Pioneer DVJ-1000 User Manual [en, de, es, fr, it]

DVD PLAYER LECTEUR DE DVD DVD-SPIELER LETTORE PER DVD DVD-SPELER REPRODUCTOR DVD

DVJ-1000

Operating Instructions Mode d’emploi Bedienungsanleitung Istruzioni per l’uso Gebruiksaanwijzing Manual de instrucciones

IMPORTANT

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:

TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

D3-4-2-1-1_En-A

IMPORTANT

Ce symbole de l’éclair, placé dans un triangle équilatéral, a pour but d’attirer l’attention de l’utilisateur sur la présence, à l’intérieur du coffret de l’appareil, de “tensions dangereuses” non isolées d’une grandeur suffisante pour représenter un risque d’électrocution pour les êtres humains.

WICHTIG

Das Blitzsymbol in einem Dreieck weist den Benutzer darauf hin, dass eine Berührungsgefahr mit nicht isolierten Teilen im Geräteinneren, die eine gefährliche Spannung führen, besteht. Die Spannung kann so hoch sein, dass sie die Gefahr eines elektrischen Schlages birgt.

IMPORTANTE

Il simbolo del lampo con terminale a forma di freccia situato all’interno di un triangolo equilatero serve ad avvisare l’utilizzatore della presenza di una “tensione pericolosa” non isolata nella struttura del prodotto che potrebbe essere di un’intensità tale da provocare scosse elettriche all’utilizzatore.

ATTENTION

DANGER D´ELECTROCUTION

NE PAS OUVRIR

ATTENTION:

POUR ÉVITER TOUT RISQUE D’ÉLECTROCUTION, NE PAS ENLEVER LE COUVERCLE (NI LE PANNEAU ARRIÈRE). AUCUNE PIÈCE RÉPARABLE PAR L’UTILISATEUR NE SE TROUVE À L’INTÉRIEUR. CONFIER TOUT ENTRETIEN À UN PERSONNEL QUALIFIÉ UNIQUEMENT.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

ACHTUNG:

UM SICH NICHT DER GEFAHR EINES ELEKTRISCHEN SCHLAGES AUSZUSETZEN, DÜRFEN SIE NICHT DEN DECKEL (ODER DIE RÜCKSEITE) ENTFERNEN. IM GERÄTEINNEREN BEFINDEN SICH KEINE VOM BENUTZER REPARIERBAREN TEILE. ÜBERLASSEN SIE REPARATUREN DEM QUALIFIZIERTEN KUNDENDIENST.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

ATTENZIONE:

PER EVITARE IL RISCHIO DI SCOSSE ELETTRICHE, NON RIMUOVERE IL COPERCHIO (O IL RETRO). NON CI SONO PARTI INTERNE LA CUI MANUTENZIONE POSSA ESSERE EFFETTUATA DALL’UTENTE. IN CASO DI NECESSITÀ, RIVOLGERSI ESCLUSIVAMENTE A PERSONALE DI SERVIZIO QUALIFICATO.

Ce point d’exclamation, placé dans un triangle équilatéral, a pour but d’attirer l’attention de l’utilisateur sur la présence, dans les documents qui accompagnent l’appareil, d’explications importantes du point de vue de l’exploitation ou de l’entretien.

Ein Ausrufezeichen in einem Dreieck weist den Benutzer auf wichtige Bedienungs- und Wartungsanweisungen in den Dokumenten hin, die dem Gerät beiliegen.

Il punto esclamativo in un triangolo equilatero serve ad avvisare l’utilizzatore della presenza di importanti istruzioni di funzionamento e manutenzione riportate nel libretto allegato al prodotto.

D3-4-2-1-1_Fr

D3-4-2-1-1_Ge

D3-4-2-1-1_It

BELANGRIJK

De lichtflash met pijlpuntsymbool in een gelijkzijdige driehoek is bedoeld om de aandacht van de gebruikers te trekken op een niet geïsoleerde “gevaarlijke spanning” in het toestel, welke voldoende kan zijn om bij aanraking een elektrische shock te veroorzaken.

IMPORTANTE

La luz intermitente con el símbolo de punta de flecha dentro un triángulo equilátero. Está convenido para avisar el usuario de la presencia de “voltaje peligrosa” no aislada dentro el producto que podría constituir un peligro de choque eléctrico para las personas.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WAARSCHUWING:

OM HET GEVAAR VOOR EEN ELEKTRISCHE SHOCK TE VOORKOMEN, DEKSEL (OF RUG) NIET VERWIJDEREN. AAN DE BINNENZIJDE BEVINDEN ZICH GEEN ELEMENTEN DIE DOOR DE GEBRUIKER KUNNEN BEDIEND WORDEN. ENKEL DOOR GEKWALIFICEERD PERSONEEL TE BEDIENEN.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

ATENCIÓN:

PARA PREVENIR EL PELIGRO DE CHOQUE ELÉCTRICO NO REMOVER LA TAPA NI LAS PARTES DENTRO NO UTILIZADAS, LLAMAR UNA PERSONA CUALIFICADA

Het uitroepteken in een gelijkzijdige driehoek is bedoeld om de aandacht van de gebruiker te trekken op de aanwezigheid van belangrijke bedienings- en onderhoudsinstructies in de handleiding bij dit toestel.

D3-4-2-1-1_Du

El punto exclamativo dentro un triángulo equilátero convenido para avisar el usuário de la presencia de importantes instrucciones sobre el funcionamiento y la manutención en la libreta que acompaña el aparato.

D3-4-2-1-1_Sp

WARNING

This equipment is not waterproof. To prevent a fire or shock hazard, do not place any container filed with liquid near this equipment (such as a vase or flower pot) or expose it to dripping, splashing, rain or moisture.

AVERTISSEMENT

Cet appareil n’est pas étanche. Pour éviter les risques d’incendie et de décharge électrique, ne placez près de lui un récipient rempli d’eau, tel qu’un vase ou un pot de fleurs, et ne l’exposez pas à des gouttes d’eau, des éclaboussures, de la pluie ou de l’humidité.

WARNUNG

Dieses Gerät ist nicht wasserdicht. Zur Vermeidung der Gefahr von Brand und Stromschlag keine Behälter mit Flüssigkeiten (z.B. Blumenvasen und

-töpfe) in die Nähe des Gerätes bringen und dieses vor Tropfwasser, Spritzwasser, Regen und Nässe schützen.

ATTENZIONE

Questo apparecchio non è impermeabile. Per prevenire pericoli di incendi o folgorazioni, non posizionare nelle vicinanze di questo apparecchio contenitori pieni di liquidi (quali vasi da fiori, o simili), e non esporre l’apparecchio a sgocciolii, schizzi, pioggia o umidità.

WAARSCHUWING

Dit apparaat is niet waterdicht. Om brand of een elektrische schok te voorkomen, mag u geen voorwerp dat vloeistof bevat in de buurt van het apparaat zetten (bijvoorbeeld een bloemenvaas) of het apparaat op andere wijze blootstellen aan waterdruppels, opspattend water, regen of vocht.

ADVERTENCIA

Este aparato no es impermeable. Para evitar el riesgo de incendio y de descargas eléctricas, no ponga ningún recipiente lleno de líquido (como pueda ser un vaso o un florero) cerca del aparato ni lo exponga a goteo, salpicaduras, lluvia o humedad.

WARNING

Before plugging in for the first time, read the following

section carefully.

The voltage of the available power supply differs according to country or region. Be sure that the power supply voltage of the area where this unit will be used meets the required voltage (e.g., 230V or 120V) written on the bottom panel.

AVERTISSEMENT

Avant de brancher l’appareil pour la première, lisez attentivement la section suivante.

La tension de l’alimentation électrique disponible varie selon le pays ou la région. Assurez-vous que la tension du secteur de la région où l’appareil sera utilisé correspond à la tension requise (par ex. 230 V ou 120 V), indiquée sur le panneau inférieur.

D3-4-2-1-4_A_Fr MOD

WARNUNG

Vor dem erstmaligen Anschluss des Gerätes an das Stromnetz bitte den folgenden Hinweis sorgfältig beachten.

Die Netzspannung ist je nach Land verschieden. Vor der Inbetriebnahme des Gerätes sicherstellen, dass die örtliche Netzspannung mit der auf dem Typenschild an der Unterseite des Gerätes angegebenen Nennspannung (z.B. 230 V oder 120 V) übereinstimmt.

ATTENZIONE

Prima di collegare per la prima volta l’apparecchio alla sorgente di alimentazione leggere attentamente la sezione che segue.

La tensione della sorgente di elettricità differisce da Paese a Paese e da regione a regione. Verificare che la tensione di rete della zona in cui si intende utilizzare l’apparecchio sia quella corretta, come indicato sul pannello inferiore dell’apparecchio stesso (ad es.: 230 V o 120 V).

WAARSCHUWING

Lees zorgvuldig de volgende informatie voordat u de stekker de eerste maal in het stopcontact steekt.

De bedrijfsspanning van het apparaat verschilt afhankelijk van het land waar het apparaat wordt verkocht. Zorg dat de netspanning in het land waar het apparaat wordt gebruikt overeenkomt met de bedrijfsspanning (bijv. 230 V of 120 V) aangegeven op de onderkant van het apparaat.

ADVERTENCIA

Antes de enchufar el aparato a la corriente, lea la sección siguiente con mucha atención.

La tensión de la red eléctrica es distinta según el país o región. Asegúrese de que la tensión de la alimentación de la localidad donde se proponga utilizar este aparato corresponda a la tensión necesaria (es decir, 230 V ó 120 V) indicada en el panel inferior.

D3-4-2-1-3_A_En

D3-4-2-1-3_A_Fr

D3-4-2-1-3_A_Ge

D3-4-2-1-3_A_It

D3-4-2-1-3_A_Du

D3-4-2-1-3_A_Sp

D3-4-2-1-4_A_En

D3-4-2-1-4_A_Ge mod

D3-4-2-1-4_A_It MOD

D3-4-2-1-4_A_Dukmb

D3-4-2-1-4_A_SpMOD

mod

Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel.

IMPORTANT: THE MOULDED PLUG (FOR USE IN THE UNITED KINGDOM)

This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 5 amp fuse is fitted in this plug. Should the fuse need to be replaced, please ensure that the replacement fuse has a rating of 5 amps and that it is approved by ASTA or BSI to BS1362.

Check for the ASTA mark or the BSI mark on the body of the fuse.

If the plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be obtained from your local dealer.

If the fitted moulded plug is unsuitable for your socket outlet, then the fuse shall be removed and the plug cut off and disposed of safely. There is a danger of severe electrical shock if the cut off plug is inserted into any 13 amp socket.

If a new plug is to be fitted, please observe the wiring code as shown below. If in any doubt, please consult a qualified electrician.

IMPORTANT: The wires in this mains lead are coloured in accordance with the following code: Blue : Neutral Brown : Live As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows ;

The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.

How to replace the fuse: Open the fuse compartment with a screwdriver and replace the fuse.

