Pioneer GM-H200, GM-4200 User Manual

Download

Specifications and Main Features

Model: GM-H200/UC
General Specifications: 14.4 V. DC Supply with a variation of 10.8-15.6V limit
Earthing: D.C. Negative system
Drawn Current: 40A Continuous power does use 492 units
Fused: 30 ax 2
Measure: 264 W x 58 H x 335 D mm
Overall weight: 7 Mg 15.4 IIbs excluding wiring leads.
Power Output (Max): 2 x 200 W/ 1 x 600 W (EIAJ methods confirm)
Power Output: 2 X 100W 1 x 300W at 4 ohm (20-20000 Hz 0.05% THD) 2 x 150 W at 2 ohms 20 - 20 000 Hz 0.05% THD
Load Rating: 2-8 ohms higher is acceptable
Signal Range: 10-50 KHz (0db, -1)
Noise Ratio: 105 dB (IHF - A network)
Distort: 0.001 At 20 W, 1 kHz frequency where used
Noise Ratio and Separation: 70 db frequency 1k
Voltage rate input. : 0.2 - 2 V /8 k:
Model: GM-4200/EW
General Features: Power Supply: 14.4 DC with allowance of 10.8 to 15.6.
Current consumption: 40 A (on continuous power, 492)
Average current drawn: 13 A (two channels with 4Ω each), 18 A (for one 4Ω channel)
Fuses: Two thirty amp fuses
Dimensions: 264 (W) x 58 (H) x 335 (D) mm
Total weight: 7.0 kg (Leads for wiring not included)
Maximum Output with RCA: 240 W x 2 Channels/640 W for one x EIAJ
Maximum Single Output: 240 W x 2 Channels 320 for one at 4 Ohms : 20 to 20 k hertz range with THD of 0.056%. Maximum output is 160 W x 2 - (2 Ohm 20 to 20 k hertz with THD about of 0.05%) times the 500 mA
Load impedance ranges: 2 up to 8 ohms in the allowable range.
Pass Band Frequency Range/responsiveness: 5hz - 50khz +/-0dB to +- 1dB
IEC: A Network
105 DBA Signature to Noise Ratio
Distortion: 0.0009 percent if power output in approximation of 20 watts and voice range is 1khz
Separation -70db 1 Khz
Input levels: for RCA 0.4 to 4 at 8/0 k ohms and for DIN 70 - 500mV at 500 22 k ohms

A few of these work together while others are output supply units

A universal din 6 headsets wire of type RCA connecting the amplifier and a Cable Lifter HiFi.

Frequently Asked Questions

Is GM H200UC/C amplifier a dual ply capable? The GM H200UC/C amplifier is indeed a dual ply capable amplifier boasting a dual routing capability and dual channel for 640W maximum output.
What is the frequency response range of the GM-4200/EW amplifier?

Frequency Range: 5 - 50 000 Hz (+0 dB, -1 dB).

What type of grounding system is used in these amplifiers?

Negative type of grounding system has been used for both models.

What is the recommended load impedance for the amplifiers?

The load impedance that is suggested is from 2 to 8 ohms.

What will happen if I connect a speaker with impedance less than 2 ohms?

It could damage the amplifier.

What is the procedure for connecting the amplifier to power?

The special battery lead with a red color supplied should be connected with the positive terminal of the battery directly.

What other reasonable steps should be taken during installation?

Make sure wires are tied down and installed away from sharp edges to prevent shorting out. Always connect the ground lead to a solid metal part of the vehicle body.