Pioneer DEH-X5600BT, DEH-X6600BS, DEH-X3600S, DEH-X3600UI Service manual

PIONEER CORPORATION 1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa 212-0031, Japan

PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936

PIONEER CORPORATION 2013

CD RDS RECEIVER

ORDER NO.

CRT5373

DEH-X5600BT/XNEW5

DEH-X5600BT

DEH-X6600BS/XNUC
DEH-X3600S/XNUC
DEH-X3600UI/XNEW5

This service manual should be used together with the following manual(s):

Model No. Order No. Mech. Module Remarks

CX-3287

CRT4759 S11.6STD CD Mech. Module : Circuit Descriptions, Mech. Descriptions, Disassembly

/XNEW5

K-ZZZ JULY 2013 Printed in Japan

1234

1234

C

D

F

A

B

E

SAFETY INFORMATION

CAUTION

Where in a manufacturer’s service documentation, for example in circuit diagrams or lists
of components, a symbol is used to indicate that a specific component shall be replaced only
by the component specified in that documentation for safety reasons, the following symbol shall
be used:

This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer.
Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair
complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty.
If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so
and refer the repair to a qualified service technician.

CAUTION:

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE
SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

- Safety Precautions for those who Service this Unit.
When checking or adjusting the emitting power of the laser diode exercise caution in order to get safe, reliable
results.

Caution:

1. During repair or tests, minimum distance of 13 cm from the focus lens must be kept.

2. During repair or tests, do not view laser beam for 10 seconds or longer.

WARNING

This product may contain a chemical known to the State of California to cause cancer, or birth defects or
other reproductive harm.
Health & Safety Code Section 25249.6 - Proposition 65

WARNING!

The AEL (accessible emission level )of the laser power output is less than CLASS 1
but the laser component is capable of emitting radiation exceeding the limit for
CLASS 1.
A specially instructed person should do servicing operation of the apparatus.

CAUTION

This product is a class 1 laser product classi­fied under the Safety of laser products, IEC
60825-1:2007.

Laser diode characteristics

Wave length : 785 nm to 814 nm

Maximum output : 1 190 µW(Emitting period : unlimited)

Additional Laser Caution

Transistors Q101 in PCB drive the laser diodes.
When Q101 is shorted between their terminals, the laser diodes will radiate beam.
If the top cover is removed with no disc loaded while such short-circuit is continued,
the naked eyes may be exposed to the laser beam.

2

DEH-X5600BT/XNEW5

5 678

56

7

8

C

D

F

A

B

E

CAUTION

Danger of explosion if battery is incorrectly replaced.
Replaced only with the same or equivalent type recommended by the manufacturer.
Discord used batteries according to the manufacturer's instructions.

DEH-X5600BT/XNEW5

3

1234

1234

C

D

F

A

B

E

CONTENTS

SAFETY INFORMATION..................................................................................................................................... 2

1. SERVICE PRECAUTIONS............................................................................................................................... 5

1.1 SERVICE PRECAUTIONS ........................................................................................................................ 5

1.2 NOTES ON SOLDERING .......................................................................................................................... 5

2. SPECIFICATIONS............................................................................................................................................ 6

2.1 SPECIFICATIONS ..................................................................................................................................... 6

2.2 DISC/CONTENT FORMAT ........................................................................................................................ 8

3. BASIC ITEMS FOR SERVICE.......................................................................................................................... 9

3.1 CHECK POINTS AFTER SERVICING....................................................................................................... 9

3.2 PCB LOCATIONS ...................................................................................................................................... 9

3.3 JIGS LIST ................................................................................................................................................ 10

3.4 CLEANING............................................................................................................................................... 10

4. BLOCK DIAGRAM.......................................................................................................................................... 12

5. DIAGNOSIS.................................................................................................................................................... 14

5.1 OPERATIONAL FLOWCHART................................................................................................................ 14

5.2 ERROR CODE LIST ................................................................................................................................ 15

5.3 CONNECTOR FUNCTION DESCRIPTION............................................................................................. 19

6. SERVICE MODE ............................................................................................................................................ 20

6.1 DISPLAY TEST MODE 1 ......................................................................................................................... 20

6.2 DISPLAY TEST MODE 2 ......................................................................................................................... 21

6.3 SOFTWARE VERSION UP METHOD..................................................................................................... 22

6.4 CD TEST MODE...................................................................................................................................... 23

7. DISASSEMBLY .............................................................................................................................................. 24

8. EACH SETTING AND ADJUSTMENT ........................................................................................................... 30

8.1 CD ADJUSTMENT................................................................................................................................... 30

8.2 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT.................................................... 31

8.3 PCL OUTPUT CONFIRMATION.............................................................................................................. 33

9. EXPLODED VIEWS AND PARTS LIST.......................................................................................................... 33

9.1 PACKING ................................................................................................................................................. 34

9.2 EXTERIOR............................................................................................................................................... 38

9.3 CD MECHANISM MODULE..................................................................................................................... 40

10. SCHEMATIC DIAGRAM............................................................................................................................... 42

10.1 TUNER AMP UNIT (GUIDE PAGE) ....................................................................................................... 42

10.2 KEYBOARD UNIT.................................................................................................................................. 48

10.3 CD CORE UNIT (S11.6VA) .................................................................................................................... 50

10.4 BT UNIT ................................................................................................................................................. 52

10.5 WAVEFORMS ........................................................................................................................................ 54

11. PCB CONNECTION DIAGRAM.................................................................................................................... 56

11.1 TUNER AMP UNIT................................................................................................................................. 56

11.2 KEYBOARD UNIT .................................................................................................................................. 60

11.3 CD CORE UNIT (S11.6VA) .................................................................................................................... 62

11.4 BT UNIT ................................................................................................................................................. 64

12. ELECTRICAL PARTS LIST .......................................................................................................................... 65

4

DEH-X5600BT/XNEW5

5 678

56

7

8

C

D

F

A

B

E

1. You should conform to the regulations governing the product (safety, radio and noise, and other
regulations), and should keep the safety during servicing by following the safety instructions
described in this manual.

2. Before disassembling the unit, be sure to turn off the power. Unplugging and plugging the connectors
during power-on mode may damage the ICs inside the unit.

3. To protect the pickup unit from electrostatic discharge during servicing, take an appropriate treatment
(shorting-solder) by referring to "the DISASSEMBLY".

