Panasonic WV-CW474S, WV-CW474F User Manual

1. Do not attempt to disassemble the camera.

To prevent electric shock, do not remove screws or covers.
There are no user-serviceable parts inside. Ask qualified service personnel for servic­ing.

2. Handle the camera with care.

Do not abuse the camera. Avoid striking, shaking, etc. The camera could be damaged
by improper handling or storage.

3. Do not expose the camera to rain or moisture, not try to operate it in wet areas.

If the camera becomes wet, turn the power off immediately and ask qualified service
personnel for servicing. Moisture may damage the camera and also cause electric
shock.

4. Do not use strong or abrasive detergents when cleaning the camera body.

Use a dry cloth to clean the camera when dirty. When the dirt is hard to remove, use a
mild detergent and wipe gently. Then wipe off the remaining detergent with a dry cloth.

5. Clean the CCD faceplate with care.

Do not clean the CCD with strong or abrasive detergents. Use lens tissue or a cotton
tipped applicator and ethanol.

6. Never face the camera towards the sun.

Do not aim the camera at bright objects. Whether the camera is in use or not, never
aim it at the sun or other extremely bright objects. Otherwise, blooming or smear may
be caused.

7. Do not operate the camera beyond the specified temperature, humidity or power
source ratings.

Use the camera at temperatures within –10 °C to +50 °C (14 °F - 122 °F), and humidity
below 90 %. The input power source is 24 V AC.

8. Turn the circuit breaker off which supplies the camera with the power when
abnormal conditions are encountered.

PRECAUTIONS

Before attempting to connect or operate this product,

please read these instructions carefully and save this manual for future use.

The exclamation point within
an equilateral triangle is intend­ed to alert the user to the pres­ence of important operating
and maintenance (servicing)
instructions in the literature
accompanying the appliance.

The lightning flash with arrow­head symbol, within an equilat­eral triangle, is intended to
alert the user to the presence
of uninsulated "dangerous volt­age" within the product's enclo­sure that may be of sufficient
magnitude to constitute a risk
of electric shock to persons.

The serial number of this product may be found
on the top of the unit.
You should note the serial number of this unit
in the space provided and retain this instruction
as a permanent record of your purchase to aid
identification in the event of theft.

Model No.
Serial No.

SA 1966

SA 1965

N1101-1121 V8QA5931BN Printed in Japan

N 19

Panasonic's WV-CW474F/CW474S series color digital camera introduces a new level of high
picture quality and high resolution through the use of a 1/3-inch interline transfer CCD image
sensor having 768 horizontal pixels (picture elements), and digital signal processing LSIs.
This model offers cutting-edge technology for advanced video surveillance.

PREF ACE

Caution:

To prevent fire or electric shock hazard, use a UL listed cable (VW-1, style 1007) for
the 24 V AC Input Cable.

Color CCTV Cameras

Operating Instructions

WARNING:

To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE. REFER SER-

VICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC

SHOCK DO NOT OPEN

NOTE: This equipment has been tested and
found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful interfer­ence when the equipment is operated in a
commercial environment. This equipment gen­erates, uses, and can radiate radio frequency
energy and, if not installed and used in accor­dance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential
area is likely to cause harmful interference in
which case the user will be required to correct
the interference at his own expense.

FCC Caution: To assure continued compli­ance, (example - use only shielded interface
cables when connecting to computer or
peripheral devices). Any changes or modifica­tions not expressly approved by the party
responsible for compliance could void the
user’s authority to operate this equipment.

For U.S.A

Model No. WV-CW474F

WV-CW474S

1. The following functions are built in.

(1) Auto Light Control (ALC)
(2) The SUPER-D2 function eliminates interference by strong background lighting

which makes the camera picture dark, such as a spotlight.

