Quadra-Fire 31ST-ACC, 31M-ACC-NT, 31M-ACC-GT, 31M-ACC-MBK User Manual

3100 WOOD STOVE SERIES

Advanced Combustion Control (ACC)

Owner’s Manual

Installation and Operation

Models:

31M-ACC-MBK

31M-ACC-GT 31M-ACC-NT

31ST-ACC

Beaverton

Oregon USA

ested and

Listed by

OMNI- Test Laboratories, I nc.

Step Top Uni-Body Model

(Pedestal Model Shown)

DO NOT DISCARD THIS MANUAL

•

Important operating and maintenance instructions included.

• Read, understand and follow these instructions for safe installation and operation.

WARNING

If the information in these instructions is not followed exactly, a ﬁ re may result causing property damage, personal injury, or death.

• Do not store or use gasoline or other ﬂ am- mable vapors and liquids in the vicinity of this or any other appliance.

• Do not overﬁ re - If heater or chimney con- nector glows, you are overﬁ ring. Overﬁ ring will void your warranty.

• Comply with all minimum clearances to combustibles as speciﬁ ed. Failure to comply may cause house ﬁ re.

CAUTION

• Keep children away.

• CAREFULLY SUPERVISE children in same room as

• Alert children and adults to hazards of high

• Do NOT operate with protective barriers removed or

• Keep clothing, furniture, draperies and other

Millennium Model

• Leave this manual with party responsible for use and operation.

HOT! DO NOT TOUCH. SEVERE BURNS MAY RESULT. CLOTHING IGNITION MAY RESULT.

Glass and other surfaces are hot during operation and cool down.

appliance.

temperatures.

door open.

combustibles away.

WARNING

DO NOT

DISCARD

Installation and service of this appliance should be performed by qualiﬁ ed personnel. Hearth & Home Technologies recommends NFI certiﬁ ed professionals, or technicians supervised by an NFI certiﬁ ed professional.

www.quadraﬁ re.com

7033-277C

Fire Risk.

For use with solid wood fuel only. Other fuels may overﬁ re and generate

poisonous gases (i.e. carbon monoxide).

WARNING

March 2, 2007

3100 Wood Stove Series (ACC)

and Welcome to the Quadra-Fire Family!

Hearth & Home Technologies welcomes you to our tradition of excellence! In choosing a Quadra-Fire appliance, you have our assurance of commitment to quality , durability, and performance.

This commitment begins with our research of the market, including ‘Voice of the Customer’ contacts, ensuring we make products that will satisfy your needs. Our Research and Development facility then employs the world’s most advanced technology to achieve the optimum operation of our stoves, inserts and ﬁ replaces. And yet we are old- fashioned when it comes to craftsmanship. Each unit is

With warm regards,

meticulously fabricated and gold and nickel surfaces are hand-ﬁ nished for lasting beauty and enjoyment. Our pledge to quality is completed as each model undergoes a quality control inspection. From design, to fabrication, to shipping: Our guarantee of quality is more than a word, it’s QuadraFire tradition, and we proudly back this tradition with a Limited Lifetime Warranty.

We wish you and your family many years of enjoyment in the warmth and comfort of your hearth appliance. Thank you for choosing Quadra-Fire.

___________________________

Alan Trusler

Senior

Vice President

Dealer Channel

___________________________

Dan Henry

Vice President

Advanced Technolgies

_________________________

Jason Olmstead Vice President &

General Manager

SAMPLE OF SERIAL NUMBER / SAFETY LABEL

LOCATION: BACK OF APPLIANCE

___________________________

Steve Tate

Quadra-Fire

Brand Manager

Serial No.

Model Name

Test Lab & Report No.