4. After replacing the pickup unit, be sure to check the grating.

5. Be careful in handling ICs. Some ICs such as MOS type are so fragile that they can be damaged by
electrostatic induction.

6. Notes about installation and pin number description of Power IC (IC301: PA2032A)
The Power IC, PA2032A used on tha Tuner Amp Unit is a 25 pin IC.
The same PCB of the Tuner Amp Unit is used for other models that use a 27 pin IC, too.
So, the PCB has lands for a 27 pin IC.
When you replace the Power IC, install the Power IC onto 25 pins (2- 26 pin) located in the center of 27 pins for IC301.

Therefore, when you check the Power IC on the block diagram, the schematic diagram and the PCB connection
diagram, you have to pay attention as follows.

BLOCK DIAGRAM SCHEMATIC DIAGRAM

The pin number of left side is a number
on the PCB (silk printing).

The pin number of right side (in the IC frame)
means the pin number of IC itself.

The pin number is a number on the PCB
(silk printing).
The number in parentheses means the
pin number of IC itself.

10 (9)

8 (7)

6 (5)

4 (3)

26 (25)

H-SW

12 (11)

13 (12)

23 (22)

2 (1)

OFF.DET

No connection

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25

No connection

For environmental protection, lead-free solder is used on the printed circuit boards mounted in this unit.
Be sure to use lead-free solder and a soldering iron that can meet specifications for use with lead-free solders for repairs
accompanied by reworking of soldering.

Compared with conventional eutectic solders, lead-free solders have higher melting points, by approximately 40 C.
Therefore, for lead-free soldering, the tip temperature of a soldering iron must be set to around 373 C in general, although
the temperature depends on the heat capacity of the PC board on which reworking is required and the weight of the tip of
the soldering iron.

Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting
temperatures (hard to melt/easy to harden).

The following lead-free solders are available as service parts:
Parts numbers of lead-free solder:
GYP1006 1.0 in dia.
GYP1007 0.6 in dia.
GYP1008 0.3 in dia.

1. SERVICE PRECAUTIONS

1.1 SERVICE PRECAUTIONS

1.2 NOTES ON SOLDERING

DEH-X5600BT/XNEW5

5

1234

1234

C

D

F

A

B

E

2. SPECIFICATIONS

DEH-X5600BT/XNEW5

General

Power source.............................14.4 V DC (10.8 V to 15.1 V

allowable)

Grounding system...................Negative type

Maximum current consumption

....................................................10.0 A

Dimensions (W × H × D):
DIN

Chassis.........................................178 mm × 50 mm ×

165 mm

Nose...............................................1 88 mm × 58 mm × 15 mm

(DEH-X5600BT)

Nose...............................................1 88 mm × 58 mm × 16 mm

D

Chassis.........................................178 mm × 50 mm ×

165 mm

Nose...............................................170 mm × 46 mm × 15 mm

Weight .......................................... 1 kg

Audio

Maximum power output ....... 50 W × 4

70 W × 1/2 Ω (for subwoo­fer)

Continuous power output ...22 W × 4 (50 Hz to

15 000 Hz, 5% THD,
4 Ω load, both channels dri-

ven)

Load impedance ......................4 Ω (4 Ω to 8 Ω allowable)

Preout maximum output level

................................................... 2. 0 V

Loudness contour ...................+10 dB (100Hz), +6.5 dB

(10 kHz) (volume: –30 dB)
Equalizer (5-Band Graphic Equalizer):

Frequency....................................80 Hz/250 Hz/800 Hz/

2.5 kHz/8 kHz

Equalization range..................±12 dB (2 dB step)

Subwoofer (mono):

Frequency....................................50 Hz/63 Hz/80 Hz/100 Hz/

125 Hz/160 Hz/200Hz

Slope..............................................–12 dB/oct, –24 dB/oct

Gain ................................................+ 6 dB t o –24 dB

Phase ............................................Normal/Reverse

CD player

System ..........................................Compact disc audio system

Usable discs ..............................Compact disc

Signal-to-noise ratio...............94 dB ( 1 kHz) (IEC-A net-

work)

Number of channels ..............2 (s tereo)

MP3 decoding format ........... MPE G-1 & 2 Audio Layer 3

WMA decoding format .........Ve r. 7, 7.1, 8, 9, 10, 11, 12

(2 ch audio)
(Windows Media Player)

WAV signal format..................Linear PCM & MS ADPCM

(Non-compressed)

USB

USB standard specification

.....................................................USB 2.0 full speed

Maximum current supply .... 1A

USB Class...................................MSC (Mass Storage Class)

Fi le s yst em..................................FAT12, FAT16, FAT32

MP3 decoding format ........... MPEG-1 & 2 Audio Layer 3

WMA decoding format ......... Ve r. 7, 7.1, 8, 9, 10, 11, 12

(2 ch audio)
(Windows Media Player)

WAV signal format..................Linear PCM & MS ADPCM

(Non-compressed)

FM tuner

Frequency range......................87.5 MHz to 108.0 MHz

Us able sensi ti vit y.....................9 dB f (0.8 µV/75 Ω, mono,

S/N: 30 dB)

Signal-to-noise ratio...............72 dB (IEC -A network)

MW tuner

Frequency range...................... 531 k Hz to 1 602 k Hz

Us able sensi ti vit y.....................2 5 µV (S/N: 20 dB)

Signal-to-noise ratio...............62 dB (IEC -A network)

LW tuner

Frequency range...................... 153 k Hz to 28 1 kHz

Us able sensi ti vit y.....................2 8 µV (S/N: 20 dB)

Signal-to-noise ratio...............62 dB (IEC -A network)

Bluetooth

Versio n ..........................................Bluetooth 3.0 certified

Output power ............................+ 4 dBm M axi mum

(Power class 2)

Note

Specifications and the design are subject to mod­ifications without notice.

Backup current......................... 4.0 mA or less

2.1 SPECIFICATIONS

6

DEH-X5600BT/XNEW5

5 678

56

7

8

C

D

F

A

B

E

General

Power source ...................14.4 V DC (10.8 V to 15.1 V al-

lowable)

Grounding system ............Negative type

Maximum current consumption

..................................10.0 A

Dimensions (W × H × D):
DIN

Chassis ............................ 178mm × 50 mm × 165 mm

(7 in. × 2 in. × 6-1/2 in.)

Nose ................................ 188mm × 58mm × 15 mm

(7-3/8 in.× 2-1/4 in.× 5/8 in.)