Dynamic range of 46 dB (Typ)
(3) Internal, Line-Locked, Multiplexed Vertical Drive (VD2) Sync
(4) Auto/Manual White Balance Function
(5) Electronic Shutter Function

2. Signal-to-noise ratio of 50 dB (Equivalent to AGC Off)

3. Minimum illumination of 2.4 lx (0.24 footcandle) (WIDE) (Color mode)
Minimum illumination of 0.3 lx (0.03 footcandle) (WIDE) (Black-and-white mode)
Minimum illumination of 0.8 lx (0.08 footcandle) (WIDE) with the WV-CW1C optional
dome cover (Color mode)
Minimum illumination of 0.1 lx (0.01 footcandle) (WIDE) with the WV-CW1C optional
dome cover (Black-and-white )

4. 480 lines of horizontal resolution (Color mode)
570 lines of horizontal resolution (Black-and-white mode)

5. High quality picture:

(a) 2H type vertical enhancer for greater picture sharpness

(b) Chroma averaging circuit for better color signal-to-noise ratio

(c) Minimum of aliasing on fine objects

(d) Expanded dynamic range by use of knee circuit

(e) Highlight aperture correction for greater picture detail of bright objects

6. Selectable electronic sensitivity enhancing modes including AUTO, MANUAL and OFF

7. Built-in Digital Motion Detector

8. Auto black-and-white mode enables the camera to switch between color and black-and­white picture in response to Light input.

9. Electronic zoom function magnifies a scene 2-fold and changes the angle of view.

FEATURES

MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS

q Panning table

Adjusts the panning angle of the camera.

w Pan lock screw

Fixes the panning position.

e Tilting lock screw

Fixes the tilting position.

r AZIMUTH (Angle adjuster)

Shoots in a straight-angle field of view when aiming at an object in a slanting direction
even if the tilt angle has been set.

t Zoom lock lever

Fixes the zoom position.

y Focus lock lever

Fixes the focus position.

u LEFT button (I) (L)

Moves the cursor to the left, selects the mode and adjusts some levels.

q

w

e

r

y

t

L

D

U

OWN

R

IGHT

P

EFT

u
i
o

!0

!1

SET

!4
!3
!2

!5

!6

!7

LOW

HIGH

OFF

AUTO1

SHARP

SOFT

OFFONINT

LL

Cautions:

1. Connect to 24 V AC (19.5 V-28 V) class 2 power supply only. Make sure to connect
the grounding lead to the GND terminal when the power is supplied from a 24 V AC
power source.

2. To prevent fire or electric shock hazard, use a UL listed cable (VW-1, style 1007) for
the Input Terminal.

i RIGHT button (I) (R)

Moves the cursor to the right, selects the mode and adjusts some levels.

o UP button (I) (U)

Moves the cursor upward and selects items in the CAM SET UP menu.

!0 DOWN button (I) (D)

Moves the cursor downward and selects items in the CAM SET UP menu.

!1 SET button (I) (S)

Activates an item selected in the CAM SET UP menu.

!2 BW AUTO1 LEVEL switch (SW5)

Selects the illuminance level in LOW or HIGH mode for B/W. The factory default setting
is HIGH.

!3 BW switch (SW4)

Switches to AUTO1 between color and black-and-white picture in response to light
input. The factory default setting is OFF.

!4 AP gain switch (SW3)

Selects the aperture gain level to SHARP or SOFT. The factory default setting is SHARP.

!5 UPSIDE DOWN switch (SW2)

Turns the picture upside down by selecting ON. The factory default setting is OFF.

!6 Sync switch (SW1)

Switches internal sync (INT) mode or line-lock (LL) mode. The factory default setting is
INT.

!7 Monitor output Jack (3.5 Diam. mini jack)

Connects the LCD monitor and such devices with 3.5 diam. 2-pole L-type plug for
checking images.

!8 Power cable

!9 Video output cable with BNC connector

Connects with the video connector of the monitor.

@0 Dome cover

@1 Camera mounting bracket

The WV-CW474S is supplied with a mounting bracket for ceiling installation.

!8
!9

@0

@1

1. CAMERA SETUP MENU

This camera utilizes an on-screen user setup menu.

