ReliOn BP200, HEM-741CRELN4 Instruction Manual

BP200 Blood

Pressure Monitor

Model HEM-741CRELN4

INSTRUCTION MANUAL

ESPAÑOL

ENGLISH

TABLE OF CONTENTS

Before using the monitor

Introduction .............................................................................................................3

Safety information...................................................................................................4

Intended use............................................................................................4

General usage .........................................................................................4

General usage .........................................................................................5

Battery usage ..........................................................................................5

General precautions................................................................................6

Operating instructions

Before taking a measurement ..................................................................................7

Know your unit........................................................................................................8

Unit display .............................................................................................................9

Display symbols ....................................................................................................10

Irregular heartbeat symbol....................................................................10

Movement error symbol .......................................................................10

Average reading symbol.......................................................................10

Heartbeat symbol..................................................................................10

Blood pressure level indicator..............................................................11

Battery installation ................................................................................................12

Setting the date and time .......................................................................................13

Applying the ARM cuff .......................................................................................14

Applying the cuff on the left ARM ......................................................14

Applying the cuff on the right ARM ....................................................15

Taking a measurement...........................................................................................16

Using the memory function...................................................................................19

To view the measurement values stored in memory ............................19

To view the average reading ................................................................19

To delete all values stored in the memory............................................20

Care and maintenance.................................................................................................21

Error indicators......................................................................................................22

Troubleshooting tips..............................................................................................24

FCC statement .......................................................................................................25

Guidance and manufacturer’s declaration.............................................................26

Limited warranty ...................................................................................................33

Specifications ........................................................................................................35

2

INTRODUCTION

Thank you for purchasing the ReliOnTM BP200 Blood Pressure Monitor, Model
# HEM-741CRELN4.

Your new blood pressure monitor uses the oscillometric method of blood pressure
measurement. This means the monitor detects your blood’s movement through your
brachial artery and converts the movements into a digital reading. An oscillometric
monitor does not need a stethoscope so the monitor is simple to use.
The ReliOn

TM

BP200 Blood Pressure Monitor, Model # HEM-741CRELN4 comes with

the following components:

• Monitor • Wide Range Arm Cuff • 4 "AA" Alkaline Batteries

• Instruction Manual • Quick Start Guide

Please read this instruction manual thoroughly before using the unit.
Please keep for future reference.
For specific information about your own blood pressure, CONSULT YOUR DOCTOR.

Fill in for future reference.

DATE PURCHASED: __________________

SERIAL NUMBER: ____________________

• Staple your purchase receipt here

SAVE THESE INSTRUCTIONS

3

SAFETY INFORMATION

INTENDED USE

This device is a digital monitor intended for use in measuring blood pressure and pulse
rate in adult patient population. The device detects the appearance of irregular
heartbeats during measurement and gives a warning signal with the readings.

To assure the correct use of the product, basic safety measures should always be
followed including the warnings and cautions listed in this instruction manual.

SAFETY SYMBOLS USED IN THIS INSTRUCTION MANUAL

WARNING

Indicates a potentially hazardous situation which, if not avoided,
could result in death or serious injury.

CAUTION

Indicates a potentially hazardous situation which, if not avoided,
may result in minor or moderate injury to the user or patient or
damage to the equipment or other property.

GENERAL USAGE

DO NOT adjust medication based on measurement values from this blood pressure
monitor. Take medication as prescribed by your physician. Only a physician is
qualified to diagnose and treat High Blood Pressure.
The monitor is not intended to be a diagnostic device.
Consult your physician before using the device for any of the following conditions:
common arrhythmias such as atrial or ventricular premature beats or atrial
fibrillation, arterial sclerosis, poor perfusion, diabetes, age, pregnancy,
pre-eclampsia, renal diseases.
Note that PATIENT motion, trembling, shivering may affect the measurement value.
Do not use the device on the injured arm or the arm under medical treatment.
Do not apply the arm cuff on the arm while on an intravenous drip or blood transfusion.
Consult your physician before using the device on the arm with an arterio-venous
(A-V) shunt.
Do not use the device with other medical electrical (ME) equipment simultaneously.
Do not use the device in the area of HF surgical equipment, MRI, or CT scanner, or
in an oxygen rich environment.
The air tube may cause accidental strangulation in infants.
Contains small parts that may cause a choking hazard if swallowed by infants and
small children.

