Pioneer BDP-80FD Operating Instruction

Blu-ray 3D™ PLAYER LECTEUR Blu-ray 3D™ REPRODUCTOR de Blu-ray 3D™
BDP-80FD
Register your product at:
Protect your new investment
The details of your purchase will be on file for reference in the event of an insurance claim such as loss or theft.
Receive free tips, updates and service bulletins on your new product
• Improve product development
Your input helps us continue to design products that meet your needs.
• Receive a free Pioneer newsletter
Registered customers can opt in to receive a monthly newsletter.
http://www.pioneerelectronics.com (États-Unis) http://www.pioneerelectronics.ca (Canada)
Operating Instructions Mode demploi
Manual de instrucciones
Thank you for buying this Pioneer product. Please read through these operating instructions so you will know how to operate your model properly. After you have finished reading the instructions, put them away in a safe place for future reference.
Operating Environment
Operating environment temperature and humidity: +5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH (cooling vents not blocked) Do not install this unit in a poorly ventilated area, or in locations exposed to high humidity or direct sunlight (or strong artificial light)
D3-4-2-1-7c*_A1_En
WARNING
This equipment is not waterproof. To prevent a fire or shock hazard, do not place any container filled with liquid near this equipment (such as a vase or flower pot) or expose it to dripping, splashing, rain or moisture.
D3-4-2-1-3_A1_En
VENTILATION CAUTION
When installing this unit, make sure to leave space around the unit for ventilation to improve heat radiation (at least 10 cm at top, 10 cm at rear, and 10 cm at each side).
WARNING
Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product, and to protect it from overheating. To prevent fire hazard, the openings should never be blocked or covered with items (such as newspapers, table-cloths, curtains) or by operating the equipment on thick carpet or a bed.
D3-4-2-1-7b*_A1_En
CAUTION
This product is a class 1 laser product classified under the Safety of laser products, IEC 60825-1:2007, but this product contains a laser diode higher than Class 1. To ensure continued safety, do not remove any covers or attempt to gain access to the inside of the product. Refer all servicing to qualified personnel.
The following caution label appears on your unit. Location: inside of the unit
D58-5-2-2b*_B1_En
CLASS 1 LASER PRODUCT
WARNING
To prevent a fire hazard, do not place any naked flame sources (such as a lighted candle) on the equipment.
D3-4-2-1-7a_A1_En
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
CAUTION:
TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
IMPORTANT
D3-4-2-1-1b_A1_En
This product contains mercury. Disposal of this material may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or the Electronics Industries Alliance : www.eiae.org.
K057_A1_En
IMPORTANT NOTICE
THE MODEL NUMBER AND SERIAL NUMBER OF THIS EQUIPMENT ARE ON THE REAR OR BOTTOM. RECORD THESE NUMBERS ON YOUR ENCLOSED WARRANTY CARD AND KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.
D36-AP9-1_A1_En
Information to User
Alterations or modifications carried out without appropriate authorization may invalidate the user’s right to operate the equipment.
D8-10-2_A1_En
CAUTION
This product satisfies FCC regulations when shielded cables and connectors are used to connect the unit to other equipment. To prevent electromagnetic interference with electric appliances such as radios and televisions, use shielded cables and connectors for connections.
D8-10-3a_A1_En
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: — Reorient or relocate the receiving antenna. — Increase the separation between the equipment and receiver. — Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. — Consult the dealer or an experienced radio/TV technician for help.
D8-10-1-2_A1_En
Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
1)
2)
3)
4)
5)
6)
7)
8)
9)
10)
Only use attachments/accessories specified by the manufacturer. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
Unplug this apparatus during lightning storms or when unused for long periods of time. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
D3-7-13-69_En
11)
12)
13)
14)
POWER-CORD CAUTION
Handle the power cord by the plug. Do not pull out the plug by tugging the cord and never touch the power cord when your hands are wet as this could cause a short circuit or electric shock. Do not place the unit, a piece of furniture, etc., on the power cord, or pinch the cord. Never make a knot in the cord or tie it with other cords. The power cords should be routed such that they are not likely to be stepped on. A damaged power cord can cause a fire or give you an electrical shock. Check the power cord once in a while. When you find it damaged, ask your nearest PIONEER authorized service center or your dealer for a replacement.
S002*_A1_En
Condensation
If the player is moved suddenly from a cold place into a warm room (in winter, for example) or if the temperature in the room in which the player is installed rises suddenly due to a heater, etc., water droplets (condensation) may form inside (on operating parts and the lens). When condensation is present, the player will not operate properly and playback is not possible. Let the player stand at room temperature for 1 or 2 hours with the power turned on (the time depends on the extent of condensation). The water droplets will dissipate and playback will become possible. Condensation can also occur in the summer if the player is exposed to the direct wind from an air-conditioner. If this happens, move the player to a different place.
S005_A1_En
CAUTION
The
STANDBY/ON switch on this unit will not completely shut off all power from the AC outlet. Since the power cord serves as the main disconnect device for the unit, you will need to unplug it from the AC outlet to shut down all power. Therefore, make sure the unit has been installed so that the power cord can be easily unplugged from the AC outlet in case of an accident. To avoid fire hazard, the power cord should also be unplugged from the AC outlet when left unused for a long period of time (for example, when on vacation).
D3-4-2-2-2a*_A1_En
This product is for general household purposes. Any failure due to use for other than household purposes (such as long-term use for business purposes in a restaurant or use in a car or ship) and which requires repair will be charged for even during the warranty period.
K041_A1_En
This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
D8-9-2-5_A1_En
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65. This equipment should be installed and operated keeping the radiator at least 20 cm or more away from person’s body (excluding extremities: hands, wrists, feet and ankles).
D8-9-2-7-2_A1_En
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment should be installed and operated keeping the radiator at least 20 cm or more away from person’s body (excluding extremities: hands, wrists, feet and ankles).
D8-9-2-7-4_A1_En
Radio wave caution
This unit uses a 2.4 GHz radio wave frequency, which is a band used by other wireless systems (Microwave ovens and Cordless phones, etc.). In this event noise appears in your television image, there is the possibility this unit (including products supported by this unit) is causing signal interference with the antenna input connector of your television, video, satellite tuner, etc. In this event, increase the distance between the antenna input connector and this unit (including products supported by this unit).
• Pioneer is not responsible for any malfunction of the compatible Pioneer product due to communication error/malfunctions associated with your network connection and/or your connected equipment. Please contact your Internet service provider or network device manufacturer.
• A separate contract with/payment to an Internet service provider is required to use the Internet.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
D8-9-10-1_A1_En
Cautions on 3D Viewing
If you should experience any fatigue or discomfort while viewing 3D images, stop viewing them.
Children, particularly those under 6, may be more prone to sensitivity, so guardians should watch for
any signs of fatigue or discomfort.
When viewing 3D images, rest periodically. Extended viewing of 3D images without rest periods could cause fatigue or discomfort.
WARNING: Handling the cord on this product or cords associated with accessories sold with the product may expose you to chemicals listed on proposition 65 known to the State of California and other governmental entities to cause cancer and birth defect or other reproductive harm.
D36-P5_B1_En
The Safety of Your Ears is in Your Hands
Get the most out of your equipment by playing it at a safe level – a level that lets the sound come through clearly without annoying blaring or distortion and, most importantly, without affecting your sensitive hearing. Sound can be deceiving. Over time, your hearing “comfort level” adapts to higher volumes of sound, so what sounds “normal” can actually be loud and harmful to your hearing. Guard against this by setting your equipment at a safe level BEFORE your hearing adapts.
ESTABLISH A SAFE LEVEL:
• Set your volume control at a low setting.
• Slowly increase the sound until you can hear it comfortably and clearly, without distortion.
• Once you have established a comfortable sound level, set the dial and leave it there.
BE SURE TO OBSERVE THE FOLLOWING GUIDELINES:
• Do not turn up the volume so high that you can’t hear what’s around you.
• Use caution or temporarily discontinue use in potentially hazardous situations.
• Do not use headphones while operating a motorized vehicle; the use of headphones may create a traffic hazard and is illegal in many areas.
S001a_A1_En
Contents
01 Before you start
What’s in the box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Putting the batteries in the remote control. . . . . . . . . . . . .7
Software Update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
About operation of this player from a mobile device
(iPod, iPhone, iPad etc.). . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Types of discs/files that can be played . . . . . . . . . . . . . . . . . . 8
Playable discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Playable files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Part Names and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
02 Connecting up
Connecting using an HDMI cable. . . . . . . . . . . . . . . . . . . . . 16
About HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
About Control Function with HDMI . . . . . . . . . . . . . . . . . . 17
Connecting a TV. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Connecting an AV receiver or amplifier. . . . . . . . . . . . . . . 18
Connecting audio cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Connecting an AV receiver or amplifier using
an coaxial digital audio cable . . . . . . . . . . . . . . . . . . . . . . . 19
Connecting components to the USB port . . . . . . . . . . . . . . 19
About USB devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Connecting the USB device . . . . . . . . . . . . . . . . . . . . . . . . 19
Connecting to the network through LAN interface . . . . . . . 20
Connecting with a LAN cable (wired LAN) . . . . . . . . . . . .20
Connecting to a wireless LAN . . . . . . . . . . . . . . . . . . . . . .20
Connecting the power cord . . . . . . . . . . . . . . . . . . . . . . . . . .20
03 Getting Started
Making settings using the Setup Navigator menu . . . . . . . 21
04 Playback
Playing discs or files. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Quick view (Quick view with audio) . . . . . . . . . . . . . . . . . . 22
Forward and reverse scanning . . . . . . . . . . . . . . . . . . . . . . 23
Playing specific chapters, tracks or files . . . . . . . . . . . . . . 23
Skipping content . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
To return to a position a short while ago. . . . . . . . . . . . . .23
To advance to a position slightly ahead. . . . . . . . . . . . . . .23
Playing in slow motion . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Step forward and step reverse . . . . . . . . . . . . . . . . . . . . . . 23
Playing a specific section within a title or track
repeatedly (A-B Repeat) . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Playing repeatedly (Repeat Play) . . . . . . . . . . . . . . . . . . . . 23
Playing in the desired order (Programmed Play) . . . . . . . 24
Making bookmarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Playing photos as slideshows. . . . . . . . . . . . . . . . . . . . . . . 24
Switching the camera angles . . . . . . . . . . . . . . . . . . . . . . . 24
Switching the subtitles . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Moving subtitles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Switching the audio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Switching the CD/SACD playback area. . . . . . . . . . . . . . . 25
Displaying the disc information . . . . . . . . . . . . . . . . . . . . . 25
Enjoying BONUSVIEW or BD-LIVE . . . . . . . . . . . . . . . . . . .26
Playback functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Using the FUNCTION menu . . . . . . . . . . . . . . . . . . . . . . . . .28
Playing from a specific time (Time Search). . . . . . . . . . . . 29
Playing a specific title, chapter, track or file (Search) . . . 29 Playing specified range of discs, titles or
chapter (track/file) in random order. . . . . . . . . . . . . . . . . . 29
Continuing playback from a specified position
(Continued Viewing Playback). . . . . . . . . . . . . . . . . . . . . . . . 29
05 Playback from Home Media Gallery
About Home Media Gallery . . . . . . . . . . . . . . . . . . . . . . . . . . 30
About network playback . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Playback file on the network . . . . . . . . . . . . . . . . . . . . . . . . . 31
Disc/USB playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Playing back image files . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Playing in the desired order (Playlist). . . . . . . . . . . . . . . . . . 32
Adding tracks/files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Playing the Playlist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Deleting tracks/files from the Playlist . . . . . . . . . . . . . . . . 32
Connecting by Miracast
About Wi-Fi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Use the unit’s Miracast/Wi-Fi Direct functions . . . . . . . . 33
Display the Miracast/Wi-Fi Direct mode screen. . . . . . . . 33
Connecting by Miracast . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Connect to device not compatible with Miracast/Wi-Fi
Direct . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Connecting by WPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Change SSID and password. . . . . . . . . . . . . . . . . . . . . . . . 34
Canceling the Miracast/Wi-Fi Direct connection . . . . . . 35
Playing a mobile device’s photos, music or video files. . . . 35
06 Playing the web contents
Available web contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Playing the items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
07 Advanced settings
Changing the settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Operating the Initial Setup screen. . . . . . . . . . . . . . . . . . . 37
Software updating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Restoring all the settings to the factory
default settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Wireless network connection . . . . . . . . . . . . . . . . . . . . . . . . 44
Wireless network setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
WPS setup (Wi-Fi Protected Setup) . . . . . . . . . . . . . . . . . . . 45
WPS connection setting . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
About how digital audio formats are output . . . . . . . . . . . . 46
Language Code Table and Country/Area Code Table . . . . . 47
Language Code Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Country/Area Code Table . . . . . . . . . . . . . . . . . . . . . . . . . . 47
08 Additional information
Cautions on use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Moving the player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Place of installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Turn the power off when not using the player . . . . . . . . . 48
Condensation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Cleaning the player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Caution for when the unit is installed in a rack
with a glass door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Cleaning the pickup lens . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Handling discs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Control function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Wireless LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Others. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Glossary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
TM/
Wi-Fi DirectTM. . . . . . . . . . . . . . 33
6
En
Chapter 1
Before you start
What’s in the box
• Remote control x 1
• AAA 700 size manganese batteries x 2
•Power cord
•Warranty card
• Software license notice
• Operating instructions (this document)
Putting the batteries in the remote control
The batteries included with the player have been provided to allow you to check product operation and may not last long. We recommend using alkaline batteries that have a longer life.
WARNING
• Do not use or store batteries in direct sunlight or other excessively hot place, such as inside a car or near a heater. This can cause batteries to leak, overheat, explode or catch fire. It can also reduce the life or performance of batteries.
Caution
• Do not use a new battery together with an old one.
• When loading the batteries into the remote control, set them in the proper direction, as indicated by the polarity marks ( and ).
• When inserting the batteries, make sure not to damage the springs on the battery’s  terminals. This can cause batteries to leak or overheat.
• Do not heat batteries, disassemble them, or throw them into flames or water.
• Batteries may have different voltages, even if they look similar. Do not use different kinds of batteries together.
• To prevent leakage of battery fluid, remove the batteries if you do not plan to use the remote control for a long period of time (1 month or more). If the fluid should leak, wipe it carefully off the inside of the case, then insert new batteries. If a battery should leak and the fluid should get on your skin, flush it off with large quantities of water.
• When disposing of used batteries, please comply with governmental regulations or environmental public institution’s rules that apply in your country/area.
1 Open the rear cover.
2 Insert (2 x AAA 700 size) batteries that are supplied.
Insert first from the side.
3 Close the rear cover.
Close securely (a click should be heard).
About the function for restricting access to harmful information on the Internet
• This unit is equipped with a function for restricting viewing of web contents, etc., you do not want your children or others to see.
• To use this restriction function, change the Internet settings (page 40).
Software Update
Product information on this player is provided on the Pioneer website. Check this website for update and service information on your Blu-ray disc player.
http://www.pioneerelectronics.com
About operation of this player from a mobile device (iPod, iPhone, iPad etc.)
The player can be controlled from a mobile device by installing the special application onto the mobile device.
For details, see the product information on the Pioneer website.
This special application may be changed or discontinued without notice.
01
7
En
Types of discs/files that can be played
01
Playable discs
Discs with the logo marks below indicated on the disc label, package or jacket can be played.
Caution
• Only the discs that have been finalized can be played.
Disc type Logo
BD-ROM 
2
BD
BD-R
BD-RE 
DVD-ROM 
BDMV BDAV

Application format
DVD-
Video
DVD VR
CD-DA
DTS-CD
DATA-
DISC
1
DVD
CD
1. Discs on which video, image or audio files are recorded.
2. Including dual-layered discs.
3. Finalize them bef ore playing them on this player.
4. DVD-R for Authoring discs (3.95 GB and 4.7 GB) cannot be played.
5. Including the AVCHD form at.
6. Including the AVCREC format.
7. Version 1.0 DVD-RW discs can not be played.
8. Including Video CDs.
2,3,4
DVD-R
3,7
DVD-RW
2,3
DVD+R
3
DVD+RW
CD-DA
8
(Audio CD)
3
CD-R
3
CD-RW
CD-ROM 
• “Blu-ray Disc”, “Blu-ray” and “Blu-ray Disc” logo are trademarks of Blu-ray Disc Association.
8
En
5
5





6
6
 
 
is a trademark of DVD Format /Logo Licensing
Corporation.
Discs that cannot be played
• HD DVDs
•DVD-RAM discs
It is possible that some discs other than the ones listed above may not be playable either.
Note
• Some discs cannot be played, even if one of the logo marks on the previous page is indicated.
• To play 8 cm discs, set the disc in the 8 cm disc depression in the center of the disc tray. No adapter is necessary. 8 cm BD-ROMs cannot be played.
About playback of unauthorized copies
Cinavia Notice
This product uses Cinavia technology to limit the use of unauthorized copies of some commercially-produced film and videos and their soundtracks. When a prohibited use of an unauthorized copy is detected, a message will be displayed and playback or copying will be interrupted.
More information about Cinavia technology is provided at the Cinavia Online Consumer Information Center at http://www.cinavia.com. To request additional information about Cinavia by mail, send a postcard with your mailing address to: Cinavia Consumer Information Center, P.O. Box 86851, San Diego, CA, 92138, USA.
Copyright 2004-2010 Verance Corporation. Cinavia™ is a Verance Corporation trademark. Protected by U.S. Patent 7,369,677 and worldwide patents issued and pending under license from Verance Corporation. All rights reserved.
About copyright protection
Copyright protection technology is used for some Blu-ray
TM
Discs
, DVDs and contents played over the Internet or other networks. Copyright protection technology restricts playback and analog output. Due to updates in copyright protection provisions, the restrictions may differ depending on the date this product was purchased. Furthermore, the restrictions may be updated when the software is updated after purchase.
About audio formats
The following audio formats are supported on this player:
•Dolby TrueHD
•Dolby Digital Plus
•Dolby Digital
•DSD
•DTS-HD Master Audio
• DTS-HD High Resolution Audio
• DTS Digital Surround
•MPEG audio (AAC)
• Linear PCM
To enjoy the surround sound of Dolby TrueHD, Dolby Digital Plus, DSD, DTS-HD Master Audio and DTS-HD High Resolution Audio, it is recommended to connect the player to an AV receiver or amplifier compatible with these audio formats using an HDMI cable. After loading a BD containing sound in one of these audio formats, select the audio format on the menu screen.
Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.
Manufactured under license under U.S. Patent Nos: 5,956,674; 5,974,380; 6,226,616; 6,487,535; 7,392,195; 7,272,567; 7,333,929; 7,212,872 & other U.S. and worldwide patents issued & pending. DTS-HD, the Symbol, & DTS-HD and the Symbol together are registered trademarks & DTS­HD Master Audio | Essential is a trademark of DTS, Inc. Product includes software. © DTS, Inc. All Rights Reserved.
Playing BDs
• BDs (BDMV) compatible with the formats below can be played.
– Blu-ray Disc Read-Only (ROM) Format Version 2
– Blu-ray Disc Recordable (R) Format Version 2
– Blu-ray Disc Rewritable (RE) Format Version 3
This player supports BD-ROM Profile 5.
“Blu-ray 3D” and “Blu-ray 3D” logo are trademarks of Blu-ray Disc Association.
BONUSVIEW functions such as playback of secondary video (Picture-in-Picture) and secondary audio can be used. The data used with the BONUSVIEW functions (the secondary video (Picture-in-Picture) and secondary audio data) may be stored in the storage. For details on secondary video and secondary audio playback, refer to the disc’s instructions.
“BONUSVIEW” is trademark of Blu-ray Disc Association.
01
9
En
01
BD-LIVE functions such as downloading movie trailers or additional audio and subtitle languages and playing on-line games can be enjoyed over the Internet. The data downloaded with the BD-LIVE function (trailers, etc.) is stored in the storage. Refer to the disc’s instructions for details about BD-LIVE functions.
“BD-LIVE” logo is trademark of Blu-ray Disc Association.
With BD-ROMs, it is possible to use BD-J (Java) applications to create highly interactive titles, for example including games.
Oracle and Java are registered trademarks of Oracle and/or its affiliates. Other names may be trademarks of their respective owners.
• BDs (BDAV) compatible with the formats below can be played.
– Blu-ray Disc Recordable (R) Format Version 1
– Blu-ray Disc Rewritable (RE) Format Version 2
Playing DVDs
This label indicates playback compatibility with DVD-RW discs recorded in VR format (Video Recording format). However, for discs recorded with a record-only-once encrypted program, playback can only be achieved using a CPRM compatible device.
The AVCHD is a high definition (HD) digital video camera recorder format recording high-definition onto certain media by using highly efficient codec technologies.
About region numbers
Blu-ray Disc Player and BD-ROM or DVD-Video discs are assigned region numbers according to the region in which they are sold.
This player’s region numbers are:
•BD-ROM: A
• DVD-Video: 1
Discs not including these numbers cannot be played. Discs playable on this player are as shown below.
• BDs: A (including A) and ALL
• DVDs: 1 (including 1) and ALL
Playing CDs
Regarding copy protected CDs: This player is designed to conform to the specifications of the Audio CD format. This player does not support the playback or function of discs that do not conform to these specifications.
DualDisc playback
A DualDisc is a two-sided disc, one side of which contains DVD content — video, audio, etc. — while the other side contains non-DVD content such as digital audio material.
The DVD side of a DualDisc can be played on this player.
The non-DVD, audio side of the disc is not compatible with this player.
It is possible that when loading or ejecting a DualDisc, the opposite side to that being played will be scratched. Scratched discs may not be playable.
For more detailed information on the DualDisc specification, please refer to the disc manufacturer or disc retailer.
Playing discs created on computers or BD/DVD recorders
• It may not be possible to play discs recorded using a computer due to the application settings or computer’s environment settings. Record discs in a format playable on this player. For details, contact the dealer.
• It may not be possible to play discs recorded using a computer or a BD/DVD recorder, if burn quality is not good due to characteristics of the di sc, scratches, dirt on the disc, dirt on the recorder’s lens, etc.
“AVCHD” and the “AVCHD” logo are trademarks of Panasonic Corporation and Sony Corporation.
10
En
About video, audio, and image files
*
*
*
*
Root
01 Folder
XX Folder
Folder
001.jpg/001.mp3
xxx.jpg/xxx.mp3
001.jpg/001.mp3
xxx.jpg/xxx.mp3
001.jpg/001.mp3
xxx.jpg/xxx.mp3
001.jpg/001.mp3
xxx.jpg/xxx.mp3
and folders
Audio and image files can be played on this player when the folders on the disc or USB device are created as described below.
Example of folder structure:
* The number of folders and files within a single folder (including the root directory) is limited to a maximum of
256. Also, keep the number of folder layers to a maximum of 5.
Note
• The file and folder names displayed on this player may differ from those displayed on a computer.
Playable files
Video, image and audio files recorded on BDs, DVDs, CDs or USB devices can be played.
Supported video file formats
•DivX Plus HD
DivX Certified (H.264/MKV) video up to 1080p HD including premium content.
ABOUT DIVX VIDEO: DivX created by DivX, LLC, a subsidiary of Rovi Corporation.
This is an official DivX Certified DivX video. Visit divx.com for more information and software tools to convert your files into DivX videos.
®
to play DivX® and DivX PlusTM HD
®
is a digital video format
®
device that plays
ABOUT DIVX VIDEO-ON-DEMAND: This DivX
®
Certified
device must be registered in order to play purchased DivX Video-on-Demand (VOD) movies. To obtain your registration code, locate the DivX VOD section in your device setup menu. Go to vod.divx.com for more information on how to complete your registration.
®
DivX
, DivX Certified®, DivX PlusTM HD and associated logos are trademarks of Rovi Corporation or its subsidiaries and are used under license.
Note
•This DivX
®
Certified device must be registered in order to play DivX Video-on-Demand (VOD) content. First generate the DivX VOD registration code for your device and submit it during the registration process. Important: DivX VOD content is protected by a DivX DRM (Digital Rights Management) system that restricts playback to registered DivX Certified devices. If you try to play DivX VOD content not authorized for your device, the message Authorization Error will be displayed and your content will not be played. Learn more at www.divx.com/vod.
– This player’s DivX VOD registration code can be
checked at HOME MENU Initial Setup
Playback DivX
®
VOD DRM Registration
Code (page 40).
– The number of views is restricted for some DivX
VOD files. When such files are played on this player, the remaining number of views is displayed. Files for which the remaining number of views has reached 0 cannot be played (This DivX rental has expired is displayed). Files for which the number of views is not restricted can be played as many times as you like (the remaining number of views is not displayed).
• YouTube
TM
YouTube
is a trademark of Google inc.
01
11
En
Table of Playable Files
01
Playable files
(Extensions)
MP3 (.mp3)
2
WMA (.wma)
3
AAC (.m4a)
WAV (.wav)
FLAC (.flac)
Monkey’s Audio (.ape)
JPEG (.jpg/.jpeg)
MPO (.mpo)
PNG (.png)
GIF (.gif)
DivX (.avi/.divx/.mkv)
MP4 (.mp4)
WMV (.wmv)
AVI (.avi)
3GP (.3gp)
Playable media
BD-R/RE/-R DL/
RE DL/-R LTH,
DVD-R/RW/-R DL/
+R/+RW/+R DL,
CD-R/RW






Maximum resolution: 4 000 x 3 000 pixels
3D photo image







USB devices
1
Network
Sampling frequencies: Up to 48 kHz
Bit rate: Up to 320 kbps
Audio type: MPEG-1 Audio Layer 3
Sampling frequencies: Up to 48 kHz
Bit rate: Up to 192 kbps
Audio type: WMA version 9
Sampling frequencies: Up to 96 kHz
Bit rate: Up to 192 kbps
Audio type: MPEG4-AAC
Sampling frequencies: Up to 192 kHz
Quantization bitrate: 16 bit, 24 bit
Channel: 2ch
Sampling frequencies: Up to 192 kHz
Quantization bitrate: 16 bit, 24 bit
Channel: Multi channel
Sampling frequencies: Up to 192 kHz
Quantization bitrate: 16 bit
Channel: 2ch
Maximum resolution: 2 048 x 1 024 pixel
Animated PNG files are not supported.
Maximum resolution: 2 048 x 1 024 pixel
Animated GIF files are not supported.
Rotate is not supported.
Supported versions: Through DivX
Maximum resolution:
Up to 1 920 x 1 080 (DivX
Up to 1 280 x 720 (MKV)
Maximum resolution: Up to 1 920 x 1 080
Video: MPEG4, MPEG-4 AVC (level 4.1)
Audio: AAC, MP3
Maximum resolution: Up to 1 280 x 720
Video: WMV9, WMV9AP (VC-1)
Audio: WMA
Maximum resolution: Up to 1 920 x 1 080
Video: MPEG4
Audio: MP3, AAC
Video: H.263, MPEG4, H.264
Audio: MPEG-4 AAC
File specifications
®
PLUS HD)
®
PLUS HD
12
En
Playable media
Playable files
(Extensions)
FLV (.flv)
1. This unit supports FAT16, FAT32 and NTFS file systems.
2. WMA Pro, Lossless and Voice are not supported.
3. Apple lossless encoding is not supported.
BD-R/RE/-R DL/
RE DL/-R LTH,
DVD-R/RW/-R DL/
+R/+RW/+R DL,
CD-R/RW