• Opening the Setup Menu

Press and hold down I(S) for 2 seconds
or more.

The CAM SET UP menu appears on the
monitor as shown at right.
Check the current settings on the menu.

Refer to the following sections for a detailed description of menu items. If you decide not to
make any changes after checking the current settings, move the cursor to END in the bot­tom line, and press I(S) to close the setup menu.

Note: If no button is pressed for 6 minutes while a setup menu is being displayed on the

monitor screen, it is automatically closed and the mode returns to the normal camera
picture.

2. SETUP OPERATION

This camera utilizes an on-screen user setup menu (CAM SET UP). To set items on the CAM
SET UP menu, use the following buttons on the side panel.

Left Button (I) (L): Moves the cursor to the left. Use this button to select or adjust the

parameters of the selected item. The parameter changes each
time this button is pressed.

Right Button (I) (R): Moves the cursor to the right. Use this button to select or adjust the

parameters of the selected item. The parameter changes each
time this button is pressed.

Up Button (I) (U): Moves the cursor upwards. Use this button to select an item or

adjust the parameters.

Down Button (I) (D): Moves the cursor downwards. Use this button to select an item or

adjust the parameters.

Set Button (I) (S): Executes selections and displays a submenu for an item with the

mark.

• To reset the parameter to the factory default setting, move the cursor to the parameter
to be reset and press I(L) and I(R) simultaneously.

• To return to the previous menu or page, move the cursor to RET and press I(S).

• To close the setup menu, move the cursor to END and press I(S).

• All Reset Operation

All Reset allows you to reset all setup menu items to the factory default settings if you are
unsure about the correct settings. Proceed as follows:

(1) Make sure that the CAM SET UP menu is not displayed (a camera picture is displayed).
(2) While pressing both I(L) and I(R), press I(S) for a few seconds. The message

ALL RESET momentarily appears on the monitor screen.
This resets all adjustments and parameters to the factory default settings.

• Editing the CAM SET UP Menu

Important Notice:

When SET UP DISABLE appears in the bottom line of the CAM SET UP menu, you can­not change the currently active settings. This is to prevent accidental changing of the
settings.

To edit the CAM SET UP menu (change
settings), press I(U) and I(D) or
I(L) and I(R) to move the cursor to
SET UP DISABLE in the bottom line.

Press I(S). SETUP DISABLE changes
to SETUP ENABLE. Move the cursor to
DIP SW. Press I(S). DIP SW changes
to MENU. Then move the cursor to the
item(s) you want to change.

Notes:

• When DIP SW is selected for CAM SET UP menu, five modes can be set with the DIP
switches.

• To operate the camera functions with the system controller, select MENU in the CAM
SET UP menu.

Important Notice:

When the setup menu is closed after changing the parameters in the menu, the new
values are stored in the EEPROM (Electrically Erasable and Programmable Read-Only
Memory). These values remain valid until new values are stored, even if the power of
the camera is off.

SETUP

** CAM SET UP **
CAMERA ID OFF
ALC ALC
SHUTTER --­AGC ON(DNR-H)
SENS UP OFF
SYNC INT
WHITE BAL ATW1
MOTION DET OFF

DIP SW
END SET UP DISABLE

↵↵↵

↵

** CAM SET UP **
CAMERA ID OFF
ALC ALC
SHUTTER --­AGC ON(DNR-H)
SENS UP OFF
SYNC INT
WHITE BAL ATW1
MOTION DET OFF

DIP SW
END SET UP DISABLE

↵↵↵

** CAM SET UP **
CAMERA ID OFF
ALC ALC
SHUTTER --­AGC ON(DNR-H)
SENS UP OFF
SYNC INT
WHITE BAL ATW1
MOTION DET OFF

MENU
END SET UP ENABLE

↵↵↵

1. Camera Identification (CAMERA ID) Setting

You can use the camera identification (CAMERA ID) to assign a name to the camera. The
camera ID consists of up to 16 alphanumeric characters. The camera ID display can be
switched on or off on the monitor screen.

