Pioneer AVH-7650DVD User Manual

English

Español

Português (B)

Français

Italiano

Nederlands

AVH-P7650DVD

This product conforms to new cord colors.
Los colores de los cables de este producto se conforman
con un nuevo código de colores.
As cores dos fios deste produto seguem um novo padrão
de cores.

INSTALLATION MANUAL

INSTALLATION MANUAL

1

Contents

Connecting the Units ................................ 1

Connecting the system ...................................... 3

Connecting the power cord (1) .......................... 4

Connecting the power cord (2) .......................... 5

When connecting to separately sold power

amp ............................................................ 7

When connecting with a rear view camera ...... 9

When connecting the external video

component and the display ...................... 11

Attaching the noise filters .............................. 12

Installation ................................................ 13

Installing the hide-away unit .......................... 13

DIN Front/Rear-mount .................................... 14

DIN Front-mount ............................................ 14

DIN Rear-mount .............................................. 15

Installing the remote control unit .................... 16

WARNING:

• To avoid the risk of accident and the
potential violation of applicable laws,
the front DVD or TV (sold separately)
feature should never be used while the
vehicle is being driven. Also, Rear
Displays should not be in a location
where it is a visible distraction to the
driver.

• In some countries or states the viewing
of images on a display inside a vehicle
even by persons other than the driver
may be illegal. Where such regulations
apply, they must be obeyed and this
unit’s DVD features should not be used.

CAUTION:

• PIONEER does not recommend that
you install or service your display your­self. Installing or servicing the product
may expose you to risk of electric shock
or other hazards. Refer all installation
and servicing of your display to autho­rized Pioneer service personnel.

• Secure all wiring with cable clamps or
electrical tape. Do not allow any bare
wiring to remain exposed.

• Do not drill a hole into the engine com­partment to connect the yellow lead of
the unit to the vehicle battery. Engine
vibration may eventually cause the insu­lation to fail at the point where the wire
passes from the passenger compartment
into the engine compartment. Take
extra care in securing the wire at this
point.

• It is extremely dangerous to allow the
display lead to become wound around
the steering column or gearshift. Be sure
to install the display in such a way that
it will not obstruct driving.

• Make sure that wires will not interfere
with moving parts of the vehicle, such as
the gearshift, parking brake or seat slid­ing mechanism.

• Do not shorten any leads. If you do, the
protection circuit may fail to work
properly.

Connecting the Units

English

Español

Português (B)

Français

Italiano

Nederlands

2

Note:

• This unit is for vehicles with a 12-volt battery and
negative grounding. Before installing it in a recre­ational vehicle, truck, or bus, check the battery
voltage.

• To avoid shorts in the electrical system, be sure to
disconnect the ≠ battery cable before beginning
installation.

• Refer to the owner’s manual for details on
connecting the power amp and other units, then
make connections correctly.

• Secure the wiring with cable clamps or adhesive
tape. To protect the wiring, wrap adhesive tape
around them where they lie against metal parts.

• Route and secure all wiring so it cannot touch any
moving parts, such as the gear shift, handbrake
and seat rails. Do not route wiring in places that
get hot, such as near the heater outlet. If the insu­lation of the wiring melts or gets torn, there is a
danger of the wiring short-circuiting to the vehicle
body.

• Don’t pass the yellow lead through a hole into the
engine compartment to connect to the battery.
This will damage the lead insulation and cause a
very dangerous short.

• Do not shorten any leads. If you do, the protection
circuit may fail to work when it should.

• Never feed power to other equipment by cutting
the insulation of the power supply lead of the unit
and tapping into the lead. The current capacity of
the lead will be exceeded, causing overheating.

• When replacing the fuse, be sure to only use a
fuse of the rating prescribed on the fuse holder.

• Since a unique BPTL circuit is employed, never
wire so the speaker leads are directly grounded or
the left and right ≠ speaker leads are common.

• If the RCA pin jack on the unit will not be used,
do not remove the caps attached to the end of the
connector.

• Speakers connected to this unit must be high­power with minimum rating of 50 W and imped­ance of 4 to 8 ohms. Connecting speakers with
output and/or impedance values other than those
noted here may result in the speakers catching
fire, emitting smoke, or becoming damaged.

• When this product’s source is switched ON, a
control signal is output through the blue/white
lead. Connect to an external power amp’s system
remote control or the car’s Auto-antenna relay
control terminal (max. 300 mA 12 V DC). If the
car features a glass antenna, connect to the anten­na booster power supply terminal.

• When an external power amp is being used with
this system, be sure not to connect the blue/white
lead to the amp’s power terminal. Likewise, do
not connect the blue/white lead to the power ter­minal of the auto-antenna. Such connection could
cause excessive current drain and malfunction.

• To avoid a short-circuit, cover the disconnected
lead with insulating tape. Insulate the unused
speaker leads without fail. There is a possibility of
a short-circuit if the leads are not insulated.

• To prevent incorrect connection, the input side of
the IP-BUS connector is blue, and the output side
is black. Connect the connectors of the same col­ors correctly.

