Pelco CM9760-CDU-T Specsheet
PRODUCT SPECIFICATION
CM9760-CDU-T (FRONT)
CM9760-CDU-T (BACK)
analog systems and controls
CM9760-CDU-T Code Distribution Unit
16-CHANNEL TRANSMIT-ONLY DISTRIBUTOR
Product Features
• Two 8-Position, RJ-45 Parallel Connectors Provide an Input from a
Controller and an Output for an Additional Daisy-Chained CDU Unit
• Sixteen 3-Position Screw Terminal Connectors Used to Output
16 RS-422 Transmit-Only Code Lines
• Allows for “Star” Type Wiring of PTZ Data Lines
• Standard 100-240 VAC, 50/60 Hz Line Input (Autoranging)
• Provides 16 Driver Outputs
The CM9760-CDU-T code distribution unit is a 16-channel RS-422
transmit-only (two data wires and ground) data distribution unit. It
can be used with any system that uses RS-422 serial
communications. The CDU is used to install pan/tilt and dome
receivers in a “star,” or “home run,” configuration.
The unit is rack/wall mountable and is only 6 inches (15.2 cm) deep.
In addition to the 16 lines available for output with one unit, eight
CDUs may be daisy-chained. This allows 128 receivers (that support
128 address settings) to be connected on a single SERCOM port.
1.75
(4.45)
(15.24)
6.00
9760
17.40 (44.20)
CM9760-CDU-T
Code Distribution Unit
Made In USA
The remote devices can be located as far as 4,000 feet (1,219 m)
away from the controller, depending on the physical parameters of
the connection.
The unit is ideal for use on larger switching systems where it
becomes desirable to “home run” the RS-422 data lines for
controlling pan/tilt or dome receivers.
19.00 (48.26)
NOTE: VALUES IN PARENTHESES ARE CENTIMETERS;
ALL OTHERS ARE INCHES.
International Standards
Organization Registered Firm;
ISO 9001 Quality System
C1940 / REVISED 11-1-10
TECHNICAL SPECIFICATIONS
Pelco, the Pelco logo, and other tradema rks associated with Pelco products referred
to in this publication are trademarks of Pelco, Inc. or its affiliates. All other
product names and services are the p roperty of their respective companies.
Product specifications and availability are subject to change without notice.
©Copyright 2010, Pelco, Inc. All rights reserved.
MODEL
CM9760-CDU-T Code distribution unit
ELECTRICAL
Input Voltage 100-240 VAC, 50/60 Hz, autoranging; or
independent external source
10-24 VAC/VDC
Input Current 100 mA
Data Ports
Input One RS-422, RJ-45 female connector
Output One RS-422, RJ-45 female connector
Drive Lines Sixteen 3-position screw terminals with
mating plugs
Indicators One power LED (green)
One data LED (red)
MECHANICAL
Connectors
Power AC power cord input, 3-wire, 18 AWG
RS-422 Two RJ-45, female
RS-422 Breakout Ports Sixteen 3-pin headers with mating plug;
connectors can accept 14-28 AWG
GENERAL
Dimensions
Base Only 1.75" H x 17.40" W x 6.00" D
(4.45 x 44.20 x 15.24 cm)
With Rack Ears 1.75" H x 19.00" W x 6.00" D (1 RU)
(4.45 x 48.26 x 15.24 cm)
Mounting Fits 19-inch EIA-standard rack
Operating Temperature 32° to 122°F (0° to 50°C)
Unit Weight 4.2 lb (1.91 kg)
Shipping Weight 9 lb (4.09 kg)
CERTIFICATIONS/RATINGS
• CE, Class B
• FCC, Class B
• UL/cUL Listed
•C-Tick
NOTE: OTHER RS-422 PROTOCOL DEVICES
INCLUDE THE CM6800,
CM9760-DMR, AND KBD300A (DIRECT MODE).
CM9760-CDU-T
TYPICAL CONFIGURATION
RS-422 PROTOCOL
CM9700-CC1
CM9760-CDU-T
Pelco, Inc. Worldwide Headquarters:
3500 Pelco Way, Clovis, California 93612-5699 USA
USA & Canada Tel: (800) 289-9100 • FAX: (800) 289-9150
International Tel: +1 (559) 292-1981 • FAX: +1 (559) 348-1120
www.pelco.com
Loading...