Remote Control Keys V2.3
2010-12-01
Autor
Primare AB
1
Product:
Page Model
3 A20 / I20 / I21
4 A30.1 / I30
5 D20 / D30.2
6 Pre30
7 T21 / T22 / T30
8 SP31.7 / SPA20
9 SP31 / SPA21
10 V10, V20, V25
11 DVD30
13 P30
14 DVD26
16 CD21 /CD31
17 Master Delay Box
18 T23
20 Cdi10
22 DVDi10
24 SPA22/SP32
26 CD32
27 I32
28 History
2
A20 / I20 / I21 Remote Control Commands.
RC5 address = 20 (0x14)
bits:
0x0500 = 0000 0101 0000 0000 (=1280)
xxxx tsss ssdd dddd
(s ssss = 1 0100 = 0x14 = 20)
x=not used
t=toggle bit
s=system bits (address)
d=command (VALUE below)
short press (default) = 1 command.
long press = 3 consecutive identical commands
Key Dec. Value Hex. Value Action
standby 12 (0x0c) Standby ON (common)
standby 1 (0x01) Standby ON (unique)
operate 2 (0x02) Operate (Standby OFF)
step up 30 (0x1e) Next input
step down 31 (0x1f) Previous input
input mode 26 (0x1a) Toggle input mode (balance, master volume)
mute 49 (0x31) Toggle mute on/off
plus 16 (0x10) Increase/change master volume and balance
minus 17 (0x11) Decrease/change master volume and balance
dim 10 (0x0a) Toggle display on/off
1 60 (0x3c) Used for main input selection
2 61 (0x3d) Used for main input selection
3 62 (0x3e) Used for main input selection
4 63 (0x3f) Used for main input selection
For complete command, just add system address value 1280 with key value 1 (for standby) = 1281
(0x0501).
3
A30.1 / I30 Remote Control Commands.
RC5 address = 20 (0x14)
bits:
0x0500 = 0000 0101 0000 0000 (=1280)
xxxx tsss ssdd dddd
(s ssss = 1 0100 = 0x14 = 20)
x=not used
t=toggle bit
s=system bits (address)
d=command (VALUE below)
short press (default) = 1 command.
long press = 3 consecutive identical commands
Note !. Commands in Red Require Firmware update for use on A30.1 and some I30.
Key Dec. Value Hex. Value Action
standby 12 (0x0c) Standby ON (common) (with d20/d30))
standby 1 (0x01) Standby ON (unique)
operate 2 (0x02) Operate (Standby OFF)
step up 30 (0x1e) Next input
step down 31 (0x1f) Previous input
input mode 26 (0x1a) Toggle input mode (balance, master volume)
mute 49 (0x31) Toggle mute on/off
plus 16 (0x10) Increase/change master volume and balance
minus 17 (0x11) Decrease/change master volume and balance
dim 10 (0x0a) Toggle display on/off
1 60 (0x3c) Used for main input selection
2 61 (0x3d) Used for main input selection
3 62 (0x3e) Used for main input selection
4 63 (0x3f) Used for main input selection
5 3 (0x03) Used for main input selection
6 4 (0x04) Used for main input selection
For complete command, just add system address value 1280 with key value 12 (for standby) = 1292
(0x050c).
4
D20/D30.2 Remote Control Commands.
RC5 address = 20 (0x14)
bits:
0x0500 = 0000 0101 0000 0000 (=1280)
xxxx tsss ssdd dddd
(s ssss = 1 0100 = 0x14 = 20)
x=not used
t=toggle bit
s=system bits (address)
d=command (VALUE below)
short press (default) = 1 command.
long press = 3 consecutive identical commands
Key Dec. Value Hex. Value Action
Open 45 (0x2d)
play 53 (0x35) play/pause
stop 54 (0x26)
standby 12 (0x0c) long press = Standby ON, any other key = Operate
operate 58 (0x3a)
dim 10 (0x0a)
next_track 32 (0x20)
ff 52 (0x34)
prev_track 33 (0x21)
rew 50 (0x32)
plus10 47 (0x2f)
time 11 (0x0b)
a_b 59 (0x3b)
repeat 29 (0x1d)
mem 41 (0x29)
1 13 (0x0d)
2 14 (0x0e)
3 15 (0x0f)
4 18 (0x12)
5 19 (0x13)
6 20 (0x14)
7 21 (0x15)
8 22 (0x16)
9 23 (0x17)
0 24 (0x18)
check 25 (0x19)
clear 27 (0x1b)
shuffle 28 (0x1c)
intro 34 (0x22)
auto_space 35 (0x23)
play2 36 (0x24) only play
pause 37 (0x25) only pause
For complete command, just add system address value 1792 with key value 50 (for standby) = 1842
(0x0732).