USB devices
1
Network
File specifications
Video: Sorenson H.263 (FLV1), VP6 (FLV4),
H.264
Audio: MP3, AAC
Note
• Depending on the file structure, the server capacity and the network environment, it may not be possible to play certain files, even for files indicated on the table of playable files above.
• With wireless LAN connections, depending on the usage environment (radio interference, etc.), the picture or sound may be interrupted when playing high picture quality video files (such as files with HD quality) or high sound quality music files (such as 192 kHz/24 bit WAV files) due to the large amount of data that must be transferred.
• Files protected by DRM (Digital Rights Management) cannot be played (not including DivX VOD files).
• AVCHD contents cannot be played via LAN.
01
13
En
Part Names and Functions
14
9
5
4
10
16
17
6
7
30
15
1
3
21
12
13
11
28
29
22
19
24
25
27
18
20
8
2
23
26
01
Remote Control
9 – (page 23)
10 STOP – (page 22)
11 REV – (page 23)
12 TOP MENU – Press to display the top menu of the
BD-ROM or DVD-Video.
13 /// – Use to select items, change settings and
move the cursor.
ENTER – Press to execute the selected item or enter a setting that has been changed, etc.
14 HOME MENU – (page 37)
15 Color buttons – Use these to navigate BD-ROM
menus.
PROGRAM – (page 24)
BOOK MARK – (page 24)
ZOOM – (page 24)
INDEX – (page 24)
1 STANDBY/ON – Press to turn the power on and
off.
2CONTINUED – Use to continue playback from a
specified position. (page 29)
3 AUDIO – (page 25)
4 SUBTITLE – (page 25)
5CD/SACD – For hybrid discs, press to switch between
the CD and SACD layers. (page 25)
6 REPEAT – (page 23)
7A-B – (page 23)
8 YouTube – Use to play the video on YouTube.
(page 36)
14
En
16 Number buttons – Use these to select and play the
title/chapter/track you want to view or listen to and to select items from menus.
17 CLEAR – Press to clear the numeric number, etc.
18 OPEN/CLOSE – Press to open and close the disc
tray.
19 DISPLAY – (page 25)
20 Miracast – Display the Miracast/Wi-Fi Direct mode
screen. (page 33)
21 FL DIMMER – Each time this is pressed, the
brightness of the front panel display switches (in 4 levels).
22 SHORT SKIP – Press during playback to forward to a position 30 seconds later. (page 23)
23 REPLAY – Press during playback to return to a position 10 seconds earlier. (page 23)
24 HDMI – Use to switch the resolution of the video
signals output from the HDMI OUT terminal (page 38).
25 // – (page 23)
26 – (page 22)
27 FWD – (page 23)
28 POP UP MENU/MENU – Press to display the
BD-ROM or DVD-Video menus.
29 RETURN – Press to return to the previous
1 2 3 54 6 7 8
9
2
1
4 5 63
screen.
Front Panel
30 FUNCTION – (page 28)
01
1 STANDBY/ON – Press to turn the power on and
off.
2Disc tray
3 Front panel display
4 Reset button – If the power cannot be turned off (set
to standby), use a thin rod to press this button. The unit restarts, at which point it is again operable.
5 Remote control sensor – Point the remote control to
this, then operate it within approximately 7 m.
The player may have trouble capturing remote control signals if there is a fluorescent light nearby. If this happens, move the player away from the fluorescent light.
Rear Panel
1 DIGITAL OUT (COAXIAL) terminal – (page 19)
2 AUDIO OUT terminals – (page 19)
3 HDMI OUT terminal – (page 16)
6 OPEN/CLOSE – Press to open and close the disc
tray.
7 – Press to stop playback.
8 USB port – (page 19)
9 – Press to start playback.
4 LAN (10/100) terminal – (page 20)
5 USB port – (page 19)
6AC IN – (page 20)
15
En
Chapter 2
02
Connecting up
Be sure to turn off the power and unplug the power cord from the power outlet whenever making or changing connections.
After connecting, make the settings at the Setup Navigator or Initial Setup menu according to the type of cable connected (page 21).
Also refer to the operating instructions for the device being connected.
“x.v.Color” is a promotion name given to the products that have the capability to realize a wide-gamut color space based on the international standard specifications defined as xvYCC.
Connecting using an HDMI cable
The audio and video signals can be transferred to HDMI­compatible devices as digital signals with no loss of sound or video quality.
Note
• Make the settings at the Setup Navigator menu according to the connected HDMI-compatible device (page 21).
• 1080p video signals may not be output, depending on the HDMI cable being used.
About HDMI
This player incorporates the High-Definition Multimedia Interface (HDMI
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing, LLC in the United States and other countries.
The player supports Deep Color. The conventional players can transmit a video signal with 8 bit color depth in the YCbCr 4:4:4 or RGB format; the players supporting Deep Color can transmit a video signal with a color bit depth of greater than 8 bits per color component. Subtle color gradations can be reproduced when this player is connected to a TV that supports Deep Color.
This product is compatible with “x.v.Color” that have the capability to realize a wide-gamut color space based on the xvYCC specifications. Playing video signals conforming to “xvYCC” standards on this player when this player is connected to an “x.v.Color”-compatible TV, etc., expands color reproduction capabilities, allowing natural colors to be
16
reproduced more faithfully than ever.
En
®
) technology.
“x.v.Color” and are trademarks of Sony Corporation.
Playable audio signals through the HDMI OUT terminal
•Dolby TrueHD
•Dolby Digital Plus
•Dolby Digital
•DTS-HD Master Audio
• DTS-HD High Resolution Audio
• DTS Digital Surround
• Linear PCM Linear PCM audio signals meeting the following
conditions can be output:
– Sampling frequency: 32 kHz to 192 kHz
– Number of channels: Up to 8 (up to 6 for a 192 kHz
sampling frequency)
•DSD audio
• AAC
When connected to a DVI device
It is not possible to connect DVI devices (computer displays, for example) that are not compatible with HDCP. HDCP is a specification to
protect audiovisual content across the DVI/HDMI interface.
• No audio signals are output.
• This player is designed for connection with HDMI­compatible devices. When connected to a DVI device, it may not operate properly depending on the DVI device.
About Control Function with HDMI
The functions work when a control function with HDMI­compatible Pioneer TV or AV system (AV receiver or amplifier, etc.) is connected to the player using an HDMI cable.
Also refer to the operating instructions for the TV and AV system (AV receiver or amplifier, etc.).
To use the control function with HDMI
• The control function with HDMI operates when control function with HDMI is set to On for all devices connected with HDMI cables.
• Once the connections and the settings of all the devices are finished, be sure to check that the player’s picture is output to the TV. (Also check after changing the connected devices and reconnecting HDMI cables.) The control function with HDMI may not operate properly if the player’s picture is not properly output to the TV.
• Use High Speed HDMI control function with HDMI. The control function with HDMI may not operate properly if other HDMI cables are used.
• For some models, the control function with HDMI may be referred to as “KURO LINK” or “HDMI Control”.
• The control function with HDMI does not work with devices of other brands, even if this player is connected with an HDMI cable.
What the control function with HDMI can do
• Operating the player with the TV’s remote control.
Such player operations as starting and stopping playback and displaying the menus can be performed from the TV.
• The player’s playback picture is displayed on the TV’s screen. (Auto-select function)
The input switches automatically on the TV and AV system (AV receiver or amplifier, etc.) when playback is started on the player or the HOME MENU is displayed. When the input is switched, the playback picture, the HOME MENU appears on the TV.
• The power of the TV and the player turns on and off automatically. (Simultaneous power function)
When playback on the player is started or the HOME MENU is displayed, if the TV’s power was off, its power turns on automatically. When the TV’s power is turned off, the player’s power automatically turns off.
®/TM
Cables when using the
Sound Retriever Link
About Sound Retriever Link
Sound Retriever Link is a sound quality correction control technology that automatically adjusts the compressed sound quality for the connected AV receiver using HDMI control function.
Sound Retriever Link function allows you to enjoy higher quality audio by setting the connected AV receiver’s Sound Retriever function automatically.
Sound Retriever Link function on this player works exclusively with the following situations.
• When playing via a network or playing PC contents stored on a USB device.
• The Pioneer AV receiver compatible with Sound Retriever Link function is connected to this player through an HDMI cable and the player’s setting is set as shown below (page 39).
Control: On
• Also refer to the instructions of the AV receiver.
• See Pioneer website about AV receivers compatible with Sound Retriever Link function.
Caution
• Connect the player directly to the Pioneer AV receiver compatible with Sound Retriever Link function. Interrupting a direct connection with an amplifier or AV converter (such as an HDMI switch) can cause malfunction.
Stream Smoother Link
About Stream Smoother Link
Stream Smoother Link is a function that improves picture quality of network video contents using the control function with HDMI. Stream Smoother Link function allows you to enjoy a high quality picture with less noise by setting the connected AV receiver’s Stream Smoother function automatically.
Stream Smoother Link function on this player works exclusively with the following situations.
• When playing a video distribution service on a network or PC contents stored on a medium.
• The Pioneer AV receiver with Stream Smoother Link function is connected to this player through an HDMI cable and the player’s setting is set as shown below (page 39). Also refer to the instructions for the AV receiver.
Control: On
See Pioneer website about AV receivers compatible with Stream Smoother Link function.
Caution
• Connect the player directly to the Pioneer AV receiver compatible with Stream Smoother Link function. Interrupting a direct connection with an amplifier or AV converter (such as HDMI switch) can cause malfunction.
02
17
En
Connecting a TV
Rear panel
TV
Match the direction of the plug to the terminal and insert straig ht.
To HDMI
input terminal
HDMI cable
(commercially
available)
It is also possible to connect to an AV receiver or amplifier using an HDMI cable.
Direction of signal flow
Rear panel
To HDMI
input terminal
From HDMI
output
terminal
AV receiver
or amplifier
To HDMI input
terminal
TV
HDMI cable
(commercially
available)
Match the direction
of the plug to the
terminal and insert
straight.
Direction of signal flow
HDMI cable
(commerciall y
available)
02
See Connecting an AV receiver or amplifier on page 18 to connect an AV receiver or amplifier using an HDMI cable.
Caution
• Hold the plug when connecting and disconnecting the cable.
• Placing a load on the plug could result in faulty contact and no video signals being output.
Connecting an AV receiver or amplifier
Connect to an AV receiver or amplifier in order to enjoy the surround sound of Dolby TrueHD, Dolby Digital Plus, Dolby Digital, DTS-HD Master Audio, DTS-HD High Resolution Audio, DTS Digital Surround, LPCM, AAC or DSD. For instructions on connecting the TV and speakers to the AV receiver or amplifier, refer to the operating instructions for AV receiver or amplifier.
Caution
• Hold the plug when connecting and disconnecting the cable.
• Placing a load on the plug could result in faulty contact and no video signals being output.
18
En
Connecting audio
UT
AV receiver or amplifier
Rear panel
Direction of
signal flow
White
Red
To audio input
terminals
Audio cable
(commercially
available)
Coaxial digital audio cable (commercially available)
To coaxial digital audio input terminal
2-channel
analog audio
can also be connected.
USB flash drive
Player’s front panel
Hard disk, etc.
USB cable
(commercially
available)
USB flash drive
Rear panel
Hard disk, etc.
USB cable
(commercially
available)
cables
Connecting an AV receiver or amplifier using an coaxial digital audio cable
Connecting components to the USB port
About USB devices
The USB devices that can be connected to the player are as shown below.
• USB 2.0-compatible USB flash drive (capacity of 1 GB or greater, 2 GB or greater recommended) or HDD (capacity 2 TB or less)
• File system: FAT16, FAT32 or NTFS
Connecting the USB device
Caution
• Be sure to turn the player’s power off before connecting or disconnecting USB devices.
• When using an external hard disk as the external storage device, be sure to turn on the hard disk’s power before turning on the player’s power.
• If the USB device is write-protected, be sure to disable the write-protection.
• When connecting the USB cable, hold onto the plug, set the plug in the proper direction for the port and insert it horizontally.
• Placing excessive loads on the plug may result in poor contact, making it impossible to write data on the USB device.
• When a USB device is connected and the player’s power is turned on, do not unplug the power cord.
02
• Devices formatted with a file system other than the above cannot be used.
• USB devices may not be recognized if they contain multiple partitions.
• Some USB devices may not operate with this player.
• Operation of USB devices is not guaranteed.
Note
Note
• Devices may not work if connected to the USB port via
a memory card reader or USB hub.
• Use a USB cable with a length of 2 meters or less.
19
En
Connecting to the
WAN
321
LAN
LAN cable
(commercially available)
Router
Internet
ModemLAN cable
(commercially
available)
Computer
Rear panel
WAN
Router
Internet
Modem
Computer
Rear panel
Power cord
(included)
To wall outlet
02
network through LAN interface
By connecting this player to the network via the LAN terminal or a wireless LAN, you can play image, audio and video files stored on the components on the network, including your computer, using HOME MEDIA GALLERY inputs.
Turn on the DHCP server function of your router. In case your router does not have the built-in DHCP server function, it is necessary to set up the network manually. For details, see Setting the IP address on page 41 .
Note
• Refer to the operation manual of the equipment you have as the connected equipment and connection method may differ depending on your Internet environment.
• When using a broadband Internet connection, a contract with an Internet service provider is required. For more details, contact your nearest Internet service provider.
• Please note that Pioneer will accept no responsibility whatsoever for communications errors or problems related to the user's network connection environment or connected devices. Contact your provider or the manufacturer of your connected devices.
Connecting with a LAN cable (wired LAN)
Connect the LAN terminal on this receiver to the LAN terminal on your router (with or without the built-in DHCP server function) with a straight LAN cable (CAT 5 or higher).
LAN terminal specifications
LAN terminal: Ethernet jack (10BASE-T/100BASE-TX)
Connecting to a wireless LAN
Manual settings must be made to connect to a wireless LAN. For details, see Wireless network connection on page 44.
Connecting the power cord
Connect the power cord after all the connections between devices have been completed.
20
En
Chapter 3
Getting Started
03
Making settings using the Setup Navigator menu
Be sure to perform these settings when using the player in the following situations.
• When you use the player for the first time.
•After Initial Setup format.
Caution
• Before turning on the power, check that the connections between the player and other devices are correct. Also, turn on the power of the devices connected to the player before turning on the player’s power.
• When using a Pioneer TV or front projector compatible with the Control function, set Control to On on the connected device before turning on the player’s power.
1 Turn on the TV’s power and switch the input.
See the TV’s operating instructions for the details of operating the TV.
2 Turn on the player’s power.
Press STANDBY/ON. Check that the Setup Navigator menu is displayed.
If the Setup Navigator menu is not displayed
Press HOME MENU to display the Home Menu, select Initial Setup Setup Navigator Start, then press ENTER.
3 Start Setup Navigator.
Press ENTER.
Setup Navigator starts.
4 Select the OSD language.
Use / to select, then press ENTER.
When a Pioneer TV that is compatible with Control function is connected to this player’s HDMI OUT terminal, language settings are imported from the Pioneer TV’s language settings before Setup Navigator begins.
5 Select the appropriate output resolution for the connected TV. Use / to select, then press ENTER.
6 Select the appropriate aspect for the connected TV. Use / to select, then press ENTER.
7 Close the Setup Navigator menu.
Press ENTER.
Setup Navigator finishes and the setting is stored.
• Press RETURN to go back to the previous
screen.
21
En
Chapter 4
04
Playback
Playing discs or files
This section describes the player’s main operations.
For the types of discs and files that can be played, see page 8. Video, image and audio files recorded on discs are played with the Home Media Gallery (page 30).
1 Press  STANDBY/ON to turn on the power.
Turn the TV’s power on and switch its input beforehand.
2 Press OPEN/CLOSE to open the disc tray and load the disc.
Note
• Load the disc with the printed side facing up.
• Several dozen seconds are required to read the disc. Once reading is completed, the type of disc is displayed on the player’s front panel display.
• When a BD with usage restrictions set by a BD recorder is loaded, the PIN code input screen appears. In this case, input your PIN code.
3 Press to play the disc.
• To pause, press during playback.
• To stop, press STOP during playback.
Note
• Some discs start playing automatically when the disc tray is closed.
• BD-ROM/DVD-Video discs have parental lock features. Input the password registered in the player’s settings to unlock the parental lock. For details, see page 42.
• Some BD-R/-RE discs have playback protection. To cancel the protection, input the password set for the disc.
• If the picture and sound are not properly output, Troubleshooting on page 50.
If the disc menu is displayed
For some discs, the disc menu is displayed automatically when playback starts. The contents of the disc menu and the way to operate depend on the disc.
Resuming playback from where it was stopped (resume playback function)
• When STOP is pressed during playback, the point at which the disc stopped is stored in the memory. When is pressed after that, playback resumes from that point.
• To cancel the resume playback function, press
22
STOP while playback is stopped.
En
Note
• The resume playback function is canceled automatically in the following cases:
– When the disc tray is opened.
– When the file list window is switched.
– When the power is turned off. (For BDs and DVDs
this does not cancel the resume playback function.)
– When it entered the Miracast / Wi-Fi Direct Mode
screen. (page 33)
• When you want to continue playback from a position you specify to be played next time, see Playing
specified range of discs, titles or chapter (track/file) in random order on page 29.
• The resume playback function cannot be used for some discs.
Quick view (Quick view with audio)
Audio is being output while the video images are played back at about 1.5 times the normal speed.
Press while playing back BD or DVD.
•If  is pressed during quick view, it will switch to fast forward.
To return to normal playback
• Press .
Note
• You cannot pause during quick view. Please pause after returning to normal playback.
• As for the tone during quick view, the output comes via PCM regardless of the configuration of the main body of the device.
• It is not possible to switch the audio during quick view.
• Depending on the audio format, such as Dolby TrueHD and DTS-HD Master Audio,there might be no sound output during fast-forward.
• For the output conditions of each voice, please refer to About how digital audio formats are output on page 46.
Forward and reverse scanning
During playback or quick view, press REV or FWD.
• The scanning speed switches each time the button is pressed. The speed steps depend on the disc or file (the speed is displayed on the TV screen).
To resume normal playback
Press .
Playing specific chapters, tracks or files
During playback, input the number of the chapter/track/file you want to select.
• Use the number buttons (0 to 9) to input the number, then press ENTER.
• Press CLEAR to clear the values you have input.
Skipping content
During playback, press or .
• When is pressed, the playback skips ahead to the beginning of the next chapter/track/file.
• When is pressed while a video or audio file is playing, the playback skips back to the beginning of the currently playing chapter/track/file. Press twice to skip back to the beginning of the previous chapter/ track/file.
• When is pressed while an image file is playing, playback returns to the previous file.
To return to a position a short while ago
Press during playback to return to a position 10 seconds earlier.
During playback, press REPLAY.
To advance to a position slightly ahead
Press during playback to forward to a position 30 seconds later.
During playback, press SHORT SKIP.
Playing in slow motion
While playback is paused, press and hold /.
• The speed switches each time the button is pressed (the speed is displayed on the TV screen).
• Reverse slow motion playback is not possible.
To resume normal playback
• Press .
Step forward and step reverse
While playback is paused, press /.
• The picture moves a step forward each time the button is pressed.
• Step reversing is not possible.
To resume normal playback
• Press .
Playing a specific section within a title or track repeatedly (A-B Repeat)
Use this procedure to play a specific section within a title or track repeatedly.
1 During playback, press A-B to select the starting point.
[A-] is displayed on the TV screen.
2 During playback, press A-B to select the ending point.
• A-B Repeat playback starts.
To cancel A-B Repeat play
• Press A-B during the A-B Repeat play.
Note
• A-B Repeat play is canceled in the following cases:
– When you search outside of the repeat range.
– When you start other Repeat Play or Random Play.
Playing repeatedly (Repeat Play)
Use this procedure to play the currently playing disc, title, chapter, track or file repeatedly.
During playback, press REPEAT.
• Each time you press REPEAT the type of repeat modes changes as shown below.
BD
Current chapter Current title
DVD
Current chapter Current title All titles
CD/Video file/Audio file/Image file
Current track/file All tracks/All files in folder
04
23
En
To cancel Repeat Play
04
• Press REPEAT several times during Repeat Play.
Note
• Repeat Play is canceled in the following cases:
– When you search outside the repeat range.
– When you start other Repeat Play or Random Play.
Playing in the desired order (Programmed Play)
1 During playback, press PROGRAM.
• The program screen is displayed.
2 Select the program number. Use / to select, then press ENTER.
3 Select the track/title/chapter you want to play. Use /// to select, then press ENTER.
4 Press .
• Playback starts.
Editing the program
1 Select the program number you want to edit, then press ENTER.
2 Select title/chapter, then press ENTER.
Deleting the program
Select the program number you want to delete,
then press CLEAR.
• To delete all the programs, press RETURN.
Note
• When you use audio CDs for Programmed Play, enter
the track number in step 3.
• This function does not work with BDs.
Making bookmarks
You can make bookmarks on the video currently playing and play back the scene later.
During playback, press BOOKMARK.
• The bookmark is made.
• Maximum number of bookmarks are 12.
Playing the bookmarked scene
1 Press and hold BOOKMARK for a few seconds.
• The list of bookmarks is displayed.
2 Select the bookmark you want to play. Use / to select, then press ENTER.
24
En
Deleting the bookmark
Select the bookmark you want to delete, then
press CLEAR.
• Bookmarks may not be allowed to make for some discs.
• Bookmarks are canceled in the following cases:
– When the player’s power turned off.
– When the disc tray is opened.
Zoom
During playback, press ZOOM.
• Each time you press ZOOM, the zoom level changes as shown below.
[Zoom 2x] [Zoom 3x] [Zoom 4x] [Zoom 1/2] [Zoom 1/3] [Zoom 1/4] Normal (not displayed)
Note
• This function does not work with some discs.
Playing photos as slideshows
This function plays the photos, switching them automatically.
During playback, press INDEX.
• Display the thumbnail of image files. The maximum number is 12 at once.
• If you select one of the image and press ENTER, slideshow will start from the image you selected.
Rotating/inverting photos
When a slideshow is playing or paused, the display switches as shown below when the /// buttons are pressed.
button: Rotates 90° clockwise button: Rotates 90° counterclockwise button: Flips horizontally button: Flips vertically
Switching the camera angles
For BD-ROM and DVD-Video discs on which multiple angles are recorded, the angles can be switched during playback.
1 During playback, press FUNCTION.
2 Select Angle from the FUNCTION menu.
• The current angle and total number of recorded angles are displayed on the TV screen.
• If the angles are not switched, switch them from the disc menu screen.
Note
• Some discs cannot switch angles.
Switching the subtitles
For discs or files on which multiple subtitles are recorded, the subtitles can be switched during playback.
Caution
• The subtitles cannot be switched for discs recorded by a DVD or BD recorder. Also refer to the operating instructions for the device used for recording.
During playback, press SUBTITLE.
• The current subtitle and total number of recorded subtitles are displayed on the TV screen. To switch the subtitle, press SUBTITLE again.
• The subtitles can also be switched by selecting Subtitle from the FUNCTION menu.
• If the subtitles are not switched when SUBTITLE is pressed, switch them from the disc menu screen.
Turning the subtitles off
Press SUBTITLE several times or select Subtitle
from the FUNCTION menu to switch the setting to Off.
About displaying external subtitle files while playing DivX media files
In addition to the subtitles recorded in DivX media files, this player also supports the display of external subtitle files. If a file has the same name as that of a DivX media file aside from the file extension and the extension is one of the extensions listed below, the file is treated as an external subtitle file. Note that DivX media files and external subtitle files must be located in the same folder. Only one external subtitle file can be displayed on this player. Use a computer, etc., to delete any external subtitle files you do not want to display from the disc. Text files with the extensions “.smi”, “.srt”, “.sub” and “.txt” are supported.
Note
• Depending on the file, the external subtitles may not be displayed properly.
Moving subtitles
The position of the subtitles displayed while playing BD­ROMs or DVDs can be moved.
1 Play the BD-ROM or DVD video and display the subtitles on the TV screen.
2 Press and hold the SUBTITLE button for at least 2 seconds.
•The
Subtitle shift mode is set.
•[
Subtitle shift mode] is displayed on the TV screen.
3 Use the / buttons to move the position of the subtitles.
•Use the / buttons to move the position of the
subtitles.
• Once the setting is complete, press ENTER.
4 Cancel the Subtitle shift mode. Press the ENTER button.
Switching the audio
For discs or files on which multiple audio streams/ channels are recorded, audio streams/channels can be switched during playback.
During playback, press AUDIO.
• The current audio and total number of recorded audio streams are displayed on the TV screen. To switch the audio, press AUDIO again.
• The audio can also be switched by selecting Audio from the FUNCTION menu.
• If the audio is not switched when AUDIO is pressed, switch it from the disc menu screen.
Switching the CD/SACD playback area
1 Select the area you want to play.
In the stop mode, press CD/SACD. The playback area switches on the front panel display window each time the button is pressed.
[CD AREA] [SACD 2CH] [SACD MCH] (back to beginning)
• During playback, press STOP twice to cancel continuous play before selecting the playback area.
04
Displaying the disc information
Press DISPLAY.
The disc information appears on the TV screen. To switch off the information display, press DISPLAY again.
The information display differs between during playback and when playback is stopped.
25
En
Enjoying BONUSVIEW or
04
BD-LIVE
This player is compatible with BD-Video BONUSVIEW and BD-LIVE.
When using BD-Video discs compatible with BONUSVIEW, you can enjoy such functions as secondary video (picture in picture) (page 28) and secondary audio (page 28). With BD-Video discs supporting BD-LIVE, special video images and other data can be downloaded from the Internet.
Data recorded on BD video and downloaded from BD­LIVE is stored on the USB flash drive (external memory). To enjoy these functions, connect a USB flash drive (minimum 1 GB capacity, 2 GB or greater recommended) supporting USB 2.0 High Speed (480 Mbit/s) to the USB port.
• When you insert or remove a USB flash drive, be sure to turn the player’s power off.
• To recall data stored in the USB flash drive, first insert the disc media that was being used at the time the data was downloaded (if a different disc is loaded, the data stored on the USB flash drive cannot be played).
• If a USB flash drive containing other data (previously recorded) is used, the video and audio may not play back properly.
• Do not disconnect the USB flash drive while playback is in progress.
• Some time may be required for the data to load (read/ write).
Caution
• It may not be possible to use the BONUSVIEW and BD-LIVE functions if there is insufficient space on the USB flash drive. In this case, refer to Erasing data that has been added to BDs and application data on page 42 for erasing the Virtual Package data and the BD-LIVE data in the USB flash drive.
Note
• Operation of USB flash drives is not guaranteed.
• Playback of BD-LIVE function data differs depending on the disc used. For details, consult the user instructions supplied with the disc.
• To enjoy the BD-LIVE function, a network connection and settings are required (pages
• BD-LIVE is a function that provides for connection to the Internet. Discs supporting the BD-LIVE function may send ID codes identifying this player and the disc to the contents provider via the Internet.
20 and 41).
26
En
Playback functions
The functions that can be used differ according to the type of disc and file. In some cases, some of the functions cannot be used. Check the usable functions on the table below.
Disc/file type
1
Function
2
Quick view
Forward and reverse scanning
BD-ROM
BD-R
/-RE
  
3
3
Short Skip/Replay  
Playing specific titles, chapters or tracks
  
Skipping content 
Slow motion play
Step forward and step reverse
A-B Repeat play
5, 6
7, 8
7


 
Repeat Play 
Zoom  
Angle
Subtitle
Audio
9
10
11

  
  
Disc information 
1. Some functions may not work for some discs or files, even if indicated [] on the table.
2. Depending on the audio format, such as Dolby TrueHD and DTS-HD Master Audio, the re might be no sound output during fast-forward.
3. Sound is not produced during forward and reverse scanning.
4. Sound is produced during forward and reverse scanning.
5. No sound is output during slow motion playback.
6. Reverse slow motion playback is not possible.
7. If a chapter is switched, some discs will cause an automatic return to normal playback.
8. Reverse step playback is not possible.
9. Angle mark is displayed for scenes at which multiple angles are recorded if Angle Mark is set to On (page 40).
10. • The types of recorded subtitles depend on the disc and file.
• In some cases, the subtitle may switch or the switching screen provided on the disc may be displayed immediately, without the current subtitle or the total number of subtitles recorded on the disc being displayed.
11. The types of recorded audio streams depend on the disc and file.
DVD-
Video
DVD-R
/-RW
AVCREC AVCHD
(VR
format)
3
3
3
Video
Image
Audio
file
file
3
3


