Pioneer BCS-FS505 User Manual [en, de, es, fr, it]

Page 1
BCS-FS505
ENGLISH
FRANÇAIS
XV-BD505FS
S-BD505FS
DEUTSCH ITALIANO ESPAÑOL
NEDERLANDS
P/NO: MFL65220814
Page 2
2 Safety Information
1
Safety Information
Safety Information
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR BACK) NO
USER-SERVICEABLE PARTS INSIDE REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
This lightning  ash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of su cient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.
Cautions and Warnings
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
WARNING: Do not install this equipment in a con ned space such as a book case or similar unit.
CAUTION: Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from over heating. The openings shall be never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product shall not be placed in a built­in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instruction has been adhered to.
CAUTION: This product is a class 1 laser product classi ed under the Safety of laser products, IEC60825-1:2007. To ensure proper use of this product, please read this owner’s manual carefully and retain it for future reference. Shall the unit require maintenance, contact an authorized service centre.
Use of controls, adjustments or the performance of procedures other than those speci ed herein may result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try to open the enclosure. Visible laser radiation when open. DO NOT STARE INTO BEAM.
Page 3
3Safety Information
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon a dedicated circuit;
That is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the speci cation page of this owner’s manual to be certain. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or  re. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized service centre. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. To disconnect power from the mains, pull out the mains cord plug. When installing the product, ensure that the plug is easily accessible.
PIONEER hereby declares that this/ these product(s) is/are in compliance with the essential requirements and other relevant provisions of Directive 2004/108/EC, 2006/95/EC, and 2009/125/EC.
WARNING: To prevent a  re hazard, do not place any
naked  ame sources (such as a lighted candle) on the equipment.
This device is equipped with a portable battery or accumulator.
Safety way to remove the battery or the battery from the equipment: Remove the old battery
or battery pack, follow the steps in reverse order than the assembly. To prevent contamination of the environment and bring on possible threat to human and animal health, the old battery or the battery put it in the appropriate container at designated collection points. Do not dispose of batteries or battery together with other waste. It is recommended that you use local, free reimbursement systems batteries and accumulators. The battery shall not be exposed to excessive heat such as sunshine,  re or the like.
CAUTION: The apparatus shall not be exposed to water (dripping or splashing) and no objects  lled with liquids, such as vases, shall be placed on the apparatus.
1
Safety Information
Page 4
4 Safety Information
Information for users on collection and disposal of old equipment and used batteries
Safety Information
Symbol examples
for batteries
These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste.
For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points in accordance with your national legislation.
By disposing of these products and batteries correctly, you will help to save valuable resources and prevent any potential negative e ects on human health and the environment which could otherwise arise from inappropriate waste handling.
For more information about collection and recycling of old products and batteries, please contact your local municipality, your waste disposal service or the point of sale where you purchased the items.
These symbols are only valid in the European Union.
For countries outside the European Union:
If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal.
Notes on Copyrights
• Because AACS (Advanced Access Content System) is approved as content protection system for BD format, similar to use of CSS (Content Scramble System) for DVD format, certain restrictions are imposed on playback, analogue signal output,
Pb
etc., of AACS protected contents. The operation of this product and restrictions on this product may vary depending on your time of purchase as those restrictions may be adopted and/or changed by AACS after the production of this product.
• Furthermore, BD-ROM Mark and BD+ are additionally used as content protection systems for BD format, which imposes certain restrictions including playback restrictions for BD-ROM Mark and/or BD+ protected contents. To obtain additional information on AACS, BD-ROM Mark, BD+, or this product, please contact an authorized Customer Service Centre.
• Many BD-ROM/DVD discs are encoded with copy protection. Because of this, you should only connect your player directly to your TV, not to a VCR. Connecting to a VCR results in a distorted picture from copy-protected discs.
• This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Rovi Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Rovi Corporation. Reverse engineering or disassembly is prohibited.
• Under the U.S. Copyright laws and Copyright laws of other countries, unauthorized recording, use, display, distribution, or revision of television programmes, videotapes, BD-ROM discs, DVDs, CDs and other materials may subject you to civil and/or criminal liability.
Page 5
Important Notice for TV colour system
The colour system of this player di ers according to currently playing discs.
For example, when the player plays the disc recorded in the NTSC colour system, the image is output as an NTSC signal.
Only the multi system colour TV can receive all signals output from the player.
• If you have a PAL colour system TV, you will see just distorted images when using discs or video contents recorded in NTSC.
• The multi system colour TV changes the colour system automatically according to input signals. In case that the colour system is not changed automatically, turn it o and then on to see normal images on screen.
• Even if the disc recorded in NTSC colour system are well displayed on your TV, these may not be recorded correctly on your recorder.
5Safety Information
1
Safety Information
Page 6
6
Contents
3
Installation
16 Assemble the speakers 16 Assembling the speaker
1
Safety Information
2 Cautions and Warnings
2
Preparation
8 Introduction 8 About the “ ” Symbol
Display 8 Symbols Used in this Manual 9 Supplied Accessories 10 Playable Discs 11 File compatibility 12 Regional Code 12 AVCHD (Advanced Video
Codec High De nition) 12 Certain System Requirements 12 Compatibility Notes 13 Remote control 14 Front panel 15 Rear panel
18 Wall mounting the speakers 19 Additional notes on speaker 19 Positioning the system 20 Connecting to Your TV 21 HDMI Connection 22 Component Video
22 Video Connection 23 Resolution Setting 23 Antenna connection 24 Connections with external device 24 AUX Connection 24 PORTABLE IN connection 25 OPTICAL IN 1/2 connection 25 Bluetooth® connection 27 Connecting to your Home Network 28 Network Setup 30 USB device connection 31 Settings 31 Adjust the Setup Settings 32 [DISPLAY] Menu 34 [LANGUAGE] Menu 34 [AUDIO] Menu 35 [LOCK] Menu 36 [NETWORK] Menu 37 [OTHERS] Menu 38 Sound E ect
stands and securing your front speakers
Connection
Page 7
7
4
Operation
38 General Playback 40 Advanced Playback 42 On-Screen display 45 Enjoying BD-LIVE 46 Playing movie  le and VR discs 48 Viewing a photo 50 Listening to music 53 Playing the iPod 55 Radio Operations 56 Playing content via your home
network
5
Maintenance
60 Notes on Discs 60 Handling the Unit
6
Troubleshooting
61 General 62 Picture 62 Sound 63 Network
7
Appendix
64 Controlling a TV with the Supplied
Remote Control 65 Area Code List 66 Language code List 67 Video output resolution 68 Trademarks and Licences 70 Speci cations 71 Open source software notice
1
2
3
4
5
6
7
8
Page 8
8 Preparation
2 Preparation
Introduction
Preparation
About the “ ” Symbol Display
“ ” may appear on your TV display during operation and indicates that the function explained in this owner’s manual is not available on that speci c media.
Symbols Used in this Manual
NOTE
Indicates special notes and operating features.
CAUTION
Indicate cautions for preventing possible damages from abuse.
A section whose title has one of the following symbols are applicable only to the disc represented by the symbol.
BD
DVD
AVCHD
ACD
MOVIE
MUSIC
PHOTO
BD-ROM disc
DVD-Video, DVD±R/RW in Video mode or VR mode and  nalized
DVD±R/RW in AVCHD format
Audio CDs
Movie  les
Music  les
Photo  les
Page 9
9Preparation
Supplied Accessories
Video cable (1) Remote control (1)
Battery (1) FM antenna (1)
iPod cradle (1)
Accessaries of speaker box (S-BD505FS)
Speaker cables (3)
Large non-skid pads (1)
Speaker stand base (2)
Small screws (8)
Large screws (4)
Gasket (2)
2
Preparation
Poles (2)
Page 10
10 Preparation
Playable Discs
Preparation
Blu-ray Disc
- Discs such as movies that can be p
urchased or rented.
- BD-R/RE discs that contain Movie, Music or Photo  les.
DVD-VIDEO 8 / 12 cm disc Discs such as movies that can be purchased or rented.
DVD±R 8 / 12 cm disc
- Video mode and  nalized only
- Supports the dual layer disc
also
- Finalized AVCHD format
- DVD±R discs that contain Movie, Music or Photo  les
DVD-RW 8 / 12 cm disc
- VR mode, Video mode and
 nalized only
- Finalized AVCHD format
- DVD-RW discs that contain Movie, Music or Photo  les.
DVD+RW 8 / 12 cm disc
- Video mode and  nalized only
- AVCHD format
- Finalized AVCHD format
- DVD+RW discs that contain Movie, Music or Photo  les.
Audio CD 8 / 12 cm disc
CD-R/RW 8 / 12 cm disc
- CD-R/RW discs that contain audio titles, Movie, Music or Photo  les.
NOTE
• Depending on the conditions of the recording equipment or the CD-R/RW (or DVD±R/RW ) disc itself, some CD-R/RW (or DVD±R/RW) discs cannot be played on the unit.
• Depending on the recording software & the  nalization, some recorded discs (CD-R/RW, DVD±R/RW, BD-R/RE) may not be playable.
• BD-R/RE, DVD±R/RW and CD-R/RW discs recorded using a personal computer or a DVD or CD Recorder may not play if the disc is damaged or dirty, or if there is dirt or condensation on the player’s lens.
• If you record a disc using a personal computer, even if it is recorded in a compatible format, there are cases in which it may not play because of the settings of the application software used to create the disc. (Check with the software publisher for more detailed information.)
• This player requires discs and recordings to meet certain technical standards in order to achieve optimal playback quality.
• Pre-recorded DVDs are automatically set to these standards. There are many di erent types of recordable disc formats (including CD-R containing MP3 or WMA  les) and these require certain pre-existing conditions to ensure compatible playback.
• Customers should note that permission is required in order to download MP3 / WMA  les and music from the Internet. Our company has no right to grant such permission. Permission should always be sought from the copyright owner.
Page 11
11Preparation
File compatibility
Overall
Available File extensions:
“.jpg”, “.jpeg”, “.png”, “.avi”, “.divx ”, “.mpg”, “.mpeg”, “.mkv”, “.mp4”, “.mp3”, “.wma”, “.wav ”
• Available  le extensions di er depending on the DLNA servers.
Some “.wav”  les are not supported on this
player.
The  le name is limited to 180 characters.
Depending on the size and number of the
 les, it may take several minutes to read the contents on the media.
Maximum Files/Folder: Less than 2 000 (total number of  les and folders)
CD-R/RW, DVD±R/RW, BD-R/RE Format:
ISO 9660+JOLIET, UDF and UDF Bridge format
MOVIE
Available resolution size:
1 920 x 1 080 (W x H) pixels Playable subtitle: SubRip (.srt / .txt), SAMI (.smi), SubStation Alpha (.ssa/.txt), MicroDVD (.sub/.txt), VobSub (.sub), SubViewer 1.0 (.sub), SubViewer 2.0 (.sub/.txt), TMPlayer (.txt), DVD Subtitle System (.txt)
• VobSub (.sub) is not available in the [Home Link] feature.
Playable Codec format: “DIVX3.xx”, “DIVX4. xx”, “DIVX5.xx”, “XVID”, “DIVX6.xx ” (Standard playback only), H.264/MPEG-4 AVC, MPEG1 SS, MPEG2 PS, MPEG2 TS Playable Audio format: “Dolby Digital”, “DTS”,
“MP3”, “WMA”, “AAC”, “AC3”
• Not all the WMA and AAC Audio formats are compatible with this unit.
Sampling frequency: between 32 kHz to 48 kHz (WMA), between 16 kHz to 48 kHz (MP3) Bit rate: between 20 kbps to 320 kbps (WMA), between 32 kbps to 320 kbps (MP3)
NOTE
• HD movie  les contained on the CD or USB
1.0/1.1 may not played properly. BD, DVD or USB
2.0 are recommended to play back HD movie  les.
• This player supports H.264/MPEG-4 AVC pro le Main, High at Level 4.1. For a  le with higher level, the warning message will appear on the screen.
• This player does not support the  les that are recorded with GMC encoding techniques in MPEG4 standard, like DivX or XVID have.
*1 GMC – Global Motion Compensation *2 Qpel – Quarter pixel
1
or Qpel
*
2
. Those are video
*
MUSIC
Sampling frequency: between 8 kHz to 48 KHz (WMA), between 11 kHz to 48 kHz (MP3) Bit rate: between 8 kbps to 320 kbps (WMA, MP3),
NOTE
• This unit cannot support the ID3 Tag embedded MP3  le.
• The total playback time indicated on the screen may not be correct for VBR  les.
PHOTO
Recommended size:
Less than 4,000 x 3,000 x 24 bit/pixel Less than 3,000 x 3,000 x 32 bit/pixel Less than 4 MByte/ le
• Progressive and lossless compression photo image  les are not supported.
2
Preparation
Page 12
12 Preparation
Regional Code
This unit has a regional code printed on the rear of the unit. This unit can play only BD-ROM or DVD discs labeled same as the rear of the unit or “ALL”.
AVCHD (Advanced Video Codec High De nition)
Preparation
• This player can playback AVCHD format discs. These discs are normally recorded and used in camcorders.
• The AVCHD format is a high de nition digital video camera format.
• The MPEG-4 AVC/H.264 format is capable of compressing images at higher e ciency than that of the conventional image compressing format.
• Some AVCHD discs use the “x.v.Colour” format.
• This player can playback AVCHD discs using “x.v.Colour” format.
• Some AVCHD format discs may not play, depending on the recording condition.
• AVCHD format discs need to be  nalized.
• “x.v.Colour” o ers a wider colour range than normal DVD camcorder discs.
Certain System Requirements
For high de nition video playback:
• High de nition display that has COMPONENT or HDMI input jacks.
• BD-ROM disc with high de nition content.
• HDMI or HDCP capable DVI input on your display device is required for some content (as speci ed by disc authors).
• For up-conversion of standard de nition DVD, a HDMI or HDCP capable DVI input on your display device is required for copy protected content.
Compatibility Notes
• Because BD-ROM is a new format, certain disc, digital connection and other compatibility issues are possible. If you experience compatibility problems, please contact an authorized Customer Service Centre.
• Viewing high-de nition content and up­converting standard DVD content may require a HDMI-capable input or HDCP­capable DVI input on your display device.
• Some BD-ROM and DVD discs may restrict the use of some operation commands or features.
• You can use a USB device that is used to store some disc related information, including downloaded on-line content. The disc you are using will control how long this information is retained.
Page 13
Remote control
1
2
3
13Preparation
• • • • • • • • • a • • • • • • • • •
(STANDBY/ON): Switches the
1
player ON or OFF.
OPEN/CLOSE: Opens and closes
Z
the disc tray.
INPUT/TUNER: Changes input
mode. BT AUDIO: Changes input mode to
BT AUDIO directly. OPTICAL: Changes input mode to
optical directly.
DISPLAY: Displays or exits On-
Screen Display.
HOME MENU: Displays or exits
the [Home Menu]. MENU: Accesses the menu on a
disc. Direction buttons: Selects an
option in the menu.
ENTER: Acknowledges menu
selection.
Battery Installation
Remove the battery cover on the rear of the Remote Control, and insert a R03 (size AAA) battery with and matched correctly.
TUNE (+/-): Tunes in the desired radio station.
PRESET: Selects programme of Radio.
• • • • • • • • • b • • • • • • • • •
RETURN: Exits the menu or
O
resumes playback. POPUP/ TOP MENU: Displays the
DVD title menu or BD-ROM’s pop­up menu, if available.
STOP: Stops playback.
x
PLAY: Starts playback.
B
PAUSE/STEP: Pauses playback
X ./>
or previous chapter / track /  le.
m/M
backward or forward. SPK LEVEL: Sets the sound level of
desired speaker.
z
SKIP: Goes to the next
SCAN: Searches
USB REC: Records an audio CD.
MUTE: Mute the unit. SOUND: Selects a sound e ect
mode. VOL +/- : Adjusts speaker volume.
• • • • • • • • • c • • • • • • • • •
0-9 numerical buttons: Selects numbered options in a menu.
MARKER: Marks any point during playback.
SEARCH: Displays or exits the search menu.
REPEAT: Repeats a desired
section or sequence. CLEAR: Removes a mark on the
search menu or a number when setting the password.
DIMMER: Dims the light on the unit.
ZOOM: Accesses the zoom menu. Coloured (A, B, C, D) buttons: Use
to navigate on menus.
- A button (RDS): Radio Data System.
- B button (PTY): Views the programme type of the RDS.
- C button (PTY SEARCH): Searches programme type.
- D button: Selects MONO or STEREO in FM mode.
TV Control Buttons: See page 64. SLEEP: Sets a certain period of time
after which the unit will switch to o .
2
Preparation
Page 14
14 Preparation
Front panel
Preparation
a
b
1
Disc Tray
Operation buttons
1
STANDBY/ON Button
Z
(OPEN/CLOSE)
FUNCTION
Changes the input source or function
B/X
(PLAY / PAUSE)
x
(STOP)
./>
(SKIP)
- TUNE + (Radio tuning)
3 4 5 6 7
Remote sensor
c
Display window
d
PORTABLE IN
e
USB Port
f
Volume control
g
2
Page 15
Rear panel
1 2 3 4 5
15Preparation
2
Preparation
6 7 8 9 10 11
AC Power cord
a
Plug into the power source.
Speakers connectors
b
Cooling Fan
c
Antenna Connector
d
VIDEO OUT
e
AUX (L/R) INPUT
f
COMPONENT VIDEO (Y PB PR)
g
OUTPUT (PROGRESSIVE SCAN)
OPTICAL IN 1(TV) / 2
h
iPod (24 pin)
i
Connect to the furnished iPod cradle.
HDMI OUT (type A, Version 1.3)
j
Connect to TV with HDMI inputs.
LAN port
k
Page 16
16 Installation
3 Installation
Assemble the speakers
Installation
For subwoofer:
Use the supplied adhesive to attach four large pads to the base of subwoofer.
Assembling the speaker stands and securing your front speakers
1. Insert the pole from the holes behind
the base and secure with the 4 screws.
large non-skid pads
2. A x the gasket to the pole. A x the gasket to the surface of the pole where the speaker will be mounted.
Page 17
17Installation
3. Insert the speaker cord from the hole behind the base through to the pole and connect it to the speaker terminal. After connecting, put the speaker wire in the gap on the back side of the speaker.
Match the colour tube on the wire with the
colour indicator on the label, then insert the white wire with gray line into the red (+) side and the other wire into the black (-) side.
5. After connecting, put the speaker wire in the back of the base of the stand.
6. Connect the wires to the player.
Connect the white wire with gray line into
(+) side and the other wire into (–) side. To connect the cable to the player, press each plastic  nger pad to open the connection terminal. Insert the wire and release the  nger pad.