• This unit cannot be installed in a vehicle that
does not have an ACC (accessory) position on
the ignition switch. (Fig. 1)

Fig. 1

• The black lead is ground. Please ground this lead
separately from the ground of high-current prod­ucts such as power amps.
If you ground the products together and the
ground becomes detached, there is a risk of dam­age to the products or fire.

No ACC positionACC position

• Cords for this product and those for other prod­ucts may be different colors even if they have
the same function. When connecting this product
to another product, refer to the supplied manuals
of both products and connect cords that have the
same function.

C

C

A

O

F

N

F

O

S

T

A

R

T

O

F

N

F

O

S

T

A

R

T

3

Connecting the Units

Connecting the system

Fig. 2

Multi-CD player
(sold separately)

IP-BUS cable

3 m

This product

IP-BUS input
(Blue)

Hide-away TV tuner
(e.g. GEX-P6450TVP)
(sold separately)

AV-BUS input (Blue)

AV-BUS cable (supplied
with TV tuner)

IP-BUS cable (supplied
with TV tuner)

10 cm

Black

Blue

Black Blue

Black

Blue

30 pin cable (supplied)

21 pin cable (supplied)

Violet

3 m

15 cm

Violet

Hide-away unit
(supplied)

Antenna jack

Antenna cable (supplied)

3 m

Black

15 cm

Auto-EQ&TA mic jack
See the operation manual.

Connecting the power cord (1)

English

Español

Português (B)

Français

Italiano

Nederlands

Fig. 3

4

Fuse holder

Black

Black/white

Hide-away unit

Yellow
To terminal always supplied
with power regardless of
ignition switch position.

Black (ground)
To vehicle (metal) body.

≠

Center speaker

+

5

Connecting the Units

Connecting the power cord (2)

Yellow
To terminal always supplied
with power regardless of
ignition switch position.

Fuse holder

Fuse resistor

Red
To electric terminal controlled
by ignition switch (12 V DC)
ON/OFF.

Black (ground)
To vehicle (metal) body.

Orange/white
To lighting switch terminal.

White

White/black

Gray

Gray/black

Green

Green/black

Violet

Violet/black

Front speaker

Rear speaker

Front speaker

Rear speaker

Fuse resistor

This product

Left Right

+

≠

+

≠

+

≠

+

≠

Yellow/black
If you use an equipment with Mute function, wire
this lead to the Audio Mute lead on that equipment.
If not, keep the Audio Mute lead free of any
connections.

Violet/white

See the section “When connecting
with a rear view camera”.

6

English

Español

Português (B)

Français

Italiano

Nederlands

Note:

• The position of the parking brake switch depends
on the vehicle model. For details, consult the
vehicle Owner’s Manual or dealer.

Connection method

Clamp the lead.1. 2. Clamp firmly with

needle-nosed
pliers.

WARNING

Blue/white
To system control terminal of the power amp
or Auto-antenna relay control terminal
(max. 300 mA 12 V DC).

With a 2 speaker system, do not connect anything
to the speaker leads that are not connected to speakers.

Parking brake
switch

Power supply side

Ground side

Light green
Used to detect the ON/OFF status of the parking brake.
This lead must be connected to the power supply side of the parking
brake switch.

LIGHT GREEN LEAD AT POWER CONNECTOR IS DESIGNED TO
DETECT PARKED STATUS AND MUST BE CONNECTED TO THE
POWER SUPPLY SIDE OF THE PARKING BRAKE SWITCH. IMPROPER
CONNECTION OR USE OF THIS LEAD MAY VIOLATE APPLICABLE
LAW AND MAY RESULT IN SERIOUS INJURY OR DAMAGE.

Fig. 4

When connecting to separately sold power amp

7

Connecting the Units

This product

Front output
(FRONT OUTPUT)

Subwoofer output
(SUBWOOFER OUTPUT)

Rear output
(REAR OUTPUT)

15 cm

23 cm

15 cm

Center output
(CENTER OUTPUT)

23 cm

Noise filter
(small)

Lock tie

See the section “Attaching the
noise filters”.

Blue/white
To system control terminal of the power amp
or Auto-antenna relay control terminal
(max. 300 mA 12 V DC).

English

Español

Português (B)

Français

Italiano

Nederlands

Fig. 5

8

Power amp
(sold separately)

Power amp
(sold separately)

Power amp
(sold separately)

System remote control

RCA cables
(sold separately)

Front speaker

Rear speaker

Subwoofer

Front speaker

Rear speaker

Center speaker

Left Right

Perform these connections when using
the optional amplifier.

Power amp
(sold separately)

9

Connecting the Units

When connecting with a rear view camera

When using this product with a rear view camera, automatic switching to video from a
rear view camera when the gear shift is moved to REVERSE (R) position is possible.

WARNING:

• USE INPUT ONLY FOR REVERSE OR MIRROR IMAGE REAR VIEW CAMERA.
OTHER USE MAY RESULT IN INJURY OR DAMAGE.

CAUTION:

• The screen image may appear reversed.

• The rear view camera function is to use this product as an aid to keep an eye on trailers,
or backing into a tight parking spot. Do not use this function for entertainment purpos­es.