file
Audio
CD
4
4
04
27
En
Using the FUNCTION
04
menu
Various functions can be called out according to the player’s operating status.
1 Display the FUNCTION menu. Press FUNCTION during playback.
2 Select and set the item. Use / to select, then press ENTER.
Note
• Items that cannot be changed are displayed in gray. The items that can be selected depend on the player’s status.
To change the setting of the selected item
Use / to change.
To close the FUNCTION menu
Press FUNCTION.
FUNCTION menu item list
Item Description
Title (track)
Chapter Display the information for the currently
File Display current file information.
Time Display the elapsed or remaining time.
Mode Switch the play mode (page 29).
Audio Switch the audio.
Angle Switch the BD-ROM/DVD-Video disc’s
Subtitle Switch the subtitle language.
Code Page Switch the subtitle code page.
Secondary Video
Secondary Audio
Bitrate Display the bitrate of the audio/video/
Still off Switch off the BD-ROM’s still picture.
Short Skip Forward to a position 30 seconds later.
Replay Return to a position 10 seconds earlier.
Slide Show Switch the playback speed while playing
Transition Change the style of the slide show while
1. One of these types of information is displayed, depending on the
2. Secondary video mark is displayed for scenes at which secondary
3. Secondary audio mark is displayed for scenes at which secondary
1
type of disc.
video is recorded if PIP Mark is set to On (page 40).
audio is recorded if Secondary Audio Mark is set to On (page 40).
Display the title information for the currently playing disc and total number of titles on the disc. Also select the title you want to play. (See the following description.)
playing chapter (track/file) and total number of chapters in the disc. Also select the chapter (track/file) you want to play. (See the following description.)
Select your favorite file.
Also enter the time from which you want to start playback. (See the following description.)
camera angle.
2
Switch the BD-ROM’s secondary video (Picture-in-Picture).
3
Switch the BD-ROM’s secondary audio.
secondary video/secondary audio.
the picture slide show.
playing the picture slide show.
28
En
Note
• Selectable items depend on the type of disc.
• The types of recorded secondary audio streams depend on the disc and file.
• Some discs do not include secondary audio/ secondary video.
• In some cases, the secondary audio/secondary video may switch or the switching screen provided on the disc may be displayed immediately, without the current secondary audio/secondary video or the total number of secondary audio/secondary video streams recorded on the disc being displayed.
Playing from a specific time (Time Search)
1 Select Time. Use / to select, then press ENTER.
2 Input the time.
Use the number buttons (0 to 9) to input the time.
• To play from 45 minutes, input 0, 0, 4, 5, 0 and 0, then press ENTER.
• To play from 1 hour 20 minutes, input 0, 1, 2, 0, 0 and 0, then press ENTER.
• Press CLEAR to clear the values you have input.
3 Starting playback from the specified time. Press ENTER.
Playing a specific title, chapter, track or file (Search)
1 Select Title or Chapter (track/file). Use / to select, then press ENTER.
2 Input the Title or Chapter (track/file) number.
Use the number buttons (0 to 9) or / to input the number.
• To search for title 32, input 3 and 2, then press ENTER.
• Press CLEAR to clear the values you have input.
3 Starting playback from the specified title, cha pter or track. Press ENTER.
Playing specified range of discs, titles or chapter (track/ file) in random order
You can select from two types of random playback.
1 Select Mode. Use / to select, then press ENTER.
2 Select the playing mode. Use / to select, then press ENTER.
Random play
The specified range of discs, titles or chapter (track/file) is played in random order. The same item may be played consecutively.
Shuffle play
The specified range of discs, titles or chapter (track/file) is played in random order. Each item is played once.
Continuing playback from a specified position (Continued Viewing Playback)
This function allows you to continue playback from a position you specify to be played next time, even after turning the power off.
Setting
During playback, press CONTINUED at the
position from which you want to start continued viewing playback.
The elapsed playing time at the specified position is displayed on the TV screen.
Playing
1Press  to play the title for which you have set continued viewing playback.
The continued viewing playback confirmation screen appears.
• In the cases below, the continued viewing playback confirmation screen is displayed.
For BD videos
The screen is displayed after the main featured has been played.
For recorded discs
The screen is displayed after the folder is selected and the title set for continued viewing playback has been played.
2 Use / to select Yes, then press ENTER.
Playback starts from the specified position.
Note
• The continued viewing playback setting is canceled when OPEN/CLOSE is pressed.
• Continued viewing playback may not work properly with some discs.
04
29
En
Chapter 5
05
Playback from Home Media Gallery
Files stored in a PC or DMS (Digital Media Server) as described above can be played by Digital Media Player (DMP). The player supports the use of such DMP.
Files stored in a PC or DMS (Digital Media Server) as described above can be played via command from an external Digital Media Controller (DMC). Devices controlled by this DMC to play files are called DMRs (Digital Media Renderers). This player supports this DMR function. When in the DMR mode, such operations as playing and stopping files can be
About Home Media Gallery
This player’s Home Media Gallery function allows you to display a list of input sources and start playback. This chapter describes setup and playback procedures required to enjoy these features. When you play the files stored on your computer or the components on the network, it is advisory that you also refer to the operation manual supplied with your network component.
The input sources that can be played from Home Media Gallery are as shown below.
• BD-R/RE (BDAV format) discs
• DVD-R/RW (VR format) discs
• Audio CDs (CD-DA, SACD and DTS CDs)
• DVD/CDs on which only data files of video, image or audio files, etc. are recorded.
•USB device
• Files on the network servers (on the PCs or components connected to the player via LAN interface.)
Note
• The Home Media Gallery allows you to play files on media servers connected on an identical Local Area Network (LAN) as the receiver.
• The following files are allowed to be played from Home Media Gallery:
– PCs running Microsoft Windows Vista or XP with
Windows Media Player 11 installed
– PCs running Microsoft Windows 7 with Windows
Media Player 12 installed
– DLNA-compatible digital media servers (on PCs or
other components)
30
En
performed from the external controller.
• To play back audio files stored on components on the network, you must turn on the DHCP server function of your router. In case your router does not have the built-in DHCP server function, it is necessary to set up the network manually. Otherwise, you cannot play back files stored on components on the network. See “Setting the IP address” on page 41.
About network playback
The network playback function of this unit uses the following technologies:
Windows Media Player
See Windows Media Player 11/Windows Media Player 12 above for more on this.
DLNA
DLNA CERTIFIED® Audio Player
The Digital Living Network Alliance (DLNA) is a cross­industry organization of consumer electronics, computing industry and mobile device companies. Digital Living provides consumers with easy sharing of digital media through a wired or wireless network in the home.
The DLNA certification logo makes it easy to find products that comply with the DLNA Interoperability Guidelines. This unit complies with DLNA Interoperability Guidelines v1.5. When a PC running DLNA server software or a DLNA compatible device is connected to this player, some setting changes of software or other devices may be required. Please refer to the operating instructions for the software or device for more information.
®
DLNA
, the DLNA Logo and DLNA CERTIFIED® are trademarks, service marks, or certification marks of the Digital Living Network Alliance.
Content playable over a network
• Even when encoded in a compatible format, some files may not play correctly.
• Some functions may not be supported depending on the server type or version used.
• Supported file formats vary by server. As such, files not supported by your server are not displayed on this unit. For more information check with the manufacturer of your server.
Disclaimer for Third Party Content
Access to content provided by third parties requires a high speed Internet connection and may also require account registration and a paid subscription.
Third party content services may be changed, suspended, interrupted, or discontinued at any time without notice, and Pioneer disclaims any liability in connection with such occurrences.
Pioneer does not represent or warrant that content services will continue to be provided or available for a particular period of time, and any such warranty, express or implied, is disclaimed.
About playback behavior over a network
• Playback may stall when the PC is switched off or any media files stored on it are deleted while playing content.
• If there are problems within the network environment (heavy network traffic, etc.) content may not be displayed or played properly (playback may be interrupted or stalled). For best performance, a 10BASE-T/100BASE-TX connection between the player and the PC is recommended.
• If several clients are playing simultaneously, as the case may be, playback is interrupted or stalled.
• Depending on the security software installed on a connected PC and the setting of such software, network connection may be blocked.
Pioneer is not responsible for any malfunction of the player and/or the Home Media Gallery features due to communication errors/malfunctions associated with your network connection and/or your PC, or other connected equipment. Please contact your PC manufacturer or Internet service provider.
Windows Media is either a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries.
This product includes technology owned by Microsoft Corporation and cannot be used or distributed without a license from Microsoft Licensing, Inc.
Microsoft®, Windows®7, Windows®Vista, Windows®XP, Windows®2000, Windows®Millennium Edition, Windows®98, and WindowsNT® are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
Playback file on the network
1 Press HOME MENU to display the Home Menu screen.
2 Select [Home Media Gallery], and press ENTER.
3 Select the server which contains the file you want to play.
4 Select the file you want to play. Use / to select, then press ENTER.
To end Home Media Gallery
Press HOME MENU.
Disc/USB playback
1 Press HOME MENU to display the Home Menu screen.
2 Select [Home Media Gallery], and press ENTER.
3 Select Disc or USB. Use / to select, then press ENTER.
4 Select Photo/Music/Video/AVCHD.
Use / to select, then press ENTER.
• This step is not for the discs that have been recorded with BDAV/VR/AVCREC format.
• To play files in AVCHD format on a USB device, create a folder named “AVCHD” on the USB device, then copy the “BDMV” folder containing which the files to be played into the “AVCHD” folder.
5 Select the title/track or file you want to play.
Use / to select, then press ENTER.
Playback starts from the selected title/track or file.
• If the file you want to play is in the folder, select the folder that contains the file first.
05
31
En
Playing back image files
05
About Slideshow
A display of the files in the folder switches automatically.
Note
• Some BD-R/-RE discs have playback protection. To cancel the protection, input the password set for the disc.
• It may take a few seconds before playback starts. This is normal.
• It may not be possible to play some files properly.
• The number of views may be restricted.
• Depending on the connected devices and conditions, some time may be required for playback to start and for the image to switch.
Playing the Playlist
1 Press HOME MENU to display the Home Menu screen.
2 Select [Home Media Gallery], and press ENTER.
3 Select Playlist. Use / to select, then press ENTER.
4 Select the track/file to be played.
Use / to select, then press ENTER.
Playback starts from the selected track/file and continues until the end of the list is reached. Use / to play the previous or next track/file. The Now Playing screen is displayed.
Deleting tracks/files from the Playlist
Playing in the desired order (Playlist)
The discs that can add tracks and files to the Playlist are as shown below.
• DVDs/CDs/USB devices on which audio files are recorded
Adding tracks/files
Use this procedure to add tracks and files, and create the
Playlist.
1 Press HOME MENU to display the Home Menu screen.
2 Select [Home Media Gallery], and press ENTER.
3 Select Disc or USB.
Load the disc beforehand. Use / to select, then press ENTER.
4 Select the track/file to be added.
Use to select.
5 Press POP UP MENU to display the POP UP MENU menu.
6 Select Add to Playlist to add to Playlist.
Use / to select, then press ENTER. The track or file selected in step 4 is added to the Playlist.
• To add more tracks or files, repeat steps 4 to 6.
1 Select the track/file to be deleted, then press POP UP MENU to display the POP UP MENU menu.
2 Use / to select Remove from Playlist, then press ENTER.
Note
• In the following cases, all information in the playlist will be deleted.
– When you open the disc tray.
– When you turn off the power.
32
En
Connecting by MiracastTM/ Direct
About Wi-Fi
The Wi-Fi CERTIFIED Logo is a certification mark of the Wi-Fi Alliance.
The Wi-Fi Protected Setup Identifier Mark is a mark of the Wi-Fi Alliance.
Wi-Fi, Wi-Fi Protected Setup, Wi-Fi Direct, Miracast, WPA, WPA2 are marks of the Wi-Fi Alliance.
Use the unit’s Miracast/Wi-Fi Direct functions
Miracast and Wi-Fi Direct are functions for connecting your mobile devices to the unit without using a wireless LAN router.
Miracast is a function that allows you to display the videos on a mobile device as is on a large screen TV.
Wi-Fi Direct is a function that allows you to play back photo, music, and video files stored on a mobile device with the unit by installing a DLNA compliant application on your mobile device.
Caution
• Depending on the model, a connection might not be possible even for Miracast/Wi-Fi Direct compatible models.
• The connection procedure for Miracast/Wi-Fi Direct depends on the mobile device. For details, refer to the instruction manual for the mobile device.
• Depending on the specifications of the mobile device, or the type and version of the OS, it might not be compatible with the Miracast/Wi-Fi Direct function. For details, refer to the instruction manual for the mobile device.
• Some copyright protected contents, etc., might, depending on the type of content, not be displayed by the television and the mobile device.
• In some cases, depending on the radio wave environment conditions or mobile device you are using, video and audio may be interrupted.
TM
Wi-Fi
• In some cases, depending on the playback contents and the connection environment, video and audio may be interrupted.
• In some cases, whe n performing an operation on your mobile device, video and audio may be interrupted.
• As for the connection environment of Miracast/Wi-Fi Direct, please confirm it on the connection screen.
• When Miracast/Wi-Fi Direct is being connected, the connection to the Internet of this device is temporarily interrupted.
Note
• You can only connect one mobile device to the unit at a time with this function.
• If you want to connect a different mobile device, you will first need to disconnect the one that is currently connected.
• If the power to the unit is turned OFF (Standby) then this function will be terminated, and network settings will be returned to what they were before using this function.
• In order to use this function your mobile device must meet Wi-Fi specifications.
• The unit does not support mobile device control using a specialist application.
Display the Miracast/Wi-Fi Direct mode screen
1 Turn on the power of the TV.
2Press  STANDBY/ON to turn this unit's power on.
The Pioneer logo appears on the TV screen.
Note
• If the Pioneer logo is not displayed, check the following:
– If this unit is in the play mode, press STOP.
– If the home media gallery or home menu is
displayed, press HOME MENU to close the displayed screen.
3 Press Miracast to display the Miracast/Wi-Fi Direct mode screen.
• Settings to connect the unit and mobile devices will be started from this screen.
• Closing this screen will terminate the Miracast/Wi-Fi Direct connection.
• Resume play will be canceled automatically if one enters this screen.
05
33
En
Connecting by Miracast
05
You can connect to your mobile device if it has Miracast function in conformity with Wi-Fi standards.
Press Miracast to display the Miracast/Wi-Fi Direct mode screen.
• As for Miracast, some of the functions have different names depending on the mobile device. For details, refer to the instruction manual for the mobile device.
1 Turn on the Miracast setting on your mobile device.
A list of the devices that can be connected to the mobile device is displayed on the mobile device screen.
2 Select the device name “DIRECT-xxBD/BDP-80FD” for the unit appearing on the TV screen from the list displayed on your mobile device.
“xx” indicates the device’s identification number.
Caution
• If the name of the unit “DIRECT-xxBD/BDP­80FD”does not appear on your mobile device, press
RETURN on the remote control and then
Miracast and perform the controls again from the
Miracast/Wi-Fi Direct mode screen.
If the connection is successful, the screen of the mobile device is also displayed on the TV.
Note
• For instructions on operating your mobile devices, see their respective operating instructions.
Connect to device not compatible with Miracast/ Wi-Fi Direct
Normally connect using the procedure below.
1 Display the Miracast/Wi-Fi Direct mode screen.
2 At the Wi-Fi network settings on your mobile device, select this unit's device name, as displayed on the TV screen ("DIRECT-xxBD/BDP-80FD").
“xx” indicates the device’s identification number.
Caution
• If the name of the unit “DIRECT-xxBD/BDP­80FD”does not appear on your mobile device, press
RETURN on the remote control and then
Miracast and perform the controls again from the
Miracast/Wi-Fi Direct mode screen.
3 On your mobile device, input this unit's password, as displayed on the TV screen.
Note
• For instructions on operating your mobile devices, see their respective operating instructions.
34
En
Connecting by WPS
If your mobile device supports WPS (by push-button method), it can be connected.
1 Display the Miracast/Wi-Fi Direct mode screen.
2 Use / to select WPS, then press ENTER.
3 Use / to select Next, then press ENTER.
4 Within 2 minutes, turn on the mobile device’s WPS setting.
Once the connection is completed, [Connection Success] appears on the TV screen.
Note
• For instructions on operating your mobile devices, see their respective operating instructions.
5 Press ENTER.
This completes the connection.
The Miracast/Wi-Fi Direct mode screen is displayed.
Change SSID and password
Change the SSID and password used to connect the unit and a mobile device.
1Press  STANDBY/ON and the power to the unit will come on.
The Pioneer logo will be displayed on the TV screen.
2 Press Miracast to display the Miracast/Wi-Fi Direct mode screen.
3 Use / to select Refresh, then press ENTER.
SSID and password will be changed.
The connection between the unit and mobile device will be terminated.
Caution
• All connection settings that have been setup for mobile devices will be removed.
• The SSID and password will not change until an update (Refresh) is performed. You should periodically perform an update (Refresh) for security reasons.
After the connection is terminated, when using the unit’s Miracast/Wi-Fi Direct function again you will also need to set up the connection again.
Canceling the Miracast/Wi-Fi Direct connection
1 While the Miracast/Wi-Fi Direct mode screen is
displayed, press RETURN.
• The connection is canceled.
• The network settings set before using Miracast/Wi-Fi Direct are restored.
Note
• To play discs, USB devices or web contents when connected by Miracast/Wi-Fi Direct, close the Miracast/Wi-Fi Direct mode screen.
Playing a mobile device’s photos, music or video files
Send the photos, music or video files from your mobile device to this unit.
Note
• For instructions on operating your mobile devices, see their respective operating instructions.
• Depending on the mobile device, you may have to install software for transferring the photos, music or video files.
• Depending on the software of the mobile device, it may not work properly.
05
35
En
Chapter 6
06
Playing the web contents
You can enjoy some streaming contents on the Internet with the player.
Available web contents
•YouTube
• Picasa
Note
About YouTube
• This player supports the YouTube Leanback service.
• YouTube videos for mobile phones cannot be played.
• Some YouTube videos cannot be played.
About Picasa
• Picasa is available only in English. Refer to instructions at http://picasa.google.com/support/ for details.
– Register your user name and password on the PC
before you use Picasa Web Albums.
– When you access Picasa from this player for the
first time, select the New User icon and enter your registered user name and password.
• Depending on the Internet connection environment, it may not be possible to play web contents properly.
• To access to web contents, this player requires a broadband Internet connection. A contract with an Internet provider is required for a broadband Internet connection.
• Access to content provided by third parties requires a high speed Internet connection and may also require account registration and a paid subscription. Third party content services may be changed, suspended, interrupted, or discontinued at any time without notice, and Pioneer disclaims any liability in connection with such occurrences. Pioneer does not represent or warrant that content services will continue to be provided or available for a particular period of time, and any such warranty, express or implied, is disclaimed.
• Disc playback and this function cannot be used at the same time.
About the function for restricting access to harmful information on the Internet
• This unit is equipped with a function for restricting viewing of web contents, etc., you do not want your children or others to see.
• To use this restriction function, change the Internet settings (page 40).
Playing the items
Caution
• You must connect the player to the Internet beforehand. See Connecting to the network through LAN interface on page 20 for the details.
1 Display the selection screen.
The selection screen can be selected by pressing
HOME MENU then selecting Web Contents
Desired web content.
2 Select the type of web contents. Use / to select, then press ENTER.
3Press /// to select the item you want to play, then press ENTER.
Press STOP to stop playback.
•End of video playback.
Enjoying YouTube
1 Display the YouTube screen.
Press YouTube.
• For Playback/Stop/End, please refer to Playing the items above.
36
En
Chapter 7
Advanced settings
Changing the settings
07
Operating the Initial Setup screen
1 When playback is stopped, display the Home Menu screen.
Press HOME MENU.
Note
• The items that can be selected depend on the player’s status.
• In Options, the factory default settings are indicated in bold.
Setting Options Explanation
Display Setting
TV Screen 16:9 Full Select this when connecting to a wide (16:9) TV.
16:9 Normal Select this when connected to a wide (16:9) TV. 4:3 pictures are displayed
4:3 Pan&Scan Select this when connecting to a 4:3 screen TV and playing a 16:9 video. The
4:3 Letterbox Select this when connecting to a 4:3 screen TV and playing a 16:9 video. The
Video Adjust Standard Choose the video output mode.
Vivid
Cinema
Custom The quality of the playback picture can be adjusted according to the TV you
Noise Reduction 0 Choose the level of noise reduction.
1
2
3
with vertical black bars along the sides.
video will be played with the left and right sides of the image cut off to display on the 4:3 screen. (This function works if the disc is labeled for 4:3PS.)
video will be played with black bands at the top and bottom.
are using (page 40).
2 Select and set Initial Setup. Use / to select, then press ENTER.
3 Select the item and change the setting. Use /// to select, then press ENTER.
Closing the Initial Setup screen
Press HOME MENU or RETURN.
37
En
07
Setting Options Explanation
Audio Output
Digital Output Bitstream Select this to output digital audio signals directly.
Downmix Stereo Surround audio signals converted to linear PCM audio signals are converted
Max Sampling Frequency 48k Outputs audio signals that are limited to a sampling frequency below the set
• When playing back a sampling frequency file or a disk having a lower than or equal setting compared to the present setting, you can output it at the unchanged sampling frequency.
• Sources with sampling frequencies of over 192 kHz cannot be played.
• When playing copyright-protected discs or files, the signals are output with the sampling frequency limited to 48 kHz or below, regardless of this setting.
DRC (Dynamic Range Control)*
• This affects such audio signals as Dolby Digital, Dolby TrueHD, and Dolby Digital Plus.
• DRC affects audio signals output from the following audio output terminals:
– Analog audio signals output from the AUDIO OUT terminals – Linear PCM audio signals output from the DIGITAL OUT or HDMI OUT terminals
• Depending on the disc, the effect may be weak.
• The effect may differ depending on the speakers, the AV amplifier settings, etc.
*
• This affects such audio signals as Dolby Digital, Dolby TrueHD, and Dolby Digital Plus.
• DRC affects audio signals output from the following audio output terminals: – Analog audio signals output from the AUDIO OUT terminals
– Linear PCM audio signals output from the DIGITAL OUT or HDMI OUT terminals
• Depending on the disc, the effect may be weak.
• The effect may differ depending on the speakers, the AV amplifier settings, etc.
HDMI
Color Space RGB Select this to output the video signals as RGB signals. Choose this if the
Resolution Auto Select this to choose the resolution of the video signals output from the
PCM Select this to output digital audio signals converted to 2-channel audio
Reencode When a BD containing secondary audio and interactive audio is played, the
Off Select this to output audio signals other than digital audio signals.
Lt/Rt Surround for output (when the connected AV receiver or amplifier, etc., is
96k
192k
Off Select this to output audio signals without using the DRC function.
On Select this to adjust the range between the loudest and softest sounds
Auto Select to switch the DRC setting On/Off automatically according to the input
YCbCr Select this to output the video signals as YCbCr 4:4:4 signals.
YCbCr 422 Select this to output the video signals as YCbCr 4:2:2 signals.
Full RGB Select this to output the vide o signals as RGB signals. Choose this if the colors
480I/576I Output the video signals from the HDMI OUT terminal with the selected
480P/576P
720P
1080I
1080P
signals.
two audio signals are mixed and converted to Dolby Digital audio or DTS audio for output.
into 2-channel (stereo) signals for output.
compatible with Dolby Pro Logic, the AV receiver or amplifier outputs the linear PCM audio signals as surround audio signals).
sampling frequency from the DIGITAL OUT terminal. Select according to the performance of the connected device.
(dynamic range) for playback at average volume. Use this when it is hard to hear dialog or when watching movies at midnight.
audio signal from the disc. This only affects Dolby TrueHD signals.
colors seem too faint and the black seems too bright.
seem too dense and all the dark colors are displayed in a uniform black.
HDMI OUT terminal automatically.
resolution. The resolution can be changed by pressing HDMI, but Auto cannot be
selected. The resolution switches each time HDMI is pressed.
38
En
Setting Options Explanation
HDMI
HDMI Audio Out Bitstream Select this to output HDMI audio signals directly.
Control On Select this to control the player with the remote control of the connected AV
To use Sound Retriever Link and Stream Smoother Link function (pages 17), Control must be set to On.
HDMI Deep Color 30bits Select this when outputting the video signals with 30-bit color.
When [30bits] or [36bits] is selected, set the color space (page 38) to a setting other than YCbCr 422.
HDMI 1080P 24Hz On Select this when Resolution is set to Auto or 1080P and outputting 1080p/24
HDMI 3D Auto With 3D discs, the disc is played with 3D images.
3D Notice Yes This sets whether or not to display the 3D notice when playing 3D images.
Network
IP Address Setting Select this to set the IP address of the player and DNS server (page 41).
Proxy Server Only set the proxy server if so instructed by your Internet service provider (page 41).
Information Displays the values of the MAC address, IP address, subnet mask, default gateway, DNS server
Connection Test Select this to test the network connection (page 41).
BD-Live Connection Permitted All discs are allowed to connect to BD-LIVE.
DLNA Enable Select this when connecting to DLNA server.
Interface Ethernet Select when using a LAN cable to connect to the network.
Wireless Setting Perform settings for a wireless network connection (page 33).
Language
OSD available languages Choose a language for the on-screen displays from the listed languages.
Audio * For some discs, it may not
be possible to change to the selected language.
If a language not recorded on the BD/DVD is set, one of the recorded languages is automatically selected for playback.
Subtitle * For some discs, it may not
be possible to change to the selected language.
If a language not recorded on the BD/DVD is set, one of the recorded languages is automatically selected for playback.
Menu * For some discs, it may not
be possible to change to the selected language.
If a language not recorded on the BD/DVD is set, one of the recorded languages is automatically selected for playback.
PCM Select this to output HDMI audio signals converted to PCM audio signals.
Reencode When a BD containing secondary audio and interactive audio is played, the
Off Select this when you do not want to output the audio signal from the HDMI
Off Select this when you do not want to control the player with the remote control
36bits Select this when outputting the video signals with 36-bit color.
Off Select this when outputting the video signals with normal 24-bit color.
Off Select this when Resolution is set to 1080P and outputting 1080p/60 video
Off 3D images are not played.
No
(primary) and DNS server (secondary).
Partia l Permitted Only discs whose safety has been confirmed are allowed to connect to BD-LIVE.
Prohibited No disc is allowed to connect to BD-LIVE.
Disable Select this when not connecting to DLNA server.
Wireless Select when connecting wirelessly to the network.
available languages Choose a language from the listed languages to set the default audio
available languages Choose a language from the listed languages to set the default subtitle
available languages Choose a language from the listed languages to set the default language for
two audio signals are mixed and converted to Dolby Digital audio or DTS audio for output.
output terminal.
device using an HDMI cable. Also refer to page 17.
of the connected AV device using an HDMI cable.
video signals to a TV compatible with 1080p/24.
signals to a TV compatible with 1080p/60.
language for BD-ROM and DVD-Video playback.
language for BD-ROM and DVD-Video playback.
BD-ROM and DVD-Video menus.
07
39
En
07
Setting Options Explanation
Playback
Angle Mark On Select this to display the angle mark on the TV screen (page 24).
PIP Mark On Select this to display the PIP mark on the TV scre en.
Secondary Audio Mark On Select this to display the secondary audio mark on the TV screen (page 28).
®
DivX
VOD DRM
Internet Setting Permitted Web contents can be watched without entering the password.
To restrict the viewing of web contents, etc., by children or others, select [Partial Permitted] or [Prohibited].
Disc Auto Playback On Discs are played automatically after they are loaded.
Last Memory On Select this to save the point at which you last stopped playback, even after the
Use of a disk that does not support the function is not possible.
PBC (Play Back Control) On Select this to play Video-CDs (version 2.0) compatible with PBC using the
Setup Navigator Start making the settings using the Setup Navigator menu. For details, see page 21.
Security
Change Password Register (change) the password for parental lock settings or for unlocking to play DVD-Videos with
Parental Control Change the player’s parental lock level (page 42).
Country Code Change the Country/Area code (page 42).
Options
Screen Saver Off The screen saver is not activated.
Auto Power Off Off Select this if you do not want the power to turn off automatically.
Quick Start On Select to shorten the required time to boot up.
Update USB Storage Select the method of software updating (page 43).
Load Default Restore the settings to the factory default.
System Information Check the system version number.
BUDA BUDA Information Display and set up the BUDA data on the connected USB device (page 42).
Off Select this if you do not want to display the angle mark on the TV screen.
Off Select this if you do not want to display the PIP mark on the TV screen.
Off Select this if you do not want to display the secondary audio mark on the TV
Registration Code Displays the player’s registration code required to play DivX VOD files
Partial Permitted The password must be entered to watch web contents.
Prohibited No web contents can be watched.
Off Loaded discs do not start playing automatically.
Off Select this when you want to use only Continue Viewing Play (page 29).
Off Select this to play Video-CDs (version 2.0) compatible with PBC without using
the parental lock feature (page 42). The default password is "0000".
1 min
2 min
3 min
10 min The power will be automatically turned off if no operation has been performed
20 min
30 min
Off Select to perform normal bootup.
Network
BUDA Setup
screen.
(page 11).
disc tray is opened or you switch to the standby mode.
disc menu.
the disc menu.
The screen saver will be activated if no operation has been performed for
more than one minute/two minutes/three minutes.
During operation of the screen saver, [SCNSVR] is displayed on the front
panel display.
Operating the remote control can deactivate the screen saver.
for more than 10 minutes/20 minutes/30 minutes.
Adjusting the video
1 Select and set Display Setting Video Adjust.
Use / to select, then press ENTER.
2 Select Custom.
40
Use / to select, then press ENTER.
En
3 Select the item and change the setting.
Use / to select the item, then use / to change the setting. Once the setting is completed, press
RETURN to close the settings screen.
List of setting items
Item Description
Brightness Select this to adjust the TV screen’s
Saturation Select this to adjust the TV screen’s
Hue Select this to adjust the color (green and
Contrast Select this to adjust the TV screen’s
Sharpness Choose the level of sharpness.
CTI (Color Transient Improvement)
brightness.
saturation.
red) balance of the TV screen.
contrast.
Provides images with clearer color contours.
Setting the IP address
1 Select and set Network IP Address Setting Next Screen. Use / to select, then press ENTER.
2 Set IP address.
Use /// to set the IP address of the player or DNS server, then press ENTER.
Auto Set IP Address On – The player’s IP address is obtained
automatically. Select this when using a broadband router or broadband modem that has a DHCP (Dynamic Host Configuration Protocol) server function. This player’s IP address will automatically be allocated from the DHCP server.
Off – The player’s IP address must be set manually. Use the number buttons (0 to 9) to input the IP address, subnet mask and default gateway.
Caution
• Some time is required for the IP address setting.
Note
• Once the IP address is set, select [Connection Test] to check that the unit is properly connected.
• For information on the DHCP server function, refer to the operating instructions for the network device.
• You may need to contact your Internet service provider or network administrator when inputting the IP address manually.
Setting the proxy server
Only set the proxy server if so instructed by your Internet service provider.
1 Select and set Network Proxy Server Next Screen. Use / to select, then press ENTER.
2 Select and set Use or Not use at Proxy Server.
Use / to change, then press .
Use – Select this when using a proxy server.
Not use – Select this when not using a proxy server.
If you have selected Use, proceed to step 3.
3 Select and set Server Select Method.
Use / to change, then press .
IP Address – Input the IP address.
Server Name – Input the server name.
4 Input IP Address or Server Name.
Use the number buttons (0 to 9) to input the number if you select IP address in step 3. Use / to move the cursor.
When Server Name is selected in step 3, use the number buttons (0 to 9) to launch the software keyboard. Now use /// to select characters and items, then press
ENTER to input.
5 Input Port Number.
Press , then use the number buttons (0 to 9) to input the number.
6 Press ENTER to set.
Displaying the network settings
Select and set Network Information Next
Screen.
Use / to select, then press ENTER.
The MAC address, IP address, subnet mask, default gateway and DNS server (primary and secondary) settings are displayed.
When Auto Set IP Address is set to On, the values obtained automatically are displayed.
Note
• “0.0.0.0” is displayed when each IP address has not been set.
Testing the network connection
Select and set Network Connection Test
Start.
Use / to select, then press ENTER.
“Network is OK.” is displayed once the test is completed. If any other message is displayed, check the connections and/or settings (pages 20 and page 41).
Changing to other language at language setting
1 Select and set Language. Use / to select, then press ENTER.
