Philips FC9112/09, FC9110/09, FC9110/01, FC9108/09, FC9108/01 User Manual [zh]

...
0 (0)
R
e
a
c
h
&
C
e
a
n
T
M
R
e
a
c
h
&
C
l
e
a
n
T
M
13cm
Specialist
Specialist
FC9108
2
3
12
3
4
25
10
9
7
8
6
24
11
13
12 14
26
22
23
20
21
21
5
16
15
17
18 19
4
ENGLISH 6
15
5
FC9108
Important
Only use Philips s-bag` double-layer paper dustbags (type
FC8021).
Check if the dustbag has been placed correctly.Never use the vacuum cleaner to suck up water or any other
liquid. Never suck up ashes until they are cold.
When the vacuum cleaner is used to suck up fine dust, the pores
of the dustbag may become clogged, causing the passage of air through the dustbag to become obstructed.As a result, the dustbag-full indicator will indicate that the dustbag needs to be replaced, even though the dustbag is not full at all.
Never use the appliance without the Motor Protection Filter.This
could damage the motor and shorten the life of the appliance.
General description
1 On/Off button 2 Cordwinder button 3 Opening dustcover 4 Clean comfort cassette 5 Hinging handle 6 Opening filtercover 7 Swivel opening 8 Front grip 9 Dustbag full indicator 10 Power Slide 11 Rearwheels 12 Castor wheel 13 Park position 14 Storage position 15 Accessory bridge 16 Small nozzle 17 Crevice tool 18 Small brush 19 Button coupling 20 Reach & Clean nozzle 21 Brush indications 22 Turning switch mechanism hard/soft floors 23 Parking ridge 24 Plug 25 Triple motor inlet filter 26 Type plate
ENGLISH6
Connecting accessories
Hose
C
1 To connect the hose, push it firmly into the appliance (you will
hear a click).
C
2 To disconnect the hose, push the buttons on the swivel and
pull the hose out of the appliance.
Tube
Button coupling
C
Connect the tube to the handgrip by pressing the spring-loaded
lock button on the handgrip and inserting the handgrip into the tube. Fit the spring-loaded lock button into the opening in the tube ("click").
C
To disconnect the tube from the handgrip, press the spring-loaded
lock button and pull the handgrip out of the tube.
Use the same method to connect and disconnect the other
accessories.
ENGLISH 7
Telescopic tube
1 Connect the tube to the handgrip ("click").
C
2 Adjust the tube to the length you find most comfortable during
vacuum cleaning.
Reach & Clean nozzle
C
The Reach & Clean nozzle can be used on either carpets or hard
floors.The nozzle can be put in 4 different positions, allowing you to also vacuum clean hard-to-reach places in an easy way.The nozzle can be turned 360 degrees clockwise as well as anti­clockwise.
C
To adjust the nozzle to the type of floor and the area to be
cleaned, put your foot on the indicated positions and then turn the tube until the nozzle is in the required position.
C
1 With the nozzle positioned breadthwise and the brush strip
folded out, you can clean large hard floor areas.Turn the nozzle until the brush strip pops out of the nozzle housing and the nozzle is positioned breadthwise.
C
2 With the nozzle positioned lengthwise and the brush strip
folded out, you can vacuum clean small hard floor areas.Turn the nozzle 90 degrees clockwise until it is positioned lengthwise with the brush strip still folded out of the nozzle housing.
ENGLISH8
Loading...
+ 17 hidden pages