Page 2

SAMPLE

7033-277C

Mfg. Date

March 2, 2007

3100 Wood Stove Series (ACC)

TABLE OF CONTENTS

Section 1: Listing and Code Approvals

A. Appliance Certiﬁ cations ......................4

B. Mobile Home Approved ......................4

C. Glass Speciﬁ cations ............................4

D. BTU & Efﬁ ciency Speciﬁ cations ..........4

Section 2: Getting Started

A. Design, Installation & Location

Considerations ....................................5

B. Fire Safety ..........................................5

C. Negative Pressure ..............................6

D. Flue Draft Considerations ...................7

E. Venting Systems .................................7

F. Tools and Supplies Needed................7

G. Inspect Appliance & Components.......7

H. Typical Stove System .........................8

Section 3: Dimensions & Clearances

A. Appliance Dimensions ........................9-10

B. Clearances to Combustibles ...............11

Section 4: Installation Consideration

A. Hearth Requirements .........................12-13

B. Outside Air ..........................................14

C. Blower Installation ...............................15

Section 8: Operating Instructions (Cont’d)

H. Blower Operating Instructions .............29

I. Opacity (Smoke) .................................29

J. Overﬁ ring ............................................29

K. Frequently Asked Questions...............30

Section 9: Maintaining & Servicing Appliance

A. General Maintenance & Cleaning .......31-32

B. Glass Replacement .............................32

C. Firebrick Replacement ........................33

D. Bafﬂ e Removal ....................................34

E. Snap Disc Replacement .....................34

F. Tube Channel Replacement ...............35

Section 10: Troubleshooting ........................36-37

Section 11: Reference Material

A. Exploded Drawings .............................38-40

B. Service Parts & Accessories...............41-43

C. Service & Maintenance Log ................44

D. Homeowner’s Notes ...........................45-46

E. Warranty Policy ...................................47

F. Contact Information .............................48

Section 5: Chimney Requirements

A. Venting Components ..........................16

B. Chimney Systems ...............................16-18

C. Installing Chimney Components .........18

D. Chimney Termination Requirements ..19

E. 2-10-03 Rule ........................................19

Section 6: Mobile Home ...............................20

Section 7: Appliance Set-Up

(ARS) Installation ...............................21-22

B. Leg Kit & Ash Removal System

A. Pedestal & Ash Removal System

(ARS) Installation...........................23

C. Door Handle Assembly .......................24

D. Blower Speed Adjustment ..................24

Section 8: Operating Instructions

A. Fire Safety ...........................................25

B. Wood Selection & Storage ..................25

C. Burning Process ..................................25-26

E. Air Controls .........................................26-27

F. Burn Rates & Operating Efﬁ ciency .....27

G. Building A Fire .....................................28

Automatic Combustion Control (ACC)

....26

March 2, 2007

7033-277C

Page 3

3100 Wood Stove Series (ACC)

Listing and Code Approvals

A. Appliance Certiﬁ cation

Model:

Laboratory: OMNI Test Laboratories, Inc. Report No & Date: Type: Standard: UL1482 and ULC S627 and (UM)

The Quadra-Fire 3100 Series Wood Stove (ACC) meets the U.S. Environmental Protection Agency’s 1990 particulate emission standards.

3100 Millennium & Step Top (ACC) Uni-Body

061-S-66-6 Wood Stove

84-HUD, Mobile Home Approved.

B. Mobile Home Approved

This appliance is approved for mobile home installations when not installed in a sleeping room and when an outside combustion air inlet is provided. The structural integrity of the mobile home ﬂ oor , ceiling, and walls must be maintained. The appliance must be properly grounded to the frame of the mobile home and use only listed double-wall connector pipe. Outside Air Kit, part OAK-ACC must be installed in a mobile home installation

D. BTU & Efﬁ ciency Speciﬁ cations

EPA Certiﬁ ed: Efﬁ ciency: BTU Output: Heating Capacity: Vent Size: Firebox Size: Max Wood Length: Fuel: Shipping Weight:

NOTE: Hearth & Home Technologies, manufacturer of

this appliance, reserves the right to alter its products, their speciﬁ cations and/or price without notice.

