Panasonic WJ-FS416, WJ-FS316, WJ-FS309, WJ-FS409 User Manual
Video Multiplexer WJ-FS
309
FS
O
N
P
O
W
E
R
O
F
F
O
N
P
O
W
E
R
O
F
F
Video Multiplexer WJ-FS
409
FS
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
Model No. WJ-FS309
WJ-FS316
WJ-FS409
WJ-FS416
Video Multiplexer
Operating Instructions
ENGLISH
FRANÇAIS
2
The serial number of this product may be found on the bottom of the unit.
You should note the serial number of this unit in the space
provided and retain this book as a permanent record of your
purchase to aid identification in the event of theft.
Model No.
Serial No.
WARNING:
To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
The lightning flash with arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of uninsulated "dangerous voltage"
within the product's enclosure that may
be of sufficient magnitude to constitute a
risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating
and maintenance (servicing) instructions
in the literature accompanying the appliance.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
SA 1965
SA 1966
NOTE: This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications.
Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be
required to correct the interference at his own expense.
FCC Caution: To assure continued compliance, (example use only shielded interface cables when connecting to computer or peripheral devices). Any changes or modifications
not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
For U.S.A
Caution:
Before attempting to connect or operate this product,
please read the label on the bottom.
3
CONTENTS
PREFACE .................................................................................................................................................................................... 4
FEATURES .................................................................................................................................................................................. 4
PRECAUTIONS ........................................................................................................................................................................... 5
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS ..................................................................................................... 6
■ Front View ............................................................................................................................................................................. 6
■ Rear View ............................................................................................................................................................................. 8
SETUP MENU .............................................................................................................................................................................. 9
■ Setup Menu ........................................................................................................................................................................ 10
■ Alarm Setup Menu .............................................................................................................................................................. 11
■ Monitor Output Setup Menu ............................................................................................................................................... 13
■ Record Output Setup Menu ............................................................................................................................................... 14
■ Sequence Setup Menu ....................................................................................................................................................... 15
■ System Setup Menu ........................................................................................................................................................... 17
INSTALLATIONS ......................................................................................................................................................................... 22
■ Mounting in the Rack .......................................................................................................................................................... 22
SYSTEM CONNECTIONS ............................................................................................................................................................ 23
■ Basic System Connection .................................................................................................................................................. 23
■ Connection with the Time Lapse VCR ................................................................................................................................ 24
■ Connection of the Digital Disk Recorder (Example: WJ-HD100) to a Video Multiplexer .................................................... 25
■ Connection with the Monitors ............................................................................................................................................. 26
■ Connection with the WV-CU360 System Controller ............................................................................................................ 26
■ ALARM/REMOTE Connector .............................................................................................................................................. 27
■ Connection with the Alarm Sensors ................................................................................................................................... 28
■ Connection with the Alarm Output ..................................................................................................................................... 28
■ Connection with the Remote (External) Switches ............................................................................................................... 29
OPERATING PROCEDURES ....................................................................................................................................................... 30
■ Monitoring the Camera Picture ........................................................................................................................................... 30
■ Recording on the Time Lapse VCR .................................................................................................................................... 34
■ Monitoring the Playback Picture ......................................................................................................................................... 34
ALARM CONTROL FUNCTION ................................................................................................................................................... 37
■ Alarm Input ......................................................................................................................................................................... 37
■ Alarm Operation ................................................................................................................................................................. 37
■ Alarm Reset ........................................................................................................................................................................ 38
OTHER FUNCTIONS ................................................................................................................................................................... 39
■ Camera Switching Pulse Loss Display ............................................................................................................................... 39
ALL RESET .................................................................................................................................................................................. 39
OPERATING CONTROL OF SYSTEM UNITS (Supplementary) .................................................................................................. 39
■ Channel Loss Alarm ........................................................................................................................................................... 39
APPENDIX ................................................................................................................................................................................... 40
SPECIFICATIONS ........................................................................................................................................................................ 42
STANDARD ACCESSORIES ....................................................................................................................................................... 42
ENGLISH
4
PREF ACE
FEATURES
The WJ-FS309 and WJ-FS316 are Black and White Video
Multiplexers, and the WJ-FS409 and WJ-FS416 are Color
Video Multiplexers designed for use in surveillance security
systems combined with cameras, alarm sensors, a Time
Lapse VCR, two video monitors and a PC. Spot pictures
and image sequences of multiple cameras can be monitored simultaneously on two video monitors. Multiscreen
pictures and the Multiscreen sequence pictures can be displayed on Multiscreen monitors.
