Philips FC9110AB Service Manual

Specialist Vacuum cleaner

FC9110
/A
/B

Philips Domestic Appliances and Personal Care

Service Manual

PRODUCT INFORMATION

- This product meets the requirements regarding
interference suppression on radio and TV.

- After the product has been repaired, it should function
properly and has to meet the safety requirements as
officially laid down at this moment.

TECHNICAL INFORMATION

- Colour /A : Crushed berry
Version /B : 2000 W logo

- Maximum air displacement : 37 l/sec.

- Maximum vacuum water column : 310 cm

- Power consumption (IEC) 230 V : 1500 W

- Duststorage capacity : 3 L

- Type number dustbag : FC8021

- Cord length (depends on version) : 7 metres

- Filter system : Paper dustbag
: Exhaust AFS air filter
: Active carbon motor
inlet filter

- Dimensions of cleaner : 460 x 315 x 270 mm

- Dimensions of packaging : 595 x 395 x 295 mm

- Net weight : 5.88 kg

- Gross weight : 9.135 kg

OPTIONAL (accessories)

- FC8021 S-bags

- FC8030 AFS-filter

- FC8031 HEPA Air Filter

- FC8033 Active Carbon Filter

- FC8034 Upgrate kit Active Carbon Filter

- HR6988 Turbo brush nozzle

- HR8040 Polishing nozzle

DISASSEMBLY- AND RE-ASSEMBLY ADVISE

- Open the appliance, first remove

the exhaust filter grille (item 20),
and then remove the 2 screws -

C of the switch control panel

(item 15).

- Undo and remove the 9 screws -

C in the upper housing (item 8).

You will require a screwdriver
with a 14.5 cm-long shank for
this. Depending on the version
screwdriver 9965 000 08332 for
cross head or onwards 0234
screwdriver 4322 009 08490 for T15 can be used.

- The component configuration shown in the exploded view
may differ in case of specific versions. The components are
distinguished by means of code numbers.

- When the repair is finished, check whether all functions of
the appliance work properly.

- To disassemble the cord winder, use TORX screwdriver no.
T10, which is one of a set consisting of T20; T15; T10; T9;
T8; T7 and T6 (code number 4822 395 50145).

C 2x

C 9x

Published by Philips Domestic Appliances and Personal Care Printed in the Netherlands © Copyright reserved Subject to modification

04/02

REPAIR INSTRUCTION

FC9110 /A /B

- Item 4, cotton dustbag, is used in countries in which paper

dustbags are not available.

- If the reel half spring unit is replaced, shaft A must be
lubricated with silicone grease. Do not apply any silicone
grease to or spill any grease on terminals (43) or conductors
(42).

- Item 40 is provided with a long cord-winder spring, but
both long and short cords can be used in combination with
this spring. (L = 9.3 m)

- Depending on the original cord, the spare cord must be
shortened to the length of the original cord.

- The cord winder spring must be tensioned to the maximum
level and then be rewound approx. 1.5 turn

- Item 13, air valve, opens to cool the motor if the air
displacement is too low or if the airflow is blocked.

- To adjust the telescopic tube (item 59) to the required
length, push the adjustment collar in the direction of the
arrow while sliding the top section of the telescopic tube
into or out of the lower section.

- If the function of the electronic control unit (item 12) is
not required, the Triac must be short-circuited in the
manner shown in the circuit diagram.

- When the vacuum cleaner is used to suck up fine dust the
pores of the dustbag may become clogged, causing the
passage of air through the dustbag to become obstructed.
As a result, the dustbag-full indicator will indicate that the
dustbag needs to be replaced, eventhough the dustbag is not
full at all.

- Item 72, sealing ring must be replaced if appliance

whistles.

- Due to introduction of a new switch (item 11) 0320

onwards, which is not interchangable with the old switch
soldered on the PCB (item 12).

- The switch lever assy (item 11a) is also modified.