1.1 grams per hour

79.51%

11,800 to 32,000

up to1,800 sq ft

6 inches

2 cubic feet

18 inches

Cord Wood

325 lbs

C. Glass Speciﬁ cations

This stove is equipped with 5mm ceramic glass. Replace glass only with 5mm ceramic glass. Please contact your dealer for replacement glass.

NOTE: This installation must conform with local codes. In the absence of local codes you must comply with the UL1482,

(UM) 84-HUD and NPFA211 in the U.S.A. and the ULC S627 and CAN/CSA-B365 Installation Codes in Canada.

Page 4

7033-277C

March 2, 2007

3100 Wood Stove Series (ACC)

. Design, Installation & Location Considerations

Consideration must be given to:

• Safety

• Convenience

• Trafﬁ c ﬂ ow

• Chimney and chimney connector required It is a good idea to plan your installation on paper, using exact

measurements for clearances and ﬂ oor protection, before actually beginning the installation. If you are not using an existing chimney, place the appliance where there will be a clear passage for a factory-built listed chimney through the ceiling and roof.

We recommend that a qualiﬁ ed building inspector and your insurance company representative review your plans before and after installation

If this appliance is in an area where children may be near it is recommended that you purchase a decorative barrier to go in front of the appliance. away while it is operating and do not let anyone operate this appliance unless they are familiar with these operating instructions.

Service / Maintenance Tip:

In order to replace the tube channel a clearance of 19 inches (483mm) is required on the right side of stove in order to remove the tubes with the stove in place. If space is not available, the stove will have to be disconnected from the chimney to proceed with the tube replacement. See

page 35.

Getting Started

Remember to always keep children

CAUTION

Check building codes prior to installation.

• Installation MUST comply with local, regional, state and national codes and regulations.

• Consult insurance carrier, local building, ﬁ re ofﬁ cials or authorities having jurisdiction about restrictions, installation inspection, and permits.

WARNING

B. Fire Safety

To provide reasonable ﬁ re safety, the following should be given serious consideration:

1. Install at least one smoke detector on each ﬂ oor of your home to ensure your safety. They should be located away from the heating appliance and close to the sleeping areas. Follow the smoke detector manufacturer’s placement and installation instructions, and be sure to maintain regularly.

2. A conveniently located Class A fire extinguisher to contend with small fires resulting from burning embers.

3. A practiced evacuation plan, consisting of at least two escape routes.

4. A plan to deal with a chimney ﬁ re as follows:

In the event of a chimney ﬁ re:

a. Notify ﬁ re department b. Prepare occupants for immediate evacuation. c. Close all openings into the stove. d. While awaiting ﬁ re department, watch for ignition

of adjacent combustibles from overheated stove pipe, hot embers or sparks from the chimney.

WARNING

Fire Risk.

Hearth & Home Technologies disclaims any responsibility for, and the warranty will be voided by, the following actions:

• Installation and use of any damaged appliance.

• Modiﬁ cation of the appliance.

• Installation other than as instructed by Hearth & Home Technologies.

• Installation and/or use of any component part not approved by Hearth & Home Technologies.

• Operating appliance without fully assembling all components.

• Operating appliance without legs attached (if supplied with unit).

• Do NOT Overﬁ re - If appliance or chimney connector glows, you are overﬁ ring.

Any such action that may cause a ﬁ re hazard.

Asphyxiation Risk.

March 2, 2007

• Do NOT connect this unit to a chimney ﬂ ue servicing another appliance.

• Do NOT connect to any air distribution duct or system.

May allow ﬂ ue gases to enter the house.

7033-277C

WARNING

Fire Risk.

• Do not operate appliance before reading and understanding operating instructions.

• Failure to operate appliance properly may cause a house ﬁ re.