4

5

SAFETY INFORMATION

GENERAL USAGE

Always consult your physician. Self-diagnosis of measurement values and
self-treatment are dangerous.
Consult your physician before using the device for any of the following conditions:

• If you have had a mastectomy.

• People with severe blood flow problems or blood disorders as cuff inflation can

cause bruising.
Do not take measurements more than necessary. It may cause bruising due to blood
flow interference.
Remove the arm cuff if it does not start deflating during the measurement.
Do not use this device on infants or persons who cannot express their intentions.
Do not use the device for any purpose other than measuring blood pressure.
Use only the approved arm cuff for this device. Use of other arm cuffs may result in
incorrect measurement values.
Do not use a mobile phone or other devices that emit electromagnetic fields near the
device. This may result in incorrect operation of the device.
Use only Omron authorized parts and accessories. Parts and accessories not approved
for use with the device may damage the unit.
Do not disassemble the monitor or arm cuff. This may cause an inaccurate reading.
Do not use in a location with moisture, or a location where water may splash on the
device. This may damage the device.
Do not use the device in a moving vehicle. For example, the car or airplane.

Read "If your systolic pressure is more than 210 mmHg" in "TAKING A
MEASUREMENT" section in this manual, if your systolic pressure is known to be

more than 210 mmHg. Inflating to a higher pressure than necessary may result in
bruising where the cuff is applied.

BATTERY USAGE

Do not insert the batteries with their polarities incorrectly aligned.
Use only 4 "AA" alkaline or manganese batteries with this device. Do not use other
types of batteries. Do not use new and used batteries together.
Remove the batteries if the device will not be used for three months or more.
If battery fluid should get in your eyes, immediately rinse with plenty of clean water.
Contact a physician immediately.

6

SAFETY INFORMATION

GENERAL PRECAUTIONS

• Do not forcibly crease the arm cuff or the air tube excessively.

• Do not press the air tube while taking a measurement.

• To unplug the air plug, pull on the air plug at the connection with the monitor, not

the tube itself.

• Do not drop the monitor or subject device to strong shocks or vibrations.

• Do not inflate the arm cuff when it is not wrapped around your arm.

•

Do not use the device outside the specified environment. It may cause an inaccurate reading.

• Dispose of the device, components and optional accessories according to applicable

local regulations. Unlawful disposal may cause environmental pollution.

7

BEFORE TAKING A MEASUREMENT

To ensure a reliable reading follow these recommendations:

1. Avoid eating, drinking alcohol, smoking, exercising, and bathing for 30 minutes before
taking a measurement. Rest for at least 5 minutes before taking the measurement.

2. Stress raises blood pressure. Avoid taking measurements during stressful times.

3. Measurements should be taken in a quiet place.

4. Remove tight-fitting clothing from your arm.

5. Sit on a chair with your feet flat on the floor. Rest your arm on table so that the cuff
is at the same level as your heart.

6. Remain still and do not talk during the measurement.

7. Keep a record of your blood pressure and pulse readings for your physician. A
single measurement does not provide an accurate indication of your true blood
pressure. You need to take and record several readings over a period of time. Try to
measure your blood pressure at the same time each day for consistency.

8

KNOW YOUR UNIT

Main Unit:

Components:

Quick Start
Guide

Instruction
Manual

Air plug

Air tube

Wide Range Cuff (# CD-WR17)
(Model: HEM-RML31)

Arm Cuff (Arm circumference
9” - 17” (22 - 42 cm))

Date/Time setting
button

Memory button

Start/Stop button

"AA" Alkaline Batteries

( / )

Air jack

Display

Up/Down

buttons

User selection switch

Battery compartment

<

>

BP200

Blood Pressure

Monitor

Blood Pressure Monitor

Quick Start Guide

5130643-5A

5130639-7A

UNIT DISPLAY

Average reading symbol

User symbol (A/B)

Battery symbol (low/depleted)

Blood pressure level indicator
(High/Normal)

Date/Time display

Memory symbol

Diastolic blood pressure

Systolic blood pressure

Irregular heartbeat symbol

Movement error symbol

Heartbeat symbol
(Flashes during measurement)

Pulse display and Memory number

Deflation symbol

9

DISPLAY SYMBOLS

IRREGULAR HEARTBEAT SYMBOL ( )

When the monitor detects an irregular rhythm two or more times during the

measurement, the Irregular Heartbeat Symbol will appear on the display with the
measurement values.