To recognize the switches:

Old New

∅ 13 mm

To replace the knobs:

∅ 10 mm

2

1

ELECTRICAL DIAGRAM

MOTOR
POWER

MODULE

Black

Black

Blue

Brown

M

CORD WINDER

New spares are:

11 Switch soldered version - 4322 006 50600
11a Switch lever assy - 4322 009 08980
parts of 15 Switch and Cord winder knob - 4322 009 09000

Triac

Short-circuit

= changed

2-7

PARTS LIST

FC9110 /A /B

Pos Service code Description

1

4322 009 08110

2

4322 003 18280

3

4322 003 18150

4

4822 480 10113
4322 004 93290

5

4322 003 18300

6

4322 001 73310

7

4322 005 12550

8

4322 003 18050

8a

4322 003 20410

9

4822 480 20145

10

4322 003 10950

11

4322 006 21480
4322 006 50600

11a

4322 009 08420

4322 009 08980

12

4322 006 22560

13a

4322 005 12200

13b

4322 005 12210

14

4322 003 18090

15

4322 009 08180

16

4322 003 17890

17

4322 003 18100

18

4322 000 37450

19

4322 005 12180

20

4322 009 08250

21

4322 000 37460

22

4322 004 92910

23

4322 001 73280

24

4322 003 18000

25

4322 000 37420

26

4322 000 37430

27

4322 003 18070

28

4322 003 18910

29

4322 003 11990

30

4322 003 17950

31

4322 001 73300

32

4322 003 18040

33

4322 003 18010

34

4322 003 18020

Dust cover Crushed berry
Dust cover lock grey
Dustbag holder
S-paper dustbags FC8021
Cotton dustbag

Cordwinder lever
Sealing rim
Dustbag detector
Upper housing l.grey
Clamp upper/lower housing

Active carbon fi lter FC8033
Grill
Switch soldered version
Switch sold. vers. 0320 onwards
Switch lever assy

Switch lever assy 0320 onwards
PCB slide turn 230V
Dustbag full indicator
Air valve
Handle l.grey

Panel slide Crushed berry
Lower housing l.grey
Handle lock
Silencer 4 wall
Caster assy l.grey

Exhaust grille Crushed berry
Exhaust diffusor
Electr.static fi lter FC8030
Filter sealing
S-class sealing

Silencer 1 wall
Silencer 2 bottom
Cord outlet l.grey
Rear wheel lock red
Receipt. housing A.C.

Rear wheel l.grey
Motor buffer back
Inlet sealing
Motor cap top
ANS disc

Pos Service code Description

35

4322 001 73290

36

4322 009 06430

37

4322 000 37440

38

4322 003 18030

40

4322 009 07940

41

4322 001 72360

42

4322 009 07950

43

4322 009 07970

44

4322 006 01440
4322 006 01760

45

4322 006 01680

46

4322 006 01720

47

4322 006 01410

48

4322 006 01670

49

4322 006 01460

50

4322 003 18850

51

4322 005 12720

54

4322 007 16000

55

4322 004 22570

56

4322 003 18870

57

4322 005 12530

59

4322 004 22520

60

4322 001 99120

61

4322 007 45550

62

4322 004 22560

63

4322 004 22490

67

9965 000 03349

68

4822 358 10205

69

4822 479 20201

70

4322 004 22580

71

4322 004 22640

72

4322 003 19110

A

5322 390 20011

B

4322 002 82550

C

4322 002 82080

= changed

Motor bufferring front
Motor A 1441 230V
Silencer 3 ans
Motor cap bottom
Reel half spring unit (L = 9m)

Brake tyre
Reel half contact unit
Contact ring plate
Argentina L = 9.3 m
Australia L = 9.3 m

Taiwan L = 6.3 m
U.K. / H.K. L = 9.3 m
Euro 4.8 mm pins L = 9.3 m
Swiss L = 9.3 m
Italy L = 9.3 m

C-bend B1
C-bend B1 hose sw assy
Leaf spring assy
Plumeau assy
Crevice nozzle

Acc. bridge assy
Telesc. tube act. coupling silver
Tube bush
Tube spring
Small nozzle

R&C nozzle standard l.grey
Coupl. piece (standard)
Drive belt
Brush assy
Turbo nozzle act. coupling

Cat and dog brush assy

Sealing ring

Silicon grease for shaft
Screw 3.5 x 12 T10
Screw 3.5 x 19

3-7