5
Pre30 Remote Control Commands.
RC5 address = 24 (0x18)
bits:
0x0600 = 0000 0110 0000 0000 (=1536)
xxxx tsss ssdd dddd
(s ssss = 1 1000 = 0x18 = 24)
x=not used
t=toggle bit
s=system bits (address)
d=command (VALUE below)
short press (default) = 1 command.
long press = 3 consecutive identical commands
Key Dec. Value Hex. Value Action
standby 50 (0x32) Standby ON
step up 30 (0x1e) Next input (surround/record/main)
step down 31 (0x1f) Previous input (surround/record/main)
input level 38 (0x26) toggle input mode (input level/master volume)
balance 26 (0x1a) toggle input mode (balance, master volume)
mute 49 (0x31) Toggle mute on/off
plus 16 (0x10) Increase/change master volume, balance, input level
minus 17 (0x11) Decrease/change master volume, balance, input level
dim 10 (0x0a) Toggle display on/off
mode 42 (0x2a) Toggle surround mode on/off
record 48 (0x30) Toggle input mode record input path/main input path
operate 58 (0x3a) Operate (Standby OFF)
select 43 (0x2b) Reserved
1 13 (0x0d) Used for main input selection
2 14 (0x0e) Used for main input selection
3 15 (0x0f) Used for main input selection
4 18 (0x12) Used for main input selection
5 19 (0x13) Used for main input selection
6 20 (0x14) Used for main input selection
7 21 (0x15) Used for main input selection
8 22 (0x16) Used for main input selection
9 23 (0x17) Used for main input selection
0 24 (0x18) Used for main input selection
10 47 (0x2f) Used for main input selection
For complete command, just add system address value 1536 with key value 50 (for standby) = 1586
(0x0632).
6
T21 / T22 / T30 Remote Control Commands.
RC5 address = 16 (0x10)
bits:
0x0400 = 0000 0100 0000 0000 (=1024)
xxxx tsss ssdd dddd
(s ssss = 1 0000 = 0x10 = 16)
x=not used
t=toggle bit
s=system bits (address)
d=command (VALUE below)
short press (default) = 1 command.
long press = 3 consecutive identical commands
Key Dec. Value Hex. Value Action
operate 1 (0x01) Operate (Standby OFF / STANDBY ON?)
display 2 (0x02)
preset/tune 3 (0x03)
antenna 4 (0x04)
blend 5 (0x05)
if 6 (0x06)
mono 7 (0x07)
scan up 8 (0x08)
scan down 9 (0x09)
preset 1 10 (0x0a)
preset 2 11 (0x0b)
preset 3 12 (0x0c)
preset 4 13 (0x0d)
preset 5 14 (0x0e)
preset 6 15 (0x0f)
preset 7 16 (0x10)
preset 8 17 (0x11)
preset 9 18 (0x12)
store 19 (0x13)
preset up 20 (0x14)
preset down 21 (0x15)
dim 22 (0x16)
For complete command, just add system address value 1024 with key value 1 (for operate) = 1025 (0x0401).
7
SP31.7 / SPA20 Remote Control Commands.
RC5 address = 28 (0x1c)
bits:
0x0700 = 0000 0111 0000 0000 (=1792)
xxxx tsss ssdd dddd
(s ssss = 1 1100 = 0x1c = 28)
x=not used
t=toggle bit
s=system bits (address)
d=command (VALUE below)
short press (default) = 1 command.
