or multistage heat pumps. |
|
|
|
|||
|
|
|
SET |
|
|
TIME |
|
|
SDP |
TIME |
|
|
|
|
|
|
CLOCK |
SLOT |
|
SET |
|
||
|
TIME |
TIME |
|
|
|
|
|
|
|
P |
|
HOME |
|
NEXT |
FILTER |
DAY |
|
||
|
HOLD |
REVIEW |
|
|
|
TEMP |
FAN |
|
|
COPY |
|
|
PROGRAM |
RESET |
|
|
MODE |
|
|
Reset button
Control Panel
Fan
Switch
Heat/Cool
Mode Switch
1 Set Clock
Set day of the week -
Press SET CLOCK once to set the day of the week. The day of the week display flashes. (Initially SU for Sunday)
Press <TI |
or |
TIME |
> |
|
|
|
TIME |
|
|
|
|
||
to select the day. |
|
|
TEMP |
|
||
Press HOME to store your |
|
|||||
UP |
|
|||||
settings. |
|
|
|
BATTERY |
|
|
|
|
|
|
|
||
|
|
|
|
|
SET CLOCK |
|
Set time of day - |
|
|
SET TEMP |
|
||
|
|
P2 |
HOME |
|||
Press SET CLOCK twice to set |
||||||
|
||||||
F |
DAY |
|||||
the time. The time display will |
|
|||||
|
|
|||||
flash. |
|
|
|
|
PROGRAM |
|
|
|
|
|
|
||
Press <TIME or |
TIME> to set |
|
MODE |
|||
the time. Press and hold to set |
DOWN |
|
||||
the time in the fast mode. |
|
|
||||
Press HOME to store your |
|
|
||||
settings. |
|
|
|
|
|
|
PG 2 |
|
|
|
|
|
|
SDP |
TIME SET |
TIME SLOT |
TIME |
NEXT P |
TIME |
TEMP HOLD |
FILTER |
COPY |
REVIEW |
RESET
FAN
2 Auto-run
This Thermostat comes preprogrammed with an Energy-StarTM approved program. This program is recommended by the EPA for energy efficiency.
We strongly recommend that you Auto-Run this program for one week, and see if it works for you. If it does not fit your needs you can always input a custom program.
To Auto-Run the Energy-StarTM program, select HEAT or COOL with the mode switch. The unit is now running the Energy-StarTM program.
The clock and the ambient temperature are displayed on the right.
They alternate every 2 seconds. One of the TIME SLOT icons P1/P2/P3/P4 comes on, this indicates the TIME SLOT active in the Energy-StarTm program.
The programmed temperature is shown on the left. For program details refer to the Energy-StarTM program chart below.
|
HEAT |
P1 |
P2 |
P3 |
P4 |
COOL |
P1 |
P2 |
P3 |
P4 |
|
|
6:00am |
8:00am |
6:00pm |
10:00pm |
|
6:00am |
8:00am |
6:00pm |
10:00pm |
PG 3 |
All Days |
70oF |
62oF |
70oF |
|
All Days |
78oF |
85oF |
78oF |
|
|
|
|
|
|
|
|
|
|
|
NOTE: 60 Second Rule-During programming, if a button is not pushed within 60 seconds, the unit will go out of the set mode.
Everything you have input in this programming will automatically be saved.
Select HEAT with the HEAT/Cool MODE switch.
Select the day you want to program: Press the PROGRAM to enter programming mode. The
PROGRAM FOR icon will come on. The day icon will show SU (Sunday). Press dayDAY again to advance the day selection.
Select the TIME SLOT you want to program: To change the TIME SLOT (P1, P2, P3, P4) press the NEXTXT P button. The display will cycle through the
time periods in sequence. Select P1.
Select the desired temperature for that TIME SLOT : To change the temperature for that TIME SLOT press the TEMP UP / TEMP DOWN buttons.
Select the time of day you want that TIME SLOT to represent:
To set the time when P1 will begin , press the TIME<TI or TIMETIME> buttons to PG 4 move the set point forward or backward in time.
Loading...