D3-4-2-1-2-2_B_En

CLASS 1 LASER PRODUCT

CAUTION

This product is a class 1 laser product, but this product contains a laser diode higher than Class 1. To ensure continued safety, do not remove any covers or attempt to gain access to the inside of the product. Refer all servicing to qualified personnel. The following caution label appears on your unit. Location: top of the DVD drive

ATTENTION

Cet appareil est un produit laser de Classe 1, mais la diode laser qu’il renferme est supérieure à la Classe 1. Pour garantir une sécurité constante, ne retirez aucun des couvercles et n’essayez pas d’avoir accès à l’intérieur de l’appareil. Confiez toute réparation à un personnel qualifié. L’étiquette suivante se trouve sur votre appareil. Emplacement : Sujr le dessus du lecteur DVD

ACHTUNG

Bei diesem Gerät handelt es sich zwar um ein Laserprodukt der Klasse 1, doch enthält es eine Laserdiode einer höheren Klasse als 1. Um einen stets sicheren Betrieb zu gewährleisten, weder irgendwelche Abdeckungen entfernen, noch versuchen, sich zum Geräteinneren Zugang zu verschaffen. Wartungsarbeiten sind grundsätzlich dem Kundendienstpersonal zu überlassen. Das Gehäuse ist mit dem unten abgebildeten Warnaufkleber versehen. Lage: Oberseite des DVD-Laufwerks

AVVERTENZA

Questo apparecchio è un prodotto al laser di Classe 1, ma contiene un diodo al laser di classe superiore alla Classe 1. Per ovvi motivi di sicurezza, non togliere alcuno dei coperchi dell’apparecchio e non tentare di accedere ai dispositivi interni allo stesso. Ogni e qualsiasi intervento o riparazione devono essere effettuate solamente da personale qualificato. Sull’apparecchio si trova applicata la seguente etichetta di avvertimento: Posizione: sopra l’unità DVD

LET OP

Dit apparaat is een klasse 1 laserproduct, maar het bevat een laserdiode van een hogere klasse dan 1. Om veiligheidsredenen mogen geen panelen worden verwijderd of de ombouw van het apparaat op andere wijze worden geopend. Laat alle reparaties over aan bevoegd onderhoudspersoneel. Op uw apparaat is het onderstaande waarschuwingslabel aangebracht. Locatie : Bovenkant van het DVD-station

PRECAUCIÓN

Este aparato es un producto de láser de clase 1, pero contiene un diodo de láser de clase superior a 1. Para mantener la seguridad en todo momento, no quite ninguna cubierta ni intente acceder al interior del aparato. Solicite todo el servicio técnico a personal cualificado. En su aparato encontrará la siguiente etiqueta de precaución. Ubicación: Encima de la unidad de DVD

D3-4-2-1-8_B

DRW2317-A

English

Français

Deutsch

Italiano

Nederlands

Español

WARNING

To prevent a fire hazard, do not place any naked flame sources (such as a lighted candle) on the equipment.

D3-4-2-1-7a_A_En

AVERTISSEMENT

Pour éviter les risques d’incendie, ne placez aucune flamme nue (telle qu’une bougie allumée) sur l’appareil.

D3-4-2-1-7a_A_Fr

WARNUNG

Keine Quellen offener Flammen (z.B. eine brennende Kerze) auf dieses Gerät stellen.

D3-4-2-1-7a_A_Ge

ATTENZIONE

Per evitare il pericolo di incendi, non posizionare sull’apparecchio dispositivi con fiamme vive (ad esempio una candela accesa, o simili).

D3-4-2-1-7a_A_It

WAARSCHUWING

Om brand te voorkomen, mag u geen open vuur (zoals een brandende kaars) op de apparatuur zetten.

D3-4-2-1-7a_A_Du

ADVERTENCIA

Para evitar el peligro de incendio, no ponga nada con fuego encendido (como pueda ser una vela) encima del aparato.

This product complies with the Low Voltage Directive (73/23/EEC, amended by 93/68/EEC), EMC Directives (89/336/EEC, amended by 92/31/EEC and 93/68/EEC).

Ce produit est conforme à la directive relative aux appareils basse tension (73/23/CEE), à la directive CE relative à la compatibilité electromagnétique (89/336/CEE, amendements 92/31/CEE et 93/68/CEE).

Dieses Produkt entspricht den Niederspannungsrichtlinien (73/23/EEC, geändert durch 93/68/EEC), den EMV-Richtlinien (89/336/EEC, geändert durch 92/31/EEC und 93/68/EEC).

Questo prodotto è conforme alla direttiva sul basso voltaggio (73/23/CEE emendata 93/68/CEE), direttive EMC 89/336/CEE, emendata 92/31/CEE e 93/68/CEE.

D3-4-2-1-7a_A_Sp

D3-4-2-1-9a_En

D3-4-2-1-9a_Fr

D3-4-2-1-9a

D3-4-2-1-9a_It

_Ge

VENTILATION CAUTION

When installing this unit, make sure to leave space around the unit for ventilation to improve heat radiation (at least 5 cm at rear, and 5 cm at each side).

WARNING

Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product, and to protect it from overheating. To prevent fire hazard, the openings should never be blocked or covered with items (such as newspapers, table-cloths, curtains) or by operating the equipment on thick carpet or a bed.

D3-4-2-1-7b_A_En

PRÉCAUTION DE VENTILATION

Lors de l’installation de l’appareil, veillez à laisser un espace suffisant autour de ses parois de manière

à améliorer la dissipation de chaleur (au moins 5 cm à l’arrière et 5 cm de chaque côté).

AVERTISSEMENT

Les fentes et ouvertures du coffret sont prévues pour la ventilation, pour assurer un fonctionnement stable de l’appareil et pour éviter sa surchauffe. Pour éviter les risques d’incendie, ne bouchez

amais les ouvertures et ne les recouvrez pas d’objets, tels que journaux, nappes ou rideaux, et n’utilisez pas l’appareil posé sur un tapis épais ou un lit.

D3-4-2-1-7b_A_Fr

VORSICHTSHINWEIS ZUR BELÜFTUNG

Bei der Aufstellung dieses Gerätes muss für einen ausreichenden Freiraum gesorgt werden, um eine einwandfreie Wärmeabfuhr zu gewährleisten (mindestens 5 cm hinter dem Gerät und jeweils 5 cm an der Seite des Gerätes).

WARNUNG

Im Gerätegehäuse sind Ventilationsschlitze und andere Öffnungen vorgesehen, die dazu dienen, eine Überhitzung des Gerätes zu verhindern und einen zuverlässigen Betrieb zu gewährleisten. Um Brandgefahr auszuschließen, dürfen diese Öffnungen auf keinen Fall blockiert oder mit Gegenständen (z.B. Zeitungen, Tischdecken und Gardinen) abgedeckt werden, und das Gerät darf beim Betrieb nicht auf einem dicken Teppich oder Bett aufgestellt sein.

D3-4-2-1-7b_A_Ge

Dit product voldoet aan de laagspanningsrichtlijn (73/23/EEG, gewijzigd bij 93/68/EEG), EMCrichtlijnen (89/336/EEG, gewijzigd bij 92/31/EEG en 93/68/EEG).

D3-4-2-1-9a_Du

Este producto cumple con la Directiva de Bajo Voltaje (73/23/ CE, correcto por la 93/68/CE), Directivas EMC (89/336/CE, correcto por la 92/31/CE y la 93/68/CE) .

D3-4-2-1-9a_Sp

iii

BELANGRIJKE INFORMATIE BETREFFENDE DE VENTILATIE

Let er bij het installeren van het apparaat op dat er voldoende vrije ruimte rondom het apparaat is om een goede doorstroming van lucht te waarborgen (tenminste 5 cm achter en 5 cm aan de zijkanten van het apparaat).

Operating Environment

Operating environment temperature and humidity: +5 ºC – +35 ºC (+41 ºF – +95 ºF); less than 85 %RH (cooling vents not blocked) Do not install this unit in a poorly ventilated area, or in locations exposed to high humidity or direct sunlight (or strong artificial light)

D3-4-2-1-7c_A_En

English

WAARSCHUWING

De gleuven en openingen in de behuizing van het apparaat zijn aangebracht voor de ventilatie, zodat een betrouwbare werking van het apparaat wordt verkregen en oververhitting wordt voorkomen. Om brand te voorkomen, moet u ervoor zorgen dat deze openingen nooit geblokkeerd worden of dat ze afgedekt worden door voorwerpen (kranten, tafelkleed, gordijn e.d.) of door gebruik van het apparaat op een dik tapijt of een bed.

D3-4-2-1-7b_A_Du

Milieu de fonctionnement

empérature et humidité du milieu de fonctionnement : De +5 ºC à +35 ºC (de +41 ºF à +95 ºF); Humidité relative inférieure à 85 % (orifices de ventilation non obstrués) N’installez pas l’appareil dans un endroit mal ventilé ou un lieu soumis à une forte humidité ou en plein soleil (ou à une forte lumière artificielle).

D3-4-2-1-7c_A_Fr

Français

Betriebsumgebung

PRECAUCIÓN PARA LA VENTILACIÓN

Cuando instale este aparato, asegúrese de dejar espacio en torno al mismo para la ventilación con el fin de mejorar la disipación de calor (por lo menos 5 cm detrás, y 5 cm en cada lado).

ADVERTENCIA

Las ranuras y aberturas de la caja del aparato sirven para su ventilación para poder asegurar un funcionamiento fiable del aparato y para protegerlo contra sobrecalentamiento. Para evitar el peligro de incendio, las aberturas nunca deberán taparse ni cubrirse con nada (como por ejemplo, periódicos, manteles, cortinas) ni ponerse en funcionamiento el aparato sobre una alfombra gruesas o una cama.

D3-4-2-1-7b_A_Sp

AVVERTENZA PER LA VENTILAZIONE

Installare l’apparecchio avendo cura di lasciare un certo spazio all’intorno dello stesso per consentire una adeguata circolazione dell’aria e migliorare la dispersione del calore (almeno 5 cm sul retro, e 5 cm su ciascuno dei lati).

ATTENZIONE

L’apparecchio è dotato di un certo numero di fessure e di aperture per la ventilazione, allo scopo di garantirne un funzionamento affidabile, e per proteggerlo dal surriscaldamento. Per prevenire possibili pericoli di incendi le aperture non devono mai venire bloccate o coperte con oggetti vari (quali giornali, tovaglie, tende o tendaggi, ecc.), e l’apparecchio non deve essere utilizzato appoggiandolo su tappeti spessi o sul letto.

D3-4-2-1-7b_A_It

Betriebstemperatur und Betriebsluftfeuchtigkeit: 5 ºC bis 35 ºC, 85 % rel. Feuchte max. (Ventilationsschlitze nicht blockiert) Eine Aufstellung dieses Gerät an einem unzureichend belüfteten, sehr feuchten oder heißen Ort ist zu vermeiden, und das Gerät darf weder direkter Sonneneinstrahlung noch starken Kunstlichtquellen ausgesetzt werden.

D3-4-2-1-7c_A_Ge

Condizioni ambientali di funzionamento

Gamma ideale della temperatura ed umidità dell’ambiente di funzionamento: da +5 °C a +35 °C, umidità relativa inferiore all‘85 % (fessure di ventilazione non bloccate) Non installare l’apparecchio in luoghi poco ventilati, o in luoghi esposti ad alte umidità o alla diretta luce del sole (o a sorgenti di luce artificiale molto forti).

D3-4-2-1-7c_A_It

Gebruiksomgeving

emperatuur en vochtigheidsgraad op de plaats van gebruik: +5 °C tot +35 °C, minder dan 85 % RH (ventilatieopeningen niet afgedekt) Zet het apparaat niet op een slecht geventileerde plaats en stel het apparaat ook niet bloot aan hoge vochtigheid of direct zonlicht (of sterke kunstmatige verlichting).

D3-4-2-1-7c_A_Du

Entorno de funcionamiento

emperatura y humedad del entorno de funcionamiento +5 °C a +35 °C ; menos del 85 % de humedad relativa (rejillas de refrigeración no obstruidas) No instale este aparato en un lugar mal ventilado, ni en lugares expuestos a alta humedad o a la luz directa del sol (o de otra luz artificial potente).

D3-4-2-1-7c_A_Sp

Deutsch

Italiano

Nederlands

Español

When using this product follow the instructions written on the underside of the unit, which concern rated voltage, etc.

D3-4-2-2-4_En

Lorsque vous utilisez ce produit, respectez les instructions inscrites sur le fond à propos de la tension nominale et d’autres paramètres.

D3-4-2-2-4_Fr

Beim Gebrauch dieses Gerätes unbedingt die Anweisungen bezüglich der Nennspannung usw. auf dem Aufkleber befolgen, der sich an der Unterseite des Gerätes befindet.

