Pioneer DEH-P500UB User Manual
Installation English Installation English Connecting the unit English
53
182182
DEH-P500UB
INSTALLATION MANUAL
MANUEL D’INSTALLATION
Note
Check all connections and systems before final in-
•
stallation.
Do not use unauthorized parts. The use of unau-
•
thorized parts may cause malfunctions.
Consult with your dealer if installation requires drill-
•
ing of holes or other modifications of the vehicle.
Do not install this unit where:
•
it may interfere with operation of the vehicle.
—
it may cause injury to a passenger as a result
—
of a sudden stop.
The semiconductor laser will be damaged if it over-
•
heats. Install this unit away from hot places such as
near the heater outlet.
Optimum performance is obtained when the unit is
•
installed at an angle of less than 60°.
60°
DIN Front/Rear-mount
This unit can be properly installed either from
"Front" (conventional DIN Front-mount) or
"Rear" (DIN Rear-mount installation, utilizing
threaded screw holes at the sides of unit
chassis). For details, refer to the following
installation methods.
DIN Front-mount
Installation with the rubber bush
1. Insert the mounting sleeve into the
dashboard.
• When installing in a shallow space, use a
supplied mounting sleeve. If there is enough
space behind the unit, use factory supplied
mounting sleeve.
2. Secure the mounting sleeve by
using a screwdriver to bend the
metal tabs (90°) into place.
3. Install the unit as illustrated.
Dashboard
Mounting sleeve
Rubber bush
Screw
Removing the Unit
1. Extend top and bottom of the trim
ring outwards to remove the trim
ring.
When reattaching the trim ring,
push the trim ring onto the unit until
it clicks. (If the trim ring is attached
upside down, the trim ring will not
fit properly.)
• It becomes easy to remove the trim ring if the
front panel is released.
Trim ring
2. Insert the supplied extraction keys
into both sides of the unit until they
click into place.
DIN Rear-mount
1.
Extend top and bottom of the trim
ring outwards to remove the trim
ring. When reattaching the trim ring,
push the trim ring onto the unit until
it clicks. (If the trim ring is attached
upside down, the trim ring will not
fit properly.)
• It becomes easy to remove the trim ring if the
front panel is released.
Trim ring
2. Determine the appropriate position
where the holes on the bracket and
the side of the unit match.
3. Tighten two screws on each side.
• Use either truss screws (5 mm × 8 mm) or
flush surface screws (5 mm × 9 mm), depending on the shape of screw holes in the bracket.
Dashboard or Console
Factory radio mounting bracket
Screw
Fastening the front panel
If you do not plan to detach the front panel,
the front panel can be fastened with supplied
screws and holders.
1. Attach the holders to both sides of
the front panel.
Holder
2. Replace the front panel to the unit.
3. Flip the holders into upright
positions.
4. Fix the front panel to the unit using
screws.
Screw
Note
• When this unit is installed in a vehicle without
ACC (accessory) position on the ignition switch,
red cable must be wired to the terminal that can
detect the operation of the ignition key. Otherwise,
battery drain may result.
C
C
A
O
F
N
F
O
ACC position
• Use this unit in other than the following conditions could result in fire or malfunction.
— Vehicles with a 12-volt battery and negative
grounding.
— Speakers with 50 W (output value) and 4 ohm
to 8 ohm (impedance value).
• To prevent short-circuit, overheating or malfunction, be sure to follow the directions below.
— Disconnect the negative terminal of the batter y
before installation.
— Secure the wiring with cable clamps or adhe-
sive tape. To protect the wiring, wrap adhesive
tape around them where they lie against metal
parts.
— Place all cables away from moving parts, such
as gear shift and seat rails.
— Place all cables away from hot places, such as
near the heater outlet.
— Do not pass the yellow cable through a hole
into the engine compartment to connect to a
battery.
— Cover any disconnected cable connectors with
insulating tape.
— Do not shorten any cables.
— Never cut the insulation of the power cable of
this unit in order to share the power to other
equipment. Current capacity of the cable is
limited.
— Use a fuse of the rating prescribed.
— Never wire the speaker negative cable directly
to ground.
— Never band together multiple speaker ’s nega-
tive cables.
S
T
A
R
T
No ACC position
O
F
N
F
O
S
T
A
R
T
• Control signal is output through blue/white cable
when this unit is powered on. Connect it to an external power amp’s system remote control or the
vehicle’s auto-antenna relay control terminal (max.