2 Select and set OSD, Audio, Subtitle or Menu. Use / to select, then press ENTER.
3 Select and set the desired language. Use / to select, then press ENTER.
Note
• If a language not recorded on the BD/DVD is set, one of the recorded languages is automatically selected and played.
07
41
En
Erasing data that has been added to
07
BDs and application data
Use this procedure to erase data that has been added to BDs (data downloaded with the BD-LIVE function and data used with the BONUSVIEW function) and application data.
Caution
• Some time is required to erase the data.
• Do not unplug the power cord while data is being erased.
1 Select and set Options  BUDA  BUDA Setup. Use / to select, then press ENTER.
2 Select and set Fmt buda. Press ENTER.
Registering or Changing the password
Use this procedure to register or change the code number required for the Parental Lock settings.
About default password of this unit
The default password is “0000”.
• This unit might ask you to enter a password when you change the password.
• If you reset this unit, your password is simultaneously changed to the default setting.
1 Select and set Security Change Password Next Screen. Use / to select, then press ENTER.
2 Input the password.
Use the number buttons (0 to 9) to input the number, then press ENTER to set.
Use / to move the cursor.
3 Re-input the password.
Use the number buttons (0 to 9) to input the number, then press ENTER to set.
Use / to move the cursor.
• To change the password, input the previously registered password, then input the new password.
Changing the Parental Lock level for viewing DVDs/BD-ROMs
Some DVD-Video discs containing scenes of violence, for example, have Parental Lock levels (check the indications on the disc’s jacket or elsewhere). To restrict viewing these discs, set the player’s level to the level lower than the discs.
1 Select and set Security Parental Control Next Screen. Use / to select, then press ENTER.
2 Input the password.
Use the number buttons (0 to 9) to input the number, then press ENTER to set.
Use / to move the cursor.
3 Change the level. Use / to change, then press ENTER to set.
Note
• The level can be set to Off or between Level1 and Level8. When set to Off, viewing is not restricted.
Changing the Country/Area code
1 Select and set Security Country Code Next Screen. Use / to select, then press ENTER.
2 Input the password.
Use the number buttons (0 to 9) to input the number, then press ENTER to set.
Use / to move the cursor.
3 Change the country/area code.
Use / to change, then press ENTER to set. Refer to page 47.
Note
• We recommend making a note of the password.
• If you have forgotten the password, reset the player to the factory default setting, then register the password again (page 43).
42
En
Software updating
The player’s software can be updated using one of the methods shown below.
• Connecting to the Internet.
• Using a USB flash drive.
Product information on this player is provided on the Pioneer website. Check the website shown on page 7 for update and service information on your Blu-ray disc player.
Caution
• Do not perform the actions below while the software is being updated. Doing so will interrupt updating and could lead to malfunction.
– Disconnecting a USB memory device – Unplugging the power cord – Pressing the reset button.
• There are two processes for software updating, downloading and updating. Both processes may take a certain period of time.
• Other operations are defeated during software updating. Furthermore, updating process cannot be canceled.
Updating connecting to the Internet
1 Connect to the Internet.
2 When playback is stopped, display the Home Menu screen.
Press HOME MENU.
3 Select and set Initial Setup. Use / to select, then press ENTER.
4 Select and set Options Update Network Start. Use / to select, then press ENTER.
5 Updating starts.
Press ENTER.
• Software updating may take a certain period of time.
• When updating is completed, the unit restarts automatically.
Updating using a USB flash drive
• This unit supports USB flash drives formatted in FAT32, FAT16 or NTFS. When formatting a USB flash drive on your computer, do so with the settings below.
– File system: FAT32 – Allocation unit size: Default allocation size
• Only store the most recent update file on the USB flash drive.
• Do not use a USB extension cable to connect a USB flash drive to the player. Using a USB extension cable may prevent the player from performing correctly.
1 Plug in the USB flash drive on which the update file is stored.
2 When playback is stopped, display the Home Menu screen.
Press HOME MENU.
3 Select and set Initial Setup. Use / to select, then press ENTER.
4 Select and set Options Update USB Storage Start. Use / to select, then press ENTER.
5 Updating starts.
Press ENTER.
• Software updating may take a certain period of time.
• When updating is completed, the unit restarts automatically.
Restoring all the settings to the factory default settings
1 Check that the player’s power is turned on.
2 When playback is stopped, display the Home Menu screen.
Press HOME MENU.
3 Select and set Initial Setup. Use / to select, then press ENTER.
4 Select and set Options Load Default Next Screen. Use / to select, then press ENTER.
5 Select and set OK. Use / to select, then press ENTER.
07
Note
• When an update file is provided on the Pioneer website, use your computer to download it onto a USB flash drive. Carefully read the instructions on downloading update files provided on the Pioneer website.
• Store the update file in the root directory of the USB flash drive. Do not store it within a folder.
• Do not put any files other than the update file on the USB flash drive.
Note
• After restoring all the settings to the factory default
settings, use Setup Navigator to reset the player (page 21).
• When disposing of the product, we recommend you reset it to the factory default setting to delete the data.
43
En
Wireless network
07
connection
Wireless network setup
For the wireless network connection, the player needs to be set up for network communication. This adjustment can be done from the Setup menu. Adjust the NETWORK setting as follow. Setting up the access point or the wireless router is required before connecting the player to the network.
Preparation
Before setting the wireless network, you need to:
– set the access point or wireless router. – note the SSID and security code of the network.
Note
• This unit conforms to the IEEE802.11b/g/n Wi-Fi standards.
• Only 2.4 GHz is supported for the IEEE802.11n standards.
1 Select Initial Setup Network Interface Wireless and press ENTER.
• When making the wireless setting for the first time, Wireless Setting is displayed. Proceed to step 4.
• When already set to Wireless, proceed to step 2.
2 Select Initial Setup Network Wireless Setting Next Screen and press ENTER.
3 Select Yes and press ENTER to continue.
The new connection settings reset the current network settings.
4 Wireless Setting menu is displayed.
Use / to select Scan. Then select Next using the / and press ENTER.
5 The player scans the all available access points or wireless routers within range and display them as a list. Use / to select an access point or wireless router on the list, and then press ENTER.
• If you have security on your access point or wireless router, verify that the WEP or WPA key that was entered into the player matches the routerís information exactly. You need to input the security code as necessary.
6 How to enter the security code.
1 Select the security code section using /// and press ENTER to start the software keyboard.
2Use /// to select characters and items, and then press ENTER to input.
3 Select abc, ABC, or !@#$ using /// to switch to lower case characters, upper case characters, or symbols.
44
En
4 Finish entering the security code by selecting Enter using /// and pressing ENTER.
7 Select Next using /// and press ENTER. If it connects success, it will display connection success and IP is obtained.
8 Pressing ENTER ends Wireless Setting.
Note
• WEP security mode generally have 4 keys available on an access point or wireless routerís setting. If your access point or wireless router use WEP security, enter the security code of the key “No.1” to connect on your home network.
• An Access Point is a device that allows you to connect to your home network wirelessly.
Scan - The player scans the all available access points or wireless routers within range and display them as a list.
Manual - Your access point may not be broadcasting its access point name (SSID). Check your router settings through your computer and either set your router to broadcast SSID, or manually enter the access point name (SSID) in [Manual].
Auto - If your access point or wireless router that supports the Push Button Configuration method, select this option and press the Push Button on your access point or wireless router within 120 counts. You do not need to know the access point name (SSID) and security code of your access point or wireless router.
Note
• If there is no DHCP server on the network and you want to set the IP address manually, Please refer to Setting the IP address on page 41.
WPS setup (Wi-Fi Protected Setup)
WPS connection setting
WPS is abbreviation of Wi-Fi Protected Setup. A standard established by the Wi-Fi Alliance industry group for a function allowing settings related to interconnection of WPS compatible wireless LAN devices and encryption to be made with simple operations.
This unit supports push-button configuration and PIN code configuration.
PBC (Push Button Configuration)
Connection settings are made automatically simply by pressing the WPS buttons on the WPS compatible wireless LAN device. This is the simplest way of making the settings, and is possible when the WPS compatible wireless LAN device is equipped with WPS button.
PIN Input
Connection settings are made by inputting the 8-digit PIN code shown on the main display to the access point to which you selected. Follow the instructions shown in Connecting using PIN code configuration on the right.
When performing wireless settings set Initial Setup
Network Interface to Wireless.
1 Press HOME MENU. The HOME MENU screen is displayed.
2 Use /// to select Initial Setup and press ENTER. The Initial Setup screen is displayed.
3 Select Initial Setup Network  Wireless Setting Next Screen and press ENTER.
A confirmation screen is displayed.
4 Use / to select Yes, then press ENTER. The Wireless Setting screen is displayed.
5 Use / to select Auto, then press ENTER. The WPS (Wi-Fi Protected Setup) screen is displayed.
6 Use / to switch between [PBC] or [PIN] screens.
When connecting using PBC go to step 7. When connecting using PIN go to step 8.
7 When connecting using PBC (Push Button), on the [PBC] screen use / to select Next, then press ENTER.
Then press the WPS button on the access point within 120 seconds.
8 When connecting using PIN confirm the PIN Code on the [PIN] screen. Use cursor then press ENTER.
9 Enter into the access point the PIN Code that you confirmed in step 8 above.
The PIN Code input method differs depending on the LAN device used. For details, consult the operating instructions accompanying your LAN device.
/ to select Next,
07
45
En
About how digital audio formats are output
07
Setting Bitstream PCM Re-encode
Only the primary audio (the main sound for movies, etc.) is
Method of conversion
terminal(s)
Audio type
Dolby Digital Dolby Digital Dolby Digital PCM 5.1ch
Dolby Digital Plus
Dolby TrueHD
DTS Digital Surround
DTS-HD High Resolution
3
Audio
DTS-HD Master Audio
PCM PCM 7.1ch
AAC AAC AAC PCM 5.1ch AAC AAC
SACD (DSD)
1. In case of Quick View (Quick view with audio), the audio output will be equal to the PCM setting regardless of any other settings. The LFE channel, however, is not output (5.1 5.0, 7.1 7.0).
2. If there is no secondary audio or interactive audio, depending on the disc the signals may be output without being re-encoded.
3. Quick View (Quick view with audio) function cannot be performed.
4. For multi-channel audio, the sound is converted into 2-channel audio for output.
5. When Resolution is set to 480I or 480P, or even when it is set to Auto, if the connected device does not support 480i/480p, the DSD multi­channel audio of SACDs is output in two channels, front left and front right (page 38).
6. When HDMI Audio Out is set to Bitstream, the sound is not output (page 39).
output. The secondary audio and interactive audio are not output.
Output
HDMI OUT
terminal
Dolby Digital
Plus
3
Dolby TrueHD Dolby Digital PCM 7.1ch
DTS Digital
Surround
DTS-HD High
Resolution
Audio
DTS-HD
3
Master Audio
3
DSD
DIGITAL OUT
terminal
Dolby Digital PCM 7.1ch
DTS Digital
Surround
DTS Digital
Surround
DTS Digital
Surround
PCM 2 ch
5
PCM 2 ch
The primary audio, secondary audio and interactive audio are converted into PCM audio and
output simultaneously.
HDMI OUT
terminal
PCM 5.1ch
PCM 7.1ch
PCM 7.1ch
4
PCM 7.1ch Dolby Digital Dolby Digital
6
PCM 5.1ch
DIGITAL OUT
terminal
PCM 2 ch
PCM 2 ch
The primary audio, secondary audio and interactive audio are converted into PCM audio then
1
converted again into Dolby Digital audio or DTS audio and
output simultaneously.
HDMI OUT
terminal
Dolby Digital Dolby Digital
4
DTS Digital
Surround
6
PCM 5.1ch
2
DIGITAL OUT
terminal
DTS Digital
Surround
PCM 2 ch
6
AUDIO
OUTPUT
terminal
4
2 ch
6
2 ch
Note
• Depending on the disc, the number of channels may differ.
• Depending on the connected HDMI device, the HDMI output audio and number of channels may differ.
• The HDMI output audio and number of channels may differ when Resolution is set to 480I or 480P, as well as when set to Auto if the connected device only supports 480i/480p.
• Three types of audio are recorded on BD video discs.
– Primary audio: The main sound. – Secondary audio: Additional sound added supplementarily, such as comments by directors, actors, etc. – Interactive audio: Sounds such as clicks heard when operations are performed. The interactive audio differs from
disc to disc.
46
En
Language Code Table and Country/Area Code
Abkhazian, ab/abk, 0102 Afar, aa/aar, 0101 Afrikaans, af/afr, 0106 Albanian, sq/sqi, 1917 Amharic, am/amh, 0113 Arabic, ar/ara, 0118 Armenian, hy/hye, 0825 Assamese, as/asm, 0119 Aymara, ay/aym, 0125 Azerbaijani, az/aze, 0126 Bashkir, ba/bak, 0201 Basque, eu/eus, 0521 Belarusian, be/bel, 0205 Bengali, bn/ben, 0214 Bihari, bh/bih, 0208 Bislama, bi/bis, 0209 Breton, br/bre, 0218 Bulgarian, bg/bul, 0207 Burmese, my/mya, 1325 Catalan, ca/cat, 0301 Central Khmer, km/khm, 1113 Chinese, zh/zho, 2608 Corsican, co/cos, 0315 Croatian, hr/hrv, 0818 Czech, cs/ces, 0319 Danish, da/dan, 0401 Dutch, nl/nld, 1412 Dzongkha, dz/dzo, 0426 English, en/eng, 0514 Esperanto, eo/epo, 0515 Estonian, et/est, 0520 Finnish, fi/fin, 0609 Fijian, fj/fij, 0610 Faroese, fo/fao, 0615
French, fr/fra, 0618 Galician, gl/glg, 0712 Georgian, ka/kat, 1101 German, de/deu, 0405 Greek, el/ell, 0512 Guarani, gn/grn, 0714 Gujarati, gu/guj, 0721 Hausa, ha/hau, 0801 Hebrew, iw/heb, 0923 Hindi, hi/hin, 0809 Hungarian, hu/hun, 0821 Icelandic, is/isl, 0919 Indonesian, in/ind, 0914 Interlingua, ia/ina, 0901 Interlingue, ie/ile, 0905 Inupiaq, ik/ipk, 0911 Irish,
ga/gle, 0701
Italian, it/ita, 0920 Japanese, ja/jpn, 1001 Javanese, jw/jav, 1023 Kalaallisut, kl/kal, 1112 Kannada, kn/kan, 1114 Kashmiri, ks/kas, 1119 Kazakh, kk/kaz, 1111 Kinyarwanda, rw/kin, 1823 Kirghiz, ky/kir, 1125 Korean, ko/kor, 1115 Kurdish, ku/kur, 1121 Lao, lo/lao, 1215 Latin, la/lat, 1201 Latvian, lv/lav, 1222 Lingala, ln/lin, 1214 Lithuanian, lt/lit, 1220 Macedonian, mk/mkd, 1311
Malagasy, mg/mlg, 1307 Malay, ms/msa, 1319 Malayalam, ml/mal, 1312 Maltese, mt/mlt, 1320 Maori, mi/mri, 1309 Marathi, mr/mar, 1318 Mongolian, mn/mon, 1314 Moldavian, mo/mol, 1315 Nauru, na/nau, 1401 Nepali, ne/nep, 1405 Norwegian, no/nor, 1415 Occitan, oc/oci, 1503 Oriya, or/ori, 1518 Oromo, om/orm, 1513 Panjabi, pa/pan, 1601 Persian, fa/fas, 0601 Polish, pl/pol, 1612 Portuguese, pt/por, 1620 Pushto, ps/pus, 1619 Quechua, qu/que, 1721 Romanian, ro/ron, 1815 Romansch, rm/roh, 1813 Rundi, rn/run, 1814 Russian, ru/rus, 1821 Samoan, sm/smo, 1913 Sango, sg/sag, 1907 Sanskrit, sa/san, 1901 Scottish Gaelic, gd/gla, 0704 Serbian, sr/srp, 1918 Serbo-Croatian, sh/---, 1908 Shona, sn/sna, 1914 Sindhi, sd/snd, 1904 Sinhalese, si/sin, 1909 Slovak, sk/slk, 1911
Slovenian, sl/slv, 1912 Somali, so/som, 1915 Sotho, Southern, st/sot, 1920 Spanish, es/spa, 0519 Sundanese, su/sun, 1921 Swahili, sw/swa, 1923 Swati, ss/ssw, 1919 Swedish, sv/swe, 1922 Tagalog, tl/tgl, 2012 Tajik, tg/tgk, 2007 Tamil, ta/tam, 2001 Tatar, tt/tat, 2020 Telugu, te/tel, 2005 Thai, th/tha, 2008 Tibetan, bo/bod, 0215 Tigrinya,
ti/tir, 2009
Tonga (Tonga Islands),
to/ton, 2015
Tsonga, ts/tso, 2019 Tswana, tn/tsn, 2014 Turkmen, tk/tuk, 2011 Turkish, tr/tur, 2018 Twi, tw/twi, 2023 Ukrainian, uk/ukr, 2111 Urdu, ur/urd, 2118 Uzbek, uz/uzb, 2126 Vietnamese, vi/vie, 2209 Volapük, vo/vol, 2215 Welsh, cy/cym, 0325 Western Frisian, fy/fry, 0625 Wolof, wo/wol, 2315 Xhosa, xh/xho, 2408 Yiddish, ji/yid, 1009 Yoruba, yo/yor, 2515 Zulu, zu/zul, 2621
Anguilla, ai, 0109 Antigua and Barbuda, ag, 0107 Argentina, ar, 0118 Armenia, am, 0113 Australia, au, 0121 Austria, at, 0120 Azerbaijan, az, 0126 Bahamas, bs, 0219 Barbados, bb, 0202 Belarus, by, 0225 Belgium, be, 0205 Belize, bz, 0226 Bermuda, bm, 0213 Brazil, br, 0218 Bulgaria, bg, 0207 Canada, ca, 0301 Cayman Islands, ky, 1125 Chile, cl, 0312 China, cn, 0314 Colombia, co, 0315 Croatia, hr, 0818 Cyprus, cy, 0325 Czech Republic, cz, 0326 Denmark, dk, 0411 Dominica, dm, 0413 Dominican Republic, do, 0415
Estonia, ee, 0505 Finland, fi, 0609 France, fr, 0618 Georgia, ge, 0705 Germany, de, 0405 Greece, gr, 0718 Greenland, gl, 0712 Grenada, gd, 0704 Guyana, gy, 0725 Haiti, ht, 0820 Hong Kong, hk, 0811 Hungary, hu, 0821 Iceland, is, 0919 India, in, 0914 Indonesia, id, 0904 Ireland, ie, 0905 Israel, il, 0912 Italy, it, 0920 Jamaica, jm, 1013 Japan, jp, 1016 Kazakhstan, kz, 1126 Korea, Republic of, kr, 1118 Kyrgyzstan, kg, 1107 Latvia, lv, 1222 Liechtenstein,
li, 1209
Lithuania, lt, 1220
Luxembourg, lu, 1221 Macedonia, the Former Yugoslav Republic of, mk, 1311 Malaysia, my, 1325 Malta, mt, 1320 Mexico, mx, 1324 Moldova, Republic of, md, 1304 Monaco, mc, 1303 Montserrat, ms, 1319 Netherlands, nl, 1412 New Zealand, nz, 1426 Norway, no, 1415 Pakistan, pk, 1611 Peru, pe, 1605 Philippines, ph, 1608 Poland, pl, 1612 Portugal, pt, 1620 Puerto Rico, pr, 1618 Romania, ro, 1815 Russian Federation, ru, 1821 Saint Kitts and Nevis, kn, 1114 Saint Lucia, lc, 1203 Saint Vincent and the
Grenadines, vc, 2203 San Marino, sm, 1913 Singapore, sg, 1907
Slovakia, sk, 1911 Slovenia, si, 1909 Spain, es, 0519 Suriname, sr, 1918 Sweden, se, 1905 Switzerland, ch, 0308 Taiwan, Province of China,
tw, 2023
Tajikistan, tj, 2010 Thailand, th, 2008 Trinidad and Tobago, tt, 2020 Tunisia, tn, 2014 Turkey, tr, 2018 Turkmenistan, tm, 2013 Turks and Caicos Islands,
tc, 2003
Ukraine, ua, 2101 United Kingdom, gb, 0702 United States, us, 2119 Uruguay, uy, 2125 Uzbekistan, uz, 2126 Venezuela, ve, 2205 Virgin Islands, British, vg, 2207
Table
Language Code Table
Language name, language code, input code
Country/Area Code Table
Country/Area name, Country/Area code, input code
07
47
En
Chapter 8
08
Additional information
Cautions on use
Moving the player
If you need to move this unit, first remove the disc if there’s one loaded, and close the disc tray. Next, press STANDBY/ON to switch the power to standby, checking that the POWER OFF indication on the front panel display goes off. Wait at least 10 seconds. Lastly, disconnect the power cord.
Never lift or move the unit during playback — discs rotate at a high speed and may be damaged.
Place of installation
Select a stable place near the TV and AV system to which the unit is connected.
Do not place the player on top of a TV or color monitor. Keep it away from cassette decks or other components easily affected by magnetism.
Avoid the following types of places:
• Places exposed to direct sunlight
• Humid or poorly ventilated places
• Extremely hot or cold places
• Places subject to vibration
• Places in which there is much dust or cigarette smoke
• Places exposed to soot, steam or heat (in kitchens, etc.)
Do not place objects on top
Do not place objects on top of the player.
Do not obstruct the ventilation holes
Do not use the player on a shaggy rug, bed, or sofa, and do not cover the player with a cloth, etc. Doing so will prevent heat dissipation and could lead to damage.
Keep away from heat
Do not place the player on top of an amplifier or other device generating heat. When installing in a rack, to avoid the heat generated by the amplifier and other devices, place it on a shelf below the amplifier whenever possible.
Turn the power off when not using the player
Depending on the conditions of the TV broadcast signals, striped patterns may appear on the screen when the TV is turned on while the player’s power is turned on. This is not a malfunction with the player or TV. If this happens, turn the player’s power off. In the same way, noise may be heard in the sound of a radio.
Condensation
If the player is moved suddenly from a cold place into a warm room (in winter, for example) or if the temperature in the room in which the player is installed rises suddenly due to a heater, etc., water droplets (condensation) may form inside (on operating parts and the lens). When condensation is present, the player will not operate properly and playback is not possible. Let the player stand at room temperature for 1 or 2 hours with the power turned on (the time depends on the extent of condensation). The water droplets will dissipate and playback will become possible.
Condensation can also occur in the summer if the player is exposed to the direct wind from an air-conditioner. If this happens, move the player to a different place.
Cleaning the player
Normally, wipe the player with a soft cloth. For tough dirt, apply some neutral detergent diluted in 5 to 6 parts water to a soft cloth, wring out thoroughly, wipe off the dirt, then wipe again with a dry cloth.
Note that getting alcohol, thinner, benzene or insecticide on the player could cause the print and coating to peel off. Also, avoid leaving rubber or vinyl products in contact with the player for long periods of time, as this could damage the cabinet.
When using chemical-impregnated wipes, etc., read the wipe’s cautions carefully.
Unplug the power cord from the power outlet when cleaning the player.
Caution for when the unit is installed in a rack with a glass door
Do not press the OPEN/CLOSE on the remote control to open the disc tray while the glass door is closed. The door will hamper the movement of the disc tray, and the unit could be damaged.
48
En
Cleaning the pickup lens
The player’s lens should not become dirty in normal use, but if for some reason it should malfunction due to dust or dirt, consult your nearest Pioneer authorized service center. Although lens cleaners for players are commercially available, we advise against using them since some may damage the lens.
Handling discs
Do not use damaged (cracked or warped) discs.
Do not scratch the disc’s signal surface or let it get dirty.
Do not load more than one disc into the player at a time.
Do not glue paper or put stickers onto the disc, or use a pencil, ball-point pen or other sharp-tipped writing instrument. These could all damage the disc.
Storing discs
Always store discs in their cases, and place the cases vertically, avoiding places exposed to high temperatures or humidity, direct sunlight or extremely low temperatures.
Be sure to read the cautions included with the disc.
Cleaning discs
It may not be possible to play the disc if there are fingerprints or dust on it. In this case, using a cleaning cloth, etc., to wipe the disc gently from the center toward the outer edge. Do not use a dirty cleaning cloth.
Condensation on discs
If the disc is moved suddenly from a cold place into a warm room (in winter, for example), water droplets (condensation) may form on the disc surface. Discs will not play properly if there is condensation on them. Carefully wipe off the water droplets from the disc surface before using the disc.
08
Do not use benzene, thinner or other volatile chemicals. Also do not use record spray or antistatic agents.
For tough dirt, apply some water to a soft cloth, wring out thoroughly, wipe off the dirt, then wipe off the moisture with a dry cloth.
Specially shaped discs
Specially shaped discs (heart-shaped, hexagonal, etc.) cannot be used on this player. Never use such discs, as they will damage the player.
49
En
Troubleshooting
08
Incorrect operation is often mistaken for trouble or malfunction. If you think that there is something wrong with this component, check the points below. Sometimes the trouble may lie in another component. Inspect the other components and electrical appliances being used. If the trouble cannot be rectified even after checking the points below, ask your nearest Pioneer authorized service center or your dealer to carry out repair work.
Playback
Problem Check Remedy
• Disc does not play.
• Disc tray opens automatically.
No picture is displayed or the picture is not displayed properly.
Playback stops. • Playback may stop if the unit is subject to shocks or set in an unstable
Is the disc one that is playable on this player?
Is the file one that is playable on this player?
Is the disc scratched? It may not be possible to play scratched discs.
Is the disc dirty? Clean the disc (page 49).
Is there a piece of paper or sticker attached to the disc?
Is the disc properly set in the disc tray?
Is the region number correct? See page 10 for the region numbers of discs that can be played on this
Is the HDMI cable properly connected?
Is the HDMI cable damaged? If the cable is damaged, replace it with a new one.
Is the input setting on the connected TV or AV receiver or amplifier right?
Is the output video resolution properly set?
Is the player connected with an HDMI cable other than a
High Speed HDMI (with a Standard HDMI
cable)?
Is a DVI device connected? The picture may not be displayed properly if a DVI device is connected.
Is Color Space properly set? Change the Color Space setting (page 38).
®/TM
• Check whether the disc is one that can be played on this player (page 8).
• Discs that have not been finalized cannot be pl ayed.
• Check whether the file is one that can be played on this player (page 11).
• Check whether or not the file is damaged.
The disc may be warped and unplayable.
• Set the disc with the printed side facing up.
• Set the disc properly in the depression in the disc tray.
player.
• Eliminate any condensation inside the unit (page 48).
• Depending on how the disc was recorded, the status of the pickup and compatibility between the disc being used and this unit, it may not be possible to play the disc properly.
• If the recorded time is short, it may not be possible to play the disc properly.
• BD-RE/-R discs recorded in formats other than BDM V or BDAV cannot be played.
• Connect the cable properly according to the connected devices (page 16).
• Disconnect the cable, then reinsert it firmly and all the way in.
Read the operating instructions for the connected components and switch to the proper input.
Switch the resolution at which the video and audio are output by pressing HDMI.
Connect the player to the TV using a High Speed HDMI
cable
®/TM
place.
• Playback may stop when a USB device is connected or disconnected during playback. Do not connect or disconnect USB devices during playback.
®/TM
cable.
50
En
Problem Check Remedy
Picture freezes and the front panel and remote control buttons stop working.
• Picture is stretched.
• Picture is cropped.
• Aspect ratio cannot be switched.
Picture is interrupted. The picture may be interrupted when the resolution of the recorded
There is square noise (pixelation) on the screen.
The subtitles cannot be switched.
• No sound is output.
• Sound is not output properly.
Left/right audio channels are inverted or only one side is produced.
Is the TV’s aspect ratio properly set?
Is TV Screen properly set? Set TV Screen properly (page 37).
Is the volume set to the minimum?
Is the disc played back in slow motion?
Is t he di sc pl ayed back in fa st forward or fast reverse?
Are the audio cables properly connected?
Is the audio cable damaged? If the cable is damaged, replace it with a new one.
Is Audio Output properly set?
Are the connected components (AV receiver or amplifier, etc.) properly set?
Is HDMI Audio Out properly set?
Is the output video resolution properly set?
Is a DVI device connected? The sound will not be output from the HDMI OUT terminal if a DVI
Are the audio cables properly connected?
• Press STOP to stop playback, then restart playback.
• If the playback cannot be stopped, press STANDBY/ON on the player’s front panel to turn off the power, then turn the power back on.
• If the power cannot be turned off (to standby), reset the unit. Use a thin rod to press the reset button on the main unit’s front panel. The unit restarts and can now be operated.
• It may not be possible to play scratched discs.
Read the operating instructions for the TV and set the TV’s aspect ratio properly.
When video signals with a resolution of 1080/50i, 1080/50p, 720/50p, 1080/24p, 1080/60i, 1080/60p or 720/60p are being output from the
HDMI OUT
even if
video signal switches. Set Resolution to something other than Auto (page 38).
Due to the characteristics of digital image compression technology, block-shaped images may stand out, for example in scenes where there is fast movement.
The subtitles cannot be switched for discs recorded on a DVD or BD recorder.
If the volume of the TV or AV amplifier is set to the minimum, raise it.
No sound is output during slow motion play and forward and reverse scanning.
• Connect the cable properly according to the connected devices (page 16).
• Insert the cable firmly and all the way in.
• If the connection plug or terminal is dirty, wipe it clean.
Set Audio Output properly, according to the connected device (page 38).
Read the operating instructions for the connected components and check the volume, input, speaker settings, etc.
Set HDMI Audio Out to Re-encode or PCM. (page 39).
Switch the resolution at which the video and audio are output by pressing HDMI.
device is connected. Connect the device to a DIGITAL OUT terminal or the AUDIO OUT terminals (page 19).
• For some BDs, audio signals are only output from DIGITAL OUT terminal or the HDMI OUT terminal.
• The sound may not be output for discs containing sound other than audio signals or non-standard sound.
• When copy-protected discs are played, the picture or sound may not be properly output. This is not a malfunction.
Check whether the audio cables for the left and right channels are inverted or whether the cable for one side is disconnected (page 19).
terminal, they may be output with an aspect ratio of 16:9
TV Screen
is set to
4:3 Pan&Scan
(page 37).
08
51
En
Problem Check Remedy
08
Multi-channel sound is not output.
Noise can be heard when outputting DTS Digital Audio signals from the DIGITAL OUT terminal.
192 kHz or 96 kHz digital audio signals cannot be output from the DIGITAL OUT terminal.
Secondary audio or interactive audio is not output.
After a disc is inserted, Loading stays displayed and playback does not start.
is displayed in file names, etc.
A message indicating low memory appears while playing a BD-ROM disc.
Is the audio output of the connected AV receiver or amplifier, etc., properly set?
Is multi-channel sound selected?
Is the connected AV receiver or amplifier compatible with DTS Digital Surround?
Is HDMI Audio Out properly set?
Are Digital Output properly set?
Are there too many files recorded on the disc?
Read the operating instructions for the connected AV receiver or amplifier and check the audio output settings of the AV receiver or amplifier.
Use the menu screen or AUDIO to switch the disc’s sound to multi­channel.
If an AV receiver or amplifier that is not compatible with DTS Digital Surround is connected to the DIGITAL OUT terminal, set Digital Output to PCM (page 38).
• Copyright-protected audio is converted to 48 kHz or less before output.
• Set Max Sampling Frequency to 96KHz or 192KHz (page 38).
When listening to the sound from an HDMI OUT terminal, set HDMI Audio Out to PCM (page 39).
When listening to the sound from an DIGITAL OUT terminal, set Digital Output to Re-encode or PCM (page 38).
When a disc on which files are recorded is inserted, depending on the number of files recorded on the disc, loading may take several dozen minutes.
The characters that cannot be displayed on this player are displayed in .
• Connect a USB device (page 19).
• Erase the data stored on the connected USB device from BUDA Setup (page 42).
52
En
Control function
Problem Check Remedy
Control function does not work.
Is the HDMI cable properly connected?
Is the HDMI cable you are using a High Speed HDMI
TM
Cable?
Is this player connected to the TV using an HDMI cable to watch the picture?
Is Control set to On on the player?
Does the connected device support the Control function?
Is Control set to On on the connected device?
Are multiple players connected?
®
To use the Control function, connect the TV and AV system (AV receiver or amplifier, etc.) to the HDMI OUT terminal (page 16).
Use a High Speed HDMI
/
prop erly if an HDMI cab le other than a High Speed HD MI used.
If video signals are being output from a terminal other than the HDMI OUT terminal, the Control function does not work. Connect to the TV using an HDMI cable (page 16).
Set Control to On on the player (page 39).
• The Control function will not work with devices of other brands that do not support the Control function, even when connected using an HDMI cable.
• The Control function will not work if devices that do not support the Control function are connected between the Control-compatible device and the player. See page 17.
• Even when connected to a Pioneer product compatible with the Control function, some of the functions may not work.
Also refer to the operating instructions for the connected device.
Set Control to On on the connected device. The Control function operates when Control is set to On for all devices connected to the HDMI OUT terminal. Once connections and settings of all the devices are finished, be sure to check that the player’s picture is output to the TV. (Also, check after changing the connected devices and connecting and/or disconnecting HDMI cables.) If the player’s picture is not being output to the TV, the Control function may not work properly. For details, refer to the operating instructions of the connected device.
The Control function may not work if 4 or more players, including this player, are connected by an HDMI cable.
Depending on the connected device, the function may not work.
®/TM
Cable. The Control function may not work
®/TM
08
Cable is
Network
Problem Check Remedy
Cannot connect to network. • Insert the LAN cable securely as far as it goes (page 20).
BD-LIVE function (connection to the Internet) cannot be used.
Software updating is slow. Depending on the Internet connection and other conditions, some time
• Do not connect using a modular cable. Use a LAN cable for the LAN (10/100) terminal.
• Check that the power of the Ethernet hub (router with hub function) or the modem is turned on.
• Check that the Ethernet hub (router with hub function) or the modem is properly connected.
• Check the network settings.
• Check the network connections and settings.
• Connect a USB memory device.
• Delete data from the USB memory device.
• Check that the BD-ROM supports the BD-LIVE function.
• Test the connections (page 41). If "Network is OK" is displayed, check the proxy server settings at [Initial Setup] -> [Network] -> [Proxy Server] -> [Next Screen] (page 40). There may also be a problem with the Internet connection. Contact your provider.
may be required to update the software.
53
En
Problem Check Remedy
08
A message other than “Networks is OK.” is displayed when Connection Test is performed.
The audio files stored on components on the network, such as a computer, cannot be played back.
The audio files stored on components on the network, such as a computer, cannot be played back.
Playback does not start. The component is currently
The computer is not properly operated.
Cannot access Windows Media Player 11 or Windows Media Player 12.
54
En
Is “Network is FAILED.” displayed?
Is the Ethernet hub (or router with a hub functionality) operating properly?
The audio component on the network which has been switched off is switched on.
Audio files recorded in MPEG-4 or AAC are being played back on Windows Media Player 11 or Windows Media Player 12.
The folder stored on the omponent connected to the network has been deleted or damaged.
disconnected from this unit or the power supply.
The corresponding IP address is not properly set.
You are currently logged onto the domain through your computer with Windows 7 installed.
• Check that this player and the Ethernet hub (or router with a hub functionality) are properly connected.
• If the IP address is obtained using the DHCP server function, check the setting is correct at the Information (page 39). For details on the DHCP server function, see the operating instructions for the Ethernet hub (or router with a hub functionality).
• Set the IP address manually.
• Check the operation and settings of the DHCP server function of the Ethernet hub (or router with hub functionality). For details on the DHCP server function, see the operating instructions for the Ethernet hub (or router with a hub functionality).
• If this player has been set manually, reset the IP address of this player or other components.
• Check the settings and operation the Ethernet hub (or router with a hub functionality). For details, see the operating instructions for the Ethernet hub.
• Reboot the Ethernet hub (or router with a hub functionality).
There are cases where a component with Internet security software installed cannot be accessed.
Switch on the audio component on the network before switching on this unit.
If the client is automatically authorized, you need to enter the corresponding information again. Check whether the connection status is set to “Do not authorize”.
Check the audio files stored on the component connected to the network.
Install Windows Media Player 11 or Windows Media Player 12 on your computer.
Play back audio files recorded in MP3, WAV (LPCM only), MPEG-4 AAC, or W MA. No te tha t some a udio f iles r ecord ed in th ese fo rmats may no t be played back on this unit.