Camera and playback pictures can be displayed as
zoomed and stilled Spot pictures and Still Multiscreen pictures.
Setup menus for Alarm, Monitoring, Recording and Playback are available to match system preferences to your
requirements.
The WJ-FS309/FS316/FS406/FS416 and other devices compatible with Panasonic Security Data mode the bear logo
.
• The WJ-FS309 (/FS316/FS409/FS416) can be controlled
from a PC or the System Control Unit (example: WVCU360) via an RS-485 interface.
• The pictures of any connected camera can be displayed as a Spot picture on a full screen or Sequential
screen, or as shown below on a 4-, 9- or 16-segment
Multiscreen. Still and zoom modes (full screen only) are
available both for live pictures and for video playback.
(The 16-segment multiscreen is available with WJFS316 or FS416.)
• High picture quality of 720 x 480 pixels
• Multiplexed video signals with camera IDs are supplied
to the Recording Output
• Versatile recording mode initiated by alarm trigger
• Playback image is displayed automatically without need
to operate VCR/CAM button
• The full screen image can be zoomed in 2 times.
• Preset sequence of up to 16 (9) steps with dwell times
• Video loss detector
• On screen setup menu
• Secret view
• Versatile alarm capability
16-SEGMENT SCREEN
9-SEGMENT SCREEN
4-SEGMENT SCREEN
5
• Refer all work related to the installation of this
product to qualified service personnel or system
installers.
• Do not block the ventilation opening or slots on the
cover.
To prevent the appliance temperature from rising, place
the appliance at least 5 cm (2 inches) away from the
wall.
• Do not drop metallic parts through slots.
This could permanently damage the appliance. Turn
the power off immediately and refer servicing to
qualified service personnel.
• Do not attempt to disassemble the appliance.
To prevent electric shock, do not remove screws or
covers.
There are no user-serviceable parts inside. Refer maintenance to qualified service personnel.
• Handle the appliance with care.
Do not strike or shake, as this may damage the appliance.
• Do not expose the appliance to water or moisture,
nor try to operate it in wet areas.
Do take immediate action if the appliance becomes
wet. Turn the power off and refer servicing to qualified
service personnel. Moisture can damage the appliance
and also cause electric shock.
• Do not use strong or abrasive detergents when
cleaning the appliance body.
Use a dry cloth to clean the appliance when it is dirty.
When the dirt is hard to remove, use a mild detergent
and wipe gently. Afterwards, wipe off the remained part
of the detergent in it with a dry cloth.
• Do not operate the appliance beyond its specified
temperature, humidity or power source ratings.
Do not use the appliance in an extreme environment
where high temperature or high humidity exists.
Use the appliance at temperatures within –10°C +50°C (14°F - 122°F) and a humidity below 90 %.
The input power source for this appliance is 120 V AC
60 Hz.
PRECAUTIONS
6
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS
■ Front View
<WJ-FS309/FS409>
q Power Switch (POWER ON/OFF)
This switch turns the power of the video multiplexer on
or off. The LED lights up when the power is turned on.
Note: To prevent that the power of the video multiplexer
is turned off accidentally, install the supplied switch
protector as shown below.
w Alarm Reset Button (ALARM RESET)
This button resets the active Alarm mode. Pressing this
button turns off the Alarm indicator and replaces the
“Alarm” indication on the monitor screen with the camera title.
<WJ-FS316/FS416>
e Alarm Indicator (ALARM)
This indicator blinks when an alarm is activated. It
changes to steady light when the auto-reset time has
elapsed or the alarm recovery signal is received from
the VCR. To turn the indicator off, press the ALARM
RESET button.
r Multiscreen Selection Button (MULTISCREEN
SELECT)
This button selects the multiscreen pattern for the monitor. Multiscreen is available only MULTI OUTPUT mode.