300 mA, 12 V DC). If the vehicle is equipped with a
glass antenna, connect it to the antenna booster
power supply terminal.
• Never connect blue/white cable to external power
amp’s power terminal. Also, never connect it to
the power terminal of the auto antenna. Otherwise, battery drain or malfunction may result.
• IP-BUS connectors are color-coded. Be sure to
connect connectors of the same color.
• Black cable is ground. This cable and other
product’s ground cable (especially, high-current
products such as power amp) must be wired separately. Otherwise, fire or malfunction may result if
they are accidentally detached.
Printed in Thailand
Imprimé en Thaïlande
<QRD3009-A/N> UC
<KSNNX> <07I00000>
3. Pull the unit out of the dashboard.
Connecting the unit English
Connecting the unit English
Connecting the unit English
Connecting the unit English
When not connecting a rear speaker lead to a subwoofer
1.5 m (4 ft. 9 in.)
20 cm
50 cm (20 in.)
iPod
Interface cable
Yellow
Connect to the constant 12 V supply terminal.
Red
Connect to terminal controlled by
ignition switch (12 V DC).
Orange/white
Connect to lighting switch terminal.
Black (chassis ground)
Connect to a clean, paint-free metal location.
USB cable
Connect to separately sold USB device.
Rear output
Front output
Antenna jack
Subwoofer output
Dock connector
Front speaker Front speaker
Left Right
Rear speaker Rear speaker
This product
Fuse (10 A)
White Gray
Green Violet
Green/black Violet/black
With a 2 speaker system, do not
connect anything to the speaker leads
that are not connected to speakers.
(7-7/8 in.)
Wired remote input
Hard-wired remote control
adaptor can be connected
(sold separately).
IP-BUS input (Blue)
IP-BUS cable
Yellow/black
If you use an equipment with Mute function,
wire this lead to the Audio Mute lead on that
equipment. If not, keep the Audio Mute lead
free of any connections.
Gray/blackWhite/black
AUX jack (3.5 φ)
Use a stereo mini plug
cable to connect with
auxiliary device.
Multi-CD player
(sold separately)
To rear output
To front output
To subwoofer
output
System remote control
Blue/white
Connect to system control terminal of the power
amp or auto-antenna relay control terminal (max.
300 mA 12 V DC).
Subwoofer
Front speaker
Rear speaker
Connect with RCA cables
(sold separately)
Perform these connections
when using the optional
amplifier.
Power amp
(sold separately)
Power amp
(sold separately)
Subwoofer
Front speaker
Rear speaker
Power amp
(sold separately)
When using a subwoofer without using the optional amplifier
50 cm (20 in.)
USB cable
Connect to separately sold USB device.
iPod
Dock connector
Interface cable
Yellow/black
If you use an equipment with Mute function, wire this lead to the Audio
Mute lead on that equipment. If not, keep the Audio Mute lead free of
any connections.
Yellow
Connect to the constant 12 V supply terminal.
Red
Connect to terminal controlled by ignition switch (12 V DC).
Orange/white
Connect to lighting switch terminal.
Black (chassis ground)
Connect to a clean, paint-free metal location.
Note:
Change the initial setting of this unit.
The subwoofer output of this unit is monaural.
1.5 m (4 ft. 9 in.)
Rear output
Front output
Antenna jack
Subwoofer output
20 cm
(7-7/8 in.)
This product
Fuse (10 A)
IP-BUS cable
AUX jack (3.5 φ)
Use a stereo mini plug
cable to connect with
auxiliary device.
Wired remote input
Hard-wired remote control adaptor can
be connected (sold separately).
IP-BUS input (Blue)
Multi-CD player
(sold separately)
Front speaker Front speaker
Left Right
Subwoofer (4 Ω) Subwoofer (4 Ω)
Not used.
Blue/white
Connect to system control
terminal of the power amp or
auto-antenna relay control
terminal (max. 300 mA 12 V DC).
When using a subwoofer of 70 W (2 Ω), be sure to connect
with Violet and Violet/black leads of this unit.
Do not connect anything with Green and Green/black leads.
Green Violet
Green/black Violet/black
White Gray
Gray/blackWhite/black
Green Violet
Green/black Violet/black
Subwoofer
(4 Ω) 2
Loading...