Pioneer PDPS-33-LR Service manual

PDP-S33-LR

SPEAKER SYSTEM

PDP-S33-LR

ORDER NO.

RRV3142

XIN/UC

65S

This service manual is intended for qualified service technicians; it is not meant for the

casual do-it-yourselfer. Qualified technicians have the necessary test equipment and

tools, and have been trained to properly and safely repair complex products such as

those covered by this manual.

Improperly performed repairs can adversely affect the safety and reliability

of the product and may void the warranty. If you are not qualified to perform the repair

of this product properly and safely, you should not risk trying to do so and refer the

repair to a qualified service technician.

WARNING

This product contains lead in solder and certain electrical parts contain chemicals

which are known to the state of California to cause cancer, birth defects or other

reproductive harm.

Health & Safety Code Section 25249.6 – Proposition 65

PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan

PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A. PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936

PIONEER CORPORATION 2005

T-ZZK APR. 2005 Printed in Japan

FOR PRECAUTION OF REASSEMBLY AND DISASSEMBLY

The grille is attached to the baffle using double-sided self-adhesive tape. To avoid damaging the grille, work with the speaker on top of a blanket or similar, face up. There are two slots in the lower part of the speaker. Insert a screwdriver(-) into each slot and push down detach the lower part. Turn the speaker over and insert a screwdriver(-) between the grille and the baffle. Taking care not to damage the baffle, push down on the screwdriver(-) to prize the baffle and grille apart.

When reattaching the grille, use double-sided self-adhesive tape in the locations shown in the diagram and press the grille assy into place.

The grille is fixed using boss and double-sided self-adhesive tape(The tape is in the locations indicated in the diagram below). Do not use a dryer to heat the self-adhesive tape when removing the grille.

GRILLE

Slot

Screwdriver(-)

The woofer is attached to the baffle by external screws. To de-

Grille

tach it, unfasten those screws. When attaching it, face its termi-

nal downward.

Down

The tweeter is attached to the baffle by external screws. To detach it, unfasten those screws.

Baffle

LOCATIONS TO FIX DOUBLE-SIDED SELF-ADHESIVE TAPE

(11)

Tape (SEH1074 x2)

Tape (SEH1063)

Tape (SEH1074 x2)

(11)

1234

PDP-S33-LR

Tape (SEH1063)

234

PARTS LIST

OTES:

Mark No. Description Part No.

NSP Baffle L SNK2860 NSP Baffle R SNK2861 NSP Cabinet L SNK2864 NSP Cabinet R SNK2865

NSP Grille Cloth SAS1571 NSP Grille Frame SMH1105

NSP Packing SEB1232 NSP Gasket SEC1855 NSP Gasket SEC1856 NSP Gasket SEC1857 NSP Gasket SEC1860 NSP Terminal SFK1034 NSP Terminal SFK1035

NSP Rosin Core Solderpbf ZSA-5020-1R6 NSP Red-Black Wire ZWWAC3318-20 NSP Red-White Wire ZWWAC3318-29 NSP Blue-White Wire ZWWAC3318-69

NSP Model Label (L) SAN3661 NSP Model Label (R) SAN3662 NSP Insert Nut M5 SBN1056 NSP Gasket (BF: WF-TW, Top, Bottom) SEB1250

NSP Gasket (Input-Side) SEB1255 NSP Gasket (WF: Input) SEB1256 NSP Gasket (TW: Input) SEB1271 NSP Gasket (CAB: Input) SEB1273

NSP Gasket (WF: Gasket) SEC1754 NSP Gasket (CAB: Rib Long) SEC1858 NSP Gasket (CAB: Rib Short) SEC1859 NSP Gasket (BF: Side) SEC1863 NSP Gasket (CAB: Long Inside) SEC1931

NSP Gasket (CAB: Short Inside) SEC1932 NSP Gasket (BF: WF Side) SEC1934 NSP Felt (Duct: Inside) SED1112 NSP Felt (CAB: C Term) SED1113

NSP Paper Tube 26 SMR1380 NSP Port Tube Ring 26 SMR1382 NSP Acoustic Absorbent (Roll : Small) SMT1240 NSP Acoustic Absorbent (TW: Back) SMT1245

NSP Acoustic Absorbent (CAB: Roll) SMT1246 NSP Acoustic Absorbent (CAB: T B) SMT1248 NSP Acoustic Absorbent (CAB: B) SMT1249 NSP Label Serial (Model Label L,R) SRW1083

Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List. The mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation.

Grille ASSY SMG1847

Network ASSY SWN1736

Capacitor 2.7 SCE1029

Choke Coil 1.1 STH1260

Input Terminal KKX1015

Gasket (Input Terminal Back) SEC1724

Tape (Grille: Short) SEH1063

Tape (Grille: Long) SEH1074

For Packing

Mark No. Description Part No.

NSP Accessories Set (Flush & Screw,Cord) SME3629

NSP Accessories Set (Flush) SME3626

NSP Polyethylene Bag S1 KHL1079 NSP Label (R) SAK1014

NSP Bracket A SNA1447 NSP Clear Tape 12mm ZTA-400-12

NSP Polyethylene Bag S1 KHL1079 NSP Label (L) SAK1015

NSP Bracket A SNA1447 NSP Clear Tape 12mm ZTA-400-12

NSP Polyethylene Bag S1 KHL1079 NSP Label (R) SAK1014

NSP Bracket B SNA1448 NSP Clear Tape 12mm ZTA-400-12

NSP Polyethylene Bag S1 KHL1079 NSP Label (L) SAK1015

NSP Bracket B SNA1448 NSP Clear Tape 12mm ZTA-400-12

NSP Danpron Tape

NSP Accessory Set (Screw & Cord) SME3525 NSP Polyethylene Bag S1 KHL1079 NSP Screws Set SME3510

NSP Polyethylene Bag S0 KHL1081 NSP MAX No.10-1M ZMX-MAX10-1M

NSP MAX No.10-1M ZMX-MAX10-1M

NSP Danpron Tape NSP Clear Tape 12mm ZTA-400-12

Protector SHB1159

Spacer SHD1067 Accessory Case SHF1086 Bracket A ASSY (R) SNX1175

Gasket SEC1861 Gasket A SEC1935

Bracket A ASSY (L) SNX1176

Gasket SEC1861 Gasket A SEC1935

Bracket B ASSY (R) SNX1177

Gasket SEC1861 Gasket B SEC1936

Bracket B ASSY (L) SNX1178

Gasket SEC1861 Gasket B SEC1936

ZTA-DANPRON-50CL

Screw BMZ50P100FTB

Speaker Wire Set SME3526

Speaker Wire SDS1166

ZTA-DANPRON-50CL

Speaker A101EC65-54F Speaker FADD55-52F

PDP-S33-LR

+ 6 hidden pages