Импортер на территорию России и Таможенного Союза: ООО “ФИЛИПС”,
Российская Федерация, 123022 г. Москва, ул. Сергея Макеева, д.13, тел. +7 495 961-1111
Для бытовых нужд
Класс защиты от поражения электрическим током: Класс I
Сделано в Индонезии
Ресей және Кедендік Одақ территориясына импорттаушы: ФИЛИПС ЖШҚ, Ресей Федерациясы,
123022 Мәскеу қаласы, Сергей Макеев көшесі, 13-үй, тел. +7 495 961-1111.
Congratulations on your purchase and welcome to Philips! To fully benet from the
support that Philips oers, register your product at www.philips.com/welcome.
Read this user manual and the important information leaet carefully before you use the
appliance. Save them for future reference.
The OptimalTEMP technology enables you to iron all types of ironable fabrics, in any
order, without adjusting the iron temperature and without sorting your garments.
It is safe to just rest the hot soleplate directly on the ironing board without putting back
to the iron platform. This will help reduce the stress on your wrist.
This iron has been approved by The Woolmark Company Pty Ltd for the ironing of woolonly products, provided that the garments are ironed according to the instructions on the
garment label and those issued by the manufacturer of this iron. R0000. The Woolmark
symbol is a certication mark in many countries.
sensor
This appliance uses the most advanced sensor that detects your iron
movement precisely and delivers intelligent steam release for perfect results. Our
advanced sensor knows precisely how your iron is moving and when it’s
standing still. Just switch to mode, and you’ll always have the perfect amount
of steam, when you need it to get rid of your wrinkles faster.
Turbo steam pump
We add a turbo steam pump in this appliance to boost up to 50% more steam directly
through fabrics, so creases quickly disappear.
ENGLISH
8
Using the appliance
Note: The iron may give o some smoke when you use it for the rst time. This ceases
after a short while.
Type of water to use
This appliance has been designed to be used with tap water. However, if you live in an
area with hard water, fast scale build-up may occur. Therefore, it is recommended to use
distilled or demineralized water to prolong the lifetime of the appliance.
Do not use perfumed water, water from the tumble dryer, vinegar, starch, descaling
agents, ironing aids, chemically descaled water or other chemicals, as they may cause
water spitting, brown staining or damage to your appliance.
Ironable fabrics
1 Check whether the garment is ironable by reading the label on the garment (Fig. 1-3).
Do not iron non-ironable fabrics. Prints on the garment are not ironable either.
Steam settings
1 To change steam settings, tilt the iron up slightly (about 20 degree and more), and
press steam button on top of the handle (Fig. 1-5)
Note: All steam settings are equipped with OptimalTEMP technology and are safe to
use on all ironable fabrics.
- ( setting) (Fig. 1-6): enabled by the sensor, perfect amount of steam
is produced automatically when needed during movement of the iron. Steam stops
when the iron is not moved or put to vertical position.
It is recommended to use the setting for ultimate convenience on all garments.
- (MAX setting) (Fig. 1-7): maximum constant steam is delivered continuously for
stubborn creases. For best result on tough fabrics such as cotton, jeans and linen, it
is recommended to use the MAX setting. Steam stops when the iron is put to vertical
position.
delivered continuously for garments with less creases. This setting also saves energy.
Steam stops when the iron is put to vertical position.
- (ionic setting) (specic types only) (Fig. 1-9): deep and powerful ionic steam
bursts are produced for more hygienic ironing.
- (steam o setting) (Fig. 1-10): select this setting to iron without steam.
Tip: In any steam setting, you can press the steam button during ironing for more steam.
Auto shut-o
The safety auto-o function automatically switches o the appliance if it has not been
used for 2 minutes resting on its soleplate or 8 minutes resting on its backplate. The
display panel ashes to indicate the appliance is at auto-o status.
To let the appliance heat up again, pick up the appliance or move it slightly. The display
panel turns to breathing and the appliance starts to heat up.
ENGLISH
9
Cleaning and maintenance
For more information on how to performance clean and maintenance on the iron, refer to
the videos in this link : http://www.philips.com/descaling-iron.
Cleaning the soleplate
1 Unplug the appliance and let it cool down.
2 Pour any remaining water out of the water tank.
3 Wipe akes and any other deposit o the soleplate with a damp cloth and a non-
abrasive (liquid) cleaning agent.
Note: To keep the soleplate smooth, avoid hard contact with metal objects. Never use a
scouring pad, vinegar or other chemicals to clean the soleplate.
Quick Calc Release (specic types only)
IMPORTANT: The Quick Calc Release automatically collects loose scale particles during
ironing. After 1 to 3 months of use, the Calc-Clean reminder light starts ashing to
remind you to use the Quick Calc Release function (Fig. 2-1). This is to remove scales
collected from your iron to prolong its life. When the Calc-Clean reminder light is
ashing, the iron does not heat up.
Tip: The Quick Calc Release function can be used at any time, even when the reminder
light is not activated yet. If you live in a hard water area, use the function more
frequently.
Do not perform the Quick Calc Release when the iron is hot. Do not pour water into the
Quick Calc Release opening.
1 Unplug the appliance (Fig. 2-2) and make sure that the appliance is cool (Fig. 2-3).
2 Hold the appliance in vertical position over the sink.
3 Flip up the lever of Quick Calc Release collector (Fig.2-4) and pull out the collector
(Fig.2-5).
