Pioneer AXM-P8000 INSTALLATION GUIDE

Note:

• Before finally installing the unit, connect the wiring temporarily, making sure it is all connected up properly, and the unit and the system work properly.

• Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions.

• Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle.

• Install the unit where it does not get in the driver’s way and cannot injure the passenger if there is a sudden stop, like an emergency stop.

Installing the display unit

Installation using the bracket

1. Attach bracket (A) to the display unit.

2. Attach bracket (B).

3. Attach the display unit to dashboard or console.

Installation using Velcro tape

• Thoroughly wipe off the surface before affixing the velcro tape.

1. Affix the velcro tape (rough surface) to the display unit.

2. Attach the display unit to dashboard or console.

Velcro tape (soft surface)

Dashboard or console

Display unit

Velcro tape (rough surface)

Drill 2 to 2.5 mm diameter holes.

Dashboard or console

Double faced tape

Tapping screw

Bracket (B)

Binding screw

Washer

Display unit

Screw

Bracket (A)

Installation <ENGLISH>

AXM-P8000

Printed in Japan

<CRD3882-B> UC

INSTALLATION MANUAL

MANUEL D’INSTALLATION

This product conforms to CEMA cord colors. Le code de couleur des câbles utilisé pour ce produit est conforme à CEMA.

Installation using the double faced tape

• Thoroughly wipe off the surface before affixing the double faced tape.

Installing the hide-away unit

Installation using Velcro tape

• Thoroughly wipe off the surface before affixing the velcro tape.

Car mat or chassis

Hide-away unit

Velcro tape

Dashboard or console

Display unit

Double faced tape

Note:

• This unit is for vehicles with a 12-volt battery and negative grounding. Before installing it in a recreational vehicle, truck, or bus, check the battery voltage.

• To avoid shorts in the electrical system, be sure to disconnect the ≠ battery cable before beginning installation.

• Refer to the owner’s manual for details on connecting the power amp and other units, then make connections correctly.

• Secure the wiring with cable clamps or adhesive tape. To protect the wiring, wrap adhesive tape around them where they lie against metal parts.

• Route and secure all wiring so it cannot touch any moving parts, such as the gear shift, handbrake and seat rails. Do not route wiring in places that get hot, such as near the heater outlet. If the insulation of the wiring melts or gets torn, there is a danger of the wiring short-circuiting to the vehicle body.

• Don’t pass the yellow lead through a hole into the engine compartment to connect to the battery. This will damage the lead insulation and cause a very dangerous short.

• Do not shorten any leads. If you do, the protection circuit may fail to work when it should.

• Never feed power to other equipment by cutting the insulation of the power supply lead of the unit and tapping into the lead. The current capacity of the lead will be exceeded, causing overheating.

• When replacing fuse, be sure to use only fuse of the rating prescribed on the fuse holder.

• To avoid short-circuiting, cover the disconnected lead with insulating tape. Especially, insulate the unused speaker leads without fail. There is a possibility of short-circuiting if the leads are not insulated.

• To prevent incorrect connection, the input side of the IP-BUS connector is blue, and the output side is black. Connect the connectors of the same colors correctly.

• If this unit is installed in a vehicle that does not have an ACC (accessory) position on the ignition switch, the red lead of the unit should be connected to a terminal coupled with ignition switch ON/OFF operations. If this is not done, the vehicle battery may be drained when you are away from the vehicle for several hours.

• The black lead is ground. Please ground this lead separately from the ground of high-current products such as power amps. If you ground the products together and the ground becomes detached, there is a risk of damage to the products or fire.

• Cords for this product and those for other products may be different colors even if they have the same function. When connecting this product to another product, refer to the supplied manuals of both products and connect cords that have the same function.

Connecting the Units <ENGLISH>

ACC position

No ACC position

Yellow/black If you use a cellular telephone, connect it via the Audio Mute lead on the cellular telephone. If not, keep the Audio Mute lead free of any connections.

Fuse

This product (Display unit)

This product (Hide-away unit)

Extension cable

1 m (3 ft. 3-1/3 in.)

2 m (6 ft. 7 in)

Orange/white To lighting switch terminal.

Black (ground) To vehicle (metal) body.

Yellow To terminal always supplied with power regardless of ignition switch position.

Red To electric terminal controlled by ignition switch (12 V DC) ON/OFF.

Fuse resistor

3 m (9 ft. 10-3/8 in.)

1.5 m (4 ft. 11-1/4 in.)

3 m (9 ft. 10-3/8 in.)

Multi-DVD player (XDV-P90) (sold separately)

If the connected car stereo or other equipment has both speaker output and RCA output, be sure to connect with RCA output.

IP-BUS cable (supplied with multi-channel processor)

RCA cable (supplied with multi-channel processor)

Optical cable (supplied with multi-channel processor)

Black

7 inch wide AV system display/DVD player (AVX-P8DVD) (sold separately)

Blue

Black

Blue

IP-BUS cable (sold separately)

Black

Video input 1 (VIDEO 1 INPUT)

RCA cable (supplied with Multi-DVD player)

Optical cable (sold separately)

Blue

This product (Display unit)

White +

Gray +

White/black ≠

Gray/black ≠

Front speaker leads

Car stereo

Front left

Front right

Multi-channel processor (DEQ-P8000) (sold separately)

This product (Hide away unit)

If the connected car stereo or other equipment has both speaker output and RCA output, be sure to connect with RCA output.

RCA cable (supplied) (3 m) (9 ft. 10-3/8 in.)

RCA cable (supplied with multi-channel processor)

Optical cable (supplied with multi-channel processor)

AV system display (AVX-7300) (sold separately)

Black

Hide-away TV tuner (e.g. GEX-P6400TV) (sold separately)

AV-BUS cable (supplied with TV tuner)

IP-BUS cable (supplied with TV tuner)

Yellow (VIDEO INPUT)

Car stereo with RCA output

Blue

Black

Blue

Black

Blue

Black

RCA cable (supplied with mulit-DVD player)

Yellow (FRONT VIDEO OUTPUT)

IP-BUS cable (supplied with DVD player)

IP-BUS cable (supplied with multi-channel processor)

Black

This product (Display unit)

Multi-channel processor (DEQ-P8000) (sold separately)

Multi-DVD player (XDV-P90) (sold separately)

This product (Hide away unit)

Multi-CD player (sold separately)

RCA cable (supplied)

(3m) (9 ft. 10-3/8 in.)

Optical cable (supplied with multi-channel processor)

AV-BUS cable (supplied with TV tuner)

IP-BUS cable (supplied with TV tuner)

Yellow (VIDEO INPUT)

Blue

Black

Yellow (FRONT VIDEO OUTPUT)

IP-BUS cable (supplied with DVD player)

IP-BUS cable (supplied with multi-channel processor)

Black

RCA cable (supplied with mulit-DVD player)

Black

Optical cable (sold separately)

When Pioneer Navigation Unit (AVIC-N1) is connected to this unit, make sure the “5.1 ch” mode in the Navigation Unit’s setting is activated.

This product (Display unit)

Subwoofer output or non-fading output (SUBWOOFER OUTPUT or NON-FADING OUTPUT)

Navigation unit (AVIC-N1) (sold separately)

Navigation unit (AVIC-N1) (hide-away unit) (sold separately)

Multi-CD player (sold separately)

This product (Hide away unit)

Hide-away TV tuner (e.g. GEX-P6400TV) (sold separately)

Multi-channel processor (DEQ-P8000) (sold separately)

Blue

Black

Blue

Multi-DVD player (XDV-P90) (sold separately)

+ 2 hidden pages