Red (+)
Orange (+)
Black (–)
White (+)
3
Installation
4. Secure the speaker and the pole with 2 screws.
Ensure that the speaker wire does not get pinched between the speaker and the pole.
CAUTION
• Do not connect any speakers other than those supplied to this system.
• Do not connect the supplied speakers to any ampli er other than the one supplied with this system. Connection to any other ampli er may result in malfunction or  re.
Page 18
18 Installation
Wall mounting the speakers
Before mounting
Remember that the speaker system is heavy and that its weight could cause the screws to work loose, or the wall material to fail to support it, resulting in the speaker falling. Make sure that the wall you intend to mount the speakers on is strong enough to support them. Do not mount on plywood or soft surface walls.
Mounting screws are not supplied. Use screws suitable for the wall material and support the weight of the speaker.
Installation
CAUTION
• If you are unsure of the qualities and strength of the wall, consult a professional for advice.
• Pioneer is not responsible for any accidents or damage that result from improper installation.
Mounting Screw (Not supplied)
\GGG^G
\G
XWG


Attaching the speakers
The front speaker can be hung vertically or horizontally on the wall. Use one hole to hang it vertically and two holes to hang it horizontally. The illustration below shows the front right speaker.
}GG
o
o¡GG
o
When installing the speaker horizontally, set it up so that the speaker terminal on the back side of the speaker is on the outside on the end of the surface, farthest away from the other speaker.
GzGz
GmGm
NOTE
Do not connect the supplied speakers to any ampli er other than the one supplied with this system. Connection to any other ampli er may result in malfunction or  re.
Page 19
Additional notes on speaker
A
B
C
A
A
D
Install the main front left and right speakers at an equal distance from the TV.
Precautions:
Make sure that all the bare speaker wire is twisted together and inserted fully into the speaker terminal. If any of the bare speaker wire touches the back panel it may cause the power to cut o as a safety measure.
The front speakers supplied with this system are magnetically shielded. However, depending on the installation location, colour distortion may occur if the speaker is installed extremely close to the screen of a television set. If this case happens, turn the power switch of the television set OFF, and turn it ON after 15 min. to 30 min. If the problem persists, place the speaker system away from the television set.
The subwoofer is not magnetically shielded and so should not be placed near a TV or monitor. Magnetic storage media (such as  oppy discs and tape or video cassettes) should also not be kept close to the subwoofer.
Do not attach the front speakers and subwoofer to a wall or ceiling. They may fall o and cause injury.
Front left speaker (L)/
A
Front right speaker (R):
B
Place the front speakers to the sides of the monitor or screen and as  ush with the screen surface as possible.
Subwoofer:
C
The position of the subwoofer is not so critical, because low bass sounds are not highly directional. But it is better to place the subwoofer near the front speakers. Turn it slightly toward the centre of the room to reduce the wall re ections.
Unit
D
CAUTION
19Installation
3
Installation
Positioning the system
The following illustration shows an example of positioning the system. Note that the illustrations in these instructions di er from the actual unit for explanation purposes. For the best possible surround sound, all the speakers other than the subwoofer should be placed at the same distance from the listening position (A).
• Be careful to make sure children do not put their hands or any objects into the *subwoofer duct. *subwoofer duct: A hole for plentiful bass sound on subwoofer cabinet (enclosure).
• The speakers contain magnet parts, so colour irregularity may occur on the TV screen or PC monitor screen. Please use the speakers away from the TV screen or PC monitor screen.
Page 20
20 Installation
Connecting to Your TV
Make one of the following connections, depending on the capabilities of your existing equipment.
• HDMI connection (pages 20-21)
• Component Video connection (page 21)
• Video connection (page 22)
NOTE
Installation
• Depending on your TV and other equipment you wish to connect, there are various ways you could connect the player. Use only one of the connections described in this manual.
• Please refer to the manuals of your TV, stereo system or other devices as necessary to make the best connections.
• Make sure the player is connected directly to the TV. Tune the TV to the correct video input channel.
• Do not connect your player via your VCR. The image could be distorted by the copy protection system.
HDMI Connection
If you have a HDMI TV or monitor, you can connect it to this player using a HDMI cable(Type A, Version 1.3). Connect the HDMI OUT jack on the player to the HDMI IN jack on a HDMI compatible TV or monitor.
HDMI Connection
Player
Player
TV
TV
Set the TV’s source to HDMI (refer to TV’s Owner’s manual).
Page 21
21Installation
NOTE
• Changing the resolution when the connection has already been established may result in malfunctions. To solve the problem, turn o the player and then turn it on again.
• When the HDMI connection with HDCP is not veri ed, TV screen is changed to black screen. In this case, check the HDMI connection, or disconnect the HDMI cable.
• If there is noise or lines on the screen, please check the HDMI cable (length is generally limited to 4.5 m and use a high speed HDMI cable (version 1.3).
• If a connected HDMI device does not accept the audio output of the device’s audio sound may be distorted or may not output.
• When you use HDMI connection, you can change the resolution for the HDMI output. (Refer to “Resolution Setting” on page 22.)
• Select the type of video output from the HDMI OUT jack using [HDMI Color Setting] option on the [Setup] menu (see page 33).
• When you connect a HDMI or DVI compatible device make sure of the following:
- Try switching o the HDMI/DVI device and this
player. Next, switch on the HDMI/DVI device and leave it for around 30 seconds, then switch on this player.
- The connected device’s video input is set
correctly for this unit.
- The connected device is compatible with
720x576p (480p), 1280x720p, 1920x1080i or 1920x1080p video input.
• Not all HDCP-compatible HDMI or DVI devices will work with this player.
- The picture will not be displayed properly with
non-HDCP device.
- This player does not playback and TV screen is
changed to black screen.
player, the HDMI
Component Video Connection
Connect the COMPONENT VIDEO OUT jacks on the player to the corresponding input jacks on the TV using Y Pb Pr cables. You can hear the sound the through the system’s speaker.
Component Connection
Player
Player
PR
VIDEO
L
PB
AUX
R
Y
COMPONENT
VIDEO
INPUT
OUTPUT
Green
Green Blue
Blue
Red
Red
TV
TV
NOTE
When you use COMPONENT VIDEO OUT connection, you can change the resolution for the output. (Refer to “Resolution setting” on page 22.)
3
Installation
Page 22
22 Installation
Video Connection
Connect the VIDEO OUT jack on the player to the video in jack on the TV using a video cable. You can hear the sound through the system’s speakers.
Video Connection
Player
PR
VIDEO
Yellow
Yellow
L
PB
AUX
R
Y
COMPONENT
VIDEO
INPUT
OUTPUT
Installation
TV
TV
Resolution Setting
The player provides several output resolutions for HDMI OUT and COMPONENT VIDEO OUT jacks. You can change the resolution using [Setup] menu.
1. Press HOME MENU (
2. Use I/
i/U/u
to select the [Setup] and
press ENTER (
3. Use U/u to select [DISPLAY] option then press i to move to the second level.
4. Use U/u to select the [Resolution] option then press ENTER ( third level.
5. Use U/u to select the desired resolution then press ENTER ( selection.
).
). The [Setup] menu appears.
) or i to move to the
) to con rm your
NOTE
• If your TV does not accept the resolution you have set on the player, you can set resolution to 576p (480p) as follows:
1. Press Z to open the disc tray.
2. Press x for more than 5 seconds.
• Since several factors a ect the resolution of video output, see “Video Output Resolution” on page 67.
Page 23
23Installation
Antenna connection
Connect the supplied antenna for listening to the radio.
Antenna Connection
Player
Player
Connections with external device
AUX Connection
You can enjoy the sound from an external component through the speakers of this system.
Connect the analogue audio output jacks of your component into the AUX L/R (INPUT) on this unit. And then select the [AUX] option by pressing INPUT/TUNER, I/i and ENTER (
AUX Connection
Player
Player
PR
VIDEO
L
PB
AUX
R
Y
COMPONENT
INPUT
).
VIDEO
3
Installation
NOTE
After connecting the FM wire antenna, keep it as horizontal as possible. Be sure to fully extend the FM wire antenna.
Red
Red
White
White
To the audio output jacks
To the audio output jacks
of your component
of your component
(TV, VCR, etc.)
(TV, VCR, etc.)
Page 24
24 Installation
PORTABLE IN connection
OPTICAL IN 1/2 connection
You can enjoy the sound from your portable audio player through the speakers of this system.
Connect the headphones (or line out ) jack of the portable audio player into the PORTABLE IN socket of this unit. And then select the [PORTABLE] option by pressing INPUT/TUNER, I/i and ENTER (
PORT.IN Connection
Installation
You can enjoy the sound from your component with a digital optical connection through the speakers of this system.
Connect the optical output jack of your component into the OPTICAL IN 1/2 jacks on the unit. And then select the [OPTICAL 1/2] option by pressing INPUT/TUNER, I/i and
).
ENTER (
Optical Connection
). Or press OPTICAL to select directly.
To the digital
To the digital
optical output jack
optical output jack
of your component
of your component
twZGSGUUU
Page 25
25Installation
Bluetooth® connection
About Bluetooth
Bluetooth® is wireless communication technology for short range connection.
The available range is within 10 meters. (The sound may be interrupted when the connection interfered by the other electronic wave or you connect the bluetooth in the other rooms.) Connecting individual devices under Bluetooth wireless technology does not incur any charges. A mobile phone with Bluetooth wireless technology can be operated via the Cascade if the connection was made via Bluetooth wireless technology.
Available Devices : Mobile phone, MP3, Laptop, PDA (This units be supported the Stereo Headset.)
Bluetooth Pro les
In order to use Bluetooth wireless technology, devices must be able to interpret certain pro les. This unit is compatible with following pro le.
A2DP (Advanced Audio Distribution Pro le)
Listening to music of a Bluetooth device
Pairing your unit and Bluetooth device
Before you start the pairing procedure, make sure the Bluetooth feature is turned on in to your Bluetooth device. Refer to your Bluetooth device’s user guide. Once a pairing operation is performed, it does not need to be performed again.
1. Select the Bluetooth function by using the INPUT/TUNER or BT AUDIO. Appears “BT AUDIO” and then “BT READY” in display window.
2. Operate the Bluetooth device and perform the pairing operation. When searching for this unit with the Bluetooth device, a list of the devices found may appear in the Bluetooth device display depending on the type of Bluetooth device. Your unit appears as “PIONEER AUDIO”.
3. Enter the PIN code. PIN cord : 0000
4. When this unit successfully paired with your Bluetooth device, Bluetooth LED of this unit lights up and appears “BT SINK”.
NOTE
Depending on the Bluetooth device type, some device have a di erent pairing way.
5. Listening to music. To play a music stored on your Bluetooth device, refer to your Bluetooth device’s user guide.
NOTE
• If you change the function of the unit, the Bluetooth function is disconnected, operate pairing again.
• AVRCP cannot be available in this mode.
3
Installation
Page 26
26 Installation
Checking the information of connected Bluetooth device
This function is operated after pairing. You can check the Bluetooth information.
Press DISPLAY repeatedly.
Bluetooth information is changed as follows. Local Bluetooth Device Address t Device Name t None t ...
Installation
NOTE
• This units dose not be supported the Mono
Headset Pro le (Hands Free Pro le).
• The sound may be interrupted when the
connection interfered by the other electronic wave.
• You cannot control the Bluetooth device with
this unit.
• Pairing is limited one Bluetooth device per one
unit and multi-pairing is not supported.
• Although the distance between your Bluetooth
and the set is less than 10 m, there are obstacles between both, your Bluetooth device cannot be connected.
• Depending on the type of the device, you may
not be able to use the Bluetooth function.
• When not connected the Bluetooth, “BT READY”
appears on the display window.
• The Electrical malfunction due to devices using
same frequency such as Medical equipment, Microwaves or wireless LAN devices, the connection will be disconnected.
• When someone stands and interrupts
communication between Bluetooth device and the player, the connection will be disconnected.
• If the gotten away of the distance between
Bluetooth and the unit, the sound quality is lower and lower the connection will disconnect when the space between the Bluetooth and the unit gets out of the operating range of Bluetooth.
• The device with Bluetooth wireless technology
is disconnected, if you turn o the main unit or put the device away from the main unit more than 10 m.
Page 27
27Installation
Connecting to your Home Network
This player can be connected to a local area network (LAN) via the LAN port on the rear panel.
Please refer to the documentation for your network device for further instructions. Connect the player’s LAN port to the corresponding port on your Modem or Router using a commercially available LAN or Ethernet cable (CAT5 or better with RJ45 connector). In the example con guration for wired connection below, this player would be able to access content from either of the PCs.
Network Connection
Router
Router
WAN
LAN 1
LAN 2
LAN 3
PC
PC
Player
Player
Broadband
Broadband
Service
Service
3
Installation
NOTE
• When plugging or unplugging the LAN cable, hold the plug portion of the cable. When unplugging, do not pull on the LAN cable but unplug while pressing down on the lock.
• Do not connect a modular phone cable to the LAN port.
• Since there are various connection con gurations, please follow the speci cations of your telecommunication carrier or internet service provider.
• If you want to access content from PCs or DLNA servers, this player must be connected to the same local area network with them via a router.
Page 28
28 Installation
Network Setup
Before setting the wired network, you need to connect the broadband internet to your home network.
If there is a DHCP server on the local area network (LAN) via wired connection, this player will automatically be allocated an IP address. After making the physical connection, a small number of home networks may require the player’s network setting to be adjusted. Adjust the [NETWORK] setting as follows.
1. Select [Connection Setting] option in the [Setup] menu then press ENTER (
Installation
2. Use U/u/I/ between [Dynamic] and [Static]. Normally, select [Dynamic] to allocate an IP address automatically.
i
to select the IP mode
NOTE
If there is no DHCP server on the network and you want to set the IP address manually, select [Static] then set the [IP Address], [Subnet Mask], [Gateway] and [DNS Server] using U/u/I/ buttons. If you make a mistake while entering a number, press CLEAR to clear the highlighted part.
3. Select [OK] and press ENTER ( ) to apply network settings.
4. The player will ask you to test the network
).
connection. Select [OK] and press ENTER
) to complete the network connection.
(
5. If you select [Test] and press ENTER ( ) at step 4 above, the network connection status is displayed on the screen. You can also test it on the [Connection Status] in the [Setup] menu.
i
and numerical
Page 29
29Installation
Notes on Network Connection:
• Many network connection problems during set up can often be  xed by re-setting the router or modem. After connecting the player to the home network, quickly power o and/or disconnect the power cable of the home network router or cable modem. Then power on and/or connect the power cable again.
• Depending on the internet service provider (ISP), the number of devices that can receive internet service may be limited by the applicable terms of service. For details, contact your ISP.
• Our company is not responsible for any malfunction of the player and/or the internet connection feature due to communication errors/malfunctions associated with your broadband internet connection, or other connected equipment.
• The features of BD-ROM discs made available through the Internet Connection feature are not created or provided by our company, and our company is not responsible for their functionality or continued availability. Some disc related material available by the Internet Connection may not be compatible with this player. If you have questions about such content, please contact the producer of the disc.
• Some internet contents may require a higher bandwidth connection.
• Even if the player is properly connected and con gured, some internet contents may not operate properly because of internet congestion, the quality or bandwidth of your internet service, or problems at the provider of the content.
• Some internet connection operations may not be possible due to certain restrictions set by the Internet service provider (ISP) supplying your broadband Internet connection.
• Any fees charged by an ISP including, without limitation, connection charges are your responsibility.
• A 10 Base-T or 100 Base-TX LAN port is required for wired connection to this player. If your internet service does not allow for such a connection, you will not be able to connect the player.
• You must use a Router to use xDSL service.
• A DSL modem is required to use DSL service and a cable modem is required to use cable modem service. Depending on the access method of and subscriber agreement with your ISP, you may not be able to use the internet connection feature contained in this player or you may be limited to the number of devices you can connect at the same time. (If your ISP limits subscription to one device, this player may not be allowed to connect when a PC is already connected.)
• The use of a “Router” may not be allowed or its usage may be limited depending on the policies and restrictions of your ISP. For details, contact your ISP directly.
• Turn o all unused network equipment in your local home network. Some devices may generate network tra c.
3
Installation
Page 30
30 Installation
USB device connection
This player can play movie, music and photo  les contained in the USB device.
1. Insert a USB device to the USB port until it  ts into place.
USB Connection
Installation
2. Press HOME MENU. Select [Movie], [Photo] or [Music] using
U/u/I/i
3. Select a  le using U/u/I/i, and press PLAY or ENTER ( You can check the space of the USB device on the screen.
4. Select the other mode. And withdraw the USB device carefully.
, and press ENTER ( ).
) to play the  le.
NOTE
• This player supports USB  ash memory/external HDD formatted in FAT16, FAT32 and NTFS when accessing  les (music, photo, movie). However, for BD-LIVE and Audio CD recording, only FAT16 and FAT32 formats are supported. Use the USB  ash memory/external HDD formatted in either FAT16 or FAT32 when using BD-LIVE and Audio CD recording.
• The USB device can be used for local storage for enjoying BD-Live discs from the Internet.
• This unit can support up to 4 partitions of the USB device.
• Do not extract the USB device during operation (play, etc.).
• An USB device which requires additional programme installation when you have connected it to a computer, is not supported.
• USB device: USB device that support USB 1.1 and USB 2.0.
• Movie, music and photo  les can be played. For details of operations on each  le, refer to relevant pages.
• Regular back up is recommended to prevent data loss.
• If you use a USB extension cable, USB HUB or USB Multi-reader, the USB device may not be recognised.
• Some USB device may not work with this unit.
• Digital camera and mobile phone are not supported.
• The USB Port on this unit cannot be connected to a PC.
Page 31
31Installation
Settings
Adjust the Setup Settings
You can change the settings of the player in the [Setup] menu.
1. Press HOME MENU (
2. Use I/
i/U/u
to select [Setup] and press
ENTER ( ). The [Setup] menu appears.
).
4. Use U/u to select a second setup option, and press ENTER ( level.
5. Use U/u to select a desired setting, and press i or ENTER ( ) to con rm your selection.
) to move to the third
3
Installation
3. Use U/u to select a  rst setup option, and press i to move to the second level.
Page 32
32 Installation
[DISPLAY] Menu
TV Aspect Ratio
Select a TV aspect ratio option according to your TV type.
[4:3 Letter Box]
Select when a standard 4:3 TV is connected. Displays theatrical images with masking bars above and below the picture.
[4:3 Pan Scan]
Select when a standard 4:3 TV is connected. Displays pictures cropped to  ll your TV screen. Both sides of the picture are cut o .