Page 5

3100 Wood Stove Series (ACC)

C. Negative Pressure

Draft is the pressure difference needed to vent appliances successfully. Considerations for successful draft include:

• Preventing negative pressure

• Location of appliance and chimney Negative pressure results from the imbalance of air avail-

able for the stove to operate properly . Causes for this imbalance include:

• Exhaust fans (kitchen, bath) etc.)

• Range hoods

• Combustion air requirements for furnaces, water heaters and other combustion appliances

• Clothes dryers

• Location of return-air vents to furnace or air conditioning

• Imbalances of HVAC air handling system

• Upper level air leaks

• Recessed lighting

• Attic hatch opening

• Duct leaks

To minimize the affects of negative air pressure the following must be considered:

• Install the outside air kit. Install the intake on the side of the house towards prevailing winds during the heating season.

• Ensure adequate outdoor air is supplied for combustion appliances and exhaust equipment.

• Ensure furnace and air conditioning return vents are not located in the immediate vicinity of the appliance,

• Avoid installing the appliance near doors, walkways or small isolated spaces.

• Recessed lighting should be of “sealed can” design; attic hatches weather stripped or sealed; and attic mounted duckwork and air handler joints and seams taped or sealed.

WARNING

Asphyxiation Risk.

Windward

Location

Not

Recommended

Outside Termination Cap

Marginal Location

Recommended

Location

• Negative pressure can cause spillage of combustion fumes, soot and carbon monoxide.

• Appliance needs to draft properly for safety.

Recommended

Location

Location NOT

Recommended

Leeward

Multi-level Roofs

Figure 6.1

Page 6

7033-277C

March 2, 2007

3100 Wood Stove Series (ACC)

D. Flue Draft Considerations

Location of the appliance and chimney will affect performance. As shown in Figure 6.1 on page 6 the chimney should:

• Be installed through the warm space enclosed by the building envelope. This helps to produce more draft, especially during lighting and die down of the ﬁ re.

• Penetrate the highest part of the roof. This minimizes the affects of wind turbulence and down drafts.

• Consider the appliance location in order to avoid ﬂ oor and ceiling attic joists and rafters.

Exterior conditions such as roof line, surrounding trees, prevailing winds and nearby hills can influence stove performance. Y our local dealer is the expert in your geographic area and can usually make suggestions or discover solutions that will easily correct your ﬂ ue problem.

o be sure that your appliance burns properly, the chimney draft (static pressure) should be approximately -.04 inch water column (W.C.) during a low burn and -.10 inch W.C. during a high burn, measured 6 inches (152mm) above the top of the appliance after one hour of operation at each burn setting.

NOTE: These are guidelines only, and may vary somewhat for individual installations.

E. Venting Systems

The venting system consists of a chimney connector (also known as stove pipe) and a chimney. These get extremely hot during use. Temperatures inside the chimney may exceed 2000°F (1 100°C) in the event of a creosote ﬁ re. To protect against the possibility of a house ﬁ re, the chimney connector and chimney must be properly installed and maintained. An approved thimble must be used when a connection is made through a combustible wall to a chimney . A chimney support package must be used when a connection is made through the ceiling to a prefabricated chimney. These accessories are absolutely necessary to provide safe clearances to combustible wall and ceiling material. Follow venting manufacturer’s clearances when installing venting system.

F. Tools And Supplies Needed

Before beginning the installation be sure that the following tools and building supplies are available.

Reciprocating saw Pliers Hammer Phillips Head Screwdriver Flat Blade Screwdriver Plumb Line Level Tape Measure

Framing Material Hi-Temp Caulking Material Gloves Framing Square Electric Drill & Bits (1/4”) Safety Glasses 1/2 in. - 3/4 in. length, #6 or #8 self drilling screws (need 3 per pipe section connection)

G. Inspect Appliance & Components and

Pre-Use Check List

1. Place the appliance in a location near the ﬁ nal installation area and follow the procedures below:

2. Open the appliance and remove all the parts and articles packed inside the Component Pack. Inspect all the parts and glass for shipping damage. Contact your dealer if any irregularities are noticed.