To edit the CAMERA ID

1. Move the cursor to CAMERA ID.
The factory default setting is OFF.

2. Press I(S). The CAMERA ID menu
appears. The cursor on the letter “0” is
highlighted.

3. Move the cursor to the character you want
to edit by pressing I(L) / I(R) /
I(U) / I(D).

4. After selecting the character, press
I(S). The selected character appears
in the editing area. (The pointer in the
editing area moves to the right automati­cally at this moment.)

5. Repeat the steps above until all characters are edited.

To enter a blank space in the CAMERA ID

Move the cursor to SPACE and press I(S).

To replace a specific character in the CAMERA ID

1. Move the cursor to the editing area by pressing I(D).

2. Move the pointer to the character to be replaced by pressing I(L) or I(R). Then
move the cursor to the character area and select a new character.

3. Press I(S) to determine the CAMERA ID.

To erase all characters in the editing area

Move the cursor to RESET and press I(S). All characters in the editing area disappear.

To determine the display position of the CAMERA ID

1. Move the cursor to POSI, and press
I(S). The display at right appears and
the CAMERA ID is highlighted.

2. Move the CAMERA ID to the desired posi­tion by pressing I(L) / I(R) / I(U) /
I(D).

3. Press I(S) to fix the position of the
CAMERA ID. The mode returns to the pre­vious CAMERA ID menu.

Notes:

• The CAMERA ID stops at the edges of the monitor screen.

• The CAMERA ID moves faster if any of I(L) / I(R) / I(U) / I(D) is kept
pressed for a second or more.

2. Light Control Setting (ALC)

2-1. ALC Mode with SUPER-D2 ON

Super Dynamic2 Function (SUPER-D2)

The important object in a scene is usually placed in the center of the monitor screen. In the
SUPER-D2 mode, more photometric weight is given to the center of the screen (where the
important object is located) than to the edge of the screen (where a bright backlight would
most likely be located). The SUPER-D2 function eliminates interference by strong back­ground lighting which makes the camera picture dark, such as a spotlight.

1. Move the cursor to ALC and press I(S).
The ALC CONT menu appears.

2. Move the cursor to SUPER-D2 and select
ON.

3. If you want to adjust the video output
level, move the "I" cursor for LEVEL. Adjust
to the desired level by pressing I(L) or
I(R).

(To be continued reverse page)

SETTING PROCEDURES

Highlighted

Character Cursor

Pointer

Character
Area

Command
Editing

Area

CAMERA ID menu

0123456789
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
().,'":;&#!?=
+-*/%$

SPACE
POSI RET END RESET

................

WV-CW474

** ALC CONT **
BACK LIGHT COMP
SUPER-D2 ON

LEVEL ...I.....

- +
RET END

2-2. ALC Mode with SUPER-D2 OFF

1. Move the cursor to SUPER-D2 and
select OFF. The MASK SET appears on
the menu.

2. Move the cursor to MASK SET and
press I(S). The 48 mask areas
appear on the monitor screen. The cur­sor is blinking in the upper left corner
of the screen.

3. Move the cursor to the area where
backlight is bright and press I(S) to
mask that area. The mask turns to
white. (When the cursor is moved on
an area that has already been masked,
the mask and cursor start blinking.)

4. Repeat step 3 to mask the desired
area. To cancel masking, move the
cursor to that area and press I(S).

5. After masking is completed, press
I(S) for 2 seconds or more. The ALC
CONT menu appears.

6. If you want to change the video output

6. Synchronization Setting (SYNC)

You can select internal sync (INT) mode, line-lock (LL) mode or the VD2 signal (multiplexed
vertical drive signal) mode.

Important Notices:

1. The priority for the sync modes is as follows:
(1) Multiplexed Vertical Drive (VD2) (Highest priority)
(2) Line-lock (LL)
(3) Internal Sync (INT) (Lowest priority)

2. The line-lock mode has a submenu for line-lock vertical phase adjustment. If the cam-

era installation is relocated, check the vertical phase adjustment again since the AC
line phase may be different.

