Philips FC9130 Service Manual

Specialist Vacuum cleaner

FC9130
/A

Philips Domestic Appliances and Personal Care

Service Manual

PRODUCT INFORMATION

- This product meets the requirements regarding
interference suppression on radio and TV.

- After the product has been repaired, it should function
properly and has to meet the safety requirements as
officially laid down at this moment.

TECHNICAL INFORMATION

- Colour /A : Titanium silver

- Maximum air displacement : 38 l/sec.

- Maximum vacuum water column : 310 cm

- Power consumption (IEC) 230 V : 1800 W

- Duststorage capacity : 3 L

- Type number dustbag : FC8021

- Cord length (depends on version) : 7 metres

- Filter system : Paper dustbag
: Exhaust AFS air filter
: Motor inlet filter

- Dimensions of cleaner : 460 x 315 x 270 mm

- Dimensions of packaging : 595 x 395 x 295 mm

- Net weight : 5.88 kg

- Gross weight : 9.135 kg

- Motor : Infra red
remote controlled

OPTIONAL (accessories)

- FC8021 S-bags

- FC8022 Clinic S-bags

- FC8023 Anti - odour S-bags

- FC8025 S-fresh perfume

- FC8030 AFS-filter

- FC8031 HEPA Air Filter

- FC8034 Upgrate kit Active Carbon Filter

- FC8042 Polishing nozzle

- FC8043 Turbo brush nozzle

DISASSEMBLY- AND RE-ASSEMBLY ADVISE

- Open the appliance, first remove

the exhaust filter grille (item 20),
and then remove the 2 screws -

C of the switch control panel

(item 15).

- Undo and remove the 9 screws -

C in the upper housing (item 8).

You will require a screwdriver with
a 14.5 cm-long shank for this.
Screwdriver 4322 009 08490 for
T15 can be used.

- The component configuration shown in the exploded view
may differ in case of specific versions. The components are
distinguished by means of code numbers.

- When the repair is finished, check whether all functions of
the appliance work properly.

- To disassemble the cord winder, use TORX screwdriver no.
T10, which is one of a set consisting of T20; T15; T10; T9;
T8; T7 and T6 (code number 4822 395 50145).

C 2x

C 9x

Published by Philips Domestic Appliances and Personal Care Printed in the Netherlands © Copyright reserved Subject to modification

03/03

REPAIR INSTRUCTION

FC9130 /A

- Item 4, cotton dustbag, is used in countries in which paper

dustbags are not available.

- If the reel half spring unit is replaced, shaft A must be lubri­cated with silicone grease. Do not apply any silicone grease
to or spill any grease on terminals (43) or conductors (42).

- Item 40 is provided with a long cord-winder spring, but
both long and short cords can be used in combination with
this spring. (L = 9.3 m)

- Depending on the original cord, the spare cord must be
shortened to the length of the original cord.

- The cord winder spring must be tensioned to the maximum
level and then be rewound approx. 1.5 turn

- Item 13, air valve, opens to cool the motor if the air
displacement is too low or if the airflow is blocked.

- To adjust the telescopic tube (item 59) to the required
length, push the adjustment collar in the direction of the
arrow while sliding the top section of the telescopic tube
into or out of the lower section.

- If the function of the electronic control unit (item 12) is
not required, the Triac must be short-circuited in the
manner shown in the circuit diagram.

- When the vacuum cleaner is used to suck up fine dust the
pores of the dustbag may become clogged, causing the
passage of air through the dustbag to become obstructed.
As a result, the dustbag-full indicator will indicate that the
dustbag needs to be replaced, eventhough the dustbag is not
full at all.

- To replace the side brushes (item 63a), the nozzle must be
switched as used on hard floors.

- With the infrared remote control, the suction power can be
set to one of 5 different suction power settings. When the
appliance is switched on, it always starts running at the
highest suction power, even without the hose being
connected. Use LR03 batteries for the remote control
(alkaline batteries are recommended).

= changed

- Due to introduction of a new switch (item 11) 0320

onwards, which is not interchangable with the old switch
soldered on the PCB (item 12).

- The switch lever assy (item 11a) is also modified.

To recognize the switches:

Old New

∅ 13 mm

∅ 10 mm

To replace the knobs:

2

1

New spares are:

11 Switch soldered version - 4322 006 50600
11a Switch lever assy - 4322 009 08980
parts of 15 Switch and Cord winder knob - 4322 009 09000

ELECTRICAL DIAGRAM

IR­TRANSMITTER

IR

MOTOR
POWER

MODULE

Black

Black

Blue

Brown

M

CORD WINDER

Triac

Short-circuit

2-6