Installation
[16:9 Original]
Select when a 16:9 wide TV is connected. The 4:3 picture is displayed with an original 4:3 aspect ratio, with black bars appearing at the left and right sides.
[16:9 Full]
Select when a 16:9 wide TV is connected. The 4:3 picture is adjusted horizontally (in a linear proportion) to  ll the entire screen.
Resolution
Sets the output resolution of the Component and HDMI video signal. Refer to page 22 and 67 or details about the resolution setting.
[Auto]
If the HDMI OUT jack is connected to TVs providing display information (EDID), this automatically selects the resolution best suited to the connected TV. If the COMPONENT VIDEO OUT only is connected, this changes the resolution to 1080i as default resolution.
[1080p]
Outputs 1080 lines of progressive video.
[1080i]
Outputs 1080 lines of interlaced video.
[720p]
Outputs 720 lines of progressive video.
[576p (480p)]
Outputs 576 (480) lines of progressive video.
[576i (480i)]
Outputs 576 (480) lines of interlaced video.
NOTE
You cannot select [4:3 Letter Box] and [4:3 Pan Scan] option when the resolution is set to higher than 720p.
Page 33
33Installation
1080p Display Mode
When the resolution is set to 1080p, select [24 Hz] for smooth presentation of  lm material (1080p/ 24 Hz) with a HDMI-equipped display compatible with 1080p/ 24 Hz input.
NOTE
• When you select [24 Hz], you may experience some picture disturbance when the video switches video and  lm material. In this case, select [50 Hz].
• Even when [1080p Display Mode] is set to [24 Hz], if your TV is not compatible with
1080p/ 24 Hz
the video output will be 50 Hz to match the video source format.
, the actual frame frequency of
HDMI Color Setting
Select the type of output from the HDMI OUT jack. For this setting, please refer to the manuals of your display device.
[YCbCr]
Select when connecting to a HDMI display device.
[LANGUAGE] Menu
Display Menu
Select a language for the [Setup] menu and on-screen display.
Disc Menu/ Disc Audio/ Disc Subtitle
Select the language you prefer for the audio track (disc audio), subtitles, and the disc menu.
[Original]
Refers to the original language in which the disc was recorded.
[Other]
Press ENTER ( Use number buttons then ENTER ( ) to enter the corresponding 4-digit number according to the language code list on page 66.
[O ] (for Disc Subtitle only)
Turn o Subtitle.
) to select another language.
3
Installation
[RGB]
Select when connecting to a DVI (RGB) display device.
NOTE
Depending on the disc, your language setting may not work.
Page 34
34 Installation
[AUDIO] Menu
Speaker Setup
To obtain the best possible sound, use the speaker setup display to specify the volume of the speakers you have connected and their distance from your listening position. Use the test to adjust the volume of the speakers to the same level.
[Speaker]
Select a speaker that you want to adjust.
[Volume]
Adjust the output level of each speaker.
Installation
[Distance]
Adjust the distance between each speaker and the listening position.
[Test/ Stop test tone]
The speakers will emit a test tone.
[OK]
Con rms the setting.
[Cancel]
Cancels the setting.
HD AV Sync
Sometimes Digital TV encounters a delay between picture and sound. If this happens you can compensate by setting a delay on the sound so that it e ectively ‘waits’ for the picture to arrive: this is called HD AV Sync. Use scroll up and down through the delay amount, which you can set at anything between 0 and 300 ms.
The delay will vary depending on which digital TV channel you are on. If you change channel you may need to readjust the HD AV Sync.
U u
to
DRC (Dynamic Range Control)
When a title encoded in Dolby Digital or Dolby Digital Plus is playing back, you may wish to compress the dynamic range of the audio output (the di erence between the loudest sounds and the quietest ones). This allows you to listen to a movie at a lower volume without losing clarity of sound. Set [DRC] to [On] for this e ect.
NOTE
The DRC setting can be changed only when a disc is not inserted or the unit is in complete stop mode.
Page 35
35Installation
[LOCK] Menu
To access any features in the [LOCK] settings, you must enter the 4-digit security code you have created. If you have not entered a password yet, you are prompted to do so. Enter a 4-digit password twice, and press ENTER ( password.
Password
You can create or change the password.
[None]
Enter a 4-digit password twice, and press ENTER (
[Change]
Enter the current password and press ENTER ( press ENTER ( ) to create a new password.
) to create a new password.
). Enter a 4-digit password twice, and
NOTE
If you make a mistake before pressing ENTER press CLEAR. Then input the correct password.
If you forget your password,
) to create a new
( )
,
DVD Rating
Blocks playback of rated DVD based on their content. (Not all discs are rated.)
[Rating 1-8]
Rating one (1) has the most restrictions and rating eight (8) is the least restrictive.
[Unlock]
If you select this, parental control is not active and the disc plays in full.
BD Rating
Sets an age limit for BD-ROM playback. Use number buttons to input an age limit for BD-ROM viewing.
[255]
All BD-ROM can be played.
[0-254]
Prohibits play of BD-ROM with corresponding ratings recorded on them.
NOTE
The [BD Rating] will be applied only for the BD disc that containing the Advanced Rating Control.
3
Installation
If you forget your password, you can clear it using the following steps:
1. Remove any disc that might be in the player.
2. Select [Lock] option in the [Setup] menu.
3. Use number buttons to enter “210499” on the
[Lock] Menu. The password is cleared.
Area Code
Enter the code of the area whose standards were used to rate the DVD video disc, based on the list on page 65.
Page 36
36 Installation
[NETWORK] Menu
Connection Setting
If your home network environment is ready to connect to the player, the player needs to be set up for network communication. (See “Connecting to your Home Network” on page 27.)
Connection Status
If you want to check the network status on this player, select the [Connection Status] option and press ENTER ( ) to check whether a connection to the network and the internet
Installation
has been established.
BD-LIVE connection
You can restrict Internet access when BD-LIVE functions are used.
[Permitted]
Internet access is permitted for all BD-LIVE contents.
[Partially permitted]
Internet access is permitted only for BD­LIVE contents which have content owner certi cates. Internet access and AACS Online functions are prohibited for all BD­LIVE contents without a certi cate.
[OTHERS] Menu
DivX VOD
ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, Inc. This is an o cial DivX Certi ed device that plays DivX video. Visit www.divx.com for more information and software tools to convert your  les into DivX video.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certi ed® device must be registered in order to play DivX Video-on-Demand (VOD) content. To generate the registration code, locate the DivX VOD section in the device setup menu. Go to vod.divx.com with this code to complete the registration process and learn more about DivX VOD.
[Register]
Displays the registration code of your player.
[Deregister]
Deactivate your player and display the deactivation code.
NOTE
All the downloaded videos from DivX VOD with this player’s registration code can only be played back on this unit.
[Prohibited]
Internet access is prohibited for all BD-LIVE contents.
Page 37
37Installation
Auto Power O
The screen saver appears when you leave the player in Stop mode for about  ve minutes. If you set this option to [On], the unit automatically turns itself o after the Screen Saver is displayed for 25 minutes. Set this option to [O ] to leave the screen saver until the unit is operated by the user.
Initialize
Factory Set
You can reset the player to its original factory settings.
BD Storage Clear
Removes the BD contents from the connected USB storage.
NOTE
If you reset the player to its original factory settings using [Factory Set] option, you have to set all the activation for the on-line services and network settings again.
Software Information
Displays the current software version.
Sound E ect
You can select a suitable sound mode. Press SOUND repeatedly until the desired mode appears on the front panel display or the TV screen. The displayed items for the equalizer maybe di erent depending on sound sources and e ects.
[Pioneer]: You can enjoy comfortable and natural sound.
[Bypass]: Software with multichannel surround audio signals is played according to the way it was recorded.
[Bass Blast]: Reinforce the bass sound e ect from front left and right speaker and subwoofer.
[Clear Voice]: This mode makes voice sound clear, improving the quality of voice sound.
[Game]: You can enjoy more virtual sound while playing video games.
[Night]: This may be useful when you want to watch movies at low volumes late at night.
[Mus. ReTouch]: When listening to MP3  les or other compressed music, you can enhance the sound. This mode is available only to 2 channel sources.
[Loudness]: Improves bass and treble sound.
3
Installation
Page 38
38 Operation
4 Operation
General Playback
Playing Discs
1. Press Z OPEN/CLOSE, and place a disc on
the disc tray.
Operation
2. Press Z OPEN/CLOSE to close the disc tray. For most Audio CD, BD-ROM and
DVD-ROM discs, playback starts automatically.
3. Press
HOME MENU.
4. Select [Movie], [Photo] or [Music] using
U/u/I/i
5. Select the Disc option using I/i, and press ENTER (
When you connect up to two devices, it appears as above.
6. Select a  le using U/u/I/i, and press B PLAY or ENTER (
• Playback functions described in this manual are not always available in every  les and medium. Some functions can be restricted depending on many factors.
• Depending on the BD-ROM titles, a USB device connection may be needed for proper playback.
, and press ENTER ( ).
).
) to play the  le.
NOTE
Page 39
39Operation
To stop playback
Press x STOP during playback.
To pause playback
Press X PAUSE/STEP during playback. Press B PLAY to resume playback.
To play frame-by-frame
Press X PAUSE/STEP while movie playback. Press X PAUSE/STEP repeatedly to playback Frame-by-Frame.
To scan forward or backward
Press m or M to play fast forward or fast reverse during playback. You can change the various playback speeds by pressing m or M repeatedly.
To slow down the playing speed
While the playback is paused, press M SCAN repeatedly to play various speeds of slow motion.
To skip to the next/previous chapter/track/ le
During playback, press . or > to go to the next chapter/track/ le or to return to the beginning of the current chapter/track/ le. Press . twice brie y to step back to the previous chapter/track/ le.
Using the disc menu
BD DVD AVCHD
To display the disc menu
The menu screen may be displayed  rst after loading a disc which contains a menu. If you want to display the disc menu during playback, press MENU.
Use U/u/I/i buttons to navigate through menu items.
To display the Pop-up menu
Some BD-ROM discs contain a Pop-up menu that appears during playback.
Press POPUP/ TOP MENU during playback, and use U/u/I/i buttons to navigate through menu items.
Resume playback
BD DVD AVCHD MOVIE ACD
MUSIC
This unit remembers the x STOP depending on the disc. If “
(Resume Stop)” appears on the screen
Xx
brie y, press B (PLAY) to resume playback (from the scene point).
If you press x (STOP) twice or unload the disc, “x”(Complete Stop) appears on the screen. The unit will clear the stopped point.
4
Operation
NOTE
• The resume point may be cleared when a button is pressed (for example; 1 (POWER),
(OPEN/CLOSE), etc).
Z
• On BD-Video discs with BD-J, the resume playback function does not work.
• If you press x (STOP) once during BD-ROM interactive title playback, the unit will be in Complete Stop mode .
Page 40
40 Operation
Advanced Playback
Repeat Playback
BD DVD AVCHD ACD MUSIC
During playback, press REPEAT ( to select a desired repeat mode.
BDs/DVDs
– Selected portion will be repeated
A-
continually.
Chapter
played back repeatedly.
Title
back repeatedly.
To return to normal playback, press REPEAT (
Operation
Audio CDs/Music  les
played back repeatedly.
back repeatedly.
– The tracks or  les will be played back in
random order.
played back repeatedly in random order.
continually. (Audio CD only)
To return to normal playback, press CLEAR.
• If you press > once during Repeat Chapter/ Track playback, the repeat playback cancels.
• This function may not work on some disc or title.
– The current chapter will be
– The current title will be played
) repeatedly to select [O ].
– The current track or  le will be
– All the tracks or  les will be played
– All the tracks or  les will be
– Selected portion will be repeated
NOTE
) repeatedly
Repeating a speci c portion
BD DVD AVCHD ACD
This player can repeat a portion you have selected.
1. During playback, press REPEAT ( [A-] at the beginning of the portion you wish to repeat. And then press ENTER ( ).
2. Press ENTER ( Your selected portion will be repeated continually.
3. To return to normal playback, press REPEAT
) repeatedly to select [OFF] or press
( CLEAR.
) at the end of the portion.
) to select
NOTE
You cannot select a portion less than 3 seconds.
Marker Search
BD DVD AVCHD MOVIE
You can start playback from up to nine memorized points.
To enter a marker
1. During playback, press MARKER at the
desired point. The Marker icon appears on the TV screen brie y.
2. Repeat step 1 to add up to nine markers.
To recall a marked scene
1. Press SEARCH and the search menu appears
on the screen.
2. Press a number button to select a marker number that you want to recall. Playback starts from the marked scene.
Page 41
41Operation
To delete a Marker
1. Press SEARCH and the search menu appears
on the screen.
2. Press u to highlight a marker number. Use
I/i
to select a marked scene that you
want to delete.
3. Press CLEAR and the marked scene is erased from the search menu.
NOTE
• This function may not work depending on discs, titles, server ability.
• All marked points are cleared if the title is in complete stop (x) mode, the title is changed or if you unload the disc.
• If the total length of the title is less than 10 seconds, this function is not available.
Using the search menu
BD DVD AVCHD MOVIE
Using search menu, you can easy to  nd the point where you want to start playback.
To start playback from a marked scene
1. Press SEARCH and the search menu appears
on the screen.
2. Press u to highlight a marker number. Use
I/i
to select a marked scene that you
want to playback from.
3. Press ENTER ( ) to start playback from the marked scene.
NOTE
• This function may not work depending on discs, titles, server ability.
• This function may not work on some [Home Link] contents depending on the  le type and ability of the DLNA server.
Last Scene Memory
BD DVD
This unit memorizes the last scene from the last disc that is viewed. The last scene remains in memory even if you remove the disc from the unit or switch o the unit. If you load a disc that has the scene memorized, the scene is automatically recalled.
4
Operation
To search a point
1. During playback, press SEARCH to display
the search menu.
2. Press I/i to skip the playback 15 seconds forward or backward. You can select a point that you want to skip by pressing and holding I/i button.
NOTE
• Last Scene Memory function for a previous disc is erased once a di erent disc is played.
• This function may not work depending on the disc.
• This unit does not memorize settings of a disc if you switch o the unit before commencing to play it.
Page 42
42 Operation
On-Screen display
You can display and adjust various information and settings concerning the content.
Displaying content information on-screen
BD DVD AVCHD MOVIE
1. During playback, press DISPLAY (
various playback information.
Operation
Title – Current title number/total number
a
of titles Chapter – Current chapter number/total
b
number of chapters Time – Elapsed playing time/Total
c
playback time Audio – Selected audio language or
d
channel Subtitle – Selected subtitle
e
Angle – Selected angle/total number of
f
angles TV Aspect Ratio – Selected a TV aspect
g
Ratio Picture Mode – Selected picture mode
h
a b c
d
e f
g h
) to show
2. Select an option using U/u.
3. Use I/i to adjust the selected option
value.
4. Press RETURN (O) to exit the On-Screen display.
NOTE
• If no button is pressed for a few seconds, the on­screen display disappears.
• A title number cannot be selected on some discs.
• Available items may di er depending on discs or titles.
• If BD interactive title is playing back, some setting information is displayed on the screen but prohibited to be changed.
Page 43
43Operation
Playing from selected time
BD DVD AVCHD MOVIE
1. Press DISPLAY ( ) during playback. The
time search box shows the elapsed playing time.
2. Select the [Time] option and then input the required start time in hours, minutes, and seconds from left to right.
For example, to  nd a scene at 2 hours, 10 minutes, and 20 seconds, enter “21020”.
Press I/i to skip the pl forward or backward.
3. Press ENTER (
) to start playback from
selected time.
NOTE
• This function may not work on some disc or titles.
• This function may not work on some [Home Link] contents depending on the  le type and ability of the DLNA server.
ayback 60 seconds
Hearing di erent audio
BD DVD AVCHD MOVIE
1. During playback, press DISPLAY ( ) to
display the on-screen display.
2. Use U/
3. Use I/
u
to select the [Audio] option.
i
to select desired audio language,
audio track or audio channel.
NOTE
• Some discs allow you to change audio selections only via the disc menu. If this is the case, press POPUP/ TOP MENU or MENU button and choose the appropriate audio from the selections on the disc menu.
• Immediately after you have switched sound, there may be a temporary discrepancy between the display and actual sound.
Selecting a subtitle language
BD DVD AVCHD MOVIE
1. During playback, press DISPLAY ( ) to
display the on-screen display.
2. Use U/
3. Use I/
u
to select the [Subtitle] option.
i
to select the desired subtitle
language.
4. Press RETURN (O) to exit the On-Screen display.
4
Operation
NOTE
Some discs allow you to change subtitle selections only via the disc menu. If this is the case, press POPUP/ TOP MENU or MENU button and choose the appropriate subtitle from the selections on the disc menu.
Page 44
44
Operation
Watching from a di erent angle
BD DVD
If the disc contains scenes recorded at di erent camera angles, you can change to a di erent camera angle during playback.
1. During playback, press DISPLAY ( display the on-screen display.
display.
u
to select the [Angle] option.
i
to select desired angle.
2. Use U/
3. Use I/
4. Press RETURN (O) to exit the On-Screen
Changing the TV Aspect Ratio
BD DVD AVCHD MOVIE
You can change the TV aspect ratio setting during playback.
Operation
1. During playback, press DISPLAY ( display the on-screen display.
option.
display.
u
to select the [TV Aspect Ratio]
i
to select desired option.
2. Use U/
3. Use I/
4. Press RETURN (O) to exit the On-Screen
Changing the Picture Mode
BD DVD AVCHD MOVIE
You can change the [Picture mode] option during playback.
1. During playback, press DISPLAY (
) to
display the on-screen display.
option.
display.
u
to select the [Picture Mode]
i
to select desired option.
2. Use U/
3. Use I/
4. Press RETURN (O) to exit the On-Screen
Setting the [User setting] option
) to
1. During playback, press DISPLAY ( ) to display the on-screen display.
2. Use U/
3. Use I/
u
to select the [Picture Mode]
option.
i
to select the [User setting] option,
and press ENTER (
).
) to
NOTE
Even if you change the value of the [TV Aspect Ratio] option in On-Screen display, the [TV Aspect Ratio] option in the [Setup] menu is not changed.
4. Use U/u/I/ options.
Select [Default] option then press ENTER ( ) to reset the all adjustments.
5. Use U/u/I/ and press ENTER (
i
to adjust the [Picture Mode]
i
to select the [Close] options,
) to  nish setting.
Page 45
Operation
45
Enjoying BD-LIVE
This unit allows you to enjoy functions such as picture-in-picture, secondary audio and Virtual packages, etc., with BD-Video supporting BONUSVIEW (BD-ROM version 2 Pro le 1 version 1.1/ Final Standard Pro le).