• The object in rear view may appear closer or more distant than in reality.

English

Español

Português (B)

Français

Italiano

Nederlands

10

Fig. 6

Connection method

Clamp the lead.1. 2. Clamp firmly with

needle-nosed
pliers.

CAUTION

Pioneer recommends the use of
a camera which outputs mirror
reversed images, otherwise
screen image may appear
reversed.

Hide-away unit

Fuse resistor

8 m

Extension lead (supplied)

Rear view camera

Violet/white
Of the two lead wires connected to the back
lamp, connect the one in which the voltage
changes when the gear shift is in the REVERSE
(R) position.

RCA cable
(sold separately)

Note:

• It is necessary to set to BACK UP CAMERA in SETUP when connecting the rear view camera.

15 cm

To video output

This product

11

Connecting the Units

When connecting the external video component and the display

Fig. 7

• It is necessary to set to AV INPUT in SETUP when connecting the external video com-

ponent.

When using a display connected to rear video output

This product’s rear video output is for connection of a display to enable passengers in the
rear seats to watch the DVD or Video CD.

WARNING:

• NEVER install the display in a location that enables the Driver to watch the DVD or Video CD
while Driving.

• NEVER connect rear audio output (REAR OUT) to sold separately power amp.

Hide-away unit

External video
component
(sold separately)

RCA cables
(sold separately)

Display with
RCA input jacks

RCA cables
(sold separately)

To video input

To audio inputs

To video output

To audio outputs

12

English

Español

Português (B)

Français

Italiano

Nederlands

Attaching the noise filters

To prevent the noise, use the supplied noise filters correctly.

Fig. 8

This product

Noise filter
(large)

Lock tie

Other than
speaker leads

Noise filter
(small)

Lock tie

Speaker leads

Hide-away unit

Noise filter
(large)

Lock tie

Noise filter
(large)

Noise filter
(small)

Noise filter
(large)

Lock tie

Lock tie

Noise filter
(large)

13

Installation

Note:

• Before making a final installation of the unit,
temporarily connect the wiring to confirm that the
connections are correct and the system works
properly.

• Use only the parts included with the unit to
ensure proper installation. The use of unautho­rized parts can cause malfunctions.

• Consult with your nearest dealer if installation
requires the drilling of holes or other modifica­tions of the vehicle.

• Install the unit where it does not get in the dri­ver’s way and cannot injure the passenger if there
is a sudden stop, like an emergency stop.

• Do not place the display in a position where it
will impede the driver’s visibility or affect the
operation of your vehicle’s air bags.

• The semiconductor laser will be damaged if it
overheats, so don’t install the unit anywhere hot
— for instance, near a heater outlet.

• If installation angle exceeds 30° from horizontal,
the unit might not give its optimum performance.
(Fig. 9)

Fig. 9

• When installing, to ensure proper heat dispersal
when using this unit, make sure you leave ample
space behind the rear panel and wrap any loose
cables so they are not blocking the vents.

• To ensure proper heat dissipation of this product,
take special care not to block the cooling fan side
of this product.

• When mounting the hide-away unit, make sure
none of the leads are trapped between the hide­away unit and the surrounding metalwork or fit­tings.

• Do not mount the hide-away unit near the heater
outlet, where it would be affected by heat, or near
the doors, where rainwater might splash onto it.

• Before drilling any mounting holes always check
behind where you want to drill the holes. Do not
drill into the gas line, brake line, electrical wiring
or other important parts.

• If the hide-away unit is installed in the passenger
compartment, anchor it securely so it does not
break free while the car is moving, and cause
injury or an accident.

• If the hide-away unit is installed under a front
seat, make sure it does not obstruct seat move­ment. Route all leads and cords carefully around
the sliding mechanism so they do not get caught
or pinched in the mechanism and cause a short
circuit.

Installing the hide-away unit

Mounting with Velcro Tape

Thoroughly wipe off the surface
before affixing the velcro tape.

Fig. 10

30°

Hide-away unit

Velcro tape
(large) (hard)

Velcro tape
(large) (soft)

Car mat or chassis

14

English

Español

Português (B)

Français

Italiano

Nederlands

DIN Front/Rear-mount

This unit can be properly installed
either from “Front” (conventional DIN
Front-mount) or “Rear” (DIN Rear­mount installation, utilizing threaded
screw holes at the sides of unit chas­sis). For details, refer to the following
illustrated installation methods.

Before installing the unit

• Remove the frame and the hold­er. (Fig. 11)

Pull out to remove the frame and then
loosen the screws (2 × 3 mm) to
remove the holder. (When reattaching
the frame, point the side with a groove
downwards and attach it.)

Fig. 11

DIN Front-mount

Installation with the rubber bush

1. Decide the position of the side
brackets. (Fig. 12)

When installing in a shallow space,
change the position of side brackets. In
this case, stick conceal tape on parts
that protrude from the dashboard.

Fig. 12

Conceal tape

Side bracket

Flush surface screw (5 × 6 mm)

Holder

Frame

Screw (2 × 3 mm)