3. All safety warnings have been read and followed.

4. This Owner’s Manual has been read.

5. Floor protection requirements have been met.

6. Venting is properly installed.

7. The proper clearances from the appliance and chimney to combustible materials have been met.

8. The masonry chimney is inspected by a professional and is clean, or the factory built metal chimney is installed according to the manufacturer’s instructions and clearances.

9. The chimney meets the required minimum height.

10.

11. Plated surfaces have been wiped clean, if appli-

12. A power outlet is available nearby if installing

All labels have been removed from the glass door.

cable.

optional blower assembly.

March 2, 2007

WARNING

Asphyxiation Risk.

• Do NOT connect this unit to a chimney ﬂ ue servicing another appliance.

• Do NOT connect to any air distributon duct or system.

May allow ﬂ ue gases to enter the house.

7033-277C

WARNING

Fire Risk.

Inspect appliance and components for damage. Damaged parts may impair safe operation.

• Do NOT install damaged components.

• Do NOT install incomplete components.

• Do NOT install substitute components.

Report damaged parts to dealer.

Page 7

3100 Wood Stove Series (ACC)

H. Typical Stove Systems

Stove system with masonry chimney consists of:

• Stove

• Chimney Connector (stove pipe)

• Thimble

• Masonry Chimney

• Hearth Pad Floor Protection

Spark Arrestor Cap

1" (25mm) Clearance With Firestop

Ceiling Joist

Combustible Wall

Thimble, 12" (305mm) Of Brick

Floor Protector

Concrete Cap

Fireclay Flue Liner With Air Space

Rafter

Flashing

Eave

Sheathing

Outside Air Rear Vent

Outside Air Termination Cap

Stove system with prefabricated metal chimney consists of:

• Stove Chimney Connector

• (stove pipe)

• Thimble (for exterior chimney)

• Firestops

• Insulations Shields

• Storm Collar and Flashing

• Termination Cap

• Hearth Pad Floor Protection

Figure 8.1 Masonry Chimney

ListedTerminationCap

Roof Brace (if required)

Trim Collar on Inside Wall

Chimney Connector

Storm Collar

Flashing

Listed Chimney

Insulated " T "

Wall Support

Airtight Cleanout Door

Listed Termination Cap

Storm Collar

Flashing

Listed Chimney

Ceiling Support

Chimney Connector

Page 8

Floor Protector

7033-277C

Floor Protector

Figure 8.3 Interior Prefabricated ChimneyFigure 8.2 Exterior Prefabricated Chimney

March 2, 2007

3100 Wood Stove Series (ACC)

Dimensions and Clearances

A. Appliance Dimensions

NOTE: Flue Collar size is 6 inch (152mm) diameter (ID)

Millennium Model

30 in. (762mm)

9-15/16 in. (237mm)

15-1/16 in. (383mm)

25 in. (635mm)

10-15/16 in. (271mm)

18-15/16 in. (475mm)

12-1/2 in. (318mm)

14-15/16 in. (373mm)

Figure 9.1 Front View

26-11/16 in. (668mm)

24-5/16 in. (618mm)

16 in. (406mm)

6-11/16 in. (170mm)

11-1/2 in. (292mm)

March 2, 2007

Figure 9.2 Side View

20-3/4 in. (527mm)

7033-277C

Page 9

3100 Wood Stove Series (ACC)

Appliance Dimensions (Cont’d)

3100 Step Top Pedestal Model

25 in. (635mm)

12-1/2 in.

9-5/16 in. (237mm)

34-1/4 in. (870mm)

18 in.

(457mm

(318mm

)

3100 Step Top Leg Model

)

14-15/16 in.

(379mm)

10-15/16 in.

(278mm)

33-1/8 in. (841mm)

19-1/16 in.

(484mm)

15-1/16 in.

(383mm)

23-7/8 in. (606mm)

Figure 10.1

26-11/16 in.(678mm)

24-5/16 in. (618m m)

15-3/8 in. (391mm )

16 in. (406mm)

11- 1 /2 in.