Secondary video and audio can be played from a disc compatible with the picture-in-picture function. For the playback method, refer to the instructions in the disc.
In addition to the BONUSVIEW function, BD­Video supporting BD-LIVE (BD-ROM version 2 Pro le 2) that has a network extension function allows you to enjoy more functions such as downloading new movie trailers by connecting this unit to the internet.
1. Check the network connection and settings (page 27).
2. Insert a USB storage device to the USB port on the front panel.
A USB storage device is needed to download bonus content.
USB Connection
3 . Press HOME MENU, and set the [BD-LIVE
connection] option on the [Setup] menu (page 36).
Depending on the disc, the BD-LIVE function may not operate if [BD-LIVE connection] option is set to [Partially Permitted].
4 . Insert a BD-ROM with BD-LIVE.
The operations may di er depending on the disc. Refer to the manual supplied with the disc.
NOTE
• Do not extract the connected USB device while content is being downloaded or a Blu-ray disc is still in the disc tray. Doing so may damage the connected USB device and BD-LIVE features may not operate properly with the damaged USB device anymore. If the connected USB device seems damaged from such an action, you can format the connected USB device from the PC and reuse it with this player.
• Some BD-LIVE contents may be restrictively accessed in some territories by contents provider’s own decision.
• It may take up to several minutes to load and start enjoying BD-LIVE contents.
4
Operation
Page 46
46
Operation
Playing movie  le and VR discs
You can play DVD-RW discs that are recorded in Video Recording (VR) format and movie  les contained in a disc or USB device.
1. Press
2. Select [Movie] using U/u/I/i, and press
Operation
ENTER ( ).
3. Select the device using I/i, and press ENTER ( ).
HOME MENU.
NOTE
• The  le requirements are described on page 11.
• You can use various playback functions. Refer to pages 38-44.
• Un nalized DVD VR format discs may not be played in this player.
• Some DVD-VR disc are made with CPRM data by DVD recorder. This unit cannot support these kinds of discs.
What is CPRM?
CPRM is a copy protection system (with scramble system) only allowing the recording of ‘copy once’ broadcast programmes. CPRM stands for Content Protection for Recordable Media.
When you connect up to two devices, it appears as above.
4. Select a  le using U/u/I/i, and press PLAY or ENTER ( ) to play the  le.
B
Page 47
Operation
47
Selecting a subtitle  le
MOVIE
If a movie  le name and the subtitle  le name are the same, subtitle  le is played automatically when playing the movie  le.
If the subtitle  le name is di erent with the movie  le name, you need to select the subtitle  le on the [Movie] menu before playing the movie.
NOTE
i
to select the subtitle  le you
).
1. Use U/u/I/ wish to play in the [Movie] menu.
2. Press ENTER ( Press ENTER ( ) again to deselect the
subtitle  le. Selected subtitle  le will be displayed when you play the movie  le.
• If you press x STOP during playback, the subtitle selection is cancelled.
• This function may not work in the [Home Link] feature.
Changing subtitle code page
MOVIE
If the subtitle is not displayed properly, You can change the subtitle code page to view the subtitle  le properly.
1. During playback, press DISPLAY ( display the on-screen display.
display.
u
to select the [Code Page] option.
i
to select desired code option.
2. Use U/
3. Use I/
4. Press RETURN (O) to exit the On-Screen
) to
4
Operation
Page 48
48
Operation
Viewing a photo
You can view photo  les using this player.
1. Press
2. Select [Photo] using I/i, and press ENTER
( ).
3. Select the device using I/i, and press ENTER ( ).
Operation
HOME MENU
To play a slide show
Press B PLAY to start slide show.
To stop a slide show
Press x STOP during slide show.
To pause a slide show
Press X PAUSE/STEP during slide show. Press B PLAY to re-start the slide show.
To skip to the next/previous photo
While viewing a photo in full screen, press I or
i
to go to the previous or next photo.
NOTE
• The  le requirements are described on page 11.
• You can use various playback functions. Refer to pages 38-44.
When you connect up to two devices, it appears as above.
4. Select a  le using U/u/I/i, and press ENTER ( ) to view the photo.
Page 49
Operation
49
Options while viewing a photo
You can use various options while viewing a photo in full screen.
1. While viewing a photo in full screen, press DISPLAY (
2. Select an option using U/u.
Current photo/Total number of photos
a
– Use I/i to view previous/next photo. Slide Show – Press ENTER (
b
pause slide show. Music Select – Select the background
c
music for the slide show. Music –Press ENTER (
d
background music. Rotate – Press ENTER (
e
photo clockwise. Zoom – Press ENTER (
f
[Zoom] menu. E ect – Use I/i to select a transition
g
e ect between photos in a slide show. Speed – Use I/i to select a delaying
h
speed between photos in a slide show.
) to display the option menu.
a
b c d e
f g
h
) to start or
) to start or pause
) to rotate the
) to display the
Listening to music during a slide show
You can display photo  les while listening to music  les.
1. Press
2. Select [Photo] or [Home Link] using
U/u/I/i
3. Select the [Disc] or [USB] option using I/i,
and press ENTER ( ).
Selecting a server or a share folder is needed for [Home Link] menu.
4. Select a  le using U/u/I/i, and press ENTER ( ) to view the photo.
5. Press menu.
6. Use U/u to select [Music Select] option, and press ENTER ( Select] menu.
HOME MENU
, and press ENTER ( ).
DISPLAY ( ) to display the option
) to display the [Music
4
Operation
3. Press RETURN (O) to exit the option menu.
Page 50
50
Operation
7. Use U/u to select a device, and press ENTER ( ).
Devices that you can select may di er depending on the location of the photo  le you are displaying in full screen.
Photo location Available Device
Disc Disc, USB USB Disc, USB Share Folder on
your PC (CIFS) DLNA server DLNA server
8. Use U/u to select a  le or a folder you wish to play.
Operation
Select a folder and press ENTER ( ) to display the lower directory.
Select the upper directory.
and press ENTER ( ) to display
CIFS
Listening to music
The player can play Audio CDs and music  les
1. Press
2. Select [Music] using U/u/I/i, and press
ENTER ( ).
3. Select the device using I/i, and press ENTER ( ).
HOME MENU
NOTE
When selecting music from [Home Link], folder selection is not available. Only  le selection is available on the [Home link].
9. Use i to select [OK], and press ENTER ( ) to complete music selection.
When you connect up to two devices, it appears as above.
4. Select a music  le or audio track using
U/u/I/i
music.
, and press ENTER (
) to play the
NOTE
• The  le requirements are described on page 11.
• You can use various playback functions. Refer to pages 38-44.
Page 51
Operation
51
Audio CD Recording
You can record one desired track or all of the tracks in Audio CD to a USB storage device.
1. Insert a USB storage device to the USB port on the front panel.
2. Press Z (OPEN/CLOSE), and place an Audio CD on the disc tray.
Press Z (OPEN/CLOSE) to close the disc tray. The playback starts automatically.
3. Press DISPLAY ( ) to display the option menu.
Or
Press z USB REC button on the remote
control. You can record all musics in the audio CD.
4. Use U/u to select [CD Recording] option, and press ENTER ( Recording] menu.
Repeat this step to select tracks as many as you want.
5. Use U/u to select a track you wish to copy on the menu, and press ENTER (
Repeat this step to select tracks as many as you can.
) to display the [CD
).
6. Use U/u/I/i to select [Start], and press ENTER (
7. Use U/u/I/i to select the destination folder to be copied.
If you want to create a new folder, use U/u/
I/i
( ). Enter a folder name using the virtual
keyboard, and press ENTER ( ) while [OK] is selected.
8. Use U/u/I/i to select [OK], and press ENTER (
If you want to stop the Audio CD recording, press ENTER ( ) while [Cancel] is highlighted.
9. A message appears when Audio CD recording is completed. Press ENTER ( to check the music  le created in the destination folder.
).
to select [New Folder] and press ENTER
) to start Audio CD recording.
4
Operation
)
Select all the tracks on an Audio CD.
Selects an encoding option from the pop-up menu (128 kbps, 192 kbps, 320 kbps or Lossless).
Cancels the recording and returns to the previous screen.
Page 52
52
Operation
NOTE
• The table below shows the average recording time from an audio track with 4 minutes of playback time to a music  le with 192 kbps as an example.
stop mode during playback
1.4 min. 2 min.
• All times in the above table are approximate.
• Actual recording time for USB storage device varies depending on the USB storage device’s ability.
• Make sure that there is minimum of 50 MB free space when recording into the USB storage device.
• The length of the music should be longer than 20 seconds for the proper recording.
• Do not turn o this player or extract the
Operation
connected USB storage device during Audio CD recording.
The making of unauthorized copies of
copy-protected material, including computer
programmes,  les, broadcasts and sound
recordings, may be an infringement of copyrights
and constitute a criminal o ense.
This equipment should not be used
for such purposes.
Be responsible
Respect copyrights
Page 53
Operation
53
Playing the iPod
You can enjoy the sound with your iPod. For details about iPod, refer to the iPod’s User Guide.
Preparation
• To view iPod’s Videos and Photos on the TV screen.
- Be sure to use the video connection
through the VIDEO OUT jack on the rear panel of this unit. Select the appropriate video input mode on the TV.
- Depending on the iPod, make sure that
select Videos > Video settings, and then set TV Out to Ask or On from your iPod. For details about Video Settings, refer to the iPod User Guide.
- The viewing photos is available only if this
unit is in iPod IN mode and you can view photos only as a slide show. You have to start a slide show on your iPod to view a photo on a TV. For details about a slide show, refer to the iPod User Guide.
• Before connecting the iPod, turn this unit o and reduce the volume of this unit to its minimum.
1. Connect the iPod  rmly.
Connect the iPod
Connect the cradle and put your iPod on it.
2. Select a  le using U/u/I/i, and press ENTER (
) to play the  le.
Enjoying iPod on the screen
1. Connect the iPod  rmly.
2. Press HOME MENU ( ).
3. Select [Music] or [Movie] using I/i, and
press ENTER ( ).
If you connected the other device (CD or USB), select the iPod on the menu.
4. Select a content using U/u/I/i, and press ENTER (
) to play.
4
Operation
Page 54
54
Operation
Enjoying the iPod IN mode
You can operate your iPod by using the supplied remote control and controls on your iPod.
1. Connect the iPod  rmly. If you turn this unit on, your iPod is automatically turned on and recharging starts.
2. Press INPUT/TUNER to select iPod IN mode.
U/u/I/i
B
/ENTER
X
m/M
Operation
./>
REPEAT To select a desired repeat
This system is compatible with the audio and video of the iPod(4th generation), iPod nano, iPod classic, iPod mini, iPod touch and iPhone (iPod shu e is not supported.).
Selects an option in the menu.
Starts playback the music or video.
To pause while it is playing. To resume playing, press again.
Fast-forward or rewind a song or video
Skip the playback forward or backward .
mode: Track
( )
(No display).
NOTE
, All
B
( )
(PLAY)
, O
NOTE
• An error message “CHECK IPOD” or “Connected iPod model is not supported.” appears when:
- your iPod is not available for the function to be
operated.
• An error message “CHECK IPOD” or “Please update iPod’s software.” appears when:
- your iPod has an old software version.
t
Update your iPod software to latest version.
• If this unit displays an error message, follow the message. An error message “CHECK IPOD” or “Please check your iPod.” appears when:
- the communication between this unit and
your iPod is failed.
t
Undock & re-dock your iPod in this unit.
- your iPod is not connected  rmly.
- this unit recognises your iPod as unknown
device.
- your iPod is exceptionally low on power.
t
The battery needs to be charged.
t
If you charge the battery while iPod is
extremely low in power, it may take longer to charge.
• You may use the dock adapter which should be supplied with your iPod to the dock for the stable use of the iPod. If you need an adapter, consult your iPod dealer.
• Compatibility with your iPod may vary depending on the type of your iPod.
• iPod touch and iPhone have any di erence in operation other than iPod. You may need any additional control to use them with this unit. (e.g. “slide to unlock”)
• If you use an application, make a call, or send and receive SMS text message, etc. on iPod touch or iPhone, disconnect it from iPod dock of this unit and then use it.
• Depending on your iPod’s software version, it may not be possible to control your iPod from this unit. We recommend installing the latest software version.
• The video quality depends on the video sources on your iPod.
• If you have a problem with your iPod, please visit www.apple.com/support/ipod.
Page 55
Operation
55
Radio Operations
Be sure that the antenna is connected. (Refer to the page 23)
Listening to the radio
1. Press INPUT/TUNER until TUNER (FM)
appears in the display window. The last received station is tuned in.
2. Press and hold TUNE (-/+) for about two seconds until the frequency indication starts to change. Scanning stops when the unit tunes in a station. Or Press TUNE (-/+) repeatedly.
3. Adjust the volume by rotating VOLUME on the front panel or by pressing VOL (+/- ) on the remote control.
Presetting the Radio Stations
You can preset 50 stations for FM. Before tuning, make sure that you have turned down the volume.
1. Press INPUT/TUNER until the TUNER (FM) appears in the display window.
2. Select the desired frequency by using TUNE (-/+).
3. Press ENTER ( in the display window.
4. Press PRESET to select the preset number you want.
5. Press ENTER (
6. Repeat the steps 2 to 5 to store other
stations.
) a preset number will  ash
). The station is stored.
Deleting all the saved stations
Press and hold CLEAR for two seconds. “ERASE ALL” will  ash up. Press CLEAR again. Then all the saved stations are deleted.
Improving poor FM reception
Press D (blue) (ST/ MONO) coloured button on the remote control. This will change the tuner from stereo to mono and usually improve the reception.
See information about a radio station
The FM tuner is supplied with the RDS (Radio Data System) facility. This shows information about the radio station being listened to. Press RDS repeatedly to cycle through the various data types:
PS (Programme Service Name)
The name of the channel will appear in the display
PTY (Programme Type Recognition)
The programme type (e.g. Jazz or News) will appear in the display.
RT (Radio Text)
A text message contains special information from the broadcast station. This text may scroll across the display.
CT (Time controlled by the channel)
This shows the time and date as broadcast by the station.
4
Operation
Page 56
56
Operation
Playing content via your home network
This player can browse and play content from your PC and DLNA certi ed media servers connected on your home network.
About DLNA
This Player is a DLNA Certi ed digital media player that can display and play movie, photo and music content from your DLNA­compatible digital media server (PC and Consumer Electronics).
The Digital Living Network Alliance (DLNA) is a cross-industry organization of consumer
Operation
electronics, computing industry and mobile device companies. Digital Living provides consumers with easy sharing of digital media through a network in the home.
The DLNA certi cation logo makes it easy to  nd products that comply with the DLNA Interoperability Guidelines. This unit complies with DLNA Interoperability Guidelines v1.5.
When a PC running DLNA server software or other DLNA compatible device is connected to this player, some setting changes of software or other devices may be required. Please refer to the operating instructions for the software or device for more information.
Accessing a DLNA media server
1. Check the network connection and settings
(page 27).
2. Press
3. Select [Home Link] using U/u/I/i, and
press ENTER (
4. Select a DLNA media server from the list using U/u, and press ENTER ( ).
If you want to rescan for available media servers, press the green (B) coloured button.
Depending on the media server, this player may need to get permission from the server.
5. Select a  le using U/u/I/i, and press ENTER (
HOME MENU.
).
NOTE
) to play the  le.
Page 57
Operation
57
NOTE
• The  le requirements are described on page 11.
• You can use various playback functions. Refer to pages 38-44.
The  le requirements on page 11 are not always
compatible. There may be some restrictions due to the  le’s features and media server’s ability.
The thumbnail of the unplayable  les can be
displayed in the [Home Link] menu, but those cannot be played on this player.
If there is an unplayable music  le in the [Home
Link] menu, the player skips the  le and plays the next  le.
• The subtitle  le name and movie  le name have to be the same and located in the same folder.
• The playback and operating quality of the [Home Link] function may be a ected by your home network condition.
• The  les from removable media such as USB drive, DVD-drive etc. on your media server may not be shared properly.
Accessing a share folder from your PC
1. Start your PC that is connected on your
local area network.
2. On your PC, share folders which contain movie, photo or music  les.
3. On the player, check the network connection and settings (page 27).
4. Press
5. Select [Home Link] using U/u/I/i, and
press ENTER (
6. Select a share folder from the list using U/u, and press ENTER (
If you want to rescan available media servers, press the green (B) coloured button.
HOME MENU.
).
).
4
Operation
NOTE
Depending on the share folder, this player may need to input network user ID and password for accessing the folder.
7. Select a  le using U/u/I/i, and press ENTER ( ) to play the  le.
Page 58
58
Operation
NOTE
• The  le requirements are described on page 11.
• You can use various playback functions. Refer to pages 38-44.
• The thumbnail of the unplayable  les can be displayed in the [Home Link] menu, but those cannot be played on this player.
• If there is an unplayable music  le in the [Home Link] menu, the player skips the  le and play next  le.
• The subtitle  le name and movie  le name have to be the same and located at the same folder.
• The playback and operating quality of the [Home Link] function may be a ected by your home network condition.
• The  les on a removable media such as USB drive, DVD-drive etc. on your PC may not be shared properly.
• You may experience connection problems
Operation
depending on your PC’s environment.
PC requirements
• Windows® XP (Service Pack 2 or higher), Windows Vista® (no Service Pack required) Windows 7®
• 1.2 GHz Intel® Pentium® III or AMD Sempron™ 2200+ processors
• Network environment: 100 Mb Ethernet, WLAN (IEEE 802.11b/g/n)
NOTE
If you use Windows® XP or Windows Vista®, visit link below for more information on  le share settings.
Page 59
Operation
59
Entering a network user ID and the password
Depending on your PC’s environment, you may need to enter a network user ID and the password for accessing a shared folder.
1. The keyboard menu appears automatically if the network user ID and the password are required.
2. Use U/u/I/ press ENTER ( ) to con rm your selection on the keyboard menu.
To enter a letter with an accent mark, select the letter from the extended character set.
Example: Select “D” and then press DISPLAY ( ) to display the extended character set. Use ENTER ( ).
i
to select a character then
I/i
to select “D” or “Ď” and then press
3. When you  nish entering the network user ID and password, select [OK] using U/u/I/
i
and press ENTER (
The network user ID and password will be remembered after accessing the folder for your convenience. If you do not want the network user ID and password to be remembered, press red (A) coloured button to un-tick the [Remember] check box before accessing the folder.
) to access the folder.