Pressing this button repeatedly switches patterns as follows:
Multiscreen Picture:
4→9→4 screen segments (WJ-FS309/FS409)
4→9→16→4 screen segments (WJ-FS316/FS416)
Note: When ON is selected for QUAD SHIFT on the
MONITOR OUTPUT SETUP menu, the screen
changes by pressing this button as follows:
4A→4B→9 screen segments (WJ-FS309/FS409)
4A→4B→4C→4D→9→16 screen segments
(WJ-FS316/FS416)
t
POWER
ON
OFF
SWITCH
PROTECTER
ALARM
ALARM
RESET
MULTI SCREEN
SELECT
SPOT
MULTISCREEN
SEQ
1
2 3 4 5 6 7 8 9
t
MULTI SCREEN
SELECT
SPOT
MULTISCREEN
1
SEQ
2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
POWER
ON
OFF
SWITCH
PROTECTER
ALARM
ALARM
RESET
SWITCH
PROTECTOR
CAMERA SELECT
CAMERA SELECT
STILL
EL-ZOOM
VCR
MENU
CAM
SET
SET
ESC
STILL
MENU
ESC
EL-ZOOM
VCR
CAM
Video Multiplexer WJ-FS
Video Multiplexer WJ-FS
FS
309
FS
316
9
7
!2 Electric Zoom Button (EL-ZOOM)
This button specifies the zooming area in the multiscreen output picture. Pressing this button displays the
“+” sign representing the center of the area to be
enlarged. While the “+” sign is displayed for 5 seconds,
move the “+” sign with the cursor buttons to the desired
position and press the Increment (+) button. The designated area is enlarged.
To return to the normal picture press the Decrement (–)
or the EL-ZOOM button.
!3 MENU/ESC Button (MENU/ESC)
Pressing this button for 2 seconds or more opens the
Setup Menu of the Video Multiplexer. If pressed for less
than 1 second, it functions as the Escape button and
returns you to the previous menu.
To close the Setup menu when the setup is completed,
press the button for 2 seconds.
Notes:
• Make sure to distinguish between 1-second and 2second operation of this button.
• Opening the Setup menu does not affect the
recording signal (REC OUT) output from the rear
panel.
!4 VCR/Camera Selection Button (VCR/CAM)
This button selects either VCR playback or the camera
picture for display on the monitor. At the same time, it
disables or enables recording on the VCR, since the
connected VCR performs only playback or recording at
a time. The playback picture is displayed on the monitor if you start playing back the VCR while the LED
(Green) is on. The camera picture is displayed on the
monitor while the LED is off. The camera picture is
recorded on the tape if you start the VCR recording.
Notes:
• If PLAYBACK AUTO is set to ON in the setup,
pressing this button is ignored, instead this button
follows the VCR status automatically. VCR is selected while playing back, and CAMERA is selected
during non-playback mode of the VCR.
• There may be a delay of a few seconds after
switching this button between VCR and CAMERA
when PLAYBACK AUTO is ON.
* The picture may be disturbed for a moment after
switch between VCR and camera.
• Blinking of the LED is a warning that the ID code is
missing in the playback signal. This may happen
when using certain VCR types. In this case, the
playback picture goes straight to the monitor
instead of through the Video Multiplexer. As a
result, the playback picture will not be recognizable
unless only a single channel is recorded throughout
the tape.
The 4A screen is a compressed picture of channels
1 through 4, the 4B of channels 5 through 8, the 4C
of channels 9 through 12, and the 4D of channels
13 through 16. The 9-segment screen shows the
pictures of channels 1 through 9 in a 3x3 pattern.
t Spot/Multiscreen Selection Button
(SPOT/MULTISCREEN)
This button is used to select either the Spot output or
Multiscreen output.
y Sequence Button (SEQ)
This button activates the sequence mode. In this mode,
a series of camera pictures is displayed in succession
on the monitor screen for the specified duration.
u Camera Selection Buttons (CAMERA SELECT)
These buttons select the camera for live picture or picture recorded on the tape. When the VCR is in playback
mode and the LED on the VCR/CAM button is on, these
buttons select the specified camera picture from the
tape for display on the monitor. When the LED is off, the
buttons select the live picture of the specified camera.
i Cursor Buttons (C, D, A, B)
These buttons move the cursor in the SETUP MENU of
the Video Multiplexer, or select an area for Electronic
Zooming.