D3-4-2-2-4_Ge

Per il corretto uso di questo apparecchio attenersi alle istruzioni indicate sulla parte inferiore dell’apparecchio stesso, e concernenti la tensione nominale ed altre caratteristiche tecniche.

D3-4-2-2-4_It

Neem bij gebruik van dit apparaat de informatie die aan de onderkant van het apparaat staat in acht (nominale spanning enz.).

D3-4-2-2-4_Du

Cuando emplee este producto, siga las instrucciones escritas en la parte inferior de la unidad, relacionadas con la tensión nominal, etc.

D3-4-2-2-4_Sp

If the AC plug of this unit does not match the AC outlet you want to use, the plug must be removed and appropriate one fitted. Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel. If connected to an AC outlet, the cut-off plug can cause severe electrical shock. Make sure it is properly disposed of after removal. The equipment should be disconnected by removing the mains plug from the wall socket when left unused for a long period of time (for example, when on vacation).

Si la fiche d’alimentation secteur de cet appareil ne convient pas à la prise secteur à utiliser, la fiche doit être remplacée par une appropriée. Ce remplacement et la fixation d’une fiche secteur sur le cordon d’alimentation de cet appareil doivent être effectués par un personnel de service qualifié. En cas de branchement sur une prise secteur, la fiche de coupure peut provoquer une sérieuse décharge électrique. Assurez-vous qu’elle est éliminée correctement après sa dépose. L’appareil doit être déconnecté en débranchant sa fiche secteur au niveau de la prise murale si vous prévoyez une période prolongée de non utilisation (par exemple avant un départ en vacances).

Falls der Netzstecker des Netzkabels dieses Gerätes nicht in die Zusatzsteckdose einer anderen Komponente passt, muss er gegen einen Netzstecker der geeigneten Ausführung ausgewechselt werden. Ein derartiger Austausch des Netzsteckers muss vom Kundendienstpersonal vorgenommen werden. Wenn der vom Netzkabel abgeschnittene ursprüngliche Netzstecker in eine Netzsteckdose eingesteckt wird, besteht akute Stromschlaggefahr! Daher ist unbedingt dafür zu sorgen, dass der abgeschnittene Netzstecker sofort vorschriftsmäßig entsorgt wird. Vor einem längeren Nichtgebrauch des Gerätes, beispielsweise während des Urlaubs, sollte der Netzstecker aus der Netzsteckdose gezogen werden, um das Gerät vollständig vom Netz zu trennen.

Se la spina del cavo di alimentazione di questo apparecchio non si adatta alla presa di corrente alternata di rete nella quale si intende inserire la spina stessa, questa deve essere sostituita con una adatta allo scopo. La sostituzione della spina del cavo di alimentazione deve essere effettuata solamente da personale di servizio qualificato. Dopo la sostituzione, la vecchia spina, tagliata dal cavo di alimentazione, deve essere adeguatamente eliminata per evitare possibili scosse o folgorazioni dovute all’accidentale inserimento della spina stessa in una presa di corrente sotto tensione. Se si pensa di non utilizzare l’apparecchio per un relativamente lungo periodo di tempo (ad esempio, durante una vacanza), staccare la spina del cavo di alimentazione dalla presa di corrente alternata di rete.

Als de netstekker van dit apparaat niet geschikt is voor het stopcontact dat u wilt gebruiken, moet u de stekker verwijderen en een geschikte stekker aanbrengen. Laat het vervangen en aanbrengen van een nieuwe netstekker over aan vakkundig onderhoudspersoneel. Als de verwijderde stekker per ongeluk in een stopcontact zou worden gestoken, kan dit resulteren in een ernstige elektrische schok. Zorg er daarom voor dat de oude stekker na het verwijderen op de juiste wijze wordt weggegooid. Haal de stekker van het netsnoer uit het stopcontact wanneer u het apparaat geruime tijd niet denkt te gebruiken (bijv. wanneer u op vakantie gaat).

Si la clavija del cable de alimentación de CA de este aparato no se adapta a la toma de corriente de CA que usted desea utilizar, deberá cambiar la clavija por otra que se adapte apropiadamente. El reemplazo y montaje de una clavija del cable de alimentación de CA sólo deberá realizarlos personal de servicio técnico cualificado. Si se enchufa la clavija cortada a una toma de corriente de CA, puede causar fuertes descargas eléctricas. Asegúrese de que se tira de la forma apropiada después de haberla extraído. El aparato deberá desconectarse desenchufando la clavija de la alimentación de la toma de corriente cuando no se proponga utilizarlo durante mucho tiempo (por ejemplo, antes de irse de vacaciones).

D3-4-2-2-1a_A_En

D3-4-2-2-1a_A_Fr

D3-4-2-2-1a_A_Ge

D3-4-2-2-1a_A_It

D3-4-2-2-1a_A_Du

D3-4-2-2-1a_A_Sp

CAUTION

The POWER switch on this unit will not completely shut off all power from the AC outlet. Since the power cord serves as the main disconnect device for the unit, you will need to unplug it from the AC outlet to shut down all power. Therefore, make sure the unit has been installed so that the power cord can be easily unplugged from the AC outlet in case of an accident. To avoid fire hazard, the power cord should also be unplugged from the AC outlet when left unused for a long period of time (for example, when on vacation).

ATTENTION

L’interrupteur POWER de cet appareil ne coupe pas complètement celui-ci de sa prise secteur. Comme le cordon d’alimentation fait office de dispositif de déconnexion du secteur, il devra être débranché au niveau de la prise secteur pour que l’appareil soit complètement hors tension. Par conséquent, veillez à installer l’appareil de telle manière que son cordon d’alimentation puisse être facilement débranché de la prise secteur en cas d’accident. Pour éviter tout risque d’incendie, le cordon d’alimentation sera débranché au niveau de la prise secteur si vous prévoyez une période prolongée de non utilisation (par exemple avant un départ en vacances).

ACHTUNG

Der POWER-Schalter dieses Gerätes trennt das Gerät nicht vollständig vom Stromnetz. Um das Gerät vollständig vom Netz zu trennen, muss der Netzstecker aus der Netzsteckdose gezogen werden. Daher sollte das Gerät so aufgestellt werden, dass stets ein unbehinderter Zugang zur Netzsteckdose gewährleistet ist, damit der Netzstecker in einer Notsituation sofort abgezogen werden kann. Um Brandgefahr auszuschließen, sollte der Netzstecker vor einem längeren Nichtgebrauch des Gerätes, beispielsweise während des Urlaubs, grundsätzlich von der Netzsteckdose getrennt werden.

AVVERTENZA

L’interruttore principale (POWER) dell’apparecchio non stacca completamente il flusso di corrente elettrica dalla presa di corrente alternata di rete. Dal momento che il cavo di alimentazione costituisce l’unico dispositivo di distacco dell’apparecchio dalla sorgente di alimentazione, il cavo stesso deve essere staccato dalla presa di corrente alternata di rete per sospendere completamente qualsiasi flusso di corrente. Verificare quindi che l’apparecchio sia stato installato in modo da poter procedere con facilità al distacco del cavo di alimentazione dalla presa di corrente, in caso di necessità. Per prevenire pericoli di incendi, inoltre, il cavo di alimentazione deve essere staccato dalla presa di corrente alternata di rete se si pensa di non utilizzare l’apparecchio per periodi di tempo relativamente lunghi (ad esempio, durante una vacanza).

LET OP

De POWER schakelaar van dit apparaat koppelt het apparaat niet volledig los van het lichtnet. Aangezien er na het uitschakelen van het apparaat nog een kleine hoeveelheid stroom blijft lopen, moet u de stekker uit het stopcontact halen om het apparaat volledig van het lichtnet los te koppelen. Plaats het apparaat zodanig dat de stekker in een noodgeval gemakkelijk uit het stopcontact kan worden gehaald. Om brand te voorkomen, moet u de stekker uit het stopcontact halen wanneer u het apparaat langere tijd niet denkt te gebruiken (bijv. wanneer u op vakantie gaat).

PRECAUCIÓN

El interruptor de la alimentación POWER de este aparato no corta por completo toda la alimentación de la toma de corriente de CA. Puesto que el cable de alimentación hace las funciones de dispositivo de desconexión de la corriente para el aparato, para desconectar toda la alimentación del aparato deberá desenchufar el cable de la toma de corriente de CA. Por lo tanto, asegúrese de instalar el aparato de modo que el cable de alimentación pueda desenchufarse con facilidad de la toma de corriente de CA en caso de un accidente. Para evitar correr el peligro de incendio, el cable de alimentación también deberá desenchufarse de la toma de corriente de CA cuando no se tenga la intención de utilizarlo durante mucho tiempo seguido (por ejemplo, antes de irse de vacaciones).

D3-4-2-2-2a_A_It

D3-4-2-2-2a_A_En

D3-4-2-2-2a_A_Fr

D3-4-2-2-2a_A_Ge

D3-4-2-2-2a_A_Du

D3-4-2-2-2a_A_Sp

Before Operating

Thank you for buying this Pioneer product. Please read through these operating instructions so you will know how to operate your model properly. After you have finished reading the instructions, put them away in a safe place for future reference. In some countries or regions, the shape of the power plug and power outlet may sometimes differ from that shown in the explanatory drawings. However the method of connecting and operating the unit is the same.

K015 En

If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling.

Private households in the 25 member states of the EU, in Switzerland and Norway may return their used electronic products free of charge to designated collection facilities or to a retailer (if you purchase a similar new one). For countries not mentioned above, please contact your local authorities for the correct method of disposal. By doing so you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health.

Contents

Before Operating

Features ................................................................................... 2

Handling Precautions ............................................................... 4

Discs Usable with This Unit ..................................................... 5

Names and Functions of Parts ................................................. 8

Operation panel .................................................................. 8

Display .............................................................................. 10

Jog dial display ................................................................. 11

Rear panel ........................................................................ 11

Main video output (VIDEO OUT) and preview video output

(PREVIEW OUT) ............................................................... 12

Connections ........................................................................... 13

1. Connections to a Pioneer DJ mixer (sold separately)

(audio output and control connector) ........................... 13

2. Control cord connection for relay play ......................... 14

3. Connection to stereo amplifier (without DJ mixer) ...... 14

4. Connection to component equipped

with digital input connector.......................................... 14

5. Connection to television monitor

(composite video/S-Video) ........................................... 15

6. Connection to video mixer ........................................... 16

7. Connecting the power cord ......................................... 16

Preparations

Setup ...................................................................................... 17

TV system setting for video output .................................. 17

How to perform setup ...................................................... 17

Using the Setup Navigator ............................................... 17

Setup Menu items ............................................................ 19

To return all settings to their factory defaults ................... 20

Using the Setup Menu ..................................................... 20

Advanced settings ............................................................ 21

Adjusting Dolby Digital audio ............................................ 21

Digital output setting ........................................................ 21

[Audio2] settings .............................................................. 22

[Video1] settings ............................................................... 23

Video quality adjust........................................................... 24

[Video2] settings ............................................................... 25

[Language] Settings .......................................................... 26

Setting Parental Lock ....................................................... 29

Basic Operations

Loading and Removing Discs ................................................. 31

Basic Operations .................................................................... 32

Beginning playback ........................................................... 32

Auto cue function ............................................................. 33

To stop playback ............................................................... 33

To eject the disc ............................................................... 33

To temporarily interrupt playback (pause mode) ............... 33

To change language/subtitle settings during playback

(DVD only) ........................................................................ 33

Changing the viewing angle (DVD only) ........................... 34

Fast forward/fast reverse ................................................. 34

Track search (skip) ............................................................ 35

Title search (DVD only) ..................................................... 35

Folder search (MP3 only) .................................................. 35

Setting cue points ............................................................ 36

Changing playback speed ................................................. 36

Setting master tempo ...................................................... 37

Jog dial functions ............................................................. 37

Jog sensitivity adjustment ................................................ 37

About the WAVE display ................................................... 37

About the TEXT display .................................................... 38

Mixing different tracks (splicing) ...................................... 38

Advanced Operations

Advanced Operations ............................................................. 39

Scratch play ...................................................................... 39

Hyper jog mode ................................................................ 39

Spin play ........................................................................... 39

Braking ............................................................................. 39

Hot cue ............................................................................. 39

Loop playback ................................................................... 40

Back & Forth Loop Mode ................................................. 41

Reverse play ..................................................................... 41

About fader start play ....................................................... 41

Relay play with two players .............................................. 41

Selecting tracks with MP3 navigator (MP3 only) .............. 42

To view guide displays ...................................................... 42

Operations Using Memory Cards........................................... 43

Recording to memory cards ............................................. 43

To recall data recorded on memory cards ........................ 44

To delete information recorded on memory cards ........... 46

To copy memory card data ............................................... 46

Other

Troubleshooting ...................................................................... 47

Error message display ...................................................... 49

Dot Matrix Guide Display Messages...................................... 50

Specifications ......................................................................... 51

English

Français

Deutsch

Italiano

Nederlands

Español

<DRB1414> En

Before Operating (Features)

Features

This player has been designed to provide CD/DVD playback features and functions demanded by professional disco club DJs and VJs. It is a professional DVD player equipped with operational ease, sound quality, and functions superior to those found on the professional analog players conventionally used by DJs.

