THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
ORDER NO.
RRV2203
Type
HY‡
HV‡
: Alter the wiring of the Power -supply block at the primary winding of Power -transformer referring to the "Line V oltage Selection" described
∗
in Service Manual.
Model
VSA-E07
Power Requirement
AC220-230V
AC230V
The voltage can be converted by
the following method.
AC240V,
AC240V,
∗
∗
¶ This service manual should be used together with the following manual(s):
Model No.Order No.Remarks
VSX-908RDS-G/HYRRV2166
CONTENTS
1. CONTRAST OF MISCELLANEOUS PARTS
2. PCB CONNECTION DIAGRAM
3. SCHEMATIC DIAGRAM
4. REMOTE CONTROL UNIT
PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS SERVICE, INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER ELECTRONIC (EUROPE) N.V. Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 1999
.....................................
............................
.................................
........
2
9
10
20
T – ZZK SEPT. 1999 Printed in Japan
VSA-E07
1. CONTRAST OF MISCELLANEOUS PARTS
NOTES:
CONTRAST TABLE
VSA-E07/HY, HV and VSX-908RDS-G/HY are constructed the same except for the following :
Ref. No. MarkSymbol and DescriptionVSX-908RDS-GVSA-E07VSA-E07Remarks
P5-12 VIDEO ASSYAWX7422AWX7419AWX7419
P5-13 S-VIDEO ASSYAWX7395AWX7308AWX7308
P5-16 DIGITAL-I/O ASSYAWX7396AWX7315AWX7315
Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List.
The mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
Screws adjacent to mark on product are used for disassembly.
Reference Nos. indicate the pages and Nos. in the service manual for the base model.
When ordering resistors, first convert resistance values into code form as shown in the following examples.
Ex.1 When there are 2 effective digits (any digit apart from 0), such as 560 ohm and 47k ohm (tolerance is shown by J=5%,
and K=10%).
560
47k
0.5
1
56 x 10
47 x 103
R50
1R0
1
561
473
RD1/4PU J
RD1/4PU J
RN2H K
RS1P K
561
473
R50
1R0
Ex.2 When there are 3 effective digits (such as in high precision metal film resistors).
P3- 4Remote Control Unit (CU-VSX165)AXD7236Not usedNot used
P3- 4Remote Control Unit (CU-VSA032)Not usedAXD7217 *1AXD7217 *1
P3- 9Packing CaseAHD7815AHD7813AHD7813
P3-14Operating Instructions (German)ARC7244ARC7271Not used
P3-15Operating Instructions (French)ARC7245ARC7247Not used
P3-16Operating Instructions (Italian)ARC7246ARC7248Not used
P3-17Operating Instructions (Dutch)ARC7270ARC7249Not used
P3-18Operating Instructions (Swedish)ARC7280ARC7283Not used
P3-19Operating Instructions (Spanish)ARC7281ARC7284Not used
P3-20Operating Instructions (Portuguese)ARC7282ARC7285Not used
Ref. No. MarkSymbol and DescriptionVSX-908RDS-GVSA-E07VSA-E07Remarks
/HY/HY/HV
P5-20AC Power CordADG7029ADG7029VDG1063
P5-22FM/AM TUNER UnitAXX7048Not usedNot used
P5-26AC Cord SpacerANG1153ANG1153Not used
P5-26Cord StopperNot usedNot usedCM-22B
P5-27Bonnet CaseAZN7809Not usedNot used
P5-31Lead Card 13P AD (J16)ADD7169Not usedNot used
P5-37Assy HolderANG7121ANG7139ANG7139
P5-39Card SpacerAEC7133Not usedNot used
P5-43NSPFrameANG7238ANG7243ANG7243
P5-48NSPPanel StayAND7031AND7032AND7032
P5-72ScrewBBT30P100FCCIBZ30P100FCCIBZ30P100FCC
P5-73ScrewFBT40P080FNINot usedNot used
P5-78AC Socket 3PAKP-502AKP-502Not used
P5-79Caution LabelARW7036ARW7036Not used
P5-80Fuse HolderNot usedNot usedVKR1003
EXTERIOR SECTION
P5-81Fuse (T5A)Not usedNot usedPEK1003
P5-83NSPSpacerAEB1254Not usedNot used
PIONEER CORPORATION 4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS SERVICE, INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER ELECTRONIC (EUROPE) N.V. Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
c
PIONEER CORPORATION 1999
T – ZZK JULY 1999 Printed in Japan
VSX-908RDS, VSX-908RDS-G
1. SAFETY INFORMATION
This service manual is intended for qualified service technicians ; it is not meant for the casual do-ityourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained
to properly and safely repair complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may
void the warranty. If you are not qualified to perform the repair of this product properly and safely, you
should not risk trying to do so and refer the repair to a qualified service technician.