4 Clean the Quick Calc Release collector with water (Fig. 2-6, Fig. 2-7).
5 Gently shake the appliance to allow scale particles to fall out (Fig. 2-8).
6 Insert the Quick Calc Release collector back into the appliance (Fig. 2-10).
7 Push down the lever (“click”) to lock the collector (Fig. 2-11).
Calc-Clean (specic types only)
IMPORTANT: After 1 to 3 months of use, the Calc-Clean reminder light starts ashing to
remind you to use the Calc-Clean function (Fig. 3-1). This is to remove scales in your iron
to prolong its life.
Tip: The Calc-Clean function can be used at any time, even when the reminder light is
not activated yet. If you live in a hard water area, use the function more frequently.
1 Make sure that the steam slider is set to “steam o” position.
ENGLISH
10
2 Make sure there is enough water (more than 3/4) in the water tank. If there is not
enough water, unplug the iron, ll the water to MAX indication (Fig.3-2) and plug in
the iron again (Fig.3-3).
Do not pour vinegar or other descaling agents into the water tank.
3 Wait for the iron to heat up. This takes about 2 minutes (Fig.3-3).
Note: the Calc-Clean reminder light turns o during heating up.
4 Unplug the iron when the ‘iron ready’ light stops breathing (Fig. 3-4).
5 Hold the iron over the sink. Keep pushing the Calc-Clean button and gently shake
the iron forth and back until all water in the water tank has been used up (Fig. 3-5).
Scales is ushed out, steam and boiling water also come out of the soleplate.
Note: Repeat steps 2 to 5 if the water that comes out of the appliance still contains
scale particles.
6 Plug in the appliance and let the appliance heat up to dry the soleplate. This takes
about 2 minutes (Fig.3-6).
7 Unplug the appliance. Move the appliance gently over a piece of cloth to remove any
water stains on the soleplate (Fig. 3-7).
Troubleshooting
This chapter summarises the most common problems you could encounter with the
appliance. If you
www.philips.com/support for a list of frequently asked questions or contact the
Consumer Care Centre in your country.
ProblemPossible causeSolution
The iron does
not produce any
steam.
The steam setting
does not change
when I press the
steam button on
top of the handle.
The ironing board
cover becomes
wet or there are
water droplets on
the garment during
ironing.
are unable to solve the problem with the information below, visit
There is not enough water
in the tank.
The steam setting is set to
“steam o”
The iron is not ready.Wait until the iron is ready (the light on the
The steam button changes
steam settings only
when the iron is tilted. In
horizontal position, the
steam button serves as
a trigger to release extra
steam in any setting.
Steam has condensed on
the ironing board cover
after a long ironing session.
Fill the water tank.
Tilt the iron up and press the steam button on
top of the handle to select a steam setting.
display panel stops ashing).
Tilt the iron up slightly and press the steam
button to change steam setting.
This is designed to ensure the consumers do
not accidentally change the steam setting
while ironing.
Replace the ironing board cover if the foam
material has worn out. You can also add an
extra layer of felt material under the ironing
board cover to prevent condensation on the
ironing board. You can buy felt in a fabric shop.
ENGLISH
11
ProblemPossible causeSolution
Water droplets
drips onto the
garment during
ironing.
The iron does not
produce a steam
boost
Dirty water
and impurities
come out of the
soleplate during
ironing.
There is an amber
light ashing on
the handle of the
iron.
The iron leaves a
shine or an imprint
on the garment.
The iron makes a
lot of noise.
You have an ironing board
cover that is not designed
to cope with the high steam
rate of the appliance.
You have used the steam
boost function too often
within a short period.
You have not closed the
water tank lid properly.
You have not insert
the Quick Calc Release
collector properly back
to the appliance (specic
types only).
You have put a chemical
into the water tank.
You have used the steam
boost function too often
within a short period.
You are ironing before the
iron gets ready
Hard water with impurities
or chemicals has formed
akes inside the soleplate.
The Calc-Clean reminder
light is activated. This is
to remind you to perform
Calc-Clean.
The surface to be ironed
was uneven, for instance
because you ironed over
a seam or a fold in the
garment.
There is no water in the
appliance.
Put an extra layer of felt material under
the ironing board cover to prevent
condensation on the ironing board.
You can buy felt in a fabric shop.
Continue ironing in horizontal position and
wait a while before you use the steam boost
function again.
Press the lid until you hear a ‘click’.
Stop ironing and let the iron cools down for at
least 1 hour. Take out the Quick Calc Release
collector. Insert it back into the appliance and
ensure the collector is in-line with the surface
of the appliance. Push down the lever (“click”).
If the Quick Calc release tray is damaged,
contact a consumer care center in your country
(see the world wide guarantee leaet for
contact details).
Rinse the water tank and do not put any
perfume or chemicals into the water tank.
Continue ironing in horizontal position and
wait a while before you use the steam boost
function again.
Wait until the iron is ready (the light on the
display panel stops ashing).
Perform Quick Calc Release (specic types
only) or Calc-Clean (specic types only).
See chapter “Cleaning and maintenance”.
Perform Quick Calc Release (specic types
only) or Calc-Clean (specic types only).
See chapter “Cleaning and maintenance”.
The iron is safe to use on all ironable garments.
The shine or imprint is not permanent and
disappears when you wash the garment. Avoid
ironing over seams or folds. You can also place
a cotton cloth over the area to be ironed to
avoid imprints.
Fill the water in the water tank.
Loading...
+ 15 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.