6-1. Line-lock Sync Mode (LL)

1. Move the cursor to SYNC and select

LL.
Note: The settings in this menu can be

made only when the multiplexed
vertical drive signal (VD2) is not
supplied to the camera.

2. After confirming that the cursor is on

LL, press I(S). The vertical phase
adjustment menu appears on the moni­tor screen.

3. Supply the video output signal of the camera to be adjusted and the reference camera

video output signal to a dual-trace oscilloscope.

4. Set the oscilloscope to the vertical rate and expand the vertical sync portion on the

oscilloscope.

5. Move the cursor to COARSE. The cur-

sor is highlighted.

6. Press I(L) or I(R) to match the

vertical phase for both video output
signals as closely as possible.
(COARSE adjustment can be incre­mented in 16 steps by 22.5 degrees by
pressing I(L) or I(R).)
Note: After the sixteenth step, the

adjustment returns to the first step.

7. Move the cursor to FINE.

8. Press I(L) or I(R) to match the vertical phase for both video output signals as

closely as possible.
(FINE adjustment can be made by up to 22.5 degrees by pressing I(L) or I(R).)

Notes:

• When the “I” cursor reaches the “+” end, it jumps back to “–”. At the same time,
COARSE is incremented by one step to enable a continuous adjustment. The
reverse takes place when the “I” cursor reaches the “–” end.

• When I(L) or I(R) is kept pressed for a second or more, the “I” cursor moves
faster.

• To reset COARSE and FINE to the values preset at the factory, press I(L) and
I(R) simultaneously. COARSE and FINE adjustments are preset at the factory to

zero-crossing of the AC line phase.

• If the AC line contains noise (spike noise, etc.), the stability of the vertical phase of
the camera video output signal may be disturbed.

7. White Balance Setting (WHITE BAL)

7-1. Auto-Tracing White Balance Mode (ATW)

You can select one of three modes for white balance adjustment as follows:
The factory default setting is ATW1.

• ATW1 (Auto-Tracing White Balance 1)

Move the cursor to WHITE BAL and select ATW1.
In this mode, the color temperature is monitored continuously and thereby white bal­ance is automatically set. The color temperature range for the proper white balance is
approximately 2 600 - 6 000K. Proper
white balance may not be obtained
under the following conditions:

1. The color temperature is out of
the 2 600 - 6 000K range.

2. When the scene contains mostly
high color temperature objects,
such as a blue sky or sunset.

3. When the scene is dim.

In these cases, select the AWC
mode.

• ATW2 (Auto-Tracing White Balance 2)

Auto-tracing white balance in sodium light mode (ATW2)
When that you select ATW2 for sodium light, white balance is set automatically (no
operation needed).
Note: ATW1 and ATW2 do not appear for WHITE BAL on the system controller setup

menu.

• Automatic White Balance Control Mode (AWC)

In this mode, accurate white balance is obtained within a color temperature range of
approximately 2 300-10 000K.

1. Move the cursor to WHITE BAL and
select AWC → PUSH SW.

2. Press I(S) to start the white balance
setup. The PUSH SW is highlighted to
indicate that the white balance is being
set.

3. When the white balance setting is completed, the PUSH SW returns to normal display.
Note: If white balance is not set, the PUSH SW is being highlighted.

4. When you want to adjust the white bal­ance manually, press I(R) to select
AWC and press I(S). The AWC
menu appears on the monitor screen.
(When ATW is selected, pressing
I(S) displays the ATW menu.)

Highlighted

** SYNC **
V PHASE
COARSE 1(1--16)

FINE I........

- +

RET END

1 (1 - - 16): 0 degrees
2 (1 - - 16): 22.5 degrees

16 (1 - - 16): 337.5 degrees

** CAM SET UP **
CAMERA ID OFF
ALC ALC
SHUTTER --­AGC ON(DNR-H)
SENS UP OFF
SYNC INT
WHITE BAL ATW1
MOTION DET OFF

MENU
END SET UP ENABLE

↵↵↵

** CAM SET UP **
CAMERA ID OFF
ALC ALC
SHUTTER --­AGC ON(DNR-H)
SENS UP OFF
SYNC INT
WHITE BAL AWC
MOTION DET OFF

MENU
END SET UP ENABLE

↵↵

→

PUSH SW

** AWC **

R ....I....