JOG DIAL

HOT CUE

Up to 3 hot cue points (A, B, C) can be recorded in advance and called up later for instant playback from those points. Hot cues can be used not only to record normal cue points, but also for loop point playback.

Large-diameter (206 mm) dial for operating sensitivity exceeding that possible with conventional analog turntables

¶ PITCH BEND

Changes playback pitch in proportion to the direction and speed of jog dial rotation.

¶ SCRATCH PLAY

In VINYL mode, when the top surface of the jog dial is touched, playback stops and starts in response to the direction and speed of jog dial rotation. The user can also adjust the sensitivity of start-up when the jog dial is touched and released, making possible new DJ techniques.

¶ FRAME SEARCH

When the jog dial is rotated during pause, the pause position is changed in units of individual frames (1/75th second).

¶ SUPER FAST SEARCH

When the jog dial is rotated while depressing the manual search button, track search button or title/folder search button, the search will be performed more quickly than the conventional search or track search (or title/chapter search) functions.

¶ HYPER JOG MODE

In VINYL mode, when the jog dial is rotated, the amount of sound or image change quadruples (x4) in response to the rotation. Performance possibilities are enhanced by employing this function together with the ordinary mode.

REVERSE PLAY

By pulling the DIRECTION select switch toward the front (REV position), tracks can be played in reverse.

TEMPO CONTROL

High-performance 100 mm slider for precise adjustment of track speed

Using a digital display with 0.02 % increments (within control range ±6 %), the user can accurately and easily match the tempos of playback tracks.

¶ TEMPO CONTROL RANGE

Four tempo control ranges are provided: ±6 %, ±10 %, ±16 %, and WIDE.

¶ TEMPO CONTROL RESET

This control allows tempo to be reset to the default 0 % status instantly, regardless of the slider position.

¶ MASTER TEMPO

Allows pitch to be maintained while changing track speed.

JOG ADJUST

This function allows you to adjust the felt resistance when rotating the jog dial.

ON JOG DISPLAY

The center of the jog dial is furnished with a display providing variety of information, including disc status, cue point position, audio/ video memory status, jog touch detect display, and VINYL mode.

WAVE DISPLAY

With an analog record, the user could look for the breaks in the grooves to use as mix points and end points. In the same way, the WAVE display reveals track breaks in advance, allowing the DJ to use them as break points.

CUE/LOOP MEMORY

Cue points and loop points can be recorded for each disc on external SD memory cards or Multimedia cards (MMC), and recalled later as desired.

CUE

¶ BACK CUE

By previously recording a cue point, it can be returned to instantly by pressing the CUE button during subsequent playback, thus starting playback again from that point.

¶ AUTO CUE

This function cues a track by skipping the non-recorded portion before the beginning of music, setting the player to standby mode immediately before music begins. In this way, playback can begin instantly when the PLAY/PAUSE (6) button is pressed.

¶ CUE POINT SAMPLER

This function allows one-touch playback from the cue points stored in memory, a convenient function for confirming cue points and sampling the points stored.

REAL TIME SEAMLESS LOOP

Allows simple setting and canceling of playback loops. Loops can be set quickly during track playback; also allows quick setting of a loop immediately before the end of a track, thus preventing the track from ending. In addition, loop functions have been facilitated by the addition of an ADJUST mode that allows one-touch modification of loop-in and loop-out points.

En <DRB1414>

Before Operating (Features)

RELOOP

Once set, a loop can be returned to any number of times

After canceling loop play, pressing the RELOOP/EXIT button causes playback to return and begin again from the previously set loop. Turning the function ON/OFF in time with the track’s rhythm allows a variety of new performance possibilities.

4-BEAT LOOP

When the 4-BEAT/ONE-TRACK button is pressed, the point at which the button is pressed is set as a loop-in point, and a loop-out point is set automatically 4 beats later, and automatic loop play is performed.

ONE-TRACK LOOP

When the 4-BEAT/ONE-TRACK button is held depressed for one second or more, the chapter loop or track loop function is enabled.

BACK & FORTH LOOP

The Back & Forth Loop mode repeats playback in forward direction from the loop-in point to loop-out point, followed by reverse play from the loop-out point to the loop-in point.

PREVIEW MONITOR OUTPUT

This is an auxiliary video output that produces an overlay display of operating information on the main video output screen, and provides the DJ with a visual aids when operating the unit. During use of DVD play, cue points, loop points, and hot-cue points are shown as thumbnail displays overlain on the main output making possible interactive DJ operations.

LEGATO PRO

The player is equipped with a digital filter that uses up-sampling technology (DVD: 48 kHz \ 192 kHz; CD: 44.1 kHz \ 176.4 kHz) for reproducing audio information lost in some disc (DVD, CD) formats.

HI-BIT

This function extends the bit length of audio data. By transforming 16-bit or 20-bit data to 24-bit, even minute signals can be reproduced with smooth, finely defined sound.

DIGITAL AUDIO OUT

96 kHz 24-bit digital audio output is supported in DJ mode as well as NORMAL mode.

English

PLAYING ADDRESS

With an analog record, the position of the stylus gives the operator an immediate grasp of the progress of playback. In the same way, the play address display shows a bar graph that provides an immediate visual grasp of the track’s playback progress. The current position in the track is indicated by the length of the bar; in addition, the bar flashes to warn that playback is approaching the end of the track.

FADER START

When the player is connected to a Pioneer DJ mixer (sold separately), the mixer’s fader operation can be used to perform fader start and back cue.

MULTI READ

Discs readable on this player include CD-R/CD-RW (recorded in audio CD format or MP3), and DVD-R/DVD-RW (recorded in video format or MP3). However, since this player uses high-speed data read for the purposes of its DJ operations, some discs may not play back properly depending on the characteristics of the disc and the recorder, as well as a result of dirt or scratches on the disc, etc.

MP3 DJ PLAY

This function allows use of the DJ function to play MP3 files recorded on CD or DVD.

About DVD playback in DJ mode

Since various special operations are supported in DJ mode, certain limitations are placed on normal playback functions such as SCAN. For this reason, operations which are possible in the NORMAL mode may be limited or disabled when attempted in DJ mode. In short, if you wish to use all ordinary DVD play functions, use the NORMAL mode.

Limited or disabled functions (when in DJ mode)

¶ Cannot play sub-pictures (can’t display subtitles or onscreen but-

tons)

¶ Cannot use password input command (when using interactive

commands, the same operations may not produce the same results as when in NORMAL mode).

¶ May only play midway through titles. ¶ May skip certain parts of titles. ¶ Playback may be temporarily interrupted when switching audio

functions.

¶ Playback may be temporarily interrupted when changing view-

ing angle.

¶ Cannot use pan-and-scan function. ¶ The title itself may disallow use of DJ operations. In this case,

DJ operations are prohibited, and the same operations are performed as when in NORMAL mode.

<DRB1414> En

Before Operating (Handling Precautions)

Handling Precautions

Installation location

¶ Placing and using the player for long periods on heat-generat-

ing sources such as amplifiers or near spotlights, etc. will affect product performance. Avoid placing the player on heatgenerating sources.

¶ Install this player as far as possible away from tuners and TV

sets. The player installed in close proximity to such equipment may cause noise or degradation of the picture. Noise may be noticeable when an indoor antenna is used. In such cases, make use of an outdoor antenna or turn off power to the player.

¶ When the unit is used in a loud-sound environment, e.g., near

a speaker, sound skip may occur. Install the unit away from the speaker or reduce the listening volume.

¶ Place this unit on a level surface and a stable platform.

Take adequate note of the following precautions when preparing a place for installation:

Be sure the player, including its video, audio and power supply cords, does not touch vibrating materials. Any vibration other than that transmitted through the insulators may cause the disc to skip. Take special care when using the player while it is installed in a carrying case.

Do not place on or against vibrating materials!

About the carrying case

The upper surface of the jog dial is equipped with a touch-sensitive switch. When placing the player in its carrying case, avoid placing any pressure on the jog dial.

Condensation

When this unit is brought into a warm room from previously cold surroundings or when the room temperature rises sharply, condensation may form inside the unit and impair its performance. In such cases, disconnect the power cord and allow the unit to set for 1 to 2 hours, or raise the room temperature gradually before playing.

Cleaning the player

To clean the player wipe with a polishing or a soft, dry cloth. For stubborn dirt, moisten a soft cloth with a weak solution of neutral detergent (diluted in five to six parts water), wring the cloth well, and wipe away the dirt. Use a dry cloth to wipe the surface dry. Do not use volatile liquids such as benzene or thinner which will damage the unit.

About the lens cleaner

The player's pickup lens should not become dirty in normal use. If for some reason, the lens becomes soiled and malfunctions, contact your nearest PIONEER authorized service center. Lens cleaners for DVD (CD) players are commercially available, but special care should be exercised in their use as some may cause damage to the lens.

Leave space to allow for heat dissipation.

DVJ-1000

Leave space to allow for heat dissipation.

CUE

Leave space to allow for heat dissipation.

Moving the unit

■ Never move the unit during playback!

During playback, a disc rotates at very high speed; moving the player during playback may result in scratches or other damage to the disc.

■ When moving the unit is necessary

Before moving the unit, remove any disc and disconnect the power. Malfunctions or damage may result if the unit is moved with a disc loaded. Also take care to prevent exposing the unit to heat or moisture during transport.

POWER-CORD CAUTION

Handle the power cord by the plug. Do not pull out the plug by tugging the cord and never touch the power cord when your hands are wet as this could cause a short circuit or electric shock. Do not place the unit, a piece of furniture, etc., on the power cord, or pinch the cord. Never make a knot in the cord or tie it with other cords. The power cords should be routed such that they are not likely to be stepped on. A damaged power cord can cause a fire or give you an electrical shock. Check the power cord once in a while. When you find it damaged, ask your nearest PIONEER authorized service center or your dealer for a replacement.

S002_En

Regarding data recorded on memory cards

It is the users responsibility to make regular backups of important memory card data. Pioneer disclaims any responsibility for damage to or loss of memory card data, or other incidental damages arising from incompatibilities of the player and memory card, static electricity or other external causes.

Lawful use of DVJ-1000: Copyright etc

Neither Pioneer nor its dealers are responsible for the use made of the DVJ-

1000. The user must ensure it has all relevant licences and consents in place (whether for copyright/public performance, performers rights, moral rights or otherewise) to allow the lawful use of the DVJ-1000. This is likely to include licences from organisations administering performance rights in audio or video recordings or consents from any other relevant rights holders.