An irregular heartbeat rhythm is defined as
a rhythm that varies by 25% less or 25%
more than the average rhythm detected
while the monitor is measuring the systolic
and diastolic blood pressure.

If the irregular heartbeat symbol
displays with your measurement values,
we recommend you consult your
physician. Follow the directions of your
doctor.

MOVEMENT ERROR SYMBOL ( )

The Movement Error Symbol is displayed if you move your body during the
measurement. Please remove the arm cuff, and wait 2-3 minutes. Re-apply the arm cuff
and take another measurement.

AVERAGE READING SYMBOL ( )

The Average Reading Symbol is displayed when you press and hold the button
for more than 3 seconds.

The average reading based on the last 3 measurement values taken within 10 minutes
appears on the display screen.

HEARTBEAT SYMBOL ( )

The Heartbeat symbol flashes on the display at every heartbeat during the measurement.

Normal Heartbeat

Irregular Heartbeat

Short Long

Blood

pressure

Pulse

Pulse

Blood

pressure

10

DISPLAY SYMBOLS

BLOOD PRESSURE LEVEL INDICATOR ( )

If your Systolic Blood Pressure is 135 mmHg or above and/or the
Diastolic Blood Pressure is 85 mmHg or above, the High Blood
pressure level indicator ( ) will display when the measurement
value is displayed.
If the measurements are within the standard range, the Normal
Blood pressure level indicator ( ) will display.

Office Home

Systolic Blood Pressure ≥ 140 mmHg ≥ 135 mmHg

Diastolic Blood Pressure ≥ 90 mmHg ≥ 85 mmHg

2013 ESH/ESC Guidelines for the management of arterial hypertension

Definitions of hypertension by office and home blood pressure levels

These are from statistical values for blood pressure.

11

BATTERY INSTALLATION

1. Press the hook on the top of the battery cover and lift the
cover off in the direction of the arrow.

2. Install 4

"

AA" size batteries so the + (positive) and

- (negative) polarities match the polarities of
the battery compartment as indicated.

Battery Cover

3. Replace the battery cover.

NOTES: • When the depleted battery symbol ( ) appears on the display, turn the

monitor off, then replace all batteries at the same time. Long life alkaline
batteries are recommended.

• Turn the unit off before replacing the batteries. If the batteries are removed
while the unit is still on, the date and time will be reset to that of the
previous use. The measurement values are not deleted.

• When the batteries are replaced, you may need to reset the date and time.

If “-:--” appears on the display, refer to “Setting the Date and Time”.

• The batteries included with the device may have a shorter life.

12

SETTING THE DATE AND TIME

Set the monitor to the correct date and time before taking a measurement for the first time
or after replacing the batteries.

1.

Press the button to show the year.

Year

Month

Day

Hour

Minute

Change Confirm

Change Confirm

Change Confirm

Change Confirm

Change Confirm

: Forward
: Back

4. Press the Start/Stop button to turn the monitor off.

<

>

<

>

<

>

<

>

<

>

2. Push or button to change the year.

3.

The year can be set between 2015 and 2045.

When the display reaches 2045, it will return to 2015.

Push the button to confirm the year and then the month flashes. Repeat the same
steps to change the month, day, hour, and minute.

NOTE:

Press and hold

or

button to increase the date and time values faster.

<

>

<

>

>

<

13

APPLYING THE CUFF ON THE LEFT ARM

1. Make sure the air plug is securely inserted
in the main unit.

2. Remove tight-fitting clothing from your upper
arm.

3. Apply the cuff to your left upper arm so
the air tube is centered on the inside of your
arm and aligned with your middle finger.
The air tube runs down the inside of your arm.
The bottom of the cuff should be
approximately 1/2 inch (1 - 2 cm) above your elbow.

