Pilz PSEN 2.1p-34 Data Sheet

Units

PSENmag

PSEN 2.1p-34

2.2

PSEN 2.1p-342.2SEN-D-2-034-2007-03UnitsPSENmagPSEN 2.1p-34PSEN 2.1p-34

Magnetic safety switches for monitor­ing the position of movable guards in
accordance with EN 60947-5-3

Approvals

PSEN 2.1p-34





Unit features

` The actuator PSEN 2,1-10 belongs

to the safety switch

` 2 reed contacts (1 N/C, 1 N/O)
` Assured operating distance: 6 mm
` Assured release distance: 25 mm
` Square design
` Works magnetically
` Switching voltage 24 VDC
` Series connection via PSEN i1 in-

terface

` LED to display switch status

Unit description

The safety switch meets the require­ments of EN 60204-1 and IEC 60204-

1.
The safety switch only complies with
EN 60947-5-3 in conjunction with the
actuator PSEN 2,1-10 and its ap­proved evaluation devices.
The safety switch should only be con­nected to the evaluation devices listed
under "Connections".

Function description

If the actuator is within the response
range, the magnets switch the reed
contacts on the safety switch. If the
actuator is outside the response range
(safety gate open), the reed contacts
on the safety switch will switch.

Block diagram

Safety switch

Actuator

Magnet

2.2-146

SEN-D-2-034-2007-03Pilz GmbH & Co. KG, Sichere Automation, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany

Telephone: [phone], Telefax: [phone], E-Mail: [e-mail]

Units

PSENmag

PSEN 2.1p-34

Operating distances

Seitenversatz/Lateral offset/

Décalage latéral

active area

aktive Fläche

surface active

Lateral and vertical offset

Assured operating distance Sao in mm

Höhenversatz/Height offset/
Décalage en hauteur

3,02,01,0 4,0
1,0
2,0
3,0
4,0

Seitenversatz/Lateral

offset/Décalage latéral

-

-4,0

5,0

3,04,54,55,5 4,0
2,54,54,55,0 3,5
0,53,54,54,5 2,5

--

Assured release distance Sar:
Max. 25 mm with all vertical and lateral
offsets

The stated values are valid at a tem­perature of 20 °C.

Wiring

Please note:

` Information given in the “Technical

details” must be followed.

Höhenversatz/Height offset/

Décalage en hauteur

` Calculation of the max. cable runs

in the input circuit:

l

max

R

lmax

=

I

max

Rl / km

= max. overall cable resist-

R

lmax

ance (see Technical details)

/ km = cable resistance/km

R

l

` When using evaluation devices with

delay-on de-energisation contacts,
please note:
–Delay time ≤ 30 s: Delay-on de-

energisation contacts satisfy the
requirements of category 3 in ac­cordance with EN 954-1 and the
requirements of a PDF with sin­gle-fault tolerance (PDF-S).

–Delay time ≥ 30 s: Delay-on de-

energisation contacts satisfy the
requirements of Category 1 in
accordance with EN 954-1 and
the requirements of a PDF with
designed reliability (PDF-D).

Schaltabstand/Operating distance/

s

ar

s

ao

s

omin

Portee de travail

= 25

= 6

= 0,5

Ein/On/Marche
Aus/Off/Arrêt

` In the following commissioning cas-

es, check the function that detects
shorts across contacts:
– On evaluation devices with DC

supply voltage: Overall cable re­sistance ≥ 15 Ohms per channel

– On evaluation devices with AC

supply voltage: Overall cable re­sistance ≥ 25 Ohms per channel

– For details of how to perform the

test for shorts across the con­tacts, please refer to the operat­ing manual for the relevant
evaluation device.

Connections

NOTICE

The colour marking for the connection
lead only applies for the cable that Pilz
supplies as an accessory.
The safety switch is shown in an unop­erated condition.

2.2

Assignment of the 4-pin M8 male connec­tor

Pilz GmbH & Co. KG, Sichere Automation, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany
Telephone: [phone], Telefax: [phone], E-Mail: [e-mail]

2

1

4

3

1

2

3 +

4

SEN-D-2-034-2007-03

2.2-147

Units

PSENmag

PSEN 2.1p-34

` Connection to PNOZelog

2.2

ohne Querschlusserkennung/without detection of shorts
across contacts/sans détection des courts-circuits entre les
canaux
PNOZ e3.1p
PNOZ e3vp 10 s
PNOZ e3vp 300 s

with detection of shorts across contacts
PNOZ e3.1p
PNOZ e3vp 10 s
PNOZ e3vp 300 s