En <DRB1414>

Discs Usable with This Unit

Before Operating (Discs Usable with This Unit)

Types of discs playable on this unit

The following marks and logos are displayed on disc labels, packaging, or jackets.

Types and Logos of playable discs

DVD video

DVD-R

(Note 1)

CD CD-TEXT

DVD-RW

(Note 3)

Note 1) About DVD-R disc playback:

This player can play back DVD-R discs recorded in “DVD video” format or MP3.

Note 2) About DVD-RW disc playback:

¶ This player can play back DVD-RW discs recorded in “DVD

video” format or MP3.

¶ When playing a disc that has been edited on a DVD recorder,

portions of the recording including links between tracks may appear as a momentary still image.

¶ When playing a disc that has been recorded or edited on a

DVD recorder, the locations of edited portions may shift somewhat.

* For details, consult the Operating Instructions for your recorder.

Note 3) Regarding CD-TEXT display:

The number of characters that can be displayed is up to 72 for disc title, and 48 for track titles. Displays of 15 characters or more will scroll. Only alpha-numerics and a limited number of symbols can be displayed.

Note 4) CD-R/CD-RW discs:

This player supports playback of CD-R/CD-RW discs recorded in audio CD format or MP3. * For details, consult the Operating Instructions for your recorder.

When playing 8 cm CDs, always use an 8 cm CD adapter

P. 31).

(☞

Note:

This player does not support playback of 8 cm DVDs. Do not attempt to use adapters meant for 8 cm CDs, since the adapter may come loose during rotation, causing damage to the disc or player.

is a trademark of DVD Format/Logo Licensing Corporation.

CD-R

(Note 2)

(Note 4)

CD-RW

(Note 4)

■ The following discs cannot be played on this unit:

¶ DVD video discs not marketed for region “2” or “ALL” ¶ DVD-R/DVD-RW discs recorded in VR format ¶ DVD audio discs ¶ DVD-ROM/DVD-R/DVD-RW discs containing no MP3 files ¶ DVD-RAM ¶ Video CDs ¶ CD-ROM/CD-R/CD-RW discs containing no MP3 files ¶ Photo CD ¶ DTS-CD, etc.

Notes:

Some DVD-R/DVD-RW and CD-R/CD-RW discs recorded on standalone recorders or computer drives may not be playable back on this player, due to a variety of reasons, including disc characteristics, scratches, dirt, player lens dirt or condensation, etc.

Some discs recorded on computer drives may not be playable on this player, depending on the recording application used, its settings, and operating environment. Be sure to use the correct formatting for the discs used. For details, consult the application author.

This unit cannot play DVD-R/DVD-RW discs recorded in video format unless they have been finalized.

This unit cannot play DVD-R/DVD-RW discs recorded in VR format.

This unit cannot play partially recorded CD-R/CD-RW discs that have not been finalized.

For detailed information regarding the handling of DVD-R/DVDRW and CD-R/CD-RW discs, consult the handling precautions printed on the disc case or otherwise supplied with each disc.

■ Regarding copy-control CDs

This unit is designed to conform with audio CD standards. Operation is not guaranteed when playing CDs produced outside the normal CD standards.

■ About DualDisc playback

A DualDisc is a new two-sided disc, one side of which contains DVD content – video, audio, etc. – while the other side contains non-DVD content such as digital audio material. The non-DVD, audio side of the disc is not compliant with the CD Audio specification and therefore may not play. The DVD side of a DualDisc plays in this product. DVD-Audio content will not play. For more detailed information on the DualDisc specification, please refer to the disc manufacturer or disc retailer.

■ Regarding DVD-R/DVD-RW, CD-R/CD-RW discs

Due to the unique construction of DVD-R/DVD-RW and CD-R/ CD-RW discs, leaving them for extended periods of time in the pause (or cue standby) mode at a single point may result in the discs’ becoming difficult to play at that place. The same symptom may also occur if the loop function is used to play back a single point on the disc excessively. As a result, users are advised to construct backup archive discs when playing discs containing important data.

English

<DRB1414> En

Before Operating (Discs Usable with This Unit)

Marks displayed on DVD

The following symbols and marks may be displayed on DVD labels or packaging:

Mark Meaning

16 : 9 LB

ALL

Number of recorded audio tracks

Number of recorded subtitles

Number of recorded angles

Recorded aspect ratio

Region number. This player can play discs marked with region “2” or “ALL”.

Playing MP3 files

MP3 files must follow the format requirements listed below.

MP3 format

Disc format

MPEG-1

MPEG-2

ID3 tag

File extension

Folder levels

Maximum number of folders

Maximum number of files

CD-R/CD-RW recording mode

DVD-R/DVD-RW recording mode

DVD operating limitations

Some DVDs are designed explicitly to prevent the use of certain operations or to prevent changing operation methods. As a result, the methods used to operate each disc may vary, and some techniques may not be usable with certain discs. In the event that a prohibited technique is attempted with a disc on this player, the display will show the disc operation prohibited mark

. Also, certain other operations may not be supported on discs that support menus or dialogue-type operations during playback. In such cases, the player operation prohibited mark

will be displayed.

Regarding copyright

¶ Unauthorized copying, broadcasting, public performance, or

rental of copyrighted discs is prohibited by law.

¶ This product incorporates copyright protection technology

that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

Supports Audio Layer-3 sampling frequency 32 kHz, 44.1 kHz, 48 kHz, Bit Rate 32 Kbps to 320 Kbps.

Supports Audio Layer-3 sampling frequency 16 kHz, 22.05 kHz, 24 kHz, Bit Rate 16 Kbps (stereo) to 160 Kbps.

Supports ID3 Vers. 1.0/1.1/2.2/2.3/2.4. Displays title, artist, album.

.mp3, .MP3, .mP3, .Mp3

Maximum of 8 folders. Files located in folders exceeding 8 levels cannot be played.

99 (99 folders + 1 root)

999 (per folder)

Record in accordance with ISO9660 file system standards. Supports only Disc At Once or Track At Once. DVJ-1000 does not support Packet Write recorded discs.

Record in accordance with ISO9660 file system standards. Does not support multi-border recording.

* This unit is not equipped with a sort function allowing playback by order of file names or ID3 tags. Playback is performed in the

order tracks are recorded on the disc. * Plays MP3 files stored on CD or DVD. Cannot play MP3 files stored on SD memory cards or Multimedia cards (MMC). * Startup time increases with the number of folders.

En <DRB1414>

Before Operating (Discs Usable with This Unit)

Disc composition

Digital Versatile Discs (DVD)

DVD video, DVD-R or DVD-RW discs are recorded in units called “titles,” with each title being divided into one or more sub-divisions called “chapters.” Further, some, discs are furnished with menus for navigating the disc, but menus may not be included with all titles. In the case of commercial films, a single movie normally corresponds to a single title. On so-called “karaoke” discs, each song track composes a single title, although there are some exceptions to this rule, so care is needed when using search functions.

Title 1 Title 2

Chapter 1 Chapter 2 Chapter 1 Chapter 2

DVD/DVD-R/DVD-RW

Compact Discs (CD)

In the case of compact discs, each disc is divided into units of individual tracks (normally, each song is contained on a single track). In addition, tracks may have sub-divisions called index numbers.

Track 1 Track 2 Track 3 Track 4 Track 5

Handling discs

■ When holding discs, do not touch their signal surfaces. Hold by the edges, or by one edge and the center hole.

English

■ Do not affix gummed labels or tape to the disc surface. Also, do not scratch or damage the label.

■ Discs rotate at high speeds inside the player. Do not use damaged, cracked or warped discs.

■ Do not play a disc with a special shape

¶ Do not play a disc having other shape than a circular disc,

such as heart shaped disc. Otherwise malfunction may occur.

■ Storing discs

¶ Discs are made of the same kinds of plastic used for con-

ventional analog audio records. Be careful not to allow discs to warp. Always store discs in their cases vertically, avoiding locations with high heat, humidity, or extremely low temperatures. Avoid leaving discs in cars; the interior of a car in direct sunlight can become extremely hot.

¶ Always read and abide by the precautionary notes listed on

disc labels.

■ Cleaning discs

¶ Always keep your discs clean by wiping them gently with a

soft cloth from the inner edge toward the outer edge.

¶ When cleaning discs, the use of a commercial CD/DVD clean-

ing kit is recommended.

¶ If a disc becomes very dirty, dampen a soft cloth with water,

(be sure to wring it out well) and wipe the away dirt gently. Remove any water drops with another soft, dry cloth.

¶ Do not use record cleaning sprays or anti-static agents on discs.

Never clean discs with benzene, thinner, or other volatile solvents or damage to the disc surface may result.

<DRB1414> En

Before Operating (Names and Functions of Parts)

Names and Functions of Parts

Operation panel

Buttons and controls with the mark are disabled when the NORMAL/DJ switch is set to NORMAL. Buttons and controls with the

mark are disabled when the NORMAL/DJ switch is set to DJ.

DELETE

MEMORY MENU T.MENU

CUE / LOOP

CALL

53525150 54

DVJ-1000

JOG ADJUST

LIGHT

45 44

40 39

12 35678

46 4748

OFF ON

POWER

TIME

AUTO

MODE

CUE

TEXT MODE

DIRECTION

REV

MP3 FOLDER

HOT CUE

DVD TITLE

FWD

REC MODE

FWD

REV

ANGLE SUBTITLE AUDIO

REALTIME CUE

IN ADJUST

BACK & FORTH

OUT ADJUST

DISPLAY

RELOOP/

OUT

LOOP

4-BEAT

EXIT

ONE-TRACK

37 36

CUE

PLAY/PAUSE

REV

FWD

34 33

32 31

1. POWER OFF (—)/ON (_) switch

Located on the rear panel.

2. Loop in/realtime cue/loop in point adjust button/indicator (IN/REALTIME CUE/IN ADJUST)

Real time cue ☞ P.36 Loop-in point input ☞ P.40 Loop-in point adjust ☞ P.40

3. Loop out/loop out point adjust button/indicator (OUT/OUT ADJUST)

Loop-out point input ☞ P.40 Loop-out point adjust ☞ P.40

4. BACK & FORTH button ☞ P.41

Use to switch between normal loop mode and back & forth loop mode.

5. Loop mode indicator ☞ P.41

Lights during back & forth loop mode.

6. RELOOP/EXIT button/indicator ☞ P.40

En <DRB1414>

7. 4-BEAT/ONE-TRACK button ☞ P.41

• 4-Beat Loop

When this button is pressed, loop play will begin with that point as the loop-in point, and the loop-out automatically point set 4 beats later.

STOP

UNLOCK

LOCK

EJECT

13 14

RETURN

ENTER

SETUP

TOUCH/BRAKE

55 56

RELEASE/START

HEAVY

HYPERJOG MODE

16 17

VINYL

WIDE

JOG MODE

TEMPO

MASTER TEMPO

19 20

21 22

• One-Track Loop

When this button is held depressed for 1 second or more, the chapter loop or track loop play will begin.

8. CUE/LOOP CALL button ☞ P.44

Press to turn cue point navigation mode ON/ OFF.

9. Cursor button ( / / / )

This button is used for cue point navigation; during MP3 playback, functions for performing selections with MP3 navigator, and for making various DVD settings.

10. ENTER button

This button is used for cue point navigation; during MP3 playback, functions for performing selections with MP3 navigator, and for making various DVD settings.

11. NORMAL/DJ switch ☞ P.14

Located on the rear panel.

12. STOP button

Stops disc playback. When the eject/stop mode select switch is set to LOCK, playback will not stop unless the PAUSE mode is set first.

TEMPO RESET

13. Eject/stop mode select switch (UNLOCK/LOCK)

UNLOCK: If the EJECT (0) button is pressed

during playback, the disc stops and is ejected. If the STOP button is pressed during playback, the disc playback stops.