4. Wrap the cuff firmly in place around your

arm using the cloth fastening in the direction

of the arrow.

APPLYING THE ARM CUFF

Air Tube

1/2 inch (1 - 2 cm)

Left Arm

14

APPLYING THE ARM CUFF

APPLYING THE CUFF ON THE RIGHT ARM

When taking a measurement using the right arm, use this instruction for Step 3.

Apply the cuff to your right upper arm so the
air tube runs along the inside of your arm.
The bottom of the cuff should be approximately
1/2 inch (1 - 2 cm) above your elbow.

NOTES: • Be careful not to rest your arm on the air tube. This will restrict the flow of

• When you take a measurement on the right arm, the air tube will be at the

air to the cuff.

side of your elbow. Be careful not to rest your arm on the air tube.

Right Arm

15

TAKING A MEASUREMENT

A

B

The monitor is designed to store the blood pressure and the pulse rate in the memory
for two people (USER A or USER B) every time a measurement is completed.

1. Sit on a chair with your feet flat on the floor.
Place your arm on a table so the cuff is level
with your heart.
Remain still and do not talk during

measurement.

2. Select your user ID (A or B).

16

3. Press the Start/Stop button. All symbols appear on the display.

The cuff starts to inflate automatically. As the cuff inflates, the monitor
automatically determines your ideal inflation level.

Remain still and do not move your arm until the entire measurement process is

completed.

NOTE: To stop the inflation or measurement, push the Start/Stop button. The

monitor will stop inflating, start deflating, and will turn off.

If your systolic pressure is more than 210 mmHg

After the arm cuff starts to inflate, press and hold the Start/Stop button until the
monitor inflates 30 to 40 mmHg higher than your expected systolic pressure.

NOTE: The monitor will not inflate above 299 mmHg.

Inflating to a higher pressure than necessary may result in bruising where the
arm cuff is applied.

TAKING A MEASUREMENT

17

TAKING A MEASUREMENT

6. Remove the arm cuff.

7. Press the Start/Stop button to turn the monitor off.

NOTES: • The monitor will automatically turn off after
2 minutes.

• Wait 2-3 minutes before taking another
measurement. Waiting between measurements

allows the arteries to return to the condition prior
to taking a measurement. You may need to increase
the wait time depending on your individual physiological
characteristics.

5. When the measurement is complete, the arm cuff completely

deflates. Your blood pressure and pulse rate are displayed.

4. Inflation stops automatically and the measurement is started.
As the cuff deflates, decreasing numbers appear on the display and the Heartbeat

Symbol ( ) flashes.

18

: To view the older values
: To view the more recent values

3. Press the or button to view the values stored in the memory.

4. Press the Start/Stop button to turn the monitor off.

• If there are no measurement values stored in the

memory, the screen to the right is displayed.

<

>

>

USING THE MEMORY FUNCTION

The monitor automatically stores the results up to 60 sets for each user (A and B). It
can also calculate an average value based on the last 3 measurement values taken
within 10 minutes.

TO VIEW THE MEASUREMENT VALUES STORED IN MEMORY

1. Select your USER ID (A or B).

2. Press the button to display the set of measurement values.
The Memory number appears for a second before the pulse rate is displayed. The
most recent reading is numbered “1”.

<

NOTES: • If the memory is full, the monitor will delete the oldest value.

• The date and time are alternately displayed with the

measurement values.

• When viewing the measurement value taken without setting the
date and time, "-:--" is displayed instead of the date and time.

TO VIEW THE AVERAGE READING

1. Select your USER ID (A or B).

2. Press and hold the button for more than 3 seconds.

19

USING THE MEMORY FUNCTION

TO DELETE ALL VALUES STORED IN THE MEMORY

The values stored in the memory are deleted by USER ID.

You cannot partially delete values stored in the memory. All values for the user you
select will be deleted.

1. Select your USER ID (A or B).

2. Press the button to turn the monitor on.

3. When the memory symbol ( ) appears, while pressing and holding the

button, press the Start/Stop button for 3 seconds to delete all values in the memory.

4. Press the Start/Stop button to turn the monitor off.

NOTE: The monitor will automatically turn off after 2 minutes.