D

Chassis ............................ 178mm × 50 mm × 165 mm

(7 in.× 2 in.× 6-1/2 in.)

Nose ................................ 170mm × 46mm × 15 mm

(6-3/4 in.× 1-3/4 in.× 5/8 in.)

Weight ............................. 1 kg (2.2 lbs)

Audio

Maximum power output ... 50 W × 4

70 W × 1/2 Ω (for subwoofer)

Continuous power output

................................... 22W × 4 (50Hz to 15 000Hz,

5 % THD, 4 Ω load, both chan-

nels driven)

Load impedance .............. 4 Ω (4 Ω to 8 Ω allowable)

Preout maximum output level

................................... 2.0 V

Loudness contour ............ +10dB (100Hz), +6.5 dB

(10 kHz) (volume: –30 dB)
Equalizer (5-Band Graphic Equalizer):

Frequency........................ 80 Hz/250 Hz/800 Hz/2.5kHz/

8 kHz

Equalization range ........... ±12 dB (2 dB step)

Subwoofer (mono):

Frequency........................ 50 Hz/63Hz/80 Hz/100 Hz/

125 Hz/160 Hz/200 Hz

Slope ...............................–12 dB/oct,–24 dB/oct

Gain ................................ +6 dB to –24 dB

Phase .............................. Normal/Reverse

CD player

System ............................Compact disc audio system

Usable discs ....................Compact disc

Signal-to-noise ratio ......... 94 dB (1 kHz) (IHF-A network)

Number of channels ........ 2 (stereo)

MP3 decoding format ...... MPEG-1 & 2 Audio Layer 3

WMA decoding format ..... Ver. 7, 7.1, 8, 9, 10, 11, 12 (2 ch

audio)
(Windows Media Player)

WAV signal format ...........Linear PCM & MS ADPCM

(Non-compressed)

USB

USB standard specification

................................... USB 2.0 full speed

Maximum current supply

................................... 1A

USB Class ....................... MSC (Mass Storage Class)

File system....................... FAT12, FAT16, FAT32

MP3 decoding format ...... MPEG-1 & 2 Audio Layer 3

WMA decoding format ..... Ver. 7, 7.1, 8, 9, 10, 11, 12 (2 ch

audio)
(Windows Media Player)

WAV signal format ...........Linear PCM & MS ADPCM

(Non-compressed)

FM tuner

Frequency range ..............87.9 MHz to 107.9 MHz

Usable sensitivity ............. 9dBf (0.8 µV/75Ω, mono, S/N:

30 dB)

Signal-to-noise ratio ......... 72dB (IHF-A network)

AM tuner

Frequency range .............. 530 kHz to 1 710 kHz

Usable sensitivity ............. 25µV (S/N: 20 dB)

Signal-to-noise ratio ......... 62dB (IHF-A network)

Bluetooth

(DEH-X6600BS)

Version ............................Bluetooth 3.0 certified

Output power ................... +4dBm Maximum

(Power class 2)

CEA2006 Specifications

Power output ................... 14 W RMS × 4 Channels (4 Ω

and

1 % THD+N)

S/N ratio .......................... 91dBA(reference: 1 W into

4 Ω)

Note

Specifications and the design are subject to
modifications without notice.

Backup current.................. 4.0 mA or less

DEH-X6600BS/XNUC, DEH-X3600S/XNUC

Securing the front panel

The front panel can be secured with the sup­plied screw.

Screw
(BPZ20P060FTC) (UC)
(XXX7020) (Except UC)

DEH-X5600BT/XNEW5

7

1234

1234

C

D

F

A

B

E

DEH-X3600UI/XNEW5

General

Power source ...................14.4 V DC (10.8 V to 15.1 V al-

lowable)

Grounding system ............Negative type

Maximum current consumption

...................................10.0 A

Dimensions (W × H × D):
DIN

Chassis ............................ 178mm × 50 mm × 165 mm

Nose ................................ 188mm × 58mm × 15 mm

D

Chassis ............................ 178mm × 50 mm × 165 mm

Nose ................................ 170mm × 46mm × 15 mm

Weight ............................. 1 kg

Audio

Maximum power output ... 50 W × 4

70 W × 1/2 Ω (for subwoofer)

Continuous power output

................................... 22W × 4 (50Hz to 15 000Hz,

5 % THD, 4 Ω load, both chan-

nels driven)

Load impedance .............. 4 Ω (4 Ω to 8 Ω allowable)

Preout maximum output level

................................... 2.0 V

Loudness contour ............ +10dB (100Hz), +6.5 dB

(10 kHz) (volume: –30 dB)
Equalizer (5-Band Graphic Equalizer):

Frequency........................ 80 Hz/250 Hz/800 Hz/2.5kHz/

8 kHz

Equalization range ........... ±12 dB (2 dB step)

Subwoofer (mono):

Frequency........................ 50 Hz/63 Hz/80 Hz/100Hz/

125 Hz/160 Hz/200 Hz

Slope ...............................–12 dB/oct, –24 dB/oct

Gain ................................ +6 dB to –24dB

Phase .............................. Normal/Reverse

CD player

System ............................Compact disc audio system

Usable discs .................... Compact disc

Signal-to-noise ratio ......... 94dB (1 kHz) (IEC-A network)

Number of channels ........ 2 (stereo)

MP3 decoding format ...... MPEG-1 & 2 Audio Layer 3

WMA decoding format ..... Ver. 7, 7.1, 8, 9, 10, 11, 12 (2 ch

audio)
(Windows Media Player)

WAV signal format ........... Linear PCM & MS ADPCM

(Non-compressed)

USB

USB standard specification

................................... USB 2.0 full speed

Maximum current supply

................................... 1A

USB Class ....................... MSC (Mass Storage Class)

File system....................... FAT12, FAT16, FAT32

MP3 decoding format ...... MPEG-1 & 2 Audio Layer 3

WMA decoding format ..... Ver. 7, 7.1, 8, 9, 10, 11, 12 (2 ch

audio)
(Windows Media Player)

WAV signal format ........... Linear PCM & MS ADPCM

(Non-compressed)

FM tuner

Frequency range .............. 87.5 MHz to 108.0MHz

Usable sensitivity ............. 9dBf (0.8µV/75 Ω, mono, S/N:

30 dB)

Signal-to-noise ratio ......... 72 dB (IEC-A network)

MW tuner

Frequency range .............. 531 kHz to 1602 kHz

Usable sensitivity ............. 25 µV (S/N: 20dB)

Signal-to-noise ratio ......... 62dB (IEC-A network)

LW tuner

Frequency range .............. 153 kHz to 281 kHz

Usable sensitivity ............. 28 µV (S/N: 20dB)

Signal-to-noise ratio ......... 62 dB (IEC-A network)

Note

Specifications and the design are subject to
modifications without notice.