C: Downward
D: Upward
A: Left
B: Right
o Increment/Decrement Buttons (–, +)
Electronic Zooming is operated with these buttons,
Zoom In with the + button and Zoom Out with the – button. During the setup, these buttons are used to select
parameters.
!0 Set Button (SET)
This button executes the selected parameter in the
setup menu, and opens a submenu for more detailed
settings. Menu items having a submenu are identified
by a return symbol at the end of the line.
!1 Still Button (STILL)
This button selects either still or moving mode for display on the multiscreen output monitor. Pressing a
CAMERA SELECT button will display the corresponding picture either in still or moving mode. When a still
picture is displayed, the LED lights. Pressing the button
again restores the moving picture and turns off the LED.
Note: Please note that the tape continues running while
the picture is stilled. You may sometimes have to
rewind the tape to the desired position.
Note: Do not press more than two buttons on the front
panel simultaneously. This may cause malfunction.
8
SIGNAL
GND
ALARM/REMOTE
OUT
IN
VIDEO
16 15 14 13 12 11 10 9 8
16 15 14 13 12 11 10 9 8
7654 21
76543321
PLAY IN
REC OUT
SPOT OUT
DATA
CAMERA
SW IN
MULTI
SCREEN OUT
io
u!1
!0
q Video Input Connectors (VIDEO IN)
These connectors accept a composite video signal
from a camera.
Note: If the input signals have a high jitter content, as in
the case of a VCR playback picture, it may not be
possible to synchronize this unit.
w Video Output Connectors (VIDEO OUT)
The video signals connected to the Video Input
Connectors (VIDEO IN) are looped through to these
connectors with an automatic 75 Ω termination.
e Alarm/Remote Control Connector (ALARM/
REMOTE)
This connector accepts the alarm signals from the
associated alarm sensor units and the control signals
from the external system.
r Playback Input Connector (PLAY IN)
The playback signal from the time lapse VCR is supplied to this connector.
t Record Output Connector (REC OUT)
The recording signal for the time lapse VCR is provided
via this connector.
y Multiscreen Output Connector (MULTISCREEN OUT)
The video output signal for the multiscreen monitor is
provided via this connector.
u Spot Output Connector (SPOT OUT)
Provides the video output signal for the spot monitor.
i Data Port (DATA)
For exchange control data with the WV-CU360 System
Control Unit or a PC within a system.
o Camera Switching Input Connector
(CAMERA SW IN)
The camera switching pulse from the time lapse VCR is
supplied to this connector.
The camera switching interval (Sequential Dwell Time)
can be synchronized with the time lapse mode set in
the associated time lapse VCR.
!0 Signal Ground Terminal (SIGNAL GND)
!1 Power Cord
■ Rear View
<WJ-FS309/FS409>
<WJ-FS316/FS416>
987 6543 21
IN
OUT
987 6543 21
VIDEO
PLAY IN
ALARM/REMOTE
REC OUT
MULTI
SCREEN OUT
i
DATA
SPOT OUT
u!1
o!0
CAMERA
SW IN
SIGNAL
GND
9
SETUP MENU
In the SETUP MENU you can set preferences for ALARM,
MONITOR, REC OUT, SEQUENCE and SYSTEM to meet
your requirements.
● Displaying the SETUP MENU
1. Confirm that the camera and peripherals are connected
correctly and securely.
2. Turn on the power switches of all system components.
3. Press the MENU/ESC button for 2 seconds or more.
The SETUP MENU appears on the monitor as shown
below.
WJ-FS316 SETUP
ALARM SETUP
MONITOR OUTPUT SETUP
REC OUTPUT SETUP
SEQUENCE SETUP
SYSTEM SETUP
MENU
ESC
• The following buttons are used in the SETUP MENU:
C: Moves the cursor downward.
D: Moves the cursor upward.
A: Moves the cursor to the left.
B: Moves the cursor to the right.
– : Selects the mode or parameter.
+ : Selects the mode or parameter.
SET: Executes the selections and displays a submenu
for an item with the ( ) mark.
• Press the MENU/ESC button to execute the currently
highlighted setting and return to the previous menu in
the SETUP MENU.
• To finalize the setting and return to normal viewing,
press the MENU/ESC button for 2 seconds while the
SETUP MENU is displayed.