NOTES: • If the previous measurement was taken without

setting the date and time, the average reading is
not calculated.

• If two sets of measurement values are stored in the
memory for the 10 minute period, the average is
based on the two sets of measurement values. If
only one set of measurement values is stored, this is
displayed as the average.

20

CARE AND MAINTENANCE

To keep your blood pressure monitor in the best condition and protect the unit from
damage, follow the directions listed below:

Do not forcefully bend the arm cuff or air tube. Do not fold tightly.

Clean the monitor with a soft dry cloth.

Do not use any abrasive or volatile cleaners.
Do not attempt to clean the cuff.

CAUTION

Do not submerge the device or any of the components in water.
Do not subject the monitor to extreme hot or cold temperatures, humidity or
direct sunlight.

CAUTION

Store the device and the components in a clean, safe location.

CAUTION

Do not subject the monitor to strong shocks, such as dropping the unit on the floor.

Remove the batteries if the unit will not be used for three months or longer. Always
replace all the batteries with new ones at the same time.

Use the unit in a manner consistent with the instructions provided in this manual.

CAUTION

Use only authorized parts and accessories. Parts and accessories not
approved for use with the device may damage the unit.

CAUTION

Changes or modification not approved by the manufacturer will void the user
warranty. Do not disassemble or attempt to repair the unit or components.

21

ERROR INDICATORS

Air plug disconnected.

Arm cuff not applied
correctly.

Air is leaking from the
arm cuff.

Cuff over or under
inflated.

Batteries are depleted.

Insert the plug securely. Refer to
"APPLYING THE ARM CUFF".

Irregular heartbeats are
detected.

Remove the arm cuff. Wait 2-3 minutes and

then take another measurement.

Repeat the steps in "TAKING A
MEASUREMENT". If this error continues

to appear, contact your physician.

Movement during
measurement.

Remain still and do not talk during the
measurement.
Carefully read and repeat the steps in

"TAKING A MEASUREMENT".

Batteries are low.

Recommend to replace the batteries with
new ones ahead of time.

Refer to "BATTERY INSTALLATION".

Apply the arm cuff correctly. Refer to
"APPLYING THE ARM CUFF".

Replace the four batteries.
Refer to "BATTERY INSTALLATION".

Repeat measurement. Remain still and do
not talk during measurement. Refer to
"TAKING A MEASUREMENT".

If "E2" appears repeatedly, inflate the cuff
manually until it is 30 to 40 mmHg above
your previous measurement result. Refer
to "TAKING A MEASUREMENT".

Replace the cuff with a new one.

SYMBOL CAUSE CORRECTION

22

ERROR INDICATORS

SYMBOL CAUSE CORRECTION

Do not inflate the cuff above 299 mmHg.
Refer to "TAKING A MEASUREMENT".

Remove any clothing interfering with the
arm cuff. Refer to "APPLYING THE
ARM CUFF".

Repeat measurement. Remain still and do
not talk during measurement. Refer to
"TAKING A MEASUREMENT".

Contact Customer Service.

Device error.

Movement during
measurement.

Clothing is interfering
with the arm cuff.

The arm cuff was inflated
above 299 mmHg when
inflating the cuff manually.

23

24

TROUBLESHOOTING TIPS

PROBLEM

No power.
No display appears on the unit.

Measurement values appear too
high or too low.

CAUSES AND SOLUTIONS

Replace all four batteries with new ones.
Check the battery installation for proper placement
of the battery polarities.

Blood pressure varies constantly. Many factors
including stress, time of day, how you wrap the
cuff, may affect your blood pressure.
Review the sections "BEFORE TAKING A
MEASUREMENT" and "TAKING A
MEASUREMENT".

FCC STATEMENT

FCC CAUTION

Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.

Note:

This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the
following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

25

GUIDANCE AND MANUFACTURER’S DECLARATION

ReliOn Blood Pressure Monitor

Model: HEM-741CRELN4

Information for accompanying documents in the scope of IEC60601-1-2:2007

Important information regarding Electro Magnetic Compatibility (EMC)

With the increased number of electronic devices such as PC’s and mobile (cellular)
telephones, medical devices in use may be susceptible to electromagnetic
interference from other devices. Electromagnetic interference may result in
incorrect operation of the medical device and create a potentially unsafe situation.
Medical devices should also not interfere with other devices.