TEMPO

LOCK: If the EJECT (0) button is pressed dur- ing playback, the disc will not be ejected. To eject the disc, set the unit to pause, then press the EJECT (0) button. Likewise, playback will

252627282930

not stop if the STOP button is pressed during playback; to stop disc playback, set the unit to pause, then press the STOP button.

14. EJECT (0) button

When this button is pressed, disc rotation stops and the disc is ejected from the loading slot. If

the eject/stop mode select switch is set to the LOCK position, the disc will not be ejected unless the unit is set to pause before pressing the EJECT (0) button (☞ P.31).

15. TOUCH/BRAKE response dial

Adjusts the disc deceleration speed (time to playback stop) when the jog dial’s top surface is touched with jog mode set to VINYL ON. Rotate the dial counterclockwise to stop playback quickly, and rotate dial clockwise to cause slower deceleration.

16. RELEASE/START response dial

Adjusts the disc acceleration speed (playback startup time) when the jog dial’s top surface is released with jog mode set to VINYL ON. Rotate the dial counterclockwise to restart playback quickly, and rotate dial clockwise to cause slower acceleration.

17. JOG ADJUST dial

Use to adjust the felt resistance (light/heavy) of the jog dial when it is rotated.

18. HYPERJOG MODE button/indicator

When hyper jog mode is set to ON with jog mode set to VINYL ON, turning the jog dial causes the rate of change of image and sound to increase to 4x the rate of changed normally produced (when the hyper jog mode is OFF).

Before Operating (Names and Functions of Parts)Before Operating (Names and Functions of Parts)

19. JOG MODE select button

Each time pressed, sets VINYL mode alternately ON/OFF. VINYL mode ON: If surface of jog dial is touched during playback, playback stops, and if the dial is then rotated, image and sound are output in response to the amount of rotation. (if the angled surface of the jog dial is rotated without touching the top, pitch bend operation is enabled.) ¶ The current jog mode is memorized even when power is turned

off.

VINYL mode OFF: The above operations are disabled even when the jog dial’s surface is touched.

20. VINYL mode indicator

Lights when the jog mode is set to VINYL mode.

21. TEMPO control range select button

Each time this button is pressed, the TEMPO control slider’s vari- able range changes (±6 %, ±10 %, ±16 %, WIDE). When WIDE is selected, the variable range during DVD and MP3 playback is set to +70 % to –100 %, and during CD playback, ±100 %.

22. TEMPO control range indicator (±6, ±10, ±16, WIDE)

¶ When control range is set to ±6 %, the ±6 indicator lights. ¶ When control range is set to ±10 %, the ±6 and ±10 indicators

light.

¶ When control range is set to ±16 %, the ±6, ±10 and ±16 indica-

tors light.

¶ When control range is set to WIDE, the ±6, ±10, ±16 and WIDE

indicators light.

23. MASTER TEMPO button/indicator ☞ P.37

Each time this button is pressed, the master tempo function turns alternately ON/OFF.

24. TEMPO control slider

When pulled forward (+), playback tempo is accelerated, and when pushed away (–), tempo is slowed.

25. TEMPO RESET indicator

When lighted, indicates that the playback tempo is set to normal tempo “0”, regardless of the position of the TEMPO control slider.

26. TEMPO RESET button

Pressing this button instantly resets the playback tempo to “0” (normal tempo), regardless of the current position of the TEMPO control slider. Press the button once again to cancel the reset.

27. Jog dial display ☞ P.11

28. Jog dial (+FWD/–REV) ☞ P.37

29. Disc loading slot ☞ P.31

30. Forced eject hole ☞ P.31

31. Memory card door and slot ☞ P.43

32. Memory card indicator ☞ P.43

This indicator lights with a memory card is loaded and the door is closed, and flashes during memory card access. ¶ Do not open the door or turn off power while the indicator is flash-

ing.

33. PLAY/PAUSE indicator

Lights during playback, and flashes during pause mode.

34. PLAY/PAUSE (3/8) button ☞ P.33

35. CUE indicator ☞ P.36

Lights to indicate a cue point has been set. Flashes during pause mode.

36. CUE button ☞ P.36

Cue point setting Back cue Cue point sampler

37. Manual search buttons (REV1/FWD¡) ☞ P.34

38. Track search buttons (PREVIOUS 4/NEXT ¢)

Use to return/advance playback by track (during CD, MP3) or chapter (during DVD). During DVD playback, use to return to menu page or change page.

☞ P.35

39. REV indicator

Lights when DIRECTION FWD/REV select switch is set to reverse.

40. DIRECTION FWD/REV select switch

Set to REV position for reverse playback.

41. HOT CUE REC MODE button ☞ P.39

Press to select the HOT CUE button’s function (record/call).

¶ Defaults to call mode when power is switched on.

42. HOT CUE (A, B, C) buttons/indicators ☞ P.39

A, B, or C indicator lights red to indicate hot cue point record mode. A, B, or C indicator lights green for hot cue point, and orange for hot loop point; when an indicator is lighted, call mode is enabled for that point; pressing the button initiates playback from the hot cue point. When indicator is not lighted, no hot cue point is recorded.

43. Title/folder search buttons (DVD TITLE/MP3 FOLDER |/\) ☞

During DVD playback, titles are forwarded or reversed in the direction corresponding to the button pressed. During MP3 playback, goes in designated direction for folders in layered CD or DVD.

P.35

44. TEXT MODE select button ☞ P.38

Each time this button is pressed, the display alternates between WAVE and TEXT (track name/album name/artist name).

45. TIME MODE/AUTO CUE button

TIME MODE:

Each time the button is pressed, the time display switches alternately between playback elapsed time and remaining time (REMAIN). In the case of MP3, the remaining playtime (REMAIN) may not immediately be displayed, depending on the file. ¶ The time mode remains set in memory even when power is turned

off.

AUTO CUE:

Hold depressed for one second or more to set/release the auto cue function. Hold depressed for five seconds or more to switch the auto cue level (☞ P.33). ¶ The auto cue ON/OFF setting and auto cue level remains set in

memory even when power is turned off.

46. ANGLE button

Press to change the viewing angle during DVD playback (on supported discs only). ¶ In DJ mode, when the angle is changed both video and audio

playback temporarily stop (due to writing to buffer memory).

47. SUBTITLE button

During DVD playback, press to alternately turn subtitle display ON/ OFF (on supported discs only). ¶ This function is disabled in DJ mode.

48. AUDIO button

During DVD playback, press this button to change language or audio channel (on supported discs only). ¶ In DJ mode, when the language/audio channel is changed, both

video and audio playback temporarily stop (due to writing to buffer memory).

49. Display ☞ P.10 (1 to 24)

50. DISPLAY button ☞ P.42

When pressed in DJ mode, turns the hot cue, cue point, and playback time guide display ON/OFF on the monitor connected to the preview video output connector. When pressed in NORMAL mode, turns the disc information guide display ON/OFF. ¶ When power is switched ON, the display function defaults to ON

when the unit is in the DJ mode, and OFF (no display) in the NORMAL mode.

51. DELETE button ☞ P.46

Press to delete cue points and loop points recorded in memory card.

52. MEMORY button ☞ P.43

Press to store cue points or loop points in memory card.

53. MENU button

Press to display DVD menu. Also, during MP3 playback, displays MP3 navigator screen. (☞ P.42)

54. Top menu (T.MENU) button

Press to display a DVD’s top menu level.

55. SETUP button ☞ P.17

Press to display the setup menu.

56. RETURN button

When setup or other menus are displayed, press this button to return to the previous menu or item.

English

<DRB1414> En

Before Operating (Names and Functions of Parts)

Display

123

456 7 8

1. Title/Folder number display (TITLE/FLD 00 to 99)

Indicates the DVD title number. During MP3 playback, displays folder number. Not displayed during CD playback.

2. Chapter number (CHP 000 to 999)

Indicates the DVD chapter number. During CD/MP3 playback, “CHP” does not appear.

3. Track number (TRACK 00 to 99/000 to 999 (MP3))

Indicates CD or MP3 track number.

“TRACK” is not displayed during DVD playback.

4. Total track number (ALL)

When playing DVD, displays the total number of chapters within the title. When playing an audio CD, displays the total number of tracks on the disc. When playing MP3, displays the total number of tracks within the folder.

5. Auto cue (A.CUE) indicator

Lights when auto cue is ON. Does not light during NORMAL mode.

6. Remaining time (REMAIN) indicator

Indicates that the current numerical display is of a track’s remaining time.

7. Minutes display (000 to 999 M)

8. Seconds display (00 to 59 S)

9. Frame display (00 to 74 F)

Display audio frame numbers. 75 frames are equivalent to one second of normal play. Not displayed in NORMAL mode.

10. Video frame display (00 to 29 VIDEO F)

Lights during DVD playback in DJ mode. 30 frames are equivalent to one second. Video frame display does not appear during CD playback and in NORMAL mode. Since this unit controls video frames (1/30 second) based on the audio frame (1/75 second), combining the two will result in a maximum deviation of 1.

11. TEMPO indicator

Displays tempo variation produced when TEMPO control slider is operated. Does not light in NORMAL mode.

12. Tempo control range display (±6, ±10, ±16, WIDE)

Lights to indicate the TEMPO control slider’s variable range as se- lected with the tempo control range select button. Does not light in NORMAL mode.

13. BPM counter display

Lights to indicate the beats per minute (BPM) of the currently playing track. Some tracks may not be measurable with the automatic BPM counter. Does not light in NORMAL mode.

14. Master tempo indicator (MT)

Lights when master tempo function is ON. Does not light in NORMAL mode.

15. Dot matrix display (100x7 dots)

Used for displaying various items, including TEXT, WAVE, guide, etc. During CD TEXT display, shows up to 72 characters for disc title or up to 48 characters for track title; for MP3, displays up to 48 characters (display scrolls when 15 or more characters are to be shown). In the case of WAVE display, the varying volume levels of the currently playing track are displayed, with the track sized to fit into the entire 100-dot display width. For guide messages, see P.50 “Dot Matrix Guide Display Mes-

sages”.

9 10 11

16 151923 18202122

141213

16. Play address display

Displays a bar graph to allow an immediate visual grasp of the elapsed and remaining playing time of the currently playing track. The full scale bar length indicates the full track length. ¶ The bar graph is off at the beginning of the track, and lights from

left to right.

¶ The bar graph is lighted at the beginning of the track, and goes out

from left to right.

¶ When the remaining playing time falls below 30 seconds, the bar

graph flashes slowly; when less than 15 seconds are left, the bar graph flashes quickly.

17. Prohibited indicator ( )

Some DVD discs or players do not support certain functions or operations; if an effort is made to perform such operations, this indicator appears for about 2 seconds.

18. CUE point indicator

When a point is recorded in the CUE button or IN/REALTIME CUE/ IN ADJUST button for the currently selected track, the “CUE” indi-

cator lights and the point’s relative starting position is shown in the display (2 lighted dots). Does not light in NORMAL mode.

19. MEMORY display

If the currently selected track includes cue memory or loop memory, the “MEMORY” indicator lights and the MEMORY display indicates the relative starting position of the cue or loop. Two dots are used to display 1 point, and even if multiple starting positions are included within a single point, only one point is displayed. Does not light in NORMAL mode.

20. SRS indicator ( )

Lights when TruSurround function is selected. This function is disabled in DJ mode.

21. Dolby Digital indicator (2 D)

Lights during playback when Dolby Digital audio has been selected.

22. DTS indicator

Lights during playback when DTS audio has been selected. Not supported in DJ mode.

23. Video out indicators (VIDEO OUT/PAL/NTSC)

When the video output TV system is set to AUTO, only the “VIDEO OUT” indicator lights.

When NTSC has been selected, both the “VIDEO OUT” and “NTSC” indicators light. When PAL has been selected, both the “VIDEO OUT” and “PAL” indicators light.