Backup current..................... 4.0 mA or less

The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc.
and any use of such marks by Pioneer Corporation is under license.
Other trademarks and trade names are those of their respective owners.

2.2 DISC/CONTENT FORMAT

8

DEH-X5600BT/XNEW5

5 678

56

7

8

C

D

F

A

B

E

demrifnocebotmetIserudecorP.oN

1 Confirm whether the customer complain has

been solved.
If the customer complain occurs with the
specific media, use it for the operation check.

The customer complain must not be
reappeared.
Display, audio and operations must be
normal.

2 CD Play back a CD.

(Track search)

No malfunction on display, audio and
operation.

3 FM/AM tuner Check FM/AM tuner action.

(Seek, Preset)
Switch band to check both FM and AM.

Display, audio and operations must be
normal.

4 Check whether no disc is inside the product. The media used for the operating check must

be ejected.

retfaecnaraeppastinotridrosehctarcsoNkcehcecnaraeppA5

receiving it for service.

Item to be checked regarding audio

A

B

Keyboard Unit

D

BT Unit
X5600BT/XNEW5
X6600BS/XNUC

Tuner Amp Unit

C

CD Core Unit (S11.6VA)

A:DEH-X5600BT/XNEW5
B:DEH-X6600BS/XNUC
C:DEH-X3600S/XNUC
D:DEH-X3600UI/XNEW5
Unit Number : QWM3677(A)
Unit Number : QWM3678(B)
Unit Number : QWM3679(C)
Unit Number : QWM3627(D)
Unit Name : Tuner Amp Unit
Unit Number : (A,D)
Unit Number : (B,C)
Unit Name : Keyboard Unit
Unit Number : CWX4269
Unit Name : CD Core Unit(S11.6VA)
Unit Number : QWM3750(A,B)
Unit Name : BT Unit

3. BASIC ITEMS FOR SERVICE

3.1 CHECK POINTS AFTER SERVICING

To keep the product quality after servicing, please confirm following check points.

See the table below for the items to be checked regarding audio:

Distortion
Noise

Volume too low
Volume too high
Volume fluctuating
Sound interrupted

3.2 PCB LOCATIONS

DEH-X5600BT/XNEW5

9

1234

1234

C

D

F

A

B

E

3.3 JIGS LIST

- Jigs List

- Grease List

Name

Grease
Grease

Grease No.

GEM1024
GEM1043

Remarks

CD Mechanism Module
CD Mechanism Module

N

G

Name

16P FFC
Test Disc
L.P.F.

Jig No.

GGD1310
TCD-782

Remarks

Tuner Amp Unit - CD Core Unit
Checking the grating
Checking the grating (Two pieces)

Before shipping out the product, be sure to clean the
following portions by using the prescribed cleaning
tools:

Portions to be cleaned Cleaning tools

CD pickup lenses Cleaning liquid : GEM1004

Cleaning paper : GED-008

ame

3.4 CLEANING

rease No.

emarks

10

DEH-X5600BT/XNEW5

5 678

56

7

8

C

D

F

A

B

E

DEH-X5600BT/XNEW5

11

1234

1234

C

D

F

A

B

E

4. BLOCK DIAGRAM

5

4

AUX

6

SXMG0

SXML0

SXML0

SXMR0

JA892

(2/2)

10

6

2

9

SXITOSYS

SYSTOSXI

SXML0 SXML0

TUNL

1

B.UP

JA961

SXIPW

2423

9

TC7SH126FU

IC602

JA891

2

3

1

WIRED

REMOTE

WIRED

REMOTE

KEYAD

KEYD

GND

8

BT3.3V

VOUT

3

VIN

JA401

1

2,3

CN701

FM/AM ANTENNA

ILMPW

18

VDD3.3V

9

SWVDD

SW5V

9

6

BSEN

SYSPW

SWVD

SXITX

SXIRX

SXIPW

1

11

108

137

8

3

CDRS

8

RESET 39

2

B.UP

4

10

SYS+B

SWVDD

VDD12

SW5V

SYS+B

BSENS

SW5VCNT

+B

VCC

EN

DDON

VIN

EN

OC

+BUP

VDDCONT

SYSPW

5

USB5V

VOUT

5

SYNCSYNC

USBC

USBF

1425

276

1

8

143

1

3

1444

B.UP

Q751

2

1

Q752

VDCO

103

VDSE

65

MECHA VD

VD

B.UP

VDD

BD9876EFJ

IC551

BD2232G-G

IC552

SY

C

R5S

REGULATOR IC

IC911

BA49183-V12

FM/AM TUNER

IC401

TDA7706

5

FMMIXIN1

16

PINDIN

18

LNAIN

SYSTEM MICRO

COMPUTER

(1/2)

IC601

R5S726B0D216FP

VDD1.2V

VDD3.3V

VDD

8

7

TUN_SDA

TUN_SCL

33

34

57

112

111

TUN_RST

31

106

KEYAD

66

KEYD

123

I2CSDA

RSTN

I2CSCL

DACOUTL

RESET

47

SXI TUNER

FLASH ROM

IC681

CD DATA (CDSRQ,CDSTBY,SKIP,
SCL,SDA,DATA,BCLK,LRCK,WAIT)

TUNER AMP UNIT

A

USB5V REGULATOR

FB

LX

4

BST

7

6

8

109

31

110

730

2

SCL

RST

VCC

SDA

iPod CP

IC531

337S3959

VDD3.3V

Q531

P1001

BT MODULE

BT UNIT

6

4

2

BTTOSYS

SYSTOBT

BTDATA

NRST_CPU

BTLRCK

BTBCK

7

12

8

11

13

15

10

5

9

21

20

MIC1N

MIC1P

MIC1N

MIC1P

2

3

1

KEYAD

KEYD

GND

5

4

JA892

JA892

CN971CN23CN21

D

MIC1N

MIC1P

RMIC

6

MIC1N

MIC1P

161

152

VCC

5

6

4

22

MIC-BIAS

10117

6

BTRX

BTTX

BTRST

BTDATA

BT_BCK

16

17

6

4

7

2

BT_LRCK

11

12

13

7

BTTOSYS

SYSTOBT

BTDATA

RESET

BTTOSYS

SYSTOBT

BTDATA

NRST_CPU

16

15

BTLRCK

BTSCK

BTRLCK

BTSCK

VCC

BT3.3V REG.