4
Operation
[Clear] – Clear all entered characters. [Space] – Inserts a space at the cursor
position. [<–] – Deletes the previous character at the
cursor position. [ABC / abc / #+-=&] – Change the keyboard
menu settings to capital letters, small letters or symbols.
Page 60
60
Maintenance
5 Maintenance
Notes on Discs
Handling Discs
Never stick paper or tape on the disc.
Storing Discs
After playing, store the disc in its case. Do not expose the disc to direct sunlight or sources of heat and never leave it in a parked car exposed to direct sunlight.
Maintenance
Cleaning Discs
Do not use strong solvents such as alcohol, benzine, thinner, commercially available cleaners, or anti-static spray intended for older vinyl records.
Handling the Unit
When shipping the unit
Please save the original shipping carton and packing materials. If you need to ship the unit, for maximum protection, re-pack the unit as it was originally packed at the factory.
Keeping the exterior surfaces clean
• Do not use volatile liquids such as insecticide spray near the unit.
• Wiping with strong pressure may damage the surface.
• Do not leave rubber or plastic products in contact with the unit for a long period of time.
Cleaning the unit
To clean the player, use a soft, dry cloth. If the surfaces are extremely dirty, use a soft cloth lightly moistened with a mild detergent solution. Do not use strong solvents such as alcohol, benzine, or thinner, as these might damage the surface of the unit.
Maintaining the Unit
The unit is a high-tech, precision device. If the optical pick-up lens and disc drive parts are dirty or worn, the picture quality could be diminished. For details, please contact your nearest authorized service centre.
Page 61
6 Troubleshooting
General
Troubleshooting
61
The Power does not turn on.
The unit does not start playback.
The angle cannot be changed.
The subtitle language cannot be changed or turned o .
Cannot play MP3/WMA/ JPEG/DivX  les.
The remote control does not work properly.
• Plug the power cord into the wall outlet securely.
• Insert a playable disc. (Check the disc type, colour system, and regional code.)
• Place the disc with the playback side down.
• Place the disc on the disc tray correctly inside the guide.
• Clean the disc.
• Cancel the rating function or change the rating level.
• Multi-angles are not recorded on the DVD Video being played.
• Subtitles are not recorded on the DVD Video being played.
• The  les are not recorded in a format that the unit can play.
• The unit does not support the codec of the movie  le.
• The remote control is not pointed at the remote sensor of the unit.
• The remote control is too far from the unit.
• There is an obstacle in the path between the remote control and the unit.
• The battery in the remote control is exhausted.
6
Troubleshooting
Page 62
62
Troubleshooting
Picture
There is no picture. • Select the appropriate video input mode on the TV so the
picture from the unit appears on the TV screen.
• Connect the video connection securely.
• Check the [HDMI Color Setting] in the [Setup] menu is set to the appropriate item that conforms to your video connection.
• Your TV may not support the resolution you have set on the player. Change the resolution to one that your TV accepts.
• The player’s HDMI OUT jack is connected to a DVI device that does not support copyright protection.
Picture noise appears • You are playing a disc recorded in a colour system that is
di erent from your TV.
• Set the resolution to one that your TV accepts.
Sound
There is no sound or the sound is distorted.
Troubleshooting
• The unit is in scan, slow motion, or pause mode.
• The sound volume is low.
• Check the speaker cable connection. (page 16)
Page 63
Network
Troubleshooting
63
BD-LIVE feature does not work.
Design and speci cations are subject to change without notice.
• The connected USB storage may not have enough space. Connect the USB storage with at least 1GB free space.
• Ensure that the unit is correctly connected to the local area network and can access the internet (see page 27).
• Your broadband speed may not be fast enough to use the BD-LIVE features. Contact your Internet Service Provider (ISP) and increase the broadband speed to suit the unit’s.
• The [BD-LIVE connection] option in the [Setup] menu is set to [Prohibited]. Set the option to [Permitted].
Updates
Note that information on this product is available on the Pioneer website. Please check the website for information on updating or servicing your Blu-ray Disc PLAYER.
6
Troubleshooting
Page 64
64
Appendix
7 Appendix
Controlling a TV with the Supplied Remote Control
You can control your PIONEER TV using the buttons below.
TV Control Buttons
Appendix
Button Operation
1
(TV Power)
INPUT Switch the TV’s input source
CH +/- Scan up or down through
VOL +/- Adjust the volume of the
Turn the TV on or o .
between the TV and other input sources.
memorized channels.
TV.
Setting up the remote to control your TV
You can operate your TV with the supplied remote control. If your TV is listed in the table below, set the appropriate manufacturer code.
1. While holding down 1 (TV POWER) button, and press the manufacturer code for your TV with the numerical buttons (see the table below).
Manufacturer Code Number
Pioneer 1(Default) Sony 2, 3 Panasonic 4, 5 Samsung 6, 7 LG 8, 9
2. Release the 1 (TV POWER) button to complete setting.
Depending on your TV, some or all buttons may not function on the TV, even after entering the correct manufacturer code. When you replace the batteries of the remote, the code number you have set may be reset to
the default setting. Set the appropriate code number again.
NOTE
Depending on the unit being connected, you may not be able to control your TV using some of the buttons.
Page 65
Appendix
Area Code List
Choose an area code from this list.
Area Code Area Code Area Code Area Code
Afghanistan AF Argentina AR Australia AU Austria AT Belgium BE Bhutan BT Bolivia BO Brazil BR Cambodia KH Canada CA Chile CL China CN Colombia CO Congo CG Costa Rica CR Croatia HR Czech Republic CZ Denmark DK Ecuador EC Egypt EG El Salvador SV Ethiopia ET
Fiji FJ Finland FI France FR Germany DE Great Britain GB Greece GR Greenland GL Hong Kong HK Hungary HU India IN Indonesia ID Israel IL Italy IT Jamaica JM Japan JP Kenya KE Kuwait KW Libya LY Luxembourg LU Malaysia MY Maldives MV Mexico MX
Monaco MC Mongolia MN Morocco MA Nepal NP Netherlands NL Netherlands
Antilles AN New Zealand NZ Nigeria NG Norway NO Oman OM Pakistan PK Panama PA Paraguay PY Philippines PH Poland PL Portugal PT Romania RO Russian
Federation RU Saudi Arabia SA Senegal SN
Singapore SG Slovak Republic SK Slovenia SI South Africa ZA South Korea KR Spain ES Sri Lanka LK Sweden SE Switzerland CH Taiwan TW Thailand TH Turkey TR Uganda UG Ukraine UA United States US Uruguay UY Uzbekistan UZ Vietnam VN Zimbabwe ZW
65
Appendix
7
Page 66
66
Appendix
Language code List
Use this list to input your desired language for the following initial settings: [Disc Audio], [Disc Subtitle] and [Disc Menu].
Language Code Language Code Language Code Language Code
Afar 6565 Afrikaans 6570 Albanian 8381 Ameharic 6577 Arabic 6582 Armenian 7289 Assamese 6583 Aymara 6588 Azerbaijani 6590 Bashkir 6665 Basque 6985 Bengali; Bangla 6678 Bhutani 6890 Bihari 6672 Breton 6682
Appendix
Bulgarian 6671 Burmese 7789 Byelorussian 6669 Chinese 9072 Croatian 7282 Czech 6783 Danish 6865 Dutch 7876 English 6978 Esperanto 6979 Estonian 6984 Faroese 7079 Fiji 7074 Finnish 7073
French 7082 Frisian 7089 Galician 7176 Georgian 7565 German 6869 Greek 6976 Greenlandic 7576 Guarani 7178 Gujarati 7185 Hausa 7265 Hebrew 7387 Hindi 7273 Hungarian 7285 Icelandic 7383 Indonesian 7378 Interlingua 7365 Irish 7165 Italian 7384 Japanese 7465 Kannada 7578 Kashmiri 7583 Kazakh 7575 Kirghiz 7589 Korean 7579 Kurdish 7585 Laothian 7679 Latin 7665 Latvian, Lettish 7686 Lingala 7678
Lithuanian 7684 Macedonian 7775 Malagasy 7771 Malay 7783 Malayalam 7776 Maori 7773 Marathi 7782 Moldavian 7779 Mongolian 7778 Nauru 7865 Nepali 7869 Norwegian 7879 Oriya 7982 Panjabi 8065 Pashto, Pushto 8083 Persian 7065 Polish 8076 Portuguese 8084 Quechua 8185 Rhaeto-Romance
8277
Rumanian 8279 Russian 8285 Samoan 8377 Sanskrit 8365 Scots Gaelic 7168 Serbian 8382 Serbo-Croatian 8372 Shona 8378
Sindhi 8368 Singhalese 8373 Slovak 8375 Slovenian 8376 Spanish 6983 Sudanese 8385 Swahili 8387 Swedish 8386 Tagalog 8476 Tajik 8471 Tamil 8465 Telugu 8469 Thai 8472 Tonga 8479 Turkish 8482 Turkmen 8475 Twi 8487 Ukrainian 8575 Urdu 8582 Uzbek 8590 Vietnamese 8673 Volapük 8679 Welsh 6789 Wolof 8779 Xhosa 8872 Yiddish 7473 Yoruba 8979 Zulu 9085
Page 67
Video output resolution
When the non-copy protected media is playing back
Video Out
Resolution
576i (480i) 576p (480i) 576i (480i)
576p (480p) 576p (480p) 576p (480p)
720p 720p 720p 1080i 1080i 1080i
1080p / 24 Hz 1080p / 24 Hz 576i (480i) 1080i
1080p / 50 (60) Hz 1080p / 50 (60) Hz 576i (480i) 1080i
HDMI OUT
HDMI connected HDMI disconnected
When the copy protected media is playing back
Video Out
Resolution
576i (480i) 576p (480p) 576i (480i)
576p (480p) 576p (480p) 576p (480p)
720p 720p 576i (480i) 576p (480p) 1080i 1080i 576i (480i) 576p (480p)
1080p / 24 Hz 1080p / 24 Hz 576i (480i) 576p (480p)
1080p / 50 (60) Hz 1080p / 50 (60) Hz 576i (480i) 576p (480p)
HDMI OUT
HDMI connected HDMI disconnected
COMPONENT VIDEO OUT
COMPONENT VIDEO OUT
Appendix
67
HDMI OUT connection
• For the 576i (480i) resolution setting, real output resolution of HDMI OUT will change to 576p (480p).
• If you select a resolution manually and then connect the HDMI jack to TV and your TV does not accept it, the resolution setting is set to [Auto].
• If you select a resolution that your TV does not accept, the warning message will appear. After resolution change, if you cannot see the screen, please wait 20 seconds and the resolution will automatically revert back to the previous resolution.
• The 1080p video output frame rate may be automatically set to either 24 Hz or 50 Hz depending both on the capability and preference of the connected TV and based on the native video frame rate of the content on the BD-ROM disc.
COMPONENT VIDEO OUT connection
BD or DVD could prevent up-scaling on analogue output.
VIDEO OUT connection
The resolution of the VIDEO OUT jack is always outputted at 576i (480i) resolution.
Appendix
7
Page 68
68
Appendix
Trademarks and Licences
“Blu-ray Disc” and are trademarks.
“BD-LIVE” logo is a trademark of Blu-ray Disc Association.
“BONUSVIEW” is trademark of Blu-ray Disc Association.
HDMI, the HDMI Logo and High-De nition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing, LLC in the United States and other countries.
is a trademark of DVD Format/Logo Licensing
Corporation.
TM
Java and all Java-based trademarks and logos are trademarks or registered trademarks of Sun Microsystems, Inc. in the United States and other countries.
Appendix
Manufactured under licence from Dolby Laboratories. Dolby, and the double-D symbol are trademarks of Dolby Laboratories.
Manufactured under licence under U.S. Patent #’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535; 7,392,195; 7,272,567; 7,333,929; 7,212,872 & other U.S. and worldwide patents issued & pending. DTS and the Symbol are registered trademarks, & DTS-HD, DTS-HD Master Audio l Essential and the DTS logos are trademarks of DTS, Inc. Product includes software. © DTS, Inc. All Rights Reserved.
DLNA and DLNA CERTIFIED are trademarks and / or service marks of Digital Living Network Alliance.
DivX is a registered trademark of DivX, Inc., and is used under licence.
“x.v.Colour” or “x.v.Colour” is a trademark of Sony Corporation.
Page 69
Appendix
Windows Media is either a registered trademark or trademark of Microsoft Corporation in the United States and / or other countries.
69
“AVCHD” and the “AVCHD” logo are trademarks of Panasonic Corporation and Sony Corporation.
This product is licenced under the AVC patent portfolio licence and VC-1 patent portfolio licence for the personal and non-commercial use of a consumer to (i) encode video in compliance with the AVC Standard and VC-1 Standard (“AVC/ VC-1 Video”) and/or (ii) decode AVC/VC-1 Video that was encoded by a consumer engaged in a personal and non-commercial activity and/or was obtained from a video provider licenced to provide AVC/VC-1 Video. No licence is granted or shall be implied for any other use. Additional information may be obtained from MPEG LA, LLC. See http://www.mpegla.com.
iPod is a trademark of Apple Inc., registered in the U.S. and other countries.
iPhone is a trademark of Apple Inc. “Made for iPod” means that an electronic accessory
has been designed to connect speci cally to iPod and has been certi ed by the developer to meet Apple performance standards.
“Works with iPhone” means that an electronic accessory has been designed to connect speci cally to iPhone and has been certi ed by the developer to meet Apple performance standards.
Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.
This product includes technology owned by Microsoft Corporation and cannot be used or distributed without a license from Microsoft Licensing, Inc.
®
Bluetooth® wireless technology is a system which allows radio contact between electronic devices within a max. range of 10 meters. Connecting individual devices under Bluetooth wireless technology does not incur any charges. A mobile phone with Bluetooth wireless technology can be operated via the Cascade if the connection was made via Bluetooth wireless technology. The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Pioneer Corporation is under license. Other trademarks and trade names are those of their respective owners.
Appendix
7
Page 70
70
Appendix
Speci cations
General
• Power requirements: AC 220-240 V, 50/ 60 Hz
• Power consumption: 95 W In Standby mode: Less than 0.5W
• Dimensions (W x H x D): Approx. 430 × 64 × 304 mm
• Net Weight (Approx.):
3.6 kg
• Operating temperature: 41 °F to 95 °F (5 °C to 35 °C)
• Operating humidity: 5 % to 90 %
• Bus Power supply (USB): DC 5V
Inputs/ Outputs
• VIDEO OUT:
1.0 V (p-p), 75 Ω, sync negative, RCA jack x 1
• COMPONENT VIDEO OUT:
Appendix
(Y) 1.0 V (p-p), 75 Ω, sync negative, RCA jack x 1, (Pb)/(Pr) 0.7 V (p-p), 75 Ω, RCA jack x 2
• HDMI OUT (video/audio): 19 pin (HDMI standard, Type A, Version 1.3)
• Analogue AUDIO IN:
2.0 Vrms (1 kHz, 0 dB), 600 Ω, RCA jack (L, R) x 1
• DIGITAL IN (OPTICAL 1/2): 3 V (p-p), Optical jack x 2
• PORTABLE IN:
0.5 Vrms (3.5 mm stereo jack)
500 mA
Tuner
• FM Tuning Range:
87.5 to 108.0 MHz or 87.50 to 108.00 MHz
Ampli er
• Power output, (PEAK), (4Ω/3Ω) Total 560 W Front 180 W x 2 Sub-Woofer 200 W (Passive)
• Power output, (RMS),THD 10%(4Ω/3Ω) Total 480 W Front 150 W x 2 Sub-Woofer 180 W (Passive)
System
• Laser: Semiconductor laser Wavelength: 405 nm / 650 nm
• Signal system: Standard NTSC/PAL colour TV system
• Frequency response: 20 Hz to 20 kHz (48 kHz, 96 kHz, 192 kHz sampling)
• LAN port: Ethernet jack x 1, 10BASE-T/100BASE-TX
Speakers
• Front/Surround speaker (Left/ Right) Type: 2 Way Impedance Rated: 4 Ω Net Dimensions (W x H x D): Without speaker stand 77 x 395 x 55 mm With speaker stand 126 x 462 x 126 mm Net Weight: Without speaker stand 1.0 kg With speaker stand 1.3 kg
• Subwoofer Type: 1 Way 1 speaker Impedance Rated: 3 Ω Net Dimensions 130.5 x 420 x 375 mm (W x H x D): Net Weight: 4.4 kg
Page 71
Appendix
71
Open source software notice
The following GPL executables and LGPL libraries used in this product are subject to the GPL2.0/ LGPL2.1 License Agreements:
GPL EXECUTABLES: Linux kernel 2.6, bash, busybox, cramfs, dhcpcd, e2fsprogs, fdisk, mkdosfs, mtd-utils, net-tools, procps, samba-3.0.25b, sysutils, tcpdump, tftpd, tinylogin, unzip, utelnetd
LGPL LIBRARIES: uClibc, DirectFB, blow sh, cairo,  mpeg, iconv, libusb, mpg123
gSOAP Public License 1.3 LIBRARY: gsoap A copy of the corresponding source code can be
obtained by being charged the fee for distribution. To obtain a copy, contact your local Pioneer Customer Support .
You can obtain a copy of the GPL, LGPL licenses from http://www.gnu.org/licenses/old-licenses/ gpl-2.0.html and http://www.gnu.org/licenses/old­licenses/lgpl-2.1.html .
Also you can obtain a copy of gSOAP public license from http://www.cs.fsu.edu/~engelen/license.html.
This software is based in part on the work of the Independent JPEG Group copyright © 1991 - 1998, Thomas G. Lane.
This product includes
• boost C++: copyright © Beman Dawes 1999-2003
• c-ares : copyright © 1998 by the Massachusetts Institute of Technology
• curl: copyright © 1996 - 2008, Daniel Stenberg
• expat: copyright © 2006 expat maintainers
• freetype: copyright © 2003 The FreeType Project (www.freetype.org).
• jpeg: This software is based in part on the work of the Independent JPEG Group copyright © 1991 – 1998, Thomas G. Lane.
• mng: copyright © 2000-2007 Gerard Juyn, Glenn Randers-Pehrson
• ntp : copyright © David L. Mills 1992-2006
• OpenSSL: – cryptographic software written by Eric Young
(eay@cryptsoft.com).
– software written by Tim Hudson
(tjh@cryptsoft.com).