24. Angle indicator ( )

During DVD playback, this mark appears to indicate a scene with variable angle.

En <DRB1414>

Jog dial display

Before Operating (Names and Functions of Parts)Before Operating (Names and Functions of Parts)

1. Operation display

Displays play position, with one revolution equivalent to 135 frames. The display rotates during playback, and stops during pause.

2. Cue point position display

Displays the position of cue points.

3. Audio/video memory status display

Flashes during writing to the audio/video memory. While indicator is flashing, it may not be possible to record real time cue points or hot cue points.

4. Jog touch detector indicator

When VINYL mode is set to ON, this indicator lights when the top panel of the jog dial is touched.

5. VINYL mode indicator (Vinyl)

Lights when VINYL mode is set to ON.

Rear panel

DIGITAL

AUDIO OUT

R L

OUT

PREVIEW OUT

CONTROL

VIDEO OUT

NORMAL

COMPOSITE

SYNC IN

POWER

125

OFF ON

AC IN

2 3

English

678 9

1. POWER OFF (—)/ON (_) switch

2. NORMAL/DJ switch (☞ P.14)

If this switch position is changed during playback, playback will stop, and then resume playback from the disc’s begin- ning. DJ: For jog dial, tempo variation and other DJ operations. During DVD playback, subtitles and some other functions, operations, or playback points may not be supported. NORMAL: DJ functions are not supported. Pause mode is silent, not audible. During DVD playback, selected audio signals are output from the digital output connectors. During CD playback, digital data containing subcodes are output (does not support CD graphics).

3. CONTROL connector

Using the supplied accessory control cord, this connector can be connected to a Pioneer DJ mixer (sold separately) to allow control of this unit from the DJ mixer. This facilitates the use of functions such as fader start play and back cue. Alternately, linking this connector to another DJ player allows automatic relay play (☞ P.41).

4. AUDIO OUT L/R connectors

RCA type analog audio output connectors.

5. Main video output connectors (VIDEO OUT)

Includes RCA and BNC type connectors for outputting DVD playback video only (composite signals), as well as S-Video output connector.

6. DIGITAL OUT connector

RCA type coaxial digital output, for connecting AV amplifier, Dolby Digital/DTS decoder, CD recorder, etc. When NORMAL/DJ switch is set to “DJ”, during DVD play- back the unit outputs 2-channel linear PCM digital data, regardless of the selected audio signal format. During CD playback, the unit outputs only audio data that do not include subcodes. When NORMAL/DJ switch is set to “NORMAL”, during DVD playback the unit outputs digital data in the audio signal format selected. During CD playback, the unit outputs digital data including subcodes.

7. Preview video output connectors (PREVIEW OUT)

RCA type connector (composite signals) and S-Video output connector. These connectors output monitor images used to aid the DJ during operation. Outputs various guide messages and displays (☞ P.12).

8. SYNC IN connector

BNC type input connector for inputting external sync signal. Use to connect optional dedicated sync signal generator.

9. AC inlet (AC IN)

Use auxiliary power cord to connect to standard electrical outlet.

<DRB1414> En

Before Operating (Names and Functions of Parts)

Main video output (VIDEO OUT) and preview video output (PREVIEW OUT)

★ The example shown here is an illustration meant to depict the general display contents, and may differ somewhat from actual monitor

appearance.

This unit is equipped with both main video output (VIDEO OUT) and preview video output (PREVIEW OUT) connectors. In NORMAL mode, both VIDEO OUT and PREVIEW OUT produce the same video signals. In DJ mode, the outputs of the two connectors are different, as indicated below. Even in DJ mode, however, if a non-supported DJ operation is attempted, the outputs will be the same as in NORMAL mode.

■ VIDEO OUT

This outputs only the DVD playback image; it should be connected to the main publicly viewed monitor.

■ PREVIEW OUT

This outputs the images used by the DJ when operating the unit, and includes various additional guide messages and menus.

VIDEO OUT PREVIEW OUT

Guide display area

Title number, chapter number

Angle indicator

Play

1–010

REV

In reverse mode displays “REV” indicator

Status indicator

Play: Normal playback Loop: Loop playback Cue: Cue standby Pause: Normal pause (standby) Scratch: Scratch operation Search: Chapter/track search

¡: Forward search (scan) 1: Reverse search (scan)

Reading: Recall hot cue, or cue point

3. 45. 67/

CBA

Area for onscreen display of thumbnail images of points recorded in HOT CUE and CUE buttons.

Chapter contents are displayed as minutes, seconds, and frames. When time mode is set to REMAIN, displayed numbers are preceded with a “minus” (–) symbol, for example, “–1.10.08”.

4. 56

WAVE Display: Displays relative music levels of entire track spread over full scale length.

Playing address display: The current relative point in track playback is displayed as a bar graph, with entire track length spread over full scale length, thus allowing immediate visual grasp of the current playback position in the track.

Total time in chapter (minutes / seconds)

“Prohibited” mark and other indicators

CUE

PREVIEW OUT (for MP3)

En <DRB1414>

PREVIEW OUT (for CD)

Before Operating (Connections)Before Operating (Connections)

Connections

Before making or changing the connections, switch off the power and disconnect the power cord from the AC outlet.

1. Connections to a Pioneer DJ mixer (sold separately) (audio output and control connector)

Using the accessory audio cable, connect the white plug to the L (left) connector, and connect the red plug to the R (right) connector. By connecting the accessory control cord, the player can be controlled from the mixer, allowing fader start play and back cue operations. Note that digital connections can be made only with mixers equipped with digital input connectors (models DJM-800, DJM-1000, etc.). Use a commercially available coaxial digital cable to connect this unit’s DIGITAL OUT connector to the DJ mixer’s DIGITAL IN connector.

English

Connection example DJM-800:

SIGNAL GND

PHONO

CONTROL

DIGITAL

DVJ-1000

DIGITAL

AUDIO OUT

R L

OUT

PREVIEW OUT

CONTROL

VIDEO OUT

NORMAL

COMPOSITE

SYNC IN

LINE

DJM-800

CONTROL

DIGITAL

DIGITAL IN

Coaxial digital cable (sold separately)

Accessory control cord

Accessory

DIGITAL

DVJ-1000

AUDIO OUT

R L

OUT

PREVIEW OUT

CONTROL

VIDEO OUT

NORMAL

COMPOSITE

SYNC IN

audio cable

¶ When making connections to the DJM-1000, the furnished audio cables can be used to connect one set of the CD/LINE connectors

to player A, and the other set of CD/LINE connectors to a second player B. When making digital audio connections, a commercially available coaxial digital signal cable must be used to connect this unit’s DIGITAL OUT connector to one of the DIGITAL IN connectors (3 to 6) of the DJM-1000 mixer.

¶ When connecting to the DJM-600, DJM-500, or DJM-300, use the furnished audio cables to connect the CD1 connectors to player

A, and CD2 connectors to player B.

¶ When connecting to DJM-909, DJM-707 or DJM-400 use the furnished audio cables to connect the CH-1 CD connectors to player

A, and CH-2 CD connectors to player B.

¶ When connecting to DJM-3000, connect player A to CH-1 LINE 1, and player B to CH-2 LINE 3. ¶ When connecting this unit to other audio mixers, connect the unit’s AUDIO OUT connectors to the mixer’s LINE IN or AUX IN

connectors. (★ DO NOT connect to the PHONO connectors, since it may result in distorted sound or improper playback.)

<DRB1414> En

Before Operating (Connections)

2. Control cord connection for relay play

By using the accessory control cord to connect two DJ players, automatic relay play can be performed between the two units. (☞ P.41)

DVJ-1000

AUDIO OUT

NORMAL

R L

CONTROL

COMPOSITE

VIDEO OUT

DIGITAL

OUT

SYNC IN

PREVIEW OUT

OFF ON

POWER

AC IN

Accessory control cord

DIGITAL

OUT

PREVIEW OUT

3. Connection to stereo amplifier (without DJ mixer)

Connect CD or AUX input connector (do not connect to PHONO input connector)

Stereo amplifier

Accessory audio cable

DVJ-1000

DIGITAL

OUT

DVJ-1000

AUDIO OUT

NORMAL

R L

CONTROL

COMPOSITE

VIDEO OUT

SYNC IN

AUDIO OUT

R L

CONTROL

VIDEO OUT

PREVIEW OUT

NORMAL

COMPOSITE

SYNC IN

OFF ON

POWER

AC IN

4. Connection to component equipped with digital input connector

CD recorder or amplifier with digital input connector, etc.

Coaxial digital cable (sold separately)

■ Setting the NORMAL/DJ switch (rear panel)

When the unit is used normally as a DJ DVD player, the mode select switch should be set to the “DJ” position. If the switch position is changed during playback, playback will stop and after the stop, playback will begin from the beginning of the disc.

When set to DJ (DJ mode):

¶ During DVD playback, the digital output connectors produce 2-channel linear PCM digital data, regardless of the selected audio

signal format. In addition, subtitles and certain other functions and operations are not supported.

¶ During CD playback, the digital connector outputs only audio data without sub-codes. However, sampling frequency is fixed at 44.1

kHz. As a result, limitations of recording or other functions may be experienced when certain CD recorders or other components are connected. For details, consult the Operating Instructions for the component to be connected.

¶ Some functions may be limited or disabled during DVD playback (☞ P.3, “About DVD playback in DJ mode”).

DVJ-1000

DIGITAL

AUDIO OUT

R L

OUT

PREVIEW OUT

CONTROL

VIDEO OUT

NORMAL

COMPOSITE

SYNC IN

When set to NORMAL (NORMAL mode):

¶ The digital connector outputs digital data including sub-codes, but the player’s DJ functions are disabled. ¶ When unsupported operations are attempted the message “NORMAL” will appear in the display. ¶ When power is turned ON, if the NORMAL/DJ switch is set to “NORMAL”, the display shows the message “NORMAL”. ¶ If you wish to use all ordinary functions during DVD playback, set the unit to NORMAL mode (☞ P.3, “About DVD playback in DJ

mode”).

En <DRB1414>

Before Operating (Connections)Before Operating (Connections)

Note:

Most DJ functions (cue, loop, reloop, tempo adjust, hot cue, jog dial, reverse play) are not supported when the NORMAL/DJ switch is set to “NORMAL”. In addition, the pause mode is silent, not audible.

5. Connection to television monitor (composite video/S-Video)

This player is equipped with two video output connectors: a main video output connector (VIDEO OUT) which outputs only the DVD playback image, and a preview video output connector (PREVIEW OUT) which produces a variety of data displays used by the DJ during a performance.

¶ Each of the television monitors is connected by using standard video cables (RCA plug) or S-Video cables. ¶ The main video output is also equipped with a BNC type output connector (COMPOSITE), allowing the use of a BNC connector

cable if desired.

* Only one video cable is provided as an accessory. S-Video cables and BNC connector cables are not provided.

English

Main monitor

S-VIDEO

INPUT

VIDEO INPUT

Video cable

S-Video cable

BNC connector cable

DIGITAL

OUT

AUDIO OUT

R L

PREVIEW OUT

CONTROL

VIDEO OUT

DVJ-1000

NORMAL

COMPOSITE

SYNC IN

Video cable

S-Video cable

Preview monitor

VIDEO INPUT

S-VIDEO

INPUT

★ Connect the player’s video output directly to a television monitor, not to a video deck (if connected through a video deck,

the copy guard function may prevent proper playback).

<DRB1414> En

Before Operating (Connections)

6. Connection to video mixer

Use a standard video cable (RCA plug) or S-Video cable for these connections.