long press = 3 consecutive identical commands
Key Dec. Value Hex. Value Action
standby 50 (0x32) long press = Standby ON
operate 58 (0x3a) Operate (Standby OFF)
step up 16 (0x10) In menus: previous row
Other: Next input
step down 17 (0x11) In menus: next row
Other: Previous input
input mode 26 (0x1a) toggle input mode (balance, center, side, rear, sub, master)
mute 49 (0x31) Toggle mute on/off
plus 30 (0x1e) In menus: menucommand "next"
Other: Increase/change master volume, balance, center, side,
rear, sub
minus 31 (0x1f) In menus: menucommand "previous"
Other: Decrease/change master volume, balance, center,
side, rear, sub
dim 10 (0x0a) Toggle display on/off
menu 38 (0x26) In menus: short press = previous menu
long press = leave menus
Other: Enter menus
mode 42 (0x2a) Next surround mode for 2ch inputs
select 43 (0x2b) In menus: menucommand "next"
record 48 (0x30) Next input for record path
(This command does not exist on SPA20)
1 13 (0x0d) Used for main input selection
2 14 (0x0e) Used for main input selection
3 15 (0x0f) Used for main input selection
4 18 (0x12) Used for main input selection
5 19 (0x13) Used for main input selection
6 20 (0x14) Used for main input selection
7 21 (0x15) Used for main input selection
8 22 (0x16) Used for main input selection
9 23 (0x17) Used for main input selection
0 24 (0x18) Used for main input selection
10 47 (0x2f) Used for main input selection
For complete command, just add system address value 1792 with key value 50 (for standby) = 1842
(0x0732).
8
SP31 / SPA21 Remote Control commands.
RC5 address = 28 (0x1c)
bits:
0x0700 = 0000 0111 0000 0000 (=1792)
xxxx tsss ssdd dddd
(s ssss = 1 1100 = 0x1c = 28)
x=not used
t=toggle bit
s=system bits (address)
d=command (VALUE below)
short press (default) = 1 command.
long press = 3 consecutive identical commands
Key Dec. Value Hex Value Action
standby 50 (0x32) Toggle Standby/Operate
operate 58 (0x3a) Operate (Standby OFF)
standby 59 (0x3b) Standby (Standby ON)
step up 16 (0x10) In menus: previous row
Other: Next input
step down 17 (0x11) In menus: next row
Other: Previous input
input mode 26 (0x1a) toggle input mode (balance, center, side, rear, sub, master)
mute 49 (0x31) Toggle mute on/off
plus 30 (0x1e) In menus: menucommand "next"
Other: Increase/change master volume, balance, center, side,
rear, sub
minus 31 (0x1f) In menus: menucommand "previous"
Other: Decrease/change master volume, balance, center,
side, rear, sub
dim 10 (0x0a) Toggle display on/off
menu 38 (0x26) In menus: short press = previous menu
long press = leave menus
Other: Enter menus
mode 42 (0x2a) Next surround mode for 2ch inputs
select 43 (0x2b) In menus: menucommand "next"
record 48 (0x30) Next input for record path
(This command does not exist on SPA21)
1 13 (0x0d) Used for main input selection
2 14 (0x0e) Used for main input selection
3 15 (0x0f) Used for main input selection
4 18 (0x12) Used for main input selection
5 19 (0x13) Used for main input selection
6 20 (0x14) Used for main input selection
7 21 (0x15) Used for main input selection
8 22 (0x16) Used for main input selection
9 23 (0x17) Used for main input selection
0 24 (0x18) Used for main input selection
10 47 (0x2f) Used for main input selection
For complete command, just add system address value 1792 with key value 50 (for standby) = 1842
(0x0732).
9
V10 / V20 / V25 Remote Control commands.
NEC system (32 bits)
SYSTEM CODE: 00FEH
Key Dec. Value Hex. Value Action
Open 65 0x41
Power 93 0x5D
Mute 73 0x49
Goto 77 0x4D
Menu 85 0x55
Title 88 0x58
1 64 0x40
2 68 0x44
3 80 0x50
Audio 92 0x5C
4 72 0x48
5 76 0x4C
6 84 0x54
Angle 27 0x1B
7 3 0x03
8 7 0x07
9 19 0x13
Subtitle 31 0x1F
0 15 0x0F
Subtitle_On 26 0x1A
Setp 2 0x02
Repeat 18 0x12
Repeat_AB 30 0x1E
Slow- 10 0x0A
Slow+: 14 0x0E
Program 22 0x16
Clear 28 0x1C
Display 0 0x00
Zoom 4 0x04
Setup 16 0x10
Return 24 0x18
Play 8 0x08
Stop 20 0x14
Up 5 0x05
Down 13 0x0D
Left 1 0x01
Right 25 0x19
Rew 69 0x45
Ff 9 0x09
Prev 21 0x15
Next 29 0x1D
Power_Off (unique): 11 0x0B (Note! only for V25 with newer software)
Power_On (unique): 23 0x17 (Note! only for V25 with newer software)
Dimmer 89 0x59
Select 17 0x11
10
DVD30 Remote Control Keys
Remote Control commands.