– software developed by the OpenSSL Project
for use in the OpenSSL Toolkit. (http://www.openssl.org)
• png: copyright © 2004 Glenn Randers-Pehrson
• portmap : copyright © 1990 The Regents of the University of California
• ptmalloc : copyright © 2001-2006 Wolfram Gloger
• UnitTest++ : copyright © 2006 Noel Llopis and Charles Nicholson
• UPnP SDK : copyright © 2000-2003 Intel Corporation
• strace : copyright © 1991, 1992 Paul Kranenburg copyright © 1993 Branko Lankester copyright © 1993 Ulrich Pegelow copyright © 1995, 1996 Michael Elizabeth Chastain copyright © 1993, 1994, 1995, 1996 Rick Sladkey copyright © 1999,2000 Wichert Akkerman
• xml2 : copyright © 1998-2003 Daniel Veillard
• XML-RPC For C/C++: copyright © 2001 by First Peer, Inc. All rights reserved. copyright © 2001 by Eric Kidd. All rights reserved.
• zlib: copyright © 1995-2002 Jean-loup Gailly and Mark Adler.
All rights reserved. Permission is hereby granted, free of charge, to
any person obtaining a copy of this software and associated documentation  les (the “Software”), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
Appendix
7
Page 72
2 Consignes de sécurité
1
Consignes de sécurité
Consignes de sécurité
ATTENTION
RISQUE D’ÉLECTROCUTION NE
PAS OUVRIR
ATTENTION: AFIN DE MINIMISER LES RISQUES
D’ÉLECTROCUTION, NE RETIREZ PAS LE COUVERCLE (OU L’ARRIÈRE) AUCUNE PIÈCE DE CET APPAREIL N’EST SUSCEPTIBLE D’ÊTRE RÉPARÉE PAR
L’UTILISATEUR CONFIEZ L’ENTRETIEN DE L’APPAREIL
À DES PERSONNES QUALIFIÉES.
Le symbole d’un éclair à l’intérieur d’un triangle sert à avertir l’utilisateur de la présence d’une tension dangereuse non isolée dans le corps de l’appareil, qui peut être su samment élevée pour provoquer un risque d’électrocution.
Le symbole d’un point d’exclamation à l’intérieur d’un triangle sert à avertir l’utilisateur de la présence d’instructions d’utilisation et de maintenance (entretien) importantes dans la documentation qui accompagne l’appareil.
Précautions et mises en garde
AVERTISSEMENT: POUR PRÉVENIR TOUT RISQUE D’INCENDIE OU D’ÉLECTROCUTION, N’EXPOSEZ PAS CET APPAREIL À LA PLUIE OU À L’HUMIDITÉ.
AVERTISSEMENT: n’installez pas cet appareil dans un espace con né tel qu’une bibliothèque ou tout autre meuble similaire.
ATTENTION: n’obstruez pas les ouvertures d’aération. Installez l’appareil conformément aux instructions du fabricant.
Les fentes et les ouvertures du boîtier servent à assurer la ventilation et le bon fonctionnement de l’appareil, ainsi qu’à le protéger contre la surchau e. Les ouvertures ne doivent jamais être bloquées en installant l’appareil sur un lit, un canapé, un tapis ou toute autre surface similaire. Cet appareil ne doit pas être placé dans un emplacement fermé tel qu’une bibliothèque ou une étagère, à moins d’assurer une ventilation adéquate ou que les instructions du fabricant l’autorisent.
ATTENTION: Ce produit est catégorisé comme un produit laser de classe 1 selon le règlement IEC 60825-1:2007 sur la sécurité des produits laser. A n de garantir l’utilisation correcte de cet appareil, veuillez lire attentivement ce manuel d’utilisation et conservez-le pour vous y référer ultérieurement. Si l’appareil nécessite une intervention de maintenance, contactez un point de service après­vente agréé.
L’utilisation de commandes, de réglages ou de procédures autres que ceux décrits dans ce document peut entraîner une exposition à des radiations dangereuses.
Pour éviter l’exposition directe au faisceau laser, n’essayez pas d’ouvrir le boîtier. Le rayonnement laser est visible lorsque l’appareil est ouvert. NE REGARDEZ PAS DIRECTEMENT LE FAISCEAU.
Page 73
3Consignes de sécurité
PRÉCAUTION concernant le cordon d’alimentation
Il est recommandé de brancher la plupart des appareils sur un circuit dédié.
Autrement dit, un circuit comportant une prise de courant qui alimente uniquement cet appareil et qui n’a ni autres prises ni circuit dérivé. Reportez­vous à la page des spéci cations de ce manuel d’utilisation pour plus de détails. Ne surchargez pas les prises murales. Les prises murales surchargées, desserrées ou endommagées, les câbles de rallonge, les cordons d’alimentation e lochés, ou les gaines isolantes craquelées ou endommagées constituent un danger. Chacune de ces conditions peut entraîner un risque de choc électrique ou d’incendie. Examinez régulièrement le cordon de votre appareil et, si son aspect indique qu’il est endommagé ou détérioré, débranchez-le, cessez d’utiliser l’appareil, et faites remplacer le cordon par une pièce de rechange appropriée auprès d’un point de service après-vente agréé. Protégez le cordon d’alimentation de sorte qu’il ne puisse pas être tordu, entortillé, pincé, coincé dans une porte ou piétiné. Faites particulièrement attention aux  ches, aux prises murales et au point d’où sort le cordon de l’appareil. Pour déconnecter l’appareil du réseau électrique, retirez le cordon d’alimentation de la prise électrique. Lors de l’installation de l’appareil, assurez-vous que la prise soit facilement accessible.
Cet appareil est équipé d’une batterie transportable ou de piles rechargeables.
Retrait sans danger de la batterie ou des piles de l’appareil: Pour retirer la batterie ou les piles
usagées, procédez dans l’ordre inverse de leur insertion. Pour empêcher toute contamination de l’environnement et tout danger pour la santé des êtres humains et des animaux, la batterie ou les piles usagées doivent être mises au rebut dans le conteneur approprié à un point de collecte prévu pour leur recyclage. Ne jetez pas la batterie ou les piles usagées avec les autres déchets. Recyclez toujours les batteries et piles rechargeables usagées. Les piles ne doivent pas être exposées à une chaleur excessive comme le soleil, ou le feu.
ATTENTION: l’appareil ne doit pas être exposé à des projections d’eau ou à des éclaboussures, et aucun objet rempli de liquide tel qu’un vase ne doit être posé sur l’appareil.
1
Consignes de sécurité
PIONEER déclare par la présente que
ce ou ces produits sont conformes
aux exigences essentielles et aux
dispositions applicables des directives
2004/108/CE, 2006/95/CE et 2009/125/
CE.
AVERTISSEMENT : pour éviter tout risque d’incendie,
ne posez pas sur l’appareil des sources de  amme nue (telle qu’une bougie allumée).
Page 74
4 Consignes de sécurité
Informations destinées aux utilisateurs sur la collecte et la mise au rebut des anciens équipements et piles usagées
Consignes de sécurité
Exemples de
Symbol examples
marquage
for batteries
pour les batteries
Les symboles qui  gurent sur les produits, emballage et/ou accompagnant des documents signi ent que les produits électriques et électroniques et les piles ne doivent pas être mélangés avec les ordures ménagères.
Pour un traitement, une récupération et un recyclage appropriés des produits anciens et piles usagées, portez-les vers les points de collecte prévus à cet e et conformément aux législations locales.
En mettant au rebut ces produits et piles correctement, vous aiderez à sauvegarder des ressources précieuses et à prévenir tout e et potentiellement négatif sur la santé humaine et sur l’environnement qui sinon devraient s’aggraver suite à une gestion inappropriée des déchets.
Pour plus d’informations sur la collecte et le recyclage des produits anciens et piles usagées, contactez votre administration locale, votre service de gestion des déchets ou les points de vente dans lesquels vous avez acheté ces articles.
Ces symboles ne sont valables qu’au sein de l’Union Européenne.
Pour les pays en dehors de l’Union Européenne :
Pour vous débarrasser de ces articles, contactez les autorités locales ou votre revendeur pour leur demander quelle méthode de mise au rebut semble la plus appropriée.
Remarques sur les droits d’auteur
• De même que le système CSS (Content Scramble System) protège le contenu des DVD, le système AACS (Advanced Access Content System) protège le contenu des disques Blu-ray ; les contenus ainsi protégés sont donc soumis à certaines restrictions en termes de lecture, de sortie de
Pb
signal analogique, etc. Le fonctionnement de cet appareil et les restrictions concernant son utilisation peuvent varier selon la date de votre achat, car ces restrictions peuvent être adoptées et/ou modi ées par la technologie AACS après la production de cet appareil.
• De plus, les technologies BD-ROM Mark et BD+ sont également utilisées en tant que systèmes de protection du contenu pour le format Blu­ray, ce qui implique certaines restrictions pour les contenus protégés par BD-ROM Mark et/ ou BD+, notamment en termes de lecture. Pour obtenir des informations complémentaires sur les technologies AACS, BD-ROM Mark et BD+ ou sur ce produit, contactez un service après-vente agréé.
• De nombreux DVD et BD-ROM sont encodés avec une protection contre la copie. En conséquence, vous devez raccorder votre lecteur directement à votre téléviseur, et non à un magné-toscope. Le raccordement à un magnétoscope génère en e et une image déformée pour les disques protégés contre la copie.
• Ce produit est doté d’une technologie de protection des droits d’auteur protégée par des brevets américains et d’autres droits sur la propriété intellectuelle. L’utilisation de cette technologie de protection des droits d’auteur doit faire l’objet d’une autorisation par Rovi et est exclusivement réservée à un usage domestique et à d’autres types de visionnage limités, sauf autorisation expresse de Rovi. Les opérations d’ingénierie inverse et de démontage sont interdites.
• Conformément aux lois sur les droits d’auteur en vigueur aux États-Unis et dans d’autres pays, l’enregistrement, l’utilisation, la di usion, la distrib­ution ou la révision sans autorisation d’émissions télévisées, de cassettes vidéo, de BD-ROM, de DVD, de CD et d’autres contenus peut engager votre responsabilité civile et/ou criminelle.
Page 75
Avis important concernant le système couleur du téléviseur
Le système couleur de ce lecteur di ère en fonction des disques lus.
Par exemple, lorsque le lecteur lit le disque enregistré dans le système couleur NTSC, l’image est di usée sous forme de signal NTSC.
Seuls les téléviseurs multisystème peuvent recevoir l’ensemble des signaux retransmis à partir du lecteur.
• Si vous avez un téléviseur PAL et que vous utilisez des disques ou des contenus vidéo enregistrés en NTSC, vous verrez des images déformées.
• Le téléviseur multisystème change le système couleur automatiquement en fonction des signaux d’entrée. Si le système couleur n’est pas modi é automatiquement, éteignez le téléviseur et rallumez-le pour voir des images normales à l’écran.
• Même si les disques enregistrés dans le système couleur NTSC s’a chent correctement sur votre téléviseur, il est possible que leur enregistrement pose problème dans votre enregistreur.
5Consignes de sécurité
1
Consignes de sécurité
Page 76
6
Table des matières
1
Consignes de sécurité
2 Précautions et mises en garde
2
Préparation
8 Introduction 8 À propos du symbole “ ” 8 Symboles utilisés dans ce
manuel 9 Accessoires fournis 10 Disques pouvant être lus 11 Compatibilité des  chiers 12 Code de région 12 AVCHD (codec vidéo avancé
en haute dé nition) 12 Con gurations systme
spéci ques 12 Remarques sur la
compatibilité 13 Télécommande 14 Panneau avant 15 Panneau arrire
3
Installation
16 Connexion au haut-parleur 16 Comment assembler les
socles d’enceinte et  xer vos haut-parleurs frontaux
18 Installation des haut-parleurs
sur le mur
19 Remarques supplémentaires
sur l’installation du haut-
parleur 19 Positionnement du système 20 Connexion à votre TV 20 Connexion HDMI 21 Connexion vidéo
composantes 22 Connexion vidéo 22 Réglage de la résolution 23 Connexion de l’antenne 23 Connexions avec un équipement
externe 23 Connexion AUX 24 Connexion PORT. IN
(Entrée Port)
24 Connexion OPTICAL IN 1/2
(Entrée optique) 25 Connexion Bluetooth® 27 Raccordement à votre réseau
domestique 28 Paramétrage réseau 30 Raccordement d’un périphérique
USB 31 Réglages 31 Réglage des paramètres 32 Menu [AFFICHAGE] 33 Menu [LANGUE] 34 Menu [AUDIO] 35 Menu [VERROU] 36 Menu [RÉSEAU]
Page 77
7
36 Menu [AUTRES] 37 E ets sonores
4
Utilisation
38 Lecture générale 40 Lecture avancée 42 A chage à l’écran 45 Utilisation des fonctions BD-LIVE 46 Lecture d’un  chier vidéo et d’un
disque VR 48 Lecture d’un  chier photo 50 Écoute de musique 53 Lecture de l’iPod 55 Utilisation de la fonction Radio 56 Lecture de contenu via votre réseau
domestique
5
Entretien
6
Dépannage
61 Général 62 Image 62 Son 63 Réseau
7
Annexe
64 Commande d’un téléviseur à l’aide
de la télécommande fournie 65 Liste des codes de région 66 Liste des codes de langue 67 Résolution de la sortie vidéo 68 Marques de commerce et licences 70 Caractéristiques 71 Avis concernant les logiciels open
source
1
2
3
4
5
60 Remarque sur les disques 60 Manipuler le lecteur
6
7
8
Page 78
8 Préparation
2 Préparation
Introduction
Préparation
À propos du symbole “ ”
Le symbole “ ” peut apparaître sur votre écran de téléviseur durant le fonctionnement. Il signi e que la fonction décrite dans ce manuel n’est pas disponible avec ce support spéci que.
Symboles utilisés dans ce manuel
REMARQUE
Indique des remarques et fonctionnalités spéciales.
ATTENTION
Indique des précautions à prendre pour éviter les dommages éventuels dus à une utilisation inappropriée.
Une section dont le titre comporte l’un des symboles suivants ne s’applique qu’aux disques représentés par ce symbole.
BD
DVD
AVCHD
ACD
MOVIE
MUSIC
PHOTO
Disque BD-ROM
DVD-Vidéo, DVD±R/RW en mode vidéo ou VR et  nalisé
DVD±R/RW au format AVCHD
CD audio
Fichiers vidéo
Fichiers musique
Fichiers image
Page 79
9Préparation
Accessoires fournis
Câble vidéo (1) Télécommande (1)
Piles (1) Antenne FM (1)
Sabot iPod (1)
Accessaries of speaker box (S-BD505FS)
Câbles du haut­parleur (3)
Tampons anti­dérapant - grands (1)
bases du socle d’enceinte (2)
vis (petits) (8)
vis (grands) (4)
joints (2)
2
Préparation
barres (2)
Page 80
10 Préparation
Disques pouvant être lus
Disques Blu-ray
- Disques tels que des  lms disponibles à l’achat ou à la location.
- Disques BD-R/RE contenant des  chiers vidéo, musicaux ou photo.
Préparation
DVD-VIDEO 8 / 12 cm Disques tels que des  lms disponibles à l’achat ou à la location.
DVD±R 8 / 12 cm
- Mode vidéo et  nalisé uniquement.
- Les disques double couche sont également acceptés.
- Format AVCHD  nalisé.
- Disques DVD±R contenant des  chiers vidéo, musicaux ou photo.
DVD-RW 8 / 12 cm
- Mode VR, mode vidéo et  nalisé uniquement.
- Format AVCHD  nalisé.
- Disques DVD-RW contenant des  chiers vidéo, musicaux ou photo.
DVD+RW 8 / 12 cm
- Mode vidéo et  nalisé uniquement.
- Format AVCHD.
- Format AVCHD  nalisé.
- Disques DVD+RW contenant des  chiers vidéo, musicaux ou photo.
Audio CD 8 / 12 cm
CD-R/RW 8 / 12 cm
- Disques CD-R/RW contenant des  chiers audio, vidéo, musicaux ou photo.
REMARQUE
• Selon les caractéristiques du matériel d’enregistrement ou du CD-R/RW (ou DVD±R/RW) à proprement parler, certains CD-R/RW (ou DVD±R/RW ) peuvent ne pas être lus par l’appareil.
• En fonction du logiciel d’enregistrement et de la  nalisation, il est possible que certains disques enregistrés (CD-R/RW, DVD±R/RW, BD-R/RE) ne puissent pas être lus.
• Il est possible que les BD-R/RE, DVD±R/RW et CD-R/RW enregistrés à l’aide d’un ordinateur ou d’un enregistreur de CD/DVD puissent ne pas être lus si le disque est endommagé ou sale, ou si la lentille du lecteur présente de la poussière ou de la condensation.
• Si vous enregistrez un disque à l’aide d’un ordinateur, même s’il est enregistré dans un format compatible, il existe une possibilité qu’il ne puisse pas être lu à cause des paramètres du logiciel d’application utilisé pour créer le disque. (Adressez-vous à l’éditeur du logiciel pour des informations plus détaillées.)
• Pour obtenir une qualité de lecture optimale, ce lecteur nécessite que les disques et les enregistrements répondent à certaines normes techniques.
• Les DVD préenregistrés sont automatiquement conformes à ces normes. Il existe de nombreux types de formats de disques enregistrables (dont des disques CD-R contenant des  chiers MP3 ou WMA), et ces formats requièrent certaines conditions préexistantes pour que la lecture soit possible.
• Veuillez noter qu’il est nécessaire d’avoir une autorisation pour télécharger des  chiers MP3 ou WMA et de la musique depuis internet. Notre société n’ayant pas le droit d’accorder une telle autorisation, cette dernière doit toujours être recherchée auprès du détenteur des droits d’auteur.
Page 81
11Préparation
Compatibilité des  chiers
Généralités
Extension de  chiers disponibles :
“.jpg”, “.jpeg”, “.png”, “.avi”, “.divx ”, “.mpg”, “.mpeg”, “.mkv”, “.mp4”, “.mp3”, “.wma”, “.wav”
Les extensions de  chiers disponibles varient suivant les serveurs DLNA.
• Certains  chiers “.wav” ne sont pas pris en charge par cet appareil.
• Les noms des  chiers sont limités à 180 caractères.
• Suivant la taille et le nombre de  chiers, plusieurs minutes peuvent être nécessaires pour lire les contenus du support.
Nombre maximal de  chiers par dossier:
2 000 (nombre total de  chiers et de dossiers)
Format des CD-R/RW, DVD±R/RW et BD-R/ RE: ISO 9 660+JOLIET, UDF et UDF Bridge
FILM
Taille de résolution disponible:
1 920 x 1 080 pixels (L x H) Sous-titres compatibles: SubRip (.srt /
.txt), SAMI (.smi), SubStation Alpha (.ssa/.txt), MicroDVD (.sub/.txt), VobSub (.sub), SubViewer
1.0 (.sub), SubViewer 2.0 (.sub/.txt), TMPlayer
(.txt), DVD Subtitle System (.txt)
• Le  ltre VobSub (.sub) n’est pas disponible avec la fonction [Home Link].