Main monitor

Preview monitor

S-VIDEO

VIDEO

INPUT

S-Video cable

S-VIDEO

Video mixer

VIDEO INPUT

INPUT

S-Video cable

Video cable

DVJ-1000 B

Video cable

S-Video cable

VIDEO OUTPUT

VIDEO INPUT 2

S-Video cable

VIDEO INPUT 1

Preview monitor

Video cable

DVJ-1000 A

VIDEO INPUT

S-VIDEO

INPUT

Video cable

DIGITAL

AUDIO OUT

R L

OUT

PREVIEW OUT

CONTROL

VIDEO OUT

NORMAL

COMPOSITE

SYNC IN

DIGITAL

AUDIO OUT

R L

OUT

PREVIEW OUT

CONTROL

VIDEO OUT

NORMAL

COMPOSITE

SYNC IN

S-Video cable

7. Connecting the power cord

After all other connections are completed, connect one end of the accessory power cord to the rear-panel AC inlet, and connect the other end (power plug) to a wall outlet.

En <DRB1414>

Preparations (Setup)Preparations (Setup)

ENTER

MENU T.MENU

RETURN

SETUP

TOUCH/BRAK

Setup

Initial setup is required before playing DVDs.

TV system setting for video output

This setting is used to switch the TV system used for video output. Confirm on the following table the TV system format in which each kind of disc will be output.

Player setting Disc type DVD (NTSC) DVD (PAL) CD or no disc

1. Set the player’s POWER switch to OFF.

2. While depressing the DVD TITLE \ button, set the power to ON.

3. Release the DVD TITLE \ button once the TV system is shown in the display.

Each time steps 1 to 3 are repeated, the setting alternates as follows: PAL (factory default) = AUTO AUTO = NTSC NTSC = PAL ¶ Note that visual quality may deteriorate if the disc’s record-

ing method differs from the TV system selected for output.

AUTO mode

NTSC PAL NTSC or PAL

NTSC mode

NTSC NTSC NTSC

PAL mode

PAL PAL PAL

Using the Setup Navigator

The “Setup Navigator” uses a dialog format to make basic television and amplifier settings. The various settings are made automatically as the user responds to displayed questions. The Setup Navigator function cannot be used during playback. When Setup Navigator is started, setup questions appear in the following order: Language (OSD Language) \ TV Connection (TV type) \ Amp Connection

1. Set POWER switch to ON.

If a disc is already loaded, remove it.

2. Press SETUP button.

The Setup Navigator screen will appear.

Audio1

Setup Navigator

Setup using the Setup Navigator

Start:

Select to begin the Setup Navigator.

Auto Start Off:

Select if Setup Navigator settings are already completed.

¶ When [Auto Start Off] is selected, the next time the SETUP

button is pressed the manual Setup Menu will appear.

Video1

Language

Setup Navigator

Move

ENTER

General

Start

Auto Start Off

SETUP

Select

Exit

English

How to perform setup

Setup operations are performed by first pressing the SETUP button to display the Setup Menu on the screen; the cursor button is used to select items, and items are confirmed with the ENTER button. The cursor button contains four sensors ( button. Press the top (

), bottom ( ), left ( ) and right ( ) sides of the button to move in the corresponding directions on the screen.

Settings are performed via a “Setup Navigator” which uses a dialog format to make basic settings of television and amplifier; a “Setup Menu Mode” is used for individual settings. First press the SETUP button to start the “Setup Navigator”. “Setup Menu Mode” includes “Basic” and “Expert”; the latter mode allows more detailed settings.

OFF ON

POWER

TIME

AUTO

MODE

CUE

TEXT MODE

DVD TITLE MP3 FOLDER

HOT CUE

DIRECTION

FWD

REC MODE

ANGLE SUBTITLE AUDIO

REALTIME CUE

BACK & FORTH

OUT

OUT ADJUSTIN ADJUST

DISPLAY

DELETE

RELOOP/

4-BEAT

EXIT

ONE-TRACK

LOOP

/ / / ) in a single

DVJ-1000

UNLOCK

MEMORY MENU T.MENU

CUE / LOOP

CALL

JOG ADJUST

RETURN

TOUCH/BRAKE

ENTER

RELEASE/START

LIGHT

HEAVY

HYPERJOG MODE

JOG MODE

VINYL

WIDE

STOP

LOCK

EJECT

SETUP

3. Press ENTER button.

The Setup Navigator is initiated.

■ During setup, to return to the previous menu screen:

Press the cursor button’s left side ( ).

Select On-Screen-Display (OSD) Language

Languages selectable include English, French, German, Italian, or Spanish.

Press the cursor button’s up/down sides ( / ) to move the cursor to the language desired, then press ENTER button to confirm.

Audio1

Setup Navigator

Language

Select the On Screen Language

English: OSD Language is English. Français: OSD Language is French. Deutsch: OSD Language is German. Italiano: OSD Language is Italian. Español: OSD Language is Spanish.

¶ The language selected as the OSD Language is automatically

selected as the language used in subtitles and audio. (☞ P. 26)

Video1

Language

OSD Language

Move

ENTER

English

français Deutsch Italiano Español

Select

General

SETUP

Exit

<DRB1414> En

Preparations (Setup)

Select type of television connected

Sets the type of television connected to the player.

Press the cursor button’s up/down sides ( / ) to move the cursor to the item desired, then press ENTER button to confirm.

Audio1

Setup Navigator

TV Connection

Widescreen TV 16:9 aspect ratio

Widescreen(16:9):

Select this option when connecting a television with Widescreen (16:9) aspect ratio.

Standard(4:3):

Select this option when connecting a television with conventional (4:3) aspect ratio.

Video1

TV Type

Move

Language

Widescreen(16:9)

Standard(4:3)

ENTER

General

Select

SETUP

Exit

Select the type of digital signal supported by your amplifier

★ Digital output during DJ mode is automatically converted

to linear PCM only.

Set the type of digital signal supported by the amplifier connected to the player. (Consult the Operating Instructions for your amplifier when making this setting.)

Press the cursor button’s up/down sides ( / ) to move the cursor to the item desired, then press ENTER button to confirm.

Audio1

Setup Navigator

Amp Connection

Compatible with Dolby Digital

Dolby Digital:

Select this item if you have used a digital audio cable to connect a AV amplifier to the player, and the amplifier supports the Dolby Digital format.

Dolby Digital/DTS:

Select this item if you have used a digital audio cable to connect an AV amplifier to the player, and the amplifier supports Dolby Digital and DTS formats.

Dolby Digital/MPEG:

Select this item if you have used a digital audio cable to connect an AV amplifier to the player, and the amplifier supports Dolby Digital and MPEG formats.

Dolby D/DTS/MPEG:

Select this item if you have used a digital audio cable to connect an AV amplifier to the player, and the amplifier supports Dolby Digital, DTS, and MPEG formats.

PCM:

Select this item if you have used a digital audio cable to connect a stereo or Dolby Pro Logic amplifier.

Not Connected:

Select this item if you have used the accessory analog audio cable to connected an amplifier, or if you do not know whether the amplifier supports digital signals. When this item is selected, the next setting [96kHz PCM Audio] is not required; skip it and go directly to [Exit Setup Navigator].

¶ If your amplifier does not support DTS audio, do not select

the [Dolby Digital/DTS] or [Dolby D/DTS/MPEG], since additional noise may occur.

En <DRB1414>

Video1

Digital Jack

Move

Language

General

Dolby Digital

Dolby Digital/DTS Dolby Digital/MPEG Dolby D/DTS/MPEG PCM Not Connected

Select

SETUP

ENTER

Exit

Select whether connected amplifier supports 96 kHz audio

Set this item to reflect whether the connected amplifier supports linear PCM 96 kHz audio.

Press the cursor button’s up/down sides ( / ) to move the cursor to the item desired, then press ENTER button to confirm.

Audio1

Setup Navigator

Amp Connection

96kHz PCM Audio

Digital jack not compatible with 96kHz

No:

Connected amplifier does not support linear PCM 96 kHz audio.

Yes:

Connected amplifier does support linear PCM 96 kHz audio.

Don’t Know:

Select this item if you are unsure whether the connected amplifier supports linear PCM 96 kHz audio. ¶ If [No] or [Don’t Know] is selected, DVD audio will be con-

verted to 48 kHz for output, regardless of whether it is originally linear PCM 96 kHz.

Video1

Move

Language

ENTER

General

Yes Don't Know

Select

SETUP

Exit

Exit Setup Navigator

Choices here include: to save the new settings and close Setup Navigator; to abandon (delete) the new settings and close Setup Navigator, or to start over without closing.

Press the cursor button’s up/down sides ( / ) to move the cursor to the item desired, then press ENTER button to confirm.

Audio1

Setup Navigator

Exit Setup Navigator

Changes are saved

Save Changes:

The new settings will be saved and applied, and Setup Navigator will close.

Delete Changes:

New settings will be abandoned and Setup Navigator will close.

Start Again:

Setup Navigator will return to the [OSD Language] and start settings again.

¶ If [Save Changes] or [Delete Changes] is chosen, the initial

setup menu will close.

¶ If [Start Again] is selected, the display will return to the [OSD

Language] menu screen.

Video1

Move

Language

Save Changes

Delete Changes Start Again

ENTER

General

Select

SETUP

Exit

Setup Menu items

Preparations (Setup)Preparations (Setup)

Manual setup using the Setup Menu allows a greater variety of setup options than the Setup Navigator. Consult the pages Noted for more information about the contents of items and options listed on the menu.

¶ ❚ indicates factory default values. ¶

[Expert] mode.

Audio1

Audio DRC Off On Dolby Digital Out Dolby Digital Dolby Digital PCM DTS Out Off DTS 96kHz PCM Out 96kHz 48kHz 96kHz MPEG Out MPEG MPEG PCM Digital Out On Off

Audio2

Virtual Surround Off TruSurround Legato PRO Off Standard Effect1 Effect2 Effect3 Hi-Bit On Off

Audio1

TV Screen 4 : 3(Letter Box) 4 : 3(Pan&Scan) 16 : 9(Wide) S-Video Out S1 S2 Screen Saver On Off

settings are displayed in the Setup Menu’s

Video1

V2Video1

Language

General

P.21

P.22

P.23

P.24

Video2

Video1

Audio1

Background Pioneer Logo Black Video Adjust Start

Still Picture Field Frame Auto On Screen Display On Off Angle Indicator On Off

Audio1

OSD Language English français Deutsch Italiano Español Audio Language English French German Italian Spanish Other Subtitle Language English French German Italian Spanish Other Auto Language On Off DVD Language w / Subtitle Language English French German Italian Spanish Other Subtitle Display On Off Assist Subtitle Subtitle Off With Audio Selected Subtitle

Language

General

P.25

P.24

P.25

P.26

P.27

P.28

English

Audio1

Setup Menu Mode Expert Basic Setup Navigator Start

Parental Lock Password (Change) Level Country Code

Video1

Language

General

P.21

P.17

P.29

<DRB1414> En

Preparations (Setup)

To return all settings to their factory defaults

Use this command to return all changed settings to their factory default values.

1. Turn power OFF.

2. While holding the STOP button depressed, set

the POWER switch to ON, and continue holding the STOP button until the “POWER ON” indication goes off.

¶ All setting contents will be returned to their factory default

values. The DJ mode functions listed below are set to the following factory defaults in addition to the items in the Setup Menu (P.19). Auto Cue: OFF Auto Cue level: –60 dB Jog mode: VINYL ON Time mode: REMAIN TV system setting for video output: PAL

■ This command additionally erases all memory contents, in-

cluding “video memory” (☞ P.24). Be sure you wish to delete all memory contents before using this command.

Using the Setup Menu

★ Setup menu functions are disabled during DVD playback

in DJ mode, and during CD playback. Set the unit to stop, or remove the disc before attempting setup operations.

The Setup Menu is used when you wish to modify the default factory settings. The following instructions introduce the basic operations and controls used with the Setup Menu. ¶ If you have not yet performed the basic setup using the Setup

Navigator, the Setup Navigator screen will appear first.

Confirm that power is turned ON, then

1. Press the SETUP button.

The Setup Menu will appear.

[Example]