IC22

S-1206B33-U3

2

6

VIN

VOUT

1

BT1.8V REG.

IC21

S-1172B18-E6

ON/OFF

3

BT1.8V

BT18ON

CP_SCL

CP_SDA

CPPWR

CPRST

ILMPW

B.UP

ILM+B

Q872

Q871

CD CORE UNIT(S11.6 VA)

M

LD

MD

SPINDLE

M

LOADING/CARRIAGE

LD+

MD

10

11

HOLOGRAM

RF AMP, CD DECODER

2

VD

VD

9

3

SPO+

2

SPO-

5

SLLDO+

4

SLLDO-

22

LDIN

21

MUTE

TD,FD

AC,BD,VC,E,F

SD,MD

1

LD

2

PD

CONT

LOEJ

HOME

35

41

39

VDD

1

VDD

VDD

10

11

FOCUS ACT.

TRACKING ACT.

FOP

TOP

2

1

TOP

FOP

7

TKO-

10

FCO+

2

1

DSCSNS

38

29

RESET

8

RESET

88

VREF

REFO

93

REFOUT

3

3

FOM

FOM

8

TKO+

4

4

TOM

TOM

9

FCO-

23

CNT

CLCONT

40

54

PUEN

V+3A

VDD

UNIT

MOTOR

MOTOR

ACTUATOR/

MOTOR DRIVER

BD8223EFV

HOMEDSCSNS

PEQ094A

DIGITAL SERVO/DATA • PROCESSOR

CPU

CN701

Q101

CN101

Q102

IC301

S901

S903

IC201

C

V+3A

7

7

VCC

PD

REFO

SOP

SOM

LCOP
LCOM

PICKUP UNIT
(P11)(SERVICE)

LD

CD DATA (CDSRQ,CDSTBY,SKIP,
SCL,SDA,DATA,BCLK,LRCK,WAIT)

B

A

DBA

D

C

4252

IC603

TC7SET08FUS1

1

RESET

IC671

S-80827CNMC-B8M

OUT

2

VDD

VDD3.3V

D

:PEB094A8

:PEB101A8

:PEB110A8

:PEB095A8

A
B
C

(2/2)

(1/2)

CBA

12

DEH-X5600BT/XNEW5

5 678

56

7

8

C

D

F

A

B

E

32

PB17/A17/MOSI0

TEL

9

Q951

TELIN

10

2423

9

IC602

:DEH-X5600BT/XNEW5
:DEH-X6600BS/XNUC

A
B

:DEH-X3600UI/XNEW5

D

:DEH-X3600S/XNUC

C

B.UP

141

14

MUTE

DCSENS

107

ASENS

OUT1-

OUT1+

OUT2-

OUT2+

FL-

FL+

RL-

RL+

ACC

Q941

MUTE

OFF.DET

CN801

ASENS

13

7

5

1

3

18

JA901

18

10

8

SOURCE

DPDT

KYDT

SSENS

43

ROT0

63

ROT1

64

DPDT

29

KYDT

28

IN2

20

DSENS

DSENS

42

DM

59

DP

60

IN1

MUTE

BSENS

SYSPW

SWVDD

SXITX

SXIRX

SXIPW

108

137

8

CDRST

39

4

B.UP

EN

DDON

5

AUXL

19

SYNCSYNC

USBCTL

USBFLG

1425

276

143

144

B.UP

VDCONT

103

VDSENS

65

SYSTEM MICRO

COMPUTER

(2/2)

IC601

R5S726B0D216FP

POWER AMP

IC301

PA2032A

Q301

(1/2)

Q301

(2/2)

JA251

Q251

INAP2L

39

34

OUTRL

33

OUTFL

35

OUTPL

ELECTRONIC VOLUME/

SOURCE SELECTOR

IC201

PM9013A

37

INBP4L

MCLK

LRCLK

BCLK

DIN

DATA

RESETB

CLK

STB

EVOL_RST

EVOL_CK

EVOL_DT

EVOL_DATA

EVOL_BRCK

EVOL_LRCK

EVOL_MCK

EVOL_CS

19

20

21

22

23

26

24

25

99

122

121

127

131

105

129

132

11

USB5V

4

6

ROT0

ROT1

DM

DP

13

15

42

IC801

TC7SET08FUS1

ILM+B

3

SWVDD

SXML0

IN5L

36

TUNL

AUXL

POWER SUPPLY

SWL

5

SWL

2

RL

6

FL

T

P251

PREOUT

PL

RL

FL

RGBCS

RGBCK

RGBST/ILMCLR2

RGBCK/ILMCLR1

20

19

14

RGBDT

RGBDT

21

7

12

ILM+B

4

3

2

1

SOURCE

18

S1842

USB

USB5V

DM

DP

11

13

15

2

3

4

USB5V

DM

DP

CN1911

KEY MATRIX

4

6

2

1

5

4

3

AUXL

ROT0

ROT1

KDT2

KST1

19

LCD DRIVER/

KEY CONTROLLER

MULTI-CONTROL

PDC202B

LCD

98

93

P03

92

P02

91

P01

90

P00

97

P07

96

P06

95

P05

94

P04

KST3

KST2

KST1

KST0

KDT3

KDT2

KDT1

KDT0

CN1931

S1830

IC1802

V1802

JA1921

FRONT AUX

AUXL

AUXGND 1

2

AUXR 3

RGBDT

RGBST

RGBCK

7

14

12

RGB DRIVER

IC1851

BH2228FV

BLUE Key

10

12

CSB

11

CLK

DI

1

AO1

ILM+B

6

AO6

5

AO5

4

AO4

2

AO2

3

AO3

GREEN Key

RED Key

RED LCD

GREEN LCD

BLUE LCD

Q1859

D1882,

Q1858 Q1857

Q1868

D1885,
D1886

Q1867 Q1866

ILM+B ILM+B

PNJ4833M

SENSOR

REMOTE CONTROL

IC1941

1

KYDT

DPDT

10

8

100

99

URX/P35

UTX/P34

3

DSENS

20

SWVDD

5

ILM+B

KEYBOARD UNIT

B

D1883,
D1884

CB

AD

RMIN/P73/INT/T0IN

Q1852(1/2)