RC5 address = 12 (0x0c)
bits:
0x0300 = 0000 0011 0000 0000 (=768)
xxxx tsss ssdd dddd
(s ssss = 0 1100 = 0x0c = 12)
x=not used
t=toggle bit
s=system bits (address)
d=command (VALUE below)
short press (default) = 1 command.
long press = 3 consecutive identical commands
Key Dec. Value Hex. Value Action
STOP 0
FF 1
REW 2
SKIP+ 3
SKIP- 4
PLAY 5
PAUSE 6
OPEN/CLOSE 7
POWER ON/OFF 8
JOG FWD 0 9
JOG FWD 1 10
JOG FWD 2 11
JOG FWD 3 12
JOG REV 0 13
JOG REV 1 14
JOG REV 2 15
JOG REV 3 16
VNR (picture adjust) 17
POWER ON 18
POWER OFF 19
SUBTITLE 23
CURSOR LEFT 24
CURSOR RIGHT 25
CURSOR UP 26
CURSOR DOWN 27
FUNCTION MEMORY 28
CONDITION MEMORY 29
LAST MEMORY 30
MULTISPEED FWD 1 31
MULTISPEED FWD 2 32
0x00
0x01
0x02
0x03
0x04
0x05
0x06
0x07
0x08
0x09
0x0A
0x0B
0x0C
0x0D
0x0E
0x0F
0x10
0x11
0x12
0x13
0x17
0x18
0x19
0x1A
0x1B
0x1C
0x1D
0x1E
0x1F
0x20
11
MULTISPEED REV 1 33
MULTISPEED REV 2 34
STEP/SLOW FWD 35
STEP/SLOW REV 36
0 37
1 38
2 39
3 40
4 41
5 42
6 43
7 44
8 45
9 46
+10 47
SETUP 48
MENU 49
TOPMENU 50
DISPLAY (osd) 51
SEARCHMODE 52
ANGLE 53
AUDIO 54
REPEAT 55
REPEAT A-B 56
RANDOM 57
CLEAR 58
PROGRAM 59
ENTER 60
RETURN 61
DIMMER 62
PLAY/PAUSE 63
0x21
0x22
0x23
0x24
0x25
0x26
0x27
0x28
0x29
0x2A
0x2B
0x2C
0x2D
0x2E
0x2F
0x30
0x31
0x32
0x33
0x34
0x35
0x36
0x37
0x38
0x39
0x3A
0x3B
0x3C
0x3D
0x3E
0x3F
12
P30 Remote Control commands.
RC5 address = 20 (0x14)
bits:
0x0500 = 0000 0101 0000 0000 (=1280)
xxxx tsss ssdd dddd
(s ssss = 1 0100 = 0x14 = 20)
x=not used
t=toggle bit
s=system bits (address)
d=command (VALUE below)
Key Dec. Value Hex. Value Action
standby 39 (0x27) Standby ON
step up 30 (0x1e) In menus: menucommand "next"
Other: Next input
step down 31 (0x1f) In menus: menucommand "previous"
Other: Previous input
input mode 26 (0x1a) In menus: short press = previous menu
long press = leave menus
short press = toggle input mode (balance, center, rear, sub,
master)
Other long press = enter menus
mute 12 (0x0c) Toggle mute on/off
plus 16 (0x10) In menus: previous row
Other: Increase/change master volume, balance, center, rear,
sub
minus 17 (0x11) In menus: next row
Other: Decrease/change master volume, balance, center,
rear, sub
dim 10 (0x0a) Toggle display on/off
menu 38 (0x26) Enter/leave menus
For complete command, just add system address value 1280 with key value 39 (for standby) = 1319
(0x0527).
13
DVD26 Remote Control Keys
Remote Control commands.