Formats codec compatibles: “DIVX3.xx”, “DIVX4.xx”, “DIVX5.xx”, “XVID”, “DIVX6.xx ” (lecture standard uniquement), H.264/MPEG-4 AVC, MPEG1 SS, MPEG2 PS, MPEG2 TS Formats audio compatibles: “Dolby Digital”,
“DTS”, “MP3”, “WMA”, “AAC”, “AC3”
• Ce lecteur n’est pas entièrement compatible avec le format audio WMA et AAC.
Fréquence d’échantillonnage: dans la plage 32 kHz à 48 kHz (WMA), dans la plage 16 kHz à 48 kHz (MP3), Débit binaire: dans la plage 20 kbps à 320 kbps (WMA), dans la plage 32 kbps à 320 kbps (MP3)
REMARQUE
• Les  chiers vidéo haute dé nition contenus sur un CD ou un périphérique USB 1,0/1,1 risquent de ne pas être lus correctement. Pour lire des  chiers vidéo haute dé nition, il est recommandé d’utiliser les formats BD, DVD ou USB 2,0.
• Ce lecteur prend en charge le format H.264/ MPEG-4 AVC pro l Main ou High au niveau 4,1. Dans le cas d’un  chier de niveau supérieur, un message d’avertissement s’a chera à l’écran.n.
• Ce lecteur ne prend pas en charge les  chiers enregistrés avec fonction GMC*1 ou Qpel*2. Il s’agit de techniques d’encodage vidéo du standard MPEG4, comme celles dont disposent DivX ou XVID.
*1 GMC – Global Motion Compensation
(compensation globale de mouvements)
*2 Qpel – Quarter pixel (quart de pixel)
MUSIQUE
Fréquence d’échantillonnage: dans la plage 8 kHz à 48 KHz (WMA), dans la plage 11 kHz à 48 kHz (MP3) Débit binaire: dans la plage 8 kbps à 320 kbps (WMA, MP3),
REMARQUE
• Ce lecteur ne prend pas en charge les balises ID3 intégrées dans les  chiers MP3.
• La durée totale de lecture indiquée à l’écran peut ne pas être correcte pour les  chiers VBR.
PHOTO
Taille recommandée:
Inférieure à 4 000 x 3 000 x 24 bits/pixel Inférieure à 3 000 x 3 000 x 32 bits/pixel Inférieure à 4 MByte/ le
• Les  chiers d’image photo progressifs et à compression sans perte ne sont pas pris en charge.
2
Préparation
Page 82
12 Préparation
Code de région
Un code de région est indiqué à l’arrière de l’appareil. Ce dernier ne peut lire que les disques DVD ou BD-ROM de la même zone ou portant la mention “ALL” (Toutes zones).
AVCHD (codec vidéo avancé en haute dé nition)
Préparation
• Ce lecteur peut lire les disques au format AVCHD. Ces disques sont normalement enregistrés et utilisés dans les caméscopes.
• Le format AVCHD est un format d’enregistrement numérique de vidéo haute dé nition.
• Le format MPEG-4 AVC/H.264 peut compresser les images avec une plus grande e cacité que le format de compression d’image conventionnel.
• Certains disques AVCHD utilisent le format “x.v.Colour”.
• Ce lecteur peut lire les disques AVCHD au format “x.v.Colour”.
• Selon leurs conditions d’enregistrement, il est possible que certains disques au format AVCHD ne puissent pas être lus.
• Les disques au format AVCHD doivent être  nalisés.
• Le format “x.v.Colour” o re une palette de couleurs plus vaste que les disques pour caméscope DVD normaux.
Con gurations systme spéci ques
Pour la lecture vidéo haute dé nition:
• Téléviseur haute dé nition doté de prises d’entrée COMPOSANTES ou HDMI.
• BD-ROM avec du contenu haute dé nition.
• Une entrée HDMI ou DVI compatible HDCP est nécessaire sur votre téléviseur pour certains contenus (indiqués par les auteurs du disque).
• Pour l’extrapolation des DVD de dé nition standard, une entrée HDMI ou DVI compatible HDCP est nécessaire sur votre téléviseur a n d’accéder aux contenus protégés contre la copie.
Remarques sur la compatibilité
• Comme les disques BD-ROM sont un nouveau format, certains problèmes avec les disques, la connexion numérique ou d’autres problèmes de compatibilité sont possibles. Si vous rencontrez des problèmes de compatibilité, contactez un point de service après-vente agréé.
• Pour visionner un contenu haute dé nition et extrapoler un contenu DVD de dé nition standard, il peut être nécessaire d’avoir une entrée HDMI ou une entrée DVI compatible HDCP sur votre téléviseur.
• Certains DVD et BD-ROM peuvent limiter l’utilisation de certaines fonctionnalités ou commandes.
• Vous pouvez utiliser un périphérique USB qui sert à stocker des informations liées au disque, notamment les contenus en ligne téléchargés. Le disque que vous utilisez déterminera la durée de conservation de ces informations.
Page 83
Télécommande
1
2
3
13Préparation
• • • • • • • • • a • • • • • • • • •
(STANDBY/ON): permet
1
d’allumer ou d’éteindre le lecteur.
OPEN/CLOSE: permet
Z
d’ouvrir ou de fermer le plateau du disque.
INPUT/TUNER: permet de
modi er la source d’entrée. BT AUDIO: Change le mode
d’entrée pour BT AUDIO directement.
OPTICAL: Passe automatiquement en mode d’entrée optique.
DISPLAY: permet d’activer ou de désactiver l’a chage à l’écran.
HOME MENU: permet d’a cher ou de quitter le [Menu d’accueil].
MENU: permet d’accéder au menu du disque.
Touches  échées: permettent de sélectionner une option dans le menu.
ENTER: permet de con rmer la
Insertion des piles
Retirez le couvercle des piles au dos de la télécommande, et insérez une pile R03 (taille AAA), en respectant les polarités et .
sélection du menu. TUNE (+/-): Réglage de la station
de radio de votre choix. PRESET: Sélections programmées
des radios.
• • • • • • • • • b • • • • • • • • •
RETURN: permet de quitter le
O
menu ou de reprendre la lecture. POPUP/ TOP MENU: permet
d’a cher le menu de titres du DVD ou le menu contextuel du BD­ROM, s’il est disponible.
STOP: permet d’arrêter la
x
lecture.
PLAY: permet de démarrer la
B
lecture.
PAUSE/STEP: permet de mettre
X
la lecture en pause.
./>
à la piste, au  chier ou au chapitre précédent/suivant.
SKIP: Permet de passer
m/M
d’e ectuer une recherche vers l’arrière ou l’avant.
SPK LEVEL: Règle le volume sonore du haut-parleur souhaité.
z
audio.
MUTE: Passer en mode muet. SOUND: Sélectionne un mode
d’e et sonore. VOL +/- : Ajustez le volume des
haut-parleurs.
• • • • • • • • • c • • • • • • • • •
Touches numériques 0-9: permettent de sélectionner les options numérotées dans un menu.
MARKER: Marque n’importe quel passage lors de la lecture.
SEARCH: A che ou ferme le menu de recherche.
section de votre choix. CLEAR: permet d’e acer un index
dans le menu de recherche ou un numéro lors de la dé nition du mot de passe.
DIMMER: Pour réduire la luminosité de l’a chage de l’appareil.
ZOOM: Accède au menu du zoom. Touches de couleurs
(A, B, C, D): Utilisées pour naviguer
sur les menus.
- Bouton A (RDS): permet
- Bouton B (PTY): visualise le type
- Bouton C (PTY SEARCH):
- Bouton D: Sélectionne mono/
Touches de contrôle TV: Voir page
64. SLEEP: Fixe un certain laps de
temps après lequel l’appareil s’éteint.
SCAN: permet
USB REC: enregistre un CD
REPEAT: permet de répéter une
d’activer la fonction RDS (Radio Data System).
de programme du RDS.
Recherche un type de programme.
stéréo en mode FM.
2
Préparation
Page 84
14 Préparation
Panneau avant
Préparation
a
b
1
Plateau de disque
Touches de fonctionnement
1
STANDBY/ON Touche
Z
(OPEN/CLOSE)
FONCTION
Change la source d’entrée ou la fonction.
B/X
(PLAY / PAUSE)
x
(STOP)
./>
(SKIP)
- TUNE + (Réglage de station de radio)
3 4 5 6 7
Capteur de la télécommande
c
Fenêtre d’a chage
d
PORTABLE IN
e
Port USB
f
Réglage du volume
g
2
Page 85
Panneau arrire
1 2 3 4 5
15Préparation
2
Préparation
6 7 8 9 10 11
Cordon d’alimentation
a
Branchez sur le secteur.
Connecteurs haut-parleurs
b
Ventilateur
c
Connecteur Antenne
d
VIDEO OUT
e
AUX (L/R) INPUT
f
COMPONENT VIDEO (Y PB PR)
g
OUTPUT (PROGRESSIVE SCAN)
OPTICAL IN 1(TV) / 2
h
iPod (24 broches)
i
Raccordement au sabot iPod fourni.
HDMI OUT (type A, version 1.3)
j
Entrées HDMI pour connexion TV.
Port LAN
k
Page 86
16 Installation
3 Installation
Connexion au haut-parleur
Pour le caisson de basse :
Utilisez les adhésifs fournis pour  xer 4 tapis
Installation
antidérapants à la base du subwoofer.
Tampons anti-dérapant - grands
large non-skid pads
Comment assembler les socles d’enceinte et  xer vos haut­parleurs frontaux
1. Glissez la barre de dessous les trous
derrière la base et  xez-la avec les 4 vis.
2. Fixez les joints à la barre.
Fixez les joints sur la surface de la barre où vous allez monter le haut-parleur.
Page 87
17Installation
3. Glissez la corde du haut-parleur de dessous le trou derrière la base jusqu’à la barre et connectez-la à la borne du haut-parleur. Après la connexion, mettez le  l du haut-parleur dans le trou qui se trouve au dos du haut-parleur.
Raccordez le tube coloré sur le  l à
l’indicateur de couleur sur lÅfetiquette, puis glissez le  l blanc avec la ligne grise au côté rouge (+) et l’autre  l au côté noir (-).
4. Fixez le haut-parleur et la barre avec 2 vis.
Assurez-vous que le  l du haut-parleur n’est pas coincé entre le haut-parleur et la barre.
5. Après la connexion, mettez le  l du haut-parleur au dos de la base du socle d’enceinte.
6. Connectez les  ls au lecteur.
Connectez le blanc avec le  l gris dans
le côté (+) et l’autre  l électrique dans le côté (-). Pour connecter le câble au lecteur, appuyez sur chaque doigtier plastique et ouvrez la connexion à la borne. Glissez le  l et lâchez le doigtier.
Red (+)
Rouge (+)
Blanc (+)
Orange (+)
Black (–)
Noir (–)
White (+)
ATTENTION
3
Installation
• Ne branchez pas d’autres haut-parleurs que ceux fournis avec de système.
• Ne branchez pas les haut-parleurs fournis sur aucun autre ampli cateur que celui fourni avec ce système. Toute connexion sur un autre ampli cateur peut se traduire par un dysfonctionnement ou un incendie.
Page 88
18 Installation
Installation des haut-parleurs sur le mur
Avant le montage
Il est à noter que le système du haut-parleur est lourd et que son poids peut faire se desserrer les vis ou rendre impossible le soutien au système par les materiaux de mur, ce qui pourrait provoquer l’e ondrement du haut-parleur. Faites en sorte que le mur sur lequel vous voulez monter les haut-parleurs est su samment solide pour les supporter. Ne les posez pas sur les murs en contre-plaqué ou à
Installation
surface meuble.
Les vis de montage ne sont pas fournis. Utilisez les vis appropriés aux matériaux de mur qui peuvent supporter le poids du haut-parleur.
ATTENTION
• Si vous n’êtes pas sûr de la qualité et de la puissance du mur, veuillez demander conseil à un spécialiste.
• Pioneer ne porte pas la responsabilité des accidents ou des dommages causés par les fautes d’installation.damage that result from improper installation.
Comment  xer les haut-parleurs
Le haut-parleur frontal peut être suspendu sur le mur d’une manière verticale ou horizontale. Veuillez utiliser un trou pour l’accrocher verticalement et en utiliser deux pour le pendre horizontalement. L’illustration ci­dessous montre le haut-parleur avant droite.
}GG
Dressage vertical
o
Trou
Dressage horizontal
o¡GG
o
Trou
Quand vous installez le haut-parleur de façon horizontale, dressez-le en faisant en sorte que la borne du haut-parleur située sur son dos est à l’extérieur, au bout de la surface, et le plus loin de l’autre haut-parleur.
Borne du haut-parleur
Avant droite
Borne du haut-parleur
Avant gauche
GzGz
GmGm
Vis de montage
Mounting Screw
(non fourni)
(Not supplied)
\GGG^G
De 5 mm à 7 mm
\G
XWG

REMARQUE
Ne raccordez pas les enceintes fournis à un ampli cateur autre que celui qui est fourni avec ce système. Une telle connexion pourrait provoquer une défaillance, voire un incendie.

Page 89
Remarques supplémentaires
A
B
C
A
A
D
sur l’installation du haut­parleur
Installez les haut-parleurs avant-gauche et avant-droite à une distance égale du téléviseur.
Précautions:
Assurez-vous que tous les  ls nus du haut­parleur sont torsadés et complètement insérés dans la borne du haut-parleur. Au cas où le  l du hautparleur touche le panneau derrière, la coupure d’électricité peut survenir comme mesure de sécurité.
Les haut-parleurs frontaux équippés de ce système sont protégés contre le magnétisme. Cependant, selon l’emplacement de l’installation, une distorsion des couleurs peut se produire si vous installez le haut-parleur trop près de l’écran du téléviseur. Si c’est le cas, veuillez éteindre le téléviseur, et l’allumer dans 15-30 minutes. Au cas où le problème persiste, éloignez le système du téléviseur.
Le subwoofer n’est pas protégé contre le magnétisme et ne doit donc pas être placé près d’un téléviseur ou d’un moniteur. En plus, les supports magnétiques de données (tels que disquettes, bandes et cassettes vidéo) ne doivent pas être mis à proximité du subwoofer.
Ne  xez pas le subwoofer sur le mur ou sur le plafond. Ils peuvent s’e ondrer et provoquer des blessures humaines.
Positionnement du système
L’illustration suivante montre comment positionner le système (exemple). Notez que les illustrations de ces instructions sont à titre explicatives et peuvent parfois di érer de votre Home Cinema. Pour un meilleur son surround possible, tous les haut-parleurs autres que le subwoofer doivent être placés à égale distance de la position d’écoute (A).
Haut-parleur avant gauche (L)/
A
Haut-parleur avant droit (R):
B
Placez les haut-parleurs avant sur les côtés de l’écran ou du moniteur et si possible à la même hauteur.
Subwoofer:
C
La position du subwoofer n’est pas cruciale car les extrêmes graves sont non-directionnels. Mais il est préférable de placer le subwoofer près des haut-parleurs avant. Tournez-le légèrement vers le centre de la pièce pour réduire les ré exions sur les murs.
Lecteur
D
ATTENTION
• Veillez à ce que les enfants ne mettent pas les mains ou tout autre objet dans le canal du haut­parleur. *Canal du haut parleur pour l’excitation aéro­acoustique : basses abondantes sur un haut­parleur acoustique.
• Les enceintes contenant des pièces magnétiques, il est possible que des irrégularités de couleurs apparaissent sur l’écran du téléviseur ou du moniteur d’ordinateur. Utilisez les enceintes à une distance éloignée de votre téléviseur ou écran d’ordinateur.
19Installation
3
Installation
Page 90
20 Installation
Connexion à votre TV
E ectuez la ou les connexions suivantes en fonction des capacités de vos appareils à connecter à l’ampli.
• Connexion HDMI (voir pages 20-21)
• Connexion vidéo composantes (page 21)
• Connexion vidéo (page 22)
REMARQUE
Installation
• Il existe plusieurs façons de connecter le lecteur en fonction de votre TV et des autres appareils que vous souhaitez connecter. Choisissez l’une des connexions présentées dans le manuel.
• Veuillez vous référez aux manuels de votre TV, chaîne hi- ou autres dispositifs nécessaires pour e ectuer les connexions correctement.
• Assurez-vous que le lecteur est branché directement à votre TV. Réglez la TV sur le canal d’entrée vidéo.
• Ne branchez pas votre lecteur via votre magnétoscope. L’image pourrait être déformée par le système de protection contre la copie.
Connexion HDMI
Si vous possédez un moniteur ou un téléviseur HDMI, vous pouvez le raccorder à ce lecteur à l’aide d’un câble HDMI (type A, version 1.3). Raccordez la prise de sortie HDMI OUT de l’appareil à la prise d’entrée HDMI IN d’un téléviseur ou d’un moniteur compatible HDMI.
Connexion HDMI
Lecteur
Player
TV
TV
Réglez la source du téléviseur sur HDMI (reportez-vous au manuel d’utilisation de votre téléviseur).
Page 91
21Installation
REMARQUE
• Une modi cation de la résolution alors que la connexion est déjà établie peut entraîner des dysfonctionnements. Pour résoudre le problème, éteignez le lecteur puis rallumez-le.
• Lorsque la connexion HDMI avec HDCP n’est pas véri ée, le téléviseur a che un écran noir. Dans ce cas, véri ez la connexion HDMI ou débranchez le câble HDMI.
• Si des interférences apparaissent à l’écran, véri ez le câble HDMI (la longueur du câble ne doit généralement pas dépasser 4,5 m et vous devez utiliser un câble HDMI haut-débit (version 1.3).
• Si un périphérique HDMI raccordé n’accepte pas la sortie audio du lecteur, le son du périphérique HDMI peut être déformé ou muet.
• Lorsque vous utilisez la connexion HDMI, vous pouvez modi er la résolution pour la sortie HDMI. (Reportez-vous à la section “Réglage de la résolution”, page 22.)
• Sélectionnez le type de sortie vidéo pour la prise de sortie HDMI OUT à l’aide de l’option [Rég. couleur HDMI] dans le menu [Con g.] (voir page 33).
• Lorsque vous raccordez un appareil compatible HDMI ou DVI, e ectuez les véri cations suivantes:
- Essayez d’éteindre l’appareil HDMI/DVI ainsi
que ce lecteur. Ensuite, allumez l’appareil HDMI/DVI, attendez environ 30 secondes, puis allumez ce lecteur.
- L’entrée vidéo de l’appareil raccordé est
correctement réglée pour cet appareil.
