Pelco C1932M, CC4620 User Manual 2

CC3320/CC4620 Series

Color Cameras

Installation/

Operation Manual

C1932M (8/99)

Pelco • 300 W. Pontiac Way, Clovis • CA 93612-5699 USA • Pelco Online @ http://www.pelco.com
In North America and Canada: Tel [phone] or FAX [phone] • DataFAX [phone]
International Customers: Tel [phone] or FAX [phone] • DataFAX (1-559) 292-0435

CC3320 and CC4620 Cameras Installation Instructions

INTRODUCTION

These instructions cover Pelcos CC3320 and CC4620 Series cameras. Read all of these instructions.
Use them to install your camera and have them available for its lifetime. Refer to Table A for the
camera models and their features. All cameras in the range are fitted with a direct drive (DD) lens
connector, have adjustable back focus and accept C and CS lenses.

TABLE A

Option

CC4620-3

CC4620-2X

CC3320-3

CC3320-2X

Color
Resolution (TVL)
Sensitivity (lux @ f1.2)
CCD Sensor size

480 480 330 330

1.01.00.90.9

1/3“ 1/3“ 1/3“ 1/3“

Sony HyperHAD CCD
Adjustable Gamma (0.45 and 1.0)
Automatic Gain Control (AGC)
AGC on/off
Backlight Compensation (BLC)
BLC on/off
Manual Shutters
Flickerless
Electronic Iris (EI)
EI on/off
4 White Balance modes*
Auto Iris connection
Line lock with phase adjust (AC only)

Page 2

Dimensions

4.82 (L) x 2.57 (W) x 2.34 (H) inches
(12.25 x 6.55 x 5.95 cm)

Supply

11 - 40 VDC or 14 - 30 VAC, 50/60Hz
230 VAC + 10% -15% 50Hz

* 4 Modes = Auto Tracing (ATW), Indoor, Outdoor and Fluorescent

Installation Instructions CC3320 and CC4620 Cameras

PRODUCT SAFETY

 Ensure installation and servicing is carried out by qualified personnel.
 Isolate from the supply circuit before any servicing.
 Installation method and materials must be capable of supporting four times the total

weight of the unit.

 Power supply cords must be connected as defined in national electrical codes of

practice for Class 1 earth protected equipment.

 Low voltage cameras must be connected as defined in national electrical codes of

practice for Class 2 protection of double or reinforced insulation.

 Safety critical components must only be replaced with recommended parts.

The maximum load on the rear (auto-iris) connector must not exceed 50 mA.
The maximum load on the direct drive connector must not exceed 25 mA.

REGULATORY NOTICES

Federal Communications Commission Part 15 - Digital devices
This Device complies with part 15 of the FCC rules. Operation is subject to the following two

conditions:
(1)this device may not cause harmful interference, and
(2) this device must accept any interference that may cause undesired operation.

CERTIFICATIONS

This product meets the requirements of the following standards:

Electromagnetic Compatibility

EN55022: 1995 limits and methods of measurement of radio disturbance characteristics of information
technology

EN50082-1: 1992 Generic immunity standard

Comprising:

IEC 1000-4-2:1995 Electrostatic discharge
IEC 1000-4-3:1995 Radiated electromagnetic fields
IEC 1000-4-6: Immunity to conducted disturbances, induced by radio-frequency fields
IEC 1000-4-4:1995 Fast transient bursts

Safety

EN 60950: 1992 Safety of information technology equipment, including electrical business equipment

DECLARATIONS

The manufacturer declares that the equipment supplied with this manual is compliant with the EMC
directive 89/336 EEC and the low voltage directive 73/23 EEC and CE marked accordingly.

Page 3