RC5 address = 12 (0x0c)
bits:
0x0300 = 0000 0011 0000 0000 (=768)
xxxx tsss ssdd dddd
(s ssss = 0 1100 = 0x0c = 12)
x=not used
t=toggle bit
s=system bits (address)
d=command (VALUE below)
short press (default) = 1 command.
long press = 3 consecutive identical commands
Key Dec. Value Hex. Value Action
STOP 0
FF 1
REW 2
SKIP+ 3
SKIP- 4
PLAY 5
PAUSE 6
OPEN/CLOSE 7
POWER ON/OFF TOGGLE 8
POWER ON 18
POWER OFF 19
SUBTITLE 23
CURSOR LEFT 24
CURSOR RIGHT 25
CURSOR UP 26
CURSOR DOWN 27
RESUME ON/OFF 29
SLOW FWD 1 31
FRAME FWD 2 32
SLOW REW 1 33
FRAME REW 2 34
0 37
1 38
2 39
3 40
4 41
5 42
6 43
7 44
8 45
0x1D
0x1F
0x2A
0x2B
0x2C
0x2D
0x00
0x01
0x02
0x03
0x04
0x05
0x06
0x07
0x08
0x12
0x13
0x17
0x18
0x19
0x1A
0x1B
0x20
0x21
0x22
0x25
0x26
0x27
0x28
0x29
14
9 46
+10 47
SETUP 48
TITLE MENU 49
TOPMENU 50
DISPLAY (osd) 51
SEARCHMODE (goto) 52
ANGLE 53
AUDIO 54
REPEAT 55
REPEAT A-B 56
RANDOM 57
CLEAR 58
PROGRAM 59
ENTER 60
RETURN 61
DIMMER 62
PLAY/PAUSE TOGGLE 63
0x2E
0x2F
0x30
0x31
0x32
0x33
0x34
0x35
0x36
0x37
0x38
0x39
0x3A
0x3B
0x3C
0x3D
0x3E
0x3F
15
CD21 / CD31 Remote Control Commands.
RC5 address = 20 (0x14)
bits:
0x0500 = 0000 0101 0000 0000 (=1280)
xxxx tsss ssdd dddd
(s ssss = 1 0100 = 0x14 = 20)
x=not used
t=toggle bit
s=system bits (address)
d=command (VALUE below)
short press (default) = 1 command.
long press = 3 consecutive identical commands
Key Dec. Value Hex. Value Action
Open 45 (0x2d)
Play/Pause (Toggle) 53 (0x35)
stop 54 (0x26)
standby (Toggle) 12 (0x0c)
standby (Unique) 57 (0x39)
operate (Unique) 58 (0x3a)
dim 10 (0x0a)
next_track 32 (0x20)
ff 52 (0x34)
prev_track 33 (0x21)
rew 50 (0x32)
plus10 47 (0x2f)
time 11 (0x0b)
a_b 59 (0x3b)
repeat 29 (0x1d)
Mem 41 (0x29)
1 13 (0x0d)
2 14 (0x0e)
3 15 (0x0f)
4 18 (0x12)
5 19 (0x13)
6 20 (0x14)
7 21 (0x15)
8 22 (0x16)
9 23 (0x17)
0 24 (0x18)
shuffle 28 (0x1c)
intro 34 (0x22)
play2 (only Play) 36 (0x24)
pause (only Pause) 37 (0x25)
For complete command, just add system address value 1792 with key value 50 (for standby) = 1842
(0x0732).
16
Delay Box Remote Control commands.
RC5 address = 8 (0x08)
bits:
0x0200 = 0000 0010 0000 0000 (=256)
xxxx tsss ssdd dddd
(s ssss = 1 000 = 0x08 = 8)
x=not used
t=toggle bit
s=system bits (address)
d=command (VALUE below)
short press (default) = 1 command.
long press = 3 consecutive identical commands
Key Dec. Value Hex. Value Action
Standby 1 (0x01) Standby ON
Operate 2 (0x02) Standby Off
Standby 12 (0x0c) Toggle Standby/Operate
Up 3 (0x03) Increasing delay time
Down 4 (0x04) Decreasing delay time
Input 1 5 (0x05) Used for main input selection.
Input 2 6 (0x06) Used for mail input selection
Preset 1 7 (0x07) Delaytime memory 1
Preset 2 8 (0x08) Delaytime memory 2
Bypass 9 (0x09) Enable bypass mode.
Dim 10 (0x0A) Toggle DIM Mode
For complete command, just add system address value 0512 with key value 1 (for operate) = 0513 (0x0201).
17
T23 Remote Control Commands.