Audio files recorded in MPEG-4 AAC cannot be played back on Windows Media Player 11 or Windows Media Player 12. Try using another server. Refer to the operation manual supplied with your server.
Check whether the component is affected by special circumstances or is in the sleep mode. Try rebooting the component if necessary.
Try changing the settings for the component connected to the network.
Check the folder stored on the component connected to the network.
Check the computer’s network settings, security settings, etc.
Check whether the component is properly connected to this unit or the power supply.
Sw itch on t he b uil t-in DHC P se rve r fun cti on o f yo ur ro ute r, o r se t up t he network manually according to your network environment.
The automatic configuration process takes time. Please wait.
Instead of logging onto the domain, log onto the local machine.
Problem Check Remedy
Video and audio playback are undesirably stopped or disturbed.
The LAN cable is currently disconnected.
There is heavy traffic on the network with the Internet being accessed on the same network.
There is a connection routed through a wireless LAN on the same network.
Check whether the audio file was recorded in a format supported by this unit.
Even audio files listed as playable on this unit may sometimes not be played back or displayed.
Check whether the folder has been damaged or corrupted.
Connect the LAN cable properly.
Use 100BASE-TX to access the components on the network.
• There may be a shortage of bandwidth on the 2.4 GHz band used by the wireless LAN. Make wired LAN connections not routed through a wireless LAN.
• Install away from any devices emitting electromagnetic waves on the
2.4 GHz band (microwave ovens, game consoles, etc.). If this does not solve the problem, stop using other devices that emit electromagnetic waves.
08
55
En
Wireless LAN
08
Problem Check Remedy
Network cannot be accessed via wireless LAN.
Cannot connect with the Miracast/Wi-Fi Direct function.
There is a connection on the mobile device but the mobile device video is not displayed on the TV (Miracast function).
56
En
This unit and wireless LAN router etc. are too far apart, or there is an obstacle between them.
There is a microwave oven or other device generating electromagnetic waves near the wireless LAN environment.
Multiple wireless devices are connected to the wireless LAN router.
Connection settings between the unit and the wireless LAN router etc. are not set up correctly.
The IP address settings for the unit and the wireless LAN router etc. (including DHCP settings) do not match.
The access point is set to conceal the SSID.
The access point’s security settings use WEP 152-bit le ngt h c ode key or sha red ke y authentication.
Is the Miracast/Wi-Fi Direct Mode screen displayed on the TV or is [READY] displayed on the unitís display window?
Check the SSID and password in the Miracast/Wi­Fi Direct Mode screen.
Is the mobile device compliant with Wi-Fi D irect or Miracast?
Is the mobile device compliant with Miracast?
Improve the wireless LAN environment by taking steps such as moving the unit and wireless LAN router etc. closer together.
• Use the unit in a place away from microwave ovens or others device generating electromagnetic waves.
• Avoid using devices generating electromagnetic waves as much as possible when using the unit with a wireless LAN.
When connecting mult iple wireless devices, their IP addresses must be changed.
If the connection settings between the unit and the wireless LAN router etc. are not set up correctly, connection settings much be performed in order to connect the unit and the wireless LAN router etc.
• Check the IP address settings of the unit and the wireless LAN router etc. (including the DHCP setting).
• If the unit’s DHCP setting is on, turn the unit’s power off, then turn the power back on. Check that the IP address of the unit matches the settings of the wireless LAN router etc.
• If the unit’s DHCP setting is off, set an IP address matching the network of the wireless LAN router etc.
For example, if the wireless LAN router’s IP address is “192.168.1.1”, set the unit’s IP address to “192.168.1.XXX” (*1), the subnet mask to “255.255.255.0”, and the gateway and DNS to “192.168.1.1”.
(*1) Set the “XXX” in “192.168.1.XXX” to a number between 2 and 248 that is not assigned to other devices.
In this case, the SSID may not be displayed on the access point list screen. If not, set the SSID etc. by setting the wireless LAN settings on the receiver manually.
The unit does not support WEP 152-bit length code key or shared key authentication.
Press Fi Direct Mode Screen. Then press Miracast and perform the controls again from the Miracast/Wi-Fi Direct Mode Screen.
If an update was performed in the Wi-Fi Direct Mode screen or the unit was restored to the default settings, the SSID and password will have changed.
Enter the newly set SSID and password on the mobile device.
Only mobile devices that are compliant with Wi-Fi Direct or Miracast are supported.
Ask the manufacturer of the corresponding device whether the mobile device is compliant with Wi-Fi Direct or Miracast.
Select [Refresh] on the Miracast/Wi-Fi Direct Mode screen and then try connecting again.
• Turn off power (to stand-by mode) once then turn power back on.
• Insert a thin rod into the reset button on the front side of the main body then reset the unit.
Only mobile devices that are compliant with Miracast are supported. Ask the manufacturer of the corresponding device whether the mobile
device is compliant with Miracast.
RETURN on the remote control to close the Miracast/Wi-
Problem Check Remedy
The audio or video is interrupted (distorted) when using DRM, Wi-Fi Direct, or Miracast.
Is there a microwave oven or other device that generates electromagnetic waves near the unit?
Are the mobile device and unit far away from each other or is there an object between them?
Improve the wireless LAN environment by taking steps such as moving the unit and mobile devices etc. closer together.
• Use the unit in a place away from microwave ovens or others device generating electromagnetic waves.
• Avoid using devices generating electromagnetic waves as much as possible when using the unit with a wireless LAN.
When using wireless LAN, Wi-FI Direct or Miracast, depending on the environment (radiowave interference) during sending/receiving of a large volume of data such as HD quality image files and WAV 192 kHz/ 24 bit high quality audio files, images and sound may be interrupted during playback.
Others
Problem Check Remedy
Power does not turn on. Is the power cord properly
The player’s power turns off automatically.
The player’s power turns on automatically.
This unit cannot be operated. • Use within the specified usage temperature range (page 61).
The player cannot be operated with the remote control.
Unit heats up during use. Depending on the usage environment, the temperature of the unit's
Input of the connected TV and AV system switches automatically.
Settings I have made have been cleared.
connected?
Is Auto Power Off set to 10 min/20 min/30 min?
Is Control set to On? The player’s power may turn on together with the power of the TV
Are you operating the remote control from a point too far away from the player?
Are the batteries dead? Replace the batteries (page 7).
Is Control set to On? The input of the TV and AV system (AV receiver or amplifier, etc.)
• Have you disconnected the power cord while the player’s power was on?
• Has there been a power failure?
• Plug the power cord securely into the power outlet (page 20).
• Unplug the power cord, wait several seconds, then plug the power cord back in.
If Auto Power Off is set to 10 min/20 min/30 min, the player’s power automatically turns off if no operation is performed for the set amount of time (page 40).
connected to the HDMI OUT terminal. If you do not want the player’s power to turn on when the TV’s power is turned on, set Control to Off (page 39).
• If the power cannot be turned off (to standby), reset the unit. Use a thin rod to press the reset button on the main unit’s front panel. The unit restarts and can now be operated.
Operate from within 7 m of the remote control sensor.
cabinet may increase somewhat during use, but this is not a malfunction and there is no need to worry.
connected to the HDMI OUT terminal may automatically switch to the player when playback starts on the player or the menu screen (Home Media Gallery, etc.) is displayed. If you do not want the inputs of the connected TV and AV system (AV receiver or amplifier, etc.) to switch automatically, set Control to Off (page 39).
Always press STANDBY/ON on the player’s front panel or STANDBY/ON on the remote control and check that POWER OFF has turned off from the player’s front panel display before disconnecting the power cord. Be particularly careful when the power cord is connected to the AC outlet on another device because the player turns off in conjunction with the device.
08
57
En
Problem Check Remedy
08
USB (external storage) device does not work with this player properly.
Is the USB device properly connected?
Is the USB device connected via an extension cable?
Is the external storage device connected to the USB port via a memory card reader or USB hub?
Does the external storage device contain multiple partitions?
Is the external storage device write-protected?
Is the USB device’s file system FAT32, FAT16 or NTFS?
• Turn the player’s power off, then turn the power back on.
• Turn the player’s power off, then reconnect the external storage device (page 19).
Do not use an extension cable. The player may not work properly with it.
External storage device may not work if connected to the USB port via a memory card reader or USB hub.
External storage devices may not be recognized if they contain multiple partitions.
Turn the player’s power off, then disable the write-protection.
USB devices formatted in the FAT32, FAT16 or NTFS file system can be used.
Some external storage devices may not operate.
58
En
Glossary
08
Angle (Multi angle)
Up to 9 camera angles can be recorded simultaneously on BD­ROM or DVD-Video discs, letting you view the same scene from different angles.
AVCHD (Advanced Video Codec High Definition)
See page 10.
BDAV
Of the BD format, the Audio Visual Format Specifications for HD digital broadcast recording is referred to as BDAV on this player and in these operating instructions.
BD-J
See page 10.
BD-LIVE
See page 10.
BDMV
Of the BD format, the Audio Visual Format Specifications designed for pre-packaged high definition (HD) movie contents is referred to as BDMV on this player and in these operating instructions.
BONUSVIEW
See page 9.
Deep Color
See page 16.
Default Gateway
A default gateway is a communication device such as a router which passes data between netw orks. It is used to direct data to networks on which the destination gateway is not explicitly specified.
DHCP (Dynamic Host Configuration Protocol)
This protocol provides configuration parameters (IP address, etc.) for computers and other devices connected to the network.
DivX
See page 11.
DNS (Domain Name System)
This is a system for associating Internet host names with IP addresses.
Dolby Digital
Dolby Digital is an audio format to record the sound in up to 5.1 channels with a fraction of the amount of data as compared to linear PCM audio signals.
Dolby Digital Plus
Dolby Digital Plus is an audio format for high-definition media. Built on Dolby Digital, it combines the efficiency and flexibility to provide high quality multi-channel audio. With BD-ROMs, up to
7.1 channels of digital sound can be recorded.
Dolby TrueHD
Dolby TrueHD is an audio format using lossless coding. With BD­ROMs, up to 8 channels can be recorded at 96 kHz/24 bits, or up to 6 channels at 192 kHz/24 bits.
DRM
A technology for protecting copyrighted digital data. Digitized videos, images and audio retain the same quality even when they are copied or transferred repeatedly. DRM is a technology for restricting the distribution or playback of such digital data without the authorization of the copyright holder.
DSD (Direct Stream Digital)
The Digital Audio encoding system found on SACDs, that expresses the audio signals by the pulse density of one bit data.
DTS Digital Surround
DTS Digital Surround is an audio format to record 48 kHz/24 bits audio signals in 5.1 channels.
DTS-HD High Resolution Audio
DTS-HD High Resolution Audio is an audio format using lossy coding. It can record 7.1 channels at 96 kHz/24 bits.
DTS-HD Master Audio
DTS-HD Master Audio is an audio format using lossless coding. With BD-ROMs, 7.1 channels can be recorded at 96 kHz/24 bits, or 5.1 channels at 192 kHz/24 bits.
Ethernet
A standard for local area networks (LANs) used to connect multiple computers, etc. in the same location. This player supports 100BASE-TX.
Frames and fields
A frame is the unit for one of the still pictures which compose motion pictures. One frame consists of a picture of odd lines and a picture of even lines called fields in video signal with interlaced scan method (576i, 1080i, etc.).
HDMI (High-Definition Multimedia Interface)
See page 16.
Interactive audio
The audio signals recorded in the titles of BD-ROMs. They include for example the clicking sound made when the menu screen is operated.
Interlaced scan
With this method, one picture is displayed by scanning it twice. The odd lines are displayed in the first pass, the even lines are displayed in the second, to form a single picture (frame). Interlaced scan is indicated in this player and operating instructions by an “i” after the resolution value (for example, 576i).
IP address
An address that identifies a computer or other device connected to the Internet or local area network. It is represented a number in four sections.
Linear PCM
This is referred as the audio signals that are not compressed.
59
En
MAC (Media Access Control) address
08
A hardware identification number assigned specifically to the network device (LAN card, etc.).
MPEG (Moving Picture Experts Group)
The name of a family of standards used to encode video and audio signals in a digital compressed format. The video encoding standards include MPEG-1 Video, MPEG-2 Video, MPEG-4 Visual, MPEG-4 AVC, etc. The audio encoding standards include MPEG­1 Audio, MPEG-2 Audio, MPEG-2 AAC, etc.
Multi-session
Multi-session/multi-border recording is a method of recording two or more sessions/borders on a single disc. When recording data on a disc, the unit comprising the data from the beginning to the end of that instance of recording is called a session or border.
Parental Lock
See page 42.
Picture-in-Picture (P-in-P)
This is a function for superimposing a sub video on the main video. Some BD-ROMs include secondary video, which can be superimposed on the primary video.
Port number
This is a sub-address provided below the IP address for simultaneously connecting to multiple parties during Internet communications.
Progressive scan
With this method, one picture is consisted of a single picture, without dividing it in two pictures. Progressive scan provides clear pictures with no flicker, in particular for still pictures that contain much text, graphics, or horizontal lines. Progressive scan is indicated in this pl ayer and operating instructions by a “p” a fter the resolution value (for example, 576p).
Proxy server
This is a relay server for ensuring fast access and safe communications when connecting to the Internet from an internal network.
Region number
See page 10.
Secondary audio
Some BD-ROMs include sub audio streams mixed with the main audio stream. These sub audio streams are called “secondary audio”. On some discs this secondary audio is recorded as the audio for the secondary video.
Secondary video
Some BD-ROMs include sub videos superimposed on the main videos using the Picture-in-Picture function. These sub videos are called “secondary video”.
Subnet mask
This is used to identify which part of the IP address corresponds to the subnet (a separately managed network). The subnet mask is expressed as ‘255.255.255.0’.
USB (Universal Serial Bus)
USB is the industry standard for connecting peripherals to PCs.
60
En
VC-1
A video codec developed by Microsoft and standardized by the Society of Motion Picture and Television Engineers (SMPTE). Some BDs include videos encoded in this codec.
x.v.Color
See page 16.
Specifications
08
Model BDP-80FD
Type
Rated voltage
Rated frequency 50 Hz/60 Hz
Power consumption 17 W
Power consumption (standby) 0.3 W
Power consumption (quick start) 5 W
Weight 2.0 kg
External dimensions (including projecting parts) 435 mm (W) x 58 mm (H) x 250 mm (D)
Tolerable operating temperature +5 °C to +35 °C
Tolerable operating humidity 5 % to 85 % (no condensation)
Output terminals
HDMI 1 set, 19-pin: 5 V, 250 mA
Audio outputs 2-channel (left/right) 1 set, RCA jacks
Audio output level 200 mVrms (1 kHz, –20 dB)
Frequency response 4 Hz to 88 kHz (192 kHz sampling)
Digital audio outputs Coaxial 1 set, RCA jacks
LAN 1 set, Ethernet jack (10BASE-T/100BASE-TX)
Wireless LAN (internal antenna) Integrated IEEE 802.11n (2.4 GHz band) wireless
USB 2 set, Type A
TM
Blu-ray 3D
AC 110 V to 240 V
networking access, compatible with 802.11b/g Wi-Fi networks
PLAYER
Note
• The specifications and design of this product are subject to change without notice.
• This item incorporates copy protection technology that is protected by U.S. patents and other intellectual property rights of Rovi Corporation. Reverse engineering and disassembly are prohibited. Do not connect the unit through a VCR. Video signals fed through VCRs may be affected by copyright protection systems and the picture will be distorted on the television.
• Corporation and product names mentioned herein are trademarks or registered trademarks of the respective corporations.
© 2014 PIONEER HOME ELECTRONICS CORPORATION. All rights reserved.
61
En
Nous vous remercions pour cet achat d’un produit Pioneer. Nous vous demandons de lire soigneusement ce mode d’emploi ; vous serez ainsi à même de faire fonctionner l’appareil correctement. Après avoir bien lu le mode d’emploi, le ranger dans un endroit sûr pour pouvoir s’y référer ultérieurement.
IMPORTANT
ATTENTION
DANGER D´ELECTROCUTION
NE PAS OUVRIR
Ce symbole de l’éclair, placé dans un triangle équilatéral, a pour but d’attirer l’attention de l’utilisateur sur la présence, à l’intérieur du coffret de l’appareil, de “tensions dangereuses” non isolées d’une grandeur suffisante pour représenter un risque d’électrocution pour les êtres humains.
ATTENTION :
POUR ÉVITER TOUT RISQUE D’ÉLECTROCUTION, NE PAS ENLEVER LE COUVERCLE (NI LE PANNEAU ARRIÈRE). AUCUNE PIÈCE RÉPARABLE PAR L’UTILISATEUR NE SE TROUVE À L’INTÉRIEUR. CONFIER TOUT ENTRETIEN À UN PERSONNEL QUALIFIÉ UNIQUEMENT.
Ce point d’exclamation, placé dans un triangle équilatéral, a pour but d’attirer l’attention de l’utilisateur sur la présence, dans les documents qui accompagnent l’appareil, d’explications importantes du point de vue de l’exploitation ou de l’entretien.
D3-4-2-1-1b_A1_Fr
ATTENTION
Cet appareil est un produit laser de Classe 1, classé selon l’article IEC 60825-1:2007 relatif à la Sécurité des produits laser, mais la diode laser qu’il renferme est supérieure à la Classe 1. Pour garantir une sécurité constante, ne retirez aucun des couvercles et n’essayez pas d’avoir accès à l’intérieur de l’appareil. Confiez toute réparation à un personnel qualifié.
APPAREIL À LASER DE CLASSE 1
L’étiquette suivante se trouve sur votre appareil. Emplacement : à l’intérieur de l’appareil
D58-5-2-2b*_B1_Fr
AVERTISSEMENT
Cet appareil n’est pas étanche. Pour éviter les risques d’incendie et de décharge électrique, ne placez près de lui un récipient rempli d’eau, tel qu’un vase ou un pot de fleurs, et ne l’exposez pas à des gouttes d’eau, des éclaboussures, de la pluie ou de l’humidité.
Ce produit est destiné à une utilisation domestique générale. Toute panne due à une utilisation autre qu'à des fins privées (comme une utilisation à des fins commerciales dans un restaurant, dans un autocar ou sur un bateau) et qui nécessite une réparation sera aux frais du client, même pendant la période de garantie.
D3-4-2-1-3_A1_Fr
K041_A1_Fr
AVERTISSEMENT
Pour éviter les risques d’incendie, ne placez aucune flamme nue (telle qu’une bougie allumée) sur l’appareil.
D3-4-2-1-7a_A1_Fr
PRÉCAUTION DE VENTILATION
Lors de l’installation de l’appareil, veillez à laisser un espace suffisant autour de ses parois de manière à améliorer la dissipation de chaleur (au moins 10 cm sur le dessus, 10 cm à l’arrière et 10 cm de chaque côté).
AVERTISSEMENT
Les fentes et ouvertures du coffret sont prévues pour la ventilation, pour assurer un fonctionnement stable de l’appareil et pour éviter sa surchauffe. Pour éviter les risques d’incendie, ne bouchez jamais les ouvertures et ne les recouvrez pas d’objets, tels que journaux, nappes ou rideaux, et n’utilisez pas l’appareil posé sur un tapis épais ou un lit.
D3-4-2-1-7b*_A1_Fr
Milieu de fonctionnement
Température et humidité du milieu de fonctionnement : De +5 °C à +35 °C (de +41 °F à +95 °F) ; Humidité relative inférieure à 85 % (orifices de ventilation non obstrués) N’installez pas l’appareil dans un endroit mal ventilé ou un lieu soumis à une forte humidité ou en plein soleil (ou à une forte lumière artificielle).
ATTENTION
L’interrupteur
STANDBY/ON de cet appareil ne coupe pas complètement celui-ci de sa prise secteur. Comme le cordon d’alimentation fait office de dispositif de déconnexion du secteur, il devra être débranché au niveau de la prise secteur pour que l’appareil soit complètement hors tension. Par conséquent, veillez à installer l’appareil de telle manière que son cordon d’alimentation puisse être facilement débranché de la prise secteur en cas d’accident. Pour éviter tout risque d’incendie, le cordon d’alimentation sera débranché au niveau de la prise secteur si vous prévoyez une période prolongée de non utilisation (par exemple avant un départ en vacances).
D3-4-2-1-7c*_A1_Fr
D3-4-2-2-2a*_A1_Fr
NOTE IMPORTANTE SUR LE CABLE D’ALIMENTATION
Tenir le câble d’alimentation par la fiche. Ne pas débrancher la prise en tirant sur le câble et ne pas toucher le câble avec les mains mouillées. Cela risque de provoquer un court-circuit ou un choc électrique. Ne pas poser l’appareil ou un meuble sur le câble. Ne pas pincer le câble. Ne pas faire de noeud avec le câble ou l’attacher à d’autres câbles. Les câbles d’alimentation doivent être posés de façon à ne pas être écrasés. Un câble abîmé peut provoquer un risque d’incendie ou un choc électrique. Vérifier le câble d’alimentation de temps en temps. Contacter le service après-vente PIONEER le plus proche ou le revendeur pour un remplacement.
S002*_A1_Fr
Précaution concernant les ondes radio
Cet appareil utilise comme onde radio une fréquence de 2,4 GHz, c’est-à-dire une bande utilisée par d’autres systèmes sans fil (Fours à micro-ondes, téléphones sans fil, etc.). Si des parasites apparaissent sur les images télévisées, il est possible que cet appareil (y compris ceux qu’il prend en charge) provoquent des interférences sur le connecteur d’entrée de votre téléviseur, les images vidéo, le tuner satellite, etc. Dans ce cas, augmentez la distance entre la prise d’entrée d’antenne et cet appareil (y compris les produits pris en charge par cet appareil).
• Pioneer n’est pas responsable d’un mauvais fonctionnement du produit Pioneer compatible due à une erreur/défaillance de la connexion réseau et/ou de l’appareil raccordé. Veuillez contacter votre fournisseur de service Internet ou le fabricant du périphérique du réseau.
• Un abonnement payant auprès d’un fournisseur d’accès Internet est nécessaire pour utiliser Internet.
Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un environnement non contrôlé et respecte les règles d’exposition aux fréquences radioélectriques (RF) CNR-102 de l’IC. Cet équipement doit être installé et utilisé en gardant une distance de 20 cm ou plus entre le dispositif rayonnant et le corps (à l’exception des extrémités : mains, poignets, pieds et chevilles).
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
D8-9-2-7-4_A1_Fr
D8-9-10-1_A1_Fr
Condensation
Si vous transportez sans transition le lecteur d’un endroit froid dans un pièce chaude (en hiver, par exemple), ou si la température de la pièce où se trouve le lecteur augmente rapidement, des gouttelettes d’eau (condensation) peuvent se former à l’intérieur du lecteur (sur les pièces et la lentille). En cas de condensation, le lecteur ne fonctionne pas correctement et la lecture n’est pas possible. Laissez le lecteur en service pendant 1 ou 2 heures à la température ambiante (pour que l’humidité ait le temps de s’évaporer). Les gouttelettes d’eau se dissiperont et la lecture sera de nouveau possible. De la condensation peut aussi se former en été si le lecteur est exposé à l’air d’un climatiseur. Dans ce cas, éloignez le lecteur du climatiseur.
S005_A1_Fr
La protection de votre ouïe est entre vos mains
Pour assurer le rendement optimal de votre matériel et – plus important encore – la protection de votre ouïe, réglez le volume à un niveau raisonnable. Pour ne pas altérer votre sens de la perception, le son doit être clair mais ne produire aucun vacarme et être exempt de toute distorsion. Votre ouïe peut vous jouer des tours. Avec le temps, votre système auditif peut en effet s’adapter à des volumes supérieurs, et ce qui vous semble un « niveau de confort normal » pourrait au contraire être excessif et contribuer à endommager votre ouïe de façon permanente. Le réglage de votre matériel à un volume sécuritaire AVANT que votre ouïe s’adapte vous permettra de mieux vous protéger.
CHOISISSEZ UN VOLUME SÉCURITAIRE:
• Réglez d’abord le volume à un niveau inférieur.
• Montez progressivement le volume jusqu’à un niveau d’écoute confortable ; le son doit être clair et exempt de distorsions.
• Une fois que le son est à un niveau confortable, ne touchez plus au bouton du volume.
N’OUBLIEZ PAS DE RESPECTER LES DIRECTIVES SUIVANTES:
• Lorsque vous montez le volume, assurez-vous de pouvoir quand même entendre ce qui se passe autour de vous.
• Faites très attention ou cessez temporairement l’utilisation dans les situations pouvant s’avérer dangereuses.
• N’utilisez pas des écouteurs ou un casque d’écoute lorsque vous opérez un véhicule motorisé ; une telle utilisation peut créer des dangers sur la route et est illégale à de nombreux endroits.
S001a_A1_Fr
Précautions concernant le visionnage en 3D
Si vous ressentez une fatigue ou une gêne pendant le visionnage d’images en 3D, cessez de les
regarder.
Les enfants, en particulier ceux de moins de 6 ans, sont plus sensibles à la fatigue et les personnes en
charge doivent surveiller tout signe de fatigue ou de gêne.
Pendant le visionnage d’images en 3D, faites régulièrement des pauses. Le visionnage prolongé d’images en 3D sans pause peut causer de la fatigue et un inconfort.
Contenu
01 Avant de commencer
Contenu du carton d’emballage . . . . . . . . . . . . . . . . . . . . . . .5
Mise en place des piles dans la télécommande. . . . . . . . .5
Mise à jour du logiciel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
À propos du fonctionnement de ce lecteur avec un dispositif
mobile (iPod, iPhone, iPad, etc.). . . . . . . . . . . . . . . . . . . . . . . 5
Types de disques/fichiers lisibles . . . . . . . . . . . . . . . . . . . . . . 6
Disques lisibles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Fichiers lisibles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Noms et fonctions des éléments. . . . . . . . . . . . . . . . . . . . . .12
Télécommande. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Face avant. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Panneau arrière . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
02 Raccordements
Quand un câble HDMI est utilisé . . . . . . . . . . . . . . . . . . . . . 14
À propos de l’HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
À propos du contrôle par l’HDMI . . . . . . . . . . . . . . . . . . . . 15
Raccordement d’un téléviseur . . . . . . . . . . . . . . . . . . . . . .16
Raccordement d’un récepteur ou amplificateur AV. . . . . 16
Raccordement des câbles audio. . . . . . . . . . . . . . . . . . . . . . 17
Raccordement d’un récepteur ou amplificateur AV avec un
câble audio numérique coaxial . . . . . . . . . . . . . . . . . . . . .17
Raccordement d’un appareil au port USB. . . . . . . . . . . . . . 17
À propos des dispositifs USB . . . . . . . . . . . . . . . . . . . . . . . 17
Raccordement du dispositif USB. . . . . . . . . . . . . . . . . . . . 17
Raccordement au réseau par l’interface LAN . . . . . . . . . . .18
Raccordement avec un câble LAN
(réseau LAN filaire) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Connexion à un réseau LAN sans fil . . . . . . . . . . . . . . . . .18
Raccordement du cordon d’alimentation . . . . . . . . . . . . . . 18
03 Pour commencer
Paramétrage à l’aide du menu Setup Navigator . . . . . . . . .19
04 Playback
Lecture de disques ou de fichiers. . . . . . . . . . . . . . . . . . . . .20
Vue rapide (Vue rapide avec audio) . . . . . . . . . . . . . . . . . .20
Recherche avant et arrière . . . . . . . . . . . . . . . . . . . . . . . . .21
Lecture de chapitres, de plages ou de fichiers
particuliers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Saut de contenu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Pour revenir à une position peu de
temps auparavant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Pour avancer à une position légèrement en avant. . . . . . 21
Lecture au ralenti. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Lecture avant et arrière pas à pas . . . . . . . . . . . . . . . . . . .21
Lecture répétée d’un passage précis d’un titre ou d’une
plage (Répétition A-B) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Répétition de la lecture (Lecture répétée). . . . . . . . . . . . .22
Lecture dans l’ordre souhaité
(Lecture programmée). . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Pose de signets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Lecture de photos en diaporama . . . . . . . . . . . . . . . . . . . .23
Changement de l’angle de prise de vues. . . . . . . . . . . . . .23
Changement des sous-titres. . . . . . . . . . . . . . . . . . . . . . . . 23
Sous-titres mobiles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Changement du son . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Commutation de la zone de lecture CD/SACD . . . . . . . . . 24
Affichage des informations du disque. . . . . . . . . . . . . . . . 24
Utilisation de BONUSVIEW ou de BD-LIVE. . . . . . . . . . . .24
Fonctions de lecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Utilisation du menu FUNCTION . . . . . . . . . . . . . . . . . . . . . .26
Lecture à partir d’un temps précis
(Recherche temporelle). . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Lecture d’un titre, d’un chapitre, d’une plage ou
d’un fichier particulier (Recherche). . . . . . . . . . . . . . . . . . 27
Lecture d’une plage particulière de disques, de titres ou
d’un chapitre (plage/fichier) dans un ordre aléatoire. . . . 27
Continuation de la lecture à partir de la position spécifiée
4
(Poursuite du visionnage) . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Fr
05 Lecture avec Home Media Gallery
À propos de Home Media Gallery. . . . . . . . . . . . . . . . . . . . . 28
À propos de la lecture en réseau. . . . . . . . . . . . . . . . . . . . 28
Lecture de fichiers sur le réseau . . . . . . . . . . . . . . . . . . . . . 29
Lecture de disque/USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Lecture de fichiers photo . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Lecture dans l’ordre souhaité (Playlist) . . . . . . . . . . . . . . . . 30
Ajout de plages ou de fichiers . . . . . . . . . . . . . . . . . . . . . . 30
Lecture de la Playlist. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Suppression de plages ou fichiers de la Playlist . . . . . . . 30
Connexion par Miracast
À propos de la Wi-Fi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Utiliser les fonctions’ Miracast/
Wi-Fi Direct de l’appareil . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Affichage de l’écran du mode Miracast/Wi-Fi Direct. . . . 31
Connexion par Miracast . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Connexion à un appareil non compatible avec Miracast/
Wi-Fi Direct . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Connexion par WPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Changez le SSID et le mot de passe . . . . . . . . . . . . . . . . . 32
Annuler la connexion Miracast/Wi-Fi Direct. . . . . . . . . . . 33
Lecture des fichiers photo, musicaux ou vidéo du dispositif
mobile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
06 Lecture de contenus web
Contenus web disponibles . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Lecture de contenus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
07 Réglages détaillés
Changement des réglages . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Utilisation de la page Configuration initiale . . . . . . . . . . . 35
Mise à jour du logiciel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Rétablissement des réglages par défaut du lecteur . . . . 42
Connexion sans fil au réseau . . . . . . . . . . . . . . . . . . . . . . . . 42
Réglage de la connexion sans fil au réseau . . . . . . . . . . . 42
Configuration WPS (Wi-Fi Protected Setup) . . . . . . . . . . . . 43
Réglage de la connexion WPS. . . . . . . . . . . . . . . . . . . . . . 43
À propos des formats audio numériques restitués. . . . . . . 44
Tableau des codes de langues et Tableau des codes de
pays et régions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Tableau des codes de langues. . . . . . . . . . . . . . . . . . . . . . 45
Tableau des codes de pays et régions. . . . . . . . . . . . . . . . 45
08 Informations supplémentaires
Précautions d’emploi. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Déplacement du lecteur . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Emplacement du lecteur . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Éteignez le lecteur lorsque vous ne l’utilisez pas. . . . . . . 46
Condensation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Nettoyage du lecteur. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Attention si lecteur est installé dans un meuble avec une
porte en verre. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Nettoyage de la lentille du capteur . . . . . . . . . . . . . . . . . . 47
Manipulation des disques . . . . . . . . . . . . . . . . . . . . . . . . . 47
En cas de panne. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Lecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Contrôle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Réseau . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
LAN sans fil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Divers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Glossaire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Spécifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
TM
/Wi-Fi DirectTM. . . . . . . . . . . . . . 31
Chapitre 1
Avant de commencer
Contenu du carton d’emballage
• Télécommande x 1
• Batteries au manganèse de taille AAA 700 x 2
• Cordon d’alimentation
•Carte de garantie
• Notice de la licence du logiciel
• Mode d’emploi (ce manuel)
Mise en place des piles dans la télécommande
Les piles fournies avec le lecteur servent avant tout à s’assurer du bon fonctionnement de ce produit et peuvent ne pas durer très longtemps. Il est conseillé d’utiliser des piles alcalines qui ont une meilleure autonomie.
AVERTISSEMENT
• N’utilisez pas ou ne rangez pas les piles en plein soleil ou à un endroit très chaud, comme dans une voiture ou près d’un appareil de chauffage. Les piles risqueraient de fuir, de surchauffer, d’exploser ou de s’enflammer. Ceci pourrait également réduire leur durée de vie ou leur performance.
Attention
• Ne pas utiliser une batterie neuve avec une batterie ancienne.
• Insérez les piles dans la télécommande en les orientant correctement, comme indiqué par les symboles de polarité ( et ).
• Lorsque vous insérez les piles, faites attention de ne pas endommager les ressorts sur les bornes de piles. Les piles pourraient fuir ou chauffer.
• N’exposez pas les piles à la chaleur, ne les ouvrez pas ou ne les jetez pas au feu ou dans l’eau.
• La tension des piles peut être différente, même si les piles semblent identiques. N’utilisez pas différents types de piles.
• Pour éviter toute fuite d’électrolyte, retirez les piles si vous prévoyez de ne pas utiliser la télécommande pendant un certain temps (1 mois ou plus). Si une pile devait fuir, essuyez soigneusement l’intérieur du logement puis insérez des piles neuves. Si le liquide d’une pile devait fuir et se répandre sur votre peau, lavez-le immédiatement avec une grande quantité d’eau.
• Lorsque vous mettez des piles usées au rebut, veuillez vous conformer à la réglementation gouvernementale ou environnementale en vigueur dans votre pays ou région.
1 Ouvrez le couvercle arrière. 2 Insérez les batteries (2 x taille AAA 700) qui sont
fournies.
Insérer d’abord à partir du côté .
3 Fermez le couvercle arrière.
Fermez bien le couvercle (vous devez entendre un clic).
À propos de la fonction limitant l’accès
aux informations nuisibles sur Internet
• Cet appareil présente une fonction qui restreint l’affichage des contenus web, etc. qui ne doivent pas être vus par les enfants ou d’autres personnes.
• Pour utiliser cette fonction, les réglages Internet doivent être changés (page 38).
Mise à jour du logiciel
Vous trouverez plus d’informations au sujet de ce lecteur sur le site Pioneer. Consultez ce site pour toute information sur la mise à jour et les services relatifs à votre lecteur Blu-ray disc.
http://www.pioneerelectronics.com
À propos du fonctionnement de ce lecteur avec un dispositif mobile (iPod, iPhone, iPad, etc.)
L’installation de l’application appropriée sur un dispositif mobile permet d’agir sur le lecteur depuis le dispositif mobile.
Pour le détail, reportez-vous aux informations produit sur le site Pioneer.
Cette application spéciale peut être changée ou arrêtée sans avis préalable.
01
5
Fr
Types de disques/fichiers lisibles
01
Disques lisibles
Les disques portant les logos suivants sur l’étiquette, le carton ou la jaquette peuvent être lus.
Attention
• Attention seuls les disques finalisés peuvent être lus.
Type de disque Logo
BD-ROM 
2
BD
BD-R
BD-RE 
DVD-ROM 
BDMV BDAV