Note: If alarm is activated during the setup operation,
the SETUP MENU disappears and the display
returns to the normal picture. Any settings previously made take effect, even if the MENU/ESC button
was not pressed yet.
SET
9 10 11 12 13 14 15
The items of the WJ-FS309/FS409 SETUP MENU are the
same as in the WJ-FS316/FS416 SETUP MENU.
<WJ-FS316/FS416>
1
SET
2 3 4 5 6 7
<WJ-FS309/FS409>
10
SETUP MENU
ALARM SETUP
(Alarm Setup)
Page 11
MULTI OUTPUT
TITLE DISP (Camera Title Display)
STILL DISP (Still Display)
BORDER (Border Display)
QUAD SHIFT (Quad Shift)
SECRET VIEW
BAUD RATE
DATA BIT
TITLE DISP
TITLE DISPLAY (Record Title Display)
REC MODE (Recording Mode)
SPOT OUTPUT
TITLE SETUP (Camera Title Setup)
TITLE POSI (Camera Title Display Position)
CAM SW LOSS (Camera Switching Pulse Loss Alarm)
PLAYBACK AUTO (Automatic VCR Mode)
PASSWORD (Password)
PWR ON MULTI (Startup Multiscreen)
PWR ON SPOT (Startup Spot Screen)
COM. SETUP (Communication Setup)
UNIT ADDRESS
CAM NUMBER (Camera Number)
WAIT TIME
ALARM DATA
PARITY CHECK
STOP BIT
SW INTERVAL (Field Timing)
NO. OF CAMS (Camera Channel)
ENCODE
MONITOR OUTPUT SETUP
(Monitor Output Setup)
REC OUTPUT SETUP
(Record Output Setup)
SEQUENCE SETUP
(Sequence Setup)
SYSTEM SETUP
(System Setup)
Page 13
Page 17
MULTI OUTPUT
AUTO SKIP (Automatic Skip)
SEQ MODE
AUTO SKIP (Automatic Skip)
SPOT OUTPUT
MLT/SPT SEQ SETUP
Page 15
DYNAMIC REC
(Dynamic Recording)
ALM REC MODE (Alarm Recording Mode)
AUTO RESET (Automatic Reset)
ALM DISPLAY (Alarm Display)
ALM OUTPUT (Alarm Output Duration)
ALM BUZZER (Alarm Buzzer Duration)
ALM INPUT (Alarm Input)
VIDEO LOSS (Video Input Signal Loss Alarm)
MLT OUT MODE (Alarm Channel Multiscreen Output Mode)
SPT OUT MODE (Alarm Channel Spot Output Mode)
Page 14
■ Setup Menu
As shown below, the SETUP MENU has five main submenus: Alarm Setup, Monitor Output Setup, Record Output Setup,
Sequence Setup and System Setup.
All of these submenus are further divided into additional submenus.
11
1. Move the cursor on GROUP in the DYNAMIC REC
line and press the SET button to open the GROUP
SETUP menu shown above.
2. Move the cursor to the desired position by pressing
the C, D, A, B buttons.
Note: To turn over the page for WJ-FS316/FS416,
keep the cursor moving up or down.
3. Select the camera number by pressing the
Increment (+) or Decrement (–) button.
4. Repeat steps 2 and 3 until all groupings are
entered.
Note: Assigning one camera channel to plural
alarm inputs is acceptable.
2. ALM REC MODE
This item lets you select the time interval (field rate) for
switching the camera channel for the REC OUT signal. This
setting takes effect only when an alarm is activated.
1. Move the cursor to the ALM REC MODE parameter.
2. Select a field rate or EXT by pressing the + or – button.
The initial factory setting is 004.
004 - 128: REC OUT signal is switched from one cam-
era channel to another at the field rate specified
here. The appropriate field rate may vary depending on the VCR model. Consult the VCR specifications on the field rate.
EXT: Switching of the REC OUT signal is controlled by
the camera switching signal supplied by the connected VCR.
1. DYNAMIC REC
This item lets you select the camera channel(s) whose picture is to be recorded on the VCR when an alarm signal is
received. There are priority options for recording of channel(s) ranging from equal priority of all channels to exclusive recording of a specified channel.