Q1853(1/2)

Q1853(2/2)

Q1851(1/2)

Q1851(2/2)

Q1852(2/2)

BREM&A.ANT

CD

14

Q252 Q253

B

ADC

B

4252

IC603

7SET08FUS1

VDD3.3V

VDD3.3V

SXIPWSENS

69

7

8

GND

GND

CBA

SORUCE

10(9)

8(7)

4(3)

6(5)

23(22)

2(1)

12(11)

13(12)

26(25)

15

B.UP

17

FUSE 10A

DEH-X5600BT/XNEW5

13

1234

1234

C

D

F

A

B

E

5. DIAGNOSIS

Vcc = 1.2 V

PVcc = 3.3 V

BSENS

Pin 108

ASENS

Pin 107

DSENS

Pin 42

BSENS = L

DSENS = L

Starts

communication

with Grille

microcomputer.

SWVDD <- H

Pin 137

Source keys

operative

Source ON

SYSPW <- H

Pin 8

300 ms

300 ms

In case of the above signal, the communication
with Grille microcomputer may fail.
If the time interval is not 300 msec, the oscillator
may be defective.

Completes power-on operation.
(After that, proceed to each source operation)

Power ON

ASENS = L

Vcc : Pin 15, 26, 51, 93, 104, 130
PVcc : Pin 3, 11, 22, 34, 44, 58, 81, 89, 100, 119, 126, 135

5.1 OPERATIONAL FLOWCHART

14

DEH-X5600BT/XNEW5

5 678

56

7

8

C

D

F

A

B

E

8-digit display 6-digit display 4-digit display

ERROR-xx ERR-xx E-xx

(2) LIST OF CD ERROR CODES (Error Mode: 0xFD)

Code Classification

Error code to be displayed

Details and possible causes

10 Servo Carriage Home NG The pickup cannot move toward the inner track.

The CRG cannot move from the inner track.

--> Defective HOME SW; Failure in CRG movement.

07 Servo TOC reading NG TOC information cannot be read.

--> The partial disk or TOC content is illegal.

11 Servo Focus NG Focusing not available

--> Disc placed upside-down; Stains on the disc; excessive vibration.

17 Servo Setup NG The laser output cannot be adjusted. Focus can be easily lost.

--> Scratches or stains on the disc; excessive vibration.

15 Servo RF NG The digital signal from the disc cannot be detected.

--> A CD-R/RW disc that does not contain data loaded.

12 Servo Spindle Lock NG

Subcode NG
RF-amp NG

Spindle not locked. Subcode not readable.
Proper RF AMP gain not obtained.

--> Defective spindle; Scratches or stains on the disc; excessive vibration.

-->

A CD-R/RW disc that does not contain data loaded, or in a rare case, disc placed upside-down.

--> RF signal error.

30 Servo Search Time Out Failed to reach a target address. And, the search became a timeout.

--> Carriage/Tracking error; Scratches on the disc; Stains on the disc

50 Mechanism Load NG

Eject NG

Disc loading/ejection not completed

--> A foreign object inserted in the mechanism; Disc jammed.

51 Mechanism Failure in retried

turning for ejection

Disc could not be ejected even after disc turning had been retried.

--> A foreign object inserted in the mechanism; Disc jammed.

ERROR CODES

(1) DISPLAY METHOD

If “0xFD” error mode is displayed in CD MODE (CD MODE area for display), an error code will be displayed in the MIN (minute
display) and SEC (second display) areas.

The same code is displayed in the MIN and SEC areas.
The TNO area is blank (#0FFH), as it conventionally was.

• Display example of the head unit
Depending on the display capability of LCDs, the display format varies, as shown below. XX denotes an error number.
Note: In a case of an OEM product, the error display format is subject to the specifications used by the equipment
manufacturer.

If a CD memory device is inoperable, or operation of such media is stopped by an error, the error mode is established and a
cause of the error is displayed by an error code. Indication of error codes is intended to reduce the number of calls from
customers and facilitate failure analysis and repair work in servicing.

• The 2 high-order digits of an error code denote the main classification, shown below.
code classification
0x
1x Servo-related errors
3x
5x Mechanism-related errors

• How to restore from each error is shown below.
Servo-related errors(0X, 1X, 3X) : Servo-related errors CD Off, Eject, ACC Off, Back-up Off, Communication reset, Reset
Load NG/Eject NG(50) : Reload, Eject, ACC Off, Back-up Off, Communication reset, Reset
Failure in retried turning for ejection : CD On, Eject, ACC Off, Back-up Off, Communication reset, Reset

NOTES

• Indications of error codes are available only during disc operations, because CD operations are unavailable if a mechanical error is

generated.

• If the TOC cannot be read, It stops because of error 07.

• If you design a new head unit, be sure to use one of the display formats indicated in “Display example of the head unit.”

5.2 ERROR CODE LIST

DEH-X5600BT/XNEW5

15

1234

1234

C

D

F

A

B

E

Symptoms are written in bold and causes in reg­ular, non-indented text. Regular, indented text is
used to indicate actions to be taken.

Common

AMP ERROR

This unit fails to operate or the speaker connection is
incorrect; the protective circuit is activated.

Check the speaker connection. If the message
fails to disappear even after the engine is
switched off/on, contact your dealer or an
authorized Pioneer Service Station for
assistance.

CD player

ERROR-07, 11, 12, 17, 30

The disc is dirty.

Clean the disc.

The disc is scratched.

Replace the disc.

ERROR-07, 10, 11, 12, 15, 17, 30, A0

There is an electrical or mechanical error.

Turn the ignition switch OFFand back ON, or
switch to a different source, then back to the CD
player.

ERROR-15

The inserted disc is blank.

Replace the disc.

ERROR-23

Unsupported CD format.

Replace the disc.

FORMAT READ

Sometimes there is a delay between the start of play­back and when you start to hear any sound.

Wait until the message disappears and you hear
sound.

NO AUDIO

The inserted disc does not contain any playable files.

Replace the disc.

SKIPPED

The inserted disc contains DRM protected files.

The protected files are skipped.

PROTECT

All the files on the inserted disc are embedded with
DRM.

Replace the disc.

USB storage device/iPod

FORMAT READ

Sometimes there is a delay between the start of play­back and when you start to hear any sound.

