Philips FC9128 Service Manual

Specialist Vacuum cleaner

FC9128 /A

Philips Domestic Appliances and Personal Care

Service Manual

PRODUCT INFORMATION

- This product meets the requirements regarding interference suppression on radio and TV.

- After the product has been repaired, it should function properly and has to meet the safety requirements as officially laid down at this moment.

TECHNICAL INFORMATION

- Colour /A : Crushed berry

- Maximum air displacement : 38 l/sec.

- Maximum vacuum water column : 310 cm

- Power consumption (IEC) 230 V : 1800 W

- Duststorage capacity : 3 L

- Type number dustbag : FC8021

- Cord length (depends on version) : 7 metres

- Filter system : Paper dustbag : Exhaust AFS air filter : Motor inlet filter

- Dimensions of cleaner : 460 x 315 x 270 mm

- Dimensions of packaging : 595 x 395 x 295 mm

- Net weight : 5.88 kg

- Gross weight : 9.135 kg

OPTIONAL (accessories)

- FC8021 S-bags

- FC8022 Clinic S-bags

- FC8023 Anti - odour S-bags

- FC8025 S-fresh perfume

- FC8030 AFS-filter

- FC8031 HEPA Air Filter

- FC8034 Upgrate kit Active Carbon Filter

- FC8042 Polishing nozzle

- FC8043 Turbo brush nozzle

DISASSEMBLY- AND RE-ASSEMBLY ADVISE

- Open the appliance, first remove

the exhaust filter grille (item 20), and then remove the 2 screws -

C of the switch control panel

(item 15).

- Undo and remove the 9 screws -

C in the upper housing (item 8).

You will require a screwdriver with a 14.5 cm-long shank for this. Screwdriver 4322 009 08490 for T15 can be used.

- The component configuration shown in the exploded view may differ in case of specific versions. The components are distinguished by means of code numbers.

- When the repair is finished, check whether all functions of the appliance work properly.

- To disassemble the cord winder, use TORX screwdriver no. T10, which is one of a set consisting of T20; T15; T10; T9; T8; T7 and T6 (code number 4822 395 50145).

C 2x

C 9x

Published by Philips Domestic Appliances and Personal Care Printed in the Netherlands © Copyright reserved Subject to modification

03/03

REPAIR INSTRUCTION

FC9128 /A

- Item 4, cotton dustbag, is used in countries in which paper

dustbags are not available.

- If the reel half spring unit is replaced, shaft A must be lubricated with silicone grease. Do not apply any silicone grease to or spill any grease on terminals (43) or conductors (42).

- Item 40 is provided with a long cord-winder spring, but both long and short cords can be used in combination with this spring. (L = 9.3 m)

- Depending on the original cord, the spare cord must be shortened to the length of the original cord.

- The cord winder spring must be tensioned to the maximum level and then be rewound approx. 1.5 turn

- Item 13, air valve, opens to cool the motor if the air displacement is too low or if the airflow is blocked.

- To adjust the telescopic tube (item 59) to the required length, push the adjustment collar in the direction of the arrow while sliding the top section of the telescopic tube into or out of the lower section.

- If the function of the electronic control unit (item 12) is not required, the Triac must be short-circuited in the manner shown in the circuit diagram.

- When the vacuum cleaner is used to suck up fine dust the pores of the dustbag may become clogged, causing the passage of air through the dustbag to become obstructed. As a result, the dustbag-full indicator will indicate that the dustbag needs to be replaced, eventhough the dustbag is not full at all.

- To replace the side brushes (item 63a), the nozzle must be switched as used on hard floors.

- Due to introduction of a new switch (item 11) 0320

onwards, which is not interchangable with the old switch soldered on the PCB (item 12).

- The switch lever assy (item 11a) is also modified.