1. Move the cursor to the DYNAMIC REC parameter.
2. Select OFF, ALM - PRI, ALM-ONLY or GROUP by
pressing the + or – button.
The initial factory setting is OFF.
OFF: The video signals are recorded from channels
number 1 to 9 (WJ-FS309/FS409) or 1 to 16 (WJ-FS
316/FS416) regardless of any channels receiving
the alarm signal.
ALM - PRI: The video signal of the channel that
received the alarm signal is recorded with more
fields than normal.
ALM-ONLY: The recording output is monopolized by
the picture of the channel that received the alarm,
while the pictures on other channels are omitted.
Note: ALM-ONLY is not applicable, when a WJ-DR200
AV Disc Recorder is connected to the unit.
GROUP: Up to 4 channels are merged into a group.
When an alarm is received, the video signals of this
channel group are recorded with more fields than
normal.
If the DYNAMIC REC parameter is on GROUP, proceed
as follows:
■ Alarm Setup Menu
Move the cursor to ALARM SETUP on the SETUP menu,
then press the SET button. The ALARM SETUP menu
appears on the monitor screen as shown below.
WJ-FS316 SETUP
ALARM SETUP
MONITOR OUTPUT SETUP
REC OUTPUT SETUP
SEQUENCE SETUP
SYSTEM SETUP
ALARM SETUP
DYNAMIC REC OFF
ALM REC MODE 004
AUTO RESET OFF
ALM DISPLAY ON
ALM OUTPUT 2S
ALM BUZZER 2S
ALM INPUT N.O.
VIDEO LOSS ON
MLT OUT MODE SPOT
SPT OUT MODE SPOT
2/2
GROUP SETUP 1/2
CH CH CH CH
ALM 1 → 1 -- -- - ALM 2 → 2 -- -- - ALM 3 → 3 -- -- - ALM 4 → 4 -- -- - ALM 5 → 5 -- -- - ALM 6 → 6 -- -- - ALM 7 → 7 -- -- - ALM 8 → 8 -- -- --
GROUP SETUP
CH CH CH CH
ALM 1 → 1 -- -- - ALM 2 → 2 -- -- - ALM 3 → 3 -- -- - ALM 4 → 4 -- -- - ALM 5 → 5 -- -- - ALM 6 → 6 -- -- - ALM 7 → 7 -- -- - ALM 8 → 8 -- -- - ALM 9 → 9 -- -- --
<WJ-FS316/FS416>
<WJ-FS309/FS409>
12
Notes:
• If set to EXT, make sure that the CAMERA SW IN
terminal on the rear panel is connected to the Time
Lapse VCR.
• Depending on the mutual timing between the alarm
trigger and the field rate, the initial picture recorded
after an alarm is activated may not be related to the
alarm.
3. AUTO RESET
This item lets you set the time the Video Multiplexer retains
the alarm mode before automatic resetting to non-alarm
mode. When alarm is activated the display of the camera
title on the monitor alternates with “ALARM”. After the time
you set, the previous, non-alarm mode is restored.
1. Move the cursor to the AUTO RESET parameter.
2. Select the desired duration by pressing the + or – button.
The initial factory setting is OFF.
OFF: Disables auto reset.
1-30S, 40S, 50S, 1-5M: Selects an alarm duration from
1-30, 40, 50 seconds or 1-5 minutes.
4. ALM DISPLAY
This item lets you enable or disable the “Alarm” display
overlaid on the camera picture while the alarm is activated.
1. Move the cursor to the ALM DISPLAY parameter.
2. Select ON or OFF by pressing the + or – button.
The initial factory setting is ON.
ON: Enables alarm display on the monitor.
OFF: Disables alarm display on the monitor.
5. ALM OUTPUT
This item lets you select the duration of the Alarm Output
signal. When the alarm signal comes in, the Alarm Output
signal is supplied to the external device connected. Consult
the specifications of the external device on the duration.
1. Move the cursor to the ALM OUTPUT parameter.
2. Select the parameter by pressing the + or – button.
The initial factory setting is 2S.
OFF: No Alarm Output signal is supplied, regardless of
an incoming alarm.
1S–30S, 40S, 50S, 1M–5M: The connected external
device is driven for the duration set here. S and M
stand for seconds and minutes.