In order to regulate the requirements for EMC (Electro Magnetic Compatibility)
with the aim to prevent unsafe product situations, the IEC60601-1-2 standard has
been implemented. This standard defines the levels of immunity to electromagnetic
interferences as well as maximum levels of electromagnetic emissions for medical
devices.

Medical devices manufactured by OMRON Healthcare conform to this
IEC60601-1-2:2007 standard for both immunity and emissions.Nevertheless,
special precautions need to be observed:

• The use of accessories and cables other than those specified by ReliOn, with the
exception of cables sold by ReliOn as replacement parts for internal components,
may result in increased emission or decreased immunity of the device.

• The medical devices should not be used adjacent to or stacked with other
equipment.In case adjacent or stacked use is necessary, the medical device should
be observed to verify normal operation in the configuration in which it will be
used.

• Refer to further guidance below regarding the EMC environment in which the
device should be used.

• The MEDICAL ELECTRICAL EQUIPMENT HEM-741CRELN4 needs special

precautions regarding EMC and needs to be installed and put into service
according to the EMC information provided in this documentations.

• The Essential Performance of the HEM-741CRELN4 is to measure a blood
pressure and a pulse rate and using the memory function.

The HEM-741CRELN4 may be interfered with by other equipment, even if that
other equipment complies with CISPR EMISSION requirements.

26

GUIDANCE AND MANUFACTURER’S DECLARATION

Guidance and manufacturer’s declaration – electromagnetic emissions

Emissions test

Harmonic emissions
IEC 61000-3-2

Voltage fluctuations/
flicker emissions
IEC61000-3-3

ReliOn

TM

HEM-741CRELN4 is intended for use in the electromagnetic environment

specified below. The customer or the user of this ReliOn

TM

HEM-741CRELN4

should assure that it is used in such environment.

Electromagnetic environment
– guidance

Group 1

Class B

RF emissions CISPR 11

RF emissions CISPR 11

The ReliOn

TM

HEM-741CRELN4 uses RF
energy only for its internal function.
Therefore, its RF emissions are very low
and are not likely to cause any interference
in nearby electronic equipment.

The ReliOn

TM

HEM-741CRELN4 is suitable
for use in all establishments, including
domestic establishments and those directly
connected to the public low-voltage power
supply network that supplies buildings used
for domestic purposes.

Compliance

Not
Applicable.

Not
Applicable.

27

GUIDANCE AND MANUFACTURER’S DECLARATION

Electrostatic
discharge (ESD)
IEC 61000-4-2

±6 kV contact
±8 kV air

±6 kV contact
±8 kV air

Floor should be wood, concrete, or
ceramic tile. If floors are covered
with synthetic material, the relative
humidity should be at least 30 %.

Electrical fast
transient/burst
IEC 61000-4-4

±2 kV for
power
supply lines
±1 kV for
input/output
lines

Not
Applicable.

Not Applicable.

Surge
IEC 61000-4-5

±1 kV
line(s) to
line(s)
±2 kV
line(s) to
earth

Not
Applicable.

Not Applicable.

Immunity test

IEC 60601
test level

Compliance
level

Electromagnetic environment

- guidance

Guidance and manufacturer’s declaration - electromagnetic immunity

ReliOn

TM

HEM-741CRELN4 is intended for use in the electromagnetic environment

specified below. The customer or the user of this ReliOn

TM

HEM-741CRELN4 should

assure that it is used in such environment.

28

GUIDANCE AND MANUFACTURER’S DECLARATION

Immunity test

IEC 60601
test level

Compliance
level

Electromagnetic environment

- guidance

m/A3 m/A3

Not
Applicable.

Not Applicable.

Power frequency
(50/60 Hz)
magnetic field
IEC 61000-4-8

Power frequency magnetic fields
should be at levels characteristic of
a typical location in a typical
commercial or hospital environment.

Note: UT is the A.C. mains voltage prior to application of the test level.