- +

B ....I....

- +
MASK SET

RET END

↵

9-6 Electronic Zoom (EL-ZOOM)

1. Move the cursor to EL-ZOOM.

2. Select ON or OFF using I(L) or I(R).
The factory default setting is OFF.

ON: x2 electronic zoom is available with the ZOOM switch on the controller.
OFF: The electronic zoom function is disabled.

3. While the cursor is on EL-ZOOM, press
I(S). The EL-ZOOM setting menu
appears.

4. Move the cursor to PUSH SET for ZOOM
and press I(S) to display the ZOOM set­ting menu.

5. Press I(U) or I(D) to zoom in or out
the image.

6. Move the cursor to PUSH SET for PAN/TILT
and press I(S). The PAN/TILT setting
menu appears.

7. Press I(U) or I(D) I(L) or I(R) to
change the angular field of view.

8. To return to the EL-ZOOM setting menu,
press I(S).

9-7 BW

This function lets you switch from color to black-and-white picture automatically in low light
conditions such as at night.

1. Move the cursor to BW.

2. Select AUTO1, AUTO2, ON or OFF using I(L) or I(R).
The factory default setting is OFF.
AUTO1: The camera selects black and white mode if the picture is dark, or color mode

if the picture is bright enough.

AUTO2: Applying AUTO1 may cause malfunction when using a source of near-infrared

light at night because the illuminance changes significantly when switching
between the color picture and a black-and-white picture. This can be prevented by
using the AUTO2 setting to detect the type of light source.

Notes:

• Because the type of light source is detected based on information received
from the CCD image pickup element, an object that is constantly moving or
has the same color as its background may not always be properly recognized.
When choosing the AUTO2 mode, make sure to use a light source having a
wavelength of 800 nm or more.

• The object may be out of focus when using a source of near-infrared light than
using the visible light.

ON: Black-and-white mode enabled.
OFF: Color mode enabled.

3. Select AUTO1 or AUTO2 using I(L) or
I(R).

4. Press I(S).
The AUTO1 or AUTO2 menu appears on
the monitor screen.

5. Move the “I” cursor to LEVEL to select the
illuminance level using I(L) or I(R).
The factory default setting is HIGH.
LOW: Color picture switches to black-and-

white picture at approx.2 lx.

HIGH: Color picture switches to black-and-white picture at approx.5 lx.

6. Move the “I” cursor for DURATION TIME to set the switching time using I(L) or
I(R).
The following switching times are available:

10s--30s--60s--300s

(S) (L)

9-8 BURST (BW)

1. Move the cursor to BURST (BW).

2. Select ON or OFF using I(L) or I(R).

ON: The burst signal is supplied along with the black-and-white composite video signal.
OFF: The burst signal is not output.

The factory default setting is ON.

Notes:

• We recommend that you usually select ON.

• When the camera is used to synchronize the system for external sync, select

ON to prevent a malfunction.

To reset to the factory settings (CAMERA RESET)

1. Move the cursor to CAMERA RESET. The PUSH SW is highlighted.

2. While holding down I(L) and I(R), press I(S) for 2 seconds or more. The cam­era is reset to the factory settings.

** EL-ZOOM **
PAN/TILT →PUSH SET

ZOOM →PUSH SET
U TILT D/L PAN R

RET END

** EL-ZOOM **
PAN/TILT →PUSH SET

ZOOM →PUSH SET
U ZOOM D

RET END

** BW AUTO1 **
LEVEL HIGH

DURATION TIME .I..
S L

RET END

Pick-up Device: 768 (H) x 494 (V) pixels, Interline Transfer CCD
Scanning Area: 4.8 (H) x 3.6 (V) mm (Equivalent to scanning area of