To recognize the switches:

Old New

∅ 13 mm

To replace the knobs:

∅ 10 mm

= changed

ELECTRICAL DIAGRAM

MOTOR POWER

MODULE

Black

Blue

Brown

CORD WINDER

New spares are:

11 Switch soldered version - 4322 006 50600 11a Switch lever assy - 4322 009 08980 parts of 15 Switch and Cord winder knob - 4322 009 09000

Triac

Short-circuit

2-7

PARTS LIST

FC9128 /A

Pos Service code Description

4322 009 08830

4322 003 22130

4322 003 22180

8838 021 00000 4322 004 93290

4322 003 18300

4322 001 73310

4322 005 12550

4322 003 22080

4322 003 22150

8838 033 01010

4822 458 10461

4322 006 21480

4322 006 50600

11a

4322 009 08420

4322 009 08980

4322 006 22560

13a

4322 005 12200

13b

4322 005 12210

4322 003 22110

4322 009 08180

4322 003 22050

4322 003 22120

4322 000 37450

4322 005 14690

4322 009 08850

20a

4322 005 15150

4322 004 92910

4322 001 73280

4322 003 18000

4322 000 37420

4322 000 37430

4322 003 22100

4322 003 18910

4322 003 22070

4322 001 73300

4322 003 18040

4322 003 18010

4322 003 18020

not available

Dust cover Crushed berry Dust cover ﬂ int grey Dustbag holder ﬂ int grey S-paper dustbags FC8021 Cotton dustbag

Cordwinder lever Sealing rim Dustbag detector Upper housing ﬂ int grey Clamp upper/lower housing ﬂ . grey

Active coal ﬁ lter Grill coal ﬁ lter Switch soldered version

Switch sold. vers. 0320 onwards

Switch lever assy

Switch lever assy 0320 onwards

PCB slide turn 230 V (standard) Dustbag full indicator Air valve Handle ﬂ int grey

Panel slide Crushed berry Lower housing ﬂ int grey Handle lock ﬂ int grey Silencer 4 wall Caster assy (standard) grey

Exhaust grille Crushed berry Cilinder assy Electr.static ﬁ lter FC8030 Filter sealing S-class sealing

Silencer 1 wall Silencer 2 bottom Cord outlet ﬂ int grey Rear wheel lock red Receipt. housing A.C.

Rear wheel ﬂ int grey Motor buffer back Inlet sealing Motor cap top ANS disc

Pos Service code Description

4322 001 73290

4322 009 06430

4322 000 37440

4322 003 18030

4322 009 07940

4322 001 72360

4322 009 07950

4322 009 07970

4322 006 01440 4322 006 01760

4322 006 01680

4322 006 01720

4322 006 01410

4322 006 01670

4322 006 01460

4322 003 18850

4322 005 12720

4322 007 16000

4322 004 22570

4322 003 18870

4322 005 12530

4322 004 22510

4322 001 99120

4322 007 45550

4322 004 22560

4322 004 23080

63a

4322 009 08950

63b

4322 003 21950

9965 000 03349

4822 358 10205

4822 479 20201

4322 004 22960

4322 004 22640

5322 390 20011

4322 002 82550

2522 200 02018

Motor bufferring front Motor A1451 - 230 V (standard) Silencer 3 ans Motor cap bottom Reel half spring unit (L = 9m)

Brake tyre Reel half contact unit Contact ring plate Argentina L = 9.3 m Australia L = 9.3 m

Taiwan L = 6.3 m U.K. / H.K. L = 9.3 m Euro 4.8 mm pins L = 9.3 m Swiss L = 9.3 m Italy L = 9.3 m

C-bend B1 C-bend B1 hose sw assy Leaf spring assy Plumeau assy Crevice nozzle

Acc. bridge assy Telesc. tube st. silver complete Tube bush Tube spring Small nozzle

Tri active nozzle Brush replacement set Brush switch knob Coupl. piece (standard) Drive belt

Brush assy Turbo nozzle Cat and dog brush

Silicon grease for shaft Screw 3.5 x 12 T10 Screw 3.5 x 18 T15

= changed

3-7

+ 4 hidden pages