PANJIT PG600A, PG600B, PG600D, PG600G, PG600J Datasheet
...
PG600A THRU PG600K
FEATURE
S
MECHANICAL DATA
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTIC
S
PG600APG600BPG600DPG600GPG600JPG600
K
m
P
P60
0
GLASS PASSIVATED JUNCTION PLASTIC RECTIFIER
VOLTAGE - 50 to 800 Volts CURRENT - 6.0 Amperes
l
High surge current capability
l
Plastic package has Underwriters Laboratory
Flammability Classification 94V-O Utilizing
Flame Retardant Epoxy Molding Compound
l
Glass passivated junction in P600 package
l
High current operation 6.0 Amperes @ TA=75
l
Exceeds environmental standards of MIL-S-19500/228
Case: Molded plastic, P600
Terminals: axial leads, solderable per MIL-STD-202,
Method 208
Polarity: Color band denotes cathode
Mounting Position: Any
Weight: 0.07 ounce, 2.1 gram
¢J
*@ TA=25 ¢J unless otherwise specified. Single phase, half-wave,60 Hz, resistive or inductive load.
**All values except Maximum RMS Voltage are registered JEDEC parameters.
UNITS
Maximum Recurrent Peak Reverse Voltage 50 100 200 400 600 800 V
Maximum RMS Voltage 35 70 140 280 420 560 V
Maximum DC Blocking Voltage 50 100 200 400 600 800 V
Maximum Average Forward
Rectified Current at TA=75 ¢J
Maximum Overload Surge Current at 1 cycle (NOTE 1) 300 A
Maximum Forward Voltage at 6.0 ADC 1.0 V
Maximum Full Load Reverse Current Full Cycle
Average at 25 ¢J
Maximum DC Reverse Current at Rated
DC Blocking Voltage and 100 ¢J
Typical Junction capacitance (Note 2) CJ 150.0
Typical Thermal Resistance (Note 3) R £KJA
Typical Thermal Resistance (Note 3) R£KJL
Operating Temperature Range -55 to +150 ¢J
Storage Temperature Range -55 to +150 ¢J
NOTES:
1. Peak forward surge current, per 8.3ms single half-sine-wave superimposed on rated load(JECED method)
2. Measured at 1 MHZ and applied reverse voltage of 4.0 volts
3. Thermal resistance from junction to ambient and from junction to lead at 0.375"(9.5mm) lead length P.C.B.
mounted with 1.1×1.1(30×30mm) copper pads
6.0 A
10 £g
0.3
20.0
4.0
¢J/W
¢J
ADC
ADC
A
F
/W
RATING AND CHARACTERISTIC CURVES
AMBIENT TEMPERATURE,
¢J
PERCENT OF RATED PEAK REVERSE VOLTAG
E
0.1
t, PULSE DURATION. Sec
.
MEDIA
N
5%10%
MAXIMUM FORWARD VOLTAGE-VFM(VpK)
TJ = 25
P
A
T
M
PG600A THRU PG600K
100
10
CURRENT, £g A
1
INSTANTANEOUS REVERSE
25 ¢J
8.0
6.0
4.0
(10)-AMP
2.0
VERAGE FORWARD CURRENT
0
50 75 100
. 5" LOAD LENGTH
125
150
175
200
0.1
0
20 40
60 80
100 120 140
Fig. 1-TYPICAL REVERSE CHARACTERISTICS
100
10
Fig. 2-FORWARD DERATING CURVE
10
1.0
0.1
¢J/W
1
RANSIENT THERMAL IMPEDANCE,
0.01 0.1 1 10 100
AXIMUM FORWARD CURRENT-1FM(ApK)
.01
0.5 0.6
0.7 0.8 1.1 1.3 1.5 1.7
Fig. 3-TYPICAL TRANSIENT THERMAL IMPEDANCE Fig. 4-TYPICAL FORWARD CHARACTERISTICS
500
400
300
AMPERES
EAK FORWARD SURGE CURRENT
200
100
0
8.3ms SINGLE HALE SINE-WAVE
¢J
1
10 100
NUMBER OF CYCLES AT 60Hz
Fig. 5-PEAK FORWARD SURGE CURRENT
Loading...