RC5 address = 16 (0x10)
bits:
0x0800 = 0000 1000 0000 0000 (=2048)
xxxx tsss ssdd dddd
(s ssss = 1 0000 = 0x10 = 16)
x=not used
t=toggle bit
s=system bits (address)
d=command (VALUE below)
short press (default) = 1 command.
long press = 3 consecutive identical commands
Due to compability reasons command , 4, 5, 6 should not be used.
Key Dec. Value Hex. Value Action
Operate / Standby 1 (0x01) (Toggle)
Display 2 (0x02) (Shifts between RDS info)
Mono / Auto 3 (0x07) toggle (in DAB-mode, enter menu)
FM Manual Tune UP
DAB service +,
menu +
FM Manual Tune Down
DAB service -,
menu Preset 1 (direct) 10 (0x0a)
Preset 2 (direct) 11 (0x0b)
Preset 3 (direct) 12 (0x0c)
Preset 4 (direct) 13 (0x0d)
Preset 5 (direct) 14 (0x0e)
Preset 6 (direct) 15 (0x0f)
Preset 7 (direct) 16 (0x10)
Preset 8 (direct) 17 (0x11)
Preset 9 (direct) 18 (0x12)
Preset 0 24 (0x18)
Store (mem) 19 (0x13)
Preset +10 23 (0x17)
Clear 29 (0x1D)
Preset UP (DAB/FM) 20 (0x14)
Preset Down (DAB/FM) 21 (0x15)
Dim toggle 22 (0x16) (toggle between DIM-modes)
Standby Mode Off (unique) 25 (0x19)
Standby mode On (unique) 26 (0x1A)
FM Search up 27 (0x1B)
FM Search down 28 (0x1C)
Select 30 (0x1E)
Auto, default 31 (0x1F) (in FM, enable auto-shift
Mono 32 (0x20) (in FM, enable mono mode), (unique)
8 (0x08) (long press search up)
9 (0x09) (long press search down)
stereo/mono), (unique)
18
Toggle DAB / FM mode 33 (0x21)
DAB mode (unique) 34 (0x22)
FM mode (unique) 35 (0x23)
For complete command, just add system address value 1024 with key value 1 (for operate) = 1025 (0x0401).
19
Cdi10 Remote Control Keys
RC5 address = 14 (0x0e)
bits:
0x0380 = 0000 0011 1000 0000 (=896)
xxxx tsss ssdd dddd
(s ssss = 0 1110 = 0x0e = 14)
x=not used
t=toggle bit
s=system bits (address)
d=command (VALUE below)
short press (default) = 1 command.
long press = 3 consecutive identical commands
Key Dec. Value Hex Value Action
Standby 8 0x08 Standby toggle
1 38 0x26
2 39 0x27
3 40 0x28
4 41 0x29
5 42 0x2A
6 43 0x2B
7 44 0x2C
8 45 0x2D
9 46 0x2E
Clear 58 0x3A
0 37 0x25
+10 47 0x2F
Volume - 29 0x1D
Arrow up 26 0x1A
Volume + 30 0x1E
Arrow Left 24 0x18 In FM Tune Down
Select 60 0x3C
Arrow Right 25 0x19 In FM Tune UP
stop 0 0x00
Arrow Down 27 0x1B
Play/Pause toggle 63 0x3F
DIM 62 0x3E
Mode 54 0x36 In FM toggle mono/Auto. In DAB mode toggle tuning alternatives.
Display 51 0x33 In FM toggle FM/RDS information. In DAB mode toggle DAB
information / Text.
Open 7 0x07
Skip back 4 0x04 In CD skip back, In FM Search Down
Mem 23 0x17
Skip Forward 3 0x03 In CD Skip Forward, In FM Search UP
REW 2 0x02
Repeat 55 0x37
FF 1 0x01
IN1 17 0x11 Direct input selection
IN2 20 0x14 Direct input selection
20
IN3 21 0x15 Direct input selection
IN4 (front) 22 0x16 Direct input selection
CD 12 0x0C Direct input selection
DAB/FM (toggle) 13 0x0D
Operate (uniqe) 18 0x12 Standby mode off
OFF (unique) 19 0x13 OFF mode on
Standby (unique) 16 0x10 Standby mode ON
Pause 6 0x06 only pause
Play 5 0x05 only play
Repeat a-b 56 0x38
Resume on/off 35 0x23
Dab 14 0x0E Direct input selection
FM 15 0x0F Direct input selection
21
DVDi10 Remote Control Commands.