EXT: The Alarm Output signal continues until the
ALARM RESET button is pressed or an alarm
recovery signal is supplied from the VCR.
6. ALM BUZZER
This item lets you select the ringing duration of the built-in
alarm buzzer when alarm is activated.
1. Move the cursor to the ALM BUZZER parameter.
2. Select the duration by pressing the + or – button.
The initial factory setting is 2S.
OFF: Disables the alarm buzzer output.
1-30S, 40S, 50S, 1-5M: Selects an alarm duration from
1-30, 40, 50 seconds or 1-5 minutes.
EXT: The alarm buzzer continues to beep until the
ALARM RESET button is pressed or an external
alarm recover signal is received.
7. ALM INPUT
This item lets you select the input form of the alarm signal.
Consult the specifications of the sensor device.
1. Move the cursor to the ALM INPUT parameter.
2. Select the parameter by pressing the + or – button.
The initial factory setting is N.O.
N.O.: Stands for Normally Open type contact. When
active the contact closes.
N.C.: Stands for Normally Closed type contact. When
active the contact opens.
8. VIDEO LOSS
This item lets you enable or disable the channel loss display on the monitor screen if the video signal is interrupted
due to, for example, a cable disconnection.
1. Move the cursor to the VIDEO LOSS parameter.
2. Select ON or OFF by pressing the + or – button.
The initial factory setting is ON.
ON: Enables the channel loss display (CHXX LOSS) on
the monitor screen.
Note: XX indicates the channel number.
OFF: Disables the channel loss display on the monitor
screen.
Note: If the video signal is interrupted and the message
“CHXX LOSS” is displayed, check that the connections are correct and firm, then input the video signal again or press the ALARM RESET button. This
resets the channel loss display.
13
9. MLT OUT MODE
This item lets you select whether to switch the multiscreen
output monitor screen automatically to the camera picture
of the channel whose alarm is activated.
1. Move the cursor to the MLT OUT MODE parameter.
2. Select OFF or SPOT by pressing the + or – button.
The initial factory setting is SPOT.
OFF: Ignores alarm activation and continues to display
the pictures in the mode selected previously. All
buttons except alarm reset button do not valid on
condition that alarm reset does not complete.
SPOT: The camera picture whose alarm is activated is
displayed and retained until the alarm is reset.
10. SPT OUT MODE
This item lets you select whether to switch the spot output
monitor screen automatically to the camera picture of the
channel whose alarm is activated.
1. Move the cursor to the SPT OUT MODE parameter.
2. Select OFF or SPOT by pressing the + or – button.
The initial factory setting is SPOT.
OFF: Ignores alarm activation after and continues to
display the pictures in the mode selected previously. All buttons except alarm reset button do not valid
on condition that alarm reset does not complete.
SPOT: The camera picture whose alarm is activated is
displayed and retained until the alarm is reset.
■ Monitor Output Setup Menu
1. MULTI OUTPUT
Move the cursor to MONITOR OUTPUT SETUP on the
SETUP menu, then press the SET button. The MONITOR OUTPUT SETUP menu appears on the monitor
screen as shown below.
WJ-FS316 SETUP
ALARM SETUP
MONITOR OUTPUT SETUP
REC OUTPUT SETUP
SEQUENCE SETUP
SYSTEM SETUP
MONITOR OUTPUT SETUP
MULTI OUTPUT
TITLE DISP ON
STILL DISP ON
BORDER WHITE
QUAD SHIFT OFF
SECRET VIEW OFF
SPOT OUTPUT
TITLE DISP ON
1-1. TITLE DISP
This item lets you enable or disable the camera title display
overlaid on the multiscreen picture.
1. Move the cursor to the TITLE DISP parameter.
2. Select ON or OFF by pressing the + or – button.
The initial factory setting is ON.
ON: Enables display of the camera title.
OFF: Disables display of the camera title.
1-2. STILL DISP
This item lets you enable or disable the subtitle “STILL”
overlaid on the multiscreen output picture.
1. Move the cursor to the STILL DISP parameter.
2. Select ON or OFF by pressing the + or – button.
The initial factory setting is ON.
ON: Enables display of the subtitle “STILL”.
OFF: Disables display of the subtitle “STILL”.
Loading...