Voltage dips,
short
interruptions
and voltage
variations on
power supply
inputlines
IEC 61000-4-11

<5 %

U

T

(>95 % dip
in

U

T

)

for 0.5 cycle

40 %

U

T

(60 % dip in

U

T

)

for 5 cycles

70 %

U

T

(30 % dip in

U

T

)

for 25 cycles

<5 %

U

T

(>95 % dip in

U

T

)

for 5 sec.

29

GUIDANCE AND MANUFACTURER’S DECLARATION

Portable and mobile RF
communications equipment should
be used no closer to any part of the
ReliOnTM HEM-741CRELN4
including cables, than the
recommended separation distance
calculated from the equation
appropriate to the frequency of the
transmitter.

Recommend separation distance

Not Applicable.

d = 1.2
80 MHz to 800 MHz
d = 2.3
800 MHz to 2.5 GHz

Not
Applicable.

3 V/m

3 V rms
150 kHz to
80 MHz
3 V/m
80 MHz to

2.5 GHz

Conducted RF
IEC 61000-4-6

Radiated RF
IEC 61000-4-3

Immunity test

IEC 60601
test level

Compliance
level

Electromagnetic environment

- guidance

P

P

ReliOnTM HEM-741CRELN4 is intended for use in the electromagnetic environment
specified below. The customer or the user of this ReliOnTM HEM-741CRELN4 should
assure that it is used in such environment.

Guidance and manufacturer’s declaration - electromagnetic immunity

30

GUIDANCE AND MANUFACTURER’S DECLARATION

a

Field strengths from fixed transmitters, such as base stations for radio (cellular/
cordless) telephones and land mobile radio, AM and FM radio broadcast, and TV
broadcast cannot be predicted theoretically with accuracy. To assess the
electromagnetic environment due to fixed RF transmitters, an electromagnetic site
survey should be considered. If the measured field strength in the location in which
the ReliOnTM HEM-741CRELN4 is used exceeds the applicable RF compliance level
above, the ReliOnTM HEM-741CRELN4 should be observed to verify normal
operation. If abnormal performance is observed, additional measures may be
necessary, such as reorienting or relocating the ReliOnTM HEM-741CRELN4.

b

Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 V/m.

Note1: At 80 MHz and 800 MHz, the higher frequency range applies.
Note2: These guidelines may not apply in all situations. Electromagnetic propagation

is affected by absorption and reflection from structures, objects, and people.

Immunity test

IEC 60601
test level

Compliance
level

Electromagnetic environment

- guidance

where P is the maximum output
power rating of the transmitter in

watts (W) according to the

transmitter manufacturer and d is
the recommended separation
distance in meters (m).
Field strengths from fixed RF
transmitters as determined by an
electromagnetic site survey,

a

should be less than the compliance
level in each frequency range.

b

Interference may occur in the
vicinity of equipment marked with
the following symbol:

31

80 MHz to 800 MHz 800 MHz to 2.5GHz

150 kHz to 80 MHz

Not Applicable.

d = 1.2

P

d = 2.3

P

Recommended separation distance between portable and mobile RF

communications equipment and the ReliOn

TM

HEM-741CRELN4

ReliOn

TM

HEM-741CRELN4 is intended for use in an electromagnetic environment in

which radiated RF disturbances are controlled. The customer or the user of this ReliOn

TM

HEM-741CRELN4 can help prevent electromagnetic interference by maintaining a
minimum distance between portable and mobile RF communications equipment
(transmitters) and the ReliOnTM HEM-741CRELN4 as recommended below, according
to the maximum output power of the communications equipment.

Output Power
of Transmitter
in Watt

Separation distance according to frequency of transmitter in meter

For transmitters rated at a maximum output power not listed above, the recommended
separation distance d in meters (m) can be estimated using the equation applicable to
the frequency of the transmitter, where P is the maximum output power rating of the

transmitter in watts (W) according to the transmitter manufacturer.

Note: At 80 MHz and 800 MHz, the separation distance for the higher frequency
range applies.
Note: These guidelines may not apply in all situations. Electromagnetic propagation is
affected by absorption and reflection from structures, objects, and people.

Not Applicable.

