Philips FC9106AB Service Manual

Service Manual

Philips Domestic Appliances and Personal Care

Published by Philips Domestic Appliances and Personal Care Printed in the Netherlands © Copyright reserved Subject to modification

Specialist Vacuum cleaner

FC9106

04/02

PRODUCT INFORMATION

- This product meets the requirements regarding

interference suppression on radio and TV.

- After the product has been repaired, it should function

properly and has to meet the safety requirements as

officially laid down at this moment.

TECHNICAL INFORMATION

- Colour /A : Cherry wood

Version /B : 2000 W logo

- Maximum air displacement : 37 l/sec.

- Maximum vacuum water column : 310 cm

- Power consumption (IEC) 230 V : 1500 W

- Duststorage capacity : 3 L

- Type number dustbag : FC8021

- Cord length (depends on version) : 7 metres

- Filter system : Paper dustbag

: Exhaust AFS air filter

: Motor inlet filter

- Dimensions of cleaner : 460 x 315 x 270 mm

- Dimensions of packaging : 595 x 395 x 295 mm

- Net weight : 5.88 kg

- Gross weight : 9.135 kg

OPTIONAL (accessories)

- FC8021 S-bags

- FC8030 AFS-filter

- FC8031 HEPA Air Filter

- FC8034 Upgrate kit Active Carbon Filter

- HR6988 Turbo brush nozzle

- HR8040 Polishing nozzle

DISASSEMBLY- AND RE-ASSEMBLY ADVISE

- Open the appliance, first remove

the exhaust filter grille (item 20),

and then remove the 2 screws -

C of the switch control panel

(item 15).

- Undo and remove the 9 screws -

C in the upper housing (item 8).

You will require a screwdriver

with a 14.5 cm-long shank for

this. Depending on the version

screwdriver 9965 000 08332 for

cross head or onwards 0234

screwdriver 4322 009 08490 for T15 can be used.

- The component configuration shown in the exploded view

may differ in case of specific versions. The components are

distinguished by means of code numbers.

- When the repair is finished, check whether all functions of

the appliance work properly.

- To disassemble the cord winder, use TORX screwdriver no.

T10, which is one of a set consisting of T20; T15; T10; T9;

T8; T7 and T6 (code number 4822 395 50145).

C 2x

C 9x

FC9106 /A /B

REPAIR INSTRUCTION

- Item 4, cotton dustbag, is used in countries in which paper

dustbags are not available.

- If the reel half spring unit is replaced, shaft A must be

lubricated with silicone grease. Do not apply any silicone

grease to or spill any grease on terminals (43) or conductors

(42).

- Item 40 is provided with a long cord-winder spring, but

both long and short cords can be used in combination with

this spring. (L = 9.3 m)

- Depending on the original cord, the spare cord must be

shortened to the length of the original cord.

- The cord winder spring must be tensioned to the maximum

level and then be rewound approx. 1.5 turn

- Item 13, air valve, opens to cool the motor if the air

displacement is too low or if the airflow is blocked.

- To adjust the telescopic tube (item 59) to the required

length, push the adjustment collar in the direction of the

arrow while sliding the top section of the telescopic tube

into or out of the lower section.

- If the function of the electronic control unit (item 12) is

not required, the Triac must be short-circuited in the

manner shown in the circuit diagram.

- When the vacuum cleaner is used to suck up fine dust the

pores of the dustbag may become clogged, causing the

passage of air through the dustbag to become obstructed.

As a result, the dustbag-full indicator will indicate that the

dustbag needs to be replaced, eventhough the dustbag is not

full at all.

- Item 72, sealing ring must be replaced if appliance

whistles.

- Due to introduction of a new switch (item 11) 0320

onwards, which is not interchangable with the old switch

soldered on the PCB (item 12).

- The switch lever assy (item 11a) is also modified.

To recognize the switches:

Old New

∅ 13 mm

∅ 10 mm

To replace the knobs:

New spares are:

11 Switch soldered version - 4322 006 50600

11a Switch lever assy - 4322 009 08980

parts of 15 Switch and Cord winder knob - 4322 009 09000

ELECTRICAL DIAGRAM

MOTOR

POWER

MODULE

Black

Blue

Brown

CORD WINDER

Short-circuit

Triac

2-6

= changed

+ 4 hidden pages