WARNING
This product contains lead in solder and certain electrical parts contain chemicals which are known to the state of California to cause
cancer, birth defects or other reproductive harm.
NOTICE
(FOR CANADIAN MODEL ONLY)
Fuse symbols (fast operating fuse) and/or (slow operating fuse) on PCB indicate that replacement parts must
be of identical designation.
REMARQUE
(POUR MODÈLE CANADIEN SEULEMENT)
Les symboles de fusible (fusible de type rapide) et/ou (fusible de type lent) sur CCI indiquent que les pièces
de remplacement doivent avoir la même désignation.
Health & Safety Code Section 25249.6 – Proposition 65
(FOR USA MODEL ONLY)
1. SAFETY PRECAUTIONS
The following check should be performed for the
continued protection of the customer and service
technician.
LEAKAGE CURRENT CHECK
Measure leakage current to a known earth ground (water
pipe, conduit, etc.) by connecting a leakage current tester
such as Simpson Model 229-2 or equivalent between the
earth ground and all exposed metal parts of the appliance
(input/output terminals, screwheads, metal overlays, control
shaft, etc.). Plug the AC line cord of the appliance directly
into a 120V AC 60Hz outlet and turn the AC power switch
on. Any current measured must not exceed 0.5mA.
Reading should
not be above
0.5mA
Earth
ground
Device
under
test
Also test with
plug reversed
(Using AC adapter
plug as required)
Test all
exposed metal
surfaces
Leakage
current
tester
ANY MEASUREMENTS NOT WITHIN THE LIMITS
OUTLINED ABOVE ARE INDICATIVE OF A POTENTIAL
SHOCK HAZARD AND MUST BE CORRECTED BEFORE
RETURNING THE APPLIANCE TO THE CUSTOMER.
2. PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in the appliance
have special safety related characteristics. These are
often not evident from visual inspection nor the protection
afforded by them necessarily can be obtained by using
replacement components rated for voltage, wattage, etc.
Replacement parts which have these special safety
characteristics are identified in this Service Manual.
Electrical components having such features are identified
by marking with a
in this Service Manual.
The use of a substitute replacement component which does
not have the same safety characteristics as the PIONEER
recommended replacement one, shown in the parts list in
this Service Manual, may create shock, fire, or other hazards.
Product Safety is continuously under review and new
instructions are issued from time to time. For the latest
information, always consult the current PIONEER Service
Manual. A subscription to, or additional copies of, PIONEER
Service Manual may be obtained at a nominal charge from
PIONEER.
on the schematics and on the parts list
AC Leakage Test
2
VSX-908RDS, VSX-908RDS-G
2. EXPLODED VIEWS AND PARTS LIST
NOTES:• Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List.
The mark found on some component parts indicates the importance of the safety factor of the part.
•
Therefore, when replacing, be sure to use parts of identical designation.
Screws adjacent to mark on the product are used for disassembly.
•
2.1 PACKING
5
13
Refer to
"7.3 REMOTE
CONTROL UNIT".
(1) PACKING PARTS LIST
Mark No. Description Part No.
4
8
9
11
1
2
3 (Except HY/GR Type)
12
10
7 (2/2)
14 (Except HV Type)
15, 16, 17, 18, 19, 20
(HY/EW and HY Types Only)
13
7 (1/2)
Mark No. Description Part No.
1 AM Loop AntennaATB7009
2 FM Wire AntennaADH7010
3 Operating Instructions(English) See Contrast table (2)
4 Remote Control UnitSee Contrast table (2)
VSX-908RDS/HY/EW, HY/GR, HV and VSX-908RDS-G/HY are constructed the same except for the following :
Part No.
Mark No.Symbol and DescriptionVSX-908RDSVSX-908RDSVSX-908RDSVSX-908RDS Remarks
/HY/EW/HY/GR/HV-G/HY
3Operating Instructions (English)ARB7187Not usedARB7187ARB7187
4Remote Control Unit (CU-VSX162)AXD7214AXD7214AXD7214Not used
4Remote Control Unit (CU-VSX165)Not usedNot usedNot usedAXD7236
9Packing CaseAHD7814AHD7814AHD7814AHD7815
63 Terminal ScrewAKE-031
NSP64 Under Base 26ANA7089
NSP65 Binder (BK-1)ZCA-BK1
66 ScrewBBT30P080FCC
67 ScrewBBZ30P080FZK
68 ScrewABA1193
69 ScrewIBZ30P080FCC
70 ScrewBBZ30P180FMC
31 Lead Card 13P AD (J16)ADD7169
32 Lead Card 14P (J17)ADD7165
33 Lead Card 21P (J18)ADD7164
34 Lead Card 23P BD SLD (J12) ADD7160
35 Lead Card 26P (J15)ADD7163