1/3” pick-up tube)

Scanning: 525 lines/60 fields/30 frames

Horizontal: 15.734 kHz
Vertical: 59.94 Hz

Synchronization: Internal, Line-locked or Multiplexed vertical drive (VD2)

Sync selectable
Video Output: 1.0 V[p-p] NTSC composite 75 Ω/BNC connector
Horizontal Resolution: 480 lines (C/L), 570 lines (B/W)
Signal-to-Noise Ratio: 50 dB (Equivalent to AGC Off, weight On, AP On)
Dynamic Range: 46 dB (Typ)
Minimum Illumination: 2.4 lx (0.24 footcandle) (WIDE) (C/L),

0.3 lx (0.03 footcandle) (WIDE) (B/W)

When the optional WV-CW1C dome cover is installed.

0.8 lx (0.08 footcandle) (WIDE) (C/L),

0.1 lx (0.01 footcandle) (WIDE) (B/W)

Gain Control: ON (DNR-H), ON (DNR-L) or OFF (SET UP MENU)

selectable
White Balance: ATW1, ATW2 or AWC (SET UP MENU) selectable
Aperture: Set Variable (SET UP MENU)
Super Dynamic2: ON or OFF (SET UP MENU) selectable
Electronic Shutter Speed: OFF, 1/100, 1/250, 1/500, 1/1 000,1/2 000,

1/4 000, 1/10 000 s selectable
Lens

Focal length: 3.8 mm - 8 mm
Maximum aperture ratio: 1:1.4 (Wide), 1:1.8 (Tele)
Angular field of view: Horizontal: 35.6 ˚ - 73.6 ˚

Vertical: 26.6 ˚ - 53.4 ˚

Focusing range: 1.2 m - ∞ (3.9 ft - ∞)
Ambient Operating Temperature: –10 °C - +50 °C (14 °F - 122 °F)
Ambient Operating Humidity: Less than 90 %
Power Source and

Power Consumption: 24 V AC 60 Hz, 4.6 W
Dimensions (without lens): WV-CW474F: 133 mm (H) x 152.5 mm (D)

5-1/4” (H) x 6” (D)

WV-CW474S: 136.5 mm (H) x 160 mm (D)

5-3/8” (H) x 6-5/16” (D)

Weights: WV-CW474F: 1.0 kg (2.2 lbs.)

WV-CW474S: 1.4 kg (3.1 lbs.)

Weights and dimensions indicated are approximate.
Specifications are subject to change without notice.

SPECIFICATIONS

OPTIONAL ACCESSORIES

STANDARD ACCESSORIES

Tamperproof screw bit ......................................................................1 pc.

Camera mounting bracket (supplied with only WV-CW474S)............ 1 pc.

Camera mounting screw (with a plastic washer) .............................. 4 pcs.

(supplied with only WV-CW474S)

WV-CW1C Dome Cover
WV-Q112 Camera mounting bracket (for WV-CW474F)

2001 © Matsushita Communication Industrial Co., Ltd.

Panasonic Security and Digital Imaging Company
A Division of Matsushita Electric Corporation of America

Executive Office: One Panasonic Way 3E-7, Secaucus, New Jersey 07094
Regional Offices:

Northeast: One Panasonic Way, Secaucus, NJ 07094 [phone]
Southern: 1225 Northbrook Parkway, Suite 1-160, Suwanee, GA 30024 [phone]
Midwest: 1707 North Randall Road, Elgin, IL 60123 [phone]
Western: 6550 Katella Ave., Cypress, CA 90630 [phone]

Panasonic Canada Inc.

5770 Ambler Drive, Mississauga,
Ontario, L4W 2T3 Canada [phone]

Panasonic Sales Company
Division of Matsushita Electric of Puerto Rico Inc.

Ave. 65 de Infanteria. Km. 9.5
San Gabriel Industrial Park, Carolina,
Puerto Rico 00985 [phone]