Wait until the message disappears and you hear
sound.

NO AUDIO

There are no songs.

Transfer the audio files to the USB storage device
and connect.

The connected USB storage device has security en­abled.

Follow the USB storage device instructions to
disable the security.

SKIPPED

The connected USB storage device contains DRM
protected files.

The protected files are skipped.

PROTECT

All the files on the connected USB storage device
are embedded with DRM.

Replace the USB storage device.

N/A USB

The connected USB device is not supported by this
unit.

 Connect a USB Mass Storage Class compliant
device.
 Disconnect your device and replace it with a
compatible USB storage device.

CHECK USB

The USB connector or USB cable has short­circuited.

Check that the USB connector or USB cable is
not caught in something or damaged.

CHECK USB

The connected USB storage device consumes more
than maximum allowable current.

Disconnect the USB storage device and do not
use it. Turn the ignition switch to OFF, then to
ACC or ON and then connect only compliant
USB storage devices.

CHECK USB

The iPod operates correctly but does not charge.

Make sure the connection cable for the iPod has
not shorted out (e.g., not caught in metal
objects). After checking, turn the ignition switch
OFF and back ON, or disconnect the iPod and
reconnect.

16

DEH-X5600BT/XNEW5

5 678

56

7

8

C

D

F

A

B

E

ERROR-19

Communication failed.

Perform one of the following operations.
–Turn the ignition switch OFF and back ON.
–Disconnect the USB storage device.
–Change to a different source.
Then, return to the USB source.

iPod failure.

Disconnect the cable from the iPod. Once the
iPod’s main menu is displayed, reconnect the
iPod and reset it.

ERROR-23

USB storage device was not formatted with FAT12,
FAT16 or FAT32.

USB storage device should be formatted with
FAT12, FAT16 or FAT32.

ERROR-16

The iPod firmware version is old.

Update the iPod version.

iPod failure.

Disconnect the cable from the iPod. Once the
iPod’s main menu is displayed, reconnect the
iPod and reset it.

STOP

There are no songs in the current list.

Select a list that contains songs.

NOT FOUND

No related songs.

Transfer songs to the iPod.

Bluetooth device

ERROR-10

The power failed for the Bluetooth module of this
unit.

Turn the ignition switch OFFand then to ACC or
ON.
If the error message is still displayed after
performing the above action, please contact your
dealer or an authorized Pioneer Service Station.

Pandora

ERROR-19

Communication failed.

Disconnect the cable from the device. Once the
device’s main menu is displayed, reconnect the
device and reset it.

START UP APP

The Pandora application has not started running yet.

Start up the Pandora application.

INOPERABLE

The operation was disabled.

Run the same command for another track.

TRYAGAIN

Unable to save thumb rating.
Unable to save BookMark.
Unable to add station.

Try again later.

MAINTENANCE

Pandora system is undergoing maintenance.

Try again later.

SKIP LIMIT

Skip limit reached.

 Do not exceed the skip limit.
 Due to music licensing restrictions, Pandora

limits the total number of skips per hour.

CHECK APP

This version of the Pandora application is not sup­ported.

Connect a device that has a compatible version
of the Pandora application installed.

CHECK DEVICE

Device error message displayed in Pandora applica­tion.
Unable to play music from Pandora.

Please check your connected device.

NO STATION

No station found.

Create a station in the Pandora application on
your connected device.

NO ACTIVE ST

No station selected.

Select a station.

NO BT DEVICE GO TO BT MENU TO REGISTER

No Bluetooth device found.

Follow the instructions that appear on the
screen.

CONN. FAILED PRESS BAND KEY TO RETRAY

Bluetooth connection failed.

Follow the instructions that appear on the
screen.

CHECK APP PRESS BAND KEY TO RETRAY

Connection to the Pandora application failed.

Follow the instructions that appear on the
screen.

DEH-X5600BT/XNEW5

17

1234

1234

C

D

F

A

B

E

DISCONNECTED PRESS BAND KEY TO RETRAY

Bluetooth connection failed.

Follow the instructions that appear on the
screen.

CHECK APP

Connection to the application failed.

Follow the instructions that appear on the
screen.

START UP APP

The application has not started running yet.

Follow the instructions that appear on the
screen.

SiriusXM Satellite Radio

CHECK ANTENNA

The antenna connection is incorrect.

Check the antenna connection. If the message
fails to disappear even after the engine is
switched off/on, contact your dealer or an
authorized Pioneer Service Station for
assistance.

CHECK TUNER

The SiriusXM Connect Vehicle Tuner connection is
incorrect or the power failed.

Check the tuner connection and battery voltage.
If the message fails to disappear even after the
engine is switched off/on, contact your dealer or
an authorized Pioneer Service Station for
assistance.

NO SIGNAL

The SiriusXM Connect Vehicle Tuner is having diffi­culty receiving the SiriusXM satellite signal.

 Verify that your vehicle is outdoors with a clear
view of the southern sky.

 Verify that the SiriusXM magnetic mount
antenna is mounted on a metal surface on the
outside the vehicle.
 Move the SiriusXM antenna away from any
obstructions.

SUBSCRIPTION UPDATED

This unit has detected a change in your SiriusXM
subscription status.

Press any key to clear the message.

CH UNAVAIL

The channel that you have requested is not a valid
SiriusXM channel.

Check the SiriusXM channel lineup.

CHAN UNSUB

The channel that you have requested is not included
in your SiriusXM subscription package.

Check the content of your SiriusXM subscription
package.

CH LOCKED

Locked by the radio Parental Control feature.

Release the channel lock.

DISCONNECTED PRESS BAND KEY TO RETRAY

Bluetooth connection lost.

Follow the instructions that appear on the
screen.

STATION FULL

A new station cannot be added.

Delete an old station to open a spot for a new
one.

CAN.T DELETE

The station could not be deleted.

Run the same command for another station.

NO NETWORK

The connected device is out of area.

Connect the connected device to a network.

NO SERVICE

The connected device is out of area.

Connect the connected device to a network.

CAN.T PLAY

The operation was disabled.

Run the same command for another station.

Apps

NO BT DEVICE GO TO BT MENU TO REGISTER

No Bluetooth device found.

Follow the instructions that appear on the
screen.

CONN. FAILED PRESS BAND KEY TO RETRAY

Bluetooth connection failed.

Follow the instructions that appear on the
screen.