Format de l’application
DVD-
Vidéo
DVD VR
CD-DA
DTS-CD
DATA-
DISC
1
DVD
CD
1. Disques sur lesquels des fichiers vidéo, photo ou audio sont enregistrés.
2. Disques double couche compris.
3. Les finaliser avant de les lire sur ce lecteur.
4. Les disques DVD-R pour création (3,95 Go et 4,7 Go) ne peuvent pas être lus.
5. Format AVCHD compris.
6. Format AVCREC compris.
7. Les disques DVD-RW Version 1.0 ne peuvent pas être lus.
8. CD vidéo compris.
«Blu-ray Disc», «Blu-ray» et le logo «Blu-ray Disc»
sont des marques commerciales de la Blu-ray Disc
6
Association.
Fr
2,3,4
DVD-R
3,7
DVD-RW
2,3
DVD+R
3
DVD+RW
CD-DA
8
(CD audio)
3
CD-R
3
CD-RW
CD-ROM 





5
5
6
6
 
 
est une marque commerciale de DVD
Format/Logo Licensing Corporation.
Disques illisibles
• HD DVD
• Disques DVD-RAM
Il est possible que certains disques ne figurant pas dans la liste ci-dessus ne puissent pas non plus être lus.
Remarque
• Certains disques ne pourront pas être lus bien qu’ils portent un des logos de la page précédente.
• Pour lire un disque de 8 cm, posez le disque dans le renfoncement destiné aux disques de 8 cm au centre du tiroir à disque. Aucun adaptateur n’est nécessaire. Les BD-ROM de 8 cm ne peuvent pas être lus.
À propos de la lecture de copies non autorisées
Avis de Cinavia
Ce produit utilise la technologie Cinavia pour limiter la copie non autorisée de certains films et certaines vidéos du commerce ainsi que de leurs pistes son. Lorsque l’emploi prohibé d’une copie non autorisée est détecté, un message s’affiche et la lecture ou la copie est interrompue.
Vous trouverez plus d’informations sur la technologie Cinavia auprès du Cinavia Online Consumer Information Center sur le site http://www.cinavia.com. Pour obtenir plus d’informations sur Cinavia par courrier, envoyez une carte postale avec votre adresse postale à : Cinavia Consumer Information Center, P.O. Box 86851, San Diego, CA, 92138, USA.
Copyright 2004-2010 Verance Corporation. Cinavia™ est une marque commerciale de Verance Corporation. Protégé par le brevet U.S. N° 7,369,677 et des brevets mondiaux, homologués et en attente d’homologation, sous licence de Verance Corporation. Tous droits de reproduction et de traduction réservés.
À propos de la protection des droits d’auteur
Certains Blu-ray DiscsTM, DVD et contenus diffusés par Internet ou d’autres réseaux sont protégés contre le piratage. La technologie antipiratage restreint la lecture et la sortie analogique. En raison des mises à jour des dispositions relatives à la protection des droits d’auteurs, les restrictions peuvent être différentes selon la date d’achat de ce produit. D’autre part, les restrictions peuvent être réactualisées lors de la mise à jour du logiciel après l’achat.
À propos des formats audio
Les formats audio suivants sont pris en charge par ce lecteur :
•Dolby TrueHD
•Dolby Digital Plus
•Dolby Digital
•DSD
•DTS-HD Master Audio
• DTS-HD High Resolution Audio
• DTS Digital Surround
•MPEG audio (AAC)
• PCM linéaire
Pour bénéficier du son ambiophonique des formats Dolby TrueHD, Dolby Digital Plus, DSD, DTS-HD Master Audio et DTS-HD High Resolution Audio, il est conseillé de raccorder le lecteur à un récepteur ou à un amplificateur AV compatible avec ces formats audio à l’aide d’un câble HDMI. Après avoir inséré un BD contenant des pistes son dans un de ces formats audio, sélectionnez le format audio sur le menu.
Fabriqué sous licence de Dolby Laboratories. Dolby et le symbole double-D sont des marques déposées de Dolby Laboratories.
Fabriqué sous licence sous couvert des brevets U.S. N° : 5,956,674; 5,974,380; 6,226,616; 6,487,535; 7,392,195; 7,272,567; 7,333,929; 7,212,872 et d’autres brevets U.S. et mondiaux, homologués et en attente d’homologation. DTS-HD, le Symbole et DTS-HD et le Symbole sont ensemble des marques déposées et DTS-HD Master Audio
|
Essential est une marque commerciale de DTS, Inc. Logiciel inclus dans ce produit. © DTS, Inc. Tous droits réservés.
Lecture de BD
• Les BD (BDMV) compatibles avec les formats suivants peuvent être lus.
– Disque Blu-ray Lecture seule (ROM) Format
Version 2 – Disque Blu-ray Enregistrable (R) Format Version 2 – Disque Blu-ray Réenregistrable (RE) Format
Version 3 Ce lecteur prend en charge les BD-ROM Profil 5.
“Blu-ray 3D” et le logo “Blu-ray 3D” sont des marques commerciales de la Blu-ray Disc Association.
Les fonctions BONUSVIEW, comme la lecture d’une image secondaire (Image dans l’image) et d’un son secondaire, peuvent être utilisées. Les données utilisées avec les fonctions BONUSVIEW (les données de l’image secondaire (Image dans l’image) et du son secondaire) peuvent être sauvegardées dans la mémoire. Pour le détail sur la lecture d’une image secondaire et d’un son secondaire, reportez­vous à la notice du disque.
«BONUSVIEW» est une marque commerciale de Blu-ray Disc Association.
01
7
Fr
01
Vous pouvez utiliser les fonctions BD-LIVE, qui permettent de télécharger des bandes-annonces ou d’autres langues pour les dialogues et les sous-titres, et de jouer des jeux vidéo en ligne, via Internet. Les données téléchargées grâce à la fonction BD-LIVE (bandes-annonces, etc.) sont sauvegardées dans la mémoire. Reportez-vous aux instructions du disque pour le détail sur les fonctions BD-LIVE.
Le logo «BD-LIVE» est une marque commerciale de Blu-ray Disc Association.
Avec les BD-ROM, il est possible d’utiliser les applications BD-J (Java) pour créer des titres hautement interactifs, jeux compris.
Oracle et Java sont des marques déposées d’Oracle Corporation et/ou de ses affiliés. Tout autre nom mentionné peut correspondre à des marques appartenant à d’autres propriétaires qu’Oracle.
• Les BD (BDAV) compatibles avec les formats suivants peuvent être lus.
– Disque Blu-ray Enregistrable (R) Format Version 1 – Disque Blu-ray Réenregistrable (RE) Format
Version 2
Lecture de DVD
Cette étiquette indique que les disques DVD-RW enregistrés dans le format VR (format d’enregistrement vidéo) peuvent être lus. Toutefois, dans le cas de disques enregistrés avec un programme crypté pour un enregistrement unique, la lecture n’est possible qu’à l’aide d’un dispositif compatible avec le CPRM.
8
Fr
L’AVCHD est un format haute définition (HD) pour caméscope numérique permettant d’enregistrer sur certains supports en haute définition grâce à des technologies de compression extrêmement performantes.
«AVCHD» et le logo «AVCHD» sont des marques commerciales de Panasonic Corporation et de Sony Corporation.
À propos des codes régionaux
Des codes régionaux sont attribués aux lecteurs de disques Blu-ray et aux disques BD-ROM ou DVD-Vidéo en fonction de la région où ils sont commercialisés.
Les codes régionaux de ce lecteur sont les suivants :
•BD-ROM : A
• DVD-Vidéo : 1
Les disques ne contenant pas ces codes ne peuvent pas être lus. Les disques suivants peuvent être lus sur ce lecteur.
• BD : A (A compris) et ALL
• DVD : 1 (1 compris) et ALL
Lecture de CD
Au sujet de la copie de CD protégés : Ce lecteur se conforme aux spécifications du format CD audio. Il ne prend pas en charge la lecture ou les fonctions des disques non conformes à ces spécifications.
Lecture de DualDisc
Un DualDisc est un disque à deux faces dont une face renferme les données du DVD — vidéo, audio, etc. — et l’autre face les données non DVD, par exemple des matériaux audionumériques.
La face DVD d’un DualDisc peut être lue sur ce lecteur. La face audio, non DVD du disque ne peut pas être lue par
ce lecteur. Il est possible que lors du chargement ou de l’éjection
d’un DualDisc, la face opposée à la face de lecture soit rayée. La lecture d’un disque rayé n’est pas possible.
Pour tout complément d’informations sur les spécifications du DualDisc, consultez le fabricant du disque ou le magasin d’achat.
Lecture de disques créés sur un ordinateur ou un enregistreur de BD/ DVD
• Du fait des réglages de l’application ou de l’environnement de l’ordinateur, la lecture de disques enregistrés sur un ordinateur peut être impossible. Enregistrez vos disques dans un format lisible sur ce lecteur. Pour le détail, contactez votre revendeur.
• La lecture de disques enregistrés sur un ordinateur ou un enregistreur BD/DVD ne sera pas impossible, si les caractéristiques du disque, des éraflures, de la saleté sur le disque, de la saleté sur la lentille de l’enregistreur, etc. n’ont pas permis d’effectuer une gravure de qualité.
À propos des dossiers et des fichiers vidéo, audio et photo
Les fichiers audio et photo peuvent être lus sur ce lecteur si les dossiers du disque ou du dispositif USB sont créés de la façon suivante.
Exemple de la structure de dossiers :
Dossier
001.jpg/001.mp3
xxx.jpg/xxx.mp3
Dossier 01
Dossier XX
*
Dossier
001.jpg/001.mp3
xxx.jpg/xxx.mp3
001.jpg/001.mp3
xxx.jpg/xxx.mp3
*
001.jpg/001.mp3
xxx.jpg/xxx.mp3
*
*
* Le nombre de dossiers et de fichiers dans un seul dossier (dossier principal compris) se limite à 256. Ne créez pas plus de 5 niveaux de dossiers.
Remarque
• Les noms de fichiers et dossiers s’affichant sur ce lecteur peuvent être différents de ceux qui s’affichent sur l’ordinateur.
Fichiers lisibles
Les fichiers vidéo, photo et audio enregistrés sur des BD, DVD, CD ou des dispositifs USB peuvent être lus.
Formats de fichiers vidéo pris en charge
•DivX Plus HD
DivX Certified DivX Plus 1080p HD, contenu facturé compris.
À PROPOS DE LA VIDÉO DIVX : DivX vidéo numérique créé par DivX, LLC, qui est une filiale de Rovi Corporation. Ceci est un appareil DivX Certified divx.com pour plus d’informations sur les outils logiciels permettant de convertir vos fichiers en vidéos DivX.
®
pour la lecture de vidéos DivX® et
TM
HD (H.264/MKV) d’un maximum de
®
est un format
®
officiel qui lit la vidéo DivX. Visitez le site
À PROPOS DE LA VIDÉO DIVX À LA DEMANDE : Cet appareil certifié DivX
®
doit être enregistré afin de pouvoir lire des vidéos DivX à la demande (VOD). Pour obtenir votre code d’enregistrement, localisez la section VOD DivX dans utilisation des menus. Allez sur le site vod.divx.com pour savoir comment terminer votre enregistrement.
TM
DivX®, DivX Certified®, DivX Plus
HD et les logos associés sont des marques commerciales de Rovi Corporation ou de ses filiales et sont utilisés sous licence.
Remarque
®
• Cet appareil DivX
Certified doit être enregistré pour pouvoir lire des vidéos à la demande DivX (VOD). Obtenez d’abord le code d’enregistrement VOD DivX de votre appareil et spécifiez-le lors de votre enregistrement. Important : Les vidéos VOD DivX sont protégées par un système DivX DRM (Gestion numérique des droits) qui restreint la lecture aux appareils certifiés DivX immatriculés. Si vous essayez de lire une vidéo VOD DivX non autorisée pour votre appareil, le message Erreur d’autorisation apparaîtra et la vidéo ne pourra pas être vue. Consultez le site www.divx.com/vod pour plus d’informations.
– Le code d’enregistrement DivX VOD de ce lecteur
peut être vérifié dans HOME MENU
Configuration initiale Lecture DivX
®
DRM Code d’enregistrement (page 38).
– Le nombre de visionnages est limité pour certains
fichiers VOD DivX. Lorsque vous regardez ces fichiers sur votre lecteur, le nombre restant de visionnages est indiqué. Les fichiers pour lesquels le nombre de visionnages restants indique 0 ne peuvent pas être lus (Cette location Divx a expiré s’affiche). Les fichiers pour lesquels le nombre de visionnage n’est pas limité peuvent être visionnés à volonté (le nombre restant de visionnages n’apparaît pas).
• YouTube
TM
YouTube
est une marque commerciale de Google
Inc.
01
VOD
9
Fr
Tableau de fichiers lisibles
01
Fichiers lisibles
(Extensions)
MP3 (.mp3)
2
WMA (.wma)
3
AAC (.m4a)
WAV (.wav)
FLAC (.flac)
Monkey’s Audio (.ape)
JPEG (.jpg/.jpeg)
MPO (.mpo)
PNG (.png)
GIF (.gif)
DivX (.avi/.divx/.mkv)
MP4 (.mp4)
WMV (.wmv)
BD-R/RE/-R DL/
RE DL/-R LTH,
DVD-R/RW/-R DL/
+R/+RW/+R DL,
CD-R/RW
Supports lisibles
1
Dispositifs USB