` Connection to PNOZmulti

Schutztür/safety gate/protecteur mobile
Schaltertyp 2/switchtype 2/type du capteure 2
I0, I1: Eingänge/inputs/entrées
T0, T1: Taktausgänge/test pulse outputs/sorties
impulsionelles

braun/brown/marron

A1

weiß/white/blanc

S12

blau/blue/bleu

schwarz/black/noir

S24

Nicht-Ex-Bereich/Non-Ex
area/Zone Non Ex

braun/brown/marron

S11

weiß/white/blanc

S12

blau/blue/bleu

S23

schwarz/black/noir

S24

Nicht-Ex-Bereich/Non-Ex
area/Zone Non Ex

T0

I0

T1

I1

Nicht-Ex-Bereich/Non-Ex
area/Zone Non Ex

1

2
3

4

Ex-Bereich/Ex area/
Zone Ex

1

2
3

4

Ex-Bereich/Ex area/
Zone Ex

braun/brown/marron
weiß/white/blanc
blau/blue/
schwarz/black/noir

Ex-Bereich/Ex area/
Zone Ex

bleu

1
2

3
4

2.2-148

` Connection to PSS with and with-

out SafetyBUS p

Schutztür/safety gate/protecteur mobile
Schaltertyp 3/switchtype 3/type du capteure 3
I0, I1: Eingänge/inputs/entrées
O16, O17: Taktausgänge/test pulse outputs/sorties
impulsionelles

Nicht-Ex-Bereich/Non-Ex
area/Zone Non Ex

CAUTION!

The safety switches may only be oper-

standard function block SB064 or
SB066.

ated on a PSS in conjunction with

Telephone: [phone], Telefax: [phone], E-Mail: [e-mail]

O 16

I 00

O 17

I 01

braun/brown/marron
weiß/white/blanc

blau/blue/
schwarz/black/noir

bleu

Ex-Bereich/Ex area/
Zone Ex

1

2
3

4

SEN-D-2-034-2007-03Pilz GmbH & Co. KG, Sichere Automation, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany

Units

PSENmag

PSEN 2.1p-34

Installation

` The unit can be installed in any po-

sition. However, safety switches
and actuators must be positioned
opposite each other in parallel:

` If possible, do not install the safety

switch and actuator on to ferromag­netic material. Changes to the oper­ating distances are to be expected.
In this case, use the spacer availa­ble under order number 534 310.

` Safety switches and actuators

should only be secured using M4
screws with a flat head (e.g. M4
cheese-head or pan head screws).
Torque setting max. 1 Nm. Use
screws made of non-magnetic ma­terial (e.g. Messing).

` The distance between two systems

comprising safety switch and actu­ator must be at least 25 mm.

` Safety switch and actuator

– Keep away from iron swarf
– Do not expose to strong mag-

netic fields

– Do not expose to heavy shock or

vibration

– Do not use as a limit stop

2.2

Adjustment

` The safety switch may only be used

with the corresponding actuator
PSEN 2,1-10.

` Always test the function with one of

the approved evaluation devices.

` The LED lights when the reed con-

tacts are unoperated (safety device
open or safety switch and actuator
wrongly adjusted). The LED is in the
safety switch's N/C circuit. The LED
goes out when the reed contacts
are operated.

` The stated operating distances (see

Technical details) only apply when
the safety switch and actuator are
installed facing each other in paral­lel. Operating distances may devi­ate if other arrangements are used.
Note the maximum permitted later­al and vertical offset (see "Operat­ing distances" and "Max. lateral
and vertical offset").

Pilz GmbH & Co. KG, Sichere Automation, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany
Telephone: [phone], Telefax: [phone], E-Mail: [e-mail]

SEN-D-2-034-2007-03

2.2-149

Units

PSENmag

PSEN 2.1p-34

2.2

NOTICE

This data sheet is only intended for use
during configuration. For installation
and operation, please refer to the op­erating instructions supplied with the
unit.

Dimensions

Safety switch

13

Actuator

13

6,5

19

19

8,5

8,5

4,5

4,5

22

22

36

6,8

M8x1

10,6

26

26

36

Technical details

Switching distances
Assured operating distance S
Min. operating distance S
Assured release distance S
Switching voltage 24 V
Max. switching current for reed contacts 10.00 mA
Max. breaking capacity for reed contacts 0.3 W
Max. switch frequency 1 Hz
Actuator PSEN 2,1-10
Ambient temperature -25 - 70 °C
Vibration to EN 60947-5-2
Frequency 10 - 55 Hz
Amplitude 1.00 mm
Shock stress 30 g , 11 ms
Connection type M8
Cable LiYY 4 x 0,25 mm
Protection type IP65
Housing material PBT

ao

omin

ar

6 mm

0.5 mm
25 mm

2

2.2-150

SEN-D-2-034-2007-03Pilz GmbH & Co. KG, Sichere Automation, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany

Telephone: [phone], Telefax: [phone], E-Mail: [e-mail]

Units

PSENmag

PSEN 2.1p-34

Technical details

Dimensions
Safety switch
Height 45.0 mm
Width 26.0 mm
Depth 13.0 mm
Actuator
Height 36 mm
Width 26 mm
Depth 13 mm
Weight
Safety switch 15 g
Actuator 20 g

The standards current on 2007-03 apply.

Order reference

Type Quantity Operation Features Order no.

PSEN 2.1p-34 1/1 magnetic Safety switch/actuator 502 234

2.2

Pilz GmbH & Co. KG, Sichere Automation, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany
Telephone: [phone], Telefax: [phone], E-Mail: [e-mail]

SEN-D-2-034-2007-03

2.2-151