RC5 address = 18 (0x12)
bits:
0x0480 = 0000 0100 1000 0000 (=1152)
xxxx tsss ssdd dddd
(s ssss = 1 0010 = 0x12 =18)
x=not used
t=toggle bit
s=system bits (address)
d=command (VALUE below)
short press (default) = 1 command.
long press = 3 consecutive identical commands
Function Dec. Value Hex Value Action
Standby(toggle) 8
1 38
2 39
3 40
4 41
5 42
6 43
7 44
8 45
9 46
Clear 58
0 37
+10 47
Volume - 29
Arrow up 26
Volume + 30
Arrow Left 24
Select 60
Arrow Right 25
Stop/Open 0
Arrow Down 27
Play/Pause (toggle) 63
Menu 49
DIM 62
Mode 54
Display 51
Setup 48
Skip - 4
MEM 59
Skip + 3
REW 2
Repeat 55
FF 1
Goto 52
0x08
0x26
0x27
0x28
0x29
0x2A
0x2B
0x2C
0x2D
0x2E
0x3A
0x25
0x2F
0x1D
0x1A
0x1E
0x18
0x3C
0x19
0x00
0x1B
0x3F
0x31
0x3E
0x36
0x33
0x30
0x04
0x3B
0x03
0x02
0x37
0x01
0x34
22
Angle 53
Topmenu 50
Subtitle 23
DVD 12
FM 15
DAB/AM 13
ipod 16
IN1 17
IN2 20
IN3 21
IN4 22
Operate (uniqe) 18
Standby (unique) 19
Open 7
Pause 6
Play 5
Repeat a-b 56
Resume on/off 35
Slow FWD1 31
Frame FMD2 32
Slow REW1 33
Frame REW2 34
Return 61
Dab 14
Am 11
Random 57
0x35
0x32
0x17
0x0C
0x0F
0x0D
0x10
0x11
0x14
0x15
0x16
0x12
0x13
0x07
0x06
0x05
0x38
0x23
0x1F
0x20
0x21
0x22
0x3D
0x0E
0x0B
0x39
23
SP32/SPA22 Remote Control Commands
RC5 address = 28 (0x1c)
bits:
0x0700 = 0000 0111 0000 0000 (=1792)
xxxx tsss ssdd dddd
(s ssss = 1 1100 = 0x1c = 28)
x=not used
t=toggle bit
s=system bits (address)
d=command (VALUE below)
short press (default) = 1 command.
long press = 3 consecutive identical commands
IR Dec. Value Hex. Value Describtion
Standby toggle 50 0x32 Toggle standby
Standby ON 59 0x3B Standby ON
Operate 58 0x3A Standby OFF
Step-UP 16 0x10 Next main input / prev row in menus
Step Down 17 0x11 Previous main input / next row in menus
Input mode
(balanced)
Mute 49 0x31 Mute On / Off
Plus 30 0x1E Volume +
Minus 31 0x1F Volume Dim 10 0x0A DIM On / Off
Menu 38 0x26 Menu / Menu-back / Menu exit
Mode 42 0x2A Next surround mode for 2ch inputs
Select 43 0x2B Menu command + (select)
0 24 0x18 Direct input access
1 13 0x0D Direct input access
2 14 0x0E Direct input access
3 15 0x0F Direct input access
4 18 0x12 Direct input access
5 19 0x13 Direct input access
6 20 0x14 Direct input access
7 21 0x15 Direct input access
8 22 0x16 Direct input access
9 23 0x17 Direct input access
+10 47 0x2F Direct input access
Zone II Volume + 32 0x20 Increase Zone II volume
Zone II Volume - 33 0x21 Decrease Zone II volume
Zone II Mute 34 0x22 Mute Zone2 output
Zone II input + 48 0x30 Next Zone II input
Zone II input - 36 0x24 Prevoius Zone II input
Zone II input 1 2 0x02 Zone II input direct
Zone II input 2 3 0x03 Zone II input direct
26 0x1A Balance / Center / Surr / Surr back / Sub / Master -volume toggle
24
Zone II input 3 4 0x04 Zone II input direct
Zone II input 4 5 0x05 Zone II input direct
Zone II input 5 6 0x06 Zone II input direct
Zone II input 6 7 0x07 Zone II input direct
Zone II input 7 8 0x08 Zone II input direct
Zone II input 8 9 0x09 Zone II input direct
Zone II input 9 12 0x0C Zone II input direct
Zone II input 0 1 0x01 Zone II input direct
Zone II input +10 11 0x0B Zone II input direct
25
CD32 Remote Control Commands.