- L’appareil raccordé est compatible avec les
résolutions d’entrée vidéo 720 x 576p (480p), 1280 x 720p, 1920 x 1080i et 1920 x 1080p.
• Certains appareils DVI ou HDMI compatibles HDCP ne fonctionneront pas avec ce lecteur.
- L’image ne s’a chera pas correctement avec
un appareil non HDCP.
- Ce lecteur ne peut pas e ectuer la lecture et le
téléviseur a che un écran noir.
Connexion vidéo composantes
Raccordez les prises COMPONENT VIDEO OUT de l’appareil avec les prises correspondantes du téléviseur, à l’aide de câbles Y Pb Pr. Vous pouvez entendre le son sortir des enceintes du système.
Connexion en composantes
Player
Lecteur
PR
VIDEO
L
PB
AUX
R
Y
COMPONENT
VIDEO
INPUT
OUTPUT
Vert
Green Blue
Bleu
Red
Rouge
TV
TV
REMARQUE
Lorsque vous utilisez la sortie vidéo composantes COMPONENT VIDEO OUT, vous pouvez modi er la résolution pour la sortie. (Reportez-vous à la section “Réglage de la résolution”, voir page 22.)
3
Installation
Page 92
22 Installation
Connexion vidéo
Raccordez la prise de sortie vidéo VIDEO OUT du lecteur à la prise d’entrée vidéo du téléviseur à l’aide d’un câble vidéo. Vous pouvez entendre le son sortir des enceintes du système.
Connexion vidéo
Lecteur
Installation
TV
TV
Yellow
Jaune
PR
VIDEO
L
PB
AUX
R
Y
COMPONENT
VIDEO
INPUT
OUTPUT
Réglage de la résolution
Le lecteur o re plusieurs résolutions de sortie pour les prises de sortie HDMI OUT et COMPONENT VIDEO OUT. Vous pouvez modi er la résolution à l’aide du menu [Con g.].
1. Appuyez sur la touche HOME MENU (
2. Utilisez les touches I/
sélectionner [Con g.], puis appuyez sur ENTER (
). Le menu [Con g.] apparaît.
3. Utilisez les touches U/u pour sélectionner l’option [AFFICHAGE], puis appuyez sur i pour accéder au deuxième niveau.
4. Utilisez les touches U/u pour sélectionner l’option [Résolution] puis appuyez sur ENTER (
) ou i pour accéder au troisième
niveau de menu.
i/U/u
pour
).
5. Utilisez les touches U/u pour sélectionner la résolution souhaitée, puis appuyez sur la touche ENTER ( ) pour con rmer votre choix.
REMARQUE
• Si votre téléviseur n’accepte pas la résolution que vous avez dé nie sur le lecteur, vous pouvez régler la résolution sur 576p (480p) comme suit:
1. Appuyez sur Z pour ouvrir le tiroir à disque.
2. Appuyez sur la touche x pendant au moins
5 secondes.
• Comme plusieurs facteurs a ectent la résolution de sortie vidéo, reportez-vous à la section “Résolution de la sortie vidéo”, page 67.
Page 93
23Installation
Connexion de l’antenne
Branchez l’antenne fournie pour écouter la radio.
Connexion de l’antenne
Lecteur
Player
Connexions avec un équipement externe
Connexion AUX
Vous pouvez écouter la musique de votre appareil avec les prises de sortie analogique audio des haut-parleurs du système.
Branchez le câble de sortie analogique audio de votre appareil aux entrées L/R (INPUT) de l’ampli. Puis sélectionnez l’option AUX en appuyant sur les touches INPUT/TUNER, I/i et ENTER (
Connexion AUX
Lecteur
Player
).
PR
VIDEO
L
PB
AUX
R
Y
COMPONENT
VIDEO
INPUT
3
Installation
REMARQUE
Après avoir connecté l’antenne  laire FM, positionnez-la à l’horizontal autant que possible. Veillez à étendre complètement l’antenne  laire FM.
Rouge
Red
Blanc
White
To the audio output jacks
Vers la sortie audio de
of your component
votre appareil
(TV, VCR, etc.)
(TV, VCR, etc.)
Page 94
24 Installation
Connexion PORT. IN (Entrée Port)
Vous pouvez écouter la musique de votre lecteur audio portable sur les haut-parleurs du système.
Branchez le casque (ou la sortie de ligne) de votre lecteur audio portable au PORTABLE IN de l’ampli. Puis sélectionnez l’option [PORTABLE] en appuyant sur les touches INPUT/TUNER, I/i et ENTER (
Connexion PORT.IN
Installation
Connexion OPTICAL IN 1/2 (Entrée optique)
Vous pouvez écouter la musique de votre appareil avec la connexion numérique optique depuis les haut-parleurs du système.
Connectez la prise de sortie optique de votre appareil dans la prise OPTICAL IN 1/2 de l’ampli. Puis sélectionnez l’option [OPTICAL 1/2] en appuyant sur les touches INPUT/TUNER,
).
I/i
et ENTER (
sur OPTICAL.
Connexion optique
). Ou appuyez directement
Vers la prise de sortie
To the digital
numérique optique
optical output jack
de votre appareil
of your component
Lecteur MP3, etc.
twZGSGUUU
Page 95
25Installation
Connexion Bluetooth®
À propos de Bluetooth
Bluetooth® est une technologie de communication sans  l dédiée à des connexions à courte distance.
La portée accessible est inférieure à 10 mètres. (Le son peut être interrompu si la connexion interfère avec d’autres ondes électroniques ou si vous connectez votre dispositif bluetooth dans d’autres pièces.) La connexion de périphériques individuels en employant la technologie sans  l Bluetooth n’entraîne aucune charge supplémentaire. Vous pouvez faire fonctionner un téléphone mobile équipé de la technologie sans  l Bluetooth via la Cascade si la connexion a été réalisée au moyen de la technologie sans  l Bluetooth.
Équipements pris en charge : téléphone mobile, MP3, ordinateur portable, assistant numérique personnel (PDA) (ces appareils acceptent les écouteurs stéréo).
Pro ls Bluetooth
Pour utiliser la technologie sans  l, les appareils doivent être capables d’interpréter certain pro ls. Cet appareil est compatible avec le pro l suivant.
A2DP (Advanced Audio Distribution Pro le ­pro l de distribution audio avancée)
1. Sélectionnez la fonction Bluetooth à l’aide de la touche INPUT/TUNER ou BT AUDIO. “BT AUDIO”, puis “BT READY” apparaissent sur la fenêtre d’a chage.
2. Faites fonctionner l’équipement Bluetooth et exécutez la procédure d’appariement. En e ectuant la recherche de cet appareil avec l’équipement Bluetooth, selon le type d’équipement Bluetooth, la liste des équipements trouvés peut apparaître sur l’a chage de l’équipement Bluetooth . Votre appareil apparaît sous l’appellation “PIONEER AUDIO”.
3. Entrez le code PIN. Code PIN : 0000
4. Lorsque cet appareil est correctement apparié avec votre équipement Bluetooth, la LED Bluetooth de cet appareil s’allume et “BT SINK” apparaît.
REMARQUE
Selon le type de votre équipement Bluetooth, certains appareils peuvent avoir des méthodes d’appariement di érentes.
5. Écoute de morceaux de musique. Pour écouter de la musique enregistrée sur votre équipement Bluetooth, reportez-vous au mode d’emploi de votre équipement Bluetooth.
3
Installation
Écoute de morceaux de musique d’un équipement Bluetooth
Appariement de votre appareil avec l’équipement Bluetooth
Avant de démarrer la procédure d’appariement, véri ez que la fonction Bluetooth est activée sur votre équipement Bluetooth. Pour plus d’informations, reportez-vous au mode d’emploi de votre équipement Bluetooth. Une fois l’appariement réalisé, il ne sera plus nécessaire de l’e ectuer à l’avenir.
REMARQUE
• Si vous changez le fonctionnement de l’appareil, la fonction Bluetooth est déconnectée, vous devez alors refaire l’appariement.
• AVRCP n’est pas accessible dans ce mode.
Page 96
26 Installation
Véri cation des informations de l’équipement Bluetooth connecté
Cette fonction est disponible après l’appariement. Vous pouvez contrôler les informations Bluetooth.
Appuyez sur DISPLAY en maintenant la touche enfoncée plusieurs fois.
Les informations Bluetooth sont modi ées comme suit. Adresse de l’équipement Bluetooth local Nom de l’équipement t Aucun t ...
Installation
t
REMARQUE
• Cet appareil ne reconnaît pas le pro l écouteur
mono (pro l mains libres).
• Le son peut être interrompu si la connexion
interfère avec d’autres ondes électroniques.
• Vous ne pouvez pas commander l’équipement
Bluetooth avec cet appareil.
• L’appariement est limité à un équipement
Bluetooth pour un appareil et le multi appariement n’est pas possible.
• Bien que la distance entre votre équipement
Bluetooth et l’appareil soit inférieure à 10 m, s’il y a des obstacles entre ces éléments, votre équipement Bluetooth peut ne pas être connecté.
• Selon le type d’équipement, vous pourriez
ne pas être en mesure d’utiliser la fonction Bluetooth.
• Sans connexion à Bluetooth active, “BT READY”
apparaît sur la fenêtre d’a chage.
• En cas de dysfonctionnement électrique dû
à des appareils utilisant la même fréquence comme des équipements médicaux, des micro­ondes ou des périphériques LAN sans  l, la connexion est perdue.
• Si quelqu’un se place entre l’équipement
Bluetooth et le lecteur, et ainsi interrompt la communication, la connexion est perdue.
• L’écartement de la distance séparant
l’équipement Bluetooth de l’appareil peut conduire à une diminution du son ; une connexion trop faible peut entraîner une déconnexion si l’espace entre l’équipement Bluetooth et l’appareil est hors plage de fonctionnement de l’équipement Bluetooth.
• Vous déconnectez l’équipement doté de
la technologie sans  l Bluetooth lorsque vous éteignez l’appareil principal ou placez l’équipement à une distance supérieure à 10 mètres de l’appareil principal.
Page 97
27Installation
Raccordement à votre réseau domestique
Cet appareil peut être connecté à un réseau local (LAN) via la prise LAN située à l’arrière de l’appareil.
Reportez-vous à la documentation relative à votre périphérique réseau pour plus d’informations. Raccordez le port LAN du lecteur au port correspondant de votre modem ou routeur à l’aide d’un câble LAN ou Ethernet en vente dans le commerce (CAT5 ou, de préférence, connecteur RJ45). Dans l’exemple de con guration d’une connexion câblée ci-dessous, ce lecteur peut accéder au contenu de chaque ordinateur.
Connexion à un réseau  laire
Routeur
Router
WAN
LAN 1
LAN 2
LAN 3
PC
PC
Lecteur
Broadband
Service haut
Service
débit
Player
3
Installation
REMARQUE
• Maintenez fermement la  che lorsque vous branchez ou débranchez le câble LAN. Au moment de débrancher, ne tirez pas sur le câble LAN mais débranchez-le tout en appuyant sur la languette.
• Ne raccordez pas un câble de téléphone modulaire au port LAN.
• Comme il existe di érentes con gurations de raccordement, suivez les spéci cations de votre opérateur de télécommunications ou de votre prestataire de services internet.
• Le lecteur envoie un signal audio depuis les entrées HDMI à la fois vers la sortie HDMI et les enceintes de l’appareil.
Page 98
28 Installation
Paramétrage réseau
Avant de paramétrer le réseau câblé, vous devez relier votre réseau domestique à internet en haut débit.
S’il existe un serveur DHCP sur le réseau local via une connexion câblée, ce lecteur se verra attribuer automatiquement une adresse IP. Une fois le raccordement physique e ectué, certains réseaux domestiques nécessitent de régler les paramètres réseau du lecteur. Paramétrez l’option [RÉSEAU] comme suit.
1. Sélectionnez l’option [Con g. connexion] dans le menu [Con g.] , puis appuyez sur la
Installation
touche ENTER (
2. Utilisez les touches U/u/I/ sélectionner le mode IP [Dynamique] ou [Statique]. Généralement, sélectionnez [Dynamique] pour attribuer automatiquement une adresse IP.
).
i
pour
REMARQUE
S’il n’existe pas de serveur DHCP sur le réseau et que vous voulez dé nir l’adresse IP manuellement, sélectionnez [Statique], puis réglez les options [Adresse IP], [Masque sous-réseau], [Passerelle] et [Serveur DNS] à l’aide des touches U/u/I/ des touches numériques. Si vous vous trompez en saisissant les chi res, appuyez sur la touche CLEAR pour e acer la partie en surbrillance.
3. Sélectionnez [OK] et appuyez sur ENTER ( ) pour appliquer les paramètres réseau.
4. Le lecteur vous demandera de tester la connexion réseau. Sélectionnez [OK] et appuyez sur la touche ENTER ( ) pour terminer la connexion réseau.
5. Si vous sélectionnez [Test] et appuyez sur la touche ENTER ( ) à l’étape 4 ci-dessus, le statut de la connexion réseau apparaît à l’écran. Vous pouvez aussi le tester via l’option [Statut connexion] du menu [Con g.].
i
et
Page 99
29Installation
Remarques sur la connexion réseau:
• Pour ce faire, après avoir raccordé le lecteur au réseau domestique, éteignez et/ou débranchez rapidement le câble d’alimentation du routeur ou du modem câblé du réseau domestique. Ensuite, rallumez l’appareil et/ou rebranchez le cordon d’alimentation.
• Selon le prestataire de services internet (ISP), le nombre d’appareils pouvant recevoir le service internet peut être limité par les modalités de service applicables. Pour plus de détails, contactez votre ISP.
• Notre entreprise décline toute responsabilité en cas de dysfonctionnement du lecteur et/ou de la fonctionnalité de connexion à internet suite à des erreurs ou problèmes de communication associés à votre connexion internet haut débit ou à tout autre équipement raccordé.
• Les caractéristiques des disques BD­ROM accessibles via la fonctionnalité de connexion à internet ne sont ni créées ni fournies par notre entreprise, aussi ne sommes-nous pas responsables de leur bon fonctionnement ou de leur disponibilité continue. Certains contenus de disque disponibles via la connexion à internet peuvent ne pas être compatibles avec ce lecteur. Si vous avez des questions concernant ces contenus, contactez le producteur du disque.
• Certains contenus internet peuvent nécessiter une connexion très haut débit.
• Même si le lecteur est correctement raccordé et con guré, il se peut que certains contenus internet ne puissent pas être lus à cause d’un encombrement du réseau, de la qualité ou de la largeur de bande de votre service internet, ou de problèmes avec le fournisseur du contenu.
• Certaines opérations liées à la connexion à internet peuvent ne pas être possibles en raison de certaines restrictions  xées par le prestataire de services internet (ISP) fournissant votre connexion internet haut débit.
• Tous les frais facturés par un ISP, notamment, mais sans s’y limiter, les frais de connexion, sont à votre charge.
• Un port LAN 10 Base-T ou 100 Base-TX est nécessaire pour un raccordement câblé à ce lecteur. Si votre service internet ne permet pas un tel raccordement, vous ne pourrez pas brancher le lecteur.
• Vous devez vous servir d’un routeur pour pouvoir utiliser le service xDSL.
• Un modem DSL est nécessaire pour utiliser le service DSL et un modem par câble est nécessaire pour pouvoir utiliser le service de modem par câble. Suivant la méthode d’accès de votre ISP et le contrat d’abonnement souscrit, il est possible que vous ne puissiez pas utiliser la fonctionnalité de connexion à internet o erte par ce lecteur ou que vous soyez limité quant au nombre d’appareils que vous pouvez raccorder simultanément. (Si votre ISP limite l’abonnement à un seul appareil, il est possible que ce lecteur ne puisse pas être raccordé lorsqu’un PC est déjà connecté.)
• L’utilisation d’un “routeur” peut ne pas être autorisée ou être limitée en fonction des règles et restrictions mises en place par votre ISP. Pour plus de détails, contactez directement votre ISP.
• Éteignez tous les appareils réseau non utilisés dans votre réseau domestique local. Certains appareils peuvent générer du tra c sur le réseau.
3
Installation
Page 100
30 Installation
Raccordement d’un périphérique USB
Le lecteur peut lire des  chiers vidéo, musique et des  chiers images contenus dans le périphérique USB.
1. Insérez un périphérique USB au port USB jusqu’à ce qu’il soit bien en place.
Connexion USB
Installation
2. Appuyez sur la touche HOME MENU. Sélectionnez l’option [Film], [Photo] ou [Musique] à l’aide des touches U/u/I/i, puis appuyez sur ENTER ( ).
3. Sélectionnez un  chier à l’aide des touches
U/u/I/i
ENTER ( Vous pouvez véri er à l’écran l’espace disponible sur le périphérique USB.
4. Sélectionnez un autre mode. Retirez le périphérique avec soin.
, et appuyez sur la touche PLAY ou
) pour lire le  chier.
REMARQUE
• Ce lecteur prend en charge les clés mémoire USB et disques durs externes aux formats FAT16, FAT32 et NTFS lors de l’accès aux  chiers (musique, photos et  lms). Toutefois, les fonctionnalités BD-LIVE et d’enregistrement de CD audio ne prennent en charge que les formats FAT16 et FAT32. Lorsque vous utilisez les fonctionnalités BD-LIVE et d’enregistrement d’un CD audio, utilisez une clé USB à mémoire Flash ou un disque dur externe au format FAT16 ou FAT32.
• Le périphérique USB peut être utilisé pour le stockage local a n de visionner des disques BD­LIVE avec internet.
• Cet appareil peut prendre en charge jusqu’à quatre partitions du périphérique USB.
• Ne retirez pas le périphérique USB pendant l’utilisation (lecture, etc.).
• Les périphériques USB nécessitant l’installation d’un programme supplémentaire après la connexion à un ordinateur ne sont pas pris en charge.
• Périphérique USB : périphérique USB prenant en charge les technologies USB 1,1 et USB 2,0.
• Seuls les  chiers vidéo, musicaux et photo peuvent être lus. caractéristiques d’utilisation de chaque  chier, reportez-vous aux pages correspondantes.
• Il est recommandé d’e ectuer des sauvegardes régulières pour éviter la perte de données.
• Si vous utilisez un câble d’extension USB, un concentrateur USB ou un lecteur multiple USB, il se peut que le périphérique USB ne soit pas reconnu.
• Il est possible que certains périphériques USB ne fonctionnent pas avec cet appareil.
• Les appareils photo numériques et les téléphones mobiles ne sont pas compatibles.
• Vous ne pouvez pas connecter le port USB de cet appareil à un PC.
Pour connaître les
Loading...