0.01

0.1

1

10

100

0.12

0.38

1.2

3.8

12

0.23

0.73

2.3

7.3

23

GUIDANCE AND MANUFACTURER’S DECLARATION

32

LIMITED WARRANTY

Your ReliOnTM BP200 Blood Pressure Monitor, Model # HEM-741CRELN4, excluding
the arm cuff and batteries, is warranted to be free from defects in materials and
workmanship appearing within 5 years from the date of purchase, when used in
accordance with the instructions provided with the monitor. The arm cuff is warranted
to be free from defects in materials and workmanship appearing within one year from
the date of purchase when the monitor is used in accordance with the instructions
provided with the monitor. The above warranties extend only to the original retail
purchaser.

We will, at our option, replace without charge any monitor or arm cuff covered by the

above warranties. Replacement is our only responsibility and your only remedy under
the above warranties.

To obtain warranty service contact Customer Service by calling 1-855-776-0662 for the
address of Inspection center.

Enclose the Proof of Purchase. Include a letter, with your name, address, phone
number, and description of the specific problem. Pack the product carefully to prevent
damage in transit. Because of possible loss in transit, we recommend insuring the
product with return receipt requested.

THE FOREGOING IS THE SOLE WARRANTY PROVIDED BY RELION IN
CONNECTION WITH THIS PRODUCT, AND RELION HEREBY DISCLAIMS
ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. IMPLIED WARRANTIES AND OTHER TERMS THAT MAY BE
IMPOSED BY LAW, IF ANY, ARE LIMITED IN DURATION TO THE PERIOD
OF THE ABOVE EXPRESS WARRANTY.

RELION

SHALL NOT BE LIABLE FOR LOSS OF USE OR ANY OTHER
SPECIAL, INCIDENTAL, CONSEQUENTIAL OR INDIRECT COSTS,
EXPENSES OR DAMAGES.

33

LIMITED WARRANTY

This warranty provides you with specific legal rights, and you may have other rights
which vary from state to state.

Some states do not allow limitations on how long an implied warranty lasts, so the
above limitation may not apply to you. Some states do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitation or exclusion
may not apply to you.

FOR CUSTOMER SERVICE

Call toll free: 1-855-776-0662

34

SPECIFICATIONS

Model:

Display:

Measurement Range:

Accuracy/Calibration:

Inflation:

Deflation:

Rapid Air Release:

Measurement Method:

IP classification:

Power Source:

Battery Life:

Operating Temperature /Humidity:

Storage Temperature
/Humidity/Air Pressure:

Main Unit Weight:

Main Unit Dimensions:

Cuff Size:

Cuff Circumference:

Memory:

Contents:

Optional Accessories:

HEM-741CRELN4 (HEM-8724-WM)

LCD Digital Display

Pressure: 0 to 299 mmHg, Pulse: 40 beats/min to 180 bearts/min.

Pressure: ±3 mmHg or 2% of reading
Pulse: ±5% of reading

Fuzzy-logic controlled by electric pump

Automatic pressure release valve

Automatic exhaust valve

Oscillometric method

IP 20

1.5 V 4 "AA" batteries

Approximately 1000 uses with 4 new alkaline batteries

50ºF to 104ºF (10ºC to 40ºC) /15% RH to 90% RH

-4ºF to 140ºF (-20ºC to 60ºC) /10% RH to 95% RH
700 hPa to 1060 hPa

Approximately 12 3/10 oz. (350 g)
not including batteries

Approximately 6"(l) × 4 3/5"(w) × 3 1/2" (h)
(150 mm × 118 mm × 90 mm)

Approximately 5 3/4" × 23 1/2" (air tube: 29 1/2")
(145 mm × 594 mm (air tube: 750 mm))

Fits arm circumferences 9" to 17"

(22 cm to 42 cm)

Up to 60 readings per user

Main Unit, Wide Range Cuff, 4 "AA" Alkaline Batteries,
Instruction Manual, and Quick Start Guide

Arm cuff

NOTE: These specifications are subject to change without notice.

=Type BF

35

Distributed by Wal-Mart Stores, Inc., Bentonville, AR 72716

Manufactured for OMRON HEALTHCARE Co. Ltd.
53, Kunotsubo, Terado-cho, Muko, Kyoto, 617-0002 JAPAN

© 2014 Wal-Mart Stores, Inc.

Made in Vietnam

9701203-7A