(292mm)

Figure 10.3

3-11/16 in. (94mm)

6-11/16 in. (170mm)

Back of Stove to Glass

23-3/8 in. (594mm)

3-1/2 in. (89mm)

10-3/8 in. (264mm)

Figure 10.2

Page 10

20-3/4 in. (527mm)

Figure 10.4

7033-277C

21-1/8 in. (537mm)

March 2, 2007

B. Clearances to Combustibles (UL and ULC)

3100 Wood Stove Series (ACC)

BACKWALL / SIDEWALL

NOTE: Clearances may only be reduced by means

ALCOVE SIDE VIEW

approved by the regulatory authority having jurisdiction

90° OFF TOP UP & OUT CEILING CLEARANCE

CORNER INSTALLATION

MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS In Inches & (Millimeters)

NOTE: All "A" , "C" and "F" Dimensions are to the inside diameter of the flue collar.

A B C D E F G H

INSTALLATION: Full Vertical OR Horizontal with Minimum 2 FT Vertical Off Stove Top

SINGLE WALL PIPE

Flat Top Model 15.25 (387) 11.75 (298) 25.5 (648) 16 (406) 8 (203) 17 (432) 48 (1220) 12 (305) Step-Top Model 12 (305) 8.5 (216) 22 (559) 12.5 (318) 5.5 (140 14.5 (368) 48 (1220) 12 (305)

DOUBLE WALL PIPE Flat Top Model 10.5 (267) 6.5 (165) 22 (559) 13 (330) 6.5 (165) 15.5 (394) 48 (1220) 9 (229) Step-Top Model 10 (228) 6 (152) 20.5 (521) 11 (279) 4 (102) 13 (330) 48 (1220) 9 (229)

INSTALLATION: 90° Elbow Off Top of Stove Through Backwall

STOVE TO CEILING CLEARANCE

ALCOVE TOP VIEW

SINGLE WALL PIPE Flat Top Model 12 (305) 8.5 (216) 22 (559) 13 (330) 8 (203) 17 (432) 48 (1220) 12 (305) Step-Top Model 10 (254) 6 (152) 20.5 (521) 11 (279) 5.5 (140) 14.5 (368) 48 (1220) 12 (305)

DOUBLE WALL PIPE Flat Top Model 8 (203) 4.5 (114) 17.5 (445) 8.5 (216) 6.5 (165) 15.5 (394) 48 (1220) 9 (229) Step-Top Model 10 (254) 6 (152) 20.5 (521) 11 (279) 4 (102) 13 (330) 48 (1220) 9 (229)

INSTALLATION: ALCOVE factory-built Class "A" chimney, or a masonry chimney. (Mobile Home must be equipped with a spark arrestor). Maximum depth of Alcove shall be no more than 48 inches (1220mm) with a minimum height of 48 inches (1220mm) to top of unit, and the referenced clearances.

*In Canada must comply with CAN/ULC-S269 M87 for the 650

DOUBLE WALL PIPE

Flat Top Model 11.75 (298) 8.25 (210) 23.5 (597) 14.5 (368) N/A N/A 48 (1220) * Step-Top Model 10 (254) 6.5 (152) 20.5 (521) 11 (279) N/A N/A 48 (1220) *

* SEE PIPE MANUFACTURERS CLEARANCES - NOT TESTED

WARNING

Fire Risk.

March 2, 2007

• Comply with all minimum clearances to combustibles as speciﬁ ed.

• Failure to comply may cause house ﬁ re.

Six inch (6") (152mm) diameter listed Double Wall air insulated connector pipe with UL103 HT* listed

C Factory-built chimney.

SERVICE / MAINTENANCE TIP

In order to replace the tube channel assembly a clearance of 19 inches (483mm) is required on the right side of stove in order to remove the tubes with the stove in place. If space is not available, the stove will have to be disconnected from the chimney to proceed with the tube replacement.