RC5 address = 20 (0x14)
bits:
0x0500 = 0000 0101 0000 0000 (=1280)
xxxx tsss ssdd dddd
(s ssss = 1 0100 = 0x14 = 20)
x=not used
t=toggle bit
s=system bits (address)
d=command (VALUE below)
short press (default) = 1 command.
long press = 3 consecutive identical commands
Dec.
IR
Dimmer 10
Time 11
Power ON/OFF
1 13
2 14
3 15
4 18
5 19
6 20
7
8 22
9 23
0 24
Shuffle (toggle) 28
Repeat 29
Next Track 32 0x20
Previous Track 33 0x21
Sample rate toggle 36
Play (unique) 5
Pause (unique) 37
Open / Close toggle
+10
Rew 50
FF 52
Play / Pause Toggle 53
Stop 54
Operate Off 57 0x39 Only standby mode ON
Operate ON 58 0x3A Only standby mode Off
Mem 41 0x29 Programming mode
Arrow up 40 0x28 Navigation in USB
Arrow left 44 0x2C Navigation in USB
Select 46 0x2E Navigation in USB
Arrow right 51 0x33 Navigation in USB
Arrow down 56 0x38 Navigation in USB
Mode/Audio 55 0x37 Toggle between USB/CD
Value
12 0x0C Toggle standby
21
45
47
Hex Value Describtion
0x0A
0x0B
0x0D
0x0E
0x0F
0x12
0x13
0x14
0x15
0x16
0x17
0x18
0x1C
0x1D
0x24
0x05
0x25
0x2D
0x2F
0x32
0x34
0x35
0x36
DIM Toggle
Enable in play-mode
Enable in play-mode
toggle 44.1, 48, 96 Khz.
Only play
Only pause
Enter folder / play in USB
26
I32 Remote Control Commands.
RC5 address = 20 (0x14)
bits:
0x0500 = 0000 0101 0000 0000 (=1280)
xxxx tsss ssdd dddd
(s ssss = 1 0100 = 0x14 = 20)
x=not used
t=toggle bit
s=system bits (address)
d=command (VALUE below)
short press (default) = 1 command.
long press = 3 consecutive identical commands
Dec.
IR
Toggle standby 12
Standby (unique) 1
Operate (unique)
Step up 30
Step down 31
Select 43
Arrow right 8
Menu 0
Arrow left 9
Balance 26
Mute
Plus 16
Minus 17
Dim 10
Menu (Top Level) 65
Direct input 1 60 0x3C
Direct input 2 61
Direct input 3 62
Direct input 4 63
Direct input 5 3
Value Hex Value Describtion
0x0C
0x01
2 0x02 Only Operate
0x1E
0x1F
0x2B
0x08
0x00
0x09
0x1A
49
0x31
0x10
0x11
0x0A
0x41
0x3D
0x3E
0x3F
0x03
Standby on/off toggle
Only standby
input / menu up
input / menu down
Menu navigation
Menu navigation
Menu navigation
Menu navigation
Mute toggle
Volume up
Volume down
Toggle dim levels
Menu navigation
27
History
V16
Added:
DVD-30, Sp31 (new model)
V25 codes corrected.
Date / revision number added to first page.
V17
Updated DVD-30 codes
V18
Added: I30, I21 DVD-26, CD21, CD31, Delaybox
Minor error corrections (Text & layout).
Primare Logo changed
V19
Changed to SP31 / SPA21, Removed “new model”.
Bugs in SPA21 / SPA20 list corrected “record path”
Bugs in DVD-26 corrected “Random, “serchmode”
V20
Added T22 and T23, added SPA21 on the first page.
Added Cdi10.
V2.1
Changed version system to X.X, because of confusion with Primare V20 DVD-player
Added DVDi10 and SP32/SPA22
Fixed various errors in system address describtions
V2.2
Added all Hex. Values.
V2.3
Added CD32, I32.
28
Loading...