18

DEH-X5600BT/XNEW5

5 678

56

7

8

C

D

F

A

B

E

ANTENNA INPUT

1 FL+
2 FR+
3 FL­4 FR­5 RL+
6 RR+
7 RL­8 RR-

9 NC
10 NC
11 NC
12 NC
13 ACC
14 B.REM
15 B.UP
16 GND

WIRED

REMOTE

CONTROL

REAR OUTPUT or

SUBWOOFER OUTPUT

FRONT

OUTPUT

16

14

12

10 8

6

42

15

13

11

97

5

31

MICROPHONE

INPUT

(DEH-X5600BT)

AUX2 INPUT

(DEH-X3600UI)

DEH-X5600BT/XNEW5
DEH-X3600S/XNUC
DEH-X3600UI/XNEW5

DEH-X6600BS/XNUC

ANTENNA INPUT

WIRED

REMOTE

CONTROL

SUBWOOFER OUTPUT

REAR OUTPUT

FRONT

OUTPUT

MICROPHONE

INPUT

1 SXiL
2 SXiTX
3 NC
4 SXiR
5 SXiG
6 SXiRX
7 NC
8 GND
9 SXi PW
10 SXiPW

Sirius XM BUS

Sirius XM BUS(Except DEH-X3600UI)

Sirius XM BUS

5.3 CONNECTOR FUNCTION DESCRIPTION

DEH-X5600BT/XNEW5

19

1234

1234

C

D

F

A

B

E

6. SERVICE MODE

Grille condition

Conf. item Operate Show LCD RGB

All light up

PHONE (DEH-X5600BT,
DEH-X6600BS),
MIX (DEH-X3600S,
DEH-X3600UI) + LIST

Draw 1 White

All light off SOURCE No light Draw2 No light

Conf. LCD pattern 1

(* And change ILM color)

BAND Draw 3

Red

Conf. LCD pattern 2

ROTARY center

Draw 4 Green

Drawings Style

Draw1 ALL light up
Draw2 ALL light off

Draw3

Draw4

BAND

SOURCE

PHONE
(DEH-X5600BT,
DEH-X6600BS)
MIX
(DEH-X3600S,
DEH-X3600UI)

LIST

ROTARY

Press and hold "PHONE (DEH-X5600BT, DEH-X6600BS), MIX (DEH-X3600S, DEH-X3600UI)" and "LIST" buttons together,
and turn BUP and ACC on.

[How to enter Test mode]

6.1 DISPLAY TEST MODE 1

20

DEH-X5600BT/XNEW5

5 678

56

7

8

C

D

F

A

B

E

* Initial
condition

$ PD number

For Ver.7.01, "701" is displayed

For PEA010A, "010A" is displayed

# System
microcomputer
version

S

$$$$

###

1 + 3

On (state when
entering test mode)

Press and hold "1" and "3" buttons together, and turn BUP and ACC on.

[Operation key]

[How to enter Test mode]

[Test items]

Start display test mode.
Press and hold "1" and "3" buttons together, and turn
BUP and ACC on.

Display is normally updated

Display update is stopped

Product operation is performed as usual, in appearance.

The screen gets still when entering this item.

On (an initial value)

On (lighting condition
of normal times)

On (an initial value or
setting value of default
menu)

On (an initial value or
setting value of default
menu)

On (an initial value or
setting value of default
menu)

Off

All off

All off

All off

Remarks

Key Illumination

Operation key Processing

Icon

Enter display test mode
Switch to next test mode

The information such as the system microcomputer version is checked.

Switching to next display
by pressing “ 1 ” + “ 3 ” buttons together.

Switching to next display
by pressing “ 1 ” + “ 3 ” buttons together.

Switching to next display
by pressing “ 1 ” + “ 3 ” buttons together.

System Version information is displayed.

6.2 DISPLAY TEST MODE 2

DEH-X5600BT/XNEW5

21

1234

1234

C

D

F

A

B

E

6.3 SOFTWARE VERSION UP METHOD

Overview

This mode is used for upgrading the MCU software of system using USB memory.

How to enter in USB rewriting mode

Press and hold "1" and "2" buttons together, and turn BUP and ACC on.

USB rewriting operation flow

Explanatory note

Screen display and ON/OFF of illumination

Characters displayed on the screen

Red frame: illumination lights up

Gray frame: illumination lights off

Blue characters: operation to be carried out by a user of USB rewriting function

Press and hold "1" and "2" buttons together, and turn BUP and ACC on.

Press LIST button

* After connecting USB memory in which upgrading file is stored, press LIST button.

(4) Retry count over

Retry rewriting

Check of upgrading file is started

(2) Upgrading file is not detected
Upgrading file error

After retryFirst time

Rewriting is started

Switched every
5 seconds

(3) Rewriting failed

(1) Rewriting succeeded

Result of rewriting

(1) Rewriting succeeded

(2) Upgrading file error
Upgrading file is not detected

(3) Rewriting failed

(4) Retry count over

FILE ERROR

DON'T STOP

PRG **/100

ERR->RETRYCAN'T UPDT

USB

START UPDT

CHECK FILE

In 5 seconds, usual operation
(OFF SOURCE)

As the reset is internally carried out,
display and illumination go out

In 5 seconds, usual operation
(OFF SOURCE)

In 5 seconds, rewriting
is retried

In 5 seconds, rewriting
is retried

Display is continued until
the power supply is turned
OFF

If the power supply is turned OFF
during rewriting, retry the rewriting.

Displayed when there is no upgrading file in USB memory or the data of upgrading file is different.
In 5 seconds, usual operation (OFF SOURCE) is started.
If the upgrading file error is detected or the upgrading file is not detected after the rewriting is retried, the rewriting is failed.
In 5 seconds, rewriting is retried.

Displayed when the retry becomes unavailable because the retry count is exceeded.
The display is continued until the power supply is turned OFF. If the power supply is turned ON again, the display is not changed.
The upgrading using USB is disabled, so it is necessary to write programs in serial Flash using E10A.

Displayed when the writing of upgrading file in serial Flash is not normally terminated.
Or, displayed if the upgrading file error is detected or the upgrading file is not detected after the rewriting is retried.
In 5 seconds, rewriting is retried.

Displayed when USB rewriting is normally terminated.
In 5 seconds, usual operation (OFF SOURCE) is started.

ERR->RETRY

COMPLETE

22

DEH-X5600BT/XNEW5