7033-277C

Page 11

3100 Wood Stove Series (ACC)

Installation

A. Hearth Protection Requirements

FLOOR PROTECTION: Floor protector must be non-com-

bustible material, extending beneath heater and to the front, sides and rear as indicated. The ﬂ oor must be non-com- bustible or otherwise adequately protected from radiant heat given off by the unit and from sparks and falling embers. A layer of thin brick or ceramic tile over a combustible ﬂ oor is not sufﬁ cient.

For the Millennium Model In US installations, i essary to install a ﬂ oor protector of a minimum of 3/8 inch (9.5mm) thick metal clad millboard or equivalent a minimum of 16

inches (406mm) in front of glass and 8 inches (203mm) to both sides of the fuel loading door. Open the door and measure 8 inches (203mm) from the side edge of the opening in the face of the appliance. *See exception.

t is nec-

Millennium Model

In Canada, similar ﬂ oor protection must be provided 18 inches (457mm) in front and 8 inches (203mm) from the sides and rear of the stove. *See exception.

*EXCEPTION: Non-combustible ﬂ oor protections must extend beneath the ﬂ ue pipe when installed with horizontal venting and extend 2 inches (51mm) beyond each side.

See Figure 12.4.

WARNING

Fire Risk.

• Hearth pads must be installed exactly as specified.

High temperatures or hot embers may ignite concealed combustibles.

Figure 12.1

203mm

(8 in.)

4-7/8 in.

Fuel loading door

16" from glass

31-5/8 in. minimum

203mm (8 in.)

3-1/8 in."

8 in.

USA

203mm

(8 in.)

39-5/8 in. minimum

1260mm (49-5/8 in.) minimum

49-7/8 in.

Figure 12.3

49-7/8 in.

27-5/8 in.

USA required

Canada recommended

27-5/8 in.

USA

Figure 12.2

Page 12

457mm (18 in.)

1041mm (41 in.)

minimum

CANADA

7033-277C

Must extend 2 in. (51mm) beyond

each side of pipe (shaded area)

Figure 12.4

March 2, 2007

3100 Wood Stove Series (ACC)

Step-Top Uni-Body Model

For the Step T op Pedestal Model In US installations, i

t is necessary to install a ﬂ oor protector of a minimum of 3/8 inch (9.5mm) thick metal clad millboard or equivalent a minimum of 16

clearances and horizontal venting exception.

4-3/4 in.

Fuel loading door

16 in. from glass

3-1/4 in.

39-5/8 in. minimum

8 in.

USA

31-5/8 in.

minimum

Figure 13.1

For the Step T op Leg Model In US installations, i

t is necessary to install a ﬂ oor protector of a minimum thickness of 1-1/4 inch (32mm) or 1/2 inch of “k” value of 0.84 thick metal clad millboard or equivalent a minimum of 16

horizontal venting exception.

8 in.

49-7/

8 in.

9-7/

Figure 13.3

27-5/8 in.

USA

USA required

Canada recommended

203mm (8 in.)

203mm

(8 in.)

203mm

(8 in.)

1254mm (49-3/8 in.) minimum

457mm (18 in.)

CANADA

1041mm (41 in.)

minimum

Figure 13.2

NOTE:

• Illustrations and photos reﬂ ect typical installations and are FOR DESIGN PURPOSES ONLY.

Figure 13.4

Must extend 2 in. (51mm) beyond

each side of pipe (shaded area)

• Illustrations/diagrams are not drawn to scale.

• Actual installation may vary due to individual design preference

• Hearth & Home Technologies reserves the right to alter its products.

