Pelco CC3751H-2 User Manual

INSTALLATION/OPERATION

CC3751H-2

DSP Color Camera

English Español

C1988M-B-ML (3/05)

Important Safeguards and Warnings

Prior to installation and use of this product, the following WARNINGS should be observed.

1. Installation and servicing should be done only by qualiﬁed service and installation personnel.

2. Installation shall be done in accordance with all local and national electrical and mechanical codes utilizing only approved materials.

3. Use only installation methods and materials capable of supporting four times the maximum speciﬁed load.

4. Use only UL listed class 2 power supply.

5. To prevent ﬁre or shock hazard, do not expose this appliance to rain or moisture.

2 C1988M-B-ML (3/05)

ENGLISH

Regulatory Notices

This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Description

The CC3751H-2 is a high resolution, color video camera with a 1/3-inch CCD imager. The camera features a digital slow shutter (DSS) mode, a direct drive/auto iris lens connector, adjustable back focus, backlight compensation, automatic gain control, and an adjustable C/CS lens mount.

Models

CC3751H-2 High resolution, 480 TV lines, SuperHAD™ CCD, minimum illumination of 0.1 lux at

f1.2 and 40 IRE, NTSC format

C1988M-B-ML (3/05) 3

ENGLISH

Camera Layout

BACK FOCUS ADJUSTMENT LOCKING SCREW

BACK FOCUS ADJUSTMENT RING

BNC VIDEO CONNECTOR

LENS CONNECTOR

MOUNT ADAPTER

PHASE ADJUSTMENT

LENS LEVEL ADJUSTMENT

LED

DIP SWITCHES (COVER REMOVED)

POWER CONNECTOR

COSMETIC TRIM RING

20156

NOTE: The cosmetic trim ring conceals the LED light for more discreet surveillance operations. The trim ring also hides the power connectors and protects the DIP switches.

Figure 1.

Camera Layout

Installation

LENS MOUNTING

The camera can use a ﬁxed iris, manual iris or auto iris lens. The camera is factory set for a CS-mount lens, but is easily adjusted for a C-mount lens.

C-Mount Lens Only -

1. installing the C-mount lens (refer to the section on

2. Remove the cosmetic trim ring from the back of the camera (refer to Figure 1). Set the lens mode selector switch on the side of the camera to AIV (auto iris video drive lens) or AID (auto iris DC drive lens). Refer to the type of lens used.

3. Screw the lens onto the lens mount. Be careful to prevent dust from entering the space between the lens and the CCD element. If necessary, use clean, compressed air to remove any foreign matter.

4. Thread the lens cable through the cosmetic trim ring.

5. Connect the auto iris lens to the four-pin connector located on the side of the camera. Pin connections for the iris drive connector are as follows:

Rotate the back focus adjustment fully counterclockwise before

Switch Settings

Back Focus Adjustment

section. Switch setting is determined by the

PIN DC (AID) AUTO IRIS LENS VIDEO (AIV) AUTO IRIS LENS

1 Control coil negative (-) Lens positive supply 2 Control coil positive (+) Not used 3 Drive coil positive (+) Video drive signal 4 Drive coil negative (-) Ground

Figure 2.

4 C1988M-B-ML (3/05)

Lens Connections

ENGLISH

CAMERA MOUNTING

Use a standard 1/4-20 screw (provided) with a maximum thread length of 3/8-inch (10 mm) for top or bottom camera mounting. The mount adapter may be ﬁtted to the top or bottom of the camera. The camera is shipped with the mount adapter located on the top of the camera.

To change the mount adapter position:



Remove the four screws from the mount adapter located on the top of the camera.



Remove the trim cover from the bottom of the camera by prying it loose. Place the trim cover on the top of the camera where the mount adapter was removed. Press into place.



Install the mount adapter to the bottom of the camera. Secure with the four screws removed in step 1.

Figure 3.

Camera Mounting

POWER AND VIDEO CONNECTIONS

The camera is designed to operate from a 12 VDC or 24 VAC power supply. The power supply connections are shown in Figure 1. The LED on the back panel of the camera indicates that power is connected. Use only a Class 2 isolated power supply. See

CLASS 2

ISOLATED

POWER

SUPPLY

24 VAC

Figure 4.

To connect the camera power and video:

1. Remove the cosmetic trim ring from the camera (refer to Figure 1). Thread cabling through the rear cover.

2. Connect the power cable to the two-pin power connector on the back of the camera using the terminal block connector (provided). Refer to Table A for the recommend wire gauge and wiring distances.

3. Connect a video cable to the SIGNAL OUT connector (BNC) on the back of the camera. Refer to Table B for the type of video coaxial cable to use.

4. Reattach the cosmetic trim ring to the back of the camera.

Power Supply Connections

Speciﬁcations

for power consumption.

ISOLATED

20155

CLASS 2

POWER

SUPPLY

12 VDC

C1988M-B-ML (3/05) 5

ENGLISH

AC operation only -

side of the transformer to the same terminal on all cameras, and connect the other side of the transformer to the remaining terminal on all cameras. Failure to connect all of the cameras the same way will cause the cameras to be out of phase with each other and may produce a vertical roll when switching between cameras.

If you are wiring more than one camera to the same transformer, connect one

Table A.

The following are the recommended maximum distances for 24 VAC applications and are calculated with a 10-percent voltage drop. (Ten percent is generally the maximum allowable voltage drop for AC-powered devices.)

Total 20 18 16 14 12 10

vA (0.5 mm2) (1.0 mm2) (1.5 mm2) (2.5 mm2) (4.0 mm2) (6.0 mm2) 10 283 451 716 1142 1811 2880

(86) (137) (218) (348) (551) (877)

Example:

require a minimum wire gauge of 20 AWG.

