Pilz PSEN 1.2p-20 Data Sheet

Units

PSENmag

PSEN 1.2p-20

2.2

PSEN 1.2p-202.2SEN-D-2-023-2007-03UnitsPSENmagPSEN 1.2p-20PSEN 1.2p-20

Magnetic safety switches for monitoring the position of movable guards in accordance with EN 60947-5-3

Approvals

PSEN 1.2p-20



Unit features

` The actuator PSEN 1,2-20 belongs

to the safety switch

` 2 reed contacts (N/O) ` Assured operating distance: 8 mm ` Assured release distance: 26 mm ` Round design ` Works magnetically ` Switching voltage 24 VDC

Unit description

The safety switch meets the requirements of EN 60204-1 and IEC 60204-

1. The safety switch only complies with EN 60947-5-3 in conjunction with the actuator PSEN 1,2-20 and its approved evaluation devices. The safety switch should only be connected to the evaluation devices listed under "Connections".

Function description

If the actuator is within the response range, the magnets switch the reed

contacts on the safety switch. If the actuator is outside the response range (safety gate open), the reed contacts on the safety switch will switch.

Block diagram

Safety switch

Actuator

Magnet

2.2-66

SEN-D-2-023-2007-03Pilz GmbH & Co. KG, Sichere Automation, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany

Telephone: +49 711 3409-0, Telefax: +49 711 3409-133, E-Mail: pilz.gmbh@pilz.de

Units

PSENmag

PSEN 1.2p-20

Operating distances

Höhenversatz/Height offset/

Décalage en hauteur

active area

aktive Fläche

surface active

Lateral and vertical offset

` Assured operating distance Sao in

Höhenversatz/Height offset/

Höhenversatz/Height offset/ Décalage en hauteur

Décalage en hauteur

5,0

5,5

5,0

5,57,07,57,5 7,0

5,57,07,57,5 7,0 5,57,07,07,5 6,5

5,57,07,07,5 6,5

5,57,07,07,0 6,0

5,0

5,0 4,5

4,5

3,02,01,0 4,0

1,0

1,0 2,0

2,0 3,0

3,0

6,0

4,0

4,0 5,0

5,0

Seitenversatz/Lateral

offset/Décalage latéral

Seitenversatz/Lateral

offset/Décalage latéral

6,0

6,56,5

6,56,5 6,06,0 6,0

6,06,0 6,0

` Assured release distance S

Max. 26 mm with all vertical and

lateral offsets The stated values are valid at a temperature of 20 °C.

Wiring

Please note:

` Information given in the “Technical

details” must be followed.

Seitenversatz/Lateral offset/

Décalage latéral

Kerbe

Kerbe Indentation

Indentation

Indentation Enchose

Enchose

` Calculation of the max. cable runs

in the input circuit:

max

lmax

max

Rl / km

= max. overall cable resist-

lmax

ance (see Technical details)

/ km = cable resistance/km

` When using evaluation devices with

delay-on de-energisation contacts, please note: –Delay time ≤ 30 s: Delay-on de-

energisation contacts satisfy the requirements of category 3 in accordance with EN 954-1 and the requirements of a PDF with single-fault tolerance (PDF-S).

–Delay time ≥ 30 s: Delay-on de-

energisation contacts satisfy the requirements of Category 1 in accordance with EN 954-1 and the requirements of a PDF with designed reliability (PDF-D).

Schaltabstand/Operating distance/

= 26

= 8

= 0,5

omin

Portee de travail

Ein/On/Marche

Ein/On/Marche Aus/Off/Arrêt

Aus/Off/Arrêt

` In the following commissioning cas-

es, check the function that detects shorts across contacts: – On evaluation devices with DC

supply voltage: Overall cable resistance ≥ 15 Ohms per channel

– On evaluation devices with AC

supply voltage: Overall cable resistance ≥ 25 Ohms per channel

– For details of how to perform the

test for shorts across the contacts, please refer to the operating manual for the relevant evaluation device.

Connections

NOTICE

The colour marking for the connection lead only applies for the cable that Pilz supplies as an accessory. The safety switch is shown in an unoperated condition.

2.2

Belegung des 4-pol. M8Stiftsteckers/Assignment of the 4-pin M8 male connector/Repérage du connecteur mâle M8 à 4 pôles

Pilz GmbH & Co. KG, Sichere Automation, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany Telephone: +49 711 3409-0, Telefax: +49 711 3409-133, E-Mail: pilz.gmbh@pilz.de

SEN-D-2-023-2007-03

2.2-67

+ 4 hidden pages