March 2, 2007

7033-277C

Page 13

3100 Wood Stove Series (ACC)

B. Outside Air Kit Installation

A source of air (oxygen) is necessary in order for combustion to take place. Whatever combustion air is consumed by the ﬁ re must be replaced. Air is replaced via air leak- age around windows and under doors. In homes that have tightly sealed doors and windows, an outside air source is needed. An optional Outside Air Kit is avail

Included in OAK-ACC: Termination cap, (2) wire ties, flex

adapter, and fasteners

Included in SRV7033-041: Cover plate and sealing rope (see

Floor Installation Alternative below,

Figure 14.2)

Items Needed for Installation (not supplied)

• 4 inch ﬂ ex aluminum pipe, or if using alternate material, then it shall be made from durable, non-combustible, heat resistant material up to 350oF. Cut the pipe to the required length for your installation.

• Phillips head screw driver

• Silicone sealant

• Drills and saws necessary for cutting holes through the wall or ﬂ ooring in your home.

able.

WARNING

Fire Risk. Asphyxiation Risk.

Do not draw outside combustion air from:

• Wall, ﬂ oor or ceiling cavity

• Enclosed space such as an attic or garage

• Close proximity to exhaust vents or chimneys

Fumes or odor may result

WARNING

Asphyxiation Risk.

Outside air inlet must be located to prevent blockage from:

• Leaves

• Snow or ice

• Other debris Block may cause combustion air starvation Smoke spillage may set off alarms or irritate sensi-

tive individuals.

1. Remove all materials from packing box.

2. Using a #2 Phillips screw driver attach the ﬂ ex adapter to the stove using 4 screws. Figure 14.1

Remove circular” knock-out” in the base of the pedestal.

4. Floor & Rear Installation: Cut a 4 inch (102mm) hole in outside wall or ﬂ oor to accommodate outside air piping. Use 4 inch (102mm) aluminum metal ﬂ ex or rigid piping to directly connect outside air to appliance intake. Use the supplied termination cap with a rodent screen. Seal between the wall (or ﬂ oor) and the pipe with silicone to prevent moisture penetration.

Flex Adapter

Wire Tie

Remove circular “knock-out” in base of pedestal.

Flex Line

Wire Tie

WARNING

Asphyxiation Risk.

Length of outside air supply duct shall NOT exceed the length of the vertical height of the exhaust ﬂ ue.

• Fire will not burn properly

• Smoke spillage occurs when door is opened due

to air starvation.

5. Floor Installation Alternative: In some instances you may not be able to install the ﬂ ex pipe as show in Figure

14.1. If that is the case, you will need to order SRV7033041 which includes a cover plate and sealing rope as shown in Figure 14.2. The goal is to seal the pedestal so no room air can leak into the pedestal.

Terminati Cap

Rope to Seal Pedestal

Cover Plate

Figure 14.1 - Floor & Rear Installation

Page 14

7033-277C

Figure 14.2 - Floor Installation Alternative

March 2, 2007

Do not remove

C. Blower (Optional)

1. Remove the 3 bolts (1/4”-20 Phillips head) on the outer skin at the bottom rear of appliance.

2. Align holes in mounting ﬂ ange of blower with bolt holes in appliance. Blower should be positioned at bottom of rear outer skin as shown in Figure 15.1.

3. Re-insert and tighten bolts, securing blower onto outer wall of appliance.

Place the bracket containing the snap disc and magnet

under the bottom left rear corner as shown in Figure 15.1.

See page 29 for detailed operating instructions for the

blower and snap disc.

3100 Wood Stove Series (ACC)

CAUTION

Shock Risk.

• Do NOT remove grounding prong from plug.

• Plug directly into properly grounded 3 prong receptacle.

• Route cord away from appliance.

•

Do NOT route cord under or in front of appliance.

Secure wires with wire tie.

Snap Disc Bracket with Magnet

FAN

HIGH

MANUAL

AUTO

OFF

LOW

MANUAL: Over-rides the Snap Disc

AUTO: Fan will turn ON/OFF Automatically by the Snap Disc

Controls the Fan Speed

Figure 15.1

March 2, 2007

7033-277C

Page 15

+ 33 hidden pages