Résolution maximale : 4 000 x 3 000 pixels
Photo 3D





Network
Spécifications des fichiers
Fréquences d’échantillonnage : Jusqu’à 48 kHz Débit binaire : Jusqu’à 320 kbps Type audio : MPEG-1 Audio Layer 3
Fréquences d’échantillonnage : Jusqu’à 48 kHz Débit binaire : Jusqu’à 192 kbps Type audio : WMA version 9
Fréquences d’échantillonnage : Jusqu’à 96 kHz Débit binaire : Jusqu’à 192 kbps Type audio : MPEG4-AAC
Fréquences d’échantillonnage : Jusqu’à 192 kHz
Débit binaire de la quantification : 16 bits, 24 bits
Voie : 2 voies Fréquences d’échantillonnage : Jusqu’à
192 kHz Débit binaire de la quantification : 16 bits,
24 bits Voie : Multivoies
Fréquences d’échantillonnage : Jusqu’à 192 kHz
Débit binaire de la quantification : 16 bits Voie : 2 voies
Résolution maximale : 2 048 x 1 024 pixels Les fichiers PNG animés ne sont pas pris en
charge. Résolution maximale : 2 048 x 1 024 pixels
Les fichiers GIF animés ne sont pas pris en charge.
La rotation n’est pas prise en charge.
Versions prises en charge : Jusqu’à DivX PLUS HD
Résolution maximale : Jusqu’à 1 920 x 1 080 (DivX
Jusqu’à 1 280 x 720 (MKV) Résolution maximale : Jusqu’à 1 920 x 1 080
Vidéo : MPEG4, MPEG-4 AVC (niveau 4.1) Audio : AAC, MP3
Résolution maximale : Jusqu’à 1 280 x 720 Vidéo : WMV9, WMV9AP (VC-1) Audio : WMA
®
PLUS HD)
®
10
Fr
Supports lisibles
Fichiers lisibles
(Extensions)
AVI (.avi)
3GP (.3gp)
FLV (.flv)
1. Cet appareil prend en charge les systèmes de fichiers FAT16, FAT32 et NTFS.
2. WMA Pro, Lossless and Voice ne sont pas pris en charge.
3. Le codage sans perte Apple n’est pas pris en charge.
BD-R/RE/-R DL/
RE DL/-R LTH,
DVD-R/RW/-R DL/
+R/+RW/+R DL,
CD-R/RW



Dispositifs USB
1
Network
Spécifications des fichiers
Résolution maximale : Jusqu’à 1 920 x 1 080 Vidéo : MPEG4 Audio : MP3, AAC
Vidéo : H.263, MPEG4, H.264 Audio : MPEG-4 AAC
Vidéo : Sorenson H.263 (FLV1), VP6 (FLV4), H.264
Audio : MP3, AAC
Remarque
• Selon la structure des fichiers, la capacité du serveur et la configuration du réseau, il peut être impossible de lire certains fichiers, même s’ils sont mentionnés dans le tableau des fichiers lisibles ci-dessus.
• Avec des connexions LAN sans fil, en fonction de l’environnement d’utilisation (interférences radio, etc.), l’image ou le son peuvent être interrompus pendant la lecture de fichiers vidéo à haute qualité d’image (tels que des fichiers de qualité HD) ou des fichiers musicaux à haute qualité sonore (tels que les fichiers WAV 192 kHz/24 bits) en raison de la quantité importante de données qui doivent être transférées.
• Les fichiers protégés par le DRM (Digital Rights Management) ne peuvent pas être lus (fichiers DivX VOD non compris).
• Les contenus AVCHD ne peuvent pas être lus par le réseau.
01
11
Fr
Noms et fonctions des éléments
01
Télécommande
10 STOP – (page 20)
1 2
3 4 5
6
7 8
9 10 11
12
13
14
15
16
17
1 STANDBY/ON – Pour allumer et éteindre. 2CONTINUED – Pour continuer la lecture à partir d’un
point précis. (page 27)
3 AUDIO – (page 24) 4 SUBTITLE – (page 23) 5CD/SACD – Pour les disques hybrides, pour basculer
entre les couches CD et SACD. (page 24)
6 REPEAT – (page 22) 7A-B – (page 21) 8 YouTube – Pour voir des vidéos sur YouTube.
(page 34)
12
9 – (page 21)
Fr
18
19 20 21
22
23
24
25
26
27
28
29
30
11 REV – (page 21) 12 TOP MENU – Pour afficher la première page du
13 /// – Pour sélectionner des éléments, changer
14 HOME MENU – (page 35)
15 Touches couleur – Pour naviguer sur les menus du
16 Touches numériques – Pour sélectionner et lire le
17 CLEAR – Pour effacer un nombre, etc. 18 OPEN/CLOSE – Pour ouvrir et fermer le tiroir à
19 DISPLAY – (page 24) 20 Miracast – Affichage de l’écran du mode Miracast/
Wi-Fi Direct. (page 31)
21 FL DIMMER – À chaque pression, la luminosité de
22 SHORT SKIP – Appuyez pendant la lecture pour
avancer à une position 30 secondes après. (page 21) 23 REPLAY – Appuyez pendant la lecture pour revenir à
une position 10 secondes avant. (page 21)
24 HDMI – Pour changer la résolution des signaux vidéo
25 // 26 – (page 20) 27 FWD – (page 21) 28 POP UP MENU/MENU – Pour afficher les menus des
29 RETURN – Pour revenir à la page précédente.
30 FUNCTION – (page 26)
menu d’un BD-ROM ou DVD-Vidéo.
des réglages et déplacer le curseur. ENTER – Pour exécuter l’élément sélectionné ou
valider un réglage qui a été changé, etc.
BD-ROM.
PROGRAM – (page 22) BOOK MARK – (page 22) ZOOM – (page 22) INDEX – (page 23)
titre/le chapitre/la plage que vous voulez voir ou écouter ainsi que les éléments des menus.
disque.
l’afficheur de la face avant change (4 niveaux).
sortant de la prise HDMI OUT (page 36).
– (page 21)
BD-ROM ou DVD-Vidéo.
Face avant
01
1 2 3 54 6 7 8
1 STANDBY/ON – Pour allumer et éteindre le
lecteur.
2 Tiroir à disque
3 Afficheur de la face avant 4 Bouton de réinitialisation – Si l’appareil ne peut pas
être éteint (mis en veille), utilisez une tige fine pour appuyer sur ce bouton. L’appareil est réinitialisé et peut de nouveau fonctionner.
5 Capteur de télécommande – Orientez la
télécommande vers le capteur, puis utilisez-la à moins de 7 m.
Le lecteur ne parviendra pas à capter les signaux de la télécommande si une lumière fluorescente se trouve à proximité. Dans ce cas, éloignez le lecteur de la lumière fluorescente.
Panneau arrière
2
1
4 5 63
9
6 OPEN/CLOSE – Pour ouvrir et fermer le tiroir à
disque.
7 – Pour arrêter la lecture. 8 Port USB – (page 17) 9 – Pour démarrer la lecture.
1 Prise DIGITAL OUT (COAXIAL) – (page 17) 2 Prises AUDIO OUT – (page 17) 3 Prise HDMI OUT – (page 14)
4 Prise LAN (10/100) – (page 18) 5 Port USB – (page 17) 6AC IN – (page 18)
13
Fr
Chapitre 2
02
Raccordements
Veillez à toujours éteindre les appareils et à débrancher le cordon d’alimentation de la prise secteur avant de raccorder un appareil ou de changer les liaisons.
Après le raccordement, effectuez les réglages dans le menu Guide de Configuration ou Configuration initiale selon le type de câble raccordé (page 19).
Reportez-vous aussi au mode d’emploi de l’appareil raccordé.
Quand un câble HDMI est utilisé
Les signaux audio et vidéo peuvent être transmis aux appareils compatibles HDMI sous forme de signaux numériques sans perte de la qualité sonore ou vidéo.
Remarque
• Effectuez les réglages dans le menu Guide de Configuration selon l’appareil compatible HDMI
raccordé (page 19).
• Selon le câble HDMI utilisé, les signaux vidéo 1080p peuvent ne pas être fournis.
À propos de l’HDMI
Ce lecteur intègre l’interface multimédia haute définition
®
).
(HDMI
Les termes HDMI et HDMI High-Definition Multimedia Interface ainsi que le logo HDMI sont des marques commerciales ou des marques déposées de HDMI Licensing, LLC aux États-Unis et dans d’autres pays.
Le lecteur prend en charge le format Deep Color. Les lecteurs classiques peuvent transmettre un signal vidéo avec une profondeur de couleur de 8 bits dans les formats YCbCr 4:4:4 ou RGB ; les lecteurs prenant en charge le format Deep Color peuvent transmettre un signal vidéo avec une profondeur de couleur supérieure à 8 bits pour chaque composante couleur. Il est donc possible d’obtenir des dégradés de couleur plus subtils lorsque ce lecteur est raccordé à un téléviseur compatible Deep Color est raccordé.
Ce produit est compatible avec le “x.v.Color” qui donne un spectre de couleurs plus étendu répondant aux spécifications xvYCC. Le spectre des couleurs étendu permet de restituer des couleurs naturelles et plus fidèles que jamais lors de la
14
lecture de signaux vidéo conformes aux normes “xvYCC”,
Fr
quand le lecteur est raccordé à un téléviseur “x.v.Color”, etc. “x.v.Color” est le nom promotionnel donné aux produits capables de restituer un spectre de couleurs plus étendu, répondant aux spécifications des standards internationaux définis comme xvYCC.
“x.v.Color” et sont des marques commerciales de Sony Corporation.
Signaux audio lisibles par la prise HDMI OUT
•Dolby TrueHD
•Dolby Digital Plus
•Dolby Digital
•DTS-HD Master Audio
• DTS-HD High Resolution Audio
• DTS Digital Surround
• PCM linéaire Des signaux audio PCM linéaires peuvent être
transmis s’ils remplissent les conditions suivantes : – Fréquence d’échantillonnage : 32 kHz à 192 kHz – Nombre de voies : 8 au maximum (6 au maximum
pour une fréquence d’échantillonnage de 192 kHz)
•DSD audio
• AAC
Lorsqu’un appareil DVI est raccordé
Il n’est pas possible de raccorder des appareils DVI (écrans d’ordinateur, par exemple) s’ils ne sont pas compatibles avec l’HDCP. L’HDCP est une
norme visant à protéger les contenus audiovisuels via l’interface DVI/HDMI.
• Aucun signal audio n’est restitué.
• Ce lecteur peut être raccordé à des appareils compatibles HDMI. Lorsqu’il est raccordé à un appareil DVI, et selon l’appareil DVI, il se peut qu’il ne fonctionne pas correctement.
À propos du contrôle par l’HDMI
Les fonctions sont opérantes lorsqu’un téléviseur ou un système AV Pioneer (récepteur ou amplificateur AV, etc.), compatible avec l’HDMI, est raccordé au lecteur à l’aide d’un câble HDMI.
Reportez-vous aussi au mode d’emploi du téléviseur et du système AV (récepteur ou amplificateur AV, etc.).
Pour utiliser le contrôle par l’HDMI
• Le contrôle par l’HDMI fonctionne dans la mesure où il est réglé sur Activé sur tous les appareils raccordés à l’aide de câbles HDMI.
• Lorsque vous avez relié et réglé tous les appareils, assurez-vous que l’image du lecteur apparaît bien sur le téléviseur. (Ceci est également nécessaire lorsque vous changez les appareils raccordés et rebranchez les câbles HDMI.) Le contrôle par l’HDMI n’agit peut­être pas correctement si l’image du lecteur ne s’affiche pas correctement sur le téléviseur.
• Utilisez des câbles HDMI voulez utiliser le contrôle par l’HDMI. Le contrôle par l’HDMI peut ne pas agir correctement si vous utilisez d’autres câbles HDMI.
• Sur certains modèles, le contrôle par l’HDMI est appelé “KURO LINK” ou “HDMI Control”.
• Le contrôle par l’HDMI n’opère pas avec les appareils d’autres marques, même si ce lecteur est raccordé par un câble HDMI.
Que permet le contrôle par l’HDMI
• Permet d’agir sur le lecteur avec la télécommande du téléviseur.
Certaines fonctions du lecteur, comme la marche et l’arrêt de la lecture et l’affichage des menus, peuvent être exécutées depuis le téléviseur.
• Afficher l’image du lecteur sur l’écran du téléviseur. (Sélection automatique)
L’entrée change automatiquement sur le téléviseur et le système AV (récepteur ou amplificateur AV, etc.) lorsque la lecture démarre sur le lecteur ou lorsque la page HOME MENU est affichée. Lorsque l’entrée change, l’image de lecture ou la page HOME MENU s’affiche sur le téléviseur.
• Allumer et éteindre le téléviseur et le lecteur. (Mise en service simultanée)
Si le téléviseur est éteint lorsque vous démarrez la lecture sur le lecteur ou affichez la page HOME MENU, il s’allumera automatiquement. Lorsque vous éteignez le téléviseur, le lecteur s’éteint automatiquement.
®/TM
haute vitesse si vous
Sound Retriever Link
À propos de la fonction Sound Retriever Link
La fonction Sound Retriever Link est une technologie visant à contrôler par l’HDMI la correction de la qualité des signaux audio compressés devant être restitués par le récepteur AV raccordé.
Cette fonction permet de restituer un son de plus grande qualité en activant automatiquement la correction sonore du récepteur AV raccordé.
La fonction Sound Retriever Link de ce lecteur agit essentiellement dans les situations suivantes.
• Lors de la lecture via un réseau ou lors de la lecture de contenus PC enregistrés sur un dispositif USB.
• Le récepteur AV Pioneer compatible avec la fonction Sound Retriever Link est raccordé à ce lecteur par un câble HDMI et le lecteur est réglé de la façon suivante (page 37).
Control : Activé
• Reportez-vous aussi aux instructions du récepteur AV.
• Consultez le site Pioneer pour les récepteurs AV compatibles avec la fonction Sound Retriever Link.
Attention
• Raccordez directement le lecteur au récepteur AV Pioneer compatible avec la fonction Sound Retriever Link. L’interruption d’une liaison directe avec un amplificateur ou un convertisseur AV (par exemple une coupure de l’HDMI) peut causer un dysfonctionnement.
Stream Smoother Link
À propos de la fonction Stream Smoother Link
La fonction Stream Smoother Link est une technologie visant à améliorer par l’HDMI la qualité de l’image des vidéos téléchargées d’un réseau. Cette fonction permet de bénéficier d’images de plus grande qualité, moins parasitées, en activant automatiquement la correction du flux du récepteur AV.
La fonction Stream Smoother Link de ce lecteur agit essentiellement dans les situations suivantes.
• Lors de la lecture via un service de distribution vidéo en réseau ou lors de la lecture de contenus PC enregistrés sur un support.
• Le récepteur AV Pioneer avec fonction Stream Smoother Link est raccordé à ce lecteur par un câble HDMI et le lecteur est réglé de la façon suivante (page 37). Reportez-vous aussi aux instructions du récepteur AV.
Control : Activé
Consultez le site Pioneer pour les récepteurs AV compatibles avec la fonction Stream Smoother Link.
Attention
• Raccordez directement le lecteur au récepteur AV Pioneer compatible avec la fonction Stream Smoother Link. L’interruption d’une liaison directe avec un amplificateur ou un convertisseur AV (par exemple une coupure de l’HDMI) peut causer un dysfonctionnement.
02
15
Fr
Raccordement d’un
02
téléviseur
Reportez-vous à
amplificateur AV
récepteur ou d’un amplificateur AV à l’aide d’un câble HDMI.
• Pour brancher et débrancher le câble, saisissez-le par la fiche.
• N’exercez pas de force sur la fiche qui puisse créer de faux contacts ou empêcher la sortie des signaux vidéo.
le commerce)
À la prise
d’entrée HDMI
Raccordement d’un récepteur ou
à la page 16 pour le raccordement d’un
Attention
Panneau arrière
(en vente dans
Câble HDMI
Un récepteur ou un amplificateur AV peut aussi être raccordé à l’aide d’un câble HDMI.
Téléviseur
Orientez correctement la fiche par rapp ort à la prise et insérez-la tout droit.
Sens du signal
Raccordement d’un récepteur ou amplificateur AV
Raccordez un récepteur ou un amplificateur AV pour bénéficier du son ambiophonique des formats Dolby TrueHD, Dolby Digital Plus, Dolby Digital, DTS-HD Master Audio, DTS-HD High Resolution Audio, DTS Digital Surround, LPCM, AAC ou DSD. Pour le détail sur le raccordement du téléviseur et des enceintes au récepteur ou à l’amplificateur AV, reportez-vous au mode d’emploi du récepteur ou de l’amplificateur AV.
Attention
• Pour brancher et débrancher le câble, saisissez-le par la fiche.
• N’exercez pas de force sur la fiche qui puisse créer de faux contacts ou empêcher la sortie des signaux vidéo.
Panneau arrière
(en vente dans
le commerce)
Câble HDMI
Orientez
correctement la
fiche par rapport à
À la prise
la prise et insérez-la
tout droit.
Téléviseur
Sens du signal
le commerce)
(en vente dans
Câble HDMI
À la prise
d’entrée HDMI
De la prise
de sortie
HDMI
Récepteur ou amplificateur
AV
d’entrée HDMI
16
Fr
Raccordement des câbles audio
Raccordement d’un récepteur ou amplificateur AV avec un câble audio numérique coaxial
Panneau arrière
Blanc
UT
Rouge
Câble audio numérique coaxial (en vente dans le commerce)
Sens du
signal
À la prise d’entrée audio numérique coaxiale
Récepteur ou amplificateur AV
Un signal
analogique à 2
voies peut aussi
être raccordé.
(en vente dans
le commerce)
Aux prises
d’entrée audio
Câble audio
Raccordement du dispositif USB
Attention
• Veillez à éteindre le lecteur avant de brancher ou de débrancher un dispositif USB.
• Si un disque dur externe est utilisé comme dispositif de stockage externe, veillez à allumer le disque dur avant d’allumer le lecteur.
• Si le dispositif USB est protégée, veillez à désactiver la protection.
• Pour raccorder le câble USB, tenez la fiche en l’orientant dans le bon sens et insérez-la tout droit dans le port.
• Une pression excessive sur la fiche peut causer un mauvais contact et empêcher les données de s’inscrire sur le dispositif USB.
• Lorsqu’un dispositif USB est raccordé et le lecteur allumé, ne débranchez pas le cordon d’alimentation.
Face avant du lecteur
02
Raccordement d’un appareil au port USB
À propos des dispositifs USB
Les dispositifs USB suivants peuvent être raccordés au lecteur.
• Mémoires flash USB compatibles USB 2.0 (capacité de 1 Go ou plus, 2 Go ou plus recommandés) ou disque dur (capacité 2 To ou plus)
• Format de fichier : FAT16, FAT32 ou NTFS
Remarque
• Les dispositifs formatés pour un autre système de fichiers ne pourront pas être utilisés.
• Les dispositifs USB contenant plusieurs partitions risquent de ne pas être reconnus.
• Certains dispositifs USB ne fonctionneront pas avec ce lecteur.
• Le fonctionnement des dispositifs USB n’est pas garanti.
Mémoire flash
(en vente dans
Panneau arrière
Mémoire flash
Remarque
• Le dispositif risque de ne pas fonctionner s’il est raccordé au port USB via un lecteur de carte mémoire ou un concentrateur USB.
• Utilisez un câble USB de 2 mètres au maximum.
Câble USB
le commerce)
Câble USB
(en vente dans
le commerce)
Disque dur, etc.
Disque dur, etc.
17
Fr
Raccordement au
02
réseau par l’interface LAN
En connectant ce lecteur au réseau par la prise LAN ou par un réseau LAN sans fil, vous pouvez lire les fichiers image, audio et vidéo enregistrés sur les composants en réseau, y compris votre ordinateur, via les entrées de HOME MEDIA GALLERY.
Mettez le serveur DHCP de votre routeur en service. Si votre routeur ne présente pas cette fonction, vous devrez paramétrer le réseau manuellement. Pour le détail, reportez-vous à
• Reportez-vous au mode d’emploi de l’appareil utilisé, car les appareils raccordés et les méthodes de raccordement peuvent être différents selon l’environnement Internet.
• Pour utiliser une connexion Internet à haut débit, il faut être abonné à un fournisseur de service Internet. Pour le détail, contactez votre fournisseur de service Internet le plus proche.
• Veuillez noter que Pioneer décline toute responsabilité quant aux erreurs de communication ou problèmes liés à la connexion au réseau de l’utilisateur ou aux dispositifs connectés. Contactez votre fournisseur ou le fabricant des dispositifs connectés.
Raccordement avec un câble LAN (réseau LAN filaire)
Raccordez la prise LAN de ce récepteur à la prise LAN de votre routeur (avec ou sans fonction de serveur DHCP) avec un câble LAN direct (CAT 5 ou supérieur).
Réglage de l’adresse IP
Remarque
Panneau arrière
à la page 39.
Spécifications de la prise LAN
Prise LAN : Prise Ethernet (10BASE-T/100BASE-TX)
Connexion à un réseau LAN sans fil
Des réglages manuels doivent être effectués pour pouvoir se connecter à un réseau LAN sans fil. Pour le détail, reportez-vous à
Ordinateur
Connexion sans fil au réseau
Internet
WAN
à la page 42.
Modem
Routeur
Raccordement du cordon d’alimentation
Lorsque tous les appareils ont été raccordés, vous pouvez brancher le cordon d’alimentation.
Panneau arrière
18
Fr
(en vente dans
le commerce)
Ordinateur
ModemCâble LAN
LAN
321
(en vente dans le commerce)
WAN
Câble LAN
Routeur
Internet
À la prise murale
Cordon
d’alimentation
(inclus)
Chapitre 3
Pour commencer
03
Paramétrage à l’aide du menu Setup Navigator
Veillez à bien régler ces paramètres lorsque vous utilisez le lecteur dans les situations suivantes.
• La première fois que vous utilisez le lecteur.
• Après le formatage avec Configuration initiale.
Attention
• Assurez-vous que le lecteur et les autres appareils sont reliés correctement avant de les mettre en service. Allumez aussi les appareils raccordés au lecteur avant d’allumer le lecteur.
• Si vous utilisez un téléviseur ou un vidéoprojecteur Pioneer compatible avec la fonction de contrôle, activez le contrôle sur l’appareil raccordé avant d’allumer le lecteur.
1 Allumez le téléviseur et sélectionnez l’entrée.
Reportez-vous au mode d’emploi du téléviseur pour le détail sur son fonctionnement.
2 Allumez le lecteur.
Appuyez sur STANDBY/ON. Assurez-vous que le menu Guide de Configuration
s’affiche.
Si le menu Setup Navigator ne s’affiche pas
Appuyez sur HOME MENU pour afficher la page Home Menu, sélectionnez Configuration initiale Guide de Configuration Démarrer, puis appuyez sur ENTER.
3 Lancez le Guide de Configuration.
Appuyez sur ENTER.
•Le Guide de Configuration s’ouvre.
4 Sélectionnez la langue des menus.
Utilisez / pour effectuer un choix, puis appuyez sur ENTER.
Lorsqu’un téléviseur Pioneer compatible avec la fonction de contrôle est raccordé à la prise HDMI OUT de ce lecteur, les réglages de langue du t élév iseu r Pioneer sont importés avant que le Guide de Configuration ne s’ouvre.
5 Sélectionnez la résolution appropriée pour le téléviseur raccordé.
Utilisez / pour effectuer un choix, puis appuyez sur
ENTER.
6 Sélectionnez le format approprié pour le téléviseur raccordé.
Utilisez / pour effectuer un choix, puis appuyez sur
ENTER.
7 Fermez le menu Guide de Configuration.
Appuyez sur ENTER.
Guide de Configuration se ferme et les réglages sont sauvegardés.
•Appuyez sur RETURN pour revenir à l’écran précédent.
19
Fr
Chapitre 4
04
Playback
Lecture de disques ou de fichiers
Le fonctionnement de base du lecteur est décrit dans cette section.
Pour les types de disques et de fichiers pouvant être lus, reportez-vous à page 6. Les fichiers vidéo, photo et audio enregistrés sur des disques sont lus avec Home Media Gallery (page 28).
1 Appuyez sur STANDBY/ON pour allumer le lecteur.
Allumez le téléviseur et sélectionnez tout d’abord l’entrée.
2 Appuyez sur OPEN/CLOSE pour ouvrir le tiroir à disque et insérez le disque.
Remarque
• Insérez le disque en orientant sa face imprimée vers le haut.
• Il faut plusieurs douzaines de secondes au lecteur pour lire les informations du disque. Lorsque les informations ont été lues, le type du disque est indiqué sur l’afficheur de la face avant du lecteur.
• Si des restrictions d’emploi ont été posées par un enregistreur BD sur le BD inséré, l’écran de saisie du code PIN apparaît. Dans ce cas, saisissez votre code PIN.
3 Appuyez sur pour lire le disque.
• Pour mettre en pause, appuyez sur pendant la lecture.
• Pour arrêter la lecture, appuyez sur STOP.
Remarque
• La lecture commence automatiquement pour certains disques lorsque le tiroir à disque est fermé.
• Certains disques BD-ROM/DVD-Vidéo disposent d’un contrôle parental. Saisissez le mot de passe enregistré dans les paramètres du lecteur pour annuler le contrôle parental. Pour le détail, reportez­vous à page 41.
• Certains disques BD-R/-RE ont une protection interdisant la lecture. Pour annuler la protection, précisez le mot de passe spécifié pour le disque.
• Si l’image et le son ne sont pas correctement transmis,
Si le menu du disque s’affiche
Pour certains disques, le menu du disque s’affiche automatiquement au début de la lecture. Le contenu du menu du disque et le fonctionnement du menu dépendent du disque.
20
Fr
En cas de panne
à la page 48.
Reprise de la lecture au point où elle a été arrêtée (fonction de reprise de la lecture)
• Si vous appuyez sur STOP pendant la lecture, le point où le disque a été arrêté est enregistré dans la mémoire. Ensuite, lorsque vous appuyez sur , la lecture se poursuit à partir de ce point.
• Pour annuler la reprise de la lecture, appuyez sur STOP pendant l’arrêt de la lecture.
Remarque
• La reprise de la lecture est automatiquement annulée dans les cas suivants :
– Lorsque le tiroir à disque est ouvert. – Lorsque vous changez de liste de fichiers. – Lorsque vous mettez le lecteur hors service. (La
reprise de la lecture n’est pas annulée dans le cas des BD et des DVD.)
– Quand il est entré dans l’écran du mode Miracast/
Wi-Fi Direct. (page 31)
• Si vous voulez continuer la lecture à une position spécifiée au préalable, reportez-vous à
plage particulière de disques, de titres ou d’un chapitre (plage/fichier) dans un ordre aléatoire
page 27.
• La reprise de la lecture ne peut pas être utilisée pour certains disques.
Lecture d’une
à la
Vue rapide (Vue rapide avec audio)
Le son est restitué pendant que les images vidéo sont lues à environ 1,5 fois la vitesse normale.
Appuyez sur pendant la lecture des images vidéo du BD ou du DVD.
• Un appui sur pendant la vue rapide fait passer en avance rapide.
Pour revenir à la lecture normale
•Appuyez sur .
Remarque
• Vous ne pouvez pas mettre en pause pendant la vue rapide. Veuillez faire une pause après le retour à la lecture normale.
• Quant à la tonalité lors de la vue rapide, la sortie vient de PCM quelle que soit la configuration du corps principal de l’appareil.
• Il n’est pas possible de commuter le son pendant la vue rapide.
• En fo nct io n du fo rma t a ud io, co mme Do lby Tr ueH D e t DTS- HD Master Audio, il peut n’y avoir aucune sortie de son pendant l'avance rapide.
• Pour les conditions de sortie de chaque voix, veuillez vous référer à la section
numériques restitués
À propos des formats audio
à la page 44.
Recherche avant et arrière
Pendant la lecture ou la vue rapide, appuyez sur
REV ou FWD.
• La vitesse de la recherche change chaque fois que vous appuyez sur la touche. La variation de vitesse dépend du disque ou du fichier (la vitesse est indiquée sur l’écran du téléviseur).
Pour revenir à la lecture normale
Appuyez sur .
Lecture de chapitres, de plages ou de fichiers particuliers
Lecture au ralenti
Pendant la pause de la lecture, appuyez un instant sur /.
• La vitesse change chaque fois que vous appuyez sur la touche (la vitesse est indiquée sur l’écran du téléviseur).
• La lecture arrière au ralenti n’est pas disponible.
Pour revenir à la lecture normale
•Appuyez sur .
Lecture avant et arrière pas à pas
04
Pendant la lecture, précisez le numéro du chapitre, de la plage ou du fichier que vous voulez lire.
• Utilisez les touches numériques (0 à 9) pour préciser le numéro, puis appuyez sur ENTER.
•Appuyez sur CLEAR pour effacer les valeurs saisies.
Saut de contenu
Pendant la lecture, appuyez sur ou .
• Si vous appuyez sur , la lecture saute au début du chapitre, de la plage ou du fichier suivant.
• Si vous appuyez sur pendant la lecture d’un fichier vidéo ou audio, la lecture revient au début du chapitre, de la plage ou du fichier en cours de lecture. Appuyez deux fois sur la touche pour localiser le début du chapitre, de la plage ou du fichier précédent.
• Si vous appuyez sur pendant la lecture d’un fichier photo, la lecture revient au fichier précédent.
Pour revenir à une position peu de temps auparavant
Appuyez pendant la lecture pour revenir à une position 10 secondes avant.
Pendant la lecture, appuyez sur REPLAY.
Pour avancer à une position légèrement en avant
Appuyez pendant la lecture pour avancer à une position 30 secondes après.
Pendant la lecture, appuyez sur SHORT SKIP.
Pendant la pause de la lecture, appuyez un
instant sur /.
• Chaque fois que vous appuyez sur la touche, la lecture avance d’une image à la fois.
• La lecture arrière n’est pas possible.
Pour revenir à la lecture normale
•Appuyez sur .
Lecture répétée d’un passage précis d’un titre ou d’une plage (Répétition A-B)
Procédez de la façon suivante pour répéter un passage précis d’un titre ou d’une plage.
1 Pendant la lecture, appuyez sur A-B pour sélectionner le début du passage.
[A-] apparaît sur l’écran du téléviseur.
2 Pendant la lecture, appuyez sur A-B pour sélectionner la fin du passage.
• La lecture du passage A-B commence.
Pour annuler la lecture du passage A-B
•Appuyez sur A-B pendant la lecture répétée du passage A-B.
Remarque
• La lecture répétée du passage A-B est annulée dans les cas suivants :
– Si vous effectuez une recherche hors de la plage
spécifiée pour la répétition.
– Si vous démarrez une autre lecture répétée ou
lecture aléatoire.
21
Fr
Répétition de la lecture
04
(Lecture répétée)
Procédez de la façon suivante pour répéter le disque, le titre, le chapitre, la plage ou le fichier actuel.
Pendant la lecture, appuyez sur REPEAT.
•À chaque pression sur REPEAT le mode de répétition change de la façon suivante.
BD
Chapitre actuel Titre actuel
DVD
Chapitre actuel Titre actuel Tous les titres
CD/Fichier vidéo/Fichier audio/Fichier photo
Plage/fichier actuel Toutes les plages/Tous les fichiers du dossier
Pour annuler la lecture répétée
• Appuyez plusieurs fois sur REPEAT pendant la lecture répétée.
Remarque
• La lecture répétée est annulée dans les cas suivants : – Si vous effectuez une recherche hors de la plage
spécifiée pour la répétition.
– Si vous démarrez une autre lecture répétée ou
lecture aléatoire.
Lecture dans l’ordre souhaité (Lecture programmée)
1 Pendant la lecture, appuyez sur PROGRAM.
• L’écran de programmation s’affiche.
2 Sélectionnez le numéro de programmation.
Utilisez / pour effectuer un choix, puis appuyez sur
ENTER.
3 Sélectionnez le morceau/titre/chapitre que vous souhaitez lire.
Utilisez /// pour effectuer un choix, puis appuyez sur ENTER.
4 Appuyez sur .
• La lecture commence.
Modification de la programmation
1 Sélectionnez le numéro de la programmation que vous voulez modifier, puis appuyez sur ENTER.
2 Sélectionnez le titre/chapitre, puis appuyez sur ENTER.
Suppression d’une programmation
Sélectionnez le numéro de la programmation que
vous voulez supprimer, puis appuyez sur CLEAR.
• Pour supprimer toutes les programmations, appuyez sur RETURN.
22
Fr
Remarque
• Si vous utilisez des CD audio pour la lecture programmée, indiquez le numéro de plage au point 3.
• Cette fonction n’agit pas avec les BD.
Pose de signets
Vous pouvez poser des signets sur la vidéo en cours de lecture pour revenir plus tard à la scène marquée.
Pendant la lecture, appuyez sur BOOKMARK.
•Un signet est posé.
• Le nombre de signets pouvant être posés est limité à
12.
Lecture d’une scène marquée
1 Appuyez sur la touche BOOKMARK et maintenez­la quelques secondes enfoncée.
• La liste de signets apparaît.
2 Sélectionnez le signet que vous souhaitez lire.
Utilisez / pour effectuer un choix, puis appuyez sur ENTER.
Suppression d’un signet
Sélectionnez le signet que vous voulez
supprimer, puis appuyez sur CLEAR.
• Pour certains disques il ne sera pas possible de poser de signets.
• Les signets sont annulés dans les cas suivants : – Lorsque le lecteur est éteint. – Lorsque le tiroir à disque est ouvert.
Zoom
Pendant la lecture, appuyez sur ZOOM.
• À chaque pression sur ZOOM, le niveau de zoom change de la façon suivante.
[Zoom 2x] [Zoom 3x] [Zoom 4x] [Zoom 1/2] [Zoom 1/3] [Zoom 1/4] Normal (pas d’indication)
Remarque
• Cette fonction n’agit pas avec certains disques.
Lecture de photos en diaporama
Cette fonction permet un changement automatique des photos.
Pendant la lecture, appuyez sur INDEX.
• Affichez les miniatures des fichiers d’images. Le nombre de miniatures pouvant être affichées à la fois se limite à 12.
• Si vous sélectionnez une miniature et appuyez sur ENTER, le diaporama démarrera par l’image sélectionnée.
Rotation/renversement de photos
Pendant un diaporama ou la pause du diaporama, l’image change d’orientation de la façon suivante lorsque vous appuyez sur les touches ///.
Touche : Rotation de 90° dans le sens horaire Touche : Rotation de 90° dans le sens antihoraire Touche : Renversement horizontal Touche : Renversement vertical
Changement de l’angle de prise de vues
Pour les disques BD-ROM et DVD-Vidéo enregistrés sous différents angles de prise de vues, les angles peuvent être changés au cours de la lecture.
1 Pendant la lecture, appuyez sur FUNCTION.
2 Sélectionner Angle dans le menu FUNCTION.
• L’angle actuel et le nombre total d’angles enregistrés sont indiqués à l’écran du téléviseur.
• Si les angles ne sont pas changés, changez-les depuis l’écran de menu du disque.
Remarque
• Certains disques ne peuvent pas changer les angles.
Changement des sous-titres
Pour les disques ou les fichiers sur lesquels différents sous-titres ont été enregistrés, les sous-titres peuvent être changés au cours de la lecture.
Attention
• Les sous-titres ne peuvent pas être changés dans le cas de disques enregistrés par un enregistreur DVD ou BD. Reportez-vous aussi au mode d’emploi de l’appareil utilisé pour l’enregistrement.
Pendant la lecture, appuyez sur SUBTITLE.
• Les sous-titres actuels et le nombre total de sous­titres enregistrés sont indiqués à l’écran du téléviseur. Pour changer de sous-titres, appuyez une nouvelle fois sur SUBTITLE.
• Les sous-titres peuvent aussi être changés en sélectionnant Sous-titres sur le menu FUNCTION.
• Si les sous-titres ne changent pas lorsque vous appuyez sur SUBTITLE, changez-les par le menu du disque.
Masquage des sous-titres
Appuyez plusieurs fois sur SUBTITLE ou
sélectionnez Sous-titres dans le menu FUNCTION pour régler ce paramètre sur Off.
À propos de l’affichage de sous­titres externes pendant la lecture des fichiers DivX
Outre les sous-titres enregistrés sur les fichiers DivX, ce lecteur peut aussi afficher des sous-titres externes. Si un fichier a le même nom qu’un fichier DivX à part l’extension, et si l’extension est une des extensions suivantes, le fichier sera traité comme fichier de sous­titres externes. Notez bien que les fichiers DivX et les fichiers de sous-titres externes doivent se trouver dans le même dossier. Un seul fichier de sous-titres externes peut être utilisé sur ce lecteur. Utilisez un ordinateur, etc. pour supprimer les fichiers des sous-titres externes dont vous n’avez pas besoin pour un disque. Les fichiers texte ayant les extensions “.smi”, “.srt”, “.sub” et “.txt” ne sont pas pris en charge.
Remarque
• Avec certains fichiers, les sous-titres externes ne pourront pas être affichés correctement.
Sous-titres mobiles
La position des sous-titres apparaissant pendant la lecture de BD-ROM ou DVD peut être changée.
1 Lisez le BD-ROM ou le DVD-Vidéo et affichez les sous-titres sur l’écran du téléviseur.
2 Appuyez au moins 2 secondes sur la touche SUBTITLE.
• Le Mode de décalage du titre est spécifié.
• [Mode de décalage du titre] apparaît sur l’écran du téléviseur.
3 Utilisez les touches / pour changer la position des sous-titres.
• Utilisez les touches / pour changer la position des sous-titres.
• Une fois que le paramétrage est terminé, appuyez sur
ENTER.
4 Annulez le Mode de décalage du titre. Appuyez sur la touche ENTER.
04
23
Fr
Changement du son
04
Pour les disques ou les fichiers sur lesquels différents flux/voies audio ont été enregistrés, les flux/voies audio peuvent être commutés au cours de la lecture.
Pendant la lecture, appuyez sur AUDIO.
• Le son actuel et le nombre total de flux audio enregistrés sont indiqués à l’écran du téléviseur. Pour changer de son, appuyez une nouvelle fois sur AUDIO.
• Le son peut aussi être changé en sélectionnant Audio sur le menu FUNCTION.
•Si AUDIO ne permet pas de changer le son, changez- le par le menu du disque.
Commutation de la zone de lecture CD/SACD
1 Sélectionnez la zone que vous souhaitez lire.
En mode d’arrêt, appuyez sur CD/SACD. La zone de lecture change sur l’afficheur de la face avant à chaque pression sur la touche.
[CD AREA] [SACD 2CH] [SACD MCH]  (retour au début)
• Pendant la lecture, appuyez deux fois sur STOP pour annuler la lecture continue avant de sélectionner la zone de lecture.
Affichage des informations du disque
Appuyez sur DISPLAY.
Les informations du disque apparaissent sur l’écran du téléviseur. Pour masquer les informations, appuyez une nouvelle fois sur DISPLAY.
Les informations affichées sont différentes pendant la lecture et pendant la pause de la lecture.
Utilisation de BONUSVIEW ou de BD-LIVE
Ce lecteur est compatible avec les BD-Vidéo BONUSVIEW et BD-LIVE.
Lorsque vous utilisez des BD-Vidéo compatibles avec BONUSVIEW, vous bénéficiez de certaines fonctions comme l’image secondaire (image dans l’image) (page 26) et le son secondaire (page 26). Avec les BD­Vidéo offrant BD-LIVE, des images vidéo spéciales ainsi que d’autres données peuvent être téléchargées d’Internet.
Les données enregistrées sur un BD-Vidéo et téléchargées de BD-LIVE se stockent sur une mémoire flash USB (mémoire externe). Pour bénéficier de ces fonctions, raccordez une mémoire flash USB (capacité minimale 1 Go, 2 Go ou plus sont recommandés) de type USB 2.0 High Speed (480 Mbits/s) au port USB.
• Veillez à éteindre le lecteur avant d’insérer ou de retirer la mémoire flash USB.
• Pour rappeler les données sauvegardées sur la mémoire flash USB, insérez d’abord la mémoire utilisée lors du téléchargement des données (si une autre mémoire est insérée, les données enregistrées sur la mémoire flash USB ne seront pas lues).
• Si la mémoire flash USB utilisée contient d’autres données (enregistrées antérieurement), l’image et le son ne seront pas lus correctement.
• Ne retirez pas la mémoire flash USB pendant la lecture.
• Le chargement des données (lecture/écriture) nécessite un certain temps.
Attention
• Si l’espace disponible sur la mémoire flash USB n’est pas suffisant, il peut être impossible d’utiliser les fonctions BONUSVIEW et BD-LIVE. Dans ce cas, reportez-vous à
BD et des données des applications
effacer les données du Paquet Virtuel et les données BD-LIVE sur la mémoire flash USB.
Effacement des données ajoutées aux
à la page 40 pour
24
Fr
Remarque
• Le fonctionnement des mémoires flash USB n’est pas garanti.
• La lecture des données de la fonction BD-LIVE varie selon la mémoire utilisée. Pour le détail, consultez la notice fournie avec la mémoire.
• Pour bénéficier de la fonction BD-LIVE, une connexion réseau et des réglages sont nécessaires (pages 18 et 39).
• BD-LIVE est une fonction assurant une connexion à Internet. Les disques disposant de la fonction BD-LIVE peuvent envoyer les codes d’identification de ce lecteur et du disque au fournisseur de contenus par Internet.
Fonctions de lecture
Les fonctions pouvant être utilisées dépendent du type de disque et de fichier. Dans certains cas, certaines fonctions ne peuvent pas être utilisées. Les fonctions disponibles sont indiquées dans le tableau suivant.
Type de disque/fichier
1
Fonction
2
Vue rapide Recherche avant et
arrière
BD-ROM
BD-R
/-RE
  
