201 22" Planer
Designed with production in mind, a new machine
with increased capacity and loaded with features
to make short work of your work!
The Gold Standard Since 1921.
201 22" Planer
The Gold Standard Since 1921.
This 1,300 lb. heavy-duty cast iron
planer offers rock solid rigidity and
accurate planing for years to come.
The hinged top allows easy access
to the rollers and knives. The hood
comes standard with a 5" dust port
for easy attachment to any dust
collection system. The cutterhead
is complete with four high speed
steel knives and turns at 4,800 rpm
producing 19,200 cuts per minute.
The anti-kick back fingers and
pressure bar are located in close
proximity to the cutterhead for
an exceptional finish.
■ The well
designed infeed and outfeed rollers
are fitted with roller bearings for long
roller life. The sectional infeed and
chip breaker are specially designed
to allow multiple boards to be planed
at the same time. The adjustable bed
roller facilitates both rough and finish
planing. The solid steel outfeed roller
is machined with small serrations to
insure a smooth finish yet provide
positive feeding.
■ The two-speed
gearbox with machined detents
is quickly changed up front when
switching from rough to finish work.
You may easily raise the massive
ribbed cast iron, ground finished
table
1
/16" with each turn of the hand
wheel.
■ The model 201 is available
with 7
1
/2 horsepower, 3-phase 230 or
460 volt or 7
1
/2 horsepower, single-
phase motors. This planer is perfect
for the small to medium shop with
continuous planing requirements.
FEATURE
All cast iron construction
1,300 lb.
2 feed speeds — 20/30 fpm
Segmented infeed roller with
sectional chip breaker
4-knife head — 22" wide
Roller bearing feed rollers
Adjustable bed rollers
Heavy cast iron table travels
on 2 large lead screws
BENEFIT
Solid, rigid, accurate with no vibration
Accommodates rough and fine
finish work
Allows multiple piece planing and
consistent feed and finish
Fine finish cuts at 19,200 per minute
and widest capacity in its class
Insure long trouble-free use of machine
Allow smooth feeding of rough and
finished workpieces
Offers full support for large workpieces.
1 handle turn =
1
/16"
Large diameter 4-knife
cutterhead, sectional infeed
roller and chip breaker with
roller bearing support on
both infeed and outfeed
rollers.
Heavy-duty, oil bath
2-speed gearbox transmits
full power to feed rollers.
Oversized table with fully
adjustable easy set bed
rollers. Large inch/metric
scale for easy viewing.
WMH TOOL GROUP
Full 22" x 9
1
/2" capacity
Rugged cast iron
construction throughout
the machine
Segmented infeed roller
and chip breaker
All controls are easily
accessible from front
of machine
Big 7
1
/2HP motor in single
or three PH
201 22" Planer
The Gold Standard Since 1921.
Model Number 201
Motor HP/Voltage/Phase 7
1
/2HP 1 & 3 PH
Working Width 560mm/22
"
Maximum Depth Cut
3
/16
"
Minimum Thickness
1
/8
"
Maximum Thickness 9
1
/4
"
Segmented Infeed Roller Diameter 3
"
Steel Outfeed Roller Diameter 3
"
Feed Speeds 20/30 fpm
Bed Rollers Adjustable from Front 2
Table Size L x W 32
1
/4
"
x24
"
Minimum Length Workpiece 10
"
Table Height Adjust Manual 1 Turn =
1
/16
"
Readout Scale in/mm
Cutterhead Diameter 3
1
/4
"
Number of Knives 4
Cutterhead Speed 4800
Table Support 2-column
Dust Connect Diameter 125mm/5
"
Minimum CFM Required 900
Weight Gross/Net Lbs. 1430/1350 lbs
Tools Supplied Yes
Overall Dimensions Assembled 39"Lx 49"Wx 53"H
PN Single-Phase 230V 1791261
PN Three-Phase 230V 1791262
PN Three-Phase 460V 1791280
PN Accy. Knives (4) Set 6012179
PN Accy. Bed & Feed Roller Setting Gauge 2230002
WMH TOOL GROUP • 123 Alpha Drive • City, State, Zip • Toll-free 1-800-xxx-xxxx Part No. 91-601
Loading...