NOTE:

parentheses are meters.

A camera that requires 10 vA and is installed 283 feet (86 m) from the transformer would

Wire gauges are standard AWG or metric sizes. Distances are calculated in feet; values in

Recommended Wire Gauge and Wiring Distances

Wire Gauge

Table B.

* Minimum cable requirements:

Video Coaxial Cable Requirements

Cable Type* Maximum Distance

RG59/U 750 ft (229 m)

RG6/U 1,000 ft (305 m)

RG11/U 1,500 ft (457 m)

75 ohms impedance All-copper center conductor All-copper braided shield with 95% braid coverage

6 C1988M-B-ML (3/05)

ENGLISH

Lens Setup and Focus Procedures

Video Drive Auto Iris Lens

Set the lens mode selector switch to AIV. Switch the ESC and AGC OFF. Refer to the lens instructions and adjust the lens for the optimum picture (video output level of 1V peak-to-peak). To focus, fully open the iris by covering the lens with a suitable neutral density (ND*) ﬁlter. If the viewed scene is

6.5 feet (2 m) away or farther, set the lens focus to inﬁnity (far). Use the back focus adjustment ring (refer to the and set the lens focus as required.

Direct Drive (DC) Auto Iris Lens

Set the lens mode selector switch to AID. Switch the ESC ON. Use an appropriate screwdriver to turn the lens level potentiometer (refer to Figure 1) fully clockwise. Next, slowly adjust the potentiometer counterclockwise until the optimum picture is obtained (video output level of 1V peak-to-peak). To focus, fully open the iris by covering the lens with a suitable neutral density (ND*) ﬁlter. Select the scene to be viewed. If the viewed scene is 6.5 feet (2 m) away or farther, set the lens focus to inﬁnity (far). Use the back focus adjustment ring (refer to the selected scene. Remove the ND ﬁlter and set the lens focus as required.

Fixed Lens

To focus, set the lens focus to inﬁnity and view an image greater than 6.5 feet (2 m) away. Focus the image with the back focus adjustment ring (refer to the focus as required.

Manual Iris Lens

To focus, open the iris fully and set the lens focus to inﬁnity. View an image greater than 6.5 feet (2 m) away. Focus the image with the back focus adjustment ring (refer to the section). Adjust the lens focus, and set the iris for the best picture quality. The largest aperture gives the best light sensitivity, the smallest aperture the greatest depth of ﬁeld.

Zoom Lens

Set the lens focus to inﬁnity (far) and fully open the iris by covering the lens with a suitable neutral density (ND*) ﬁlter. Zoom out to the widest ﬁeld of vision and view a distant object. Adjust the back focus adjustment ring until the object is in focus (refer to the Next, zoom fully in and adjust the lens focus until the object is again focused. Repeat these steps until the full zoom range may be viewed with the minimum loss of focus.

* NOTE:

Back Focus Adjustment

section) and focus on the selected scene. Remove the ND ﬁlter

For best results, outdoors, use an ND3 ﬁlter.

Back Focus Adjustment

section) to focus on the

section). Set the lens

Back Focus Adjustment

section).

Back Focus Adjustment

The back focus adjustment is located at the front of the camera and is accessible from either side of the case.

To adjust the back focus:

1. Loosen the two back focus locking

screws (one on each side).

2. Turn the back focus ring until the object is in focus.

3. When the back focus adjustment is satisfactory, tighten the locking screws.

BACK FOCUS

DJUSTMENT

RING

Do not over tighten the locking screw or force the back focus adjustment ring.

C1988M-B-ML (3/05) 7

ENGLISH

Figure 5.

Back Focus Adjustment

BACK FOCUS ADJUSTMENT

WIS

LOCKING SCRE

Switch Settings

NOTE: White indicates

switch setting.



BLC

- Back Light Compensation

OFF

(Default setting) - Disables the BLC mode.

BLC -

Enables the BLC mode. If a bright backlight is present, the objects in the picture may

PHASE LEVEL OFF

OFF OFF AW1

NOR

OFF OFF OFF

Figure 6.

AIV INT

DIP Switch Default Settings

BLC OPT ESC AW2 AID LL SHP LC DS1 DS2

appear dark or as a silhouette. BLC enhances objects in the center of the picture.



OPT -

Optimal Video

OFF

(Default setting)

OPT -

Boosts the video by 3 dB.



ESC -

Electronic Shutter Control

OFF -

Disables the ESC mode.

ESC

(Default setting) - Enables the ESC mode. The ESC function automatically changes the sensitivity of the camera by varying the electronic shutter speed according to the amount of incident light. Electronic shutter speed range is 1/60 to 1/100,000.



AW1/AW2 -

AW1

Automatic White Balance

(Default setting) - Automatically processes the viewed image to retain color balance over

a wide color temperature range.

AW2 -

Processes the viewed image to retain color balance in a restricted color temperature

range.



AIV/AID

- Auto Iris Lens Mode Selector

The switch setting is determined by the type of lens used:

AIV -

Video controlled Auto Iris lens.

AID

(Default setting) - DC controlled Auto Iris lens.



INT/LL -

Internal/Line Lock

Line Lock

(LL) (Default setting) - Locks the vertical frame to the power supply frequency.

Eliminates vertical roll caused by multiple cameras connected to the same switching device.



NOR/SHP -

Internal -

NOR SHP -

Locks the vertical frame to the internal oscillator. Use with DC or unstable AC.

Sharpness

(Default setting) - Sets the camera to normal sharpness mode.

Enables the Sharpness mode. Enhances picture detail by increasing the aperture gain of

the camera, sharpening the edges in the picture.

8 C1988M-B-ML (3/05)

ENGLISH

+ 16 hidden pages