3
3
Short Skip/Replay   Lecture de titres, de
chapitres ou de plages particuliers
  
Saut de contenu  
Lecture au ralenti Lecture avant et arrière
pas à pas
5, 6
7, 8
Lecture répétée A-B
  
  
7
 
Lecture répétée  Zoom  
9
Angle
Sous-titres
11
Son
10

  
  
Informations du disque  
1. Certaines fonctions peuvent ne pas être disponibles pour certains disques ou fichiers, même si [] est indiqué dans le tableau.
2. Selon le format audio, tel que Dolby TrueHD et DTS-HD Master Audio, il peut n’y avoir aucune sortie de son pendant l’avance rapide.
3. Pendant la recherche avant et arrière, le son n’est pas audible.
4. Pendant la recherche avant et arrière, le son est audible.
5. Pendant la lecture au ralenti le son n’est pas audible.
6. La lecture arrière au ralenti n’est pas disponible.
7. Si un chapitre est commuté, certains disques provoquent un retour automatique à la lecture normale.
8. La lecture arrière pas à pas n’est pas disponible.
9. La marque d’angle apparaît pour les scènes enregistrées sous divers angles si Indicateur Angle est réglé sur Activé (page 38).
10. • Les types de sous-titres enregistrés dépendent du disque et du fichier.
• Dans certains cas, les sous-titres peuvent changer ou l’écran de commutation du disque peut s’afficher immédiatement, sans que les sous­titres actuels ni le nombre total de sous-titres enregistrés sur le disque ne soient indiqués.
11. Les types de sons secondaires enregistrés dépendent du disque et du fichier.
DVD-
Vidéo
3
DVD-R/-
RW
(Format
VR)
3
AVCREC AVCHD
3
3
Fichier
vidéo
3
Fichier
photo
Fichier
audio
4
CD
audio
4
04
25
Fr
Utilisation du menu
04
FUNCTION
Les fonctions pouvant être rappelées dépendent du mode de fonctionnement du lecteur.
1 Affichez le menu FUNCTION. Appuyez sur FUNCTION pendant la lecture.
2 Sélectionnez et réglez le paramètre.
Utilisez / pour effectuer un choix, puis appuyez sur ENTER.
Remarque
• Les paramètres ne pouvant pas être changés apparaissent en gris. Les paramètres pouvant être sélectionnés dépendent de l’état du lecteur.
Pour changer le réglage du paramètre sélectionné
Utilisez / pour le changer.
Pour fermer le menu FUNCTION
Appuyez sur FUNCTION.
Liste des paramètres du menu FUNCTION
Paramètre Description
Titre (plage)
Chapitre Affichage des informations concernant
Fichier Affichez les informations du fichier
Heure Affichage du temps écoulé ou restant.
Mode Changement du mode de lecture
Audio Changement du son. Angle Changement de l’angle de prise de vue
Sous-titres Changement de la langue des sous-
Page Code Changement de page des codes de sous-
Vidéo secondaire
Audio secondaire
Bitrate Affichage du débit binaire du son/de
Statisme off Arrêt de l’image fixe d’un BD-ROM. Short Skip Avancer à une position 30 secondes
Replay Revenir à une position 10 secondes
Diaporama Changement de vitesse du diaporama
Transition Changement de style du diaporama
1. Une de ces informations apparaît selon le type de disque.
2. La marque d’image secondaire apparaît pour les scènes
3. La marque de son secondaire apparaît pour les scènes
1
Affichage des informations concernant le titre du disque en cours de lecture et du nombre total de titres sur le disque. Également sélection du titre devant être lu. (Voir la description suivante.)
le chapitre en cours de lecture (plage/ titre) et du nombre total de chapitres sur le disque. Également sélection du chapitre (plage/titre) devant être lu. (Voir la description suivante.)
actuel. Sélectionnez votre fichier favori.
Également spécification du temps où la lecture doit commencer. (Voir la description suivante.)
(page 27).
d’un BD-ROM/DVD-Vidéo.
titres.
titres.
2
Sélection de l’image secondaire d’un BD-ROM (Image dans l’image).
3
Sélection du son secondaire d’un BD-ROM.
l’image/de l’image/du son secondaire.
après.
avant.
pendant un diaporama.
pendant un diaporama.
enregistrées avec une image secondaire si Indictateur PIP est réglé sur Activé (page 38).
enregistrées avec un son secondaire si Indicateur second audio est réglé sur Activé (page 38).
26
Fr
Remarque
• Les paramètres pouvant être sélectionnés dépendent du type de disque.
• Les types de flux audio secondaires enregistrés dépendent du disque et du fichier.
• Certains disques n’ont pas de son secondaire ou d’image secondaire.
• Dans certains cas, le son secondaire ou l’image secondaire peut changer ou l’écran de commutation peut s’afficher immédiatement, sans que le son secondaire ou l’image secondaire ou le nombre total de sons secondaires ou d’images secondaires enregistrés sur le disque ne soit indiqué.
Lecture à partir d’un temps précis (Recherche temporelle)
1 Sélectionnez Heure.
Utilisez / pour effectuer un choix, puis appuyez sur
ENTER. 2 Précisez le temps.
Utilisez les touches numériques (0 à 9) pour préciser le temps.
• Pour lire à partir de 45 minutes, précisez 0, 0, 4, 5, 0 et 0, puis appuyez sur ENTER.
• Pour lire à partir de 1 heure 20 minutes, précisez 0, 1, 2, 0, 0 et 0, puis appuyez sur ENTER.
•Appuyez sur CLEAR pour effacer les valeurs saisies.
3 Démarrez la lecture au temps précisé. Appuyez sur ENTER.
Lecture d’un titre, d’un chapitre, d’une plage ou d’un fichier particulier (Recherche)
1 Sélectionnez Titre ou Chapitre (plage/fichier).
Utilisez / pour effectuer un choix, puis appuyez sur
ENTER.
2 Précisez le numéro du titre ou du chapitre (plage/ fichier).
Utilisez les touches numériques (0 à 9) ou / pour préciser le numéro.
• Pour rechercher par exemple le titre 32, précisez 3 et 2, puis appuyez sur ENTER.
•Appuyez sur CLEAR pour effacer les valeurs saisies.
3 Démarrez la lecture à partir du titre, du chapitre ou de la plage précisé. Appuyez sur ENTER.
Lecture d’une plage particulière de disques, de titres ou d’un chapitre (plage/ fichier) dans un ordre aléatoire
Vous avez le choix entre 2 types de lecture aléatoire.
1 Sélectionnez Mode.
Utilisez / pour effectuer un choix, puis appuyez sur
ENTER.
2 Sélectionnez le mode de lecture.
Utilisez / pour effectuer un choix, puis appuyez sur ENTER.
Random play
La plage de disques, de titres ou le chapitre (morceau/ fichier) spécifié est lu dans un ordre aléatoire. Le même élément peut être lu de manière consécutive.
Shuffle play
La plage de disques, de titres ou le chapitre (morceau/ fichier) spécifié est lu dans un ordre aléatoire. Chaque élément n’est lu qu’une seule fois.
Continuation de la lecture à partir de la position spécifiée (Poursuite du visionnage)
Cette fonction permet de poursuivre la lecture à une position spécifiée au préalable, même après l’extinction du lecteur.
Réglage
Pendant la lecture, appuyez sur CONTINUED à la
position où vous voulez poursuivre le visionnage.
Le temps écoulé jusqu’à la position spécifiée est indiqué à l’écran du téléviseur.
Lecture
1 Appuyez sur pour lire le titre pour lequel vous avez spécifié une position.
L’écran de confirmation de la poursuite de la lecture apparaît.
• Dans les cas suivants, l’écran de confirmation de poursuite du visionnage s’affiche.
Pour le BD vidéos
L’écran s’affiche après la lecture de la fonction principale.
Pour les disques enregistrés
L’écran s’affiche après la sélection du dossier et la lecture du titre pour lequel la poursuite de la lecture a été spécifiée.
2 Utilisez / pour sélectionner Yes, puis appuyez sur ENTER.
Démarrez la lecture au temps précisé.
Remarque
• Le temps spécifié pour la poursuite de la lecture est annulé lorsque OPEN/CLOSE est pressé.
• La poursuite de la lecture à un temps spécifié peut ne pas fonctionner correctement avec certains disques.
04
27
Fr
Chapitre 5
05
Lecture avec Home Media Gallery
Les fichiers enregistrés sur un ordinateur ou un DMS (Serveur multimédia numérique), comme mentionné ci-dessus, peuvent être lus par un contrôleur multimédia numérique externe (DMC). Les dispositifs contrôlés par ce DMC pour la lecture de fichiers sont appelés DMR (Digital Media Renderers). Ce lecteur prend en charge la fonction DMR. Lorsqu’il est en mode DMR, la lecture et l’arrêt de fichiers, entre autre, peuvent être activés depuis le contrôleur externe.
• Pour lire les fichiers audio enregistrés sur des appareils en réseau, la fonction de serveur DHCP de
À propos de Home Media Gallery
votre routeur doit être mise en service. Si votre routeur ne présente pas cette fonction, vous devrez paramétrer le réseau manuellement. Sinon, les fichiers enregistrés sur les appareils en réseau ne pourront pas être lus. Voir “Réglage de l’adresse IP” page 39.
La fonction Home Media Gallery de ce lecteur permet d’afficher une liste des sources d’entrée et de démarrer la lecture. Ce chapitre décrit comment configurer le lecteur et comment effectuer la lecture pour bénéficier de ces fonctions. Si vous lisez des fichiers enregistrés sur votre ordinateur ou un autre appareil connecté au réseau, nous vous conseillons de vous reporter aussi au mode d’emploi fourni avec cet appareil.
Les sources d’entrée peuvent être lues avec Home Media Gallery de la façon suivante.
• Disques BD-R/RE (format BDAV)
• Disques DVD-R/-RW (format VR)
• CD audio (CD-DA, SACD et DTS-CD)
• DVD/CD sur lesquels des fichiers vidéo, photo ou audio, etc. sont enregistrés.
• Dispositif USB
• Fichiers sur les serveurs (sur des ordinateurs ou appareils connectés au lecteur par une interface LAN.)
Remarque
• La fonction Home Media Gallery permet de lire des fichiers disponibles sur les serveurs multimédia connectés au même réseau local (LAN) que le lecteur.
• Les fichiers suivants peuvent être lus avec Home Media Gallery :
– Les ordinateurs fonctionnant sous Microsoft
Windows Vista ou XP avec Windows Media Player 11 installé
– Ordinateurs fonctionnant sous Microsoft Windows
7 avec Windows Media Player 12 installé
– Les serveurs multimédia numériques compatibles
avec la norme DLNA (sur les ordinateurs ou d’autres appareils)
Les fichiers enregistrés sur un ordinateur ou un DMS (Serveur multimédia numérique), comme mentionné ci­dessus, peuvent être lus par le lecteur multimédia
28
numérique (DMP). Le lecteur permet d’utiliser un DMP.
Fr
À propos de la lecture en réseau
Cet appareil utilise les technologies suivantes pour la lecture en réseau :
Windows Media Player
Reportez-vous à Windows Media Player 11/Windows Media Player 12 ci-dessus pour plus d’informations à ce sujet.
DLNA
Lecteur audio DLNA CERTIFIED La DLNA (Digital Living Network Alliance) est une alliance
transindustrielle des sociétés de production d’appareils électroniques grand public, d’ordinateurs et de périphériques mobiles. Digital Living permet aux consommateurs de partager aisément les médias numériques par leurs réseaux avec ou sans fil.
Le logo DLNA permet de trouver facilement les produits conformes aux Directives d’interopérabilité DLNA. Cet appareil est conforme aux Directives d’interopérabilité DLNA v1.5. Lorsqu’un ordinateur intégrant un logiciel serveur DLNA ou un autre périphérique compatible DLNA est relié à ce lecteur, certains paramètres du logiciel ou du périphérique devront éventuellement être changés. Veuillez vous reporter au mode d’emploi du logiciel ou du périphérique pour plus d’informations à ce sujet.
®
, le logo DLNA et DLNA CERTIFIED® sont des
DLNA marques commerciales, des marques de service ou des marques de certification de la Digital Living Network Alliance.
®
Contenus lisibles via un réseau
• Certains fichiers ne pourront pas être lus correctement bien qu’ils soient dans un format compatible.
• Selon le type de serveur ou la version utilisé, certaines fonctions ne seront pas prises en charge.
• Les formats de fichiers pris en charge varient d’un serveur à l’autre. C’est pourquoi, les fichiers qui ne sont pas pris en charge par votre serveur n’apparaissent pas sur cet appareil. Pour plus d’informations, contactez le constructeur de votre serveur.
Avis de non responsabilité concernant les contenus diffusés par un tiers
L’accès aux contenus fournis par des tiers exige une connexion Internet haut débit et peut aussi exiger la création d’un compte et des droits de souscription.
Les services de contenus de tiers peuvent être changés, suspendus ou interrompus à tout moment sans préavis, et Pioneer décline toute responsabilité quant à ces changements.
Pioneer ne certifie ou garantit pas que les services de contenus continueront d’être fournis ou seront disponibles pendant une période précise et décline toute garantie explicite ou implicite de ce type.
Anomalies lors de lecture en réseau
• La lecture peut se bloquer si vous éteignez l’ordinateur ou supprimez des fichiers multimédia de l’ordinateur pendant la lecture de contenu.
• En cas de problèmes de réseau (trafic intense, etc.) le contenu risque de ne pas s’afficher ou de ne pas être lu correctement (la lecture peut être interrompue ou bloquée). Pour éviter ce type de problème, il est conseillé de relier le lecteur et l’ordinateur par un câble 10BASE-T/100BASE-TX.
• Si plusieurs clients lisent les mêmes fichiers simultanément, la lecture peut être interrompue ou se bloquer.
• Selon le logiciel antivirus installé sur l’ordinateur raccordé et le réglage de ce logiciel, la connexion réseau peut se bloquer.
Pioneer n’est pas responsable du mauvais fonctionnement du lecteur et/ou des fonctions Home Media Gallery dû à des erreurs ou dysfonctionnements de la communication avec votre connexion réseau et/ou votre ordinateur, ou un autre appareil raccordé. Veuillez contacter le fabricant de votre ordinateur ou votre fournisseur de service Internet.
Windows Media est une marque déposée ou une marque commerciale de Microsoft Corporation aux États-Unis et/ ou dans d’autres pays.
Ce produit intègre une technologie détenue par Microsoft Corporation, qui ne peut être utilisée et distribuée que sous licence de Microsoft Licensing, Inc.
®
Microsoft Windows Windows
, Windows®7, Windows®Vista, Windows®XP,
®
2000, Windows®Millennium Edition,
®
98 et WindowsNT® sont des marques déposées ou des marques commerciales de Microsoft Corporation aux états-Unis d’Amérique et/ou dans d’autres pays.
Lecture de fichiers sur le réseau
1 Appuyez sur Menu principal pour afficher l’écran Menu principal.
2 Sélectionnez [Home Media Gallery] et appuyez sur ENTER.
3 Sélectionnez le serveur contenant le fichier que vous voulez lire.
4 Sélectionnez le fichier que vous voulez lire.
Utilisez / pour effectuer un choix, puis appuyez sur ENTER.
Pour quitter la fonction Home Media Gallery
Appuyez HOME MENU principal.
Lecture de disque/USB
1 Appuyez sur Menu principal pour afficher l’écran Menu principal.
2 Sélectionnez [Home Media Gallery] et appuyez sur ENTER.
3 Sélectionnez Disc ou USB.
Utilisez / pour effectuer un choix, puis appuyez sur
ENTER.
4 Sélectionnez Photo/Music/Video/AVCHD.
Utilisez / pour effectuer un choix, puis appuyez sur ENTER.
• Ce point n’est pas pour les disques enregistrés dans le format BDAV/VR/AVCREC.
• Pour lire des fichiers dans le formant AVCHD sur un dispositif USB, créez un dossier intitulé “AVCHD” sur le dispositif USB, puis copiez le dossier “BDMV” contenant les fichiers à lire dans le dossier “AVCHD”.
5 Sélectionnez le titre/la plage ou le fichier que vous voulez lire.
Utilisez / pour effectuer un choix, puis appuyez sur ENTER.
Démarrez la lecture à partir du titre/de la plage ou fichier sélectionné.
• Si le fichier que vous voulez lire se trouve dans un dossier, sélectionnez d’abord le dossier contenant le fichier.
05
29
Fr
Lecture de fichiers photo
05
À propos du diaporama
Les photos du dossier s’affichent et changent automatiquement.
Remarque
• Certains disques BD-R/-RE ont une protection interdisant la lecture. Pour annuler la protection, précisez le mot de passe spécifié pour le disque.
• Il faudra peut-être attendre quelques secondes avant que la lecture démarre. C’est normal.
• Certains fichiers ne pourront pas être lus correctement.
• Le nombre de vues peut être limité.
• Selon les dispositifs raccordés et la situation, il faut attendre quelque temps avant que la lecture ne commence et l’image change.
• Pour ajouter d’autres plages ou fichiers, répétez les points 4 à 6.
Lecture de la Playlist
1 Appuyez sur Menu principal pour afficher l’écran Menu principal.
2 Sélectionnez [Home Media Gallery] et appuyez sur ENTER.
3 Sélectionnez la Playlist.
Utilisez / pour effectuer un choix, puis appuyez sur
ENTER.
4 Sélectionnez la plage ou le fichier devant être lu.
Utilisez / pour effectuer un choix, puis appuyez sur ENTER.
La lecture commence par la plage ou le fichier sélectionné et se poursuit jusqu’au dernier de la liste. Utilisez / pour lire la plage ou le fichier précédent ou suivant. L’écran Now Playing s’affiche.
Lecture dans l’ordre souhaité (Playlist)
Les disques permettant d’ajouter des plages et des fichiers à la Liste de Lecture sont les suivants.
• DVD/CD/Dispositifs USB sur lesquels des fichiers audio sont enregistrés
Ajout de plages ou de fichiers
Procédez de la façon suivante pour ajouter des plages et des fichiers, et créer la Liste de lecture.
1 Appuyez sur Menu principal pour afficher l’écran Menu principal.
2 Sélectionnez [Home Media Gallery] et appuyez sur ENTER.
3 Sélectionnez Disc ou USB.
Insérez d’abord le disque. Utilisez / pour effectuer un choix, puis appuyez sur
ENTER.
4 Sélectionnez la plage ou le fichier devant être ajouté.
Utilisez pour le valider.
5 Appuyez sur POP UP MENU pour afficher le menu POP UP MENU.
6 Sélectionnez Ajouter à la liste de lecture pour ajouter à la Playlist.
Utilisez / pour effectuer un choix, puis appuyez sur ENTER.
La plage ou le fichier sélectionné au point 4 est ajouté à la Liste de lecture.
30
Fr
Suppression de plages ou fichiers de la Playlist
1 Sélectionnez la plage ou le fichier devant être supprimé, puis appuyez sur POP UP MENU pour afficher le menu POP UP MENU.
2 Utilisez / pour sélectionner Delete from Playlist, puis appuyez sur ENTER.
Remarque
• Dans les cas suivants, toutes les informations dans la liste de lecture seront supprimées :
– Lorsque vous ouvrez le plateau de disque. – Lorsque vous éteignez l’alimentation.
Connexion par MiracastTM/ Direct
À propos de la Wi-Fi
Le logo Wi-Fi CERTIFIED est une marque déposée de la Wi-Fi Alliance.
La marque d’identification Wi-Fi Protected Setup est une marque de Wi-Fi Alliance.
Wi-Fi, Wi-Fi Protected Setup, Wi-Fi Direct, Miracast, WPA, WPA2 sont des marques de l’organisation Wi-Fi Alliance.
Utiliser les fonctions’ Miracast/Wi-Fi Direct de l’appareil
Miracast et Wi-Fi Direct sont des fonctions pour connecter vos appareils mobiles à l’appareil sans utiliser un routeur LAN sans fil.
Miracast est une fonction qui vous permet d’afficher les vidéos sur un appareil mobile comme sur une TV à grand écran.
Wi-Fi Direct est une fonction qui vous permet de lire des fichiers photo, musique et vidéo stockés sur un appareil mobile avec l’appareil en installant une application compatible DLNA sur votre appareil mobile.
Attention
• En fonction du modèle, une connexion n’est peut-être pas possible, même pour des modèles compatibles Miracast/Wi-Fi Direct.
• La procédure de connexion à Miracast/Wi-Fi Direct dépend de l’appareil mobile. Pour des informations détaillées, consultez le mode d’emploi de l’appareil mobile.
• En fonction des spécifications de l’appareil mobile ou du type et de la version du système d’exploitation, il n’est peut-être pas compatible avec la fonction Miracast/Wi-Fi Direct. Pour des informations détaillées, consultez le mode d’emploi de l’appareil mobile.
• Certains contenus protégés par les droits d’auteur, etc., peuvent, selon le type de contenu, ne pas s’afficher sur la télévision et l’appareil mobile.
TM
Wi-Fi
• Dans certains cas, en fonction des conditions de l’environnement des ondes radio ou de l’appareil mobile que vous utilisez, la vidéo et le son peuvent être interrompus.
• Dans certains cas, en fonction du contenu de la lecture et de l’environnement de connexion, la vidéo et le son peuvent être interrompus.
• Dans certains cas, si vous effectuez une manipulation sur votre appareil mobile, la vidéo et le son peuvent être interrompus.
• Veuillez confirmer l’environnement de connexion de Miracast/Wi-Fi Direct sur l’écran de connexion.
• Quand Miracast/Wi-Fi Direct est connecté, la connexion à Internet de cet appareil est interrompue temporairement.
Remarque
• Vous ne pouvez connecter simultanément qu’un seul périphérique mobile à l’appareil avec cette fonction.
• Si vous souhaitez connecter un autre appareil mobile, vous devez d’abord déconnecter celui qui est actuellement connecté.
• Si l’appareil est OFF (Veille), cette fonction se termine et les paramètres réseau repassent à ce qu’ils étaient avant d’utiliser cette fonction.
• Pour pouvoir utiliser cette fonction, votre dispositif mobile doit être équipé de la Wi-Fi.
• Cet appareil ne peut pas contrôler un dispositif mobile utilisant une application spéciale.
Affichage de l’écran du mode Miracast/Wi-Fi Direct
1 Mettez la TV sous tension.
2 Appuyez sur STANDBY/ON pour allumer cet appareil.
Le logo de Pioneer apparaît sur l’écran du téléviseur.
Remarque
• Si le logo de Pioneer n’apparaît pas, vérifiez les points suivants :
– Si cet appareil est en mode de lecture, appuyez sur
STOP.
– Si la page Home Media Gallery ou le menu
principal est affiché, appuyez sur HOME MENU pour dégager cette page.
3 Appuyez sur Miracast pour afficher l’écran du mode Miracast/Wi-Fi Direct.
• Le paramétrage pour connecter l’appareil et les dispositifs mobiles commence à partir de cet écran.
• Fermer cet écran termine la connexion Miracast/ Wi-Fi Direct.
• La reprise de la lecture sera automatiquement annulée si vous ouvrez cet écran.
05
31
Fr
Connexion par Miracast
05
Vous pouvez vous connecter à votre appareil mobile s’il dispose de la fonction Miracast conformément aux normes Wi-Fi.
Appuyez sur Miracast pour afficher l’écran du mode Miracast/Wi-Fi Direct.
• Certaines des fonctions de Miracast ont des noms différents selon l’appareil mobile. Pour des informations détaillées, consultez le mode d’emploi de l’appareil mobile.
1 Activez le paramétrage Miracast sur votre appareil mobile.
Une liste des appareils pouvant être connectés au périphérique mobile est affichée sur l’écran du périphérique mobile.
2 Sélectionnez le nom de périphérique “DIRECT­xxBD/BDP-80FD” pour l’appareil apparaissant sur Ecran TV depuis la liste affichée sur votre périphérique mobile.
“xx” indique le numéro d’identification du dispositif.
Attention
• Si le nom de l’appareil “DIRECT-xxBD/BDP-80FD” n’apparaît pas sur votre périphérique mobile, appuyez sur RETURN sur la télécommande puis sur Miracast et exécutez à nouveau les commandes depuis l’écran du mode Miracast/Wi-Fi Direct.
Si la connexion est réussie, l’écran de l’appareil mobile est également affiché sur la TV.
Remarque
• Pour les instructions concernant le fonctionnement de vos dispositifs mobiles, reportez-vous à leurs modes d’emploi.
Connexion à un appareil non compatible avec Miracast/ Wi-Fi Direct
Normalement connectez de la façon suivante.
1 Affichage de l’écran du mode Miracast/Wi-Fi Direct.
2 Dans les réglages de réseau Wi-Fi de votre dispositif mobile, sélectionnez le nom de cet appareil, comme indiqué sur lécran du téléviseur (“DIRECT-xxBD/BDP-80FD”).
“xx” indique le numéro d’identification du dispositif.
Attention
• Si le nom de l’appareil “DIRECT-xxBD/BDP-80FD” n’apparaît pas sur votre périphérique mobile, appuyez sur RETURN sur la télécommande puis sur Miracast et exécutez à nouveau les commandes depuis l’écran du mode Miracast/Wi-Fi Direct.
3 Sur votre dispositif mobile, saisissez le mot de passe de cet appareil, comme indiqué sur l’écran du téléviseur.
32
Fr
Remarque
• Pour les instructions concernant le fonctionnement de vos dispositifs mobiles, reportez-vous à leurs modes d’emploi.
Connexion par WPS
Si votre dispositif mobile supporte le WPS (connexion par bouton poussoir), il pourra être connecté.
1 Affichage de l’écran du mode Miracast/Wi-Fi Direct.
2 Utilisez / pour sélectionner WPS, puis appuyez sur ENTER.
3 Utilisez / pour sélectionner Next, puis appuyez ENTER.
4 En l’espace de 2 minutes, activez le réglage WPS du dispositif mobile.
Lorsque la connexion est établie, [Succès de la connexion] apparaît sur l’écran du téléviseur.
Remarque
• Pour les instructions concernant le fonctionnement de vos dispositifs mobiles, reportez-vous à leurs modes d’emploi.
5 Appuyez sur ENTER.
La connexion est établie. L’écran du mode Miracast/Wi-Fi Direct s’affiche.
Changez le SSID et le mot de passe
Changez le SSID et le mot de passe utilisés pour connecter l’appareil et un dispositif mobile.
1 Appuyez sur STANDBY/ON pour allumer l’appareil.
Le logo Pioneer apparaît sur l’écran de télévision.
2 Appuyez sur Miracast pour afficher l’écran du mode Miracast/Wi-Fi Direct.
3 Utilisez / pour sélectionner Refresh, puis appuyez sur ENTER.
Le SSID et le mot de passe sont changés. La connexion entre l'appareil et le dispositif mobile est
arrêtée.
Attention
• Tous les réglages de connexion effectués pour les dispositifs mobiles sont supprimés.
• Le SSID et le mot de passe ne changent pas sans mise à jour (Refresh). Vous devez régulièrement effectuer une mise à jour (Refresh) pour des raisons de sécurité.
Lorsque la connexion prend fin, vous devez reconfigurer aussi la connexion pour pouvoir utiliser à nouveau la fonction Miracast/Wi-Fi Direct.
Annuler la connexion Miracast/Wi-Fi Direct
1 Lorsque l’écran du mode Miracast/Wi-Fi Direct est affiché, appuyez sur RETURN.
• La connexion est annulée.
• Les paramètres réseau définis avant d’utiliser Miracast/Wi-Fi Direct sont rétablis.
Remarque
• Pour lire des disques, des périphériques USB ou des Contenu Web lors d’une connexion par Miracast/ Wi-Fi Direct, fermez l’écran du mode Miracast/Wi-Fi Direct.
Lecture des fichiers photo, musicaux ou vidéo du dispositif mobile
Envoyez les fichiers photo, musicaux ou vidéo du dispositif mobile à cet appareil.
Remarque
• Pour les instructions concernant le fonctionnement de vos dispositifs mobiles, reportez-vous à leurs modes d’emploi.
• Avec certains dispositifs mobiles, vous devrez installer un logiciel pour pouvoir transférer vos fichiers photo, musicaux ou vidéo.
• Selon le logiciel de l’appareil mobile, il peut ne pas fonctionner correctement.
05
33
Fr
Chapitre 6
06
Lecture de contenus web
Vous pouvez lire des contenus obtenus d’Internet via le lecteur.
Contenus web disponibles
•YouTube
• Picasa
Remarque
À propos de YouTube
• Ce lecteur prend en charge le service YouTube Leanback.
• Les vidéos YouTube pour téléphones portables ne peuvent pas être lues.
• Certaines vidéos YouTube ne peuvent pas être lues.
À propos de Picasa
• Picasa n’est disponible qu’en anglais. Reportez-vous au mode d’emploi à l’adresse http://picasa.google.com/support/ pour le détail.
– Enregistrez votre nom d’utilisateur et votre mot de
passe sur l’ordinateur avant d’utiliser Picasa Web Albums.
– La première fois que vous accédez à Picasa depuis
ce lecteur, sélectionnez l’icône New User et indiquez votre nom d’utilisateur et mot de passe.
• Selon l’environnement de la connexion Internet, il est possible que le contenu du site ne puisse pas être lu correctement.
• Pour accéder au contenu du site, ce lecteur doit disposer d’une connexion à haut débit. Pour utiliser une connexion Internet à haut débit, il faut être abonné à un fournisseur de service Internet.
• L’accès aux contenus fournis par des tiers exige une connexion Internet haut débit et peut aussi exiger la création d’un compte et des droits de souscription. Les services de contenus de tiers peuvent être changés, suspendus ou interrompus à tout moment sans préavis, et Pioneer décline toute responsabilité quant à ces changements. Pioneer ne certifie ou garantit que les services de contenus continueront d’être fournis ou disponibles pendant une période précise et décline toute garantie explicite ou implicite de ce type.
• La lecture de disque et cette fonction ne peuvent pas être utilisées en même temps.
À propos de la fonction limitant l’accès aux informations nuisibles sur Internet
• Cet appareil présente une fonction qui restreint l’affichage des contenus web, etc. qui ne doivent pas être vus par les enfants ou d’autres personnes.
• Pour utiliser cette fonction, les réglages Internet doivent être changés (page 38).
Lecture de contenus
• Le lecteur doit être raccordé à Internet au préalable. Reportez-vous à
l’interface LAN
1 Affichez l’écran de sélection.
Il est également possible d’afficher l’écran de sélection en appuyant sur HOME MENU puis en sélectionnant Contenu WebContenu Web souhaité.
2 Sélectionnez le type de contenu Web.
Utilisez / pour effectuer un choix, puis appuyez sur
ENTER.
3 Appuyez sur /// pour sélectionner le contenu que vous voulez lire, puis appuyez ENTER.
Appuyez sur STOP pour arrêter la lecture.
• Fin de lecture vidéo.
Utilisation de YouTube
1 Affichez l’écran de YouTube.
Appuyez sur YouTube.
• Pour Lecture/Arrêt/Fin, veuillez consulter
contenus
Attention
Raccordement au réseau par
à la page 18 pour le détail.
Lecture de
ci-dessus.
34
Fr
Chapitre 7
Réglages détaillés
Changement des réglages
07
Utilisation de la page Configuration initiale
1 Lorsque la lecture est arrêtée, affichez la page Home Menu.
Appuyez sur HOME MENU.
2 Sélectionnez et validez Configuration initiale.
Utilisez / pour effectuer un choix, puis appuyez sur ENTER.
Remarque
• Les paramètres pouvant être sélectionnés dépendent de l’état du lecteur.
• Dans Options, les réglages usine des paramètres sont indiqués en caractères gras.
Réglage Options Explication
Sortie Vidéo
Ecran TV 16:9 Plein Sélectionnez cette option si un téléviseur grand écran (16:9) est raccordé.
Réglages vidéo Standard Choisissez le mode de sortie vidéo.
Réduction du bruit 0 Choisissez le niveau de réduction du bruit.
16:9 Normal Sélectionnez cette option si un téléviseur grand écran (16:9) est raccordé. Les
4:3 Pan&Scan Sélectionnez cette option si un téléviseur 4:3 est raccordé et les vidéos lues
4:3 letterbox Sélectionnez cette option si un téléviseur 4:3 est raccordé et les vidéos lues
Vif Cinéma Personnalisé La qualité de l'image affichée peut être ajustée selon le téléviseur utilisé
1 2 3
images en 4:3 apparaissent avec des bandes verticales sur les côtés.
sont en 16:9. Les côtés gauche et droit de l’image seront tronqués pour que la vidéo puisse être vue sur l’écran 4:3. (Cette fonction agit si le disque porte la marque 4:3PS.)
sont en 16:9. Des bandes noires apparaîtront au haut et bas de l’image.
(page 39).
3 Sélectionnez le paramètre et changez son réglage.
Utilisez /// pour effectuer un choix, puis appuyez sur ENTER.
Fermeture de la page Configuration initiale
Appuyez sur HOME MENU ou RETURN.
35
Fr
07
Réglage Options Explication
Sortie Audio
Digital Out Bitstream Sélectionnez cette option pour transmettre directement les signaux audio
PCM Sélectionnez cette option pour transmettre des signaux audio numériques
Non-PCM Lors de la lecture d’un BD contenant un son secondaire et un son interactif,
Désactivé Sélectionnez cette option pour transmettre des signaux audio qui ne sont pas
Downmix Stéréo Les signaux audio surround convertis en signaux audio PCM linéraires sont
Lt/Rt Surround pour la sortie (lorsque le récepteur ou l’amplificateur AV, etc. est
Fréquence d’échantillonnage maximale
• Lors de la lecture d’un fichier ou d’un disque présentant une fréquence d’échantillonnage inférieure ou égale au réglage comparé au réglage actuel, vous pouvez le restituer avec la fréquence d’échantillonnage inchangée.
• Les sources dont les fréquences d’échantillonnage sont supérieures à 192 kHz ne peuvent pas être lues.
• Lors de la lecture de disques ou de fichiers protégés, les signaux sont restitués à une fréquence d’échantillonnage de 48 kHz ou moins, quel que soit ce réglage.
DRC (Dynamic Range Control)*
• Ceci agit sur les signaux audio comme les signaux Dolby Digital, Dolby TrueHD et Dolby Digital Plus.
• Le DRC agit sur les signaux audio provenant des prises de sortie suivantes : – Prises AUDIO OUT pour les signaux audio analogiques – Prises DIGITAL OUT ou HDMI OUT pour les signaux audio PCM linéaires
• Selon le disque, l’effet peut être faible.
• L’effet peut être différent selon les enceintes, les réglages de l’amplificateur AV, etc.
*
• Ceci agit sur les signaux audio comme les signaux Dolby Digital, Dolby TrueHD et Dolby Digital Plus.
• Le DRC agit sur les signaux audio provenant des prises de sortie suivantes : – Prises AUDIO OUT pour les signaux audio analogiques – Prises DIGITAL OUT ou HDMI OUT pour les signaux audio PCM linéaires
• Selon le disque, l’effet peut être faible.
• L’effet peut être différent selon les enceintes, les réglages de l’amplificateur AV, etc.
HDMI
Espace colorimétrique RGB Sélectionnez cette option pour restituer les signaux vidéo sous forme de
Résolution Auto Sélectionnez cette option pour que la résolution des signaux vidéo à la sortie
48k Restitue des signaux audio limités à une fréquence d’échantillonnage 96k 192k
Désactivé Sélectionnez cette option pour transmettre des signaux audio sans utiliser le
Activé Sélectionnez cette option pour régler la plage entre sons forts et sons faibles
Auto Sélectionnez cette option pour que le DRC s’active/désactive
YCbCr Sélectionnez cette option pour restituer les signaux sous forme de signaux
YCbCr 422 Sélectionnez cette option pour restituer les signaux sous forme de signaux
Full RGB Sélectionnez cette option pour restituer les signaux vidéo sous forme de
480I/576I Les signaux vidéo à la sortie de la prise HDMI OUT ont la résolution 480P/576P 720P 1080I 1080P
numériques.
convertis en signaux audio à 2 voies.
les deux signaux audio sont mixés et convertis en son Dolby Digital ou DTS avant leur sortie.
des signaux audio numériques.
convertis en signaux à 2 voies (stéréo) à la sortie.
compatible avec le Dolby Pro Logic, l’amplificateur ou l’amplificateur AV transmet les signaux audio PCM linéaires sous forme de signaux audio surround).
inférieure à la fréquence d’échantillonnage spécifiée pour la prise DIGITAL OUT. Sélectionnez la fréquence selon la performance de l’appareil raccordé.
contrôle de la plage dynamique.
(plage dynamique) lors de la lecture à volume modéré. Cette option permet de faire ressortir les dialogues et de regarder des films à faible volume la nuit.
automatiquement en fonction du signal audio du disque. Ceci n’agit que sur les signaux Dolby TrueHD.
signaux RGB. Choisissez cette option si les couleurs semblent faibles et le noir trop puissant.
YCbCr 4:4:4.
YCbCr 4:2:2.
signaux RGB. Choisissez cette option si les couleurs semblent trop denses et tous les dégradés de noir sont d’un noir uniforme.
de la prise HDMI OUT soit automatiquement sélectionnée.
sélectionnée. La résolution peut être changée en appuyant sur HDMI, mais Auto ne peut
pas être sélectionné. La résolution change chaque fois que vous appuyez sur HDMI.
36
Fr
Réglage Options Explication
HDMI
Sortie audio HDMI Bitstream Sélectionnez cette option pour transmettre directement les signaux audio
PCM Sélectionnez cette option pour transmettre des signaux audio HDMI convertis
Non-PCM Lors de la lecture d’un BD contenant un son secondaire et un son interactif,
Désactivé Sélectionnez cette option si vous ne voulez pas que les signaux audio soient
Control Activé Sélectionnez cette option pour activer la commande du lecteur via la
Désactivé Sélectionnez cette option pour désactiver la commande du lecteur via la
Pour utiliser les fonctions Sound Retriever Link et Stream Smoother Link (pages 15), Control doit être réglé sur Activé.
HDMI Deep Color 30 bits Sélectionnez cette option pour restituer les signaux vidéo en couleur 30 bits.
Lorsque [30 bits] ou [36 bits] est sélectionné, réglez l’espace colorimétrique (page 36) sur autre chose que YCbCr 422. HDMI 1080P 24Hz Activé Sélectionnez cette option lorsque la résolution est réglée sur Auto ou 1080P
HDMI 3D Auto Les disques 3D sont lus avec des images en 3D.
3D Notice Oui Précise si l’avis 3D doit être affiché ou non lors de la lecture d’images 3D.
Réseau
Réglage de l’adresse IP Sélectionnez cette option pour spécifier l’adresse IP du lecteur et du serveur DNS (page 39).
Serveur Proxy Ne réglez le serveur proxy que si votre fournisseur de service Internet vous le demande (page 39).
Information Indique les réglages de l’adresse MAC, l’adresse IP, le masque de sous-réseau, la passerelle par
Test de Connexion Sélectionnez cette option pour tester la connexion au réseau (page 40). Connexion BD-Live Autorisé Tous les disques peuvent se connecter à BD-LIVE.
DLNA Valider Sélectionnez cette option lorsque vous vous connectez à un serveur DLNA.
Interface Ethernet Sélectionnez cette option lorsqu’un câble LAN est utilisé pour la connexion
Réglage Sans fil Effectuez ces réglages pour une connexion sans fil au réseau (page 31).
Langue
OSD langues disponibles Choisissez une des langues indiquées pour l’affichage des pages.
Audio * Pour certains disques, il
peut être impossible de passer à la langue sélectionnée.
Si vous précisez une langue non enregistrée sur le BD ou le DVD, une des langues enregistrées sera automatiquement sélectionnée et utilisée.
Sous-titres * Pour certains disques, il
peut être impossible de passer à la langue sélectionnée.
Si vous précisez une langue non enregistrée sur le BD ou le DVD, une des langues enregistrées sera automatiquement sélectionnée et utilisée.
36 bits Sélectionnez cette option pour restituer les signaux vidéo en couleur 36 bits. Désactivé Sélectionnez cette option pour restituer les signaux vidéo en couleur normale
Désactivé Sélectionnez cette option lorsque la résolution est réglée sur 1080P et des
Désactivé Les images 3D ne sont pas lues.
Non
défaut, le serveur DNS (primaire) et le serveur DNS (secondaire).
Autorisé partiellement
Interdit Aucun disque ne peut se connecter à BD-LIVE.
Désactivé Sélectionnez cette option lorsque vous ne vous connectez pas à un serveur
Sans Fil Sélectionnez cette option pour une connexion sans fil au réseau.
langues disponibles Choisissez une des langues indiquées pour préciser la langue par défaut des
langues disponibles Choisissez une des langues indiquées pour préciser la langue par défaut des
HDMI.
en signaux audio PCM.
les deux signaux audio sont mixés et convertis en son Dolby Digital ou DTS avant leur sortie.
transmis par la prise de sortie HDMI.
télécommande de l’appareil AV raccordé à l’aide d’un câble HDMI. Reportez­vous aussi à page 15.
télécommande de l’appareil AV raccordé à l’aide d’un câble HDMI.
24 bits.
et des signaux vidéo 1080p/24 sont transmis à un téléviseur compatible avec le 1080p/24.
signaux vidéo 1080p/60 sont transmis à un téléviseur compatible avec le 1080p/60.
Seuls les disques dont la sécurité a été confirmée peuvent se connecter à BD­LIVE.
DLNA.
au réseau.
dialogues lors de la lecture de BD-ROM et de DVD-Vidéo.
sous-titres lors de la lecture de BD-ROM et de DVD-Vidéo.
07
37
Fr
07
Réglage Options Explication
Langue
Menu * Pour certains disques, il peut être impossible de passer à la langue sélectionnée.
Si vous précisez une langue non enregistrée sur le BD ou le DVD, une des langues enregistrées sera automatiquement sélectionnée et utilisée.
Lecture
Indicateur Angle Activé Sélectionnez cette option pour afficher la marque d’angle sur l’écran du
Indictateur PIP Activé Sélectionnez cette option pour afficher la marque PIP sur l’écran du
Indicateur second audio Activé Sélectionnez cette option pour afficher la marque de son secondaire sur
®
VOD DRM
DivX
Réglage Internet Autorisé Les contenus web peuvent être regardés sans avoir à saisir un mot de passe.
Pour limiter le visionnage de contenus web, etc. par les enfants ou d’autres personnes, sélectionnez [Autorisé partiellement] ou [Interdit].
Lecture automatique du Disque
Dernière mémoire Activé Sélectionnez cette option pour sauvegarder le point où la lecture a été
L’utilisation d’un disque qui ne supporte pas cette fonction n’est pas possible. PBC (Play Back Control) Activé Sélectionnez cette option pour lire les CD-vidéo (version 2.0) compatibles
Guide de Configuration Pour effectuer le paramétrage à partir du menu Setup Navigator. Pour le détail, reportez-vous à
Securité
Modification Mot Passe
Contrôle parental Changez le niveau du contrôle parental du lecteur (page 41). Code de pays Changez le code de pays/région (page 41).
Options
écran de veille Désactivé L’économiseur d’écran ne s’active pas.
Extinction automatique Désactivé Sélectionnez cette option si vous ne voulez pas que le lecteur s’éteigne de lui-
Démarrage rapide Activé Sélectionnez cette option pour réduire le temps de mise en route.
Mise à jour Via clé USB Sélectionnez cette option pour choisir la méthode de mise à jour du logiciel
Insérer les paramètres par défaut
Information Pour vérifier le numéro de version du système. BUDA Infos BUDA Pour afficher et configurer les données BUDA sur le dispositif USB raccordé
38
Fr
langues disponibles Choisissez une des langues indiquées pour préciser la langue par défaut des
Désactivé Sélectionnez cette option si la marque d’angle ne doit pas apparaître sur
Désactivé Sélectionnez cette option si la marque PIP ne doit pas apparaître sur l’écran
Désactivé Sélectionnez cette option si la marque de son secondaire ne doit pas
Code d’enregistrement:
Autorisé partiellement
Interdit Aucun contenu web ne peut être regardé.
Activé Les disques sont lus automatiquement après avoir été insérés. Désactivé Les disques insérés ne sont pas automatiquement lus.
Désactivé Sélectionnez cette option si vous voulez utiliser la poursuite du visionnage
Désactivé Sélectionnez cette option pour lire les CD-vidéo (version 2.0) compatibles
page 19. Enregistrez (changez) le mot de passe pour utiliser le contrôle parental ou l’annuler lors de la lecture
de DVD-Vidéo pourvus d’un contrôle parental (page 40). Le mot de passe par défaut est “0000”.
1 min • L’économiseur d’écran s’activera si aucune opération n’est effectuée 2 min 3 min
10 min L’alimentation est automatiquement coupée si aucune opération n’est 20 min 30 min
Désactivé Sélectionnez cette option pour une mise en route normale.
Réseau Pour rétablir les réglages usine.
Configuration BUDA
menus des BD-ROM et DVD-Vidéo.
téléviseur (page 23).
l’écran du téléviseur.
téléviseur.
du téléviseur.
l’écran du téléviseur (page 26).
apparaître sur l’écran du téléviseur. Indique le code d’enregistrement du lecteur requis pour la lecture de fichiers
DivX VOD (page 9).
Le mot de passe doit être saisi pour pouvoir regarder des contenus web.
arrêtée, même après l’ouverture du tiroir à disque ou la mise en attente.
(page 27).
avec la fonction PBC en utilisant le menu du disque.
avec la fonction PBC sans utiliser le menu du disque.
pendant plus d’une minute/deux minutes/trois minutes.
• Pendant le fonctionnement de l’économiseur d’écran, [SCNSVR] est affiché sur l’écran du panneau frontal.
• L’emploi de la télécommande peut désactiver l’économiseur d’écran.
même.
effectuée pendant plus de 10 minutes/20 minutes/30 minutes.
(page 41).
(page 40).
Réglage de l’image
1 Sélectionnez et validez Sortie Vidéo Réglages vidéo.
Utilisez / pour effectuer un choix, puis appuyez sur
ENTER.
2 Sélectionnez Personnalisé.
Utilisez / pour effectuer un choix, puis appuyez sur
ENTER.
3 Sélectionnez le paramètre et changez son réglage.
Utilisez / pour sélectionnez le paramètre puis utilisez / pour changer son réglage. Lorsque le réglage est
terminé, appuyez sur RETURN pour dégager l’écran de réglage.
Liste des paramètres
Paramètre Description
Luminosité Sélectionnez cette option pour régler la
Saturation Sélectionnez cette option pour régler la
Teinte Sélectionnez cette option pour régler
Contraste Sélectionnez cette option pour régler le
Netteté Choisissez le niveau de netteté. CTI (Color Transient
Improvement)
luminosité de l’écran du téléviseur.
saturation de l’écran du téléviseur.
l’équilibre des couleurs (vert et rouge) de l’écran du téléviseur.
contraste de l’écran du téléviseur.
Affiche des images aux couleurs bien distinctes.
Réglage de l’adresse IP
1 Sélectionnez et validez Réseau Réglage de l’adresse IP Ecran suivant.
Utilisez / pour effectuer un choix, puis appuyez sur
ENTER.
2 Spécifiez l’adresse IP.
Utilisez /// pour spécifier l’adresse IP du lecteur ou du serveur DNS, puis appuyez sur ENTER.
Réglage automatique de l'adresse IP Activé – L’adresse IP du lecteur est obtenue
automatiquement. Sélectionnez cette option lorsqu’un routeur ou un modem à la rge bande pourvu de la fonction DHCP (Protocole de configuration automatique) est utilisé. L’adresse IP de ce lecteur est automatiquement allouée par le serveur DHCP.
Désactivé – L’adresse IP du lecteur doit être spécifiée manuellement. Utilisez les touches numériques (0 à
9) pour saisir l’adresse IP, le masque de sous-réseau et la passerelle par défaut.
Attention
• Le réglage de l’adresse IP prend un certain temps.
Remarque
• Une fois que l’adresse IP spécifiée, sélectionnez [Test de connexion] pour vous assurer que l’appareil est connecté correctement.
• Pour de plus amples informations sur la fonction de serveur DHCP, reportez-vous au mode d’emploi du dispositif réseau.
• Si devrez éventuellement contacter votre fournisseur de service Internet ou votre administrateur réseau lors d’une saisie manuelle de l’adresse IP.
Réglage du serveur proxy
Ne réglez le serveur proxy que si votre fournisseur de service Internet vous le demande.
1 Sélectionnez et validez Réseau Serveur Proxy Ecran suivant.
Utilisez / pour effectuer un choix, puis appuyez sur
ENTER.
2 Sélectionnez et validez Utiliser ou Ne pas utiliser dans Proxy Server.
Utilisez / pour effectuer un choix, puis appuyez sur .
Utiliser – Sélectionnez cette option lorsque vous utilisez un serveur proxy.
Ne pas utiliser – Sélectionnez cette option lorsque vous n’utilisez pas de serveur proxy.
Si vous avez sélectionné Utiliser, passez au point 3.
3 Sélectionnez et validez Server Select Method.
Utilisez / pour effectuer un choix, puis appuyez sur .
Adresse IP – Précisez l’adresse IP.
Nom de serveur – Précisez le nom du serveur.
4 Précisez IP Address ou Server Name.
Utilisez les touches numériques (0 à 9) pour saisir le numéro si vous sélectionnez une adresse IP au point 3. Utilisez / pour déplacer le curseur.
Lorsque le nom du serveur est sélectionné au point 3, utilisez les touches numériques (0 à 9) pour afficher le clavier. Maintenant utilisez /// pour sélectionner les caractères et les paramètres, puis appuyez sur ENTER pour valider.
5 Entrée Numéro de port.
Appuyez sur , puis utilisez les touches numériques (0 à 9) pour préciser le nombre.
6 Appuyez sur ENTER pour valider.
Affichage des réglages du réseau
Sélectionnez et validez Réseau Information
Ecran suivant.
Utilisez / pour effectuer un choix, puis appuyez sur ENTER.
07
39
Fr
Les réglages de l’adresse MAC, l’adresse IP, le masque
07
de sous-réseau, la passerelle par défaut et le serveur DNS (primaire et secondaire) s’affichent.
Lorsque Réglage automatique de l'adresse IP est réglé sur Activé, les valeurs obtenues s’affichent automatiquement.
Remarque
• “0.0.0.0” s’affiche si aucune adresse IP n’a été spécifiée.
Test de la connexion au réseau
Sélectionnez et validez Réseau Test de connexion Démarrer.
Utilisez / pour effectuer un choix, puis appuyez sur ENTER.
“Réseau OK.” s’affiche lorsque le test est terminé. Si un autre message s’affiche, vérifiez les raccordements et/ou les réglages (pages 18 et page 39).
Changement de langue sous le paramètre Langue
1 Sélectionnez et validez Langue.
Utilisez / pour effectuer un choix, puis appuyez sur
ENTER.
2 Sélectionnez et validez OSD, Audio, Sous-titres ou Menu.
Utilisez / pour effectuer un choix, puis appuyez sur
ENTER.
3 Sélectionnez et validez la langue souhaitée.
Utilisez / pour effectuer un choix, puis appuyez sur ENTER.
Remarque
• Si vous précisez une langue non enregistrée sur le BD ou le DVD, une des langues enregistrées sera automatiquement sélectionnée et utilisée.
Effacement des données ajoutées aux BD et des données des applications
Procédez de la façon suivante pour effacer les données qui ont été ajoutées aux BD (données téléchargées avec la fonction BD-LIVE et données utilisées avec la fonction BONUSVIEW) et les données des applications.
2 Sélectionnez et validez Fmt buda. Appuyez sur ENTER.
Enregistrement ou changement du mot de passe
Procédez de la façon suivante pour enregistrer ou changer le code exigé pour le paramètre Parental Lock.
À propos du mot de passe par défaut de ce lecteur.
Le mot de passe par défaut est “0000”.
• Le lecteur peut vous demander de saisir un mot de passe lorsque vous changez de mot de passe.
• Si vous réinitialisez le lecteur, votre mot de passe reviendra au réglage par défaut.
1 Sélectionnez et validez Securité  Modification Mot Passe Ecran suivant.
Utilisez / pour effectuer un choix, puis appuyez sur
ENTER.
2 Précisez le mot de passe.
Utilisez les touches numériques (0 à 9) pour préciser le numéro, puis appuyez sur ENTER pour le valider.
Utilisez / pour déplacer le curseur.
3 Ressaisissez le mot de passe.
Utilisez les touches numériques (0 à 9) pour préciser le numéro, puis appuyez sur ENTER pour le valider.
Utilisez / pour déplacer le curseur.
• Pour changer le mot de passe, saisissez d’abord le mot de passe enregistré, puis saisissez le nouveau mot de passe.
Remarque
• Il est conseillé d’inscrire quelque part son mot de passe.
• Si vous avez oublié votre mot de passe, rétablissez les réglages par défaut du lecteur, puis enregistrez de nouveau votre mot de passe (page 42).
Attention
• L’effacement des données prend un certain temps.
• Ne débranchez pas le cordon d’alimentation pendant l’effacement des données.
1 Sélectionnez et validez Options  BUDA  Configuration BUDA.
Utilisez / pour effectuer un choix, puis appuyez sur
40
ENTER.
Fr
Loading...